Optimum Redesign of Axial Fan Blade Attachment
Optimum Redesign of Axial Fan Blade Attachment
Optimum Redesign of Axial Fan Blade Attachment
ABSTRACT
Finite element analysis (FEA) is a computerized method for predicting how a product reacts to real-world
forces, vibration, heat, fluid flow, and other physical effects. Finite element analysis shows whether a product will
break, wear out, or work the way it was designed. This project work was based on the analysis of axial fan blade
attachment where by a complete 3D model was built for performing FEA. The acceptability of a new design
regarding to the mechanical loads and consisting of dividing the hub into two parts instead of using a solid hub is
studied. From the model some critical parameters for the attachment of the blade with respect to the stresses were
chosen such as the rotational speed, fillet of the blade and the neck of the blade. Parametric studies of these
parameters were carried out in order to suggest the new design. Bearing in mind that a safety factor of 2 was the
prerequisite, based on the analysis performed on ANSYS Workbench, it was suggested from the preliminary
design that the axial fan can operate in two specific scenarios consisting of a rotational speed of 1771 rpm and a
rotational speed of 1594 rpm. Using this set of parameters, a suggestion was drawn up on the blade fillet which
will give the lower stress. For manufacturing feasibility blade fillet size of 30 to 35mm was recommended while a
size of 45mm was recommended on the neck of the blade. A modal analysis was performed in order to find at what
frequency will the model be vibrating and a lowest and critical frequency of 16.8 Hz was obtained. Finally, a
fatigue analysis of some interesting areas was performed in order to determine the numbers of cycles before
fatigue failure occur. It was recommended to use the rotational speed mention previously since these speeds have
offered a High Cycle Fatigue results.
1. Introduction
This report covers the analysis of a fan blade attachment. The purpose of changing the design is to reduce the cost
and the effort in fabrication of a component called the axial fan hub.
2.
An axial fan is a type of compressor which moves air or gas parallel to the axis of rotation unlike the centrifugal or
radial flow fans which moves air or gas perpendicular to the axis of rotation (Anon, 2002).
3.
This report focuses on analyzing the attachment of the fan blade, according to mechanical loads. The stresses
acting on both the blades and the hub are analyzed, a modal analysis is performed and finally, a fatigue analysis is
carried out using the stress life approach.
Throughout history, the use of fans and ventilation systems has been increasing parallel to the industrial
developments as well as the requirements of the situations. Although Leonardo da Vinci in the end of the 15th
century described fans in his designs, the spreading of them became more important with the appearance and
exploitation of the mining industry. Thus, along the 16th century, due to the extraction of coal, metal ores and
other substances the ventilation became basic in order to avoid flow gas which might either asphyxiate the miners
or explode with disastrous results. Indeed, the first mine ventilation system was published by Georgious Agricola
(1912). Many of the sophisticated airflow systems used nowadays were embodied in his book. However, due to
the lack of knowledge of the air properties, safety and health measures, non-important advances appeared until the
end of 17th century thanks to the investigation of some important scientists like Galileo, Torricelli, Pascal, Boyle
and Newton. Along the 18th and the beginning of the 19th century, until the First World War, the main researches
were developed in United Kingdom, both in the seat of the British Government
and the mine industry. The present day applications of fans are far too numerous to list owe to the improvement
achieved, high lighting the aviation industry (Cory, 2005).
An axial flow fan is a machine which creates flow within a fluid (gas) in such a way that air flows linearly along
the axis of it. It is composed of blades that force air to move parallel to the shaft about the axis at which the blades
rotate, which are rigidly secured. Industrial axial are used in extremely conditions such as high temperature, large
vibrations amplitudes or high corrosion, which cause large strains. Due to this, both the hub and the fan blades are
made out of casting aluminum, which is capable to resist aggressive environments, have light weight and be easily
malleable to the conditions required. However, now days, aviation industries are using a solid model, which means
a n increase of the material used and consequently, the cost of production is higher. Photographs of existing & new
design of an impeller fan blade are shown in Figure 1 and Figure 2.
Figure 3: Detail of the fillet on the blade in the initial design (mm)
Neck of the blade is a crucial part due to the geometry, since the neck of the blade is the support of the blade &
that is, the base of the blade. Then, it is expected to give high stress concentration. Crack would start propagating
either from the top of the neck of the blade or from the bottom. For this reason, a parametric study was required in
order to examine what will be the outcome if the neck of the blade had increased while rotating at the maximum
speed. Therefore, three parameters were chosen and analyzed at different rotational speed. A neck diameter of 45
mm (Figure 4) had been used on the preliminary design but this value was increased in such a way that the stress
around the blade would decrease or increase when it would be subjected to certain rotational speed parameters.
The values chosen were 47, 49 and 51 mm.
2.1.1.1
Material Properties
It is necessary in order to perform the analysis in Finite Element Software to specify the material
properties of the model. The whole axial fan was modeled using Aluminum Alloy except for the fasteners
(screw and washers), which were modeled using Structural Steel. A linearly elastic material model was
used to perform the analysis. In Table 1, the main material properties of both elements are shown
ALUMINUM ALLOY
STRUCTURAL STEEL
Density (xyz{)
2770
7780
7 106
2.06 1066
Poissons Ratio
0.3
0.3
2.7 106
7.7 106
2.8 10
2.5 10
3.1 10
4.6 10
Mesh
An important aspect when performing an FE analysis is to carry out the mesh. The axial fan was FE modeled
using a 10 node tetrahedral element. This element was part of the software package used and the software uses
the automatic meshing in order to create the mesh. The element is known in performing better when it comes to
stress analysis in structures and solid mechanics (ANSYS, 2004). The element is also known for having four
corner nodes, three degrees of freedom at each node (ANSYS, 2004). Figure 3 shows a typical 10 Node element.
Another concept pops up when performing the mesh is the difference between coarse and fine mesh. The
literature shows that the coarse mesh cannot be trusted. In order to get accurate results, the mesh has to be finer
when certain geometry changes such as fillets, holes, notches and sharp edges appear (Figure 4)(Cook et al,
2002). According to the analysis requirement coarse mesh on blades in assembly (Figure 6) & finer mesh on
blade (Figure 7) for fillet study were meshed.
Figure 5: Quadratic (10 node) tetrahedron element with planar faces and side midpoints
In order to perform the analysis, all loads, boundary conditions, mesh and contact relations have to be defined in
ANSYS workbench.
Two types of load were considered when performing the analysis. The first load was the centrifugal force. The
centrifugal force is applied as a fictive force in order to achieve the equilibrium. Although it is a virtual force, it
is defined like a volume; otherwise the results could not be trusted since the model would be rotating (Figure 8)
CONDITION
DisplacementX
Fixed
DisplacementY
Fixed
DisplacementZ
Fixed
Rotational
speed
(rpm)
Max.Stress
(MPa)
(Insidethe
boss)
BladeFillet
Stress
(MPa)
Neckofthe
Blade
Stress
(MPa)
3000
367
25.7
26.5
26.5mm
BladeFilletSize
2700
308
28.5
23.3
2430
241
24.7
17.4
2187
201
17.2
13.5
1968
158
12.9
11.8
1771
121
8.4
9.5
1594
104
7.2
7.5
After these results, in order to have both a better understanding and easier way to compare the results, from
Figure 13 graph comparing the four parameters against the blade fillet size and each rotational speed (horizontal
axis) are plotted. It is important to notice that, from the results obtained in the analysis, the maximum stress
occurred at the same point (the boss) while using different blade fillet size. Moreover, all the values are
converged.
Figure 13: Maximum stress against blade fillet size for each rotational speed
3.2 MODAL ANALYSIS RESULTS
The results of the natural frequencies obtained through the modal analysis are shown in Table 3. Furthermore, in
Figure 14 is represented a graph plotting the mode numbers against the Eigen frequencies. Also, it is compared
the coarse mesh against the fine mesh (Figure 7).
MODE
FREQUENCY(Hz)
FREQUENCY(Hz)
(Finemesh)
10
(Coarsemesh)
16.8
17
63.2
64.9
63.3
65
67.3
68.8
67.5
69.6
67.9
69.6
Figure 14: Mode number against natural frequencies and coarse mesh against fine mesh
3.3 FATIGUE ANALYSIS
In a similar way than in previous analyses, the constant amplitude load is represented in Figure 15. The fatigue
loading cycle is caused by the variable stress at a point with respect to the time. The stress at a point is varied due
to the rotation of the fan blades. The origin of the fatigue can be due to the geometry change where stress
concentration may occur. This will result in a fatigue crack which will occur at the discontinuities in the material.
The other origin of fatigue may also be in the microstructure of the material which may contain voids.
Furthermore, the relation between the rotational speeds against the number of cycles is represented in Figure 16
and finally pictures of the fillet of the blade and the neck of the blade are represented in Figure 17 and Figure 18
where it is shown the remaining cycle before the part fails due to fatigue. Table 4 shows the results of the fatigue
analysis where N represents the number of cycles where cycle represents one complete turn of the axial fan.
11
Figure 15: Constant amplitude load obtained from ANSYS Workbench analyses
Figure 16: Rotational speed against Number of cycles, where N stands for the number of cycle
12
Figure 17: Fatigue Analysis on the neck of the blade at 1594 rpm
4.0 Conclusion
As a general conclusion, from the above results, it could be noticed from the preliminary design that an increase
in the rotational speed together with the pressure load will cause an increase in the maximum stress, stress in the
blade fillet and stress in the neck of the blade. Bearing in mind that a safety factor of 2 was the pre-requisite, and
taking into account that the safety factor is given as the ratio between the ultimate tensile strength over the design
load or the maximum stress, the following conclusions can be stated:
With respect to the parametric study, it can be suggested that the required operating speed should be between
1500 rpm to 2000 rpm. The size of the diameter of the neck of the blade should be 45 mm, while the size of the
fillet of the blade should be between 30 mm and 35 mm. Also, according to the parametric study, including the
reduction of the material with respect to the old design, the new design is acceptable according to the mechanical
requirements explained along this dissertation.
All these results can be trusted according to the values obtained throughout the convergence analysis, where the
prerequisite of percentage of change less than 2% was fulfilled.
13
Regarding to the modal analysis, as mention in section 3.2, all the natural frequency maybe of interested.
However when taking into account the suggested rotational speeds, it could be said that the first two natural
frequency might be of interested and there may be problem at start up since the recommended rotational speeds
are between the first and second natural frequencies.
With respect to the fatigue analysis, evaluating the results obtained in the interested area, it can be suggested that
the design meets the requirements of use if it operates at 1771 and 1594 rpm since the number of cycle falls
under the High Cycle Fatigue and both rotational speed fulfilled the requirement of the Safety Factor. It can be
also stated that the constant amplitude graph obtained during the analysis implies full reverse condition, that is,
R=-1.
14
5.0 References:
Chambon,L.,2001. Aunifiedfracturemechanicsapproachtofrettingfatiguecrack
growth.,Massachusetts:MassachusettsInstituteofTechnology.
Chattopdhyay,S.,2008.Designfatiguecurvesbasedonsmallcrackgrowthandcrack
closure.Journalofappliedscienceandengineeringtechnology.
Ciavarella,M.&Demelio,G.,2001.Areviewofanalyticalaspectsoffrettingfatigue,
withextensiontodamageparameters,andapplicationtodovetailjoints.International
Journalof,Volumen38,pp.17911811.
Cook,R.,Malkus,D.S.,Plesha,M.E.&Witt,R.J.,2002.ConceptsandApplicationsof
FiniteElementAnalysis.4ed.s.l.:Rev.ed.Wiley.
Cory,W.,2005.FansandVentilation:Apracticalguide.2ed.s.l.:Elsevier.
Dixit,U.,2009.FiniteElementMethod:Anintroduction.En:C.L.India,ed. Finite
ElementMethodsForEngineers. Guwahati:DepartmentofMechanicalEngineering,
IndianInstituteofTechnology.
Fatemi,A.,2013.FatiguetestsandStressLife(SN)approach,Toledo:Universityof
Toledo.