OPERATION & MAINTENANCE

MANUAL
for
END SUCTION TYPE PUMPS
PATTERSON PUMP COMPANY

A SUBSIDIARY OF THE GORMAN-RUPP COMPANY

PO Box 790
9201 Ayersville Road
Toccoa, Georgia 30577
Telephone: 706-886-2101

SAFETY PRECAUTIONS
WARNING
Do not operate this equipment in excess of its rated speed or other than in accordance with the
instructions contained in this manual.
The equipment has been found satisfactory of the conditions for which it was sold, but its operation in
excess of these conditions may subject it to stresses and strains which it was not designed to withstand.
For equipment covered by this instruction book, it is important to observe safety precautions to protect
personnel from possible injury. Among the many considerations, personnel should be instructed to:

avoid contact with rotating parts

avoid bypassing or rendering inoperative any safeguards or protective devices
avoid extended exposure in close proximity to machinery with high noise levels
use proper care and procedures in handling, lifting, installing, operating and maintaining the
equipment
do not modify this equipment consult factory if modification is deemed necessary
do not substitute for repair parts which can be provided by the equipment manufacturer.

Safe maintenance practices with qualified personnel are imperative.

Failure to heed this warning may result in an accident causing personal injury.

TABLE OF CONTENTS
SECTION I:

General Information ................................................................................1

SECTION II:

Storage & Protection...............................................................................1

SECTION III:

Installation
3-1 Location..............................................................................................2
3-2 Foundation .........................................................................................2
3-3 Mounting.............................................................................................2
3-4 Alignment ...........................................................................................2
3-5 Grouting..............................................................................................6
3-6 Piping..................................................................................................7

SECTION IV:

Operation
4-1 Starting ...............................................................................................9
4-2 Shutdown ...........................................................................................9
4-3 Minimum Flow Limitation..................................................................10

SECTION V:

Maintenance
5-1 Lubrication........................................................................................10
5-2 Stuffing Box ......................................................................................11
5-3 Wear Ring Clearance .......................................................................12

SECTION VI:

Repairs & Replacement

6-1 To Remove Rotor .............................................................................15
6-2 Disassembly of Rotating Element ....................................................15
6-3 Inspection .........................................................................................16
6-4 Assembly ..........................................................................................16
Locating Operation Difficulties ...................................................... 19-20
Recommended Spare Parts..................................................................21

SECTION I
GENERAL INFORMATION
This manual covers the installation, operation and maintenance of Patterson Pump end suction pumps.
The pump is a centrifugal, single stage, single suction type. When properly installed and when given
reasonable care and maintenance, centrifugal pumps should operate satisfactorily for a long period of
time. Centrifugal pumps use the centrifugal force principal of accelerating the liquid within a rotating
impeller, and then collecting it and converting it to pressure head in a stationary volute.
The pump consists of two assemblies:
1.

Volute assembly or stationary part

2.

Rotating element or moving part

The back pullout design casing allows removal of the impeller and rotating element without disturbing
suction and discharge piping.
The volute cover collects stuffing box leakage, which may be drained using the drilled and tapped hole
provided. Discharge flange is drilled and tapped for gauge connection. The pump volute is drilled and
tapped on the underneath side for drainage of the pump. Wear rings are provided in the casing to
minimize internal bypassing of the liquid being pumped and to improve efficiency.
SECTION II
STORAGE & PROTECTION
All pumps are shop serviced and ready for operation when delivered, but there is occasions when
considerable time elapses between the delivery date and the time the pump is put into operation.
Equipment, which is not in service, should be kept in a clean, dry area. If equipment is to be stored for
long periods of time (six months or more), the following precautions should be taken to insure that the
equipment remains in good condition.
1.

Be sure that the bearings are fully lubricated.

2.

Unpainted-machined surfaces, which are subject to corrosion, should be protected by

some corrosive resistant coating.

3.

The shaft should be rotated 10 to 15 revolutions by hand periodically in order to spread

the lubricant over all the bearing surfaces. Suitable intervals are from one to three
months, depending on atmospheric conditions, etc. In order to insure that the pump shaft
does not begin to sag, do not leave the shaft in the same position each time.

4.

Space heaters on motors and controllers should be connected and fully operable if
atmospheric conditions approach those experienced in operation. Consult instruction
manuals for other precautions concerning storage of individual components of pumping
unit.

5.

Fresh lubricant must be applied to bearings upon removal of equipment form storage.

SECTION III
INSTALLATION
3-1

Location:

Several factors should be considered when selecting a location for the pumping unit (pump, base, drive,
and coupling). The unit should be accessible for both inspection and maintenance. Headroom should be
provided for the use of crane, hoist or other necessary lifting devices. The pump should be located as
close as possible to the liquid supply so that the suction line is short and direct. Location should require a
minimum of elbows and fittings in the discharge line to minimize friction losses. The unit should be
protected against flooding.
3-2

Foundation:

The foundation should be sufficiently substantial to absorb vibration and to form a permanent rigid
support for the base plate. Concrete is most widely used for foundation. Before pouring the foundation,
locate anchor bolts per outline drawing. Allow for 3/4 inch to 1 1/2 inch of grout between foundation and
base plate. The top surface of the foundation should be roughened to provide a good bond for the grout.
3-3

Mounting:

WARNING!!! Do not attempt to lift entire unit using lugs provided on either pump or motor only. Such
action may lead to failure of the lugs and possible damage to the unit or injury to personnel. Lift unit with
slings around the base plate, or by attaching cables to the lifting lugs on both the pump and the motor.
Coupling halves should be disconnected when mounting the pumping unit on the foundation. Wedges
should be used to support the unit at the time of grouting. Wedges should be located adjacent to anchor
bolts (one on each side of bolt) and midway between bolts. Adjust the wedges to raise or lower the unit
as required to align suction and discharge flanges to piping and to level the base plate. Leveling bolts
made of cap screws and nuts are useful when leveling large base plate, but should not replace shims or
blocks for supporting the load. After unit has been in operation for about a week, check alignment. After
making any required adjustments, dowel pump and motor to base.
3-4

Alignment:

The pump unit has been manufactured to allow field alignment. The unit must be properly aligned at the
time of installation. Reliable trouble-free and efficient operation of a unit depends upon correct alignment.
Misalignment may be the cause of noisy pump operation, vibration, premature bearing failure, or
excessive coupling wear. Factors that may change the alignment of the pumping unit are settling of the
foundation, springing of the base plate, piping strains, a shift of the pump or drive on the foundation.
When checking coupling alignment, remember flexible couplings are not intended to be used as universal
joints. The purpose of a flexible coupling is to compensate for temperature changes and to permit end
movement of the shafts without interference with each other.
Two types of misalignment may exist: parallel misalignment and angular misalignment. Limits of
misalignments are stated in the coupling manufacturer's instructions, but should be kept to a minimum for
maximum life of equipment components.

Section III Alignment Continued

To check coupling alignment, the following procedure should be followed:
1.

Set the coupling gap to the dimension shown on the outline drawing.

2.

Check for parallel misalignment by placing a straight edge across both coupling halves at
four points 90 apart. Correct alignment occurs when the straight edge is level across the
coupling halves at all points.

3.

Check angular misalignment with a feeler gauge at four points 90 apart. Correct
alignment occurs when the same gauge just enters between the halves at all four points.

Angular and parallel misalignment are corrected by shifting the motor and adding or removing shims from
under the motor feet. After each change, it is necessary to recheck the alignment of the coupling halves.
Adjustment in one direction may disturb adjustment already made in another direction.
An alternative method for checking coupling alignment is by use of a dial indicator. Proceed as follows:
1.

Scribe index lines on coupling halves or mark where the indicator point rests.

2.

Set indicator dial to zero.

3.

Slowly turn both coupling halves so that the index lines match, or the indicator point is
always on the mark.

4.

Observe dial reading to determine whether adjustments are needed. Acceptable

alignment occurs when total indicator reading does not exceed 0.004 inches for both
parallel and angular alignment.

The importance of correct alignment cannot be overemphasized.

corrected as required after:
1.
2.
3.
4.
5.

Mounting
Grouting has hardened
Foundation bolts are tightened
Piping is connected
Pump, driver, or base plate is moved for any reason.

Alignment should be checked and

WARNING!!!
The importance of correct alignment cannot be overemphasized. The following procedure should be
used for initial installation.
1.

Place complete pump assembly on anchor bolts allowing room under the base plate for leveling
wedges or shims. Make sure the base plate is level by using the leveling wedges adjacent to the
foundation bolts and midway between the bolts.

2.

Put nuts on the anchor bolts and tighten evenly, but not too tight.

3.

At this point check alignment of the coupling. This should not be more than that recommended
by the coupling manufacturer.

4.

If misalignment is evident, determine which direction the coupling needs to be moved.

5.

Loosen all nuts and add the shims underneath the base plate at the opposite corners. Use the
anchor bolts to flex the base plate to bring the coupling into alignment.

6.

After the alignment has been made with all anchor bolt nuts tight, the grouting can take place.

7.

After grouting is completed, final alignment should be checked to be sure it is within allowable
tolerances. Use of shims under the driver can be used to obtain final alignment.

Alignment should be checked and corrected as required after:

-

Mounting
Foundation bolts are tightened
Grouting has hardened
Piping is connected
Pump, driver, or base plate is moved for any reason

3-5

Grouting:

Grout compensates for unevenness in the foundation and distributes the weight of the unit uniformly on
the foundation. It also prevents lateral shifting of the base plate and reduces vibration. Use a nonshrinking grout. Foundation bolts should be tightened evenly, but not too firmly. Grout the unit as follows:
1.

Build a strong form around the base plate to contain the grout.

2.

Soak the foundation top thoroughly, and then remove surface water.

3.

Pour grout. Tamp liberally while pouring in order to fill all cavities and prevent air
pockets. The space between the foundation and base plate should be completely filled
with grout. In order to prevent the base plate from shifting, fill under the base plate at
least four inches in from all four edges. Wedges may be left in place.

4.

After the grout has hardened (usually about 48 hours), thoroughly tighten foundation bolts
and check alignment.

5.

Approximately 14 days after the grout has been poured or when it is thoroughly dry, apply
an oil base paint to exposed edges of the grout to prevent air and moisture form coming
in contact with the grout.

3-6

Piping:

Connect pipelines after the grout has thoroughly hardened. The suction and discharge piping should be
installed with the shortest and most direct runs. Elbows should preferably be of the long radius type.
Pipes must line up naturally. The piping must never be pulled into position by the flange bolts. Such
action may draw the pump out of alignment. Pipes should be support independently of the pump so as
not to put any strain on the pump casing. Suction piping, if not properly installed, is a potential source of
faulty operation. Suction lines should be free of air leads, and arranged so there are no loops or high
spots in which air can be trapped. Generally, the suction line is larger than the pump suction nozzle, and
eccentric reducers should be used. Eccentric reducers are not necessary for bottom suction pumps. If
the liquid supply is located below the pump centerline, the reducer should be installed with the straight
side up.
Most often air enters the suction pipe entrained in the liquid. Installations with a static suction lift
preferably should have the inlet of the vertical suction piping submerged in the liquid to four times the
piping diameter. A large suction pipe will usually prevent the formation of vortexes or whirlpools,
especially if the entrance is flared (Figure 5). A floating vortex breaker (raft) around the suction piping
may be provided if a tendency appears for a vortex to form at the liquid surface. A stream of liquid falling
into the sump near the intake pipe will churn air into the liquid (Figure 6). The supply line should extend
down into the sump. Liquid supply entering a well perpendicular to the intake line tends to rotate the
liquid, which interferes with the flow into the suction line (Figure 7). A baffle placed in front of the supply
pipe will remedy this situation. A short elbow should never to bolted directly to the pumps suction nozzle.
The disturbance in the flow caused by the sharp bend so near the pump inlet may result in noisy
operation, loss in efficiency, and capacity, and heavy end thrust.
A long sweep or long radius elbow placed as far away from the pump as practicable should be used if a
bend is necessary in the suction line. If separate suction lines cannot be used for each pump, then a
tapering header with Y-branches should be used (Figure 8A). A straight branch header should never be
used. Prior to installing the pump, suction piping and pump should be inspected internally, cleaned and
flushed. If a strainer is installed in the suction line, the openings in the screen must be checked and
cleaned periodically. The opening must be smaller than the sphere size allowed by the impeller.
Discharge piping should be installed with check valve and gate valve, with the check valve being between
the pump and the gate valve. The check valve prevents reverse flow and protects the pump from
excessive backpressure. The gate valve is used to isolate the pump for maintenance, priming and
starting. If a diffuser is used, it should be placed between the pump and check valve.
Stuffing box seal connections are usually made form the top of the pump casing. If the liquid being
pumped is unsuitable for sealing, then it is preferable to bring fresh, cool water to seal connections from
an outside source. Centrifugal separators or other filters may be used to remove abrasive particles from
the liquid being pumped if an outside source is not available. After all piping connections have been
made, the alignment should be checked again.
SECTION IV
OPERATION
Before bolting the coupling halves together, check the drive rotation to see that it matches the pump
rotation. Pump rotation is indicated by an arrow attached to the casing assembly. For a three-phase
motor, rotation may be reversed, if necessary, by interchanging any two of the three power leads.
Rotation of single-phase motors is fixed by internal wiring.
WARNING!!! Prior to startup, check the coupling alignment as covered in the Installation Section.
Operation of the pump with the unit misaligned will cause damage to the shaft, bearings, and the
coupling.

Section IV Operation Continued:

4-1

Starting:

When possible, turn the pump shaft by hand to insure that the parts do not bind

Check the bearing lubricant

Open the valve in the pump suction line, if fitted

Close discharge valve

Prime the pump in one of the following ways:

1. If the pump operates under positive pressure, open vent valve on top of the pump casing.
After all entrained air has escaped, close the vent valves. Rotate the shaft, if possible, to
allow any air trapped in the impeller passages to escape.
2. If the pump operates on a suction lift and a foot valve is included in the system, fill the
pump and the suction line with liquid from an outside source. Trapped air should be
allowed to escape through the vent valve while filling.
3. If the pump operates on a suction lift and no foot valve is provided, use a vacuum pump
or ejector operated by air, steam, water, etc. to evacuate air from the pump case and
suction line by connecting the ejector to the priming connection on top of the pump case.

Open valves in stuffing box seal lines, if fitted. Start driver. Open discharge valve slowly when the pump
is up to speed.
CAUTION: Overheating and/or loss of prime will result if the pump is operated against a closed valve for
more than a few minutes.
WARNING !!! The coupling guard should be in place when the unit is started. Stay clear of any exposed
rotating parts while the pump is operating. Contact with rotating parts may result in injury to personnel.
Adjust the packing gland until there is a slight leakage from the stuffing box. (See Maintenance on
Adjustment of Packing). Mechanical seals need no adjustment. There should be no leakage.
NOTE: Should the pump fail to build up pressure or discharge water when the discharge valve is
opened, stop the pump and read Section Locating Operating Difficulties.
4-2

Shutdown

The pump may be stopped with the discharge valve open without causing damage. However, in order to
prevent water hammer effects, the discharge valve should be closed first.
1.

Close discharge valve.

2.

Stop driver.

3.

Close water seal valves.

4.

Close valve in the pump suction line, if fitted. If danger of freezing exists, drain the pump
completely.

4-3

Minimum Flow Limitation

All centrifugal pumps have limitations on the minimum flow at which they should be operated. The most
common limitation is to avoid excessive temperature buildup in the pump because of absorption of the
input power into the pumped fluid. Other less understood reasons for restrictions are:
1.

Increased radial reaction at low flows in single volute casings.

2.

Increased NPSHR at low flows.

3.

Noisy, rough operation and possible physical damage due to internal recirculation.

4.

Increased suction and discharge pulsation levels.

The size of the pump, the energy absorbed, and the liquid pumped are among the considerations in
determining these minimum flow limitations. For example, most small pumps such as domestic home
circulators, service water pumps, and chemical pumps have no limitations, except for temperature buildup
considerations while many large, high horsepower pumps have limitations as high as 40-50% of the best
efficiency point capacity. The minimum safe flow for this pump is given under Pump Specifications.
SECTION V
MAINTENANCE
5-1

Lubrication:

Couplings:

Couplings with rubber drive elements do not require lubrication. Most other couplings
require some form of lubrication.
Consult manufacturer's instructions for
recommendations.

Bearings:

Frequency of lubrication depends upon operating conditions and environment, therefore,

lubrication intervals must be determined by experience. Table I may be used as a
general guide for grease relubrication. Lubricants need replacing only because of
contamination by dirt or dust, metal particles, moisture or high temperature breakdown.
A small amount of grease may be added about every 400 hours of operation. The
bearing housing should be about 1/3 full of grease. Oil lubricated units are provided with
constant level oilers. Bottles should be kept filled at all times so that there is a visible
supply of oil. All lubricants have a tendency to deteriorate in the course of time,
therefore, sooner or later it will be necessary to replace the old lubricant with new.
Bearings, which are dismantled, are, of course, much more easily cleaned than bearings,
which stay in assembled equipment. Solvents may be used more freely and effectively.
For cleaning bearings without dismounting, hot light oil at 180 - 200 F may be flushed
through the housing while the shaft is slowly rotated. Light transformer oils, spindle oils,
or automotive flushing oils are suitable for cleaning bearings, but anything heavier than
light motor oil (SAE 10) is not recommended. The use of chlorinated solvents of any kind
is not recommended in bearing cleaning.

Grease Relubrication: (pumps are shipped with grease in bearing housings)

1.

Thoroughly clean grease fitting and outside of bearing housing.

2.

Remove drain plug.

3.

Inject clean, new grease forcing out the old.

4.

Start and run the pump for a short time to eject any excess grease.

5.

Wipe off all excess grease and replace drain plug.

10

WARNING !!! Proper lubrication is essential to the pump operation. Do not operate the pump if sufficient
lubricant is not present in the bearing housing of if lubricant is contaminated with excessive dirt or
moisture. Operation of the unit under these conditions will lead to impaired pump performance, and
possible bearing failure. Do not operate the pump with excessive amount of lubricant. Such action will
cause bearings to overheat.
5-2

Stuffing Box:

The purpose of a stuffing box is to limit or eliminate leakage of the pump fluid and to prevent air from
entering the suction spaces along the pump shaft. Pumps are equipped with packing (limited leakage) or
mechanical seals (no leakage). Normally, the pumped liquid is used to lubricate the stuffing box seal. If
the liquid is dirty, gritty, or contains material that would gum or jam the seal, use a sealing liquid from an
external source. If suction pressure is above atmospheric pressure, seal piping may not be required. For
pumps equipped with packing, there must always be a slight leakage from the glands. The amount of
leakage is hard to define, but we recommend a steady dripping of liquid through the gland. Stuffing box
glands should be adjusted after the pump is started. When leakage is excessive, tighten gland bolts
evenly a little at a time. Allow an interval for packing to adjust to new position. Never tighten gland to be
leakproof, as this will cause overheating and undue wear on shaft sleeves.
Replace stuffing box packing as follows:
1.

Shutdown the pump.

2.

Take precautions to prevent the driver from being inadvertently started.

3.

Remove the gland bolt nuts and gland.

4.

Remove and discard old packing rings note location of lantern ring. When repacking
stuffing box, lantern ring must be positioned such that the water seal connection is
opposite lantern ring.

5.

Clean out the stuffing box.

6.

Inspect shaft sleeve for wear if it is scored or grooved, it should be replaced.

7.

Make sure the stuffing box bushing (if furnished) is set at the bottom of the box.

8.

Insert rings of packing and tap lightly to seat against bushing. Be sure rings are of the
proper size and length and installed with cuts staggered. Lantern ring must be installed
opposite sealing water connection.

9.

Install gland and tighten, finger tight. With the pump running, adjust gland as described
previously. Care should be taken during the first hour of operation to take up on the
packing gradually just enough to maintain the required amount of leakage.

If the pump is operated daily, the stuffing box packing should be renewed about every two to three
months before it gets hard and scores the shaft sleeves.
Mechanical seals should be removed, assembled, and/or adjusted according to the seal manufacturer's
instructions. There should be no leakage from the gland if mechanical seals are used, except for a brief
run in period.

11

5-3

Wear Ring Clearance:

Running fits between wear rings is given under the pump specifications. When these clearances are
doubled, or the capacity of the pump is reduced by 5 to 10%, the rings should be renewed. The purpose
of these rings is to keep internal bypassing of the liquid being pumped to a minimum. Clearances should
be checked periodically and whenever the pump casing is opened. Check with feeler gauge or by direct
measurement. Measure ID of case ring and OD of impeller ring, then compute clearance (ID minus OD).
Diametral clearance for the 4 x 3 x 11 AAES and the 5 x 3 x 11 AES is .012 - .014 inches and .016 - .018
inches respectively.

12

13
Slow

200F
(93C)
120F
(49C)
200F
(93C)
200F
(93C)

120F
(49C)
0F
(-18C)
120F
(49C)
0F
(-18C)

1 to 8 weeks

1 to 4 weeks grease at
shutdown

1 to 8 weeks

1 to 4 weeks

120F
(49C)
200F
(93C)
+250F
(121C)

250F
(121C)
300F
(149C)

-20F
(-29C)
100F
(38C)

-65F
(-54C)

80F
(27C)
80F
(27C)

1 to 8 weeks

200F
(93C)

1 to 8 weeks

1 to 4 weeks grease at
shutdowns

Daily flushing out dirt

1 to 7 days

1 to 4 weeks

1 to 2 months

2 to 6 months

SUGGESTED
GREASING
INTERVALS**

0F
(-18C)

200F
(93C)

120F
(49C)

0F
(-18C)

32F
(0C)

High

Low

BEARING OPERATING
TEMPERATURE

Synthetic type greases

Good quality high

temperature type greases

Wide temperature range

Diester-type greases
(Silicone-DiesterPolyester lubricants)

Channeling (high speed)

type grease

High viscosity lubrication

Lithium or other corrosion

control grease

High quality NGLI

No. 1 or 2 multipurpose
bearing greases are
generally satisfactory.
Consultation with a
reputable lubricant
supplier is recommended.

USE THESE GREASES

**Suggested starting interval for maintenance program. Check grease conditions for oiliness and dirt and adjust greasing frequency accordingly.
Watch operating temperatures as sudden rises may show need for grease or indicate over lubrication on higher speed applications.

Light

Dry

Slow to
medium

Clean to dirty

Slow to
medium

Light to
heavy

Light to
medium

High speed

Light

Dry

Slow

Heavy to
very heavy

Clean to
moderate

Possible frost

Light to
heavy

High humidity
Direct water
Splash
Slow to
medium

Slow to
medium

Light to
medium

Extreme dirt

Dry

Dry

Moderate
to dirty

Slow to
medium

Light to
medium

Slow to
medium

Dry

Clean

Speed

Load

OPERATING
CONDITIONS

Light to
medium

Moisture

Dirt

AMBIENT
CONDITIONS

TABLE 1
SUGGESTED RE-LUBRICATION INTERVALS FOR VARIOUS
ENVIRONMENTAL, OPERATING AND TEMPERATURE CONDTIONS
(GREASE LUBRICATED BEARINGS)

TABLE II
RECOMMENDED GREASES

Use NLGI Grade 2 grease

Such As:

WARNING!!!

COMPANY

GREASE

Chevron

SRI

CITGO

Premium Lithium EP2

Exxon

Lidok EP2

Keystone

81EP2

Pennzoil

PennLith 712

Shell

Alvania EP2

Texaco

Multifak EP2

Use of lubricants other than those listed or their equivalent will cause reduced pump
performance and reduce bearing life.

14

SECTION VI
REPAIRS AND REPLACEMENT
WARNING!!! Whenever any disassembly work is to be done on the pump, disconnect the power source
to the driver to eliminate any possibility of starting unit.
6-1

To Remove Rotor:

Reference: Pump Assembly Section

6-2

1.

Remove the coupling guard and disconnect coupling halves.

2.

Remove bolts holding the motor to the base and other connections, then remove the
motor from the base. CAUTION: Refer to the motor instructions.

3.

Disconnect any piping from the volute (1) that will interfere with the removal of the volute
cover (71).

4.

Remove bolting from the bearing housing (19) to the base, volute support (53) to the
base and bolting from the volute cover (71) to the volute (1).

5.

Pull entire rotating assembly and bearing housing assembly from the volute. The
assembly should be pulled straight out until the impeller (2) is clear of the volute (1).

Disassembly of Rotating Element:

1.

Remove impeller screw (102) and the washer (24).

2.

Remove the impeller (2). DO NOT LOSE IMPELLER KEY (32).

3.

Remove packing gland (17).

4.

Remove bolting form between the volute cover (71) and the bearing housing (19).

5.

Remove volute cover (71) from the bearing housing (19) assembly.

6.

Packing rings (13), lantern ring (29) and shaft sleeve (14) with o-ring (38) can be
removed.

7.

Remove deflector (40).

8.

Remove pump half of coupling.

9.

Remove bolts from the bearing cover (37) and remove bearing cover (17) and lip seal
(49).

10.

Pull shaft (6) and bearings (16 & 18) from bearing housing (19).

11.

Remove bearing locknut (22) and washer.

12.

Remove bearing (16 & 18).

15

6-3

Inspection:

Visually inspect parts for damage affecting serviceability. Check o-rings and gaskets for cracks, nicks, or
tears; packing rings for excessive compression, fraying or shredding, and embedded particles. Replace if
defective in any way. Mount the shaft between lathe centers and check eccentricity throughout the entire
length. Eccentricity should not exceed .002 inches. Bearing surfaces should be smooth and shoulders
square and free of nicks.
Measure OD of impeller hub or impeller wear rings and ID of casing wear ring. Compute diametral
clearance (ID minus OD) and compare with clearance given under the pump specifications. Surfaces
must be smooth and concentric. Examine impeller passages for cracks, dents or embedded material.
Examine shaft sleeves for wear.
6-4

Assembly:

Assembly is the reverse of the disassembly procedure.

reassembling the pump:

The following should prove helpful in

1.

All parts, inside and out, should be clean. Dirt and grit will cause excessive wear, plus needless
shutdown.

2.

Make certain that the keys are in their proper position.

3.

New o-ring, gaskets, and lip seals should be used when reassembling the pumps.

4.

Insure that the packing does not block seal water inlet.

5.

Rotate by hand to insure that the parts do not bind before installing in the volute (1).

6.

Bearing mounting is simplified by heating the whole bearing, thereby expanding it enough to be
slipped on the shaft. This heating is best done by submerging the bearing in a bath consisting of
10 15% soluble oil in water and heated to boiling. This mixture cannot be overheated, is nonflammable, drains off easily permitting convenient handling, yet leaves an oil film sufficient for
rust protection of the bearing surfaces.

16

TABLE IV
BEARING DEFECTS
(Failures Replace if found)
DEFECT (failure)

APPEARANCE

Flaking and cracking

In the early stages the surface of

the inner and outer races
develop small cracks, which
flake. The cracks and flaking
ultimately spread over the entire
race surface.

PROBABLE CAUSE
1. Normal fatigue failure.
2. Bearing loads in excess of
bearing capacity caused by
misalignment.
1. Dirt in the bearings.

Indentations

Indentations or cavities in the

inner and outer races.

2. Excessive impact loading of

the bearings such as
improper mounting or
removal.
1. Poor lubrication.

Broken separator (cage)

Cracked separator or separator

in pieces.

2. Misalignment of shaft.
3. Excessive shaft deflection.
1. Fit on shaft or in housing too
loose.

Wear

Bore and OD of outer ring of

bearing galled or braided.

Fractured ring

Hairline cracks or complete ring

fracture.

2. Bearing locked by dirt and

turning on shaft or in
housing.
1. Forcing a cocked bearing on
or off a shaft.
2. Too heavy a press fit.

Discoloration

Balls and races darker than

normal appearances of bearing
metal. (Moderate discoloration of
balls and races not a reason for
discard).

1. Inadequate lubrication.

1. Water entering the housing.

Corrosion

Balls and raceways rusted.

2. Condensation inside the

housing.
3. Lubricant breaks down into
acid (wrong lubricant).

18

LOCATING OPERATING DIFFICULTIES

In the majority of cases, operating difficulties are external to the pump and the following causes should be
carefully investigated before undertaking repairs:
No Water Delivered

Pump not primed indicated by no pressure on discharge.

Speed too low indicated by low pressure on discharge.

Valve closed indicated by high discharge head.

Impeller completely plugged up indicated by low discharge pressure.

Abnormally Small Quantities Delivered

Air leaks in suction pipe or stuffing boxes.

Speed too low.

Discharge head higher than anticipated.

Impeller partially plugged up.

Obstruction in suction line.

Mechanical defects: casing rings worn, impeller damaged, casing or seal defective.

Insufficient Pressure

Speed too low. Might be caused by low voltage or current characteristics different from
nameplate reading on the motor.

Air in water will cause the pump to make a cracking noise.

Mechanical defects: worn casing rings, damaged impeller, defective casing or seal.

Intermittent Operation

Leaky suction line.

Water seal plugged (hence, a leaky stuffing box).

Suction lift too high.

Air, gas or vapor in liquid.

19

Pump Overloads Driver

Speed too high.

Head lower than rated, hence, pumping too much water. (This is valid for low specific speed
pumps).

Mechanical defects: stuffing boxes too tight, shaft bent, rotating element binds.

Rubbing due to foreign matter in the pump between the case rings and the impeller.

Pump Vibrates

Misalignment.

Foundation not sufficiently rigid.

Impeller partially clogged.

Mechanical defects: bent shaft, rotating element binds, bearings worn, coupling defective.

Suction and discharge pipes not anchored.

Pump cavitating from too high a suction lift.

Air entrainment in the pump suction due to low submergence.

20

RECOMMENDED SPARE PARTS FOR END SUCTION PUMPS

Reference: Assembly Section
INTERMITTENT DUTY
Number
13
13A
14
25
65
80

Description
*

Packing (stuffing box)

Packing O-Ring (shaft sleeve)
* Shaft Sleeve
Casing Ring
+* Mechanical Seal (stationary element)
+* Mechanical Seal (rotating element)
Coupling and its accessories (not shown)
Gasket (not shown)
Gland Bolts (not shown)

CONTINUOUS DUTY
Number
2
6
13
13A
14
16
18
22
25
32
40
46
65
68
80
102

Description
*
*
*

+*
+*
*

Impeller
Shaft
Packing (stuffing box)
Packing O-Ring (shaft sleeve)
Shaft Sleeve
Bearing (inboard)
Bearing (outboard)
Bearing Locknut
Casing Ring
Impeller Key
Deflector
Coupling Key
Mechanical Seal Stationary Element
Shaft Collar
Mechanical Seal Rotating Element
Impeller Screw
Coupling and its accessories (not shown)
All Hardware (not shown)
Gasket (not shown)
Gland Bolts (not shown)

* Determined by Pump Construction

+ Complete Consists of 65 & 80

21