Scribd
Upload
2K views4 pages

Module SIPO

The document contains Verilog code for various shift register designs including: - A 4-bit serial-in parallel-out shift register with clock, reset and serial data input. - Several 8-bit serial-in serial-out shift registers with different clocking schemes like positive edge, negative edge, asynchronous clear, synchronous set. - An 8-bit serial-in parallel-out shift register. - An 8-bit shift register with asynchronous/synchronous parallel load in addition to serial input. - An 8-bit shift-left/right register that can shift in either direction.

Uploaded by

VenkatGolla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
2K views4 pages

Module SIPO

The document contains Verilog code for various shift register designs including: - A 4-bit serial-in parallel-out shift register with clock, reset and serial data input. - Several 8-bit serial-in serial-out shift registers with different clocking schemes like positive edge, negative edge, asynchronous clear, synchronous set. - An 8-bit serial-in parallel-out shift register. - An 8-bit shift register with asynchronous/synchronous parallel load in addition to serial input. - An 8-bit shift-left/right register that can shift in either direction.

Uploaded by

VenkatGolla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

module SIPO ( din ,clk ,reset ,dout );

output [3:0] dout ;


wire [3:0] dout ;
input din ;
wire din ;
input clk ;
wire clk ;
input reset ;
wire reset ;
reg [3:0]s;
always @ (posedge (clk)) begin
if (reset)
s <= 0;
else begin
s[3] <= din;
s[2] <= s[3];
s[1] <= s[2];
s[0] <= s[1];
end
end
assign dout = s;

endmodule

Verilog code for an 8-bit shift-left register with a positive-edge clock, serial in and serial out.
module shift (clk, si, so);
input
clk,si;
output
so;
reg
[7:0] tmp;
always @(posedge clk)
begin
tmp
<= tmp << 1;
tmp[0] <= si;
end
assign so = tmp[7];
endmodule

Verilog code for an 8-bit shift-left register with a negative-edge clock, a clock enable, a serial in
and a serial out.

module shift (clk, ce, si, so);


input
clk, si, ce;
output
so;
reg
[7:0] tmp;
always @(negedge clk)
begin
if (ce) begin
tmp
<= tmp << 1;
tmp[0] <= si;
end
end
assign so = tmp[7];
endmodule
Verilog code for an 8-bit shift-left register with a positive-edge clock, asynchronous clear, serial in
and serial out.
module shift (clk, clr, si, so);
input
clk, si, clr;
output
so;
reg
[7:0] tmp;
always @(posedge clk or posedge clr)
begin
if (clr)
tmp <= 8b00000000;
else
tmp <= {tmp[6:0], si};
end
assign so = tmp[7];
endmodule
Verilog code for an 8-bit shift-left register with a positive-edge clock, a synchronous set, a serial in
and a serial out.
module shift (clk, s, si, so);
input
clk, si, s;
output
so;
reg
[7:0] tmp;
always @(posedge clk)
begin
if (s)
tmp <= 8b11111111;
else
tmp <= {tmp[6:0], si};
end
assign so = tmp[7];
endmodule

Verilog code for an 8-bit shift-left register with a positive-edge clock, a serial in and a parallel out.

module shift (clk, si, po);


input
clk, si;
output [7:0] po;
reg
[7:0] tmp;
always @(posedge clk)
begin
tmp <= {tmp[6:0], si};
end
assign po = tmp;
endmodule

Verilog code for an 8-bit shift-left register with a positive-edge clock, an asynchronous parallel
load, a serial in and a serial out.
module shift (clk, load, si, d, so);
input
clk, si, load;
input [7:0] d;
output
so;
reg
[7:0] tmp;
always @(posedge clk or posedge load)
begin
if (load)
tmp <= d;
else
tmp <= {tmp[6:0], si};
end
assign so = tmp[7];
endmodule

Verilog code for an 8-bit shift-left register with a positive-edge clock, a synchronous parallel load,
a serial in and a serial out.
module shift (clk, sload, si, d, so);
input
clk, si, sload;
input [7:0] d;
output
so;
reg
[7:0] tmp;
always @(posedge clk)
begin
if (sload)
tmp <= d;
else
tmp <= {tmp[6:0], si};
end
assign so = tmp[7];
endmodule

Verilog code for an 8-bit shift-left/shift-right register with a positive-edge clock, a serial in and a
serial out.
module shift (clk, si, left_right, po);
input
clk, si, left_right;
output
po;
reg
[7:0] tmp;
always @(posedge clk)
begin
if (left_right == 1b0)
tmp <= {tmp[6:0], si};
else
tmp <= {si, tmp[7:1]};
end
assign po = tmp;
endmodule

You might also like