TDS - Emaco S88 Plus

EMACO S88
PLUS
A dimensionally compatible and durable
polymer fibre reinforced, thixotropic
repair mortar
Description
EMACO S88 PLUS, is a cementitious pre-bagged readyto-use structural repair mortar in powder form. When
mixed with the correct amount of water, it produces a
thixotropic, high strength repair mortar, reinforced with
acrylic polymer fibres. It possess excellent bond
characteristics to steel reinforcement and to concrete.
EMACO S88 PLUS mortar is shrinkage compensated. It
has low permeability and is extremely durable. EMACO
S88 PLUS contains no metallic aggregate and is chloride
free.
EMACO S88 PLUS is formulated for sprayed or trowelled
applications, in thicknesses up to 50 mm in one layer by
hand application. Greater thicknesses can be achieved
when spray applied.
Typical applications
All types of structural repair which can be applied by

trowel or wet spray.
Repair of structural members subjected to repetitive
loading.
Repairs to reinforced or pre-stressed beams or
columns.
Protection of concrete subject to attack from water
containing chlorides and sulphates etc.
Repairs in industrial areas, especially those
containing mineral oils, lubricants.
Repairs in marine environments.
Advantages
Shrinkage compensation - reduces the risk of

cracking due to shrinkage and ensures full contact
with host concrete and load transfer in structural
repair situations.
No primer required - allows rapid application at
reduced cost.
Can be spray applied - rapid application of large
quantities.
Low rebound - when spray applied rebound is
minimal, with subsequent saving in material cost.
Extremely low permeability - gives excellent
resistance to attack by aggressive elements.
Packaging
EMACO S88 PLUS is available in 25kg bags.
Typical properties*
Appearance:
Grey powder containing

micro fine fibres
approx. 2280 kg/m
3 days >55N/mm
28 days > 70 N/mm
<4%
<10%
Plastic density:
Compressive strength at 20C BS
1881 : Part 116:
Water absorption ASTM C642-97
Volume of permeable voids ASTM
C642-97
Porosity Rilem CPC11.3
<10%
Water penetration BS EN 12390
<10mm
Part 8 : 2000
Drying shrinkage @28 days ASTM
<500 microstrains
C157 : 93
When tested @ 2.375 litres water addition for 25kg powder
Application procedure
Preparation of substrate:
It is essential that the substrate to be repaired is sound,
clean and free of all contamination.
The damaged areas of concrete to be removed should be
clearly identified. The perimeter of the area should be
saw cut to a depth of 10 mm and the edges cut as neatly
as possible keeping the sides square. Feather-edging is
not permitted and a minimum thickness of 10 mm must
be maintained over the whole repair area.
The substrate should be prepared to provide a rough
surface having at least a 5 mm amplitude at 20 mm
frequency.
If unsound or contaminated concrete is found to extend
beyond the premarked area, consult the engineer in
charge. Subject to his approval cut out as necessary
back to clean sound concrete.
If reinforcement is corroded ensure that the back of the
steel has been exposed. Reinforcement should have all
rust removed by the use of power tools, abrasive blasting
(wet or dry) or wire brushing. Reinforcing steel should be
exposed and cleaned around its whole circumference.
Steel should be prepared to Swedish Standard SIS 05900:1967-SA 2 or BS 4232 Ref. 24 second quality.
Extra protection to the reinforcement can be provided by
use of CONCRESIVE ZR dependant upon the
circumstances of use and requirement of the client.
Severely corroded reinforcement may require
replacement and the engineer must be consulted.
Water saturation:
Thoroughly saturate the surface of the concrete to
provide a saturated surface dry condition. Poor quality
concrete may require soaking for a significant length of
time. Any surface water should be removed using an oil
free compressed airjet.
Mixing:
EMACO S88 PLUS must be mixed mechanically. The
following mixing equipment is suitable, heavy duty slow
speed drill with spiral mixing paddle, forced action mixer,
such as Creteangle, Mixal, Pan Mixers etc. Mixers
attached to spray units such as Meyco Deguna or
Putzmeister are suitable.
The specified amount of water to obtain the desired
consistency can be slightly varied according to site
conditions but should not exceed 2.5 litres per 25kg bag.
Start the mixer and add the EMACO S88 PLUS powder
rapidly and continuously. Mix for 3 minutes after all the
powder has been added until mortar is homogeneous
and lump free.
Add water, if necessary, within the limits given, until the
required consistency is achieved. Mix for a further 1-2
minutes. The amount of water required will be affected
by ambient temperature and relative humidity.
EMACO S88 PLUS can be used when the ambient
temperature is between 5 and 50C. If ambient
temperature is >30C, use chilled water and condition the
bagged product in an air-conditioned store prior to use.
Maximum mixed temperature should be no more than
35C.
Application:
After mixing, EMACO S88 PLUS can be sprayed or
trowel applied. Suitable spraying units are Meyco
Deguna 20, Turbosol T20 and Putzmeister P11.
P.O. Box 37127, Dubai, UAE

Tel: +971 4 8851000
www.degussa-cc.ae
Fax: +971 4 8851002

e-mail: [email protected]
Coverage:
One 25kg bag of EMACO S88 PLUS with 2.375 litres of
added water will yield approximately 12.0 litres of mortar
which will cover 1m at 12.0 mm average thickness.
Note: In addition to shrinkage compensation, this
product has been designed to develop tensile strength
sufficient to withstand the internal stress generated by
volume change to reduce the incidence of drying
shrinkage cracking.
Storage
Store out of direct sunlight, clear of the ground on pallets,
protect from rainfall. Avoid excessive compaction. Shelf
life is 12 months when stored as above.
Safety precautions
As with other products containing Portland cement, the
cementitious material in EMACO S88 PLUS grout may
cause irritation. In case of contact with eyes, immediately
flush with plenty of water for at least 15 minutes. Call a
physician. In case of contact with skin, wash skin
thoroughly.
Note
Field service, where provided, does not constitute
supervisory responsibility. For additional information
contact your local Degussa representative.
Degussa reserves the right to have the true cause of any
difficulty determined by accepted test methods.
Quality and care
When applying by hand EMACO S88 PLUS must be

forced tightly into the substrate to ensure intimate contact
with the pre-wetted substrate.
Levelling and initial finishing should be carried using a
wooden or plastic float.
Final finishing should be carried out using a steel float.
When the material has stiffened to the point where finger
pressure lightly marks the surface, a final firm trowelling
should be given using the steel float.
Degussa Construction Chemicals UAE LLC
Curing:
Good curing is essential. Particular care is required in
hot and/or windy conditions. Curing can either be with a
single coat of MASTERKURE 181 curing membrane,
which is compatible with most subsequent protective
coatings, or by covering the work with plastic sheet fixed
over wet hessian or wet foam rubber.
All products originating from Degussas Dubai, UAE

facility are manufactured under a management system
independently certified to conform to the requirements of
the quality, environmental and occupational health &
safety standards ISO 9001, ISO 14001 and OHSAS
18001.
06/2003 Degussa-UAE revised 02/2005
* Properties listed are only for guidance and are not a guarantee
of performance.
Whilst any information contained herein is true, accurate and

represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or
distributors, as the conditions of use and the competence of any labour
involved in the application are beyond our control.
Certificate No.
963680
As all Degussa technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
Certificate No.
945787
Certificate No.
772556

TDS - Emaco S88 Plus

Uploaded by

Copyright:

Available Formats

TDS - Emaco S88 Plus

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS - Emaco S88 Plus

Uploaded by

Copyright:

Available Formats

EMACO S88

All types of structural repair which can be applied by

Shrinkage compensation - reduces the risk of

Grey powder containing

P.O. Box 37127, Dubai, UAE

Fax: +971 4 8851002

Quality and care

When applying by hand EMACO S88 PLUS must be

Degussa Construction Chemicals UAE LLC

All products originating from Degussas Dubai, UAE

Whilst any information contained herein is true, accurate and

You might also like