NTS Mcqs Paper of Assistant Engineer Operations

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 15

NTS Mcqs Paper of Assistant Engineer Operations MEPCO

1. power factor? Answer: true power/apparent power


2. To reduce cost of power generation?
Answer: Load factor(higher/increase)+Diversity factor(higher increase)
3. An Ideal voltage source has internal resistance
Answer: 0 Resistance
4. An Ideal current source has internal resistance
Answer: Resistance
5. ____ is defined as the measure of instrument by which it is error free
A. Accuracy
B. Precision
C. Resolution
6. Electrical lines of force about a negative charge are
A. Circular, anticlockwise
B. Circular, clockwise
C. Radial, inward
D. Radial, outward
Answer: C
7. A _____ meter is used a null detector in wheatstone bridge
A. Ammeter
B. Voltmeter
C. Galvanometer
Answer: voltemeter
8. A moving iron ammeter coil has few turns of thick wire in order to have:
A. Low resistance
B. High sentivity
C. Effective damping
D. Large scale
Answer: A
9. A permanent magnet coil meter has which features
A. Low power consumption
B. no hysteresis loss
C. reduced eddy current
D. reduced damping
E. all
10. A digital signal is what in
A. Dicrete
B. Discrete in time
C. Discrete in amplitude
D. Discrete in neather time nor amplitude
E. Discrete in both amplitude and time
Answer: E
11. The EM field and current are concentrated close to the surface of the conductor. The
phenomenon is called?
Answer: Skin Effect
12. The wavelength of an EM wave after reflection at an angle on a surface
Answer: Increases in the actual direction of propagation
13. When electric field is parallel to the plane of incidence, the electromagnetic wave is said to be
Answer: Parallel polarized
14. x H = J + D is Maxwell equation
15. Bucholz relay is used in Transformer Protection
16. Gates between following range reffered by MSI
17. Gates between following range reffered by LSI
18. Which type of system is referred by pneumatic system
A. Pressure
B. Hydraulic

C. Fluid
19. Solid grounding is used for voltages
a. above 220 kV
b. above 11 kV
c. below 660 V
d. below 115 V
Answer: C
20. Cross over distortion is
Answer: Class B
21. The channel of a JFET is between the
A. Gate and drain
B. Drain and source
C. Gate and source
D. Input and output
Answer: B
22. Velocity saturation in MOSFET is
23. Which type of engine uses maximum air fuel ratio
A. Petrol engine
B. Gas engine
C. Diesel engine
D. Gas turbine
E. Hydro turbine
24. If ROC (Region of Convergence) does not converge
25. Transfer function is
A. Mathematical model
B. System with no physical structure
C. Can be calculated through differential equations
26. In LTI system is characterized by
A. Impulse input
B. Step input
27. When the current decreases to 2% the power in bulb decrease to
28. Question about Convolution
29. Which bulb operates on lowest power
A. Night bulb
B. Neon bulb
C. GLS bulb
D. Torch lamp
Answer: D
30. Which thing happens in gas discharge lamps
Answer: Ionization in vapor or gas
31. Continuous signal in the time domain in frequency domain
32. Superposition theorem relates to
33. Which of the following relay is used in Motor for protection
Answer: Thermal relay
34. Kilowatt hour is the unit of
Answer: Energy
35. In z transform cos pi/4 is the period is equal to
36. What will be the sampling frequency that reveals the same sampled signal
37. Which transistors are used in TTL? Bipolar
38. Which system used dc to dc high voltage gain
A. Solar system
B. Battery backup
39. Which statement is false for switching regulators
40. To decrease the power in control system we use
41. Power plant the availability of power is least for
A. Wind
B. Solar
C. Tidal

D. Geothermal
E. Bio gass
42. A diode that has a negative resistance characteristics is the
A. Schottkey diode
B. Tunnel diode
C. Hot-carrier diode
D. Laser diode
E. Zener Diode
Answer: B
43. Common mode rejection ratio is the ratio of
Answer: Differential mode gain to Common Mode gain
44. Resolution of ADC is defined as the no of bits in
Answer: Output
45. The control system is used for
46. Horizontal line in the s plane is for
47. Recharge able batteries are called? Secondary batteries
48. The batteries which are charged and discharged continuously
49. Which system needs more stability
A. Automatic washing machine
B. Traffic signal system
C. Home heating system
D. Motor with position control
50. Natural frequency in the control system represents
51. For measuring small resistance we use
Answer: Kelvin bridge
52. Hay bridge is used for the measurement of
Answer: Inductance
53. ____ bridge used for the measurement of resistance
Answer: Wheatstone bridge
54. In three phase 4 wire system how many voltages are available
Answer: Two
55. _____ acts as voltage controlled variable capacitor
Answer: Varactor
56. By which a meter after checking with no current returns to its previous state
Answer: Controlling Torque
57. By connecting a shunt of higher value in ammeter what will decrease
Answer: Current sensitivity decreases
58. If z transform lies in ROC then
A. System is stable
B. Inverse of system is stable
C. Both system and its inverse are unstable
D. Both system and its inverse are stable
59. If R1 is the resistance of a coil of copper at t oC and RT is the resistance at T oC and also the
resistance temperature coefficient of copper per degree centrigrade at 0oC is 1/234.45, then Rt/RT
(A) (1+t) / (1+T)
(B) (1+ 234.45t) / (1+234.45 T)
(C) (234.45 + t) / (234.45 + T)
(D) (234.45 + t2 ) / (234.45 + T 2).
60. The shunt winding of a motor has a resistance of 85 ohm at 22oC. When the motor runs at full
load, its resistance increases to 100 ohms. The resistance temperature coefficient of winding per
0oC is 0.004. The rise in temperature of the winding will be nearly
(A) 20oC
(B) 50oC
(C)70oC
(D) 100oC.
61. Wimbledon Tournament is for? Lawn Tennis

62. All organizations share


63. For minimum input a person has got the output he has used the resources
efficiently
64. Sharjah is in? UAE
65. Against Nehrus Report Qaid-e-Azam proposed a solution of how many points? Answer: 14
points
66. the punishment for robbery in Islam
67. on simple series question (___, 15, 19, 24,) answer 12
68. Which of the following Rukn-e-Islam is called a shield? Answer: Fasting
69. What is the literal meaning of word Qiblah? Answer: In front of
70. Northern end of Pakistan is occupied by western range of which of following? Answer:
Himalayan range
71. The ancient name of IRAN
72. TLRIA is to WOULD then YBVLKA is for? BEYOND
73. Which word will be in the middle select and tick that one
A. Rigorous
B. Retrospective
C. Remove
D. Revive
E. rumor
74. on 6th September India attacked
75. Washington DC is called ____ (City of Magnificent Distance)

Home / Study & Jobs / General Knowledge / Electrical MCQS sample for GENCO Junior
Engineer NTS Test

Electrical MCQS sample for GENCO Junior


Engineer NTS Test
Electrical MCQS sample for GENCO Junior Engineer NTS Test solved on
www.pakknowledge.com.

Electrical MCQS sample for GENCO Junior


Engineer NTS Test
Alternator

A synchronous machine
1.
2.
3.
4.

can operate at unity power factor.


can operate at leading power factor.
can operate at lagging power factor.
can operate at any power factor.

Symmetrical waveform does not having

1.
2.
3.

capacitance.
odd harmonics.
both even and odd harmonics.

4.

1.
2.
3.
4.

1.
2.
3.
4.

even harmonics.
A winding is having number of slots is equal to number of poles, then this winding is
called
concentrated winding.
short pitch winding.
full pitch winding.
distributed winding.
A winding is having number of slots is greater than number of poles, then this
winding is called
concentrated winding.
distributed winding.
full pitch winding.
integrated slot winding.

When the number of slots / pole / phase is fractional, then this winding is called

1.
2.
3.
4.

short pitch winding.


full pitch winding.
fractional slot winding.
integral slot winding.

When the number of slots / pole / phase is integer, then this winding is called

1.
2.
3.
4.

fractional slot winding.


integer slot winding.
concentrated winding.
short pitch winding.

Which alternator are more suitable for high-speed system?

1.
Salient pole.
2.
Non-salient pole.
3
Both (A) and (B).
4. None of these.

The number of poles in turbo alternator are

1.
2.
3.
4.

2.
6.
8.
10.

1.
2.
3.
4.

When two alternator are operating in parallel and at perfect synchronization, their
synchronizing power will be
negative.
infinite.
positive.
zero.


1.
2.
3.
4

1.
2.
3.
4.

1.
2.
3.
4.

The stationary alternator must not be connected to live bus bars because it will results
_______________ .
short circuit.
open circuit.
nothing will happen.
floating.
Floating of alternators with busbars occurs at when
synchronized generated emf is less than the busbar voltage.
synchronized generated emf is greater than the busbar voltage.
synchronized generated emf is equal to the busbar voltage.
none of above.
Which of following conditions is to be fulfilled, for connecting an alternator to
infinite bus?
Phase sequence should be same.
Frequency is need not same.
Terminal voltage of alternator need not to be same with existing bus.
None of above.

If a slot consists of one coil side then the winding is called

1.
2.
3.
4.

double layer winding.


full pitch winding.
single layer winding.
short pitch winding.

If the slot consists 2 coil sides of different coils is called

1.
2.
3.
4.

double layer winding.


single layer winding.
concentric winding.
distributed winding.

Distributed winding and short chording employed in AC machine will result in

1.
2.
3.
4.

increase in emf and reduction in harmonics.


decrease in emf and increase in harmonics.
increase in both.
decrease in both.

What is the distribution factor for a 108 slot, 12 pole, 3 winding?

1.
2.
3.
4.

0.88.
0.96.
0.92.
1.

Fifth harmonic component of the induced voltage in three phase AC generator can be
eliminated by using a winding pitch of

1.
2.
3.
4.

2 / 3.
4 / 5.
5 / 6.
6 / 7.

The pitch of arc with 96 stator slots and 6 pole is

1.
2.
3.
4.

36.
48.
32.
16.

Factors on which frequency of alternator depends upon

1.
2.
3.
4.

number of poles and synchronous speed.


number of poles and rotor speed.
synchronous speed.
independent of any factors.

Which of the following is not determined by circle diagram?

1.
2.
3.
4.

Power factor.
Frequency.
Efficiency.
Output.

To determine the losses of an alternator is driven by

1.
2.
3.
4.

synchronous motor.
compensated DC motor.
calibrated DC motor.
AC series motor.

1.
2.
3.
4.

The distribution factor for a 36 slots, 4 poles, single layer three phase winding
alternator will be.
0.98.
0.96.
0.35.
0.20.

Cooling of synchronous generator is done by

1.
2.
3.
4.

air cooling.
direct water cooling.
hydrogen cooling.
all of these.

Calculate the highest speed at which 50 Hz alternator can operate

1.
2.
3.

6000 rpm.
3000 rpm.
3000 rps.

4.

1.
2.
3.
4.

none of the above.


If two mechanically coupled alternator deliver power at 50 KHz and 60 KHz
respectively. Then highest speed of the alternator is
3600 rpm.
4000 rpm.
600 rpm.
500 rpm.

National Testing Service


NTS Sample Paper Of
ENGINEERING
National Testing Service NTS Sample Paper of ENGINEERING

SAMPLE PAPER ENGINEERING

ENGLISH

Complete the sentences by choosing the most appropriate option, from the given lettered
choices (A to D) below each.

1. 1.
1.
2.
3.
4.

A.
B.
C.
D.

Sensory cells _______ impulses by producing electrical signals.


responding
to respond
respond to
respond

Each question below consists of a related pair of words, followed by five lettered pairs of
words. Select the lettered pair that best expresses a relationship similar to that expressed
in the original pair.

1. 2.
1.
2.
3.
4.
5.

A.
B.
C.
D.
E.

1. 3.
1.
2.
3.
4.
5.

A.
B.
C.
D.
E.

ENZYME: CATALYST::
vaccine: allergy
bacterium: microbe
gland: muscle
vein: organ
neuron: corpuscle
HORNS: BULL::
mane: lion
wattles: turkey
antlers: stag
hoofs: horse
wings: eagle

Choose the lettered word or phrase that is most nearly opposite in meaning to the word in
capital letters.

1. 4.
1.
2.
3.
4.

A.
B.
C.
D.

TRANSIENT:
temporary
shining
dull
permanent

Questions 5-8 are based on the following passage.

Although the schooling of fish is a familiar form of animal social behavior, how the school
is formed and maintained is only beginning to be understood in detail. It had been thought
that each fish maintains its position chiefly by means of vision. Our work has shown that,
as each fish maintains its position, the lateral line, an organ sensitive to transitory
changes in water displacement, is as important as vision. In each species a fish has a
preferred distance and angle from its nearest neighbor. The ideal separation and
bearing, however, are not maintained rigidly. The result is a probabilistic arrangement that
appears like a random aggregation. The tendency of the fish to remain at the preferred
distance and angle, however, serves to maintain the structure. Each fish, having
established its position, uses its eyes and its lateral lines simultaneously to measure the
speed of all the other fish in the school. It then adjusts its own speed to match a weighted
average that emphasizes the contribution of nearby fish.
1. 5. According to the passage, the structure of a fish school is
dependent upon which of the following?
1. A.
2. B.
from
3. C.
4. D.
1. 6.
1.
2.
3.
4.

A.
B.
C.
D.

rigidly formed random aggregations


the tendency of each fish to remain at a preferred distance
neighboring fish
measurements of a weighted average by individual fish
both B & C

The word its in the passage refers to the


school of fish
fish
organs
structure

1. 7. The author of the passage believes that the structure of fish


schools is maintained through
1.
2.
3.
4.

A.
B.
C.
D.

vision only
lateral lines only
the eyes and lateral lines simultaneously
an organ not yet discovered

1. 8. The passage suggests that, after establishing its position in


the school formation, an individual fish will subsequently
1. A.
maintain its preferred position primarily by visual and
auditory means

2. B.
make continuous sensory readjustments to its position
within the school
3. C.
make unexpected shifts in position only if threatened by
external danger
4. D.
surrender its ability to make quick, instinctive judgments
ANALYTICAL REASONING

Questions 9-12

Each body spray made by a manufacturer is a mixture of two or more essences selected
from a stock of exactly five different essences labeled F, G, H, J and K. The manufacturer
has learned that a formula for a body spray is acceptable if and only if it does not violate
any of the rules listed below.

If the body spray contains F, it must also contain H and there must be twice as much H as
F.
If the body spray contains G, it must also contain J and the amount of J must equal the
amount of G.
H cannot be used in combination with J.
J cannot be used in combination with K.
If the body spray contains K, the amount of K must be greater than the total amount of the
other essence or essences used.

1. 9. Which of the following is an acceptable formula for a body


spray?
1.
2.
3.
4.
5.

A.
B.
C.
D.
E.

Four parts J, four parts G


Five parts K, five parts G
One part F, one part K
Two parts G, two parts F
Three parts H, three parts F

10. The addition of more H could make which of the following formulas for body sprays
acceptable?

1. A.
2. B.

Two parts G, one part H, four parts K


Two parts H, one part J, three parts K

3. C.
4. D.
5. E.

One part F, one part H, five parts K


Two parts F, two parts H, two parts K
One part G, one part H, one part K

11. Which of the following could be added to an unacceptable body spray consisting of
two parts H and one part K to make it acceptable?

1.
2.
3.
4.
5.

A.
B.
C.
D.
E.

Two parts H
One part J
Two parts K
One part F
One part G

12. Each of the following is a pair of essences that can be used together in an acceptable
body spray consisting of two or more essences EXCEPT:

1. A.
G and J
2. B.
K and H
3. C.
F and G
4. D.
F and H
5. E.
F and K
The football coach at Government College, Faisalabad noticed that some of his players
were frequently late to morning football practices and seemed somewhat lethargic after
they did arrive. He directed his assistant coach to look into the matter. The assistant
coach reported back that most of the late and less active players belonged to fraternities
on campus which were renowned for their frequent and late-night parties. The head coach
then prohibited all of his football players from being members of fraternities. He reported
that this would ensure that his players would get to practice on time and that they would
have more productive practice sessions.

13. The head coachs reasoning is not sound because he fails to establish which one of
the following?

1. A.
He fails to establish a system to monitor his players
fraternity membership and to impose penalties for those who do
not follow his new rule.
2. B.
He fails to establish that his players are physically big and
strong enough to be successful football players.
3. C.
He fails to establish that his new policy will ensure that at
least some of his football players will go to bed at a more
reasonable hour.

4. D.
He fails to establish that his best football players did not
belong to fraternities anyway.
5. E.
He fails to establish that the success of them fraternity
system will not suffer if the football players are precluded from
becoming members.

CURRENT AFFAIRS

14. Who is the present Chief Justice of Pakistan?

1.
2.
3.
4.

A.
B.
C.
D.

Irshad Hasan Khan


Nazim Hussain Siddique
Iftikhar Mohammad Chaudhry
Sheikh Riaz Ahmad

15. Who is the President of USA?

1.
2.
3.
4.

A.
B.
C.
D.

Barack Obama
Condoleezza Rice
Nancy Reagan
Hillary Clinton

SUBJECT

16. ________ are fixed stations that enable wireless devices to communicate with a landbased transmission network within a given range.

1.
2.
3.
4.

A.
B.
C.
D.

BTS
MS
BSS
BSC

17. FFT stands for:

1.
2.
3.
4.

A.
B.
C.
D.

Frequency Fast transmission


Frequency Fourier transmission
Fast Fourier transmission
Fast Frequency transmission

18. The value of most nearly is:

1.
2.
3.
4.

A.
B.
C.
D.

-5.9399
-1.980
0.31402
5.99178

19. Wireless access network is defined as?

1. A.
A network in which data is transmitted using fiber optic
medium.
2. B.
A network in which data is transmitted using radio signals
instead of cables.
3. C.
A network in which data is transmitted using Digital
Subscriber Line.
4. D.
All of the above

ANSWER KEYS

Q #.

Right Choice

10

11

12

13

14

15

16

17

18

19

You might also like