Scribd
Upload
1K views3 pages

Mazak t2

This document provides information about RS232 support and settings for transferring programs between a PC and Mazak T2 CNC machine. It lists the CNC parameters and PC DNC settings required. Steps are outlined for transferring both EIA and Mazatrol programs from the CNC to the PC and from the PC to the CNC. A hardware handshake cable diagram and additional notes are also included.

Uploaded by

hung
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views3 pages

Mazak t2

This document provides information about RS232 support and settings for transferring programs between a PC and Mazak T2 CNC machine. It lists the CNC parameters and PC DNC settings required. Steps are outlined for transferring both EIA and Mazatrol programs from the CNC to the PC and from the PC to the CNC. A hardware handshake cable diagram and additional notes are also included.

Uploaded by

hung
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

RS232 Support

CNC: Mazak T2
CNC Parameters
A15 - 206 (No parity, 2 stop bits, 8 data bits)
A16 - 1 (RS232 parameter for serial tape?)
A17 - 6 (CMT baud rate 4800)
A18 - 6 (EIA baud rate 4800)
A19 - 0 (Tape rewind code)
A20 - 1 (Output ISO)
A21 - 0 (Spaces between work # & data
A22 - 0 (Spaces between programs)
A23 - 0 (Leader / trailer in feet)
A24 - 0 (Tape Vertical Parity Check = off)
A29 bit 0 - 0 (Don't stop at O or :)
A29 bit 1 - 1 (Stop at M02)
A30 bit 0 - 1 (Serial reader on)
A30 bit 1 - 1 (Serial punch on)
A30 bit 2 - 0 (Parallel reader off)
A30 bit 3 - 0 (Parallel punch off)
Remember: Bit 0 is the RIGHTmost bit
A31 - 109 ("#" code for EIA punch)
A32 - 70 (":" code for EIA punch

PC DNC Settings
Baud: 4800
Code: 7 data bits / ASCII Even
Stop Bits: 2
EOB: CR/LF
Handshaking: XON/XOFF
ADVANCED
Leader: %CRLF
Trailer: %
Skip lines which contain: %

Additional Notes
Note: The transfer of Mazatrol programs with CMT IO requires
PC-DNC plus 3.3.1 or later.
When transferring to / from this CNC, it is recommended that
you use a hardware handshake cable. Diagram:
PC 9-pin to CNC 25-pin:
PC(2) to CNC(2)
PC(3) to CNC(3)
PC(7) to CNC(5)


PC(8) to CNC(4)
PC(5) to CNC(7)
Jumper 6,8,20 on CNC side only
Attach cable shield to pin 1 on CNC side only

RS232 Support

PC 25-pin to CNC 25-pin:


PC(2) to CNC(3)
PC(3) to CNC(2)
PC(4) to CNC(5)
PC(5) to CNC(4)
PC(7) to CNC(7)
Jumper 6,8,20 on CNC side only
Attach cable shield to pin 1 on CNC side only

Steps for transferring CNC to PC (EIA programs):


EIA.1 Press PROGRAM softkey
EIA.2 Press PROGRAM FILE softkey
EIA.3 Press DATA IN OUT softkey
EIA.4 Press TAPE I/O softkey
EIA.5 Press PUNCH NC TAPE softkey
EIA.6 Enter work #
EIA.7 Press INPUT
EIA.8 Repeat 6/7 for addl. Work #'s
EIA.9 Press START
Steps for transferring CNC to PC (Mazatrol programs):
MAZ.1 Press PROGRAM softkey
MAZ.2 Press PROGRAM FILE softkey
MAZ.3 Press DATA IN OUT softkey
MAZ.4 Press CMT I/O softkey
MAZ.5 Press SAVE CMT softkey
MAZ.6 Enter work #
MAZ.7 Press INPUT
MAZ.8 Repeat 6/7 for addl. Work #'s
MAZ.9 Press START
Steps for transferring PC to CNC (EIA programs):
EIA.1 Press PROGRAM softkey
EIA.2 Press PROGRAM FILE softkey
EIA.3 Press DATA IN OUT softkey
EIA.4 Press TAPE I/O softkey
EIA.5 Press ALL LOAD NC<-TAPE
EIA.6 Press START
Steps for transferring PC to CNC (Mazatrol programs):
MAZ.1 Press PROGRAM softkey


MAZ.2
MAZ.3
MAZ.4
MAZ.5
MAZ.6
MAZ.7
MAZ.8

RS232 Support
Press
Press
Press
Press
Enter
Press
Press

PROGRAM FILE softkey


DATA IN OUT softkey
CMT I/O softkey
LOAD CMT softkey
work #
INPUT
START

Tip: To avoid keying in program #'s for Mazatrol input, use the
DATA IO -> CMT -> CMT CONTENTS function to load file
contents onto the screen. Then select LOAD NC <- CMT and
click START. Values will remain filled in for you.
Steps for setting parameters in the CNC:
1 Press LEFT PAGE key
2 Press PARAM softkey
3 Cursor to parameter
4 Key in new value
5 Press INPUT
6 POWER DOWN CNC

You might also like