EE364 Maxwell Simulation Assignment 1

El
Electromagnetics in Power Engineering

Maxwell 3D Simulations of a Residential Wind Generator
Support provided by the Department of Energy (DOE) American Recovery & Reinvestment Act (ARRA) Grant DE -EE0003545
Introduction
In this set of activities, students will gain experience with advanced capabilities of the Ansoft/Ansys
Maxwell 3D software, enabling them to analyze the behavior of an electric generator. Specifically,
students will create a model of the Southwest Windpower Air-X generator (Figure 1, a 400 W system
used to charge batteries in off-grid settings) and will simulate the open-circuit voltage it produces under
specified conditions. The simulation results will then be compared to actual measurements, and
students will select and analyze the effects of changes to the generators design. An understanding of
several electromagnetics concepts will be required for and enhanced by these activities, the most
important concept being magnetic induction. The Motor Application Note in the Ansoft/Ansys Maxwell
v14 Users Guide was used as a reference for these activities, and it along with other sections of the
Users Guide provide examples of additional functions that may be useful to an electric motor /
generator designer. These activities were developed for educational purposes, independently from
Ansoft/Ansys and Southwest Windpower.
It is recommended that these activities be conducted in teams of 2 students. There are three sessions,
with each session expected to take approximately two hours. Each team should submit a report after
the final lab session, in a format and at a time specified by the instructor. The report should contain all
requested data and interpretations, usually emphasized in the procedures by italicized text. Concept and
design questions are asked throughout the procedures and are summarized at the end of each session.
Students should discuss these questions with each other and the instructor during the in-class sessions
but may choose to write their reports outside of class, to ensure that the simulations are completed
during the allotted time.
Figure 1. Southwest Windpower Air-X wind generator (http://windenergy.com)
Session I Modeling the Air-X Rotor and Stator
Session I - Modeling the Air-X Rotor and Stator

Creating a Model of the Rotor
The rotor of the Air-X generator (Figure 2) is connected to the Air-X blade-hub assembly and rotates
along with that assembly when its windy. The rotor has 12 permanent magnets with alternating
magnetic field directions distributed around its perimeter. When the rotor spins, these rotating magnets
will create a changing magnetic field through the stator coils. This changing magnetic field will induce an
EMF (i.e., voltage) across the coils terminals, providing power when a load is connected across the coils.
Figure 2. Rotor of Southwest Windpower Air-X wind generator.

(From http://store.windenergy.com)
Initializing Global Variables

To model the rotor, first start the Maxwell 3D software. (Select OK to any warnings about
WebUpdate.) Set the following global options, ignoring the other options on each tab for now: From the
pull-down menus at the top of the main software window, select Tools->Options->Maxwell3D Options.
Under the General Options tab, check Duplicate boundaries/mesh operations with geometry and then
select OK. Next, select Tools->Options->Modeler Options. Under the Operation tab, select
Automatically cover closed polylines. Under the Display tab, make sure that Highlight selection
dynamically is not checked. On the Drawing tab, select Edit property of new primitives, and then
select OK. Finally, set the default units to mm via the Tools->Options->General Options->Default Units
tab (you may have to scroll upward in the Length pull-down list to find mm).
From the main pull-down menus, select Project->Insert Maxwell 3D Design. A default outline for this
design type will appear in the Project Manager window, in the upper-left corner of the main software
window. The first item in this window, the Projects name, will be changed when you save the file (File>Save As). To change the second item in the list, the Designs name, you may right-click on the default
name and use the Rename option. Select Maxwell 3D->Solution Type and check the Transient option
(in the Magnetic category) to complete the initial setup. Next youll create a model of the Air-X rotor.
2
Importing and Editing User Defined Primitives of the Rotor

Fortunately, Maxwell contains a library of common rotor and stator models. These models were created
in a companion program called RMXprt and can be imported directly into Maxwell. So, instead of
starting from scratch, you can use one of these existing models and change a few parameters to get a
reasonably close fit to your system. Select Draw->User Defined Primitive->Syslib->RMxprt and notice
the range of existing models. Most models with the word core in the name could be used to create
either a rotor or a stator, depending on the parameter values.
Select a rotor (i.e., core) type that looks interesting, and review the descriptions of the default
parameters that pop up. You may need to expand the pop-up window and change the column sizes to
see the entire description of each parameter, as shown in Figure 3. Select OK to create the object using
the default parameters, save a screen shot of the resulting graphic image (Edit->Copy Image in Maxwell
and then CNTL-V in Microsoft Word), record the name of the rotor type, and then delete the rotor object
(Edit->Delete or the Delete key) after youve captured its image. If you have trouble deleting the object,
try selecting its graphic or its name in the list to the left of the graphing area (known as the Model
Tree), such that the graphic is highlighted in pink, and then try to delete it again.
Figure 3. Parameters for the SquirrelCage model, an example User Defined Primitive in Ansoft/Ansys Maxwell.
3
Save screenshots of the graphical representations of three different core types, and describe a few
technical differences between the cores you selected. The differences you discuss should be something
that engineering and physics students would have enough knowledge and training to understand, but
the general public may not. For example, a comment that Core X was bigger than Core Y (assuming no
additional, more advanced discussion) would not receive many points.
Tips & Tricks: Changing the view of your model
Try the different pan & zoom modes that have toolbar shortcuts located near the topright corner of the main Maxwell window, starting with the hand icon .
If you get stuck in one of the pan or zoom modes, press the ESC key.
Holding the shift key and the left mouse button while moving the mouse is a handy
shortcut for panning the view.
As a shortcut for zooming in and out, left-click on the location you want to zoom, then
rotate the mouse track ball forward or backward.
If youre having a difficult time rotating an object in the direction you want, try
zooming out first. The following represent example ways to then rotate your object:
o To rotate the object so that it can be viewed from the top or bottom, try
selecting the Rotate around current axis icon, then left-clicking in the lowercenter area of the graphing window and moving the mouse up or down while
holding down the mouse button.
Alternatively, selecting the Alt key and then double-clicking in the

upper-center of the graphing window will change the view so youre
looking down on the object, while Alt-double-clicking in the lowercenter of the window will help you view the object from below.
o To rotate the object around the Z-axis, select the Rotate around current axis
icon, click in the left-center of the graphing window, and move the mouse
right or left.
o To rotate the x-y plane, select the Rotate around current axis icon, click in
the right-center of the graphing window, and move the mouse up and down.
To return to the default view, select the Alt key and double-click in the upper-right
corner of the graphing window.
Well use the User Defined Primitive called PMCore (Permanent Magnet Core) to model the Air-X
rotor. One instance of this primitive will be used to model the non-PM components of the rotor, and a
duplicate instance will create the magnets, or vice versa. Go ahead and create the PMCore object with
the default parameters, so that you can see the effect when you change each parameter. After youve
created the object, select the Command tab in the Properties window, located along the middle-left
side of the main software window. (If you dont see this tab, or dont see any values listed in the
Properties window, expand the Model Tree to the left of the graphing area, and select
4
CreateUserDefinedPart under the PMCore1 entry.) Change DiaGap, the diameter of the rotor to the
gap between it and the stator as shown in Figure 4, to 89.2 mm. Change DiaYoke to 0 mm, since we
essentially have a solid rotor, and notice how the graphic changes. The rotors Length (in the Z-direction)
should be 12.8 mm.
As seen in Figure 4, the Air-X generator has 12 permanent magnets around its perimeter. The magnets
are created so that some have their north pole on the curved side, and others have their south pole on
that side. The magnets are then placed around the rotor to produce 12 alternating magnetic poles (or 6
N-S pole-pairs) facing the stator, so that the magnetic field through the stator coils will alternate
periodically as the rotor spins. Therefore, set the PMCore parameter named Poles to 12.
DiaGap
S
N
Length
Figure 4. Example parameters of the Air-X rotor.
The Maxwell software is currently showing you the non-PM portion of the rotor, and if slots have been
cut into the rotor for magnets, you will see them as blank sections within the rotor. However, if the
magnets are to be placed along the rotors perimeter, as in the Air-X case, you cant currently see the
default geometry for the magnets. Change InfoCore (the very last parameter in the Properties window,
Command tab) to 1, so the graphing window will show you the rotors magnets. Now try entering
different values for PoleType (back near the top of the list), to see the various options for the magnets
locations and geometries in this User Defined Primitive. The PoleType option #3 appears to be the best
fit for the Air-X magnets geometry.
Continuing down the PMCores parameter list, the Embrace parameter represents the fraction of the
rotors circumference covered by magnets. Set its value to 0.8, and notice how the graphic of the rotor
changes. Then enter 6.3 mm for ThickMag, the magnets maximum thickness. The parameter WidthMag
is used only for PoleTypes 4 and 5; in our case, the magnets width is determined internally by the
Embrace parameter, so the value entered here doesnt matter. Enter a value of 20 mm for Offset, and
note the effect. If you drew a vector that represented the magnets radius of curvature, the offset would
represent the difference between the rotors origin and this vectors origin, as shown in Figure 5.
5
Magnet
surface
radius
Stator
inner
radius
Offset
Figure 5. Visual representation of the PMCore Offset parameter (from the RMXprt Users Guide).
The PMCores Bridge and Rib parameters do not apply to our PoleType, so leave the default values.
(Note that although the User Defined Primitives are very handy and descriptions of their parameters
might be found in the RMXprt software or its documentation, new users can expect to have some
difficulties understanding at least some of each objects parameters. So, when you are modeling a
different electric motor / generator for another project at work or school, you may well need to follow
the process demonstrated above, patiently selecting different models and exploring their parameter
options until you find something that fits your projects needs.)
Now youll check whether the parameters entered above fit with a few actual measurements of the AirX rotor. Zoom in to view two magnets from the +Z direction, as shown in Figure 6. (For example, try Altdouble click at the top center of the graphing window to look at the magnets from above, and then use
the
icon to zoom into a selected area.) Then select Modeler->Measure->Position, as you need to
measure the distance between two points on the graph. Click on the inner corner of one magnet, and
then move the mouse (without clicking) to the corner of the adjacent magnet, as shown in Figure 6a.
Note that the mouse icon changes to a square when it is at an objects corner. The icon changes to a
triangle when the mouse is at the center of an objects edge. The meanings of other shapes can be seen
by right-clicking on the graphing window and then selecting Snap Mode. Record your measured distance
between the two magnets, and press the ESC keep to exit the measurement mode. The actual
measurement for the gap between the magnets on the Air-X rotor is approximately 1 mm. Alter the
rotor models Embrace parameter slightly until the gap measurement on your model is a better fit to the
actual measurement. (If you dont see the relevant parameters in the Properties window, select the
CreateUserDefinedPart item in the Model Tree, to the left of the graphing area, under Solids>vacuum->PMCore1.) Record your final Embrace value and the associated measurement on your model.
Next, measure the edge thickness of a magnet, as shown in Figure 6b, and update the Offset value until
this measurement is approximately equal to the measured value of 5.0 mm. Record your final Offset
value and the associated measurement of the model magnets edge thickness. Remember to save your
model occasionally.
(a)
(b)
Figure 6. Measuring (a) the distance between two magnets on the Air-X rotor and (b) the magnets edge thickness.
Select the Attribute tab in the Properties window (if you dont see this tab, select the PMCore1 entry
from the Model Tree, under the Solids category), and change the name of this object from PMCore1
to Magnets by clicking on the PMCore1 value next to Name. You may also want to change the objects
graphed color or transparency; those parameters are located at the bottom of the Attribute tab.
Now type CNTL-C to copy your version of this User Defined Primitive, and then type CNTL-V to paste a
second instance of it, since you still need to create the non-magnetic section of the rotor. The new
object should appear under the Solids list in the Model Tree. Rename the new object from
Magnets1 to Rotor and select the + sign next to the Rotor listing in the Model Tree. If you then
select CreateUserDefinedPart under the Rotor listing, the dimensions and other parameters that
you recently specified for the magnets will be displayed in the Properties window. Similarly, you could
double-click on CreateUserDefinedPart to get a pop-up window containing these parameters. Change
InfoCore (the last property in the list) back to 0 to show the non-magnetic section of the rotor, and your
entire graphic should now look similar to Figure 7 when viewed from the +Z axis. (To get the same view
as Figure 7, Alt-double-click in the top-center section of the graphing window, and then select the Fit all
the contents in the view toolbar icon.)
Dont worry if it looks like the rotor core intersects with the magnets; the software program graphically
represents smooth curves as segments to save time, but it resolves the objects at a finer level during
processing. You can select View->Curved Object Visualization, Absolute Deviation, Apply to see this
more detailed resolution.
Before proceeding, you may want to double-check your rotors (and similarly, your magnets) parameter
entries with those shown in Figure 8.
Figure 7. Ansoft/Ansys Maxwell 3D model of the Air-X rotor.
Defining Materials
Select Rotor from the Solids list again, and the Attribute tab should be shown in the Properties
window. Select the entry that currently shows vacuum, and select Edit from the pull-down menu.
(You can also access the materials pull-down menu from the toolbar, where you see vacuum.) Either
search by name or scroll through the materials until you find stainless steel, which the Air-X rotor
appears to be made of. Select stainless steel (steel_stainless) and then OK. If you no longer see the
rotor in the graphic window, double-click on your projects name in the Project Manager window.
The Air-X generator uses nickel-plated neodymium magnets, specifically NdFeB 40H magnets, where 40
implies a maximum magnetic energy product, BHmax, of 40 MGOe and H indicates a maximum
operating temperature of 120 C. (More information about these advanced magnets can be found on a
variety of internet sites, including http://www.kjmagnetics.com.) In Maxwell, assign the material
NdFe35 to the Air-X magnets as a good approximation, noting that you can create new material listings
in Maxwell if needed for advanced projects. Youll specify the north/south direction of the magnets
later, in the next session. Save your model. Save a screen capture of your complete rotor model for your
report.
Figure 8. Maxwell 3D parameters for the Air-X rotor. (Some parameters shown in the list do not apply to PoleType.)
Additional Rotor Concept and Design Questions
The Air-X wind generator is often used in off-grid applications. Given this constraint, why
might permanent magnets be a better design choice for creating the rotors magnetic field,
rather than electromagnets? What is an application where electromagnets might be the
better choice? Explain.
Describe one benefit and one drawback of using neodymium magnets in this design, rather
than another type of permanent magnet.
In what country are most of the rare earth magnets, such as those used by the Air-X, made?
Find and briefly summarize a recent article that discusses issues with using rare earth
magnets in electric generators, which may or may not relate to the magnets country of
origin.
As shown in Figure 4, a band wraps around the magnets. The band is screwed into the rotor
on the far side. What do you think is the purpose of this band?
What is the effect of attaching the magnets to a stainless steel rotor core? How is stainless
steel different from, say, copper in terms of its behavior around magnets?
Creating a Model of the Stator

Next youll create a model for the stator (i.e., the stationary part) of the Air-X generator. As shown in
Figures 9 and 10, the stator contains the coils across which EMF will be induced when the rotor spins.
There are three sets of coils representing the three phases. The coils associated with one phase are
located on the outer edge of the stator, the second phase is shifted over by one slot and is coiled at a
slightly smaller radius, and the third phase is in the next set of slots and is closest to the rotor.
Figure 9. Side view of the Air-X stator, with the lower steel laminations pulled apart for educational purposes.
Figure 10. Overhead view of a section of the Air-X stator.

10
Importing and Editing User Defined Primitives for the Stator Core and Coils
Creating the Core
To help you focus on the stator, first select View->Active View Visibility from the main pull-down menu.
Uncheck the Visibility box for the Magnets and Rotor objects, and then select Done. The rotor
objects should no longer be visible in the graphing area, but dont worry, they havent been deleted.
Next, import (by using Draw) the User Defined Primitive called SlotCore. Go ahead and create the
object with the default parameters so that you can analyze the effects of changing each parameter.
After creating the object, select the Command tab in the Properties window to access the following
parameters. Set DiaGap, the diameter of the side facing the rotor, to 91.3 mm. Set DiaYoke,
representing the outer diameter of the stator, to 133.8 mm, and observe the effect of making DiaYoke
greater than DiaGap, which essentially informs Maxwell that youre modeling a stator rather than a
rotor. Set the Length to 12.8 mm, the same value that was used for the rotor. The Air-X stator is not
skewed, but change the Skew to 45, as you will come across skewed slots in practice. Change the view
to better see the skewed stator slots, for example by Alt-double-clicking in the upper-right corner of the
graphing window, and then clicking in the graphing area to de-select the stator. Save a screenshot of the
skewed stator slots, and conduct an internet search to find one application of a skewed core.
Select the CreateUserDefinedPart item under SlotCore1 in the Model Tree to access the stators
parameters via the Properties window again, and change the Skew back to 0. Set the number of Slots
to 36. Zoom in to a few slots on the graphing window, and see the effects of changing the SlotType
parameter (values 1-7). For the Air-X model, well use SlotType #4, which will provide a close although
approximate representation. Save a screenshot of an interesting SlotType other than #4, and then reset
the value to 4 before proceeding.
The next several parameters represent details of the stator slots geometry. The description for each
parameter was found in the pop-up window when the object was first created and can be accessed
again by double-clicking on the appropriate CreateUserDefinedPart item in the Model Tree. The
associated diagram shown in Figure 11 was found in the RMXprt Users Guide. As you enter the
following values, you may want to try larger or smaller numbers on occasion to magnify the effect and
further clarify what the parameter represents. Your final stator slot should look similar to the real Air-X
slot (with coils removed) shown in Figure 12a. The model image shown in Figure 12b used the View>Curved Object Visualization option to more accurately show the stators outer edge.
Hs0, Slot opening height = 0.8 mm

Hs01, Slot closed bridge height = 0 mm
Hs1, Slot wedge height = 0.8 mm
Hs2, Slot body height = 10.5 mm
Bs0, Slot opening width = 2.5 mm
Bs1, Slot wedge maximum width = 5.9 mm
Bs2, Slot body bottom width, 0 for parallel teeth = 0
11
Rs, Slot body bottom fillet = 2 mm

FilletType, 0: a quarter circle; 1: tangent connection; 2&3: Arc Bottom = 0
HalfSlot, 0 for symmetric slot, 1 for half slot = 0
SegAngle, Deviation angle for slot arches (10~30, <10 for true surface) = 5 deg
LenRegion, Region length = 200 mm (default)
InfoCore, 0: core; 100: region = 0
Figure 11. Diagram of the stator slot parameters (from the RMXprt Users Manual)
(a)
(b)
Figure 12. (a) Actual and (b) Simulated slots for the Air-X stator.
In the Properties window, Attribute tab (also accessed by selecting SlotCore1 from the Model Tree,
Solids category), change the objects name to Stator and change the color and transparency if you
wish. Next, edit the material. Most cores are made of a soft magnetic material with a high relative
permeability. (Explain why in your report.) Sort the list of available materials according to the magnitude
of their relative permeability, by selecting the Relative Permeability column label in the material
selection window a couple times. Choose the material with the highest relative permeability, which will
likely be a type of steel. Select the View/Edit Materials button at the bottom of the material selection
window, and then select the BH Curve button on the pop-up window to see a section of this materials
hysteresis curve. Save a screen shot of this curve for your report (Alt-PrntScrn on the keyboard, then
CNTL-V in Microsoft Word), and discuss whether the data indicates that the material has linear or non12
linear magnetic properties, and whether it is a soft or hard magnetic material. Note that you can input
or edit the H-B entries to fit a different magnetic material, when precision is needed.
Select OK to return to the View / Edit Material window. Select the steels Composition Value, and
change it from Solid to Lamination, as the Air-X core is composed of laminated sheets of steel rather
than a solid steel block (see Figure 9). Change the Stacking Factor, defined as the proportion of steel to
insulation in a given direction, to 0.94, and set the Stacking Direction to V(3), the Z-direction. In your
report, explain the rationale for using laminated sheets for the stators core, and explain in terms of
physics phenomena why stacking the sheets in the Z-direction is the best option. Also discuss why
engineers often construct larger cores from a specialized form of steel, labeled M19, even though its
more expensive. (Conduct a simple web search about M19 steel to aid in your interpretation.) Select
OK to finalize the stators material, and save your model.
Creating the Coils

When you look at the list of User Defined Primitives, youll find four coil models: ConCoil (Con =>
concentric), LapCoil, TransCoil (Trans => transformer), and WaveCoil. Find an image of a lap coil and a
wave coil for your report. In the case of the Air-X generator, the ConCoil option appears to be the best
fit. For each phase of the Air-X stator, a person hand-winds a coil around the first pair of appropriate
stator slots, then changes from clockwise to counter-clockwise rotation (or vice-versa) while winding the
next coil for that phase in the next set of designated slots, and so on using one long wire, so that the
EMF produced by each coil in the series will add in-phase while the alternating magnetic poles rotate
past. This stator coil arrangement is often used in car alternators as well.
Select Draw->User Defined Primitive->SysLib->RMxprt->ConCoil, and select OK to create the coil with
the default parameters. You may want to change the viewing angle to see the coils better. Enter the
same parameter values that you used in creating the stator core, until you reach the coil-specific values
(starting with LayerLoc). Then enter the following values, observing how each entry affects the coil:
LayerLoc, (0: whole; 1: middle; 2: top; 3: bottom) = 3

CoilPitch, Coil pitch measured in slots = 3
o The coil will loop through the 3rd slot from the starting slot. The two intermediate slots
will be used for the other two phases.
EndExt, One-side end extended length = 3.6 mm
o The plastic inserted into the slot extends about this far above (and below) the stator
core
LayerExt, Span layer extension in the axial direction = 2
o Multiplication factor for how far the coil extends from the rotor axially
LayerDiff, Span layer difference in the radial direction = 0
AltEnd, 0: same end layers, 1: alternate end layers = 1
InfoCoil, (0: coil; 1: terminal1; 2: terminal2; 100: region) = 0
13
You may wish to check your entries against the coil parameters listed in Figure 13. Select the Attribute
tab (or ConCoil1 from the Model Tree, Solids list), change the objects name to PhaseA_Coil, change
the material to copper, and set the color and transparency values as desired. Do select a unique color
for this coil, as it will help to distinguish the three phases later.
Figure 13. ConCoil parameters used to model an Air-X stator coil.
You will duplicate this example coil to create the starting coils for Phases B and C, and then these coils
will be duplicated to create a series of coils for each phase. If the existing PhaseA_Coil object is not
already selected (i.e., highlighted in pink), click on its name in Model Tree. Type CNTL-C to copy the
object, then CNTL-V to paste a duplicate of it. Rename the duplicate to PhaseC_Coil, and change its
color to something unique in your model. Then select CreateUserDefinedPart under the PhaseC_Coil
entry in the Solids list, to access the objects other parameters. Change the LayerLoc entry to 1 (middle),
14
to wrap this coil next to the Phase A coil. Select the Phase C coil by either clicking on its graphic or
selecting its name in the Solids list. Then select Edit->Arrange->Rotate, and rotate the coil around the Zaxis by 10. (Since the Air-X stator has 36 slots, moving from one slot to the adjacent one represents a
rotation of 360/36 = 10 degrees.) Repeat the process to create the first Phase B coil: Copy and paste a
duplicate of the PhaseC_Coil object; change its name to PhaseB_Coil; assign it a unique color; change its
LayerLoc parameter to 2 (top); and then select the coil and rotate it around the Z-axis by 10. Your stator
model should now look similar to the one shown in Figure 14.
Figure 14. Ansoft/Ansys Maxwell 3D model of the Air-X stator, at the point where each phase has one coil.
Now youll create the rest of the coils in each phase. In the Air-X stator, the second coil in each phase
starts three slots from the beginning of the first coil. (The end slot of the first coil is actually the starting
slot of the second coil that is, one slot will contain wires from two coils in a series, as shown in Figures
9 and 10.) This shift of three slots corresponds to a 30 rotation around the Z-axis. Therefore, you will
create a duplicate of the first coil and rotate it by 30 to create the second coil in each phase, and so on
around the stator. Luckily, there is a shortcut for this operation. Pressing the CNTL key so that you can
select multiple items, select PhaseA_Coil, PhaseB_Coil, and PhaseC_Coil from the Solids list. Then select
Edit->Duplicate->Around Axis and enter the following values: Axis: Z, Angle: 30, and Total number: 12.
Select OK, and the remaining coils in each phase will be created. That function saved some time! As
another time saver, you do not have to create a layer of insulation between the coils and the stator core
in this model the conductivities of the copper and steel are so different that Maxwell automatically
considers their boundary to be a non-conductive path.
Select View->Show All->All Views to see the rotor components as well, and then select the Fit all the
contents in the view icon from the toolbar. The result should look similar to the actual and simulated
Air-X generators shown in Figure 15. Save your model. Save screen captures of a couple different views
of your completed electric generator model for your report.
15
(a)
(b)
Figure 15. (a) Actual and (b) Modeled Air-X generators.
Additional Stator Concept and Design Questions
The Air-X stator coils appear to be made of 16-gauge copper wire, approximately 1.3 mm in
diameter. List one advantage and one disadvantage of using a smaller diameter (larger
gauge) wire in a coil.
Magnet wire, such as the wire used for the Air-X stator coils, is coated with enamel, and the
entire coil assembly of the Air-X stator is covered with an additional, thicker coat of enamel.
Discuss the rationale for these design choices.
As shown in Figure 9, a plastic insert is placed around each slot before the coils are wound.
Why are these inserts needed?
As shown in Figure 10, a plastic insert is placed into each slot opening after all of the coils
have been completed. What is the purpose of this plastic insert?
One end each phases wire is connected to the Air-X circuit board, while the other ends of
the three coils are soldered together. What is the name for this type of three-phase
connection?
Summary of Specific Information Requested for the Lab Report

From the Ansoft/Ansys Maxwell 3D Software:
Screen shots and comparisons of three cores from the list of User Defined Primitives.
Measurement of the gap between two magnets when the rotors Embrace parameter is 0.8, and
the final Embrace value which made the gap approximately 1.0 mm, along with the final gap
measurement.
16
The value of the rotors Offset value which made the magnets edge thickness approximately 5.0
mm, and the models measurement of that thickness.
Screen shot of your rotor model.
Screen shot of a SlotCore SlotType other than #3.
Screen shot and example application of skewed slots (or skewed coils).
Screen shot of your selected ferromagnetic materials hysteresis curve. Discuss whether the
data indicates that the material has linear or non-linear magnetic properties, and whether it is a
soft or hard magnetic material.
Two screen shots showing different views of your combined rotor / stator model.
Additional Concept and Design Questions:
Why might permanent magnets be a better design choice for creating the Air-X rotors magnetic
field, rather than electromagnets? What is an application where electromagnets might be the
better choice? Explain.
Describe one benefit and one drawback of using neodymium magnets in the Air-X design, rather
than another type of permanent magnet.
In what country are most of the rare earth magnets, such as those used by the Air-X, made? Find
and briefly summarize a recent article that discusses issues around using rare earth magnets in
power generation, which may or may not relate to the magnets country of origin.
What do you think is the purpose of the band that wraps around the Air-X magnets?
What is the effect of attaching magnets to a stainless steel rotor core? How is stainless steel
different from, say, copper in terms of its behavior around magnets?
List one advantage and one disadvantage of using a smaller diameter wire in a coil.
Discuss the rationale for coating magnet wire and coils with enamel.
Why are plastic inserts placed around each slot in the stator? Why is a plastic insert placed into
the slots opening?
One end each phases wire is connected to the Air-X circuit board, while the other ends of the
three coils are soldered together. What is the name for this type of three-phase connection?
Most stators are made of a soft magnetic material with a high relative permeability. Explain
why.
In your report, explain the rationale for using laminated sheets for the stators core, and explain
in terms of physics phenomena why stacking the sheets in the Z-direction is the best option.
Also discuss why engineers often construct larger cores from a specialized form of steel, labeled
M19, even though its more expensive.
Include a picture of a lap coil and a wave coil for reference.
17
Session II Setting the Initial Simulation Parameters

In this session, you will use Maxwells symmetry option to significantly reduce your models size and
therefore its simulation time, but without affecting the final results. You will then establish the settings
needed to conduct an initial simulation of the Air-X generator and will analyze the results. You may want
to save a copy of your current model as a backup before proceeding.
Reducing the Model Size through Symmetry
The Ansoft/Ansys Maxwell 3D program has a powerful option which allows you to conduct simulations
on the smallest symmetric section of a model, and then expand the results to obtain the complete
solution much faster. The Air-X rotor as 12 magnets representing 6 pole-pairs; therefore, the rotors
geometry and magnetic fields repeat every 60 degrees. The coil geometry repeats every 30 degrees, so
the stator will also be symmetric at 60 degrees. Therefore, we can simulate a 60-degree slice of the
generator to determine its output, while reducing the simulation time by a factor of 6. We will also slice
the generator in half, in the XY plane (making upper and lower halves), taking advantage of that
symmetry as well. As a result, 1/12 of the original volume will be simulated.
To begin sectioning the model, select Edit->Select All. Then select Modeler->Boolean->Split and enter
the following parameters: Split plane: XZ (Read that carefully), Keep fragments: Positive side, Split
objects: Split entire selection. The Delete invalid objects entry should be checked. Select OK. Save a
screen shot of the result. Did the result seem to fit with the parameters you set in the Split window? (If
not, the undo button may be handy
Now rotate the section you want to keep into the negative XZ plane, as follows: Assuming all objects are
still highlighted, select Edit->Arrange->Rotate. Rotate around the Z-axis in the negative direction, -60
degrees in our case. Select Modeler->Boolean->Split, with entries Split Plane: XZ, Keep fragments:
Negative side (Read that carefully), and Split objects: Split entire selection. Then rotate the remaining
section, representing 1/6 of the original, around the Z-axis by +60 degrees to get back to the starting
point. Finally, split the model along the XY plane, keeping the +Z side. The result should look similar to
that shown in Figure 16. Save a screen shot of your reduced model.
In the Model Tree, Solids list (in the copper group), select each coil name in turn so that you can see the
coil sections remaining in the reduced model. When put together, the coil sections should create two
complete coils for each phase. Unfortunately, from the Maxwell softwares perspective, there are areas
where these two coils are occupying the same space, so the simulation cannot be conducted with the
existing coil models. However, we can delete one of the two coils in each phase and double the
simulation results to get the proper values, due to symmetry. For example, look at the alignment of the
two Phase A coils with the magnets, and note their symmetry: Assuming that one magnet has its north
pole aligned toward the stator and the adjacent magnet has its south pole facing the stator, when one of
the Phase A coils sees an increasing magnetic field, the adjacent coil will see the same magnitude of
change in the magnetic flux, but in the opposite direction. Assuming that the adjacent coils are wound in
18
Figure 16. Symmetric section of the Air-X model.
opposite directions (i.e., clockwise vs. counter-clockwise), the EMF produced in these two coils will be
equal in magnitude and will add in-phase. Therefore, you should delete coil sections until just one
complete coil from Phase A remains, and you will later compensate for this change in the final analysis
settings. Repeat the process for Phase B, so that only one coil remains. Unfortunately, from Maxwells
perspective, the Phase C coils intersect with the others, so all of the Phase C coils must be deleted
before the computation can proceed. The Phase B coil will still allow you to see the phase shift from
Phase A, however, and Phase C will be identical except for an additional 120-degree phase shift. Your
model should now look similar to Figure 17.
Figure 17. Symmetric section of the Air-X model with intersecting coils removed.
Specifying the Magnets Fields

19
Now that youre down to just two magnets, it will be easier to define the direction of the magnetic field
created by each magnet. To start the process, youll need to separate the magnets into two unique
objects. Select the existing Magnets object from the Solids list (NdFe35 section), and then select
Modeler->Boolean->Separate bodies. The two magnets should now be separate objects. Rename the
Magnets object to Magnet_S and rename the Magnets_Separate1 entry to Magnet_N.
Select the Magnet_N object, and edit its material. With NdFe35 selected in the materials window,
click on the View/Edit Materials button. Since the magnetic field shown in Figure 18 appears to be
somewhat spherical in nature, select Spherical from the Material Coordinate System Type pull-down
menu in the upper-right corner of the View/Edit Material window. Then select OK, respond Yes to the
pop-up window, and select OK on the main materials window. Now select the Magnet_S object and
edit its material. With NdFe35 selected, click on the Clone Material(s) button. Name the material
NdFe35_S, verify that it has a spherical coordinate system, and set the Rho Component parameter to 1, where the negative sign indicates that the field will be directed inward (southward) along radial lines.
Select OK a couple times to finish the process.
(a)
(b)
Figure 18. (a) Overhead and (b) Side views of iron filings indicating the magnetic field produced by an Air-X magnet.
Currently, the magnets materials are associated with the Global coordinate system, as seen by the
Orientation parameter on the Properties window, Attribute tab. This means that the magnets field lines
will be aligned with spherically radial vectors emanating from the origin. Although this does not
perfectly represent the magnets actual fields, well use this setting as a decent and not-too-complicated
initial value and will refine these fields later if needed.
Defining the Region where Electromagnetic Fields will be Calculated

Now you will define the region where the software program should calculate electromagnetic fields. A
large region will result in long computation times, but on the other hand, important information may be
missed if the region is too small. In the case of an electric motor/generator, we care more about the
fields within the structure than around it, so the region does not need to extend much beyond the
device. In addition, we must pay attention to the symmetry of the problem, keeping the analysis region
20
out of areas that, in reality, would contain more sections of the generator. In our case, this means that
the region will be pie-shaped, so some of the Maxwell shortcuts for creating regions (e.g., the 3D box
and cylinder shortcuts shown in the toolbar) cant be used. Instead, a 2D rectangle will be swept around
the Z-axis to create the pie shaped region.
To begin, select Modeler->Grid Plane->XZ, and rotate the view so that you can see the XZ plane from
the negative Y-axis (e.g., Alt-double-click on the middle left side of the graphing window). Then select
Draw->Rectangle, and do not click anything in the graphing window. Instead, notice that entry boxes for
X, Y, and Z have appeared in the very lower-right corner of the Maxwell 3D window, with the default
units listed in the lower-right corner. Since you need to start the rectangle (and the pie-shaped region)
at the origin, enter 0 for the starting X value. Then tab into the entry box for Y, and enter 0. Tab and
enter 0 for the Z location, and then hit the Enter key. Note that if you move the mouse, it may change
the numbers in the <X, Y, Z> entry boxes, so try to just use the keyboard when entering these numbers.
Next, you may enter the stopping location for the plane graphically, by clicking on a point that appears
on the XZ grid to extend slightly beyond the size of the generator, or you could manually enter dX=70,
dY = 0, dZ = 30 mm. Say OK to any pop-up windows. The resulting rectangle (after rotating back to the
default view) is shown in Figure 19.
Make sure that the rectangle is highlighted, and then select Draw->Sweep->Around Axis. Enter the
following parameters: Sweep axis: Z, Angle of sweep: 60 degrees, Number of segments: 8. Select OK.
You should now have a pie-shaped region which defines the volume where Maxwell will analyze the
electromagnetic fields. In the Properties window, Attribute tab, change the name of the object from
Rectangle1 to Region, and select the Display Wireframe checkbox to more easily see the other
objects. The result should look similar to Figure 20. Remember to save your model frequently.
Figure 19. XZ rectangle used to define the computation region.
21
Figure 20. The pie-shaped computation region for the Air-X Maxwell 3D simulation.
Clarifying Edge Symmetries through Master/Slave Boundaries

To utilize Maxwells symmetry options fully, you will need to set the planes where symmetry occurs,
known in this case as the Master and Slave planes. To begin, select Edit->Select->Faces, or press f.
Select the original rectangle that you constructed while creating the region, i.e., select the face of the
region that lies in the XZ plane and faces the negative Y-axis. (Be sure to select the outside face.) Then
select Maxwell 3D->Boundaries->Assign->Master, and in the resulting window, select U Vector->New
Vector. Click the origin of the global coordinate system (i.e., the lower-left corner of the rectangle from
this view) to represent the start of this vector, and click the lower-right corner of the rectangle as the
end of the vector. Select the Reverse Direction checkbox for V-Vector, and then select OK. Expand the
lists in the Project Manager window until you see the entry for the Master1 boundary (you may have to
use the windows scrollbar), and select that boundary. The result should look similar to Figure 21.
Figure 21. Master plane used for symmetry computations by the Maxwell 3D software.
22
Now rotate to the other side of the pie piece and select the outer face of the regions ending rectangle,
which will serve as the symmetric Slave boundary. Select Maxwell 3D->Boundaries->Assign->Slave,
and set the following parameters: Master Boundary: Master1, U Vector: New Vector (start at the origin,
and end at the outer edge of the rectangle, as you did for the Master boundary), V Vector: Unchecked
(not reversed), and Relation: Hs = Hm. The result should look similar to Figure 22. One effect of these
master / slave boundaries pertains to the coils that were broken into separate segments after you cut
the original model into the 60-degree section: Currents that flow out of a coil into one boundary will
flow into the associated coil on the other boundary. Select the Boundaries heading in the Project
Manager window (upper-left area of the main window) to clear the boundary graphics in preparation
for the next section. Also select o to return to the object rather than face selection mode, and return to
the standard viewing angle (e.g., Alt-double-click in the upper-right corner of the graphing window).
Figure 22. Slave plane used for symmetry computations by the Maxwell 3D software.
Defining the Rotors Rotation

Now you will define aspects of the Air Xs rotation. First, you will need to establish which components
will rotate. You will accomplish this by creating another region, this time called a Band, which encloses
the rotating elements. As with the region, you must be mindful of maintaining the underlying objects
symmetry, so in this case the Band will also be pie-shaped. Select Modeler->Grid Plane->XZ (the
software relies on this grid plane when determining which type of rectangle to create, and will give
errors if the numeric entries dont fit within this plane). Then select Draw->Rectangle, or alternatively
click on the 2D rectangle icon on the toolbar, and enter <0, 0, 0> into the <X,Y,Z> entries at the lowerright corner of the main software window, remembering to Tab between the entry boxes and press
Enter when all three values are correct. The ending X value for this rectangle, which is also dX since we
started at the origin, will represent the line separating the rotating and non-rotating components and
should therefore be located in the airgap between the rotor and stator. Since the rotor had an outer
23
radius of 89.2 2 ~ 44.6 mm (= DiaGap, the diameter of the rotor facing the air gap 2) and the stator
had an inner radius of 91.3 2 ~ 45.6 mm (also DiaGap 2), the edge of the rotation region should fall
within these values. Well use a location near the stator, dX = 45.5 mm, for meshing purposes (discussed
later), dY = 0 mm by definition of an XZ plane, and dZ = 30 mm to match the surrounding Region. Enter
these values into the boxes at the lower-right corner of the main Maxwell software window, and press
Enter. Select OK to any pop-up window.
As with the Region, youll sweep this rectangle to create the symmetric pie-piece Band enclosing objects
that will rotate. Assuming that the starting rectangle is highlighted, select Draw->Sweep->Around Axis,
and enter the following values: Axis: Z, Angle of sweep: 60 degrees, Number of segments: 0. In the
Properties window, Attribute tab, change the name of this object to Band, and select the Display
Wireframe checkbox. Rotate so that youre looking at the system from above, and ensure that your
band encloses the rotor but does not go into the stator, keeping in mind that Maxwell is displaying the
Bands curve as segments for now. The result should look similar to that shown in Figure 23. Save a
screenshot of your view of the Band object for your report. Save your model.
Figure 23. Band region used by Maxwell 3D to identify objects that will rotate.
Ensure that the Band object is still highlighted, and select Maxwell 3D->Model->Motion Setup>Assign Band. (If you dont see the Model option in the pull-down menu, select Maxwell 3D->Solution
Type and ensure that Magnetic->Transient is selected.) In the Type tab, enter the appropriate settings to
have the rotor rotate around the Z-axis: Motion Type: Rotation, Rotation Axis: Global:Z, and Positive,
but dont press OK yet. In the Mechanical tab, set the Angular Velocity to 1000 rpm and then press OK.
(If you make a mistake and need to change your motion setup, you can access this information through
the Project Manager window, by expanding lists until you find Model->MotionSetup1.) Note that range
of operable rotation rates for the Air-X is approximately 300-1700 rpm. Save your model.
24
Setting Coil-Specific Simulation Parameters

In order for Maxwell 3D to calculate some of the information we need for this application, such as the
EMF produced across the Air-X coils, a few additional simulation parameters will be needed. For
example, as described in more detail below, you will need to create Winding excitations and associate
them with the Phase A and Phase C coils. Even though the Air-X coils dont have an excitation (other
than the changing magnetic field), this entity within the software is where important information such
as the number of turns per coil are identified. To create an excitation, you must first create another
entity called a terminal, which essentially defines a cross-section of the coil as the reference point for
calculating induced voltage and current. This procedure will be defined next.
The terminal needs to be offset (i.e., internal to) the simulations bounding region, so an offset
coordinate system needs to be created. Select Modeler->Coordinate System->Create->Relative CS>Offset. Using the entry boxes at the bottom-right of the software window, enter <X,Y,Z> = <0,0,10>
mm. Then, using the CNTL key, select both PhaseA_Coil and PhaseB_Coil from the Solids list in the
Model Tree. Then select Modeler->Surface->Section, set the Section Plane to XY and press OK. This will
create the cross-section terminal through which Maxwell can calculate the induced EMF and current.
However, two terminals were created, while Maxwell will just need one. So, open the Sheets list to the
left of the graphing window, and select the Phase A Section that was just created. Select Modeler>Boolean->Separate Bodies to separate the two sheets / terminals. Keep the section that is closest to
the XZ plane (select each Phase A section in the Sheets list to see where its located), rename it as
PhaseA_Terminal, and delete the other section. Repeat the process for the Phase B coil: Separate the
two sheets, rename the section thats closest to the XZ plane, and delete the other section. The
remaining terminals should look similar to those highlighted in Figure 24.
Before proceeding, change the coordinate system back to the Global one, for example by opening the
Coordinate Systems list in the Model Tree and selecting Global. This will help to clarify subsequent
visualizations.
Figure 24. Highlighted terminals for each coil in the Air-X simulation.
25
The next step in the process is to create a winding entity for each coil and to associate that winding
with the proper terminal. Select Maxwell 3D->Excitations->Add Winding, and set the following
parameters: Name: PhaseA_Winding, Type: Current, Stranded, Current: 0 Amps. Select OK, and then
select the PhaseA_Terminal entity in the Model Tree. In the Project Manager window at the upperleft section of the main window, expand the list until you see the PhaseA_Winding under Excitations.
Right click on it and select Assign Coil Terminal. (If you get an error message, select PhaseA_Winding
in the Model Tree again.) Change the Number of Conductors to 8, as each Air-X coil contains 8 loops of
wire, but dont press OK yet. Select Swap Direction to define the default current direction at this
terminal to be in the positive Z-axis direction, as shown by the vector in the graphing window and in
Figure 25. Note that this option could be used to clarify a coils winding direction. Select OK. Repeat the
process for Phase B: Create a new winding (PhaseB_Winding), associate the new PhaseB_Winding
with the PhaseB_Terminal, and assign 8 conductors to the winding.
Figure 25. Direction of Phase-A terminal, seen after associating a winding entity with the terminal.
Setting up Miscellaneous Simulation Parameters

Select Maxwell 3D->Design Settings. In the Symmetry Multiplier tab, set the symmetry multiplier to 24
and select OK. This is due to the fact that we cut the model into a 1/6 pie-piece around the Z-axis, then
divided that piece by half in the XY plane, and then removed one of the two coils used in each phase.
You now need to set the time step at which the software will create a new set of calculations. You want
at least several samples for each cycle of the AC signal generated by the Air-X, to clarify the shape of the
waveform, yet you dont want the simulation to take forever. Given 12 magnets, or 6 pole-pairs, 6 cycles
of EMF will be induced with each rotation of the rotor. At 1000 rpm, this corresponds to 6000 cycles per
minute, or 100 cycles per second. So, 100 samples per second (i.e., a time step of 0.01 s) would give one
sample per cycle, a time step of 0.001 s would give 10 samples per cycle, etc. For now, we will use a step
of 0.001 sec = 1 ms, and well stop the simulation at 20 ms to capture two cycles. To implement this,
select Maxwell 3D->Analysis Setup->Add Solution Setup. In the General tab, enter Stop time: 20 ms
26
(use the units pull-down menu to select ms) and Time step: 1 ms, but dont press OK yet. In the Save
Fields tab, select the following: Type: Linear Step, Start: 0 ms, Stop: 20 ms, Step Size: 1 ms. Then select
Add to List so that you can see the fields at each step of the simulation. Select OK, and save your
model.
Select Maxwell 3D->Validation Check to make sure there arent any errors with your simulation. One
expected warning will be associated with Boundaries and Excitations, and a more detailed explanation
will be listed in the Message Manager box in the lower-left corner of the main software window, but
this warning is not a problem. Notify your instructor if you have any other errors.
Running the Simulation!

At last, select Maxwell 3D->Analyze All. You can check the status of the simulation in the Progress
window, in the lower-right area of the main software window. The time step will update as the
simulation proceeds. One nice capability of the Maxwell software is the ability to start analyzing results
as soon as one time step is complete. So, you can begin the next subsection as soon as the output file
associated with the first time step is saved. When the simulation is completely finished (about 10
minutes for this configuration), you should see a Normal completion of simulation on server notice in
the Message window. If your simulation is taking much longer than other peoples, or you think that
somethings wrong, check with the instructor. To stop the simulation, click the right-directed arrow in
the Progress window, and select Abort for an immediate stop, or Clean Stop to finish at the end of the
current time step. The Clean Stop option will save the data acquired so far.
Obtaining Initial Simulation Results

Now youll view the generators magnetic fields. First, select a time step at which you want to view the
fields, by selecting View->Set Solution Context, which is at the very bottom of the View pull-down
menu. Select a non-zero time step and press OK. Hold the CNTL key while selecting (using the Model
Tree) the objects on which you want to see the magnetic fields, such as the rotor, stator, and magnets.
Then select Maxwell 3D->Fields->Fields->B->Mag_B, check the option Plot on the surface only, and
select Done. Save a screen capture of this visualization. For fun, select Maxwell 3D->Fields->Animate
and press OK to see an animation of the magnetic fields as the rotor spins. Remember that the software
is using the symmetry you specified, so even though you see your North and South facing magnets
rotating away from the coils, the software knows that other pairs of N-S poles continue around the
rotor, and you can see the magnetic fields induced on the stator by those invisible magnets.
In the Project Manager window, expand the lists until you see the Field Overlays->B visualization that
you just created. Select the B item and press the Delete key so that you can see the next visualization
more clearly. Select the rotor, stator, and magnets again, and then select Maxwell 3D->Fields->Fields>B->B_Vector to see a vector representation of the magnetic field. As before, select Plot on the surface
only to obtain a clearer visualization. To change the characteristics of the vectors, right click on the
27
graphs scale (the B[Tesla] colorbar) and select Modify. Select the Marker/Arrow tab, and try changing
some of the parameters (e.g., the Arrow options->Size) to improve the visualization. Options on some of
the other tabs may help as well. Save a screen shot of your best vector visualization, and interpret the
image. For example, where are the fields strongest, and does that make sense; do the vector directions
meet your expectations, given the magnets specified directions, etc. You may want to animate the
vectors as well, to see how the magnetic fields through the coils change in time.
To clarify the next visualization, select Modeler->Grid Plane->XY and then delete the Field Overlays->B
item in the Project Manager window again. Select View->Active View Visibility, uncheck everything
except the magnets, and press Done. Using the CNTL key, select both Magnet_N and Magnet_S in
the Model Tree (or select both objects in the graphing window), and then select Maxwell 3D->Fields>Plot Mesh and press Done to see the underlying elements used in Maxwells numerical analysis
routines. Alt-double-click in the upper-right area of the graphing window to return to the default view,
and save a screen capture of the magnets mesh at this stage.
Return to View->Active View Visibility and select the stator, rotor, and coils along with the magnets.
Press Done. Using the CNTL key, select all of these objects in either the graphing window or the Model
Tree list. Select Maxwell 3D->Fields->Plot Mesh and then Done to see the mesh on the other objects as
well. Save screenshots of a couple different views of the underlying mesh. In the Project Manager
window, delete the MeshPlots entry. Return to View->Active View Visibility and uncheck everything
except the Stator object. Select Maxwell 3D->Fields->Plot Mesh one last time, and rotate around the
stator until you can see the meshing on the rotors teeth, as shown in Figure 26. Save a screenshot of
your view of the stator mesh. In your report, interpret the meshes; for example, explain in terms of the
underlying electromagnetics why the mesh needs to be finer in some areas.
Figure 26. The stator mesh created by Maxwell 3D in the Transient solution mode.
28
To see the voltage induced in the coils as the rotor spins, select Maxwell 3D->Results->Create Transient
Report->Rectangular plot. Set the following values in the subsequent window: Category: Winding,
Quantity: FluxLinkage(PhaseA_Winding) and (using the CNTL key) InducedVoltage(PhaseA_Winding).
Then select New Report. Save a screen capture of the plot. This plot probably doesnt look like the
sinusoidal AC waveforms that you may have expected, but it is a promising initial result that does show
the mathematical relationship between the magnetic flux through a coil and the EMF induced across
that coil. What is that mathematical relationship? In the next session, you will use advanced techniques
to refine the simulation and obtain a more accurate representation of the EMF induced in the Air-X coils.

Screenshot and discussion of the model after splitting it across the XZ plane.
Screenshot of the final reduced model, 1/12 of the original model.
Screenshot of the Band object. Discussion of the purpose of the Band object.
Screenshot of the visualization showing the magnitude of the generators magnetic fields.
Screenshot and interpretation of the visualization showing the magnetic field vectors.
Screenshots of the underlying numerical meshes used in this simulation. There should be one
screenshot that focuses on the magnets faces, another that focuses on the rotors teeth, and a
couple different views of the mesh across the entire model. Interpret the variations in these
meshes; for example, explain in terms of the underlying electromagnetics why the mesh needs
to be finer in some areas.
Screenshot of the plot showing the magnetic flux through the Phase A coil and the resulting EMF
induced across that coil as a function of time. Description of the mathematical relationship
between the magnetic flux through and the EMF induced across a coil, and a discussion of
whether / how the plot demonstrates that relationship.
29
Session III Refining the Air-X Simulation

Now that you have a decent model of the Air-X generator, you can start altering some of the simulation
settings to obtain more accurate results, at the expense of additional computation time of course. Since
the focus in this case is on the EMF produced in the Air-X stator coils as the rotor spins, we need to pay
close attention to the aspects of the model and simulation settings that affect the magnetic flux passing
through the coils. As seen in the magnetic field plots that you obtained in the last session, the magnetic
flux is much stronger in the rotors teeth (i.e., the steel components) than in the slots, so we will refine
settings that affect this flux.
One important consideration involves mimicking the devices material properties and shapes as closely
as possible, which we did in the previous sessions since the computation time was still reasonable. As an
example, a stator core with different permeability could make a huge difference in the magnetic flux. In
addition, you may have noticed that the Air-X manufacturers took special care to smooth sharp edges in
the magnets and stator slots (see Figures 12 and 18). Why do you think this is important? These rounded
edges were reproduced in the previous sessions whenever possible, and it would be difficult to alter or
compensate for the remaining sharp edges, so we will try other improvements in this session.
Another important factor is the time step. While viewing the magnetic flux and induced EMF plots in the
last session, you probably knew intuitively that the time step was so large, because the plots were so
choppy. Approaching the problem more analytically, each time step in the last session resulted in a large
rotation the magnet passed one of the stators teeth which each time step, resulting in a huge change
in magnetic flux through that tooth. The time step certainly must be refined to improve the simulation
results.
The underlying mesh represents another important factor in determining the magnetic flux through the
stators teeth, since the magnetic field and other parameters are calculated for each element in the
mesh. The faces of the magnets and stator teeth facing the airgap between the rotor and stator are
especially important, since the fields are changing rapidly there. The meshes you recorded in the
previous session were quite good for a first pass but can be improved.
Finally, the magnetic fields produced by the magnets were not identical to the fields we specified in the
last session. Although difficult to achieve, some improvements will also be attempted to improve this
factor.
In the next few sections, you will be guided through making some of the improvements listed above and
analyzing the effects. You will then experiment with a desig change of your own choice. You may want
to save a backup copy of your current simulation before you start.
30
Reducing the Time Step

Reducing the time step is probably the easiest and most significant refinement to the settings used in
the last session. Expand the list in the Project Manager window until you see the Analysis->Setup1 item.
Select and delete Setup1, and then select Maxwell 3D->Analysis Setup->Add Solution Setup. Set the
Stop time to 10 ms and the Time step to 0.5 ms in the General tab. Well ignore the Save Fields option
for now to reduce the simulation time. Select OK, save your model, and then select Maxwell 3D>Analyze All to run the simulation. (Note that you could have accessed and altered the existing time
parameters by double-clicking on Analysis->Setup1 in the Project Manager window, but the software
doesnt appear to know that the solution needs to be recalculated when those variables are changed. If
you change something else, such as one of the objects parameters, Maxwell will receive the trigger to
conduct a new simulation and will then use your altered time setup.)
You may select Maxwell 3D->Results->Create Transient Report->Rectangular Plot to see the results as
Maxwell processes them. Recall that on the pop-up window, you will select Winding as the Category
and then use the CNTL button while clicking each item that you want to analyze from the Quantity list.
This time, select both the Phase A and Phase B FluxLinkage and InducedVoltage parameters, and
then select New Report and Close. In the resulting plot, Phase A should lead Phase B by 120 degrees, as
expected for this 3-phase design. Note that you may click and drag the Curve Info box to see the
traces better. You may want to work on your report while the simulation runs (~15 minutes). When the
simulation finishes, use Edit->Copy Image to copy the plot, then CNTL-V to paste the plot into your
report. Discuss the differences between the plot you obtained in the previous session with a time step of
1.0 ms, the plot you obtained in this session, and the plots shown in Figure 27, representing time steps of
0.2 and 0.1 ms. Note that the simulation using a time step of 0.2 ms took approximately 30 minutes,
while the 0.1 ms simulation took ~50 minutes. For the remainder of this lab, therefore, you may keep
the 0.5 ms time step as a good compromise between accuracy and computation time.
Refining the Underlying Numerical Meshes

Many numerical analysis techniques, including those used by the Ansoft/Ansys Maxwell 3D software,
divide an object into several discrete pieces and solve each variable associated with that piece (e.g., the
magnetic field strength and direction) at each time step. The smaller these pieces are, the better the
simulation results will be, as the object then appears to be more continuous than discrete. However,
smaller pieces also cause longer simulation times, so as always, people try to find a balance between
realistic results and faster simulation times.
Other solution types within Maxwell that dont include motion, such as the Magnetostatic solution type,
have an adaptive meshing routine that automatically refines an objects mesh until a specified level of
accuracy is achieved in the results. In addition, this meshing routine and the underlying numerical
approach allow for a finer mesh in areas where variables are changing quickly and a courser mesh in
other areas, to maximize efficiency while obtaining accurate results. Unfortunately yet understandably,
the Transient option being used in this analysis, which allows for motion, does not automatically refine
31
XY Plot 1
Maxwell3DDesign1
7.50
0.010
5.00
0.005
2.50
0.000
-0.005
Y Axis
FluxLinkage(PhaseA_Winding)
Setup1 : Transient
Y1
FluxLinkage(PhaseB_Winding)
Setup1 : Transient
Y1
InducedVoltage(PhaseA_Winding)
Setup1 : Transient
Y2
InducedVoltage(PhaseB_Winding)
Setup1 : Transient
Y2
0.00
Y2 [V]
Curve Info
Y1 [Wb]
ANSOFT
0.015
-2.50
-0.010
-5.00
-0.015
-7.50
0.00
2.00
4.00
6.00
8.00
10.00
Time [ms]
(a)
Maxwell3DDesign1
0.010
5.00
0.005
Y1 [Wb]
ANSOFT
7.50
Curve Info
0.000
Y Axis
Setup1 : Transient
Y1
Setup1 : Transient
Y1
Setup1 : Transient
Y2
Setup1 : Transient
Y2
2.50
0.00
-0.005
-2.50
-0.010
-5.00
-0.015
Y2 [V]
XY Plot 1
0.015
-7.50
0.00
2.00
4.00
6.00
8.00
10.00
Time [ms]
(b)
Figure 27. The calculated magnetic flux through and induced EMF across a Phase A and Phase B coil
when the time step is (a) 0.2 and (b) 0.1 ms.
the mesh (it uses the mesh found after one pass) as the iterative refinements after each motion step
would take far too much time.
There are ways that you could alter the mesh of different objects within the Transient solution method.
Under the Maxwell 3D->Mesh Operations pull-down menu, for example, you could specify the
maximum number of elements for an object or the maximum size of an element within an object. In
general, though, its difficult through these approaches to get the fine resolution needed in areas where
the fields are changing quickly without simultaneously obtaining an unreasonably large number of
elements in the rest of the object. Therefore, were going to use a trick where we will switch the
32
solution type to Magnetostatic create a refined mesh, and then input that mesh into the Transient
design.
To begin, save a version of your model under a new name. Then select Maxwell 3D->Solution Type,
change the setting to Magnetostatic, and select OK. If you no longer see the graphical display of your
model, double-click on your projects name in the Project Manager window. Youll soon run the
Magnetostatic simulation to create the refined mesh, plus check the magnetic fields created by your
magnets. First, select Maxwell 3D->Analysis Setup->Add Solution Setup to specify a few required
simulation parameters. In the General tab, set the Maximum Number of Passes to 5 and the Percent
Error to 5. Many analysts would consider this to be a small number of passes and a large error, but these
options will demonstrate the benefits of adaptive meshing without taking an unreasonable amount of
lab time. Select OK, and then select Maxwell 3D->Analyze All to run the simulation.
When the simulation is completed (~10 minutes, depending on the computer), you should obtain
screenshots of meshes to compare with those obtained in the previous session, which essentially
represented one adaptive pass. To begin, go to View->Active View Visibility, uncheck everything except
the magnets, and select Done. Rotate and zoom to see the curved side of the magnets well. Holding the
CNTL button, select both magnets from the graphing window or the Model Tree list, so that they are
highlighted in pink. Then select Maxwell 3D->Fields->Plot Mesh, press Done, and the magnets mesh
under these new conditions should be displayed. Save a screenshot of this mesh. Make the rotor, stator,
magnets, and coils visible; select those objects in the Model Tree; and plot their meshes as well. Save a
couple screenshots showing different views of these meshes, and then delete the MeshPlots item
under the Field Overlays list in the Project Manager window. Make only the stator visible, and plot its
mesh. Rotate and zoom so that you can clearly see the teeth of the stator which face the magnets,
and save a screen shot of the stators mesh before deleting its MeshPlots item. In your report,
compare these meshes to those obtained in the previous session. Select View->Show All->All Views to
show the entire model again, then Alt-double-click in the upper-right corner of the graphing window,
and select the Fit all the contents in the view to return to the default view. Save this model.
In the Project Manager window, select the name of the current design; it should have Magnetostatic
in the name. Then type CNTL-C to copy the design, and click on the - icon to collapse / hide the list of its
components. Select the overall Project name, and type CNTL-V to paste a copy of the design. Doubleclick on the name of the copied design, and expand the list of its components. Then select Maxwell 3D>Solution Type and check the Transient option to allow motion again. Select Maxwell 3D->Analysis
Setup->Add Solution Setup. In the General tab, change the Stop time back to 10 ms, and the Time step
to 0.5 ms. In the Advanced tab, select Import Mesh, to import the refined mesh that you just created in
the Magnetostatic version. Select the Use This Project checkbox in the pop-up window, and make sure
that the name of your Magnetostatic design is listed in the Source Design pull-down. Select OK twice
to accept this setup.
Unfortunately, a few other settings were deleted when the design was edited in the Magnetostatic
mode, so youll need to recreate the current excitations and the motion setup. Select Maxwell 3D>Excitations->Add Winding. Set the name to PhaseA_Winding, click on the Stranded option, and select
33
OK. Expand the list in the Project Manager window until you see the PhaseA_Winding entry under
Excitations. Then expand the Model Tree until you can select the PhaseA_Terminal item under Sheets.
Go back and right click on PhaseA_Winding in the Project Manager window, select Assign Coil
Terminal, set the Number of Conductors to 8, select Swap Direction, and click on OK. Create the
PhaseB_Winding excitation with the same parameters, and associate it with the PhaseB_Terminal.
To reset the motion, select the Band object in the Model Tree, under the Solids->vacuum list. Select
Maxwell 3D->Model->Motion Setup->Assign Band. In the Type tab, specify positive rotation about the
Z-axis, enter 1000 rpm in the Mechanical tab, and press OK. Finally, select Maxwell 3D->Model->Set
Symmetry Multiplier, select the Symmetry Multiplier tab, enter a value of 24 to account for the various
symmetries, and press OK. Save your model, and run the Transient simulation with the new-andimproved mesh by selecting Maxwell 3D->Analyze All. As before, you may see the results as Maxwell
computes each time step. Select Maxwell 3D->Results->Create Transient Report->Rectangular Plot, and
then select the Winding category and the relevant PhaseA Quantities before creating a New Report.
While this simulation progresses, you can start another instance of the Maxwell 3D program and work
on the next section, which starts on the next page. Once the simulation finishes (approximately 40
minutes), save a screenshot of the magnetic flux and induced EMF plots, and compare it to the data you
obtained in the previous section. The data for the time step of 0.1 ms and the mesh that was refined by 5
adaptive meshes is shown in Figure 28 (compare to Figure 27b). For reference, that simulation took
approximately 1.5 hours to complete. To obtain a more accurate result, the time step would be further
reduced and the underlying mesh would be refined by additional adaptive passes in the Magnetostatic
simulation to reach a lower specified error. Such a precise simulation would clearly take a long time to
complete and should only be done once all other aspects of your model have been precisely defined and
tested.
Maxwell3DDesign2
ANSOFT
7.50
0.010
5.00
0.005
2.50
0.000
0.00
Curve Info
-0.005
-0.010
Y Axis
Setup1 : Transient
Y1
Setup1 : Transient
Y1
Setup1 : Transient
Y2
Setup1 : Transient
Y2
Y2 [V]
Y1 [Wb]
XY Plot 1
0.015
-2.50
-5.00
-0.015
-7.50
0.00
2.00
4.00
6.00
8.00
10.00
Time [ms]
Figure 28. The calculated magnetic flux through and induced EMF across a Phase A and Phase B coil when the
time step was 0.1 ms and the mesh was refined by five adaptive passes.
34
Changing the Coordinate System Associated with the Magnets

In Session II, we specified in Maxwell that the permanent magnets on the Air-X rotor had spherical fields
emanating from the origin (i.e., the center of the rotor). However, looking at the iron filings around the
actual magnets, shown in Figure 18, it appears that the origin of the magnets spherically oriented fields
is much closer to the magnets, and the fields also appear to decay toward the magnets edges. We
would need more information to create a precise model of these magnetic fields, but as a first step
toward improving the fields accuracy (and to gain experience with a valuable tool in Maxwell), you will
create new coordinate systems that will serve as the basis for the magnets field lines. These coordinate
systems will rotate along with the magnets.
To start, go back to the model version that you used when changing the time step the model with the
less precise mesh and the time step of 0.5 ms but edit Analysis->Setup1 in the Project Manager
window to increase the Stop time to 20 ms. Alt-double-click in the lower-center portion of the graphing
window to view the model from below, and ensure that the Global coordinate system is selected in the
Model Tree. Press the f key to select faces, and click on the rotor. Then click on the Create face CS
toolbar icon
. In the lower-right corner of the software window, change the pull-down from
Cartesian to Spherical, ensure that Absolute is selected in the adjacent pull-down menu, and enter the
following values (remember to Tab between entries and press Enter when youre done): Rho = 20 mm,
Theta = 90 deg, Phi = 15 deg. Then click on the center of the magnet face above this point (the cursor
should turn into a triangle, and the entry boxes at the bottom of the screen should read dRho = 18.3 cm,
dTheta = 90 deg, and dPhi = 15 deg). Expand the Coordinate Systems list in the Model Tree to see your
new coordinate system, called FaceCS1. Select it, and change its name to North_CS. Then select the
north magnets name in the Objects list, Magnet_N, and via the Properties window (Attribute tab)
change the north magnets Orientation to North_CS. The magnets spherical field vectors will now be
associated with this offset coordinate system.
Select the Global coordinate system from the Model Tree, and repeat the process for creating the
south magnets coordinate system: Select the face of the rotor, press the Create face CS toolbar icon;
make it a Spherical coordinate system; set Rho = 20 mm, Theta = 90 deg, and Phi = 45 deg; click on the
bottom-center of the other magnet (dRho = 18.3 mm, dTheta = 90 deg, dPhi = 45 deg); rename the new
coordinate system from FaceCS1 to South_CS; and assign the Orientation of the Magnet_S object
to the new South_CS coordinate system. The new coordinate systems should look similar to those
shown in Figure 29. (You can see the coordinate systems by selecting their associated items on the
Model Tree while pressing the CNTL key.) Save a screenshot of your magnets coordinate systems. Select
the Global coordinate system, press the o key to return to the object rather than the face selection
mode, and Alt-double-click on the upper-right corner of the graphing window to return to the default
view.
Select Maxwell 3D->Analyze All to run this simulation, save a screenshot of the resulting magnetic flux
and induced voltage plots, and compare the result of altering the magnets coordinate systems to your
previous results.
35
Figure 29. Revised coordinate systems for the north and south magnetic poles in the reduced Air-X model.
Altering the Air-X Design

Make a list of several parameters that you could change in the Air-X model or the simulation settings,
and predict the effect that each of these changes would have on the final result. Implement one of these
changes in your Maxwell 3D model of the Air-X generator, and run the simulation. Try to pick different
modifications than other students, and compare your findings with each other. Record and interpret
your results. Congratulations, youre done with the simulations!

Screenshot of the plot showing the magnetic flux through and the induced EMF across the Phase
A and Phase B coils when the time step is 0.5 ms. Comparison between this plot, the plot
generated in Session II with a step of 1.0 ms, and the plots shown in Figure 27 of the procedures
which show time steps of 0.2 and 0.1 ms.
Obtain screenshots of objects meshes after 5 adaptive passes. There should be one screenshot
focusing on the curved side of the magnets, one screenshot focusing on the side of the rotor
teeth facing the magnets, and a couple screenshots showing the combined coils, stator, rotor,
and magnets. Discuss how these meshes differ from those obtained in the previous session.
Obtain a screenshot of the plot of the magnetic flux through and EMF induced across the Phase
A coil as a function of time, when the refined mesh is used and the time step is 0.5 ms. Compare
this result to the one obtained in the previous section, where the time step was 0.5 ms but the
mesh was not as refined.
36
Save a screenshot of your magnets altered coordinate systems, as well as a screenshot of the
resulting magnetic flux through and voltage induced across the Phase A coil after the magnets
coordinate systems have been altered. Compare this plot to those obtained previously.
List several parameters that you could change in the Air-X model or the simulation settings,
along with your predictions of the effects that each of these changes would have on the final
result. Try one of these changes, and obtain and interpret a screenshot of the resulting
simulations output. Compare these and the earlier results to actual Air-X measurements.
Additional Concept and Design Questions:
Why do you think that the Air-X manufacturers took special care to smooth sharp edges in the
magnets and stator slots?
37

EE364 Maxwell Simulation Assignment 1

Uploaded by

Copyright:

Available Formats

EE364 Maxwell Simulation Assignment 1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EE364 Maxwell Simulation Assignment 1

Uploaded by

Copyright:

Available Formats

El

Electromagnetics in Power Engineering

Figure 1. Southwest Windpower Air-X wind generator (http://windenergy.com)

Session I Modeling the Air-X Rotor and Stator

Session I - Modeling the Air-X Rotor and Stator

Figure 2. Rotor of Southwest Windpower Air-X wind generator.

Initializing Global Variables

Session I Modeling the Air-X Rotor and Stator

Importing and Editing User Defined Primitives of the Rotor

Session I Modeling the Air-X Rotor and Stator

Tips & Tricks: Changing the view of your model

Alternatively, selecting the Alt key and then double-clicking in the

Session I Modeling the Air-X Rotor and Stator

Session I Modeling the Air-X Rotor and Stator

Session I Modeling the Air-X Rotor and Stator

Session I Modeling the Air-X Rotor and Stator

Figure 7. Ansoft/Ansys Maxwell 3D model of the Air-X rotor.

Session I Modeling the Air-X Rotor and Stator

Additional Rotor Concept and Design Questions

Session I Modeling the Air-X Rotor and Stator

Creating a Model of the Stator

Figure 10. Overhead view of a section of the Air-X stator.

Session I Modeling the Air-X Rotor and Stator

Hs0, Slot opening height = 0.8 mm

Session I Modeling the Air-X Rotor and Stator

Rs, Slot body bottom fillet = 2 mm

Session I Modeling the Air-X Rotor and Stator

Creating the Coils

LayerLoc, (0: whole; 1: middle; 2: top; 3: bottom) = 3

Session I Modeling the Air-X Rotor and Stator

Figure 13. ConCoil parameters used to model an Air-X stator coil.

Session I Modeling the Air-X Rotor and Stator

Session I Modeling the Air-X Rotor and Stator

Additional Stator Concept and Design Questions

Summary of Specific Information Requested for the Lab Report

Session I Modeling the Air-X Rotor and Stator

Additional Concept and Design Questions:

Include a picture of a lap coil and a wave coil for reference.

Session II Setting the Initial Simulation Parameters

Session II Setting the Initial Simulation Parameters

Session II Setting the Initial Simulation Parameters

Figure 16. Symmetric section of the Air-X model.

Specifying the Magnets Fields

Session II Setting the Initial Simulation Parameters

Defining the Region where Electromagnetic Fields will be Calculated

Session II Setting the Initial Simulation Parameters

Figure 19. XZ rectangle used to define the computation region.

Session II Setting the Initial Simulation Parameters

Clarifying Edge Symmetries through Master/Slave Boundaries

Session II Setting the Initial Simulation Parameters

Defining the Rotors Rotation

Session II Setting the Initial Simulation Parameters

Session II Setting the Initial Simulation Parameters

Setting Coil-Specific Simulation Parameters

Session II Setting the Initial Simulation Parameters

Setting up Miscellaneous Simulation Parameters

Session II Setting the Initial Simulation Parameters

Running the Simulation!

Obtaining Initial Simulation Results