Uso de Analizador de Video Sencore TVA92 - 2

Complete Flyback/IHVT Testing
Some customers have expressed concern

that they have found defective flybacks
that pass the Sencore ringer test. This is
because flybacks can fail in several
different ways. The purpose of this Tech
Tip is to show how a flyback fails and give
a procedure to properly test a IHVT or
flyback for all of its failure modes.
When checking out a flyback, dont
overlook the obvious. An ohmmeter
should still be used to make quick checks
to find open windings and dead shorts.
However, when the ohmmeter shows no
failure, use the followling test methods to
dynamically check the flyback for all of its
failures.
The Ringer Test

The ringer test is a quick, easy, and
dynamic way to check a flyback for
shorted turns. This is a common IHVT
failure, but not the only failure. The ringer
test switches an impedance matching
capacitor in parallel with the coil under
test to form a tank circuit.
On older Z-Meter models, the ringer test
had to be manually switched to match the
impedance of the coil. On recent models,
the switching is done automatically. The
Z-Meter then sends a pulse to excite the
coil and counts the number of rings. If the

rings are 10 or better, your transformer
has no shorted turns. All windings on the
transformer do not have to ring 10, some
secondary windings will never ring 10.
The primary coil is usually the best place
to ring a flyback. However, if you get 10
rings or better on any winding, your
flyback doesnt have any shorted turns.
See Fig. 1.
A flyback with a shorted turn or turns
becomes very inefficient. This will cause
the amplitude of rings to decrease very
rapidly and the rings will read below 10.
See Fig. 2.
If your readings are marginal (8-12), wind
some solder around the core of the IHVT
and redo the ringer test. A good flyback
will read a low number (0-4), but a bad
flyback will read about the same as the
first ringer test.
The Leakage Test

Another common way that an IHVT can
fail is arcing or shorting from winding-towinding. This is usually caused by
overheating of the flyback which leads to
cracks in the plastic. These cracks can
cause external or internal arcing which
Fig. 3: Example of possible leakage paths

in the IHVT.
will break down a flybacks insulation and

cause windings to short.
This can be tested with a Sencore ZMeter. You first need to find two separate
windings on the IHVT. Then hook up the
leads (one to each winding) and select a
capacitor type (doesnt matter which
type). Enter the highest voltage amount
your Z-Meter will allow and push the
leakage button (00.00 should be
displayed). It may take a couple seconds
to read out. If any leakage is found, the
windings are breaking down and the IHVT
is defective. Fig. 3 shows examples of
possible leakage paths in the IHVT.
This procedure is also effective on yokes.
Leakage from the vertical to the horizontal
yoke can be detected from the yoke plug
using this method. These test procedures
are sometimes referred to as a high-pot
test.
IHVT Drive Test
Fig. 1: Represents a typical oscilloscope

waveform when a good IHVT is being ringer
tested.
Fig. 2: Represents a typical oscilloscope

waveform when a bad IHVT is being ringer
tested.
An IHVT contains multiplier diodes and

capacitors incorporated into the flyback to
make high voltage, this is almost standard
in modern TVs and computer monitors.
The output of an IHVT includes the
second anode voltage, and usually the
focus and screen voltages. These diodes
level and the transformer will produce

high voltage in proportion. Next, measure
the DCV at the anode lead and compare
your results with the chart below.
See Fig. 4 for the proper lead hookups.
Internal shorts in the Focus/Screen divider
network can also develop in an IHVT. To
check for this, measure the focus and
screen voltage while doing the IHVT drive
test. The focus voltage should be slightly
higher than the screen voltage and both
voltages should be a stable DCV. Arcing of
the Focus/Screen spark gaps on the video
board can be another sign of focus/screen
shorts. This board is located on the neck
of the CRT.
Fig. 4: Shows the proper lead hookups for doing an IHVT Drive Test.
and capacitors can fail causing decreased

or no high voltage. The IHVT Drive Test
checks these multiplier diodes and
capacitors. To perform the test, a
generator with a horizontal sync signal is
needed. The CM2125 can be used when
testing a monitor IHVT, and the TVA92 or
VA62 can be used when testing an NTSC

TV IHVT.
To perform the IHVT test, input a 25 VPP
horizontal sync signal to the primary
winding of the transformer. This simulates
the actual horizontal signal at a reduced
In closing, lets recap all of the ways a

flyback/IHVT can fail:
1. Shorted Turns - Check with the Ringer
Test.
2. Arcing from core to winding or winding to
winding - Check with the Leakage Test.
3. Multiplier Failures - Check with the
IHVT Drive Test
Normal CRT High Voltage
Normal
H.O.T.
Collector
PPV
10kV
15kV
20kV
25kV
30kV
35kV
100
200
300
400
500
600
700
800
900
1000
1100
2500
1250
833
625
500
417
357
313
278
250
227
3750
1875
1250
938
750
625
536
469
417
5000
2500
1667
1250
1000
833
714
625
556
500
455
6250
3125
2083
1563
1250
1042
893
781
694
625
568
7500
3750
2500
1875
1500
1250
1071
938
833
750
682
8750
4375
2917
2188
1750
1458
1250
1094
972
875
795
375
341
Chart 1: Expected DCV output with 25 VPP input.
Form # 6841
Printed In U.S.A.

Uso de Analizador de Video Sencore TVA92 - 2

Uploaded by

Copyright:

Available Formats

Uso de Analizador de Video Sencore TVA92 - 2

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Uso de Analizador de Video Sencore TVA92 - 2

Uploaded by

Copyright:

Available Formats

Complete Flyback/IHVT Testing

Some customers have expressed concern

The Ringer Test

coil and counts the number of rings. If the

The Leakage Test

Fig. 3: Example of possible leakage paths

will break down a flybacks insulation and

IHVT Drive Test

Fig. 1: Represents a typical oscilloscope

Fig. 2: Represents a typical oscilloscope

An IHVT contains multiplier diodes and

level and the transformer will produce

and capacitors can fail causing decreased

VA62 can be used when testing an NTSC

In closing, lets recap all of the ways a

Normal CRT High Voltage

Chart 1: Expected DCV output with 25 VPP input.

You might also like