Scribd
Upload
71 views

Programming A Basic Simplex Channel

This document provides instructions for programming a simplex channel of 150.995 MHz without a tone into channel 1 of a UV85 series radio. The summary is: 1. Set the radio to VFO mode and the upper display. 2. Turn off TDR mode. 3. Delete any prior data from channel 1. 4. Store the 150.995 MHz receive frequency into channel 1. 5. Store the 150.995 MHz transmit frequency into channel 1.

Uploaded by

totChing
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
71 views

Programming A Basic Simplex Channel

This document provides instructions for programming a simplex channel of 150.995 MHz without a tone into channel 1 of a UV85 series radio. The summary is: 1. Set the radio to VFO mode and the upper display. 2. Turn off TDR mode. 3. Delete any prior data from channel 1. 4. Store the 150.995 MHz receive frequency into channel 1. 5. Store the 150.995 MHz transmit frequency into channel 1.

Uploaded by

totChing
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Programming a Basic Simplex Channel (No Tone)

into channel 1
The next example shows entering TX and RX frequencies without the Shift (25) or
Offset (26) functions.
This may be more reliable, since only the "A" display works for programming memories,
thus, the radio can only remember one offset value for programming purposes.
To demonstrate, here is how you would program 150.995 simplex into memory 1.
There is no CTCSS tone in this example.
1.

Set radio to VFO Mode (Frequency Mode)


a.) UV85 series - Press VFO/MR button

2.

Select Display A (this is a must)


a.) UV85 - Press [A/B]
and select the Upper Display.

3.

Disable TDR (Dual Watch/Dual RX) which toggles between A and B.


Press [Menu] 7 [Menu]
Select OFF
Press [Menu] [Exit]

4.

Delete Prior Data from the channel to be programmed.


Press [Menu] 2 8 [Menu]
Enter 1 (Memory Channel to clear)
Press [Menu] [Exit]

5.

Store RX frequency
Enter 1 5 0.9 9 5
Press [Menu] 2 7 [Menu]
Enter 1 1 (Memory Channel)
Press [Menu] [Exit]

6.

Store TX frequency
Enter 1 5 0. 9 9 5 again
Press [Menu] 2 7 [Menu]
Enter 1 (Memory Channel)
Press [Menu] [Exit]

7.

The simplex channel is now programmed.

SUMMARY of above
RX / TX 150.995, no tone
into channel 1

1.

Set radio to VFO Mode (Frequency Mode)

2.

[EXIT A/B] must be set to Upper Display.

3.

Turn TDR OFF


[Menu] 7 [Menu] OFF [Menu] [Exit]

4.

Delete Prior Data


[Menu] 2 8 [Menu] Ch No. (1) [Menu] [Exit]

5. Store RX frequency into channel


1 5 0 . 9 9 5 [Menu] 2 7 [Menu] Ch No. (1) [Menu] [Exit]
6. Store TX frequency into channel
1 5 0 . 9 9 5 [Menu] 2 7 [Menu] Ch No. (1) [Menu] [Exit]

Switch to Channel Mode by pressing (VFO/MR)

You might also like