AC 140 HangerSupport

KENCANA SQUARE
HANGER, ANCHORS AND SUPPORTS

SECTION AC-140
Page 1
1.0
GENERAL
1.1
DESCRIPTION
.1
1.2
1.3
Work of this Section shall conform to the requirements of the Contract

Documents.
WORK INCLUDED
.1
Hangers.
.2
Structure Attachments,
SUBMITTALS
.1
Product Data: Manufacturer's latest published data for materials,

equipment and installation.
.2
Shop Drawings: Submit details of pipe hangers, anchors and supports for
each pipe size and pipe service. Submit details of support methods and
point loadings, and anchor reactions.
2.0
PRODUCT
2.1
PIPE SUPPORTS & ANCHORS

.1
All piping shall be supported by means of pipe supports in accordance

with the relevant British Standard Specification.
.2
All pipes supports shall be steel, adjustable for height and prime coated
with rust preventive paint and finish coated black, in the types shown in
the following table. This table does not apply for buried pipes.
Services
Pipe Size
Type of Support
Chilled Water
All Sizes
Clevis Hanger (Single)

Trapeze (Multiple)
Hot Water
12mm to 150mm
-do-
Hot Water
More than 150mm
Roller or Spring
Steam
12mm to 50mm
Clamp
Steam
More than 65mm
Roller or Spring
Drain
6mm-up
Clamp
Compressed Air
6mm-up
Clamp
Water (Drinking
or Condensing)
Saddle or clamp or
otherwise as approved
DAMANSARA CITY MIXED DEVELOPMENT (PARCEL 2)

SECTION AC-140
Page 2
.3
All buried pipes shall be laid in accordance with manufacturers

recommendations and/or local codes and ordinances.
.4
Vertical risers when passing through each floor slab shall be supported to
the floor by means of clamps, collars or pipe guides attached to the pipe
which in turn shall be attached to angles as per the following schedule:
Service
Support
Chilled Water
Spring(Within Chilled Water Plantroom)

Vibration Isolator (Other areas)
Hot Water
Spring
Steam
Spring
Cold Water Pipe
Cradles
Drain Pipes
12mm Rubber Pad
Compressed Air
12mm Rubber Pad
Condensing Water Pipes
Spring or as approved
Medical Gases
Pipes Clips to walls
Vertical risers shall be supported at the lowest point in accordance with

the following schedule unless otherwise stated.
Height of Riser
Pipes Size
Type of Support
Under 20
Up - 4
Hanger at Elbow
Under 20
6- 8
Support or concrete block
Under 20
10- up
Foot elbow
Over 20
Up to 1
Hanger at elbow
Over 20
1 6
Support or concrete
Over 20
7 and up
Foot elbow
.5
In instances where the pipes and clamp are of different materials, an

approved type of gasket shall be inserted between the pipe and clamp.
.6
Insulated pipes shall be supported such that the insulation is not

damaged due to undue pressure on it. Care shall be taken to ensure that
the vapour seal around the supports is uninterrupted.
.7
The hangers shall be fixed to the main structure by means of expanding

metal plugs and steel bolts and arranged to be loaded in shear.
.8
All piping shall generally be graded to eliminate air pockets or gas locks
depending on the service.
.9
The piping installation shall incorporate provisions for the venting of high
points and drawings of low points.
KENCANA SQUARE
SECTION AC-140
Page 3
3.0
EXECUTION
3.1
INSTALLATION
.1
Support horizontal piping in accordance with the following schedule:

Pipe Size
Maximum Hanger
Spacing
Minimum Rod
Size
25mm and smaller
1800mm
10mm
32mm to 50mm
2700mm
10mm
65mm to 80mm
3000mm
15mm
100mm to 125mm
3600mm
15mm
150mm
3600mm
20mm
200mm to 300mm
3600mm
25mm
350mm to 400mm
3600mm
25mm
450mm
3600mm
30mm
500mm
3600mm
35mm
600mm
3600mm
40mm
750mm
3600mm
40mm
1000mm
3600mm
50mm
1200mm
3600mm
50mm
.2
Provide hangers at each change in direction and both sides of each valve.
.3
Provide drilled expansion type inserts to the reinforced concrete.

structural slab for pipe supports.
.4
Regardless of the type of construction (i.e., concrete, concrete-deck-steel

or other variations) take particular care to support all main lines and all
large and heavy pipes in an approved manner, including the furnishing
and installation of supplementary steel, if required. Supplementary steel
sections are to be mill-rolled. Submit shop drawings, indicating support
methods, point loadings to the building structure and hanger locations for
review sufficiently in advance of concrete pouring schedules to permit
evaluation, critique and any necessary changes to handling and support
methods.
.5
Provide approved roller support, floor stands, wall brackets, etc., for all
lines running near the floor or near walls, which can be properly
supported or suspended by the floors or walls. Pipelines near walls may
also be hung by hangers carried from approved wall brackets at a level
higher than the pipe.
.6
Do not hang piping from other piping. Support of hangers by means of

vertical expansion bolts is not permitted.
DAMANSARA CITY MIXED DEVELOPMENT (PARCEL 2)

SECTION AC-140
Page 4
.7
Wherever hangers using pipe rolls are used provide approved steel pipe
covering protection saddles, spot welded to the piping at each hanger
location.
.8
Anchor piping and as required to localise expansion or to

strain on piping and branches. Anchors to be entirely
hangers. All anchor designs to be submitted for approval
piping reactions which respective anchors are capable
Provide all indicated or required expansion loops.
.9
Support all lines for copper tubing individually by approved type hangers
not more than 2m apart, or as shown on the drawings. Use hangers
especially designed for copper tubing and of exact outside diameter of
tubing. On hangers for covered tubing, use broad straps fitting outside of
covering.
.10
Hangers used for cold piping will support the pipe without piercing the
insulation. Use insulation shields to protect the insulation on cold pipes.
Weld insulation protection saddles to insulated hot pipes, or any piping
subject to axial movement, at roller supports. Space between pipe and
saddle to be filled with insulation.
.11
For piping 100mm and larger, support the elbows of the piping adjacent to
the pumps with steel base elbow supports from the inertia base which
pump is on to prevent loading heavy weights of piping on pump casing.
Where inertia base is not provided, base elbows to be supported on floor
with 25mm neoprene pad.
.12
Scratches and cut ends to be field touched up with protective paint or

galvanising agent.
END OF SECTION AC-140
prevent undue
separate from
and to include
of supporting.

AC 140 HangerSupport

Uploaded by

Copyright:

Available Formats

AC 140 HangerSupport

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AC 140 HangerSupport

Uploaded by

Copyright:

Available Formats

KENCANA SQUARE

HANGER, ANCHORS AND SUPPORTS

Work of this Section shall conform to the requirements of the Contract

Product Data: Manufacturer's latest published data for materials,

PIPE SUPPORTS & ANCHORS

All piping shall be supported by means of pipe supports in accordance

Clevis Hanger (Single)

More than 150mm

More than 65mm

DAMANSARA CITY MIXED DEVELOPMENT (PARCEL 2)

All buried pipes shall be laid in accordance with manufacturers

Spring(Within Chilled Water Plantroom)

Cold Water Pipe

12mm Rubber Pad

12mm Rubber Pad

Condensing Water Pipes

Pipes Clips to walls

Vertical risers shall be supported at the lowest point in accordance with

Support or concrete block

In instances where the pipes and clamp are of different materials, an

Insulated pipes shall be supported such that the insulation is not

The hangers shall be fixed to the main structure by means of expanding

Support horizontal piping in accordance with the following schedule:

25mm and smaller

Provide drilled expansion type inserts to the reinforced concrete.

Regardless of the type of construction (i.e., concrete, concrete-deck-steel

Do not hang piping from other piping. Support of hangers by means of

DAMANSARA CITY MIXED DEVELOPMENT (PARCEL 2)

Anchor piping and as required to localise expansion or to

Scratches and cut ends to be field touched up with protective paint or

END OF SECTION AC-140

You might also like