SECTION : 9T1

REMOTE KEYLESS ENTRY AND ANTITHEFT

SYSTEM
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.

TABLE OF CONTENTS
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 9T11
Fastener Tightening Specifications . . . . . . . . . . 9T11
SCHEMATIC AND ROUTING DIAGRAMS . . . . 9T12
Notchback Remote Keyless Entry and AntiTheft
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T12
Hatchback Remote Keyless Entry and AntiTheft
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T13
Control Module/Receiver Connector . . . . . . . . . 9T14
MAINTENANCE AND REPAIR . . . . . . . . . . . . . . 9T15
ONVEHICLE SERVICE . . . . . . . . . . . . . . . . . . . . 9T15
Control Module/Receiver . . . . . . . . . . . . . . . . . . . 9T15
Siren (General Only) . . . . . . . . . . . . . . . . . . . . . . 9T15

Remote Keyless Entry Transmitter

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T17
GENERAL DESCRIPTION AND SYSTEM
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T18
Remote Keyless Entry and AntiTheft System 9T18
Remote Locking and Unlocking . . . . . . . . . . . . .
Security Indicator . . . . . . . . . . . . . . . . . . . . . . . . .
Intrusion Sensing . . . . . . . . . . . . . . . . . . . . . . . . .
Siren (General Only) . . . . . . . . . . . . . . . . . . . . . .

9T18
9T18
9T18
9T18

Vehicle Locator . . . . . . . . . . . . . . . . . . . . . . . . . . .
Autolocking (Safety Lock) . . . . . . . . . . . . . . . . . .
Control Module/Receiver . . . . . . . . . . . . . . . . . . .
Fault or Alarm Indication . . . . . . . . . . . . . . . . . . .

9T18
9T19
9T19
9T19

SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Siren Braket Mounting Bolts.

NSm

LbFt

LbIn

71

9T1 2IREMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM

SCHEMATIC AND ROUTING DIAGRAMS

NOTCHBACK REMOTE KEYLESS ENTRY AND
ANTITHEFT SYSTEM

DAEWOO V121 BL4

REMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM 9T1 3

HATCHBACK REMOTE KEYLESS ENTRY AND

ANTITHEFT SYSTEM

DAEWOO V121 BL4

9T1 4IREMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM

CONTROL MODULE/RECEIVER CONNECTOR

Terminal

Color

Description

YEL

Siren

BLK

Ground

LT BLU

Door and Trunk Tamper Switch

PNK/BLK

Trunk Open Switch

PNK/DKBLU

Hood Open Switch

PPL

Door contact Switch

LT BLU/BLK

Unlock

10

LT GRN/WHT

Lock

11

YEL

Unlock

12

LT GRN

AntiTheft Door Locking Switch

13

DK BLU

Right Turn Signal Bulb

14

15

PNK

Ignition+

16

17

LT GRN

Diagnostic Communication

18

LT GRN/RED

Key Reminder Switch

19

YEL/DK GRN

Security Indicator

20

PPL

AntiTheft Door Locking Switch

21

22

23

24

BRN

Trunk Open Switch

25

ORN

Battery+

26

LT BLU

Left Turn Signal Bulb

DAEWOO V121 BL4

REMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM 9T1 5

MAINTENANCE AND REPAIR

ONVEHICLE SERVICE
CONTROL MODULE/RECEIVER
Removal Procedure
1.
2.
3.
4.

Disconnect the negative battery cable.

Remove the floor console. Refer to Section 9G,
Interior Trim.
Disconnect the control module/receiver electrical
connector.
Slide the control module/receiver away from its
mounting bracket.

Installation Procedure
1.
2.
3.
4.

Install the control module/receiver on its mounting

bracket.
Connect the control module/receiver electrical connector.
Install the floor console. Refer to Section 9G, Interior Trim.
Connect the negative battery cable.

SIREN (GENERAL ONLY)

Removal Procedure
1.
2.

DAEWOO V121 BL4

Remove the siren electrical connector.

Remove the siren bracket mounting bolts and siren.

9T1 6IREMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM

Installation Procedure
1.

Install the siren with the mounting bolts.

Tighten
2.

Tighten the siren braket mounting bolts to 8 NSm

(71 lbin).
Connect the siren electrical connector.

DAEWOO V121 BL4

REMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM 9T1 7

REMOTE KEYLESS ENTRY

TRANSMITTER PROGRAMMING
The Remote Keyless Entry System allows for the use of
as many as four(4) transmitters for each vehicle. Replacement Remote Keyless Entry System Transmitters must
first be programmend to specific vehicle using the
Scan100 Secan tool.
This process is completed using serial data communication between the Scan 100 Scan tool and the Remote Keyless Entry Control Unit and is the only method available for
programming Transmitters.
Notice : All Transmitters for a specific vehicle must be programmed at same time.
Notice : Once the programming function of the Remote
Keyless Entry System is activated, any Transmitter(existing or new) that is not programmed(or reprogrammed)
during the programming procedure will no longer operate
the Remote Keyless Entry System of that vehicle.
Notice : Ensure that the doors, hood and trunk/rear hatch
are closed prior to starting the programming procedure.
1. Connect the Scan 100 Scan Tool to the Data Link
Connector(DLC)
2. Turn the Scan 100 Scan Tool ON by pressing the
Power Button, then wait for the MAIN MENU
screen to be displayed.
3. From the MAIN MENU screen, select Diagnostics
by pressing #1 on the Key Pad.
4. From the MODEL YEAR screen, select the appropriate model year of the specific vehicle by either scrolling down to the year and pressing ENTER, or by pressing the respective item number on
the Key Pad.
5. From the VEHICLE TYPE screen, select the specific vehicle model by either scrolling down to the
model name and pressing ENTER, or by pressing
the respective item number on the Key Pad.
6. From the SYSTEM SELECTION MENU screen,
select Body by pressing #2 on the Key Pad.
7. From the BODY SELECTION MENU screen, select
Coding by pressing #2 on the Key Pad.

DAEWOO V121 BL4

8.

From the CODY SELECTION MENU screen, select

Coding by pressing #1 on the Key Pad.
9. From the SECRET NUMBER OF CODINGS
screen, enter for(4) zeros (0000) in the for(4)
boxes labeled 1234.
10. From the CODING SYSTEM SELECT screen, select Keyless Entry by pressing #2 on the Key Pad.
Notice : A slight delay may occur and PLEASE WAIT
may be displayed before the next screen appears.
11. From the KEYLESS ENTRY CODING SYSTEM
screen, select Coding Transmitter by pressing #1
on the Key Pad.
12. When directed by the Scan 100 Scan Tool, press
any Button on the first Transmitter to be programmed.
CAUTION : Ensure that Transmitters from other vehicles in the immediate area are not activated during
this procedure.
13. Continue programming Transmitters when directed
by the Scan 100 Scan Tool until all Transmitters
have been programmed.
Notice : A maximum of four(4) Transmitters may be programmed to a vehicle.
14. Once all Transmitters have been programmed,
press the ESC Button on the Key Pad. The display will confirm the number of Transmitters programmed. If the number displayed does not match
the number of Transmitters programmed, repeat
the procedure.
15. Turn the Scan 100 Scan Tool OFF by pressing the
POWER Button, then disconnect it from the Data
Link Connector.
16. Wait approximately 10 seconds, then test the operation of each programmed Transmitter to ensure
it operates properly.
The control module/receiver leaves the programming
mode automatically and switches to the normal operating
mode when either of the following conditions occurs:
S
the scan tool is disconnected from the ALDL.
S
Four passwords are recorded in the control module/
receiver.

9T1 8IREMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM

GENERAL DESCRIPTION
AND SYSTEM OPERATION

SECURITY INDICATOR

REMOTE KEYLESS ENTRY AND

ANTITHEFT SYSTEM

There is a security indicator on the instrument panel. After

the LOCK button of the transmitter is pressed, the module
is placed in the armed mode, and the security indicator
flashes. The security indicator turns ON for 0.1 second
and OFF for 0.7 second. It then flashes at that frequency
until the control module/receiver is disarmed.

The remote keyless entry and antitheft system can perform the following functions:

INTRUSION SENSING

S
S
S
S
S

Remotely lock and unlock the vehicle doors by

means of a handheld, highfrequency transmitter.
Sense intrusion into the vehicle.
Activate a warning in the event of an intrusion.
Help the driver find the vehicle in a parking area.
Automatically relock the doors if the door or the
trunk is not opened within 30 seconds after the vehicle has been unlocked by the remote keyless
entry.
Communicate serial data to a scan tool to help
diagnose system faults.

The remote keyless entry and antitheft system consists

of the following components:
S
S
S
S
S
S
S
S
S
S

Keyless entry and antitheft control module/receiver.

Security indicator.
Trunk open switch (NOTCHBACK).
Trunk tamper switch (NOTCHBACK).
Front door tamper switches.
Door contact switches.
Central door lock relay.
Turn signal bulbs.
Siren.
Hood open switch.

REMOTE LOCKING AND UNLOCKING

The handheld transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/receiver in the vehicle. The effective range of the transmitter
varies between 5 and 10 meters, (approximately 16 to 32
feet), depending on whether or not objects, such as other
vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK button which only function when the ignition is OFF. Pressing
the UNLOCK button has the following effects:
S
S
S

The doors are unlocked.

The turn signal bulbs flash twice.
The control module is disarmed.

Pressing the LOCK button has the following effects:

S
S
S

The doors are locked.

The turn signal bulbs flash once.
The control module is armed.

The transmitter has a replaceable battery. The battery is

designed to last at least two years before replacement is
necessary.

The antitheft function is armed if the transmitter sends

the LOCK message to the control module/receiver when
the ignition is OFF. When the hood, door, or trunk is
opened, the hood open, door contact, or trunk open switch
sends a ground signal to the control module/receiver.
Unless the control module/receiver is disarmed, the siren
will be activated when the ground signal is received from
the trunk open, hood open, or door contact switches.
The following actions disarm the antitheft system:
S
S

An UNLOCK message is received from the transmitter.

Key operation is detected by the tamper switches.
(The tamper switches are operated by the lock cylinders in the front doors and trunk.)

The alarm will also be activated if the control module/receiver detects voltage from the ignition before either of the
following conditions occur:
S
S

An UNLOCK message is received from the transmitter.

Key operation is indicated by the tamper switches.

SIREN (GENERAL ONLY)

The remote keyless entry system is armed when the
LOCK message is received from the transmitter when the
ignition is OFF. When the system is armed, it will activate
the siren and flash the turn signals for 28 seconds if any
of the following conditions occur:
S
S
S
S
S

Close all the windows.

Turn the ignition key to LOCK and remove the key.
Have all passengers get out of the vehicle.
Close all doors, the hood and the turnk lid.
The control module/receiver detects ignition voltage
while the system is armed.

The siren will not operate if any of the following conditions

occur after the system has been armed:
S
S
S

The door is opened with the key.

The trunk is opened with the key.
The UNLOCK or LOCK button on the remote transmitter is pressed within 2 seconds after the siren is
activated.

VEHICLE LOCATOR
The remote keyless entry system assists the driver in locating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate the
location of the vehicle. The duration of the flashes and the
DAEWOO V121 BL4

REMOTE KEYLESS ENTRY AND ANTITHEFT SYSTEM 9T1 9

length of time between flashes is used to indicate certain
vehicle conditions. Refer to Fault or Alarm Indication in
this section.

AUTOLOCKING (SAFETY LOCK)

The remote keyless entry system features an autolocking
feature. If the doors are unlocked with the remote transmitter when the control module/receiver is in the armed
mode, the doors are automatically relocked after 30 seconds unless any of the following events occur:
S
S
S
S

A door is opened.
The ignition is ON.
The trunk is opened.
The hood is opened.

CONTROL MODULE/RECEIVER
The remote keyless entry control module/receiver is contained in the floor console. The module/receiver processes signals from the remote transmitter and various
switches. It activates the alarm if an intrusion is detected.
The control module/receiver also has a selfdiagnostic
function which will display trouble codes. In order to display trouble codes, a scan tool must be connected to the
data link connector (DLC).
The control module/receiver will not communicate with
transmitters from other vehicles because there are over
four billion possible electronic password combinations. It

DAEWOO V121 BL4

is highly unlikely that any transmitters will use the same

password. The control module/receiver has an attached
antenna to detect signals from the transmitter.

FAULT OR ALARM INDICATION

When the UNLOCK button on the remote transmitter is
pressed, the control module/receiver will flash the parking
lights to indicate information about the remote keyless
entry and antitheft system.
Normal Condition: If there has not been an intrusion, and
no fault has been detected, the control module/receiver
will signal a normal condition when the UNLOCK button is
pressed. The parking lights will flash twice for 0.5 second,
with a 0.5 second pause between flashes.
Fault Indication: If there is a fault in the remote keyless
entry and antitheft system, the control module/receiver
will signal the fault when the UNLOCK button is pressed.
The parking lights will flash twice for 1 second, with a 0.5
second pause between flashes.
Alarm Indication: If there has been an intrusion since the
last time the LOCK button was pressed, the control module/receiver will signal that there has been an intrusion
when the UNLOCK button is pressed. The parking lights
will flash twice for 0.5 second, with a 1.5 second pause between flashes.
Alarm and fault information will be erased the next time the
transmitter arms the control module/receiver by transmitting a LOCK message.