Panel LG Display Lp156wh4-Tln1 2

www.panelook.
com
Global LCD Panel Exchange Center
LP156WH4
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
) Preliminary Specification
( ) Final Specification
Title
Customer
15.6 HD TFT LCD

SUPPLIER
General
*MODEL
MODEL
Suffix
LG Display Co., Ltd.

LP156WH4
TLN1
*When you obtain standard approval,

please use the above model name without suffix
APPROVED BY
APPROVED BY
SIGNATURE
SIGNATURE
C. I. Kim / S.Manager
/
REVIEWED BY
B. T. Jang / Manager
B. D. Jun / Manager
/
PREPARED BY
C. H. Yun / Engineer
C.K.D / Engineer
Products Engineering Dept.

LG Display Co., Ltd
Please return 1 copy for your confirmation with

your signature and comments.
Ver. 1.0
Feb. 28, 2012
1 / 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
www.panelook.com
LP156WH4
Contents
No
ITEM
Page
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
3-1
ELECTRICAL CHARACTREISTICS
3-2
INTERFACE CONNECTIONS
3-3
LVDS SIGNAL TIMING SPECIFICATION
3-3
SIGNAL TIMING SPECIFICATIONS
11
3-4
SIGNAL TIMING WAVEFORMS
11
3-5
COLOR INPUT DATA REFERNECE
12
3-6
POWER SEQUENCE
13
6-7
8
9-10
OPTICAL SFECIFICATIONS
14-16
MECHANICAL CHARACTERISTICS
17-20
APPENDIX. LPL PROPOSAL FOR SYSTEM COVER DESIGN
21-23
A
6
RELIABLITY
INTERNATIONAL STANDARDS
24
7-1
SAFETY
25
7-2
EMC
25
7-3
ENVIRONMENT
25
PACKING
8-1
DESIGNATION OF LOT MARK
26
8-2
PACKING FORM
26
8-3
LABEL DESCRIPTION
27
9
A
Ver. 1.0
PRECAUTIONS
28-29
APPENDIX. Enhanced Extended Display Identification Data
30-32
Feb. 28, 2012
2 / 32
www.panelook.com
LP156WH4
RECORD OF REVISIONS
Revision No Revision Date
Page
0.0
Jul. 21, 2011
0.1
Aus. 31. 2011
30-32
0.2
Oct. 12. 2011
Jan. 05. 2012
0.0
EDID Update
0.0
14
Update Color coordinates
0.0
15
Update scale
18-19
Update LCM Drawing
27
Update Label drawing
EDID Update
15
30-32
-
1.0
Ver. 1.0
Feb. 28, 2012
EDID
ver
First Draft (Preliminary Specification)
30-32
1.0
Description
14
Update Gray scale
1.0
EDID Update
Final Draft
Optical Characteristics
Feb. 28, 2012
1.0
3 / 32
www.panelook.com
LP156WH4
1. General Description
The LP156WH4 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 15.6 inches diagonally measured active display area with HD
resolution (1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue subpixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors. The LP156WH4 has been designed to apply the interface method that enables low power, high
speed, low EMI. The LP156WH4 is intended to support applications where thin thickness, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the subpixels, the LP156WH4 characteristics provide an excellent flat display for office automation products such
as Notebook PC.
1
EEPROM Block
for EDID
User connector
40
1366
TFT-LCD Panel
LVDS
1port
Timing Control
Block
DVCC
Pin
VCC
(HD, GIP, TN)

768
CLKs
Power
Block
AVCC, AVDD
VGH, VGL, GMA
Source Driver
(Bottom Bent)
GIP CLKs, DSC
VLED
LED_EN
PWM
LED Driver
Block
VOUT_LED
FB1~4
Control & Data
LED Backlight Assy
Power
EDID signal & Power
General Features
Active Screen Size
15.6 inches diagonal
Outline Dimension
359.3(H, typ) 209.5(V, typ) 5.5(D,max) [mm]
Pixel Pitch
0.252mm 0.252 mm
Pixel Format
1366 horiz. By 768 vert. Pixels RGB strip arrangement
Color Depth
6-bit, 262,144 colors
Luminance, White
220 cd/m2(Typ.5 point @ PWM Duty = 100%)
Power Consumption
Total 4.3 W(Typ.) Logic : 0.7W (Typ.@ Mosaic), B/L : 3.6W (Typ.@ VLED 12V )
Weight
420g (Max.)
Display Operating Mode
Transmissive mode, normally white
Surface Treatment
Glare treatment of the front polarizer
RoHS Comply
Yes
BFR / PVC / As Free
Yes for all
Ver. 1.0
Feb. 28, 2012
4 / 32
www.panelook.com
LP156WH4
2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
Table 1. ABSOLUTE MAXIMUM RATINGS

Values
Parameter
Symbol
Min
Max
Units
Notes
Power Input Voltage
VCC
-0.3
4.0
Vdc
at 25 r 5qC
Operating Temperature
TOP
50
qC
Storage Temperature
HST
-20
60
qC
Operating Ambient Humidity
HOP
10
90
%RH
Storage Humidity
HST
10
90
%RH
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39qC Max, and no condensation of water.
90% 80%
60%
60
50
40%
40
30
20
20%
10
Humidity[(%)RH]
Wet Bulb
Temperature []
Storage
Operation
0
10%
-20
10
20
30
40
50
60
70
80
Dry Bulb Temperature []
Ver. 1.0
Feb. 28, 2012
5 / 32
www.panelook.com
LP156WH4
3. Electrical Specifications
3-1. Electrical Characteristics
The LP156WH4 requires two power inputs. The first logic is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second backlight is the input about LED BL.with LED Driver.
Table 2. ELECTRICAL CHARACTERISTICS
Values
Parameter
Symbol
Unit
Notes
3.6
220
255
mA
0.7
0.8
ICC_P
1500
mA
ZLVDS
90
100
110
LED Power Input Voltage
VLED
7.0
12.0
21.0
LED Power Input Current
ILED
300
325
mA
LED Power Consumption
PLED
3.6
3.9
LED Power Inrush Current
ILED_P
1500
mA
100
0.2
PWM Impedance
ZPWM
20
40
60
PWM Frequency
FPWM
150
1000
Hz
PWM High Level Voltage
VPWM_H
2.2
5.3
PWM Low Level Voltage
VPWM_L
0.3
ZPWM
20
40
60
LED_EN High Voltage
VLED_EN_H
2.2
5.3
LED_EN Low Voltage
VLED_EN_L
0.3
12,000
Hrs
Min
Typ
Max
VCC
3.0
3.3
ICC
Power Consumption
PCC
Power Supply Inrush Current

LVDS Impedance
LOGIC :
Power Supply Input Voltage
Power Supply Input Current
Mosaic
BACKLIGHT : ( with LED Driver)
PWM Duty Ratio

PWM Jitter
LED_EN Impedance
Life Time
Ver. 1.0
Feb. 28, 2012
10
11
6 / 32
www.panelook.com
LP156WH4
Note)
1. The measuring position is the connector of LCM and the test conditions are under 25, fv = 60Hz,
Black pattern.
2. The specified Icc current and power consumption are under
the Vcc = 3.3V , 25, fv = 60Hz condition and Mosaic pattern.
3. This Spec. is the max load condition for the cable impedance designing.
The below figures are the measuring Vcc condition and the Vcc control block LGD used.
The Vcc condition is same as the minimum of T1 at Power on sequence.
Rising time
Vcc
0V
3.3V
90%
10%
0.5ms
4. This impedance value is needed for proper display and measured form LVDS Tx to the mating connector.
5. The measuring position is the connector of LCM and the test conditions are under 25.
6. The current and power consumption with LED Driver are under the Vled = 12.0V , 25, Dimming of
Max luminance and White pattern with the normal frame frequency operated(60Hz).
7. The below figures are the measuring Vled condition
12.0V
and the Vled control block LGD used.
Rising time 90%
VLED control block is same with Vcc control block.
VLED
0V
10%
0.5ms
8. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
9. If Jitter of PWM is bigger than maximum, it may induce flickering.
10. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent
to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for
more consistent brightness control at any specific level desired.
11. The life time is determined as the time at which brightness of LCD is 50% compare to that of minimum
value specified in table 7. under general user conditionU
Ver. 1.0
Feb. 28, 2012
7 / 32
www.panelook.com
LP156WH4
3-2. Interface Connections

This LCD employs two interface connections, a 40 pin connector used for the module electronics interface and
the other connector used for the integral backlight system.
Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)
Pin
Symbol
NC
VCC
VCC
V EEDID
Description
No Connection.
LCD Logic and driver power (3.3V Typ.)
LCD Logic and driver power (3.3V Typ.)
DDC Power (3.3V)
NC
Clk EEDID
DDC Clock
DATA EEDID
DDC Data
ORX0-
Negative LVDS differential data input
ORX0+
Positive LVDS differential data input
10
GND
11
ORX1-
12
ORX1+
13
GND
14
ORX2-
15
ORX2+
16
GND
17
ORXC-
18
ORXC+
19
GND
20
NC
No Connection.
LCM Ground
LCM Ground
[Interface Chip]
1. LCD :
SiW, SW0645(LCD Controller)
Including LVDS Receiver.
2. System : SiW LVDSRx or equivalent
* Pin to Pin compatible with LVDS
[Connector]
LSMtron GT05Q-40S-H10-MN
[Mating Connector]
20453-040T-0# series or equivalent
[Connector pin arrangement]

X
[W
LCM Ground
Negative LVDS differential clock input
Positive LVDS differential clock input
LCM Ground
[LCD Module Rear View]
No Connection
21
NC
22
GND
23
NC
No Connection
24
NC
No Connection
25
GND
26
NC
No Connection
27
NC
No Connection
28
GND
29
NC
30
31
NC
GND
No Connection
LCM Ground (LED Backlight Ground)
32
GND
33
GND
No Connection
LCM Ground
LCM Ground
LCM Ground
No Connection
34
NC
35
PWM
36
LED_EN
37
38
NC
VLED
LED Backlight On/Off

No Connection
LED Backlight Power (7V-21V)
39
VLED
40
VLED
Ver. 1.0
Notes
No Connection.
System PWM Signal input for dimming
Feb. 28, 2012
8 / 32
www.panelook.com
LP156WH4
3-3. LVDS Signal Timing Specifications
3-3-1. DC Specification
LVDS |VID|
LVDS +
VIN_MAX VIN_MIN
VCM
# |VID| = |(LVDS+) (LVDS-)|
# VCM = {(LVDS+) + (LVDS-)}/2
0V
Symb
ol
Min
Max
Unit
Notes
LVDS Differential Voltage
|VID|
100
600
mV
LVDS Common mode Voltage
VCM
0.6
1.8
LVDS Input Voltage Range
VIN
0.3
2.1
Description
3-3-2. AC Specification
Tclk
LVDS Clock
LVDS Data
tSKEW
Description
tSKEW (Fclk = 1/Tclk)

1) 85MHz > Fclk 65MHz : -400 ~ +400
2) 65MHz > Fclk 25MHz : -600 ~ +600
Symbol
Min
Max
Unit
Notes
tSKEW
- 400
+ 400
ps
85MHz > Fclk

65MHz
tSKEW
- 600
+ 600
ps
65MHz > Fclk

25MHz
tSKEW_EO
- 1/7
+ 1/7
Tclk
Maximum deviation
of input clock frequency during SSC
FDEV
Maximum modulation frequency

of input clock during SSC
FMOD
200
KHz
LVDS Clock to Data Skew Margin
LVDS Clock to Clock Skew Margin (Even

to Odd)
Ver. 1.0
Feb. 28, 2012
9 / 32
www.panelook.com
LP156WH4
tSKEW_EO
LVDS Odd Clock

Tclk
LVDS Even Clock
Tclk
LVDS Even Data
< Clock skew margin between channel >

Freq.
Fmax
m QGmkl}
Fcenter
Fmin
X
mtvk
Time
< Spread Spectrum >
3-3-3. Data Format

1) LVDS 1 Port
RCLK+
RA+/-
R3
R2
R1
R0
G0
R5
R4
R3
R2
R1
R0
G0
R5
R4
RB+/-
G4
G3
G2
G1
B1
B0
G5
G4
G3
G2
G1
B1
B0
G5
RC+/-
B5
B4
B3
B2
DE
B5
B4
B3
B2
DE
RD+/-
G7
G6
R7
R6
G7
G6
R7
R6
Previous (N-1)th Cycle
VSYNC HSYNC
B7
B6
Current (Nth ) Cycle
VSYNC HSYNC
B7
B6
Next (N+1)th Cycle
< LVDS Data Format >

Ver. 1.0
Feb. 28, 2012
10 / 32
www.panelook.com
LP156WH4
3-4. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation.
Table 4. TIMING TABLE
ITEM
Symbol
Min
Typ
Max
Unit
fCLK
70.0
MHz
Period
tHP
1464
1492
1528
Width
tWH
32
48
62
Width-Active
tWHA
1366
1366
1366
Period
tVP
776
782
792
Width
tWV
Width-Active
tWVA
768
768
768
Horizontal back porch
tHBP
34
42
60
Horizontal front porch
tHFP
32
36
40
Vertical back porch
tVBP
12
Vertical front porch
tVFP
DCLK
Frequency
Hsync
Vsync
Data
Enable
Note
tCLK
tHP
tCLK
tHP
Appendix) all reliabilities are specified for timing specification based on refresh rate of 60Hz.
However, LP156WH4 has a good actual performance even at lower refresh rate (e.g. 40Hz or 50Hz)
for power saving mode, whereas LP156WH4 is secured only for function under lower refresh rate.
60Hz at Normal mode, 50Hz, 40Hz at Power save mode. Dont care Flicker level (power save mode).
3-5. Signal Timing Waveforms
Condition : VCC =3.3V

High: 0.7VCC
Data Enable, Hsync, Vsync
Low: 0.3VCC
tCLK
DCLK
Hsync
0.5 Vcc
tHP
tWH
tHBP
tWHA
tHFP
tWVA
tVFP
Data Enable
tVP
tWV
Vsync
tVBP
Data Enable
Ver. 1.0
Feb. 28, 2012
11 / 32
www.panelook.com
LP156WH4
3-6. Color Input Data Reference

The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.
Table 5. COLOR DATA REFERENCE
Input Color Data
RED
Color
Basic
Color
RED
GREEN
BLUE
Ver. 1.0
GREEN
MSB
BLUE
LSB MSB
R5
R4 R3 R2 R1
Black
Red
Green
Blue
Cyan
Magenta
LSB
G4 G3 G2 G1 G0 B5
B4
0 0
0 0
1 0
0 1
0 0
0 1
1 0
Yellow
White
RED (00)
RED (01)
R0 G5
LSB MSB
B3
B2
B1
B0
0 0
1 0
0 1
1 1
0 1
1 1
1 0
1 1
1 1
0 0
0 0
1 0
0 0
RED (62)
0 0
0 0
RED (63)
1 0
0 0
GREEN (00)
0 0
0 0
GREEN (01)
0 0
1 0
...
GREEN (62)
0 1
0 0
GREEN (63)
0 1
1 0
BLUE (00)
0 0
0 0
BLUE (01)
0 0
0 0
BLUE (62)
0 0
0 1
BLUE (63)
0 0
0 1
Feb. 28, 2012
12 / 32
www.panelook.com
LP156WH4
3-7. Power Sequence

90%
90%
Power Supply Input

VCC
0V 10%
10%
T1
Interface Signal, Vi
LVDS
T2
T4
T3 T7
Valid Data
0V
T5
LED BL
On/Off Control Signal
LED_EN
3.0V
3.0V
T6
0V (Off)
T10
T9
Valid Data
LED BL
Dimming Control Signal
PWM
0V (Low)
T8
T11
90%
LED Driver Input Voltage

VLED
0V
10%
90%
T13
T12
10%
Table 6. POWER SEQUENCE TABLE

Value
Logic
Parameter
Min.
Typ.
Max.
T1
0.5
T2
T3
Value
Units
LED
Parameter
Min.
Typ.
Max.
10
ms
T8
ms
50
ms
T9
ms
ms
T10
ms
T4
150
ms
T11
ms
T5
200
ms
T12
0.5
ms
T6
ms
T13
ms
T7
10
ms
Units
Note)
1. Do not insert the mating cable when system turn on.
2. Valid Data have to meet 3-3. LVDS Signal Timing Specifications
3. LVDS, LED_EN and PWM need to be on pull-down condition on invalid status.
4. LGD recommend the rising sequence of VLED after the Vcc and valid status of LVDS turn on.
Ver. 1.0
Feb. 28, 2012
13 / 32
www.panelook.com
LP156WH4
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable for approximately 30 minutes in
a dark environment at 25qC. The values specified are at an approximate distance 50cm from the LCD surface
at a viewing angle of ) and 4 equal to 0q.
FIG. 1 presents additional information concerning the measurement equipment and method.
FIG. 1 Optical Characteristic Measurement Equipment and Method
Optical Stage(x,y)
LCD Module
Pritchard 880 or
equivalent
50cm
Table 9. OPTICAL CHARACTERISTICS
Table 7. OPTICAL CHARACTERISTICS
Parameter
Symbol
Ta=25qC, Vcc=3.3V, fV=60Hz, fCLK= 70.0MHz

Values
Min
Typ
Max
Units
Contrast Ratio
CR
400
500
Surface Luminance, white
LWH
185
220
cd/m2
G WHITE_5P
80
G WHITE_13P
60
70
TrR+ TrD
16
ms
RX
0.588
0.618
0.648
RY
0.339
0.369
0.399
GX
0.325
0.355
0.385
GY
0.573
0.603
0.633
BX
0.121
0.151
0.181
BY
0.073
0.103
0.133
WX
0.283
0.313
0.343
WY
0.299
0.329
0.359
Luminance Variation
Response Time
Notes
1
2
3
4
Color Coordinates
RED
GREEN
BLUE
WHITE
Viewing Angle
x axis, right()=0q)
4r
40
45
degree
x axis, left ()=180q)
4l
40
45
degree
y axis, up ()=90q)
4u
10
15
degree
y axis, down ()=270q)
4d
30
35
degree
Gray Scale
Ver. 1.0
6
Feb. 28, 2012
14 / 32
www.panelook.com
LP156WH4
Note)
1. Contrast Ratio(CR) is defined mathematically as
Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels
2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 1.
LWH = Average(L1,L2, L5)
3. The variation in surface luminance , The panel total variation (G WHITE) is determined by measuring LN
at each test position 1 through 13 and then defined as followed numerical formula.
For more information see FIG 2.
G WHITE =
Maximum(L1,L2, L13)
Minimum(L1,L2, L13)
4. Response time is the time required for the display to transition from white to black (rise time, Tr R) and
from black to white(Decay Time, TrD). For additional information see FIG 3.
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.
* fV = 60Hz
6. Gray scale specification
Ver. 1.0
Gray Level
Luminance [%] (Typ)
L0
0.16
L7
1.48
L15
5.57
L23
12
L31
20.8
L39
35.3
L47
55.5
L55
79.1
L63
100
Feb. 28, 2012
15 / 32
www.panelook.com
LP156WH4
FIG. 2 Luminance
<Measuring point for Average Luminance & measuring point for Luminance variation>
H
A
10mm
6
8
3
B
V
11
H,V : ACTIVE AREA

A : H/4 mm
B : V/4 mm
10
1
4
10mm
POINTS: 13 POINTS
5 13
12
FIG. 3 Response Time
Active Area
The response time is defined as the following figure and shall be measured by switching the input signal
for black and white.
TrD
TrR
%
100
90
Optical
Response
10
0
white
white
black
FIG. 4 Viewing angle
Normal
Eye
<Dimension of viewing angle range>
I = 180q
,
Left
I = 90q , Up
T
I
I = 0q
I = 270q
Ver. 1.0
,
Right
,
Down
Feb. 28, 2012
16 / 32
www.panelook.com
LP156WH4
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP156WH4. In addition the figures
in the next page are detailed mechanical drawing of the LCD.
Outline Dimension
Horizontal
359.3 r 0.5mm
Vertical
209.5 r 0.5mm
Thickness
5.5mm (max)
Horizontal
350.0 r 0.5mm
Vertical
197.1 r 0.5mm
Horizontal
344.232 mm
Vertical
193.536 mm
Bezel Area
Active Display Area

Weight
Surface Treatment
Ver. 1.0
420g (Max.)
Glare treatment of the front polarizer
Feb. 28, 2012
17 / 32
www.panelook.com
LP156WH4
Note) Unit:[mm], General tolerance: r 0.5mm
<FRONT VIEW>
Ver. 1.0
Feb. 28, 2012
18 / 32
www.panelook.com
LP156WH4
Note) Unit:[mm], General tolerance: r 0.5mm
<REAR VIEW>
Ver. 1.0
Feb. 28, 2012
19 / 32
www.panelook.com
LP156WH4
[ DETAIL DESCRIPTION OF SIDE MOUNTING SCREW ]
* Mounting Screw Length (A)

= 2.0(Min) / 2.5(Max)
* Mounting Screw Hole Depth (B)
= 2.5(Min)
* Mounting hole location : 3.1(Typ)
* Torque : 2.5 kgf.cm(Max) / 2.3kgf.cm(Min)
(Measurement gauge : torque meter)
Notes : 1. Screw plated through the method of non-electrolytic nickel plating is preferred
to reduce possibility that results in vertical and/or horizontal line defect due to
the conductive particles from screw surface.
Ver. 1.0
Feb. 28, 2012
20 / 32
www.panelook.com
LP156WH4
LGD Proposal for system cover design.(Appendix)

1
Gap check for securing the enough gap between LCM

and System cover.
Max Thickness
Sponge
LCM Reflector Side
System Cover
A Boundary Line
1.Rear
side of LCM is sensitive against external stress,and previous check

about interference is highly needed.
Define
2.In case there is something from system cover comes into the boundary
above,mechanical interference may cause the FOS defects.
(Eg: Ripple, White spot..)
Check if antenna cable is sufficiently apart from T-CON of LCD Module.
Define
{Tjvu
{Tjvu
GOOD
NO GOOD
1.If system antenna is overlapped with T-CON,it might be cause the noise.
Ver. 1.0
Feb. 28, 2012
21 / 32
www.panelook.com
LP156WH4
LGD Proposal for system cover design.

3
Gap check for securing the enough gap between LCM

and System hinge.
COF
(D-IC)
Hinge
Side Mount Screw Hole (4ea)
GAP:Min2.0mm
(L TYPE)
(I TYPE)
1.At
Define
least 2.0mm of gap needs to be secured to prevent the shock

related defects.
2.L type of hinge is recommended than I type under shock test.

4
Checking the path of the System wire.
#3
#2
Bad
#1
Ok
Good
1.COF area needs to be handled with care.

Define
Ver. 1.0
2.GOOD Wire path design to system side.

OK Wire path is located between COFs.
BADWire path overlapped with COF area.
Feb. 28, 2012
22 / 32
www.panelook.com
LP156WH4
LGD Proposal for system cover design.

5
Using a bracket on the top of LCM is not recommended.
bracket
Define
1.Condition without bracket is good for mechanical noise,and can minimize

the light leakage from deformation of bracket.
2.The results shows that there is no difference between the condition
with or without bracket.
Securing additional gap on CNT area..
System cover inner side.
A-1
User connector
area.
User connector
Cable pathway.
A~A-1
cut
FPC:Flexible Printed Circuit.
Define
Ver. 1.0
1.CNT area is specially sensitive against external stress,and additional

gap by cutting on system cover will be helpful on removing the Ripple.
2.Using a thinner CNT will be better. (eg: FPC type)
Feb. 28, 2012
23 / 32
www.panelook.com
LP156WH4
6. Reliability
Environment test condition
No.
Test Item
Conditions
High temperature storage test
Ta= 60qC, 240h
Low temperature storage test
Ta= -20qC, 240h
High temperature operation test
Ta= 50qC, 50%RH, 240h
Low temperature operation test
Ta= 0qC, 240h
Vibration test (non-operating)
Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min

3 axis, 1hour/axis
Shock test (non-operating)
Half sine wave, 180G, 2ms

one shock of each six faces(I.e. run 180G 2ms
for all six faces)
Altitude
0 ~ 10,000 feet (3,048m) 24Hr

0 ~ 40,000 feet (12,192m) 24Hr
operating
storage / shipment
{ Result Evaluation Criteria }

There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.
Ver. 1.0
Feb. 28, 2012
24 / 32
www.panelook.com
LP156WH4
7. International Standards
7-1. Safety
a) UL 60950-1, Second Edition, Underwriters Laboratories Inc.
Information Technology Equipment - Safety - Part 1 : General Requirements.
b) CAN/CSA C22.2 No.60950-1-07, Second Edition, Canadian Standards Association.
c) EN 60950-1:2006 + A11:2009, European Committee for Electrotechnical Standardization (CENELEC).
d) IEC 60950-1:2005, Second Edition, The International Electrotechnical Commission (IEC).
7-2. EMC
a) ANSI C63.4 American National Standard for Methods of Measurement of Radio-Noise
Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.
American National Standards Institute (ANSI), 2003.
b) CISPR 22 Information technology equipment Radio disturbance characteristics Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 Sound and television broadcast receivers and associated equipment Radio disturbance
characteristics Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.
7-3. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003
Ver. 1.0
Feb. 28, 2012
25 / 32
www.panelook.com
LP156WH4
8. Packing
8-1. Designation of Lot Mark
a) Lot Mark
A
A,B,C : SIZE(INCH)
E : MONTH
D : YEAR
F ~ M : SERIAL NO.
Note
1. YEAR
Year
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
Mark
Month
Jan
Feb
Mar
Apr
May
Jun
Jul
Aug
Sep
Oct
Nov
Dec
Mark
2. MONTH
b) Location of Lot Mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
8-2. Packing Form

a) Package quantity in one box : 22 pcs
b) Box Size : 468x355x270mm
Ver. 1.0
Feb. 28, 2012
26 / 32
www.panelook.com
LP156WH4
8-3. Label Description

Model Name
Lenovo CODE
LGD CODE
Lot Mark
LGD Code
(1) Model Name : L P 1 5 6 W H 4 -
T L N 1
Revision Code
Product Type
Display Mode
Basic Model Serial No.
Resolution : HD
Size (inch) : 15.6
Application : NBPC
LGD Brand Initial: L
(2) Lot Mark
: 1 5 6 A
7 C 0 0 0 0 0 0 1
SERIAL NO.
MONTH
YEAR
SIZE
Lenovo Code
1)Lenovo P/N : 0A66660
2)FRU P/N : 04W3340
Ver. 1.0
Feb. 28, 2012
27 / 32
www.panelook.com
LP156WH4
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to
t
h
e
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V= 200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
Ver. 1.0
Feb. 28, 2012
28 / 32
www.panelook.com
LP156WH4
9-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And dont touch interface pin directly.
9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.
9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5qC and 35qC at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.
Ver. 1.0
Feb. 28, 2012
29 / 32
www.panelook.com
LP156WH4
Byte
(Hex)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
18
12
EDID structure version # = 1
19
13
EDID revision # = 3
20
14
Video input Definition = Digital signal
21
15
Max H image size (Rounded cm) = 34 cm
22
16
Max V image size (Rounded cm) = 19 cm
23
17
24
18
25
26
19
1A
Display gamma = (gamma*100)-100 = Example:(2.2*100)-100=120 = 2.2 Gamma

Feature Support (no_DPMS, no_Active Off/Very Low Power, RGB color display, Timing BLK
1,no_ GTF)
Red/Green Low Bits (RxRy/GxGy)
Blue/White Low Bits (BxBy/WxWy)
27
1B
Red X
Rx = 0.618
28
1C
Red Y
Ry = 0.369
29
1D
Green X
Gx = 0.355
30
1E
Green Y
Gy = 0.603
31
1F
Blue X
Bx = 0.151
32
20
Blue Y
By = 0.103
33
21
White X
Wx = 0.313
34
22
White Y
Wy = 0.329
35
23
Established timing 1 (00h if not used)
00
00000000
36
24
Established timing 2 (00h if not used)
00
00000000
37
25
Manufacturer's timings (00h if not used)
00
00000000
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
Standard timing ID1 (01h if not used)

01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
00000001
00000001
Established
Panel Color Coordinates
Timings
Standard Timing ID
Ver. 1.0
Value
(Hex)
1/3
Byte
(Dec)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Display
Parameters
Vendor / Product
EDID Version
Header
APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM)

Field Name and Comments
Header
Header
Header
Header
Header
Header
Header
Header
EISA manufacture code ( 3 Character ID )
EISA manufacture code (Compressed ASC)
Panel Supplier Reserved - Product Code
( Hex. LSB first )
LCD Module Serial No - Preferred but Optional ("0"
Week of Manufacture
Year of Manufacture
Feb. 28, 2012
LGD
033Ah
If not used)
If not used)
If not used)
If not used)
00 weeks
2011 years
00
FF
FF
FF
FF
FF
FF
00
30
E4
3A
03
00
00
00
00
00
15
01
03
80
22
13
78
Value
(Bin)
00000000
11111111
11111111
11111111
11111111
11111111
11111111
00000000
00110000
11100100
00111010
00000011
00000000
00000000
00000000
00000000
00000000
00010101
00000001
00000011
10000000
00100010
00010011
01111000
0A
00001010
61
D5
9E
5E
5B
9A
26
1A
50
54
01100001
11010101
10011110
01011110
01011011
10011010
00100110
00011010
01010000
01010100
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
30 / 32
www.panelook.com
LP156WH4

Byte
(Hex)
36
37
56
38
Horizontal Active
(lower 8 bits)
1366 Pixels
57
39
Horizontal Blanking(Thp-HA)
(lower 8 bits)
126 Pixels
58
3A
Horizontal Active / Horizontal Blanking(Thp-HA) (upper 4:4bits)
59
3B
Vertical Avtive
60
3C
Vertical Blanking (Tvp-HA) (DE Blanking typ.for DE only panels)
61
3D
Vertical Active : Vertical Blanking (Tvp-HA)
62
3E
Horizontal Sync. Offset (Thfp)
36 Pixels
63
3F
Horizontal Sync Pulse Width (HSPW)
48 Pixels
64
40
Vertical Sync Offset(Tvfp) : Sync Width (VSPW)
65
41
Horizontal Vertical Sync Offset/Width
66
42
Horizontal Image Size (mm)
344 mm
67
43
Vertical Image Size
194 mm
68
44
Horizontal Image Size / Vertical Image Size
69
45
Horizontal Border = 0 (Zero for Notebook LCD)
70
46
Vertical Border = 0
(Zero for Notebook LCD)
Non-Interlace, Normal display, no stereo, Digital Separate ( Vsync_NEG, Hsync_NEG ), DE only
note : LSB is set to '1' if panel is DE-timing only. H/V can be ignored.
Flag
Flag
Timing Descriptor #1
Byte
(Dec)
54
55
47
72
73
48
49
74
4A
75
4B
76
4C
77
4D
78
4E
79
4F
80
50
81
51
82
52
83
53
84
54
85
55
86
56
87
57
88
58
89
90
91
59
5A
5B
92
5C
93
5D
94
5E
95
5F
96
60
97
61
98
62
99
63
100
64
101
65
102
66
103
67
104
68
105
69
106
6A
107
6B
71
Ver. 1.0
2/3
Value
(Hex)
Value
(Bin)
58
1B
56
7E
50
00
0E
30
24
30
35
00
58
C2
10
00
00
01011000
19
00011001
00
00
Flag
00
Data Type Tag (Descriptor Defined by manufacturer )
00
Flag
00
Descriptor Defined by manufacturer
00
00
00
00
00
00
00
00
00
00
00
00
00
Flag
00
Flag
00
Flag
00
Data Type Tag ( ASCII String )
FE
Flag
00
ASCII String
L
4C
ASCII String
G
47
ASCII String
20
ASCII String
D
44
ASCII String
i
69
ASCII String
s
73
ASCII String
p
70
ASCII String
l
6C
ASCII String
a
61
ASCII String
y
79
Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASC code 0Ah,set remaining char = 20h 0A
Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASC code 0Ah,set remaining char = 20h 20
Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASC code 0Ah,set remaining char = 20h 20
00000000

Pixel Clock/10,000 (LSB)
Pixel Clock/10,000 (MSB)
70 MHz @ 60Hz
768 Lines
14 Lines
(upper 4:4bits)
3 Lines : 5 Lines
(upper 2bits)
(mm)
Feb. 28, 2012
00011011
01010110
01111110
01010000
00000000
00001110
00110000
00100100
00110000
00110101
00000000
01011000
11000010
00010000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
11111110
00000000
01001100
01000111
00100000
01000100
01101001
01110011
01110000
01101100
01100001
01111001
00001010
00100000
00100000
31 / 32
www.panelook.com
LP156WH4
Checksum

Byte
(Dec)
108
109
Byte
(Hex)
6C
6D
Flag
Flag
110
6E
Flag
111
6F
Data Type Tag ( ASCII String )
112
70
Flag
113
71
ASCII String
114
72
ASCII String
115
3/3
Value
(Hex)
Value
(Bin)
00
00
00
FE
00
4C
50
31
35
36
57
48
34
2D
54
4C
4E
31
00000000
00000000
00000000
11111110
00000000
01001100
01010000
73
ASCII String
116
74
ASCII String
117
75
ASCII String
118
76
ASCII String
119
77
ASCII String
120
78
ASCII String
121
79
ASCII String
122
7A
ASCII String
123
7B
ASCII String
124
7C
ASCII String
125
7D
ASCII String
126
7E
Extension flag (# of optional 128 panel ID extension block to follow, Typ = 0)
00
00000000
127
7F
Check Sum (The 1-byte sum of all 128 bytes in this panel ID block shall = 0)
83
10000011
Ver. 1.0
Feb. 28, 2012
00110001
00110101
00110110
01010111
01001000
00110100
00101101
01010100
01001100
01001110
00110001
32 / 32

Panel LG Display Lp156wh4-Tln1 2

Uploaded by

Copyright:

Available Formats

Panel LG Display Lp156wh4-Tln1 2

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Panel LG Display Lp156wh4-Tln1 2

Uploaded by

Copyright:

Available Formats

www.panelook.

Global LCD Panel Exchange Center

15.6 HD TFT LCD

LG Display Co., Ltd.

*When you obtain standard approval,

Products Engineering Dept.

Please return 1 copy for your confirmation with

Feb. 28, 2012

Global LCD Panel Exchange Center

ABSOLUTE MAXIMUM RATINGS

LVDS SIGNAL TIMING SPECIFICATION

SIGNAL TIMING SPECIFICATIONS

SIGNAL TIMING WAVEFORMS

COLOR INPUT DATA REFERNECE

APPENDIX. LPL PROPOSAL FOR SYSTEM COVER DESIGN

DESIGNATION OF LOT MARK

APPENDIX. Enhanced Extended Display Identification Data

Feb. 28, 2012

Global LCD Panel Exchange Center

Jul. 21, 2011

Aus. 31. 2011

Oct. 12. 2011

Jan. 05. 2012

Update Color coordinates

Update LCM Drawing

Update Label drawing

Feb. 28, 2012

First Draft (Preliminary Specification)

Update Gray scale

Feb. 28, 2012

Global LCD Panel Exchange Center

(HD, GIP, TN)

GIP CLKs, DSC

Control & Data

LED Backlight Assy

EDID signal & Power

15.6 inches diagonal

359.3(H, typ) 209.5(V, typ) 5.5(D,max) [mm]

1366 horiz. By 768 vert. Pixels RGB strip arrangement

6-bit, 262,144 colors

220 cd/m2(Typ.5 point @ PWM Duty = 100%)

Display Operating Mode

Transmissive mode, normally white

Glare treatment of the front polarizer

BFR / PVC / As Free

Yes for all

Feb. 28, 2012

Global LCD Panel Exchange Center

2. Absolute Maximum Ratings

Table 1. ABSOLUTE MAXIMUM RATINGS

Power Input Voltage

Operating Ambient Humidity

Dry Bulb Temperature []

Feb. 28, 2012

Global LCD Panel Exchange Center

LED Power Input Voltage

LED Power Input Current

LED Power Consumption