Scribd
Upload
160 views10 pages

Eg07 Section Views

Sectional views show internal details of a part using imaginary cutaways. There are several types of section views including full sections, half sections, offset sections, broken-out sections, aligned sections, revolved sections, and removed sections. The cutting plane line indicates where the imaginary cut is made and section lining is used to represent the cut surface. Section views improve upon traditional orthographic views by making internal features and details easier to visualize.

Uploaded by

Hasmaye Pinto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
160 views10 pages

Eg07 Section Views

Sectional views show internal details of a part using imaginary cutaways. There are several types of section views including full sections, half sections, offset sections, broken-out sections, aligned sections, revolved sections, and removed sections. The cutting plane line indicates where the imaginary cut is made and section lining is used to represent the cut surface. Section views improve upon traditional orthographic views by making internal features and details easier to visualize.

Uploaded by

Hasmaye Pinto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

35

EG07 Sectional Views


Sectional views, commonly called sections, are used to show interior detail that is too
complicated to be shown clearly and dimensioned by the traditional orthographic views and
hidden lines. A sectional view is obtained making an imaginary cut through the part, and by
drawing the features on the cut surface, as shown in Figure 18. In a drawing, the exposed or cut
surfaces are identified by section lining, or crosshatching. Section views show internal part detail
as solid lines instead of hidden lines, which improve communication. Hidden lines and details
behind the cutting-plane line are usually omitted unless they are required for clarity. A sectional
view can sometimes replace one of the regular views, for example, a regular front view as shown
in Figure 19.

Figure 18. Cutting a part and showing a section view.

Figure 19. A section drawing.

36
The Cutting-Plane Line
A cutting-plane line indicates where the imaginary cutting takes place. The position of
the cutting plane is indicated, when necessary, on a view of the object or assembly by a cuttingplane line, as shown in Figure 20. The ends of the cutting-plane line are bent at 90 degrees and
terminated by arrowheads to indicate the direction of sight for viewing the section. Cutting
planes are not shown on sectional views. The cutting-plane line may be omitted when it
corresponds to the centerline of the part or when only one sectional view appears on a drawing.

Figure 20. A section drawing.


If two or more sections appear on the same drawing, the cutting-plane lines are identified
by two identical large, single-stroke, Gothic letters. One letter is placed at each end of the line.
Sectional view subtitles are given when identification letters are used and appear directly below
the view, incorporating the letters at each end of the cutting-plane line, thus: SECTION A-A or,
abbreviated, SECT A-A.

Section Lining
Section lining indicates the surface that has been cut and makes it stand out clearly.
Section lines usually consist of thin parallel lines, drawn at an angle of approximately 45 degrees
to the principal edges or axis of the part, as in Figure 21.
Because the exact material specifications for a part are usually given elsewhere, the
general use section lining (i.e., the 45 degree solid parallel lines) is recommended for general use.
When it is desirable to indicate differences in materials, other symbolic section lines are used,
such as those shown in Figure 22. If the part shape would cause section lines to be parallel or
nearly parallel to one of the sides or features of the part, an angle other than 45 degrees can be
chosen.

37

Figure 21. Section lining.

Figure 22. Symbolic section lining


The spacing of the hatching lines is uniform to give a good appearance to the drawing.
The pitch, or distance, between lines varies from .06 to .18 inch, depending on the size of the area
to be sectioned. Section lining is similar in direction and spacing in all sections of a single
component. Wood and concrete are the only two materials usually shown symbolically. When
wood symbols are used, the direction of the grain is shown.

38
Types Of Sections
Full Sections
When the cutting plane extends entirely through the object in a straight line and the front
half of the object is theoretically removed, a full section is obtained, Figure 23 (B). This type of
section is used for both detail and assembly drawings. When the cutting plane divides the object
into two identical parts, it is not necessary to indicate its location. However, the cutting plane
may be identified and indicated in the usual manner to increase clarity.

Figure 23. Full section


Half Sections
A symmetrical object or assembly may be drawn as a half section, Figure 24 (C),
showing one half up to the center line in section and the other half in full view. A normal
centerline is listed on the section view. The wording, half section, can be confusing because one
thinks of showing half the part. Remember, a half section shows one-fourth of the part, not onehalf!

39

Figure 24. Half section


The half section drawing is not normally used where the dimensioning of internal
diameters is required. This is because many hidden lines would have to be added to the portion
showing the external features. This type of section is used mostly for assembly drawings where
internal and external features are clearly shown and only overall and center-to-center dimensions
are required.
Offset Sections
In order to include features that are not in a straight line, the cutting-plane line may be
offset or bent, so as to include several planes or curved surfaces, Figure 25. An offset section is
similar to a full section in that the cutting plane extends through the object from one side to the
other. The change in direction of the cutting-plane line is not shown on the sectional view.

40

Figure 25. An offset section

Additional Section Views


There are 7 types of section views. So far, we have discussed three: full-section, halfsection, and offset section. The other four are: broken-out section, revolved section, revolved
section, and aligned section.
Broken-out Section
When certain internal and external features of an object can be shown without drawing
another view, broken-out and partial sections are used, Figure 26. A cutting-plane line or a break
line is used to indicate where the section is taken. The break line is normally a jagged line, which
better indicates the break. Broken-out sections save drawing time and drawing space. Most CAD
systems have a freehand sketching tool to create the break line.

41

Figure 26. Broken-out Section


Aligned Section
A aligned section is not a true projection of the cut surface. It is often used when a part
contains webs, ribs, spokes, or similar features. It revolves or aligns special part features to
clarify them or make them easier to represent in section. One can conceptually think about a
aligned section as a specialized offset section, Figure 27. The cutting plane can be bent to pass
through all of the nonaligned features in the un-sectioned view. Another example is shown in
Figure 28.

Figure 27. Aligned section

42

Figure 28. Aligned section


Revolved Sections
A revolved section is made by revolving the cross-section view 90 degrees about an axis
of revolution and superimposing the section view on the orthographic view. Visible lines adjacent
to the revolved view can be either drawn or broken out using conventional breaks, as shown in
Figure 29 (B). When the revolved view is superimposed on the part, the original lines of the part
behind the section are deleted. The cross section is drawn true shape and size, not distorted to fit
the view. The axis of revolution is shown on the revolved view as a centerline. Another example
is shown in Figure 30.
Revolved sections are useful for describing a cross section without having to draw
another view. In addition, these sections are especially helpful when a cross section varies or the
shape of the part is not apparent from the given orthographic views.

43

Figure 29. Revolved section

Figure 30. Revolved section


Removed Section
A removed section differs from the revolved section in that the section is removed to an
open area on the drawing instead of being drawn directly on the view. Removed sections are
used when there is not enough room on the orthographic view for a revolved section. Removed

44
sections are used to show the contours of complicated shapes, such as the wings and fuselage of
an airplane, blades for jet engines or power plant turbines, and other parts that have continuously
varying shapes. Frequently, the removed section is drawn to an enlarged scale for clarification
and easier dimensioning, Figure 31 and Figure 32

Figure 31. Removed section

Figure 32. Removed section


Normally, the cross-section view is drawn adjacent to the orthographic view and close to
the position of the cutting plane, which is identified with either a center line or a cutting plane
line. If a number of removed sections are done on a part, cutting plane lines may be drawn with
labels to clarify the position from which each section is taken. The removed section view is then
labeled, such as SECTION A-A as shown in Figure 32, to correspond to the labeled cutting plane
line.

You might also like