Scribd
Upload
90 views

3 Process Variables Part 2

The document discusses pressure measurement and concepts including absolute pressure, gauge pressure, atmospheric pressure, and the use of manometers. It provides three key points: 1) It defines absolute pressure, gauge pressure, and their relationship to atmospheric pressure. Absolute pressure is measured relative to a vacuum while gauge pressure is measured relative to atmospheric pressure. 2) It describes the use of manometers to measure pressure differences using the general manometer equation relating pressure difference to the difference in fluid levels. 3) It provides equations for calculating pressure differences for various types of manometers including open-ended, sealed-end, and differential manometers depending on whether one side is open to the atmosphere or under vacuum.

Uploaded by

Snow Drop
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
90 views

3 Process Variables Part 2

The document discusses pressure measurement and concepts including absolute pressure, gauge pressure, atmospheric pressure, and the use of manometers. It provides three key points: 1) It defines absolute pressure, gauge pressure, and their relationship to atmospheric pressure. Absolute pressure is measured relative to a vacuum while gauge pressure is measured relative to atmospheric pressure. 2) It describes the use of manometers to measure pressure differences using the general manometer equation relating pressure difference to the difference in fluid levels. 3) It provides equations for calculating pressure differences for various types of manometers including open-ended, sealed-end, and differential manometers depending on whether one side is open to the atmosphere or under vacuum.

Uploaded by

Snow Drop
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 22

ChE 31

INTRODUCTION TO
CHEMICAL ENGINEERING

2nd sem. 2013-2014


Prepared by: CGAlfafara
Edited by: JACapunitan

PROCESS VARIABLES PART 2

PRESSURE
hydrostatic pressure
absolute pressure, gauge pressure and atmospheric pressure
barometric pressure
standard atmospheric pressure
vacuum pressure
manometers

PRESSURE
* Pressure = Force/Area
SI units = N/m2 = Pascal (Pa)
Other Units: lbf/in2 (psi), dyne/cm2

Physical Interpretations of Pressure


* Fluid Pressure = F/A = minimum force exerted on a frictionless plug in the
hole to keep the fluid from emerging

PRESSURE
Hydrostatic Pressure = pressure of the fluid at the base of a column
PRESSURE ON A STATIC (non-moving) COLUMN OF FLUID OF HEIGHT, h

Pressure at the
base of a column
of liquid

pressure at
the top

hydrostatic
pressure

P P0 g h

PRESSURE
In engineering practice, pressure is sometimes expressed as the head of a particular fluid.

Head of a fluid is the height of a hypothetical column of a fluid that would exert the
given pressure at the base if the pressure at the top were zero.

P P0 g h

P 0 0

P gh
P

h head of fluid

Practice Problems

Express a pressure of 2.00 x 105 Pa in terms of


mmHg. Density of mercury is13,600 kg/m3.
What is the pressure 30.0 m below the surface
of a lake? Atmospheric pressure at the surface
of the lake is 10.4 mH2O and the density of
H2O is 1,000 kg/m3. g=9.807 m/s2; 1
atm=1.035 x 105 N/m2 = 10.33 mH2O.

ABSOLUTE & GAUGE PRESSURES


Pressure can be expressed by either absolute or relative scales.
Absolute Pressure: pressure measured relative to a fixed reference point of zero
pressure, (in a vacuum).
Gauge Pressure: pressure measured relative to the atmosphere. (usually measured by
most pressure measurement devices).
Whether relative or absolute pressure is measured in a pressure measuring device depends on
the nature of the instrument used to make the measurements.

air
Open ended manometer

-open end exposed to atmosphere (Po = atmosheric pressure)


h =10 cm Hg

N2

(reference for the open end is pressure of air (atmosphere)


- Measured pressure is relative pressure or gauge pressure

vacuum

h =86 cm Hg

Sealed end manometer


-sealed end is under vacuum (Po=0)
N2

(reference is complete vaccum where pressure = 0)


-measured pressure reading is absolute pressure

Pressure reading in an open-ended manometer is less than a (vacuum) sealed-end manometer..


Why?

Absolute Pressure: pressure measured relative to a fixed reference point of zero pressure,
in a vaccuum).
Gauge Pressure:

pressure measured relative to the atmosphere pressure.


(many pressure measurement devices measure only gauge pressure).

The relationship for converting between absolute pressure and gauge pressure is

Pabs Pgauge Patm


Value of Atmospheric pressure (Patmospheric)

- can vary with location, weather conditions and other factors

- can be thought of as the pressure at the base of a column of fluid (air) located at
the point of measurement (example, at sea level) (see figure below)

Actual Atmospheric pressure can be measured from a barometer (also called barometric pressure)
vacuum
Patm or Hatm
open to
atmosphere

Barometer measuring atmospheric


pressure
(Fluid usually water or mercury)

Absolute pressure is based on a complete vaccuum as reference, which is fixed and unchanged regardless of
location, weather or other factors.
Therefore, absolute pressure established a precise, invariable value that can be readily identified.
Relative pressure or gauge pressure is based on atmospheric pressure as reference, which varies with location,
weather and other conditions.
Therefore, when calculating absolute pressure from gauge pressure readings, the barometric pressure must
be noted.
Pabsolute = Pgauge + Patmospheric (measured by barometer)

In chemical engineering problems where the barometric pressure is not given, the value of Patmospheric may
be assumed as the value of standard atmospheric pressure.
HOWEVER, when using standard atmospheric pressure, one must always keep in mind, that this is an
assumption.
The values of standard atmospheric pressure in different units:

1.000

atmosphere (atm)

29.92

inches Hg

760.0

mm Hg

33.91

ft H2O

101.3

kPa

14.7

psi (lbf/ft2)

1.013 x 105

Pa

*** Values of standard atmospheric pressure can be used as conversion factors to convert pressure units

Pabsolute = Pgauge + Patmospheric


SUMMARY ON COMPUTATION OF ABSOLUTE PRESSURE FROM GAUGE PRESSURE IN CHEMICAL
ENGINEERING PROBLEMS
Ideally, the actual atmospheric pressure (obtained from a barometer reading, for example) is used to
calculate absolute pressure from above equation.
However, if the barometric pressure is not given, the value of standard atmospheric pressure could be
used as an assumption.
Other Notes
(a) If the pressure units are in psi, absolute P and gauge P are designated psia and psig, respectively.
(b) Vacuum pressure (absolute pressures < atmospheric) can be referred to as
negative gauge pressure or positive vacuum pressure.
example: - 1cm gauge pressure = +1cm vacuum pressure
If Pg= - 1 cm Hg,

Pabsolute= 76cm-1cm=75cm Hg

Practice Problem

The gauge pressure of a gas is -20 mmHg at a point where


atmospheric pressure is 755 mmHg. What is the absolute
pressure? What is the vacuum gauge pressure?
The pressure gauge on a tank of carbon dioxide used to fill
soda-water bottles reads 51.0 psi. At the same time, the
barometer reads 28 inHg. What is the absolute pressure in
psi?

FLUID PRESSURE MEASUREMENT


According to Perrys Chemical Engineers Handbook, pressure measurement devices may be
classified as:
(1) Elastic-element methods: example, Bordon tube
(2) Liquid-column methods: example, manometer

(3) Electrical methods: piezoelectric transducers, etc

Bordon Gauge
- hollow tube closed at one end and bent into a C-configuration
- open end is exposed to fluid to be measured

- as pressure increases or decreases, the tube tends to straighten or


curl, causing a pointer attached to a tube to rotate
- the position of the pointer on a calibrated dial gives the gauge
pressure of the fluid
- can measure fluid pressures from near vacuum to 700 atm

FLUID PRESSURE MEASUREMENT


Manometer
-used for more accurate measurement of pressures below 3 atm.
- U-shaped tube partially filled with a fluid of known density (manometer fluid)

- both ends of the tube are exposed to different pressures causing differences in
the level of the manometer fluid in both arms.
- the differences between pressures can be calculated from the measured
difference between the liquid levels of each arm.

FLUID PRESSURE MEASUREMENT


Manometer Types:
(1) Open-end manometer

- one end exposed to the fluid whose pressure is to be measured


- other end open to atmosphere

(2) Differential manometer

used to measure pressure differences between 2 points in a process


line

(3) Sealed-end manometer

-one end exposed to the fluid whose pressure is to be measured.


- other end is near vacuum.
(some of the enclosed fluid will vaporize in the empty space, and
prevents the existence of a perfect vacuum.)
Barometer: unsealed end of the manometer is exposed to atmosphere.

GENERAL MANOMETER EQUATION

General Manometer Equation


- A formula that relates the pressure difference (P =P1-P2) to the difference in the fluid levels (h)
- Based on the principle that the fluid pressure must be the same at any two points at the same height in a
continuous fluid. (in particular, the pressure at the height of the lower surface of a manometer fluid is
the same in both arms of the manometer)
At points A and B:

Pressure at A = Pressure at B

P1 1gd 1 P2 2 gd 2 f gh
Differential Manometer Equation
Fluids 1 and 2 are usually the same so that 1=2=

P1 P2 f g h

At points A and B:
Pressure at A = Pressure at B

P1 1gd 1 P2 2 gd 2 f gh

If either fluid 1 or fluid 2 is a gas at moderate pressure (i.e., on arm open to the atmosphere), the density
of the gas is 100 to 1,000 times lower than the density of the manometer fluid

Therefore the corresponding gd terms may be neglected

Manometer Formula for Gases


If both fluids are gases, then

Pressure difference (P) can also expressed as


head of manometer fluid

P1 P2 f gh
P f gh
1
P P1 P2
h
f g

Manometer Formula for Gases

P1 P2 f gh
P f gh

If both fluids are gases, then

Pressure difference (P) can also expressed as


head of manometer fluid

1
P P1 P2
h
f g

If P2 is open to atmosphere
(as in an open

ended manometer)

If P2 is at atmospheric pressure

P1 P2 f gh

An open-end

manometer

P1 Patm f gh

provides a direct
reading of ther
gauge pressure of a

Pgauge

f g

Pgauge

Pgauge f gh

gas

Manometer Formula for Gases

P1 P2 f gh
P f gh

If both fluids are gases, then

Pressure difference (P) can also expressed as


head of manometer fluid

1
P P1 P2
h
f g
If P2 is under vacuum

(as in an sealed

end manometer)

If P2 is at vaccum pressure

P1 P2 f gh

A sealed

end
manometer

P1 0 f gh

provides a direct
reading of the
absolute pressure of

Pabs

f g

Pabs

Pabs f gh

a gas

PROBLEMS
(1) A differential manometer is used to measure the drop in pressure between 2
points in a process line containing water. The specific gravity of the manometer
fluid is 1.05. The measured levels in each arm are shown below. Calculate the
pressure drop between points 1 and 2 in dynes/cm2. (g=980.7 cm/s2, density of
water is 1.00g/cm3)

PROBLEMS
(2) The pressure of gas being pulled through a line by a vacuum pump is
measured with an open end manometer. A reading of -2 inches is obtained.
What is the gauge pressure in inches Hg? What is the absolute pressure if Patm=
30 inches Hg?

CLASS DISMISSED

http://www.up.edu.ph/memorandum-no-paep-13-35-help-for-victims-of-typhoon-yolanda/

You might also like