AQ 09 12 FAN Service Manual PDF

SPLIT-TYPE AIR CONDITIONER
Basic : AQ12FA
Model : AQ12FA
AQ09FA
AS12FAXFA
AS12FBAXAP
Model Code : AQ12FAN/AQ12FAX
AQ09FAN/AQ09FAX
AS12FANXFA/AS12FAXXFA
AS12FBANXAP/AS12FBAXXAP
SERVICE
Manual
AIR CONDITIONER
AQ12FAN/AQ12FANSER/AS12FANXFA/AS12FBANXAP
THE FEATURE OF PRODUCT
Good Morning Mode
Catechin Filter
Silver Nano Evaporator
Deodorizing Filter
Anti-Bacterial Cross Fan
AQ12FAX/AQ12FAXSER/AS12FAXXFA/AS12FBAXXAP
For more information, Please access to our service web site(http://itself.sec.samsung.co.kr)
Operating Instructions and Installation
Contents
11. Precautions ................................................................................................................................................... 1-1
1-1 Installing the air conditioner ...................................................................................................................
1-1
1-2 Power supply and circuit breaker ..........................................................................................................
1-1
1-3 During operation
........................................................................................................................................
1-1
1-4 Disposing of the unit .................................................................................................................................
1-2
1-5 Others .............................................................................................................................................................
1-2
12. Product Specifications ........................................................................................................................ 2-1

2-1 The Feature of Product
.............................................................................................................................
2-1
2-2 Product Specifications
..............................................................................................................................
2-2
2-3 The Comparative Specifications of Product .......................................................................................
2-4
2-4 Accessory and Option Specifications ...................................................................................................
2-5
13. Alignment and Adjustments ......................................................................................................... 3-1

3-1 Test Mode ......................................................................................................................................................
3-1
3-2 Error Mode and Check Method ..............................................................................................................
3-3
3-3 Setting Option Setup Method ................................................................................................................
3-7
14. Disassembly and Reassembly ...................................................................................................... 4-1

4-1 Indoor Unit ....................................................................................................................................................
4-1
4-2 Outdoor Unit
4-4
...............................................................................................................................................
15. Exploded Views and Parts List ..................................................................................................... 5-1

5-1 Indoor Unit ....................................................................................................................................................
5-1
5-2 Outdoor Unit ................................................................................................................................................
5-5
5-3 Assy Control In ............................................................................................................................................
5-9
16. Electrical Parts List

17. Wiring Diagram
.................................................................................................................................
6-1
........................................................................................................................................
7-1
18. Schematic Diagram
...............................................................................................................................
8-1
19. Circuit Descriptions ............................................................................................................................... 9-1

9-1 PCB Circuit Descriptions ...........................................................................................................................
9-1
9-2 Refrigerating Cycle Diagram ...................................................................................................................
9-2
Samsung Electronics
Contents
10. PCB Diagram ................................................................................................................................................ 10-1
11. Operating Instructions ....................................................................................................................... 11-1
11-1 Name of Each Part .................................................................................................................................... 11-1
11-2 Main Function
...........................................................................................................................................
11-3
11-3 Wireless Remote Control-Buttons and Display ............................................................................... 11-5
12. Troubleshooting ...................................................................................................................................... 12-1

12-1 Basic Breakdown Diagnosis Items ....................................................................................................... 12-1
12-2 Trouble check in the initial status......................................................................................................... 12-2
12-3 Breakdown diagnosis by symptoms ................................................................................................... 12-3
12-4 PCB Inspection Method .......................................................................................................................... 12-10
12-5 Main Part Inspection Method................................................................................................................ 12-12
13. Block Diagram ............................................................................................................................................ 13-1

14. Reference Sheet ........................................................................................................................................ 14-1
14-1 Index for Model Name ............................................................................................................................ 14-1
14-2 Refrigerant Pressure during the Charging
14-3 Pressure & Capacity mark
.......................................................................................
14-2
......................................................................................................................
14-2
14-4 Q & A for Non-trouble ............................................................................................................................. 14-3

14-5 Cleaning/Filter Change ........................................................................................................................... 14-6
14-6 Installation .................................................................................................................................................. 14-8
14-7 Installation Diagram of Indoor Unit and Outdoor Unit ................................................................ 14-9
Samsung Electronics
2. Product Specifications
2-1 The Feature of Product
Good Morning Mode
Catechin Filter
Catechin, extracted from the green tea, is contained in the filter and deactivates captured bacteria and unpleasant odors.
Silver Nano Evaporator
Deodorizing Filter
Activated carbon is incorporated in the filter, efficiently absorbing cigarette smoke, pet odors, and other unpleasant smells, replacing
them with clean, refreshing air.
Anti-Bacterial Cross Fan
Samsung Electronics
2-1
2-2 Product Specifications

Model
Item
AQ12FA
INDOOR UNIT
Type
Cooling/Heating(ISO)
COOLING/HEATING(SASO)
Dehumidifying
Perfor- Air volume
mance
Noise
EER
AS12FAXFA
OUTDOOR UNIT
INDOOR UNIT
OUTDOOR UNIT
WALL-MOUNTED
WALL-MOUNTED
KW
3.5/3.8
3.5
BTU/h
KCAL
l/h
1.2
1.2
Cooling
m3/min(H/
M/L)
10.2/8.3/6.1
17
10.2/8.3/6.1
17
Cooling
Db(H/L)
41
54
41
54
COOLING/HEATING(ISO)
POWER
POWER
CONSUMPTION
OPERATING
CURRENT
W/W
2.82/3.22
2.73
BTU/WH
BTU/WH
PH-V-HZ
1-220/240-50
1-220/240-50
1240/1180
1280
6.2/5.3
5.8
Power POWER FACTOR COOLING
86.96/96.80
95.95
STARTING CURRENT
21
21
5.5
5.5
25
25
LENGTH
POWER CORD
NUMBER OF CORE WIRRE

CAPACITY
mm
Outer Dimension WxHxD

Weight(Net)
Refrigerant
825285189
660475242
Kg
8.4
30
8.4
26
mmxL(m)
6.357.5
6.357.5
Gas
mmxL(m)
12.77.5
12.77.5
DxL(m)
182
182
Rotary G4B129JXAEL
Rotary 44D124DXAEL
induction Moter(PSC)
13000
12400
POE(FREOL68ES-T)
SUNISO.4GSD/NOC
Moter
Type
Rated Output
Oil Type
Type
Blower
720548265
inch
Type
Compressor
825285189
Liquid
Drain Hose
Size
Motor
Type
Rated Output
Heat exchanger
Refrigerant Control Unit
Cross-flow
Propeller
Cross-flow
Propeller
Resin/steel
Steel
Resin/steel
Steel
37
58
37
58
2ROW 14STEP
1ROW 20STEP
2ROW 14STEP
1ROW 18STEP
Capillary tube
Capillary tube
Freezer Oil Capacity
cc
360
450
Refrigerant to changer
R410A,920g
R22,700g
INLET
INLET
Protection Device(OLP)
Cooling Test Condition
INDOOR UNIT:DB27C/WB19C OUTDOOR UNIT:DB35C WB 24C
Maximum Operation Condition
2-2
Samsung Electronics
Model
Item
AQ12FASER
INDOOR UNIT
Type
Cooling/Heating(ISO)
Dehumidifying
Perfor- Air volume
mance
Noise
EER
AS12FBAXAP
OUTDOOR UNIT
INDOOR UNIT
OUTDOOR UNIT
WALL-MOUNTED
WALL-MOUNTED
KW
3.5/3.8
BTU/h
12000/13000
12000
KCAL
3500
l/h
1.2
1.2
Cooling
m3/min(H/
M/L)
10.2/8.3/6.1
17
10.2/8.3/6.1
25
Cooling
Db(H/L)
41
54
41
54
POWER
POWER
CONSUMPTION
OPERATING
CURRENT
W/W
2.78/3.3
2.7
BTU/WH
9.48/11.30
8.7
BTU/WH
PH-V-HZ
1-220/240-60
1-220-60
1260/1150
1300
5.8/5.3
Power POWER FACTOR COOLING
94.4
98.48
STARTING CURRENT
21
21
5.5
5.5
LENGTH
POWER CORD
NUMBER OF CORE WIRRE

CAPACITY
Outer Dimension WxHxD

Weight(Net)
Refrigerant
825285189
660475242
inch
Kg
8.4
30
8.4
26
mmxL(m)
6.35*5.0
6.35*5.0
Gas
mmxL(m)
12.7*5.0
12.7*5.0
DxL(m)
18*2
18*2
Rotary 44D129MXAEL-DO
Rotary 44B135IXAEL
12730
13400
Moter
Type
Rated Output
Oil Type
NOC & Suniso-4GSD

Type
Blower
25
720548265
Type
Compressor
25
825285189
Liquid
Drain Hose
Size
A
mm
Motor
Type
Rated Output
Heat exchanger
Refrigerant Control Unit
NOC & Suniso-4GSD
Cross-flow
Propeller
Cross-flow
Propeller
Resin/steel
Steel
Resin/steel
Steel
30
58
30
58
2ROW 14STEP
1ROW 20STEP
2ROW 14STEP
1ROW 18STEP
Capillary tube
Capillary tube
Freezer Oil Capacity
cc
450
360
Refrigerant to changer(R22)
830
600
INLET
INLET
Protection Device(OLP)
Cooling Test Condition
Maximum Operation Condition
Samsung Electronics
2-3
2-3 The Comparative Specifications of Product

AQ12FA
AQ12FASER
Item
AS12FAXFA
AS12FBAXAP
Indoor Unit
Design
Outdoor Unit
Net Weight
Outer Dimension
(WidthxHeightxDepth)
Indoor Unit
Outdoor Unit
33.8kg
Indoor Unit
Outdoor Unit
Outdoor Unit
Air Purifying System
Indoor Display
Filter
29.0kg
1,080x315x205mm
720x548x265mm
Indoor Unit
Noise
2-4
8.4kg
660x475x242mm
36dB
47dB
47dB
Silver Nano Filter
Catechin Filter
Deodorizing Filter
LED
Samsung Electronics
2-4 Accessory and Option Specifications

2-4-1 Accessories
Item
Descriptions
Code-No.
Q'TY
Installation Plate
DB97-02851B
DB93-03170M
(H/P)
Remark
Remote Control
DB93-03170N
(C/O)
Batteries for Remote Control
DB47-90024A
Owners Manual
Installation Manual
Indoor
Unit
TIONS
OWNER'S INSTRUC
INSTRUCCIONES
MANUAL DE
PER L'USO
ISTRUZIONIINSTRU
ES
MANUAL DE ATION
MANUEL D'UTILISEISUNG
GEBRAUCHSANW
Air ConditionerSplit
Splut-type Room
domstico sistema
ad unit Separate
Aire acondicionado
d'aria per ambienti
Split
Condizionatorede ar condicionado tipo
Aparelho
type spar
Climatiseur de
e
Geteilte raumklimaanlag
TIONS
OWNER'S INSTRUC
INSTRUCCIONES
MANUAL DE
PER L'USO
ISTRUZIONIINSTRU
ES
MANUAL DE ATION
MANUEL D'UTILISEISUNG
GEBRAUCHSANW
Air ConditionerSplit
Splut-type Room
domstico sistema
ad unit Separate
Aire acondicionado
d'aria per ambienti
Split
Condizionatorede ar condicionado tipo
Aparelho
type spar
Climatiseur de
e
Geteilte raumklimaanlag
3-wire Assembly Cable

(18)
5-wire Assembly Cable

(24)
Outdoor
Unit
Drain Plug
DB67-20011A
Rubber Leg
DB73-20134A
Assembly Pipe, 6.35mm
DB62-02672D
1
Accessory
Box

(09)
Samsung Electronics
DB62-02672G
2-5
Product Specifications
Accessories(cont.)
Item
Descriptions
Code-No.
Q'TY
DB62-02672H
Vinyl Tape, Width 80mm
DB72-00459A
Drain Plug
DB67-20011A
Rubber Leg
DB73-20134A
Cable-Tie
DB65-10088C
Cement Nail
M4x16 Tapping Screws
6002-000215
Drain Hose, length 2m
DB67-00274A
Putty 100g
DB98-10568A

(12)
2-6
Remark
Accessory
Box
Samsung Electronics
5. Exploded Views and Parts List

5-1 Indoor Unit
1-2
14
1-1
15
10
12
16
11
13
4
2-1
2-2
2-3
3-8
3-6
5-1
3-4
5-4
3-1
3-7
5-2
3-2
5-3
3-5
3-3
5-1
Samsung Electronics
Operating
Exploded
Instructions
Views
and
and
Installation
Parts List
Part List
No.
1
Code No.
Description
Specification
AQ12FA
QTY
SA/SNA
AQ12FASER AS12FAXFA AS12FBAXAP
DB94-00454B ASSY BACK BODY
ASSY
SA
1-1
DB61-01632A BODY BACK
HIPS
SNA
1-2
DB69-00834A CUSHION-BODY BACK
EPS
SNA
DB96-06693D ASSY EVAP-TOTAL
ASSY
SA
SA
SNA
DB96-06693E
2-1
DB63-00850A COVER-BEARING
ABS
2-2
DB96-05153C ASSY TUBE EVAP IN
ASSY
SA
SA
SA
SA
DB96-04852A
2-3
DB96-03054K ASSY TUBE EVAP OUT
ASSY
DB96-04851B
3
DB94-00457H ASSY TRAY DRAIN
ASSY
SA
3-1
DB63-00848A TRAY DRAIN
ABS
SA
3-2
DB61-01635A BLADE-H
HIPS
SA
3-3
DB61-01636A BLADE-V
PP
SA
3-4
DB63-00849A TRAY-STABILIZER
ASB
SNA
3-5
DB69-00839A CUSHION EPS-TRAY RH
EPS
SNA
3-6
DB73-00180A RUBBER-CAP DRAIN
GUM-EPM
SNA
3-7
DB95-20138A ASSY MOTOR-STEPPING
GSP-24RW-046
SA
3-8
DB94-00458B ASSY DRAIN-HOSE
ASSY
SA
DB93-04192N ASSY CONTROL IN
ASSY
SA
DB93-04192E
ASSY
SA
DB93-04192P
ASSY
SA
DB93-04192F
ASSY
SA
DB92-00853A ASSY PANEL FRONT
ASSY
SA
5-1
DB64-00989A PANEL FRONT
HIPS
SA
5-2
DB92-00848A ASSY GRILLE-AIR INLET
ASSY, HIPS
SA
5-3
DB97-02064A ASSY COVER-DISPLAY
HIPS,PC
SA
5-4
DB63-01591A GUARD-AIR FILTER
PP
SA
DB97-02851B ASSY-PLATE HANGER
SGCC, T0.6
SA
DB61-01638A HOLDER-PIPE
HIPS
SA
DB63-00844A COVER TERMINAL
HIPS
SA
DB93-03170M ASSY REMOCON
H/P
SA
DB93-03170N
C/O
SA
10
DB96-03149A ASSY EVAP-SUPPORT RH
HIPS
SA
11
DB31-00219A MOTOR FAN
50/60Hz
SA
12
DB94-00456A ASSY CROSS FAN
AS+GF20%
SA
13
DB97-02075A ASSY BOLT-SPECIAL
SA
14
DB94-00455A ASSY BEARING-RUBBER
SA
15
DB94-40007A ASSY BEARING-MOTOR
SA
Samsung Electronics
5-2
PART LIST
SVC LOC
CODE NO
DESCRIPTION
SPECIFICATIONQ
Q'TY
SA/SNA
A0071
DB94-00454J
ASSY BACK BODY
E,Y,GRAY,R22,LF&RH,EXPORT
SA
A0120
DB94-00455A
ASSY BEARING-RUBBER
SS-PJT,CR,BLK SSEC
SA
A0252
DB96-10256A
ASSY U-BEND
C1220T-0,OD7,T0.41,RING 1.3
SA
A0696
DB93-04192N
ASSY CONTROL IN
C/O,-,9K/12K,-,-,-,IN,-,
SA
A0748
DB90-02167B
ASSY COVER-CONTROL IN
WW1-PJT,SSEC
SA
A0755
DB90-03094A
ASSY COVER-DISPLAY
FORTE,SSEC
SA
A0821
DB94-00456A
ASSY-CROSS FAN
SS-PJ,SSEC
SA
A1008
DB96-06862A
ASSY EVAP-TOTAL
FORTE1-INV,SSEC
SA
A1032
DB96-03149B
ASSY EVAP-SUPPORT RH
SS-PJT,-,HIPS,-,-,-
SA
A1203
DB92-00848F
ASSY GRILLE-AIR INLET
FORTE,SSEC
SA
A1579
DB95-20138A
ASSY MOTOR-STEPPING
GSP-24RW-046,AS-568
SA
A1698
DB92-00853F
ASSY PANEL FRONT
NO,-,NO,WHITE,RIGHT,VAL
SA
A1756
DB93-04181A
ASSY PCB MAIN
WW2-P/J,EXP,MAIN ,SSEC
SA
A1756
DB93-04203A
ASSY PCB MAIN
WW1-P/J,EXP,POWER,SSEC
SA
A1839
DB97-02851B
ASSY-PLATE HANGER
KFR-35GW/WAB,CHINA
SA
A1879
DB93-01549F
ASSY-POWER CORD
MID,E,CB
SA
A1928
DB93-03170M
ASSY REMOCON
WW-PJT(Forte), Exp,ARH-462
SA
A2303
DB94-00457J
ASSY TRAY DRAIN
WHITE,RH,1M,Y,R22,-,EXPO
SA
A2355
DB96-03056A
ASSY TUBE EVAP IN
SS-PJT,SSEC 12K
SA
A2356
DB96-03174A
ASSY TUBE EVAP OUT
SS-PJT,SSEC 9K
SA
B0147
DB61-01635C
BLADE-H
FORTE,HIPS,SC-06106R,650.5*56*22
SA
B0179
DB61-01636A
BLADE-V
SS-P/J,PP,BLK,-,SSEC
SA
C0916
DB39-01174A
CONNECT WIRE-PBA
SS-P/J,-,-,1-PIN,-,BRN,
SA
C1485
DB63-00844D
COVER-TERMINAL
FORTE,ABS,2.5,96.4,123,V0
SA
G0120
DB63-01591A
GUARD-AIR FILTER
WW1,PP,2.0,303.4,371.9,
SA
H0286
DB61-01638B
HOLDER-PIPE
VIVACE1,HIPS,2.5,68.5,153.5,
SA
M0039
DB31-00219A
MOTOR FAN
YDK-016S41408-01,SS-P/J Motor
SA
P0021
DB64-00989E
PANEL FRONT
FORTE,HIPS,2.5,285,822,-,WHI
SA
S0224
DB67-60030A
SPRING-SENSOR
WW2-PJT,SGCC,-,-,-,-,-,T0.
SA
T0125
DB62-02813A
TUBE-CU
-,C1220T-O,0.28,7.0,-,-,Tw0.25 H
705.6
SA
5-2 Outdoor Unit(H/P)
20
14-4
14-2
19
18
14
14-1
16
14-3
10
14-5
9
11
3-2
13
12
7
6
3-1
15
4
17
1
2
5
5-3
Samsung Electronics
Exploded Views and Parts List
Part List
No.
Code No.
Description
Specification
AQ12FA
QTY
SA/SNA
AQ12FASER
DB90-01341A ASSY-CABI FRONT
ASSY
SA
DB63-00847A GUARD FAN
PP
SA
DB90-01332A ASSY CABINET-SIDE LF
ASSY
SA
3-1
DB64-01094A CABINET-SIDE LF
SGCC
SA
3-2
DB64-00992A HANDLE-LF
PP
SA
DB90-01546H ASSY CABINET-SIDE RH
ASSY
SA
DB63-00853A COVER-CONTROL
ABS-V0
SA
DB90-01330B ASSY BASE OUT
ASSY
SA
DB99-00401A ASSY VALVE-BRACKET
SGCC
SA
DB94-00668B ASSY PARTITION
ASSY
SA
DB61-01644A BRACKET-MOTOR
SGCC T1.6
SA
10
DB97-02225A ASSY SUPPORT-PLATE B/M
SGCC
SA
11
DB31-00220A MOTOR FAN
YDK020S62213-03
SA
12
DB67-00397A FAN-PROPELLER
AS+GF20%
SA
13
DB60-30020A SCREW-MACHINE
SA
14
DB93-03914F ASSY CONTROL OUT
SA
SA
ASSY
DB93-04248A
14-1
2301-001375
C-FILM
1.5uF/450VAC
SNA
14-2
2501-001237
C-OIL
35uF/450VAC
SNA
2501-001238
40uF/450VAC
SNA
14-3
DB65-40049E TERMINAL-BLOCK
4P
SNA
14-4
DB61-02184A CASE CONTROL OUT
SGCC
SNA
14-5
DB93-00481K ASSY LEAD WIRE-COMP
SNA
15
G4B129JXAEL ROTARY COMPRESSOR
R410A, 50Hz
SA
44D129MXAEL
R22, 50Hz
SA
DB96-05976B ASSY COND
ASSY
SA
DB96-03861G
ASSY
SA
17
DB62-03859A INSULATION-SOUND
EVA+FELT
SA
18
DB96-03858E ASSY TUBE CAPILLARY
ASSY
SA
DB96-03858G
ASSY
SA
DB96-06726A ASSY VALVE 4WAY
ASSY
SA
DB96-07154A
ASSY
SA
DB61-02891A GUIDE-SCREEN
P.E.H. 100%
SA
16
19
20
Samsung Electronics
5-4
5-3 Outdoor Unit(C/O)
11
11-10
11-9
11-1
11-5
11-3
11-4
11-2
8
4
6
10
14
12
16
17
5-1
15
13
5-2
5-5
Samsung Electronics
5-8
Part List
No.
Code No.
Description
Specification
QTY
SA/SNA
AS12FAXFA AS12FBAXAP
DB90-01875A ASSY BASE-OUT PAINT
ASSY
SA
DB94-00927A ASSY-BRACKET VALVE
PP
SA
DB90-01279C ASSY-BRACKET MOTOR
ASSY
SA
DB94-00431D ASSY PARTITION
ASSY
SA
DB90-02372B ASSY CABINET FRONT
ABS-V0
SA
5-1
DB64-01517A CABINET FRONT
PP
SNA
5-2
DB81-00650A BELL MOUSE
PP
SNA
DB64-01518B CABINET-SIDE
PP
SA
DB63-01428A COVER-CONTROL OUT
PP
SA
DB67-00036A FAN-PROPELLER
ASSY
SA
DB31-00034A MOTOR FAN-OUT
ASS025WTVA
SA
10
DB60-30020A SCREW-MACHINE
SGCC
SA
11
DB93-03879B ASSY CONTROL OUT
YDK020S62213-03
SA
2501-001237
35uF/450VAC
SNA
11-1
C-OIL
2501-001236
30uF/450VAC
SNA
11-2
DB93-00481C ASSY LEAD WIRE
ASSY
SNA
11-3
DB61-01102A HOLDER-CAPACITOR
ABS
SNA
11-4
DB65-40049E TERMINAL-BLOCK
4P
SNA
11-5
2301-001375
1.5uF/450VAC
SNA
11-6
DB61-01196A CASE-CONTROL OUT
PP
SNA
44D124DXAEL ROTARY COMPRESSOR
R22, 50Hz
SA
44B135IXAEL
R22, 60Hz
13
DB72-00720A SPONGE-COMP SIDE
14
DB96-05701B ASSY COND
ASSY
DB96-05701A
ASSY
DB96-06390A ASSY TUBE SUCTION
ASSY
DB96-06390B
ASSY
DB96-06389A ASSY TUBE DISCHARGE
ASSY
DB96-06389B
ASSY
DB96-05608E ASSY TUBE CAPILLARY
ASSY
12
15
16
17
Samsung Electronics
C-FILM
SA
1
SA
1
SA
SA
1
1
SA
SA
SA
SA
SA
5-6
5-4 Ass'y Control In

DB93-04479A
A-TYPE
5-9
B-TYPE
Samsung Electronics
Part List
DB93-04479F
No.
Code No.
1
2
3
4
6002-000231
6501-000123
DA02-10017J
DB32-00020E
TH,+,-,2S,M4,L12,ZPC(YEL),SWRCH18A,DACT-140,-,W3.6,L146,NTR,NYLON66
3M #8915,-,T0.15,W18,L55M,-,103AT,-,-,-20~+100,-,-,-,-,SSEC
1
2
1
1
SA
SNA
SNA
SA
SCREW-TAPPING
CABLE TIE
TAPE ETC-FILAMENT
THERMISTOR-WIRE
ASSY
DB39-01165E CONNECT WIRE
Description
Specification
SNA
6
7
8
9
10
DB61-01980A
DB61-02618B
DB62-03861C
DB63-00851A
DB65-00176D
WW2-P/J,#1015 16 AWG,-,1P,-,BLU,-,175022-1
(AMP),175057-1 (AMP),TP,220V/50Hz,4mm,120mm,-,,TUBE?SSEC
AQT24W6WE,ABS,2.0,-,-,BLACK,FORTE,ABS,2.0,156,257,BLACK,SSEC
NEW-WW1,PEB-2,GREEN,15,20,30,SSEC
SS-PJT,ABS,-,-,-,-,-,NO,SSEC
WW1,JXW,4PIN,4mm,36.4*47,BLK,600V,30A
1
1
1
1
1
SA
SA
SNA
SNA
SNA
1
1
1
SNA
SNA
SC
1
1
2
SA
SA
SA
HOLDER-WIRE CLAMP
CASE CONTROL-IN
SEAL-CONTROL IN
COVER-DRAIN
TERMINAL BLOCKTERMINAL
11 DB68-02809A LABEL BAR CODE
-,-,-,-,W170,L115,-,-,-,FOR PACKING CASE
12 DB91-00309A ASSY-SCREW TAPPING WW-INV,M3*20,PH,+,ZPC(YEL)
13 DB93-01638F ASSY POWER CORD
NO PLUG,EXPORT,250V/20A,2340mm,13mm,N,
QTY SA/SNA
MG630591,WHITE,NO,H05VV-F 3*2.5,WW2-PJT,H05VV-F
3*2.5
14 DB93-04181A ASSY PCB MAIN
15 DB93-04203E ASSY PCB MAIN
WW-P/J?H/P?25A,POWER,SSEC
16 DB97-02418A ASSY-SCREW TAPPING SS-P/J,TH,M4*L14
DB93-04479G
No.
Code No.
1
2
3
4
6002-000231
6501-000123
DA02-10017J
DB32-00020E
Description
SCREW-TAPPING
CABLE TIE
TAPE ETC-FILAMENT
THERMISTOR-WIRE
ASSY
Specification
TH,+,-,2S,M4,L12,ZPC(YEL),SWRCH18A,DACT-140,-,W3.6,L146,NTR,NYLON66
3M #8915,-,T0.15,W18,L55M,-,103AT,-,-,-20~+100,-,-,-,-,SSEC
WW2-P/J,#1015 16 AWG,-,1P,-,BLU,-,175022-1
6 DB61-01980A HOLDER-WIRE CLAMP AQT24W6WE,ABS,2.0,-,-,BLACK,7 DB61-02618B CASE CONTROL-IN
FORTE,ABS,2.0,156,257,BLACK,SSEC
8 DB62-03861C SEAL-CONTROL IN
NEW-WW1,PEB-2,GREEN,15,20,30,SSEC
9 DB63-00851A COVER-DRAIN
10 DB65-00061F TERMINAL BLOCK
C/O,2P,N(1),1,2TAB,2SCREW,300V,20A,36.4*24.2,BLACK,N(1),1
11 DB68-02809A LABEL BAR CODE
12 DB91-00309A ASSY-SCREW TAPPING WW-INV,M3*20,PH,+,ZPC(YEL)
13 DB93-01638F ASSY POWER CORD
NO PLUG,EXPORT,250V/
20A,2340mm,13mm,N,MG630591,WHITE,NO,H05VV-F
3*2.5,WW2-PJT,H05VV-F 3*2.5
15 DB93-04203F ASSY PCB MAIN
WW-P/J?C/O?25A,POWER,SSEC
Samsung Electronics
QTY SA/SNA
1
2
1
1
SA
SNA
SNA
SA
SNA
1
1
1
1
1
SA
SA
SNA
SNA
SNA
1
1
1
SNA
SNA
SA
1
1
2
SA
SA
SA
5-10
DB93-04193A
3-26
Samsung Electronics
Part List
DB93-04193C
No.
Code No.
Description
Specification
QTY SA/SNA
6501-000123 CABLE TIE
DACT-140,-,W3.6,L146,NTR,NYLON66
SNA
103AT,-,-,-20~+100,-,-,-,-,SSEC
SA
DB32-00020E THERMISTOR-WIRE
ASSY
SNA
DB61-01980A HOLDER-WIRE CLAMP
WW2-P/J,#1015 16 AWG,-,1P,-,BLU,-,175022-1
AQT24W6WE,ABS,2.0,-,-,BLACK,-
SA
DB61-02893A CASE CONTROL-IN
WW2,ABS(V0),2.0,179,269,BLACK,SSEC
SA
DB63-00851A COVER-DRAIN
SNA
WW1,JXW,4PIN,4mm,36.4*47,BLK,600V,30A
SNA
DB65-00176D TERMINAL BLOCKTERMINAL

DB68-02809A LABEL BAR CODE
SNA
DB91-00309A ASSY-SCREW TAPPING WW-INV,M3*20,PH,+,ZPC(YEL)
SNA
SA
11 DB93-04128E ASSY PCB-POWER
HO5VV-F,-,250V 20A,2,000 ? 20,-,-,-,Gray,,3G*2.5,WW2,SSEC

WW2-P/J?H/P?1-STEP,POWER,SSEC
SA
SA
SA
10 DB93-01638D ASSY POWER CORD
DB93-04193D
No.
Code No.
Description
Specification
QTY SA/SNA
6501-000123 CABLE TIE
DACT-140,-,W3.6,L146,NTR,NYLON66
SNA
103AT,-,-,-20~+100,-,-,-,-,SSEC
SA
DB32-00020E THERMISTOR-WIRE
ASSY
SNA
DB61-01980A HOLDER-WIRE CLAMP
WW2-P/J,#1015 16 AWG,-,1P,-,BLU,-,175022-1
AQT24W6WE,ABS,2.0,-,-,BLACK,-
SA
DB61-02893A CASE CONTROL-IN
WW2,ABS(V0),2.0,179,269,BLACK,SSEC
SA
DB63-00851A COVER-DRAIN
SNA
DB65-00061F TERMINAL BLOCK
SNA
DB68-02809A LABEL BAR CODE
C/O,2P,N(1),1,2TAB,2SCREW,300V,20A,36.4*24.2,BLACK,N(1),1
SNA
DB91-00309A ASSY-SCREW TAPPING WW-INV,M3*20,PH,+,ZPC(YEL)
SNA
HO5VV-F,-,250V 20A,2,000 ? 20,-,-,-,Gray,,3G*2.5,WW2,SSEC

WW2-P/J?C/O?0-STEP,POWER,SSEC
SA
SA
SA
SA
10 DB93-01638D ASSY POWER CORD

11 DB93-04128D ASSY PCB-PAWER
FORTE
Samsung Electronics
3-27
8. Schematic Diagram
8-1. Main PCB
This Document can not be used without Samsung's authorization.
3-40
Samsung Electronics
8-1
8-2. Power PCB
Samsung Electronics
3-41
4. Disassembly and Reassembly

Stop operation of the air conditioner and remove the power cord before repairing the unit.
4-1 Indoor Unit

No
Parts
Front Grille
Procedure
Remark
1) Stop the air conditioner operation and

shut off the main power.
2) Open the Front Grille by pulling right and

left sides of the hook.
3) Loosen 1 of the right screw and detach

the Terminal Cover.
4) Detach the thermistor from the Front
Grille.
5) Loosen 3 fixing screws of Front Grille.
4-1
Samsung Electronics
Disassembly and Reassembly
No
Parts
Procedure
Remark
6) Unlock 3 hooks to fix Panel Front and

Tray Drain.
7) Unlock 3 hooks to fix Panel Front and

Back-Body.
Control-In
(Main PCB)
1) Take all the connector of PCB upper side

out. (Inclusion Power Cord)
2) Detach the outdoor unit connection wire
from the Terminal Block.
3) Loosen 4 fixing screws of Assy Control-In.
Tray Drain
1) Pull Tray Drain out from the Back Body.
Samsung Electronics
4-2
Disassembly and Reassembly
No
Parts
Heat Exchanger
Procedure
Remark
1) Loosen 2 fixing earth screws of right side.

2) Detach the Connection Pipe.
3) Detach the Holder Pipe at the rear side.
4) Loosen the 4 fixing screws of right and left

side.
5) Lifting the Heat Exchanger up a little to
push the up side for separation from the
indoor unit.
4-3
Fan Motor
&
Cross Fan
1) Loosen the fixing screw.

2) Detach the Fan Motor from the Fan.
3) Detach the Fan From the left Holder
Bearing.
Samsung Electronics
4-2 Outdoor Unit

12K H/P
No
Parts
Common Work
Procedure
Remark
1) Loosen the fixing screw of the

Cover Control.
2) Loosen the fixing screws on right and left,

back Cabinet-Side edge and a fixing screw
on the Cabinet-Front lower to detach the
Cabinet-Front.
3) Loosen the fixing screws of the

Assy-Control out.

Cabinet-Side RH.

Cabinet-Side LF.
Samsung Electronics
4-4
Operating Instructions
Disassembly
and Reassembly
and Installation
No
Parts
Fan
&
Motor
Heat Exchanger
Compressor
Procedure
Remark
1) Detach the Nut Flange.(Turn counterclockwise

because the screw is right-handed)
2) Detach the Fan.
3) Loosen 4 fixing screws to detach
the Motor.
1) Loosen 3 fixing screws of the Bar Steel.

2) Loosen 2 fixing screws on both sides.
3) Disassemble the pipe in both inlet and
outlet with welding torch.
4) Detach the Heat Exchanger.
1) Loosen the Terminal Cover nut to open the

Terminal Cover.
2) Disassemble the cloth sound felt.
3) Disassemble the pipe in both inlet and
outlet of the Compressor with welding
torch.
4) Loosen the 3 bolts at the bottom.

5) Detach the Compressor.
4-5
Samsung Electronics
12K C/O
No
Parts
Common Work
Procedure
Remark
1) Loosen 2 fixing screws and separate the

Cover Terminal.

Cover Control.
3) Separate the connection wire from the
Terminal Block.

Cabinet Front.
5) Loosen 1 fixing screw of Assy E-part.

Cabinet-Side
Samsung Electronics
4-6
No
Parts
Fan
&
Motor
Procedure
Remark
1) Remove the Nut Flange.

(Turn to the clockwise)
2) Separate the Fan.
3) Loosen 4 fixing screws to separate the

Motor.
Motor Bracket from the Base.
4-7
Heat Exchanger
1) Loosen 2 fixing screws of left and right side.

2) Disassemble the inlet and outlet pipe by
welding.
3) Separate the Heat Exchanger.
Compressor
1) Open the Terminal Cover of Compressor and

unscrew the Connection Terminal.
2) Disassemble the inlet and outlet pipe of
Compressor by welding.
3) Loosen 3 bolts of the lower part.
4) Separate the Compressor.
Samsung Electronics
MEMO
Samsung Electronics
4-8
12. Troubleshooting
Check the basic items first to judge if the problem was caused by breakdown or misuse. If none of the basic items are related to the
problem, please scrutinize the machine according to the Breakdown Diagnosis by Symptoms method.
12-1 Basic Breakdown Diagnosis Items

1. The input voltage should be rating voltage 10% range.
The airconditioner may not operate properly if the voltage is out of this range.
2. Is the link cable linking the indoor unit and the outdoor unit linked properly?
Check the terminals if the indoor unit and outdoor unit are properly linked by the same number of cables.
Otherwise the airconditioner may not operate properly.
3. When a problem occurs due to the contents illustrated in the table below it is a symptom not related to the malfunction of the
airconditioner.
No
Operation of air conditioner
Explanation
The OPERATION indication LED(GREEN) blinks when a

power plug of the indoor unit is plugged in for the first time.
It indicates power is on. The LED stops blinking if the operation

ON/OFF button on the remote control unit is pushed.
In a COOL operation mode, the compressor does not

operate at a room temperature higher than the setting
temperature that the INDOOR FAN should operate.
In a HEAT operation mode, the compressor does not operate
at a room temperature lower than the setting temperature
that indoor fan should operate.
In happens after a delay of 3 minutes when the compressor

is reoperated. The same phenomenon occurs when a power
is on.
As a phenomenon that the compressor is reoperated after a
delay of 3 minutes, the indoor fan is adjusted automatically
with reference to a temperature of the air blew.
Fan speed setting is not allowed in DRY(
Compressor stops operation intermittently in DRY(
Compressor of the outdoor unit is operating although it is

turned off in a HEAT mode.
When the unit is turned off while de-ice is activated,

the compressor continues operation for up to 9 minutes
(maximum) until the deice is completed.
Timer LED(GREEN) of the indoor unit lights up and the

air conditioner does not operate.
Timer is being activated and the unit is in ready mode.

The unit operates normally if the timer operation is cancelled.
The compressor and indoor fan stop intermittently in

HEAT mode.
The compressor and indoor fan stop intermittently if room

temperature exceeds a setting temperature in order to protect
the compressor from overheated air in a HEAT mode.
Indoor fan and outdoor fan stop operation intermittently

in a HEAT mode.
The compressor operates in a reverse cycle to remove

exterior ice in a HEAT mode, and indoor fan and outdoor fan
do not operate intermittently for within 20% of the total heater
operation
The compressor stops intermittently in a COOL mode or

DRY mode, and fan speed of the indoor unit decreases.
The compressor stops intermittently or the fan speed of the

indoor unit decreases to prevent inside/outside air frozen
depending on the inside/outside air temperature.
Samsung Electronics
The speed of the indoor fan is set to LL in DRY mode.

Fan speed is selected automatically in AUTO mode.
) mode.
) mode.
Compressor operation is controlled automatically in DRY

mode depending on the room temperature and humidity.
12-1
12-2 Trouble check in the initial status

12-2-1 Diagnosis and marking of the part in trouble.
Please check the air conditioner operation status and write the check result in the chart in the room.
LAMP
OPERATION
Description
TIMER
TURBO
Indoor unit room temperature sensor error

(open or short)
Indoor unit heat exchanger temperature sensor error
(open or short)
Indoor fan motor mal function
EEPROM error
Option error
(option wasnt set up or option data error)
: Lamp off
: Lamp flickering
12-2-2 Operation with abnormal motion

No
1
12-2
Abnormal condition
No response from
the remote control
operation signal.
Inspection
Initial Diagnosis
Plug out and plug in 5 seconds later. Able to operate the OK

remote control.
Unable to operate the Press the TURBO button with the

outdoor unit
remote control.
In 3 minutes, check the voltage
between the indoor unit terminal
block N1 and 1.
Unable to operate Press the button in the indoor unit.

the remote control. If it operates, the remote control and
indoor unit receiver are in trouble.
If not, the indoor unit is in trouble.
AC200V ~ AC240V Problem with the outdoor unit or PCB
No power source
displayed.
Problem with the relay (RY71) or PCB
Samsung Electronics
Troubleshooting
12-3 Breakdown diagnosis by symptoms

12-3-1 No Power (completely dead)-Initial diagnosis
1. Checklist :
1) Is input voltage normal?
2) Is AC power linked correctly?
3) Is input voltage of DC regulator IC KA7812 (IC01) normal? (11.8VDC-12.2VDC)
4) Is output voltage of DC regulator IC KA7805 (IC02) normal? (4.5VDC-5.5VDC)
2. Troubleshooting procedure
Unplug the power cord and plug it after 5 seconds
Press the Power Button on

the remote control unit to operate the air
conditioner
operate
Check the display board
does not operate
Check the indoor unit control board
Check whether two wires

of power cord are connected correctly to the
terminal block and control board.
No
Reconnect wires correctly
Yes
Check whether the fuse

on the control board is normal.
F701: 3.15(2.5)[A]/250[V]
No
Replace fuse
Yes
Check the output of

SMPS on the control board.
Input power: AC23015%[V]
IC02 Input: DC12[V]
IC02 output: DC5[V]
No
Replace the control board
Yes
Check the setting temperature
Samsung Electronics
12-3
Troubleshooting
12-3-2 When the Indoor Unit Fan Does Not Operate. (Initial Diagnosis)
1. Checklist :
1) Is the indoor unit fan motor properly connected with the connector (CN72)?
2) Is the AC voltage correct?
3) Is HALL IC in indoor fan motor properly connected with the connector (CN44)?
4) Is the running capacitor (CR71) properly connected with PCB board?
After unplugging out the power cord should

be reconnected within 5 seconds.
Yes
No
Does the OPERATION lamp blink?
Check as in the procedure

"No power parts"
Yes
Does the Solid State Relay(SS71) work properly?

Test rod location
+
SS71-
SS71-
No
Micom is
out of order.
Micom
should be replaced
No
PCB is
out of order.
PCB should be
replaced.
Normal
Voltage
12V
Yes
Is the supply voltage of the fan motor sufficient?

Test rod location
PCB CN72
Condition
pin #3 and #5
Fan operate
Normal
Voltage
About AC
180V
Motor Fan-Capacitor is out of order
Yes
Fan motor
is out of order.
12-4
Replace Motor
Fan-Capacitor
Fan motor
should be replaced.
Samsung Electronics
Troubleshooting
12-3-3 When the Outdoor Unit Does Not Operate. (Initial Diagnosis)
1. Checklist :
2) Is the set temperature of the remote control higher than room temperature in COOL mode?
3) Is the set temperature of the remote control lower than room temperature in HEAT mode?
4) Is the POWER IN wire_power(N) linked correctly?
5) Is the outdoor unit properly connected with the TERMINAL BLOCK connector(N1, L1, 1, 2, 3, 4 or N1,1, 2, 3)?
After unplugging out the power cord should be
reconnected within 5 seconds.
No
Does the OPERATION lamp blink

"No Power parts"
Yes
Room temperature sensor is

out of order
Yes
Does the timer lamp blink during operation?
No
@
#
No
Is the power relay RY71 operated by adjusting

the room temperature?
Test rod location
+
Condition
IC04 Pin No.38
GND
RY71 ON
PCB should be checked.
Micom is
out of order.
Normal
Voltage
PCB should be checked.
DC4.8V
Yes
Is rating voltage 10% range applied relay between

Terminal block No. N1 and No. 1
No
Power relay is
out of order
Power relay should be

replaced.
Yes
Outdoor unit is out of order.

No
!
Yes
Is the room sensor normal register?

10C
20C
30C
17.96k
12.09k
8.3k
Samsung Electronics
12-5
Troubleshooting
12-3-4 When the UP/DOWN Louver Motor Does Not Operate. (Initial Diagnosis)
1. Checklist :
2) Is the UP/DOWN louver motor properly connected with the connector (CN61)?
Remove power cord and plug in again approx.

5 seconds.
No

"No Power parts".
Yes
Does operation start when

swing button of the remote control unit
pushed?
Yes
Normal
No
Voltage at pin #57~#60

of micom (IC04) change?
(Squarewave)
No
Micom (IC04) is faulty.
Yes
Voltage at pin #14 ~ #16 of

IC06(ULN2003A) and pin 14#
of IC05 change?(Squarewave)
No
Driver IC05/06 (ULN2003A) is faulty.
Yes
UP/DOWN louver motor is faulty.
12-6
Samsung Electronics
Troubleshooting
12-3-5 In the HEAT mode, When there is no warm air current. Check this first;
1) Is the set temperature of Remote Control lower than room temperature in Heat mode?
2) Is the Indoor PCB properly connected with WIRE[power(N),fan(H),4-way,fan(L)]?
After training on, the heating operation

should start in 5 minutes.
No
Is the number #38 of Micom (IC04)

DC5.0V?
No
Abnormal Micom
Yes
Is the number checking

#13 of IC05 (ULN2003A) LOW?
No
Abnormal Micom
Yes
Is the voltage between

CN71 #1 and CN71 #5 rating voltage
10% range
No
Abnormal IC05
Yes
Abnormal 4-Way valve of Outdoor Unit.

or connecting Cable
4-Way valve should be replaced

or connecting Cable Check.
Samsung Electronics
No
Abnormal RY73
PCB should be replaced.
12-7
Troubleshooting
12-3-6 Room temperature sensor failure

LAMP
OPERATION
Description
TIMER
TURBO
Indoor unit room temperature sensor error(open or short)

: Lamp off
: Lamp flickering
Detach the assembly sensor from the

ASS'Y PCB CN43 connector and measure
the sensor resistance with an ohmmeter (tester).
Is the sensor resistance value

10K 3% at the room temperature
of 25C?
No
ASS'Y Sensor Replace

SENSOR Resistance Value : 20C-12.09k
Yes
Connect the sensor to CN43,

supply power, and measure the voltage of
#1 and #2 of the CN43 connector.
Yes
Poor ASS'Y PCB Replace
Below 0.5V?
No
Yes
Over 4.9V?
No
MICOM Error or Connector(CN43) check
12-8
Samsung Electronics
Troubleshooting
12-3-7 Room Pipe sensor failure

LAMP
OPERATION
Description
TIMER
TURBO

(open or short)
: Lamp off
: Lamp flickering
1. Check the assembly condition of the sensor connector(CN43) on the indoor unit Main PCB and if not assembled, reassemble the
connector accurately.
2. Detach the room pipe sensor connector(CN43) and check the resistance between connector 3 and 4.
Temperature(C)
Resistance Value(Kohm)
Temperature(C)
15
14.68
30
8.31
20
12.09
35
6.94
25
10
40
5.83
Others
The data tolerance
is 3%.
If the above data is not met, replace the room pipe sensor.
3. Assemble the room pipe sensor to PCB, plug in, and check the voltage of connector 3 and 4. If the resistance is below 0.5V or
over 4.9V, replace the indoor Main PCB. (short or disconnected in the PCB board)
12-3-8 When the remote control is not receiving.

1. Check if the connector was normally assembled.
2. Put the set in operation and check the voltage of Vout(+) and Gnd(-) of the RM01 while operating the
remote control. When the voltage descends below 3V, the assembly module PCB is normal and the main PCB is poor.
Then replace the main PCB.
Samsung Electronics
12-9
12-4 PCB Inspection Method

12-4-1 Pre-inspection Notices
1. Check if you pulled out the AC power plug when you eliminate the PCB or front panel.
2. Don't hold the PCB side not impose excessive force on it to eliminate the PCB.
3. Don't pull the lead wire but hold the whole housing to connect or disconnect a connector to the PCB.
12-4-2 Inspection Procedure

1. Check connector connection and peeling of PCB or bronze coating pattern when you think the PCB is broken.
2. The PCB is composed of the 2 parts.
POWER PCB Part : relay, room fan motor driving circuit and control circuit,
power circuit of DC12V and DC5V, and buzzer driving circuit.
Main PCB Part: MICOM and surrounding circuit,LED lamp,sensor driving circuit,Switch
12-4-3 Detailed Inspection Procedure

No
Procedure
Plug out and pull the PCB

out of the electronic box.
Check the PCB fuse.
1) Is the fuse disconnected? (F701)
Supply power.
If the operating lamp
twinkles at this time,
the above 1)~3) have
no relation.
Checking the power voltage.
Press the ON/OFF button

and operate TURBO
mode.
But, exclude the
RESERVE operation.
Inspection Method
Overcurrent
Indoor Fan Motor Short
AC Part Pattern Short of the MAIN PCB
1) Is the wire_power(N) and comp_RY71 input voltage

AC200V~AC240V?
Power Cord is fault, Fuse open. Wrong

Power Cable Wiring, AC Part is faulty.
2) Is the voltage between both terminals of the

C103 on the 2nd side of the transformer AC12V
0.5V?
Switching Trans or Power Circuit is faulty
3) Is the voltage between both terminals of OUT

and GND of IC02(KA78L05) DC5V 0.5V?
Power Circuit is faulty, Load Short
Checking the power voltage.

1) Check the voltage of the relay(RY71) coil(IC05 PIN
#13 and GND : 0V, PIN#4 and GND : 5V) during
operation(3 minutes after TURBO operation).
Relay(RY71) Coil Disconnection, IC05 is

faulty
2) Check the voltage of both terminals of

terminal block 1 and N1 after 3 minute
operation.: AC220V
Relay(RY71) Contact is faulty
Press the ON/OFF button. 1) Is the voltage over AC180V being imposed
on terminal #3 and #5 of the fan motor
1. FAN Speed [High]
connector(CN72)?
2. Continuous Operation
12-10
Cause
Fan Motor of the indoor is faulty
2) The fan motor of the indoor unit doesn't run.
Fan Motor Connector(CN72) is faulty
3) The power voltage between terminal #3 and #5

of the connector(CN72) is 0V.
ASS'Y POWER OR MAIN PCB is faulty

Connection is faulty
Samsung Electronics
Troubleshooting
12-4-4 Temperature Sensor Feature Conversion Table(Room Temperature Sensor); 103AT

Temperature Sensor Resistance Temperature Sensor Resistance Temperature Sensor Resistance Temperature Sensor Resistance
[C]
[C]
[C]
[C]
[Kohm]
[Kohm]
[Kohm]
[Kohm]
70
69
68
67
66
65
64
63
62
61
60
2.229
2.296
2.365
2.437
2.512
2.589
2.669
2.752
2.838
2.928
3.021
49
48
47
46
45
44
43
42
41
40
4.300
4.444
4.594
4.749
4.912
5.080
5.256
5.439
5.630
5.828
29
28
27
26
25
24
23
22
21
20
8.622
8.944
9.281
9.632
10
10.380
10.780
11.200
11.630
12.090
9
8
7
6
5
4
3
2
1
0
18.700
19.480
20.290
21.150
22.050
22.990
23.900
25.030
26.130
27.280
59
58
57
56
55
54
53
52
51
50
3.116
3.216
3.319
3.426
3.537
3.652
3.772
3.897
4.026
4.161
39
38
37
36
35
34
33
32
31
30
6.033
6.246
6.468
6.699
6.941
7.192
7.455
7.729
8.015
8.313
19
18
17
16
15
14
13
12
11
10
12.560
13.060
13.570
14.120
14.680
15.280
15.900
16.550
17.240
17.960
-1
-2
-3
-4
-5
-6
-7
-8
-9
28.470
29.720
31.040
32.430
33.890
35.430
37.050
38.760
40.560
Temperature Sensor Characteristic Curve

Temperature
( C)
70
60
50
40
30
At the temperature of 25 C(10K)
20
10
0
-10
-9
5
10
15
20
25
30
35
40
Resistance Value (Kohm)
Samsung Electronics
12-11
12-5 Main Part Inspection Method

Part
Room Temperature Sensor
Room Fan Motor
Breakdown Inspection Method

Measure resistance with a tester
Normal
At the normal temperature 37k~8.3k(-7C~+30C) *Refer to Table 12-3-4.
Abnormal
, 0. . . Open or Short
Measure the resistance between terminals of the connector (CN72) with a tester.
Abnormal
Outdoor Fan Motor
Measure the resistance between motor wires with a tester.

Abnormal
Stepping Motor
12-12
Measure the resistance between the red wire and each terminal wire with a tester.
Normal
About 300 at the normal temperature (20C ~ 30C)
Abnormal
Samsung Electronics
MEMO
Samsung Electronics
12-13
3. Alignment and Adjustments

3-1 Test Mode
How to Approach Test Mode
You can approach the Test Mode by pressing the on/off switch of
indoor unit for 5 seconds.
on/off switch
Test Mode Operation Option

After installing the air conditioner, check whether each subordinate is normally operated or not by operating the Test Mode.
Temperature Display Part : Display the set option at one-second intervals. (Only for models having the temperature display part)
ex) 0b0000-1730F8 : 0b00001730F80b ...(Repeat)
When an error occurs, display the Error Mode.
LED Display
LAMP
Waiting Operation
OPERATION
TIMER
TURBO
Cause
Indoor temperature
sensor error
(OPEN /SHORT)
Follow-up Measures
Check assembling status of the sensor parts

connector on the indoor unit main PCB
Measure the resistance value on both sides
connector no. 1 and no. 2 (E1), no. 3 and no. 4
(E2) by separating the sensor parts connector
Temp. Resistance Temp. Resistance
(C) Value(K) (C) Value(K)
Indoor heat exchanger

temperature sensor error
(OPEN /SHORT)
15
14.68
30
8.31
20
12.09
35
6.94
25
10.00
40
5.83
Others
The error of
DATA is
2%.
* If not meet the above DATA, replace sensors.
Indoor fan motor speed

detecting error
(Occur when it continues
for 15 seconds at below
450rpm)
Check assembling status of the Motor Hall IC

output connector (CN44) on the indoor unit
main PCB
EEPROM error
(Option memory)
* Display only for models
having the returning
function for the power failure
Blink all lamps
Samsung Electronics
When there is an option

related error
When options are not set
When there is an option
data error
Reset options
Replace the PCB
Reset options
3-1
Alignment and Adjustments
Test Mode Operation Option(cont.)

Operation Mode : Cool mode. Operate the cool mode by operating the compressor by force without the compressor ON/OFF
according to the set temperature/indoor temperature. (Do not follow the antifreeze control)
Up-down louver : Up-down swing mode
Indoor Fan : High
Because the Test Mode operate the cool mode by force not related to the set temperature / indoor temperature, check
whether each subordinate is operated normally or not after completing installation and must turn off the power of the
air conditioner.
3-2
Samsung Electronics
3-2 Error Mode and Check Method

LAMP
Description
OPERATION
TIMER
TURBO

(open or short)
(open or short)
EEPROM error
Option error
(option wasnt set up or option data error)
: Lamp off
Samsung Electronics
: Lamp flickering
3-3
3-2-1 Room temperature sensor Error

LAMP
Description
OPERATION
TIMER
TURBO

(open or short)
Detach the assembly sensor from the

ASS'Y main PCB CN43 connector and measure
the sensor resistance with an ohmmeter (tester)
between Pin #1 and #2.
Is the sensor resistance value

10K3% at the room temperature
of 25C?
No
ASS'Y Sensor Replace

30C-8.31k
35C-6.94k
40C-5.83k
Yes
Connect the sensor to CN43,
supply power, and measure the voltage of
#1 and #2 of the CN43 connector.
Below 0.5V?
Yes
No
Over 4.9V?
Yes
No
MICOM Error or Connector(CN43) check
3-4
Samsung Electronics
3-2-2 Room Pipe sensor Error

LAMP
OPERATION
Description
TIMER
TURBO

(open or short)
1. Check the assembly condition of the sensor connector(CN43) on the indoor unit Main PCB and if not assembled, reassemble
the connector accurately.
2. Detach the room pipe sensor connector(CN43) and check the resistance between Pin #3 and #4.
Temperature(C)
Temperature(C)
15
14.68
30
8.31
20
12.09
35
6.94
25
10
40
5.83
Others
The data tolerance
is 3%.
If the above data is not met, replace the room pipe sensor.
3. Assemble the room pipe sensor to PCB, plug in, and check the voltage of connector 3 and 4. If the resistance is below 0.5V or
over 4.9V, replace the indoor Main PCB. (short or disconnected in the PCB board)
Samsung Electronics
3-5
3-2-3 Indoor Unit Fan Motor Error

LAMP
OPERATION
Description
TIMER
TURBO
1. Checklist :
1) Is the indoor unit fan motor properly connected with the connector (CN72)?
2) Is the AC voltage correct?
3) Is HALL IC in indoor fan motor properly connected with the connector (CN44)?
4) Is the running capacitor (CR71) properly connected with PCB board?
After unplugging out the power cord should
be reconnected within 5 seconds.
Yes
No
Check as in the procedure "No Power".
Yes
Does the Solid State Relay(SS71) work properly?
Test rod location
+
SS71-
SS71-
No
Micom is
out of order.
Micom should be replaced
No
PCB is
out of order.
PCB should be replaced.
Normal
Voltage
12V
Yes
Is the power relay RY71 operated by

adjusting the room temperature?
Test rod location
PCB CN72
Condition
Normal
Voltage
pin #3 and #5
Fan operating
About AC180V
Motor Fan-Capacitor is out of order
Yes
Fan motor is out of order.
3-6
Replace Motor
Fan-Capacitor
Fan motor should be replaced.
Samsung Electronics
3-3 Setting Option Setup Method
Option No. :
Step 1 : Enter the Option Setup mode.
1st
Take out the batteries of remote control.
2nd
Press the temp.
button simultaneously and
insert the battery again.

3rd
Make sure the remote control display shown as
Step 2 : Enter the Option Setup mode and select your option according to the following procedure.
1
The default value is
Otherwise, push the
.
button to
Every time you push the button, the display panel reads
repeatedly.
1
Push the
button to set the display panel to
...
repeatedly.
5
6
...
repeatedly.
Push the
or
Push the
...
repeatedly.
Push the
...
repeatedly.
Setting is not required if you must
a value which has a default.
Push the
...
repeatedly.
7
8
Samsung Electronics
10
3-7
7
Press
Push the
button, then the default value is
...
repeatedly.
7
8
9
Push the
...
repeatedly.
10
11
10
12
Push the
...
repeatedly.
11
Push the
...
repeatedly.
12
Setting is not required if you must

a value which has a default.
Push the
...
repeatedly.
Step 3 : Upon completion of the selection, check you made right selections.
to set the display part to and check the display part.
Press the Mode Selection key,
The display part shows
Press the Mode Selection key,

The display part shows
to set the display part to
and check the display part.
Step 4 : Pressing the ON/OFF button ( )

When pressing the operation ON/OFF key with the direction of remote control for unit, the sound ''Ding'' or ''Diriring'' is
heard and the OPERATION ICON( ) lamp of the display is flickering at the same time, then the input of option is completed. (If the diriring sound isn't heard, try again pressing the ON/OFF button.)
Step 5 : Unit operation test-run

First, Remove the battery from the remote control.
Second, Re-insert the battery into the remote control.
Third, Press ON/OFF button(
) with the direction of remote control for set.
Error Mode
1stIf all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry.
2nd If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option
code is set up for its model.
3-8
Samsung Electronics
OPTION ITEMS
REMOCON
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
AQ12FA
AQ12FASER
AS12FAXFA
AS12FBAXAP
MODEL
Samsung Electronics
3-9
13. Block Diagram

*: OPTION
CONTROLLER
IC-MCU
HEAT EXCHANGER SENSOR
ROOM TEMPERATURE SENSOR
INFRARED SIGNAL
RESET
CIRCUIT
BLADE CONTROL
INDOOR FAN MOTOR CONTROL
COMPRESSOR CONTROL
OUTDOOR FAN MOTOR CONTROL
4 WAY VALVE CONTROL (*)
TEMPERATURE CONTROL
TIMER
BUZZER CONTROL
DISPLAY PART
OPERATION
TURBO
TIMER
OSCILLATION
CIRCUIT
ZERO
VOLTAGE
DETECT
REMOTE CONTROL
POWER ON/OFF
MODE
(AUTO, COOL, DRY,
FAN),HEAT*
COMPRESSOR CONTROL SIGNAL

OUTDOOR FAN MOTOR CONTROL
SIGNAL
4 WAY VALVE CONTROL SIGNAL*
STEPPING MOTOR CONTROL
SIGNAL
BUZZER CONTROL SIGNAL
TRIGGER
SIGNAL
INDOOR FAN MOTOR
SSR
TURBO OPERATION
FAN SPEED SELECT

(H/M/L/AUTO)
COMPRESSOR DRIVE
OUTDOOR FAN MOTOR DRIVE
4 WAY VALVE DRIVE*
STEPPING MOTOR DRIVE
BUZZER DRIVE
COMPRESSOR
OUTDOOR FAN MOTOR
4 WAY VALVE*
BUZZER
STEPPING MOTOR
: BLADE UP/DOWN
FLAP
DC5V
ON, OFF TIMER
SELECT
TEMPERATURE
SELECT(UP/DOWN)
VOLTAGE REGULATOR
DC12V
SMPS POWER BLOCK
GOOD MORNING
OPERATION
AC INPUT
13-1
Samsung Electronics
Block Diagram
DISPLAY PART
REMOTECONTROL PART
INDOOR FAN CONTROL PART
AC/DC PART
CONNECT
C/W MAIN
PBA
ZERO CROSSING PART

Samsung Electronics
BUZZER CONTROL PART

13-2
10. PCB Diagram

The red number connecter is not used.
8
10
11
14
12
13
Power
Temperature Sensor
Motor RPM Feedback
BLADE-H Motor
Remocon Module
10
HVPS(High voltage Generator)
Humidity Sensor
11
DISPLAY PCB Connection
Anios
12
Melody PCB Connection
Auto grill 1
13
Test Board Connection
Auto grill 2
14
Indoor Fan Motor
Samsung Electronics
10-1
7. Wiring Diagram
H/P
7-1
Samsung Electronics
C/O
Samsung Electronics
7-2
6. Electrical Parts List

MAIN PCB : DB93-04128A
Location No.
Code No.
Description
D101
D102
D103
D104
D105
Q601
Q101
0402-000137
0402-000137
0402-000137
0402-000137
0402-000137
0501-000303
0501-000398
Q102
0501-000398 TR-SMALL SIGNAL
Q602
Q603
ICO1
1203-000243 IC-POSI.FIXED REG.
ICO2
VA71
R103
R104
R105
R605
R606
R609
R610
R102
R608
R602
R603
R601
R101
R607
C107
C108
C102
C104
C106
CR71
1203-000429
1405-000154
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000591
2001-000734
2001-000780
2001-000780
2001-000855
2007-000290
2007-000290
2202-000128
2202-000128
2202-000780
2202-000780
2202-000780
2301-001363
IC-POSI.FIXED REG.
VARISTOR
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CHIP
R-CHIP
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-FILM,LEAD-PPF
XC71
C101
C103
C601
C105
BZ61
RY72
2301-001439
2401-000173
2401-000711
2401-002300
2401-003036
3002-001129
3501-001154
C-FILM,LEAD-PPF
C-AL
C-AL
C-AL
C-AL
BUZZER-PIEZO
RELAY-MINIATURE
RY73
3501-001154 RELAY-MINIATURE
RY74
RY71
SS71
F701
F702
CN72
3501-001268
3502-000115
3601-000263
3601-001209
3711-000262
6-1
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
TR-SMALL SIGNAL
TR-SMALL SIGNAL
RELAY-POWER
SSR
FUSE-CARTRIDGE
FUSE-RADIAL LEAD
HEADER-BOARD TO
CABLE
Specification
QTY
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
KSA733,PNP,250mW,TO-92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
7812,TO-220,3P,-,PLASTIC,11.5/
12.5V,16W,0TO+125C,1A,-,ST,78L05A,TO-92,3P,-,PLASTIC,4.6/
460Vdc,2500A,17.5x7.5mm,TP
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/4W,AA,TP,2.4X6.4MM
100ohm,5%,1/8W,TP,2012
100ohm,5%,1/8W,TP,2012
10nF,+80-20%,50V,Y5V,TP,2.5x4.
10nF,+80-20%,50V,Y5V,TP,2.5x4.
100nF,+80-20%,50V,Y5V,-,3.5x19mm,100nF,+80-20%,50V,Y5V,-,3.5x19mm,100nF,+80-20%,50V,Y5V,-,3.5x19mm,2000nF,+105%,450V,BK,38x18x30mm,33
220nF,10%,275V,BK,18x10x15.8mm,15
1000uF,20%,35V,GP,TP,13x25,5
2200uF,20%,25V,GP,TP,16x25,7.5
47?F,20%,50V,GP,TP,6.3x11,5mm
100uF,20%,16V,GP,TP,5X11mm,5mm
85DB,-,-,2KHZ,12Vdc,200mW,3000mA,1FormA,10mS,
10mS
12Vdc,200mW,3000mA,1FormA,10mS,
10mS
10mS
12V,0.9W,25000mA,SPST,20mS,10mS
12Vdc,-,2A,1mS,1mS
250V,3.15A,TIME-LAG,GLASS,5x20mm
250V,1A,TIME-LAG,-,8.5x8mm
1WALL,3P,1R,7.92MM,STRAIGHT,SN,
WHT
1
1
1
1
1
1
1
SA/SNA Remark
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SA
SA
SA
1
1
1
1
1
SA
SNA
SNA
SNA
SNA
Samsung Electronics
MAIN PCB : DB93-04128A(cont.)

Location No.
CN73
Code No.
Description
J1
3711-003845 HEADER-BOARD TO
CABLE
3812-001283 WIRE-NO SHEATH CU
J2
J3
J4
J5
J6
J7
J8
TR-1
TR-2
TR-3
TR-4
4-WAY
FAN(H)
FAN(L)
POWER(N)
RY-1
RY-2
RY-3
RY-4
ST11
6042-000105
6042-000105
6042-000105
6042-000105
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
DB26-00066A
POWER(N)
FAN(H)
DB39-01270F CONNECT WIRE
4-WAY
DB39-01270G CONNECT WIRE
FAN(L)
DB39-01270H CONNECT WIRE
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
TRANS POWER
DB41-00495A PCB-POWER
F701
DB61-00924A HOLDER-FUSE
DB62-03085A HEAT SINK
Samsung Electronics
Specification
QTY
SA/SNA Remark
BOX,11P,1R,2mm,STRAIGHT,SN,WHT
SNA
TCWA,300V,52mm(TAPING),1/
0.6mm,-,TCWA,300V,52mm(TAPING),1/
0.6mm,-,ID1.6,OD2.0,L6,NI PLT,C2600BD
ID1.6,OD2.0,L6,NI PLT,C2600BD
ID1.8,OD2.2,L3,-,BRASS
-,WW2-VE,-,8-PIN,230V/AC,16.5V/
DC,400mA,-,50hz,-,-,-,-,-,SSEC
WW2-P/J,#1015 18 AWG,-,1P,,BLU,-,175022-1 (AMP),ST780400
(KET),TP,220V/50Hz,4mm,170mm,-,,TUBE?SSEC
WW2-P/J,#1015 18 AWG,-,1P,,RED,-,175022-1 (AMP),ST780400
WW2-P/J,#1015 18 AWG,-,1P,,BLK,-,175022-1 (AMP),ST780400
WW2-P/J,FR-1,ONELAYER,VERSION1,T1.6,-,-,-,-,SSEC
-,FH-51B,-,-,-,-,SSEC
-,A6063,25,15,15,-,-,SSEC
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
SNA
SNA
6-2
Electrical Parts List
MAIN PCB : DB93-04128B

Location No.
Code No.
Description
D101
D102
D103
D104
D105
Q601
Q101
0402-000137
0402-000137
0402-000137
0402-000137
0402-000137
0501-000303
0501-000398
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
TR-SMALL SIGNAL
TR-SMALL SIGNAL
Q102
0501-000398
TR-SMALL SIGNAL
Q602
0501-000398
TR-SMALL SIGNAL
Q603
0501-000398
TR-SMALL SIGNAL
ICO1
1203-000243
IC-POSI.FIXED REG.
ICO2
VA71
R103
R104
R105
R605
R606
R609
R610
R102
R608
R602
R603
R601
R101
R607
C107
C108
C102
C104
C106
CR71
1203-000429
1405-000154
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000591
2001-000734
2001-000780
2001-000780
2001-000855
2007-000290
2007-000290
2202-000128
2202-000128
2202-000780
2202-000780
2202-000780
2301-001363
IC-POSI.FIXED REG.
VARISTOR
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CHIP
R-CHIP
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-FILM,LEAD-PPF
XC71
C101
C103
C601
C105
BZ61
RY72
2301-001439
2401-000173
2401-000711
2401-002300
2401-003036
3002-001129
3501-001154
C-FILM,LEAD-PPF
C-AL
C-AL
C-AL
C-AL
BUZZER-PIEZO
RELAY-MINIATURE
RY74
3501-001154
RELAY-MINIATURE
RY71
SS71
F701
F702
CN72
3501-001268
3502-000115
3601-000263
3601-001209
3711-000262
CN73
3711-003845
RELAY-POWER
SSR
FUSE-CARTRIDGE
FUSE-RADIAL LEAD
HEADER-BOARD TO
CABLE
HEADER-BOARD TO
CABLE
6-3
Specification
QTY
SA/SNA Remark
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
KSA733,PNP,250mW,TO-92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
7812,TO-220,3P,-,PLASTIC,11.5/
460Vdc,2500A,17.5x7.5mm,TP
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/4W,AA,TP,2.4X6.4MM
100ohm,5%,1/8W,TP,2012
100ohm,5%,1/8W,TP,2012
10nF,+80-20%,50V,Y5V,TP,2.5x4.
10nF,+80-20%,50V,Y5V,TP,2.5x4.
220nF,10%,275V,BK,18x10x15.8mm,15
1000uF,20%,35V,GP,TP,13x25,5
2200uF,20%,25V,GP,TP,16x25,7.5
47?F,20%,50V,GP,TP,6.3x11,5mm
10mS
10mS
12V,0.9W,25000mA,SPST,20mS,10mS
12Vdc,-,2A,1mS,1mS
WHT
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SA
SA
1
1
1
1
1
SA
SNA
SNA
SNA
SNA
SNA
Samsung Electronics
MAIN PCB : DB93-04128B(cont.)

Location No.
Code No.
Description
J1
3812-001283
WIRE-NO SHEATH CU
J2
3812-001283
WIRE-NO SHEATH CU
J3
3812-001283
WIRE-NO SHEATH CU
J4
3812-001283
WIRE-NO SHEATH CU
J5
3812-001283
WIRE-NO SHEATH CU
J6
3812-001283
WIRE-NO SHEATH CU
J7
3812-001283
WIRE-NO SHEATH CU
J8
3812-001283
WIRE-NO SHEATH CU
TR-1
TR-2
TR-3
TR-4
FAN(H)
FAN(L)
POWER(N)
RY-1
RY-2
RY-3
RY-4
ST11
6042-000105
6042-000105
6042-000105
6042-000105
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
DB26-00066A
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
TRANS POWER
POWER(N)
DB39-01270E
CONNECT WIRE
FAN(H)
DB39-01270F
CONNECT WIRE
FAN(L)
DB39-01270H
CONNECT WIRE
DB41-00495A
PCB-POWER
DB61-00924A
DB62-03085A
HOLDER-FUSE
HEAT SINK
F701
Samsung Electronics
Specification
-,WW2-VE,-,8-PIN,230V/AC,16.5V/
DC,400mA,-,50hz,-,-,-,-,-,SSEC
WW2-P/J,#1015 18 AWG,-,1P,,RED,-,175022-1 (AMP),ST780400
-,FH-51B,-,-,-,-,SSEC
-,A6063,25,15,15,-,-,SSEC
QTY
SA/SNA Remark
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
SNA
SNA
6-4
MAIN PCB : DB93-04128D

Location No.
Code No.
Description
D101
D102
D103
D104
D105
Q601
Q101
0402-000137
0402-000137
0402-000137
0402-000137
0402-000137
0501-000303
0501-000398
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
TR-SMALL SIGNAL
TR-SMALL SIGNAL
Q102
Q602
Q603
ICO1
ICO2
VA71
R103
R104
R105
R605
R606
R609
R610
R102
R608
R602
R603
R601
R101
R607
C107
C108
C102
C104
C106
CR71
1203-000429
1405-000154
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000591
2001-000734
2001-000780
2001-000780
2001-000855
2007-000290
2007-000290
2202-000128
2202-000128
2202-000780
2202-000780
2202-000780
2301-001363
XC71
C101
C103
C601
C105
BZ61
RY71
F701
F702
CN72
2301-001439
2401-000173
2401-000711
2401-002300
2401-003036
3002-001129
3501-001268
3601-000263
3601-001209
3711-000262
IC-POSI.FIXED REG.
VARISTOR
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CHIP
R-CHIP
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-FILM,LEAD-PPF
J1
C-FILM,LEAD-PPF
C-AL
C-AL
C-AL
C-AL
BUZZER-PIEZO
RELAY-POWER
FUSE-CARTRIDGE
FUSE-RADIAL LEAD
HEADER-BOARD TO
CABLE
CABLE
J2
J3
J4
CN73
3-32
Specification
QTY
SA/SNA Remark
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
KSA733,PNP,250mW,TO-92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
7812,TO-220,3P,-,PLASTIC,11.5/
460Vdc,2500A,17.5x7.5mm,TP
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/4W,AA,TP,2.4X6.4MM
100ohm,5%,1/8W,TP,2012
100ohm,5%,1/8W,TP,2012
10nF,+80-20%,50V,Y5V,TP,2.5x4.
10nF,+80-20%,50V,Y5V,TP,2.5x4.
220nF,10%,275V,BK,18x10x15.8mm,15
1000uF,20%,35V,GP,TP,13x25,5
2200uF,20%,25V,GP,TP,16x25,7.5
47?F,20%,50V,GP,TP,6.3x11,5mm
85DB,-,-,2KHZ,12V,0.9W,25000mA,SPST,20mS,10mS
WHT
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SA
SNA
SNA
SNA
SNA
0.6mm,-,-
SNA
SNA
SNA
SNA
Samsung Electronics
MAIN PCB : DB93-04128D(cont.)

Location No.
Code No.
Description
J5
J6
J7
J8
TR-1
TR-2
TR-3
TR-4
4-WAY
FAN(H)
FAN(L)
POWER(N)
RY-1
RY-2
RY-3
RY-4
ST11
6042-000105
6042-000105
6042-000105
6042-000105
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
DB26-00066A
POWER(N)
DB39-01270A CONNECT WIRE
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
TRANS POWER
F701
Samsung Electronics
Specification
-,WW2-VE,-,8-PIN,230V/AC,16.5V/
DC,400mA,-,50hz,-,-,-,-,-,SSEC
(KET),TP,220V/50Hz,4mm,170mm,-,,SSEC
-,FH-51B,-,-,-,-,SSEC
-,A6063,25,15,15,-,-,SSEC
QTY
SA/SNA Remark
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
SNA
SNA
3-33
MAIN PCB : DB93-04128E

Location No.
Code No.
Description
D101
D102
D103
D104
D105
Q601
Q101
0402-000137
0402-000137
0402-000137
0402-000137
0402-000137
0501-000303
0501-000398
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
TR-SMALL SIGNAL
TR-SMALL SIGNAL
Q102
Q602
Q603
ICO1
ICO2
VA71
R103
R104
R105
R605
R606
R609
R610
R102
R608
R602
R603
R601
R101
R607
C107
C108
C102
C104
C106
CR71
1203-000429
1405-000154
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000429
2001-000591
2001-000734
2001-000780
2001-000780
2001-000855
2007-000290
2007-000290
2202-000128
2202-000128
2202-000780
2202-000780
2202-000780
2301-001363
IC-POSI.FIXED REG.
VARISTOR
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CHIP
R-CHIP
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-FILM,LEAD-PPF
XC71
C101
C103
C601
C105
BZ61
RY72
2301-001439
2401-000173
2401-000711
2401-002300
2401-003036
3002-001129
3501-001154
C-FILM,LEAD-PPF
C-AL
C-AL
C-AL
C-AL
BUZZER-PIEZO
RELAY-MINIATURE
RY73
RY71
F701
F702
CN72
3501-001268
3601-000263
3601-001209
3711-000262
J1
RELAY-POWER
FUSE-CARTRIDGE
FUSE-RADIAL LEAD
HEADER-BOARD TO
CABLE
CABLE
J2
CN73
3-34
Specification
QTY
SA/SNA Remark
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
1N4007,1KV,1A,DO-41,TP
KSA733,PNP,250mW,TO-92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
KSC945-Y,NPN,250mW,TO92,TP,120-240
7812,TO-220,3P,-,PLASTIC,11.5/
460Vdc,2500A,17.5x7.5mm,TP
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/4W,AA,TP,2.4X6.4MM
100ohm,5%,1/8W,TP,2012
100ohm,5%,1/8W,TP,2012
10nF,+80-20%,50V,Y5V,TP,2.5x4.
10nF,+80-20%,50V,Y5V,TP,2.5x4.
220nF,10%,275V,BK,18x10x15.8mm,15
1000uF,20%,35V,GP,TP,13x25,5
2200uF,20%,25V,GP,TP,16x25,7.5
47?F,20%,50V,GP,TP,6.3x11,5mm
10mS
10mS
12V,0.9W,25000mA,SPST,20mS,10mS
WHT
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SA
SA
1
1
1
1
SA
SNA
SNA
SNA
SNA
0.6mm,-,-
SNA
SNA
Samsung Electronics
MAIN PCB : DB93-04128E(cont.)

Location No.
Code No.
Description
J3
J4
J5
J6
J7
J8
TR-1
TR-2
TR-3
TR-4
4-WAY
FAN(H)
FAN(L)
POWER(N)
RY-1
RY-2
RY-3
RY-4
ST11
6042-000105
6042-000105
6042-000105
6042-000105
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
6042-001009
DB26-00066A
POWER(N)
DB39-01270A CONNECT WIRE
FAN(H)
DB39-01270B CONNECT WIRE
4-WAY
DB39-01270C CONNECT WIRE
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
TRANS POWER
F701
Samsung Electronics
Specification
-,WW2-VE,-,8-PIN,230V/AC,16.5V/
DC,400mA,-,50hz,-,-,-,-,-,SSEC
WW2-P/J,#1015 18 AWG,-,1P,,PINK,-,175022-1 (AMP),ST780400
WW2-P/J,#1015 18 AWG,-,1P,,BLK,-,175022-1 (AMP),ST780400
-,FH-51B,-,-,-,-,SSEC
-,A6063,25,15,15,-,-,SSEC
QTY
SA/SNA Remark
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
SNA
SNA
3-35
MAIN PCB : DB93-04181A

Location No.
D901
Q401
Q901
Q902
IC05
IC06
TURBO1
OPERATION1
TIMER1
RM01
IC07
R-OPTION3
R-OPTION4
R903
R301
R401
R403
R409
R501
R404
R405
R902
R901
R406
R407
R402
R905
R906
R909
R910
C301
C402
C403
C501
C503
C504
C901
C904
C905
C907
C401
C903
C902
C906
C909
X501
SWO1
CN61
CN43
CN44
3-36
Code No.
Description
0401-000133 DIODE-SWITCHING
Specification
RLS4148,75V,150mA,LL-34,TP
2SC2412K,NPN,200mW,SOT23,TP,180-390
0504-000001 TR-DIGITAL
DTA114EKA,PNP,200mW,10K/
10K,SOT-23,TP
0504-000001 TR-DIGITAL
DTA114EKA,PNP,200mW,10K/
10K,SOT-23,TP
0506-000175 TR-ARRAY
2003,NPN,7,1W,SOP-16,ST,1000
0506-000175 TR-ARRAY
2003,NPN,7,1W,SOP-16,ST,1000
0601-000360 LED
ROUND,RED,3mm,635nm,3.2x4.5mm
0601-001375 LED
ROUND,GRN,3mm,570nm,3.8x5.3mm
0601-001375 LED
ROUND,GRN,3mm,570nm,3.8x5.3mm
0609-001204 Module Remocon
HORIZONTAL,6.5mm,TR
1103-001016 IC-EEPROM
93C56,256x8/
128x16Bit,SOP,8P,5x4mm,-,2.7/5.5V,-,-,40to+85C,10uA,-,TP
2007-000029 R-CHIP
0ohm,5%,1/8W,TP,2012
2007-000029 R-CHIP
0ohm,5%,1/8W,TP,2012
2007-000300 R-CHIP
10Kohm,5%,1/8W,TP,2012
2007-000468 R-CHIP
1Kohm,5%,1/8W,TP,2012
2007-000468 R-CHIP
1Kohm,5%,1/8W,TP,2012
2007-000468 R-CHIP
1Kohm,5%,1/8W,TP,2012
2007-000468 R-CHIP
1Kohm,5%,1/8W,TP,2012
2007-000477 R-CHIP
1Mohm,5%,1/8W,TP,2012
2007-000766 R-CHIP
330ohm,5%,1/8W,TP,2012
2007-000766 R-CHIP
330ohm,5%,1/8W,TP,2012
2007-000872 R-CHIP
4.7Kohm,5%,1/8W,TP,2012
2007-000947 R-CHIP
47ohm,5%,1/8W,TP,2012
2007-001067 R-CHIP
6.8Kohm,1%,1/8W,TP,2012
2007-001067 R-CHIP
6.8Kohm,1%,1/8W,TP,2012
2007-001071 R-CHIP
6.8Kohm,5%,1/8W,TP,2012
2007-001318 R-CHIP
1Kohm,5%,1/4W,TP,3216
2007-001318 R-CHIP
1Kohm,5%,1/4W,TP,3216
2007-001318 R-CHIP
1Kohm,5%,1/4W,TP,3216
2007-001318 R-CHIP
1Kohm,5%,1/4W,TP,3216
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000192 C-CER,CHIP
100nF,+80-20%,50V,Y5V,2012
2203-000260 C-CER,CHIP
10nF,10%,50V,X7R,2012
2203-000260 C-CER,CHIP
10nF,10%,50V,X7R,2012
2203-000444 C-CER,CHIP
1nF,10%,50V,X7R,2012
2203-000444 C-CER,CHIP
1nF,10%,50V,X7R,2012
2401-003107 C-AL
47uF,20%,16V,GP,TP,5x7,5
2802-001198 RESONATOR-CERAMIC 10MHZ,0.5%,BK,8X3X5.5MM
3404-001220 SWITCH-TACT
12V,50mA,160gf,6.1x6.1x5.0mm,SPST
BOX,5P,1R,2.5MM,ANGLE,SN,WHT
CABLE
BOX,4P,1R,2mm,ANGLE,SN,NTR
CABLE
BOX,3P,1R,2.5MM,ANGLE,TIN,BLU
CABLE
QTY
SA/SNA Remark
1
1
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
Samsung Electronics
MAIN PCB : DB93-04181A(cont.)

Location No.
IC04
Code No.
Description
DB09-00516A IC MICOM
DB41-00510A PCB-MAIN
CN02
DB93-04187A ASSY-CONNECT WIRE
Samsung Electronics
Specification
S3C848AXZZ-QT8A,,64P,+5V,10MHz,STM-0648-OA, ROM
Size: 48K bytes,8BIT,8BIT,QFP,QFP,,8BIT,-40~+85
WW2-P/J,FR-4,TWOLAYER,VERSION1,T1.6,65*80,-,-,,VE,SSEC
WW2,,26AWG,12-PIN,250mm
QTY
SA/SNA Remark
SA
SNA
SNA
3-37
9. Circuit Descriptions
9-1 PCB Circuit Descriptions
9-1-1 Main PCB
INDOOR TEMPERATURE SENSOR

INPUT PART
STEP MOTOR CONTROL PART
REMOTE RECEIVER PART
DISPLAY CONTROL PART
MOTOR RPM FEEDBACK
Samsung Electronics
9-1
PCB Circuit Descriptions
PCB Circuit Descriptions
9-1-2 Power PCB
INDOOR FAN CONTROL PART
AC/DC PART
ZERO CROSSING PART
LOAD DRIVE RELAY PART
BUZZER DRIVE PART
Samsung Electronics
9-2
9-2 Refrigerating Cycle Diagram
Outdoor Unit
Indoor Unit
Capillary tube
T1
2 way valve
Note
Check valve
Liquid side
Heat
Exchanger
(Condenser)
Cross Fan
Heat
Exchanger
(Evaporator)
Propeller Fan
Capillary tube
T2
Gas side
3 way valve
4 way valve
Cooling
Compressor
9-4
Heating
Gas Leak Check Point
Samsung Electronics
11. Operating Instructions

11-1 Name of Each Part
11-1-1 Indoor Unit
The design and shape are subject to change according to the model.
Air Inlet
Temperature sensor
Power(On/Off) button
Air lter
(under the grille)
Air ow blades
(outlet)
Operation indicator
(GREEN)
Timer indicator
(GREEN)
Turbo indicator
(RED)
Power(On/Off) button
11-1
Samsung Electronics
11-1-2 Outdoor Unit
H/P
Air Inlet(Rear)
Air Outlet
Connection Valve
C/O
Air Inlet(Rear)
Air Outlet
Connection Valve
Samsung Electronics
11-2
11-2 Main Function

11-2-1 Basic Function
Mode
Explanation
Auto Mode
Press the
button on the remote control until
Cool Mode
Press the
Press the
is displayed.
is displayed.
is displayed.
button to select the fan speed until the required setting
Automatic (rotated :
Low
Medium
High
Maximum
11-3
Remark
Dry Mode
Press the
is displayed.
Fan Mode
Press the
is displayed.
Samsung Electronics
Operating Instructions
11-2-2 Applied Function

Mode
Turbo Function
Explanation
Press the
Remark
button.
After 30 minutes, the air conditioner is reset automatically to the

previous setting.
You can select the Turbo function in the Auto, Cool and Heat mode.
If you select this function in the Dry or Fan mode, the mode
changes to the Auto mode.
Samsung Electronics
11-4
11-3 Wireless Remote Control-Buttons and Display
Remote control
transmission indicator
Operating mode
AUTO, COOL, DRY,
FAN, HEAT)
Temperature setting
Turbo mode
Good Morning mode
Fan speed
Air ow direction
On Timer setting
Off Timer setting
Mode selection button

(AUTO, COOL, DRY,
FAN, HEAT)
Temperature adjustment
buttons
Turbo button
Fan speed adjustment
button
Swing button
On Timer button
Off Timer button
Battery discharge indicator

Good Morning button
11-5
On/Off &
Timer Set/Cancel button
Samsung Electronics
14. Reference Sheet

14-1 Index for Model Name
Private Expert Model for Split Type and Europe Type
Model Code
Model name
18
Product
Cooling Only
AS
Heat Pump
AQ
Inverter
Inverter
14-1
Capacity
Btu
Project
Serial Version
BIG
New
Forte
1st VE Model
GP
2nd VE Model
HB
WW Premium
Moderato
Neo Classic
Deluxe Classic
Presto
Tiffany
Vivace
WW
Tsar
Buyer Code
MIDDLE EAST
MID
RUSSIA
SER
Samsung Electronics
14-2 Refrigerant Pressure during the Charging

Outdoor Unit Temperature
Low Pressure kg/cm2(PSIC)
Less than 20C
4.5 ~ 4.7(64~67)
Less than 24C
4.7 ~ 4.8(67~68)
Less than 28C
4.8 ~ 4.9(68~70)
Less than 32C
4.9 ~ 5.0(70~71)
Less than 36C
5.0 ~ 5.1(71~73)
Less than 40C
5.1 ~ 5.2 (73~74)
Less than 44C
5.2 ~ 5.3 (74~75)
14-3 Pressure & Capacity mark

Power/Heat
W
cal/s
kcal/h
Btu/h
HP
kg.m/s
lbm/s
0.23885
0.85985
3.4121
0.001341
0.10197
0.73756
4.1868
3.6
14.286
0.0056146
0.42693
3.088
1.163
0.27778
3.9683
0.0015596
0.11859
0.85778
0.29307
0.06999
0.252
3.9302x10
0.029885
0.21616
745.7
178.11
641.19
2,544.4
76.04
550
9.8067
2.3423
8.4322
33.462
0.013151
7.233
1.3558
0.32383
1.1658
4.6262
0.0018182
0.13826
Samsung Electronics
-4
14-2
14-4 Q & A for Non-trouble

Classification
Cooling
Class
Q
The cooling is weak.
When it is hot outside, its cooling capacity decreases due to the increase of the ambient temperature.
When the dust filter gets blocked or warm outside air gets in, the cooling capacity will decrease. So,
make sure to clean the dust filter frequently, prevent heat loss by closing the doors and insulate the
cooling area by using curtains, blinds, shades or window tinting.
The cooling is good generally. But, it gets weak when it is considerably hot.
It occurs when the outdoor unit is exposed to direct sun light and heat-up air is not ventilated well.
So, set up a sunblind over the outdoor unit and keep stuff away from the unit to increase the ventilation.
When the cooling capacity decreases during a heat wave, clean the heat exchanger of the outdoor unit or
spray some cold water to the heat exchanger to increase the cooling capability.
The cooling is weak. Does it need refrigerant charging?
It is not correct charging refrigerant regularly. Except that you have moved in several times or the
connection pipes are broken, the refrigerant does not run low. So, when refrigerant is additionally
charged, it could be costly and cause a product's failure. When the refrigerant leaks, all of it will escape
in a short time resulting in cooling failure and no water coming out of the drain hose. So, if water comes
out from the drain hose, it indicates the normal operation of the product and it does not need refrigerant
charging.
It fails to do cooling.
When the air conditioner is set to Ventilation or the desired temperature is set higher than the current
temperature, it fails to do cooling. In this case, select Cooling or set the desired temperature lower.
It floods the floor.
Place the drain hose properly. When it is not placed properly, the drain water would flow back flooding
the floor. So, straighten out the drain hose for the water to be drained well.
Water drips at the drain connection (service valve) of the outdoor unit.
When a glass bottle is taken out of the refrigerator, moisture gets condensed on its surface due to the
temperature differences. The same principle applies to the air conditioner. When cold refrigerant goes
through the copper tube, moisture gets condensed on the surface of the tube and the connection areas.
To prevent the water condensation, the pipes are insulated. But, the connection areas of the outdoor unit
are not insulated for the purpose of maintenance or repair, and water gets condensed due to the temperature differences and drips down. Generally, it evaporates right away. But, when it drips much during
muggy days, put a water pan on the floor.
It leaks even though a drain pump is used.
It occurs when the drain pump is plugged out or it is out of order. Check the power of the drain pump
and the position of the drain hose, and when the pump is faulty, contact the drain pump manufacturer.
Samsung Electronics do not manufacture drain pumps. So, we are not able to correct the drain pump
problems.
Whenever the air conditioner is turned on, it irritates my eyes and gives me a headache.
There are no components in the air conditioner irritating the eyes and sending out chemical smells.
But, when the air conditioner is turned on, other smell sources are sucked into the air conditioner and get
out of it. So, find and root out the smell sources. Generally, it occurs at a interior renovated place,
a pharmacy, a gasoline handling place, a tire shop, a second-hand book shop or an electronic
component handling place; when its chemical or musty smells are sucked in and sent out, it can be misled
that the air conditioner generates them. So, find and root out the problem or refresh the room frequently.
Leakage
Smells
14-3
Description
Samsung Electronics
Q & A for Non-trouble(cont.)

Classification
Smells
Class
Description
Whenever the air conditioner is turned on, it stinks.
There are no components in the air conditioner sending out chemical smells. But, when the air conditioner
is turned on, other smell sources are sucked into the air conditioner and get out of it. So, find and root out
the smell sources. Generally, when the drain hose is taken out to the washing room or there are sources
of smells such as a diaper bin, a shoe shelf or a socks bin, bad smells generate. Also, it occurs where glass
cleaners or air fresheners are used; when they are sucked in interacting with dusts and moistures inside,
bad smells generate. These kinds of organic materials noxious to human bodies. So, we recommend
against the use of them.
Whenever the air conditioner is turned on, it smells sour.
When the room is papered recently, its paste smells would be sucked inside. Also, when the air conditioner is installed in the study room of young boys loving sweat-generating activities such as the basketball,
excessive sweats evaporate and get sucked into the air conditioner resulting in bad smells. So, find and
root out the problem or refresh the room frequently.
Whenever the air conditioner is turned on, it smells musty.
It is due to the improper keeping of the product after its use. When keeping the product, dry up the
inside with the operation of Ventilation to prevent must. When the product is kept without drying up the
inside with Ventilation, mold would grow inside resulting in must. So, open the windows and switch on
the Ventilation function to get rid of the saturated smell inside.
Whenever the air conditioner is turned on, it sends out bad smells such as stale smells.
It occurs generally when there are pet animals in the house. Their smells stay at the same place.
But, when the air conditioner is turned on, the air gets circulated resulting in the circulation of the smells.
So, find and root out the problem or refresh the room frequently.
It sends out bad smells.
When the air filter is filthy, it could send out bad smells. So, clean the filter and ventilate the room with
the windows open while operating the Ventilation function.
It won't start.
There is a power failure or it is plugged out. Also, check if the power distribution panel is switched off.
It goes off during operation.
When the hot air does not escape properly, it goes off during operation. It occurs when it does not
ventilate properly because the outdoor unit is covered, the back of the outdoor unit is blocked by a
cardboard or a plywood panel, and the front of the outdoor unit is blocked by the closed window or
other obstacles. Clear the above obstacles from the outdoor unit.
It generally works properly. But, when it's considerably hot, it goes off during operation.
It occurs when the outdoor unit is exposed to direct sunlight and the hot air does not escape properly.
Set up a sun blind over the outdoor unit and clear the neighboring obstacles from the outdoor unit to
provide good ventilation. When it goes off frequently during a heat wave, it would prevent the turn-off and
increase the cooling capacity cleaning the outdoor unit or spraying some water to the heat exchanger.
Operation
Samsung Electronics
14-4
Q & A for Non-trouble(cont.)

Classification
Operation
Class
Q
The remote controller won't operate.
When the batteries run out or the transmitter or receiver of the remote controller is blocked by obstacles,
change the batteries or keep the obstacles away from the controlling area. Also, the remote controller may
not work under intensive light from a 3-wave length lamp or a neon sign due to the EMI. In this case, take
the remote controller closer to the receiver.
Who installs the air conditioner? (Relocation/Re-installation)
When relocating or re-installing the air conditioner, make sure to contact Samsung Electronics Service
Center or Authorized Service Agent and have them to do the job. (If not, it could cause personal injury or
product damage.)
The cost for the relocation/re-installation of the air conditioner is subject to the customer's expense.
There is a cost table. But, our service engineer needs to visit to total up the cost correctly.
When you move in, make sure to contact Samsung Electronics Service Center or Authorized Service Agent
in advance to streamline the process.
Is it possible to install the outdoor unit outside?
It is possible to install it at a designated place in the apartment or on the rooftop nearby.

But, it's illegal hanging an angle iron case with the outdoor unit in it outside the apartment.
Also, it is illegal obstructing passers-by with the outdoor unit installed outside.
What can be done to install the outdoor unit facing the road because it is a commercial building?
The following is an excerpt from Building Code going into effect from JUNE 1st 2005. "The exhaust pipe of
a cooling or ventilation facility installed in a building adjacent to the streets of commercial or residential
areas shall be installed higher than 2m to prevent the exhaust air from blowing directly to passers-by and
the current facilities shall be corrected by MAY 31st 2005." So, please install it higher than 2m or not to blow
the hot exhausting air directly to passers-by.
What about installing a windscreen during installation not to blow hot air directly to passers-by?
When the hot air from the front of the outdoor unit is blocked, the product's performance will be
affected and it will fail to operate properly. So, keep it at least 300mm away from its surrounding walls and
give it good ventilation.
Installation
14-5
Description
Samsung Electronics
14-5 Cleaning/Filter Change

14-5-1 Cleaning Your Air Conditioner
For the best use of your air conditioner, you must clean it every 2 weeks regularly to remove the dust that accumulates on the air filter.
Before cleaning your air conditioner, ensure that you have switched off the breaker used for the unit.
1. Slide the lower front grille down.

2. Slide the upper front grille up slightly, then open the grille by pulling right
and left sides of the grille.
3. Disassemble the upper front grille by opening the grille completely.
4. Lift out the bottom edge of the air filters and pull down to release them.
5. Remove all dust on the air filters with a vacuum cleaner or brush.
6. When you have finished, insert the top part of the filters into their slot
and push down on the bottom edge until they click into place.
Front grille
Air lter
7. Clean the front grille with a damp cloth and mild detergent
(do NOT use benzene, solvents or other chemicals).
8. Fix the left side of grille support, then insert the right side of grille support.
Body groove
Body
Front grille
Hook
Body
Note : If you have not used the air conditioner for a long period of time, set the fan
going for three to four hours to dry the inside of the air conditioner thoroughly.
To close the upper front grille completely after cleaning filters, turn on and turn off the air conditioner.
Samsung Electronics
14-6
Reference Sheet
14-5-2 Cleaning Deodorizing and Bio Filters (Option)

To remove minute dust particles and odors, deodorizing and Bio filters are installed in the air conditioner.
You should clean the filters every 3 months.
1. Open the upper front grille by pulling right and left sides of the grille.
Deodorizing Filter
2. Pull out the deodorizing and Bio filters.

3. Wash the filters with clean water, then dry them in the shade.
4. Insert the filters into the original position.
Note : You can change the position of filters with each other.
Bio Filter
5. Close the front grille.
14-7
Samsung Electronics
14-6 Installation
14-6-1 Before Installation
Keep the air conditioner outlet and inlet free from its surroundings.
In case of installation, keep the symmetry and fix it to prevent vibration.
The pipe length shall meet the standard as far as possible.
14-6-2 Installation Procedure

Location
Install the product in an area to guarantee the best cooling effect, convenience of piping and electric work, and inexistence of
vibration or wind.
Wall Drilling
Drill the wall downward in a diameter of 60 to 65mm.
Fixing Indoor Unit & Outdoor Unit

Fix the air conditioner indoor unit securely to the wall. Secure the outdoor unit in a suitable position.
Pipe Spooling & Connecting

You shall cut the pipe with a pipe cutter and grind all the burrs of the cut surface.
Pipe expansion may continue until the pipe surface becomes uneven or torn apart.
Be sure to use a torque wrench to tighten pipes or flare nuts.
<Torque & Depth>
Outer Diameter(D)
Torque(kgfcm)
Depth(A)
6.35mm(1/4")
140~170
1.3mm
9.52mm(3/8")
250~280
1.8mm
12.70mm(1/2")
380~420
2.0mm
15.88mm(5/8")
440~480
2.2mm
19.05mm(3/4")
990~1,210
2.2mm
D
A
Leak Test
Put an inert gas like nitrogen in the outdoor unit pipe and put soap bubbles or other test liquids on the pipe surface for the
leak test.
Drain Hose Connecting

Install the drain hose downward to drain water naturally. Be sure to pour water into the hose to check if it drains well.
Electric & Earth Work

Electric and earth work shall meet the "Electric Facility Technology Standard" and the "Internal Wire Regulation" of the Electric
Business Laws.
Inspection & Trial Run

Upon completion of the tests, you shall make a trial run while you explain the main functions of the air conditioner to finish the
installation.
Samsung Electronics
14-8
14-7 Installation Diagram of Indoor Unit and Outdoor Unit

14-7-1 Air-Purge Procedure
1) Connect each assembly pipe to the appropriate valve on
the outdoor unit and tighten the flare nut.
Indoor unit
Outdoor unit
Gas pipe side
Liquid pipe side D
2) Connect the charging hose of low pressure side of

manifold gauge to the packed valve having a
service port (3/8" Packed valve) as shown at the
figure.
3) Open the valve of the low pressure side of manifold

gauge counter-clockwise.
4) Purge the air from the system using vacuum pump for
about 30 minutes.
- After that, please recheck that pressure is stabilized.
- Close the valve of the low pressure side of manifold
gauge clockwise.
- Remove the hose of the low pressure side
of manifold gauge.
5) Set valve cork of both liquid side and gas side of packed
valve to the open position.
6) Mount the valve stem nuts to the 2 way and

3 way valve. And mount the service port cap to
3 way valve.
Vacuum Pump
Valve stem
Stem cap
7) Check for gas leakage.

- At this time, especially check for gas
leakage from the 3 way valve's stem nuts,
and from the service port cap.
A
(gas)
B
(liquid)
14-9
Samsung Electronics
Reference Sheet
14-7-2 "Pump down" Procedure

Pump down will be carried out when an evaporator is replaced or when the unit is relocated in another area.
1) Remove the caps from the 3 way valve and the

3 way valve.
2) Turn the 3 way valve clockwise to close and

connect a pressure gauge (low pressure side)
to the service valve, and open the 3 way valve
again.
3 way Valve
2 way Valve
3) Set the unit to cool operation mode.

(Check if the compressor is operating.)
4) Turn the 3 way valve clockwise to close.
5) When the pressure gauge indicates "0" turn the

3 way valve clockwise to close.
6) Stop operation of the air conditioner.
7) Close the cap of each valve.
Relocation of the air conditioner

Refer to this procedure when the unit is relocated.
Carry out the pump down procedure (refer to the details of pump down).
Remove the power cord.
Disconnect the assembly cable from the indoor and outdoor units.
Remove the flare nut connecting the indoor unit and the pipe.
At this time, cover the pipe of the indoor unit and the other pipe using a cap or vinyl plug to avoid foreign material
entering.
Disconnect the pipe connected to the outdoor unit.
At this time, cover the valve of the outdoor unit and the other pipe using a cap or vinyl plug to avoid foreign
material entering.
Make sure you do not bend the connection pipes in the middle and store together with the cables.
Move the indoor and outdoor units to a new location.
Remove the mounting plate for the indoor unit and move it to a new location.
Samsung Electronics
14-10
ELECTRONICS
This Service Manual is a property of Samsung Electronics Co., Ltd.

Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.
Samsung Electronics Co., Ltd. Sep. 2006.

Printed in China.
Code No. DB98-00000A(1)
1. Precautions
1-1 Installing the air conditioner
Users should not install the air conditioner by themselves.
Ask the dealer or authorized company to install the air conditioner except the window-type air conditioner in U.S.A and Canada.
If you dont install the air conditioner properly, it may cause a fire, a water leakage or an electric shock.
You must install the air conditioner according to the national wiring regulations and safety regulations.
Install the indoor unit higher than 2.5m from the floor to avoid the injury caused by the operation of the fan.
(except the window-type air conditioner)
The manufacturer is not responsible for any accidents or injury caused by an incorrect installation.
When installing the built-in type air conditioner, keep all electric cables such as the power cable and the connection cord in pipes,
ducts, or cable channels to protect them from the danger of impact or any other incidents.
1-2 Power supply and circuit breaker

If the power cord of the air conditioner is damaged, it must be replaced by the manufacturer or a qualified person in order to avoid
a hazard.
The air conditioner must be plugged into an independent circuit if applicable or connect the power cable to the auxiliary circuit
breaker.
An all pole disconnection from the power supply must be incorporated in the fixed wiring with a contact opening of >3mm.
Do not extend an electric cord to the air conditioner.
The air conditioner must be plugged in after you complete the installation.
1-3 During operation

Do not repair the air conditioner at your discretion.
It is recommended to contact a service center directly.
Never spill any kind of liquid on the air conditioner.
If this happens, turn off the air conditioner and contact an authorized service center.
Do not insert anything between the airflow blades to prevent damage of the inner fan and consequent injury.
Keep children away from the air conditioner.
Do not place any obstacles in front of the air conditioner.
Do not spray any kind of liquid into the indoor unit. If this happens, turn off the air conditioner and contact a service center.
Make sure that the air conditioner is well ventilated at all times:
Do not place a cloth or other materials over it.
Remove the batteries if you dont use the remote control for a long time. (If applicable)
Use the remote control within 7 meters from the indoor unit. (If applicable)
Samsung Electronics
1-1
1-4 Disposing of the unit

Before throwing out the air conditioner, remove the batteries from the remote control.
When you dispose of the air conditioner, consult your dealer. If pipes are removed incorrectly, refrigerant may blow out and cause
air pollution. When it contacts with your skin, it can cause skin injury.
The package of the air conditioner should be recycled or disposed of properly for environmental reasons.
1-5 Others
1-2
Never store or load the air conditioner upside down or sideways to prevent the damage to the compressor.
Young children or infirm persons should be always supervised when they use the air conditioner.
Max current is measured according to IEC standard for safety.
Current is measured according to ISO standard for energy efficiency.
Samsung Electronics

AQ 09 12 FAN Service Manual PDF

Uploaded by

Copyright:

Available Formats

AQ 09 12 FAN Service Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AQ 09 12 FAN Service Manual PDF

Uploaded by

Copyright:

Available Formats

SPLIT-TYPE AIR CONDITIONER

THE FEATURE OF PRODUCT

Good Morning Mode

Silver Nano Evaporator

Anti-Bacterial Cross Fan

For more information, Please access to our service web site(http://itself.sec.samsung.co.kr)

Operating Instructions and Installation

1-2 Power supply and circuit breaker ..........................................................................................................

1-3 During operation

1-4 Disposing of the unit .................................................................................................................................

1-5 Others .............................................................................................................................................................

12. Product Specifications ........................................................................................................................ 2-1

2-2 Product Specifications

2-3 The Comparative Specifications of Product .......................................................................................

2-4 Accessory and Option Specifications ...................................................................................................

13. Alignment and Adjustments ......................................................................................................... 3-1

3-2 Error Mode and Check Method ..............................................................................................................

3-3 Setting Option Setup Method ................................................................................................................

14. Disassembly and Reassembly ...................................................................................................... 4-1

4-2 Outdoor Unit

15. Exploded Views and Parts List ..................................................................................................... 5-1

5-2 Outdoor Unit ................................................................................................................................................

5-3 Assy Control In ............................................................................................................................................

16. Electrical Parts List

18. Schematic Diagram

19. Circuit Descriptions ............................................................................................................................... 9-1

9-2 Refrigerating Cycle Diagram ...................................................................................................................

Operating Instructions and Installation

11-3 Wireless Remote Control-Buttons and Display ............................................................................... 11-5

12. Troubleshooting ...................................................................................................................................... 12-1

13. Block Diagram ............................................................................................................................................ 13-1

14-4 Q & A for Non-trouble ............................................................................................................................. 14-3

Silver Nano Evaporator

Anti-Bacterial Cross Fan

2-2 Product Specifications

Power POWER FACTOR COOLING

NUMBER OF CORE WIRRE

Outer Dimension WxHxD

Freezer Oil Capacity

INDOOR UNIT:DB27C/WB19C OUTDOOR UNIT:DB35C WB 24C

Maximum Operation Condition

INDOOR UNIT:DB32C/WB23C OUTDOOR UNIT:DB43C WB 26C

Power POWER FACTOR COOLING

NUMBER OF CORE WIRRE

Outer Dimension WxHxD

NOC & Suniso-4GSD

NOC & Suniso-4GSD

Freezer Oil Capacity

INDOOR UNIT:DB27C/WB19C OUTDOOR UNIT:DB35C WB 24C

Maximum Operation Condition

INDOOR UNIT:DB29C/WB19C OUTDOOR UNIT:DB46C WB 24C

2-3 The Comparative Specifications of Product

Air Purifying System

2-4 Accessory and Option Specifications

Batteries for Remote Control

3-wire Assembly Cable

5-wire Assembly Cable

Assembly Pipe, 6.35mm

Assembly Pipe, 9.52mm