Scribd
Upload
130 views

Programming A Repeater Channel

This document provides instructions for programming a repeater channel with a 600kHz minus offset and 100.0Hz CTCSS tone on a UV85 radio. The steps are: 1) set the radio to VFO mode; 2) select the upper display; 3) turn off dual watch; 4) delete prior channel data; 5) set the 600kHz repeater offset; 6) set a minus transmit frequency shift; 7) set the 100.0Hz CTCSS tone; 8) enter the 146.700MHz receive frequency; 9) store the receive frequency in channel 1; and 10) store the transmit frequency in channel 1.

Uploaded by

totChing
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
130 views

Programming A Repeater Channel

This document provides instructions for programming a repeater channel with a 600kHz minus offset and 100.0Hz CTCSS tone on a UV85 radio. The steps are: 1) set the radio to VFO mode; 2) select the upper display; 3) turn off dual watch; 4) delete prior channel data; 5) set the 600kHz repeater offset; 6) set a minus transmit frequency shift; 7) set the 100.0Hz CTCSS tone; 8) enter the 146.700MHz receive frequency; 9) store the receive frequency in channel 1; and 10) store the transmit frequency in channel 1.

Uploaded by

totChing
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Programming a Repeater Channel with any offset

(Standard or Odd Split)


This example is for: 146.700 MHz
600kHz minus offset
into channel 1
CTCSS tone 100.0 (optional

1.

Set radio to VFO Mode (Frequency Mode)


a.) UV85 series - Press VFO/MR button

2.

Select Display A (this is a must)


a.) UV85- Press [A/B]
and select the Upper Display.

3.

Disable TDR (Dual Watch/Dual RX/Dual standby) which toggles between A and B.
Press [Menu] 7 [Menu]
Select OFF
Press [Menu] [Exit]

4.

Delete Prior Data from the channel to be programmed.


Press [Menu] 2 8 [Menu]
Enter 1 (Memory Channel to clear)
Press [Menu] [Exit]

5.

Enter the Repeater Offset.


Press [Menu] 2 6 [Menu]
Enter 0 0 6 0 0
Press [Menu] [Exit]

6. Enter the Transmit Frequency Shift.


Press [Menu] 2 5 [Menu]
Enter 2 for Minus shift.
Press [Menu] [Exit]
7. Set CTCSS or DCS codes for Transmit.
( example = CTCSS TX tone 123.0 Hz )
Press [Menu] 1 3 [Menu]
Enter 1 0 0. 0 [Menu] [Exit]
8. Enter the repeater output frequency, 1 4 6 . 7 0 0
9. Store RX frequency
Press [Menu] 2 7 [Menu]
Enter 1 (Memory Channel) ( 000 to 127 )
This is the channel that was cleared in step 4.
Press [Menu] [Exit]

10. Press the [ * Scan ] button.


This activates Reverse Mode and displays the TX frequency.
11. Press [Menu] 2 7 [Menu]
Enter the same Memory Channel entered above.
Press [Menu]
12. Press the [* Scan] again to exit the Reverse Mode.
13. Press [Exit]
This will now appear it in the channel list when you switch to Channel Mode. (MR)

SUMMARY of above
146.700, - .600 split/offset, 100.0 tone

1.

Set radio to VFO Mode (Frequency Mode)

2.

[EXIT A/B] must be set to Upper Display.

3.

Turn TDR OFF


[Menu] 7 [Menu] OFF [Menu] [Exit]

4.

Delete Prior Data


[Menu] 2 8 [Menu] Ch No. (1) [Menu] [Exit]

5.

Repeater Offset.
[Menu] 2 6 [Menu] 0 0 6 0 0 [Menu] [Exit]

6. Enter the TX Frequency Shift.


[Menu] 2 5 [Menu] Shift(- +) [Menu] [Exit]
7. Set TX CTCSS or DCS codes for Transmit.
[Menu] 1 3 [Menu] 1 0 0. 0 [Menu] [Exit]
9. Enter RX frequency
146.700
9. Store RX frequency
[Menu] 2 7 [Menu] Ch No. (1) [Menu] [Exit]
10.

Reverse RX TX display
[ * Scan ]

11. [Menu] 2 7 [Menu] Ch No. (1) [Menu] [* Scan] [Exit]


Switch to Channel Mode. (MR)

You might also like