TDS - Rheofinish 225 D

RHEOFINISH
225D
Water based chemical release agent
Description
A ready to use water based, safe, effective release agent
which is friendly to the environment. RHEOFINISH 225D is
applied to mould and shutter faces prior to casting concrete
in order to achieve a clean release. After removal of the
formwork, the resultant concrete has a smooth, hard,
uniform finish, with reduced incidence of blow holes.
RHEOFINISH 225D can be applied to the formwork by spray
in the form of a light uniform mist coating.
Primary uses
RHEOFINISH 225D is formulated for application to plywood,
timber, steel and plastic faced formwork and moulds, prior to
casting concrete, to ensure a clean release.
Action
RHEOFINISH 225D reacts chemically with cement to impart
excellent release properties to treated surfaces. Concrete
cast against surfaces coated with RHEOFINISH 225D
exhibit a smooth, hard, uniform finish.
RHEOFINISH 225D has no negative effect on the properties
of concrete nor will it impair the adhesion of subsequent
surface treatments when applied at the recommended
coverage rates.
Coverage
Packaging
RHEOFINISH 225D is available in 20 and 210 litre drums.
Bulk deliveries available upon request.
Typical properties*
Colour
SG finished product
Chloride content:
If after the first application, the RHEOFINISH 225D is

completely absorbed into new timber or plywood, a further
application should be made before filling the moulds or
formwork.
Milky liquid
0.971 at 25C
Nil
Composition
A chemically active release agent blended with water.
Directions for use

Apply before the first casting and thereafter re-apply
immediately after stripping and cleaning the mould.
Lightweight horticultural sprayers are ideal as RHEOFINISH
225D is finely atomised to give a uniform coating.
Excessive application should be avoided.
Alternatively, application may be made by a fine haired
brush, only a very thin coating should be made and any
excess removed.
The coverage rate for RHEOFINISH 225D is between 30 to

40m/litre when spray applied depending on smoothness
and porosity of the formwork used. Coverage is
considerably enhanced on marine ply and steel faced forms.
Note:
Progressively better results are obtained on plywood and
timber moulds as they become impregnated and the
operatives become accustomed to working with the release
agent. RHEOFINISH 225D in general, may be used over
timber moulds etc., which have been treated with other
mould oils, providing excess has been removed.
Equipment care
RHEOFINISH 225D may usually be left in spray guns or
sprayers without detriment, but with certain types, there may
be some softening of rubber seals with prolonged contact.
Storage
Store under cover, out of direct sunlight and protect from
extremes of temperature. Storage life up to 1 year when
stored in unopened containers as above. The product must
be stirred before being used.
Failure to comply with the recommended storage conditions
may result in premature deterioration of the product or
packaging. For specific storage advice consult Degussa's

Technical Services Department.
Safety precautions
As with all chemical products care should be taken during
use and storage to avoid contact with eyes and mouth.
Treat splashes to eyes and skin immediately. If accidentally
ingested, seek immediate medical attention. Keep away
from children and animals. Reseal containers after use.
Note
Field service, where provided, does not constitute
supervisory responsibility. For additional information contact
your local Degussa representative.
Degussa reserves the right to have the true cause of any
difficulty determined by accepted test methods.
Quality and care

All products originating from Degussas Dubai, UAE facility
are manufactured under a management system
independently certified to conform to the requirements of the
quality, environmental and occupational health & safety
standards ISO 9001, ISO 14001 and OHSAS 18001.
01/2000 Degussa-UAE revised 11/2003
* Properties listed are only for guidance and are not a guarantee of
performance.
Degussa Construction Chemicals UAE LLC

P.O. Box 37127, Dubai, UAE
Tel: +971 4 8851000
Fax: +971 4 8851002
www.degussa-cc.ae
e-mail: [email protected]
Whilst any information contained herein is true, accurate and

represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or
distributors, as the conditions of use and the competence of any labour
involved in the application are beyond our control.
Certificate No.
963680
As all Degussa technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
Certificate No.
945787
Certificate No.
772556

TDS - Rheofinish 225 D

Uploaded by

Copyright:

Available Formats

TDS - Rheofinish 225 D

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS - Rheofinish 225 D

Uploaded by

Copyright:

Available Formats

RHEOFINISH

If after the first application, the RHEOFINISH 225D is

Directions for use

The coverage rate for RHEOFINISH 225D is between 30 to

packaging. For specific storage advice consult Degussa's

Quality and care

Degussa Construction Chemicals UAE LLC

Fax: +971 4 8851002

Whilst any information contained herein is true, accurate and

You might also like