Models MPH Wrench

Solved with COMSOL Multiphysics 5.
Stresses and Strains in a Wrench

Introduction
This tutorial demonstrates how to set up a simple static structural analysis. The analysis
is exemplified on a combination wrench during the application of torque on a bolt.
Despite its simplicity, and the fact that very few engineers would run a structural
analysis before trying to turn a bolt, the example provides an excellent overview of
structural analysis in COMSOL Multiphysics.
Model Definition
The model geometry is shown below.
1 |
STRESSES AND STRAINS IN A WRENCH
Solved with COMSOL Multiphysics 5.2
The bolts fixed constraint is at the cross section shown below. A load is applied at the
box end of the combination wrench.
Applied load
Fixed constraint
Here, assume that there is perfect contact between the wrench and the bolt. A possible
extension is to apply a contact condition between the wrench and the bolt where the
friction and the contact pressure determines the position of the contact surface.
Application Library path: COMSOL_Multiphysics/Structural_Mechanics/

wrench
Modeling Instructions
From the File menu, choose New.
NEW
1 In the New window, click Model Wizard.

MODEL WIZARD
1 In the Model Wizard window, click 3D.

2 In the Select physics tree, select Structural Mechanics>Solid Mechanics (solid).
3 Click Add.
4 Click Study.
5 In the Select study tree, select Preset Studies>Stationary.
6 Click Done.
2 |
GEOMETRY 1
Import 1 (imp1)
1 On the Home toolbar, click Import.
2 In the Settings window for Import, locate the Import section.
3 Click Browse.
4 Browse to the applications Application Library folder and double-click the file
wrench.mphbin.
5 Click the Build All Objects button.

6 Click the Zoom Extents button on the Graphics toolbar.
ADD MATERIAL
1 On the Home toolbar, click Add Material to open the Add Material window.
2 Go to the Add Material window.
3 In the tree, select Built-In>Structural steel.
4 Click Add to Component in the window toolbar.
5 On the Home toolbar, click Add Material to close the Add Material window.
GLOBAL DEFINITIONS
Parameters
1 On the Home toolbar, click Parameters.
2 In the Settings window for Parameters, locate the Parameters section.
3 |
3 In the table, enter the following settings:

Name
Expression
Value
Description
150[N]
150 N
Applied force
SOLID MECHANICS (SOLID)
Fixed Constraint 1
1 On the Physics toolbar, click Boundaries and choose Fixed Constraint.
2 Click the Wireframe Rendering button on the Graphics toolbar.
3 Select Boundary 35 only.
Boundary Load 1
1 On the Physics toolbar, click Boundaries and choose Boundary Load.
2 Select Boundary 111 only.
3 In the Settings window for Boundary Load, locate the Force section.
4 From the Load type list, choose Total force.
5 Specify the Ftot vector as
0
-F
The minus sign means that the force is applied downwards.

MESH 1
Use finer mesh because the geometry contains small edges and faces.
1 In the Model Builder window, under Component 1 (comp1) click Mesh 1.
2 In the Settings window for Mesh, locate the Mesh Settings section.
3 From the Element size list, choose Finer.
4 |
4 Click the Build All button.
The following steps are needed to set up an iterative solver. By using such solver, you
can significantly reduce the memory amount needed for the calculations. If your
computer has at least 6 GB of memory, you can skip these steps and go directly to the
last step and compute the solution.
STUDY 1
Solution 1 (sol1)
1 On the Study toolbar, click Show Default Solver.
2 In the Model Builder window, expand the Solution 1 (sol1) node.
3 In the Model Builder window, expand the Study 1>Solver Configurations>Solution 1
(sol1)>Stationary Solver 1 node.
4 Right-click Study 1>Solver Configurations>Solution 1 (sol1)>Stationary Solver 1 and
choose Iterative.
5 In the Settings window for Iterative, locate the General section.
6 From the Preconditioning list, choose Right.
Stress (solid)
1 Right-click Study 1>Solver Configurations>Solution 1 (sol1)>Stationary Solver
1>Iterative 1 and choose Multigrid.
2 On the Study toolbar, click Compute.
5 |
RESULTS
Stress (solid)
The default plot group shows the von Mises stress in a Surface plot with the
displacement visualized using a Deformation subnode. Change to a more suitable unit
as follows.
1 In the Model Builder window, expand the Stress (solid) node, then click Surface 1.
2 In the Settings window for Surface, locate the Expression section.
3 From the Unit list, choose MPa.
4 On the Stress (solid) toolbar, click Plot.
5 Click the Zoom Extents button on the Graphics toolbar.
3D Plot Group 2
1 On the Home toolbar, click Add Plot Group and choose 3D Plot Group.
2 In the Model Builder window, right-click 3D Plot Group 2 and choose Surface.
3 In the Settings window for Surface, click Replace Expression in the upper-right corner
of the Expression section. From the menu, choose Component 1>Solid

Mechanics>Strain>Principal strains>solid.ep1 - First principal strain.
4 On the 3D Plot Group 2 toolbar, click Plot.
5 Right-click 3D Plot Group 2 and choose Rename.
6 In the Rename 3D Plot Group dialog box, type First Principal Strain in the New
label text field.
6 |
7 Click OK.
Notice that the maximum principal strain is about 0.2%, a result that justifies the
small strain assumption.
7 |
8 |

Models MPH Wrench

Uploaded by

Copyright:

Available Formats

Models MPH Wrench

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Models MPH Wrench

Uploaded by

Copyright:

Available Formats

Solved with COMSOL Multiphysics 5.

Stresses and Strains in a Wrench

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

Application Library path: COMSOL_Multiphysics/Structural_Mechanics/

1 In the New window, click Model Wizard.

1 In the Model Wizard window, click 3D.

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

5 Click the Build All Objects button.

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

3 In the table, enter the following settings:

SOLID MECHANICS (SOLID)

The minus sign means that the force is applied downwards.

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

4 Click the Build All button.

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

of the Expression section. From the menu, choose Component 1>Solid

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

STRESSES AND STRAINS IN A WRENCH

Solved with COMSOL Multiphysics 5.2

STRESSES AND STRAINS IN A WRENCH

You might also like