Lecture 4. Pipes Materials and Loads1 PDF

The Islamic University of Gaza- Civil Engineering Department
Sanitary Engineering- ECIV 4325
L4. Pipes Materials and Loads
Based on Dr. Fahid Rabah lecture notes
Pipes Materials and loads
Materials used for pipes:
Factors effecting the selection of materials:
Sewers are made from:

1- Concrete
2- Reinforced concrete
3- Vitrified clay
4- Asbestos cement
5- Cast iron (lined with cement).
6- Ductile iron (lined with cement).
7- Steel (lined with cement).
8- PVC, UPVC
9- GRB (fiber glass).
1- Chemical characteristics of wastewater and degree of

resistance to acid, base, solvents,
2- Resistance to scour and flow (friction coefficient).
3- External forces and internal pressures.
4- Soil conditions.
5- Type of backfill
6- Useful life
7- Strength and water tightness of joints and effective
control of infiltration and inflow.
8- Availability in diameter, length, and ease of
installation.
9- Cast of construction and maintenance.
Loads on pipes
When pipes are buried, many forces affect them. The following are the main forces expected
to affect buried pipes:
A- Loads due to Back fill:
Back fill load on a pipe depends on:
Trench width
Depth of excavation
Unit weight of the fill material
Frictional characteristics of the backfill.
These factors are formulated in the following formula:
= 9 .8 C
* *B 2
d
d
where,
Wd = load on buried pipe as due to backfill (Newton per linear meter)
Cd = Coefficient based on the type of backfill and ratio of trench depth
to width.
= Density of backfill, kg/m3

Bd = Width of trench at top of the pipe, (m)
Example (1)
Calculate the backfill load on a 610 mm pipe given the following information:
Backfill depth (H) = 3.6 m
Trench width at the top of the pipe is 1.2 m
Backfill is saturated clay, P = 1920 kg/m3
Solution
H/Bd = 3.6/1.2 = 3 from the figure Cd=2.2
Or you can calculate Cd from the equation
= 9 .8 C
* *B 2
d
d
= 9 . 8 x 2 . 2 * 1920 * (1 . 2 ) 2
= 6082 N/m
B. Wheel loads from trucks

Wheel loads from trucks and vehicles transmit live loads to buried sewer lines.
When the sewer is deep, only a small portion of the load is transmitted to the sewers.
Equations to compute live loads are very complex thats why designers pre-calculated data as illustrated by
tables
Table gives the highway truck loads transmitted to buried circular pipe in kN/m. The information needed are:
Pipe diameter (d). Height of fill (H) above pipe (m).
Note: The load is based on (71.17 kN dual-tire wheel load).
If the cover fill is less than ( 1m ) the value obtained from table
Should be multiplied by an impact factor obtained from next table.
Example (2)
Calculate the wheel load on a 610 mm pipe that has a backfill cover of 0.8 m.
Solution
From the table the wheel load is 14.15 kN / m (by interpolation)
Since H = 0.80 m and in the range (0.61 m 0.90 m) use table to find the impact factor
of 1.1
Truck load = 14.15 X 1.1 = 15.57 KN/m.
C- Superficial loads on buried pipes:

Superficial loads are produced by buildings and other structures crossing the trench or built
along the trench.
The proportion of superficial loads that reach the pipe is estimated in tables 1 and 2; the
forces are divided into two types:
Long superficial Length of Application > trench Width.
Short superficial Length of Application trench Width.
To find the portion of superficial load transmitted to the pipes from tables 1 and 2 one should
know :
a. Depth of trench
b. Width of trench
c. Soil type
1
L
W
For table 2, the minimum values are for
10
Note: [The truck load can be also estimated as a superficial load].
Trench
Structure
Trench
[Short superficial load]
Structure
L
W
[Long superficial load]
Table 1. Proportion of long superficial loads

reaching pipe in trench
Table 2. Proportion of short superficial

loads reaching pipe in trench
Max when L=W
Min when L=<0.1 W
Example (3)
A concrete structure 0.91 m wide with a weight of 1340 kg/m crosses a trench
1.22 m wide in damp clay. The structure bears on the soil 1.83 m above the top
of the pipe. Find the load transmitted to the pipe.
Solution
The load applied by the structure is 1340X1.22= 1635 kg
The pressure applied to the soil above the pipe is
P= 1635/0.91= 1795 kg/m
The ratio of depth to the width is 1.83/1.22= 1.5 From table 2, the maximum
proportion of the load reaching the pipe will be 0.51.
Therefore the load reaching the pipe will be
Trench
P = 1795X0.51=915 kg/m
Structure
L= 0.91 m
W=1.22 m
Strength of pipes:
The crushing strength of sewer pipes is determined by the three-edge bearing test. The pipe
is stressed until failure occurs. Table (3) gives the minimum crushing strength for clay
pipes.
Strength requirements for reinforced concrete pipes are given in table 4, for this table the
crushing force correspond to 0.25mm crack. The values in the table are pre mm diameter,
thats why they are called D-Loads (KN/m.mm)
The pipe strength in supporting loads depends on the method of pipe bedding :
- Class (D) bedding support the three bearing load only.
- Class(C) support (1.5) the three edge load (1.5 = Load factor)
- Class (B) bedding has a load factor of 1.9.
- Class (A) bedding has a load factor of 2.3 to 3.4.
- Other pipe material has similar tables to estimate their strength
The three- edge bearing test
Example (4)
A 610 mm concrete pipe is subjected to a load of 40 KN/m (backfill and wheel load). The
D-load of the pipe to produce 0.25 mm crack is 38.3N/m.mm (The three edge test
strength). The pipe bedding is Class A with a load factor of 3.4.
a) What is the strength of this pipe
b) Is the strength enough to resist the applied load if the minimum factor of safety is 1.5
c) What is the final factor of safety in this case
Solution
a) Strength of the pipe= the three edge test strength X bedding load factor =
(38.3X610)X3.4= 79434.2 N/m = 79.4 KN/m
b) Factored applied stress = applied stress X load factor = 40X 1.5= 60 KN/m.
c) Since the strength is 79.4 KN/m > factored applied stress (60 KN/m), so the strength
is enough.
Factor of safety = pipe strength/ applied stress= the three edge test strength X bedding
load factor/ applied stress.

Lecture 4. Pipes Materials and Loads1 PDF

Uploaded by

Copyright:

Available Formats

Lecture 4. Pipes Materials and Loads1 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture 4. Pipes Materials and Loads1 PDF

Uploaded by

Copyright:

Available Formats

The Islamic University of Gaza- Civil Engineering Department

Sanitary Engineering- ECIV 4325

L4. Pipes Materials and Loads

Based on Dr. Fahid Rabah lecture notes

Pipes Materials and loads

Materials used for pipes:

Factors effecting the selection of materials:

Sewers are made from:

1- Chemical characteristics of wastewater and degree of

= Density of backfill, kg/m3

B. Wheel loads from trucks

C- Superficial loads on buried pipes:

[Short superficial load]

[Long superficial load]

Table 1. Proportion of long superficial loads

Table 2. Proportion of short superficial

The three- edge bearing test

You might also like