Atp Procedure

OLT MA5600T
Acceptance Test Guide
OLT ACCEPTANCE TEST PROCEDURE

For
OLT SMT PROJECT - Batch 1
PT. SERPONG MAS TELEMATIKA

OLT Site Name : SINARMAS LAND PLAZA MMR-1
Document Prepared by Huawei and Approved by SMT
Huawei Technologies Co., Ltd
OLT MA5600T
ii
OLT MA5600T
TABLE OF CONTENT
Table of Content
...............................................................................................................................................................i
T01 Equipment Test................................................................................................................................................1
T01-01 Visual Check........................................................................................................................................1
T01-0101 Hardware Installation..............................................................................................................1
T01-02 Maintenance & Management...............................................................................................................2
T01-0201 Serial Port Mode.....................................................................................................................2
T01-0202 Outband Telnet Mode..............................................................................................................2
T01-0203 Inband Telnet Mode................................................................................................................3
T01-03 Board Management Test......................................................................................................................3
T01-0301 Auto-finding & Confirming Service Board............................................................................3
T01-0302 Disabling/Enabling a PON Port..............................................................................................5
T01-0303 Resetting Boards.....................................................................................................................6
T01-0304 Rebooting The System............................................................................................................7
T02 Basic Configuration Test.................................................................................................................................7
T02-01 Admin Login........................................................................................................................................7
T02-02 Management VLAN Configuration.....................................................................................................7
T02-0201 Creating a VLAN....................................................................................................................7
T02-0202 Adding a VLAN to a Port.......................................................................................................8
T02-03 Management IP Configuration.............................................................................................................8
T02-0301 Creating an IP Address & Subnetmask...................................................................................8
T02-0302 Creating a Default Route........................................................................................................9
T02-04 Ping Reachability.................................................................................................................................9
T02-0401 IP Gateway Ping......................................................................................................................9
T02-0402 IP NMS Ping.........................................................................................................................10
T02-05 Saving the Configuration...................................................................................................................10
T03 Reliability Test...............................................................................................................................................11
T03-01 Switchover Test..................................................................................................................................11
T03-0101 Active/Standby Switchover of Control Boards.....................................................................11
T03-0102 Backup Protection of Power Boards.....................................................................................12
T03-02 Uplink Protection Test.......................................................................................................................13
T03-0201 Uplink Port 1+1 Backup.......................................................................................................13
T04 Service Function Test.....................................................................................................................................16
T04-01 Triple Play Test..................................................................................................................................16
T04-0101 Multiple Service Profile........................................................................................................16
T04-0102 GPON OLT HSI Service.......................................................................................................17
T04-0103 GPON OLT OTT Service......................................................................................................19
T04-0104 GPON OLT Voice Service....................................................................................................21
iii
OLT MA5600T
iv
OLT MA5600T
GPON OLT MA5600T

T01 Equipment Test
T01-01 Visual Check
T01-0101 Hardware Installation
Purpose
To check whether the cabinet installation meets the requirements
Network diagram
None
Prerequisite
The cabinet installation must be completed.
Procedure
Verify the quantity of all racks, equipments, cables & accessories.

Check the cabinet appearance.
Check the inside of the cabinet.
Check the cable suit.
Check whether the boards are properly installed & connected to optical fibers and user
cables.
Check the front panels of the boards.
Check the connections of the fuses, power cables and ground cables.
Check the cabinet door and the side panel.
Check the sub rack fan modules
Check all the labels for racks, equipments & cables.
Expected results
1.
In step 1, all the quantity are match with Bill of quantity
2.
In step 2, the cabinet appearance is clean without distortion, scratch, and rustiness.
3.
In step 3, there are no sundries in the cabinet, the bolts are fastened tightly, and no
component in the cabinet is rusty. In addition, the air filter is installed and in clean
condition.
4.
In step 4, the cable suit is complete and the spare cables are bundled properly.
5.
In step 5, the boards are properly installed & connected to optical fibers and
user cables.
6.
In step 6, the front panels are clean; the silk screen is consistent with the board
name and there is no scratch.
7.
In step 7, the fuses, power cables are connected properly and the cabinet is
grounded.
8.
In step 8, the cabinet door, the side panel, and the body of the cabinet are properly
grounded, and the cabinet door can be opened and closed easily.
9.
In step 9, the sub rack fan modules are running well
10. Racks, Equipments & cables are labeled properly

Remarks
SCUN = Control board, GBPD/GBPH = GPON board, X2CS = 10GE uplink board
OLT MA5600T
T01-02 Maintenance & Management

T01-0201 Serial Port Mode
Purpose
To verify the maintenance function of the local serial port
Network diagram
None
Prerequisite
The MA5600T must be powered on and must work in the normal state.
The maintenance serial port of the main control card works in normal state.
Procedure
Expected results
Remarks
1.
Use the maintenance serial port cable to connect the maintenance serial port (com
port) of the main control card with one of the serial ports (usually serial port 1) of
the maintenance terminal.
2.
Run the HyperTerminal, enter the connection description, select the corresponding
serial port, and configure its property as follows: 9600bit/s for baudrate, 8 for data
bit, None for parity check, 1 for stop bit, and None for flow control.
3.
After finishing the configuration, use this serial port for connection.
4.
Enter the user name: huawei and the password: r00tw3rk#@! to log in the system.
5.
Run some commands.
The communication of the serial port is in good condition, the login is successful, and
the commands can be executed correctly.
The default baud rate of the maintenance serial port is 9600 bit/s.
T01-0202 Outband Telnet Mode

Purpose
To verify the maintenance function by Telnet session
Network diagram
None
Prerequisite
The network interface card & IP address of the maintenance terminal has been properly
configured.
Procedure
1.
Connect ethernet cable from laptop to the m-eth port of the control card SCUN
2.
Run Telnet on the maintenance terminal using hyperterminal or other telnet

application
3.
Enter the IP address of the network port of main control card into the Telnet
window of the maintenance terminal.
4.
Log in, and run some commands.
Expected results
The connection is normal, the login is successful, and the commands can be executed
successfully.
Remarks
You can use the ping command to check whether the communication between the
maintenance terminal and the control card is in normal state.
The outband ip address of control card is: 192.168.1.1
OLT MA5600T
T01-0203 Inband Telnet Mode

Purpose
To verify the maintenance function by inband telnet session
Network diagram
Prerequisite
The OAM-IP address has been properly configured.
Procedure
1.
Log in to the MA5600T (OLT-1) using serial or outband mode.
2.
Run telnet command on the OLT-1 CLI to OLT-2 OAM ip-address using
hyperterminal or other telnet application
3.
After succeed logging into OLT-2, run some commands.
Expected results
The connection is normal, the login is successful, and the commands can be executed
successfully.
Remarks
You can use the ping command to check whether the communication 2 OLTs are in
normal state.
The OAM ip-address can be set based on the data provided, attached with this
document.
T01-03 Board Management Test

T01-0301 Auto-finding & Confirming Service Board
Purpose
To verify the function of automatically finding a service board and confirming the
service board
Network diagram
None
Prerequisite
You must be logged in to the MA5600T from a PC through the upstream port in the
inband management mode or through the maintenance network port in the outband
management mode (telnet IP Address 192.168.1.1) or using console port. Ensure that the
MA5600T can be maintained normally.
Procedure
In the global config mode, run the display board 0 command to query the board status.
Insert a board into an idle slot.
In the global config mode, run the display board 0 command to query the board status.
Run the board confirm command to confirm the board inserted in step 1.
Run the display board 0 command to query the board status.
Expected results
In step 3, you can confirm that the board is automatically found and is in the auto-find
state.
3
OLT MA5600T
In step 5, you can confirm that the board is in the normal state.
(Insert the normal command output here)
huawei> display board 0
Command:
display board 0
----------------------------------------------------------SlotID
BoardName Status
SubType0 SubType1 online/Offline
----------------------------------------------------------0
1
H802GPBD Normal
H802GPBD Normal
H802GPBD Normal
H802GPBD Normal
H802GPBD Normal
H802GPBD Normal
H802GPBD Normal
H802GPBD Normal
H801SCUN Active_normal
10
H801SCUN Standby_normal
11
12
13
14
15
16
17
H802GPBD Auto-find
18
H802GPBD Auto-find
19
20
Remarks
21
H801PRTE Normal
22
H801PRTE Normal
The auto-find state of the board can be queried through the display board 0 command
only after the MA5600T reports the alarm of automatically finding a board.
T01-0302 Disabling/Enabling a PON Port

4
OLT MA5600T
Purpose
To verify the function of disabling and enabling a PON port
Network diagram
None
Prerequisite
inband management mode or through the maintenance network port in the outband
management mode (telnet IP Address 192.168.1.1) or using console port. Ensure that the
MA5600T can be maintained normally.
Procedure
In the global config mode, run the interface gpon 0/1 command to enter the gpon
interface mode.
In the gpon interface mode, run command ont add 0 0 sn-auth 4857544353BA0409
omci ont-lineprofile-id 1 ont-srvprofile-id 1 to add an ONT to PON port 0.
Input command display port state 0 to query the state of pon port 0.
Run the shutdown 0 command to disable the port 0.
Run command display port state 0 to query the state of pon port 0.
Run the undo shutdown 0 command to enable the port 0.
Run command display port state 0 to query the state of pon port 0.
Expected results
In step 3, you can confirm that port is online

In step 5, you can confirm that port is offline
In step 7, you can confirm that the port is online
huawei(config-if-gpon-0/1)#shutdown 0
huawei(config-if-gpon-0/1)#display port state 0
---------------------------------------------------------------------------F/S/P
0/18/0
Optical Module status

Port state
Online
Offline
---------------------------------------------------------------------------huawei(config-if-gpon-0/1)#undo shutdown 0
huawei(config-if-gpon-0/1)#display port state 0
---------------------------------------------------------------------------F/S/P
0/18/0
Optical Module status

Port state
Online
Online
----------------------------------------------------------------------------
Remarks
T01-0303 Resetting Boards

Purpose
To check whether a board can return to the normal state after reset
5
OLT MA5600T
Network diagram
None
Prerequisite
1.
The cabinet must be powered on and must work in the normal state.
2.
The MA5600T must work in the normal state.
1.
In the global config mode, run the display board 0 command to query the
service & control board status.
2.
Remove a service board and insert the service board back without powering
off the MA5600T, and then check whether the board is in the normal state
after reset.
3.
service board status.
4.
Press the RESET button on the front panel of the control board to reset the
control board, and then check whether the control board recovers after reset.
5.
control board status.
6.
Run the board reset command to reset a service board, and then check
whether the service board recovers after reset
7.
service board status.
1.
In step 3, the service board is in the normal state.
2.
In step 4, the active control board will be switched-over to standby board.
3.
In step 5, the control board is in the normal state after reset.
4.
In step 7, the service board is in the normal state after reset.
5.
The OLT configuration doesnt change after board resetting.
Procedure
Expected results
Remarks
Board status is failed when service board is removed.

SCUN = Control board, GBPD/GBPH = GPON board, X2CS = 10GE uplink
board
T01-0304 Rebooting The System

6
OLT MA5600T
Purpose
To check whether the MA5600T can be rebooted without errors
Network diagram
None
Prerequisite
1.
2.
1.
In the global config mode, run the save command to save the existing
configuration
2.
In the global config mode, run the reboot system command to reboot the
MA5600T
1.
The MA5600T can be rebooted successfully without no errors
2.
The OLT configuration doesnt change after system rebooting
Procedure
Expected results
Remarks
T02 Basic Configuration Test

T02-01 Admin Login
Purpose
To verify the function of logging in the system using admin user
Network diagram
None
Prerequisite
Procedure
1.
Access the MA5600T using serial or telnet mode
2. Enter the system using admin username: huawei and admin password:
r00tw3rk#@!
Expected results
The system can be accessed using admin account successfully
Remarks
T02-02 Management VLAN Configuration

T02-0201 Creating a VLAN
Purpose
To verify the function of creating a VLAN on the system
Network diagram
None
Prerequisite
Procedure
1.
Enter the global config mode,
2.
Run the command: vlan 1000 smart to create vlan with id 1000 and type is smart
3.
Run the command: display vlan all
Expected results
In step 2, the vlan can be created successfully

In step 3, the vlan can be queried successfully
7
OLT MA5600T
Remarks
The vlan can be set based on the data provided, attached with this document.
T02-0202 Adding a VLAN to a Port

Purpose
To verify the function of adding a vlan to a specified port
Network diagram
None
Prerequisite
The vlan has been configured properly (refer to T02-0201)
Procedure
Expected results
1.
2.
Run the command: port vlan 1000 0/19 0 to to add vlan 1000 to the port 0/19/0
3.
Run the command: display port vlan 0/19/0
In step 2, the vlan can be added to the specified port (0/19/0) successfully
In step 3, the port vlan list can be queried successfully
Remarks
The vlan can be set based on the data provided, attached with this document.
T02-03 Management IP Configuration

T02-0301 Creating an IP Address & Subnetmask
Purpose
To verify the function of creating an ip address and its subnetmask
Network diagram
None
Prerequisite
The vlan has been configured properly (refer to T02-0201)
Procedure
1.
2.
Run the command: interface vlan 1000
3.
Run the command: ip address 10.10.10.10 255.255.255.0
4. Run the command: display interface vlan 1000

Expected results
In step 3, the ip address & subnetmask can be created successfully

Instep 4, the ip address & subnetmask can be queried successfully
Remarks
The ip address can be set based on the data provided, attached with this document.
You can use 10.10.10.10 24 instead of 10.10.10.10 255.255.255.0
T02-0302 Creating a Default Route

Purpose
To verify the function of creating a default static route on the MA5600T

8
OLT MA5600T
Network diagram
None
Prerequisite
The ip address has been configured properly (refer to T02-0301)
Procedure
Expected results
1.
2.
Run the command: ip route-static 0.0.0.0 0.0.0.0 10.10.10.1
3.
Run the command: display ip routing-table
In step 2, the ip route can be created successfully

In step 4, the ip route can be queried successfully
Remarks
The ip address can be set based on the data provided, attached with this document.
T02-04 Ping Reachability

T02-0401 IP Gateway Ping
Purpose
To verify that the connectivity of MA5600T to the gateway is OK
Network diagram
Prerequisite
The ip address & ip route has been configured properly (refer to T02-0302)
Procedure
1.
2.
Run the command: ping [gateway ip-address]
Expected results
The ip address of the gateway can be ping successfully without any losses
Remarks
The ip addresses can be set based on the data provided attached with this document.
T02-0402 IP NMS Ping

Purpose
To verify that the connectivity of MA5600T to the NMS is OK

9
OLT MA5600T
Network diagram
Prerequisite
The ip addresses & ip route has been configured properly (refer to T02-0302)
Procedure
1.
2.
Run the command: ping [nms ip-address]
Expected results
The ip address of the nms can be ping successfully without any losses
Remarks
The ip addresses can be set based on the data provided attached with this document.
T02-05 Saving the Configuration

Purpose
To verify that the configuration data can be sored in the MA5600T system
Network diagram
None
Prerequisite
The configuration is exist
Procedure
Expected results
1.
2.
Run the command: save
3.
Run the command: reboot system
The configuration data can be saved successfully

The data will still exist after the system is switched off or rebooted.
Remarks
T03 Reliability Test

T03-01 Switchover Test
10
OLT MA5600T
T03-0101 Active/Standby Switchover of Control Boards

Purpose
To verify the function of the active/standby switchover by removing/inserting the active

control board
Network diagram
None
Prerequisite
1.
The MA5600T must be configured with the active and standby control boards. The
active control board resides in slot 0/9, and the standby control board resides in slot
0/10. In addition, the MA5600T must be powered on, and must work in the normal
state.
2.
You must be logged in to the MA5600T from a PC through a serial port

(HyperTerminal), a network port (Telnet), or the U2000. Ensure that the MA5600T
can be maintained normally.
1.
Enter the global config mode.
2.
Run the display data sync state command to query the status of data
Procedure
synchronization between the active and standby control boards.

3.
When the data synchronization is complete, remove the active control board.
4.
Check the following information:

(1) Run the display board command to query the board information, and
check whether the original standby control board in slot 0/10 functions as
the active control board.
(2) Check whether the data is lost or modified after the switchover.
huawei>display board 0
Command:
display board 0
------------------------------------------------------------------------SlotID BoardName Status
SubType0 SubType1 Online/Offline
------------------------------------------------------------------------0
H801BIUA Failed
CKMA
Offline
1
2
3
4
5
6
7
8
9
H801SCUN standby_normal
10
H801SCUN Active_normal
11
12
13
14
15
16
17
18
11
OLT MA5600T

19
H801GICE Normal
20
H801GICE Normal
21
22
------------------------------------------------------------------------huawei(config)# display data sync state
All of configuration data (such as data originated from user configuration)
synchronizes completely
All of basic operation data (such as device status data, operation log and
alarm, etc.) synchronizes completely
All of dynamic service data (data realtimely changing such as PSTN call data and
PPPOE call data,etc.) synchronizes completely.
User configuration data CRC check values of active and standby boards are
consistent
(3) Check whether services are in the normal state.

Expected results
When the data synchronization is complete, the active/standby switchover caused by

removing/inserting the active control board should not result in loss or modification of
data. The MA5600T can be maintained and services are in normal state after the
switchover.
Remarks
In step 3, if the data is not synchronized, run the duplicate command to duplicate the
data from the active control board to the standby control board. This ensures that the
data on the standby control board is consistent with the data on the active control board.
T03-0102 Backup Protection of Power Boards

Purpose
To verify the function of the protection switchover by removing/inserting one of power

board.
Network diagram
None
Prerequisite
The MA5600T must be configured with the active and standby power boards. The
power boards reside in slot 0/21, and 0/22. In addition, the MA5600T must be powered
on, and must work in the normal state.
You must be logged in to the MA5600T from a PC through a serial port
(HyperTerminal), a network port (Telnet), or the U2000. Ensure that the MA5600T can
be maintained normally.
Procedure
Enter the global config mode

Check whether both power boards are in normal state by running the display board
command.
Unplug one power board from the sub-rack.
Plug in the power board to the subrack after testing.
Expected results
In step 3, the power board will be in the failed

12
OLT MA5600T
When one power is plugged out, the system power is still running well, and the
MA5600T is still powered on.
Remarks
T03-02 Uplink Protection Test

T03-0201 Uplink Port 1+1 Backup
Purpose
To verify the function of the upstream port 1+1 backup
Network
diagram
Prerequisite
Procedure
1.
All the devices must be properly connected according to the network diagram. The MA5600T
must work in the normal state.
2.
Upstream ports 0/19/0 and 0/19/1 must be connected to the upper-layer LAN switch through
the optical fibers. Port 0/19/0 must be the active upstream port.
3.
The IP address of the port on the LAN switch connected to the MA5600T must be configured
to xxx.xxx.xxx.xxx.
4.
A PC must be connected to an ONT port. The IP address of the PC must be xxx.xxx.xxx.xxx.
1.
Enter the global config & protect mode on MA5600T.
2.
Run the display protect-group command to query the information about the protection
group.
huawei(config-protect)#display protect-group
{ <cr>|pgid<0,63> }:
Command:
display protect-group
Failure: Protect group does not exist
3.
In the protection group mode, run the protect-group first 0/19/0 second 0/19/1 eth
workmode timedelay enable command to create an upstream protection group.
4.
Run the display protect-group command to query the information about the protection
13
OLT MA5600T
group.
huawei(config-protect)#display protect-group
Command:
display protect-group
----------------------------------------------------------------------Group ID
:0
Admin State : enable

----------------------------------------------------------------------Member
Role
Operation
State
PeerMember
----------------------------------------------------------------------0/19/0
work
none
active
0/19/1
protect
none
standby
none
none
----------------------------------------------------------------------Total : 1
huawei(config-protect)#quit
5.
Display ONT info
huawei(config-if-gpon-0/5)#display ont info

{ portid<0,7> }:0
{all<K>|ontid<0,63> }: all
Command:
Display ont info 0 all
----------------------------------------------------------------------------F/S/P ONT
SN
Control Run
Config Match Protect
ID
flag
state state state side
--------------------------------------------------------------------------------------------------------------------------------------------------------F/S/P ONT-ID Description
--------------------------------------------------------------------------------------------------------------------------------------------------------In port 0/ 1/0 , the total of ONTs are: 0, online: 0
6.
Add an ONT to the devices. Run the service-port vlan command to add service ports,
and run the port vlan command to add the aggregation ports to the VLAN with the same
service port.
huawei(config)#ont-lineprofile gpon profile-id 5

huawei(config-gpon-lineprofile-5)#tcont 1 dba-profile-id 6
huawei(config-gpon-lineprofile-5)#gem add 1 eth tcont 1
huawei(config-gpon-lineprofile-5)#mapping-mode vlan
huawei(config-gpon-lineprofile-5)#gem mapping 5 0 vlan 10
huawei(config-gpon-lineprofile-5)#commit
14
OLT MA5600T
huawei(config-gpon-lineprofile-5)#quit
huawei(config)#ont-srvprofile gpon profile-id 5
huawei(config-gpon-srvprofile-5)#ont-port pots 2 eth 4
huawei(config-gpon-srvprofile-5)#commit
huawei(config-gpon-srvprofile-5)#quit
huawei(config)#interface gpon 0/5
huawei(config-if-gpon-0/5)#ont add 0 sn-auth 0100000001 omci ont-lineprofile-id 15 ontsrvprofile-id 10
{ portid<0,7> }:0
{ all<K>|ontid<0,63> }: all
Command:
----------------------------------------------------------------------------F/S/P ONT
SN
Control Run
ID
flag
----------------------------------------------------------------------------0/ 1/0 0 0100000001 active
offline initial initial no
----------------------------------------------------------------------------F/S/P ONT-ID Description
----------------------------------------------------------------------------0/ 1/0
0 ONT_NO_DESCRIPTION
----------------------------------------------------------------------------In port 0/ 1/0 , the total of ONTs are: 1, online: 0
7.
Ping LAN Switch continuously from PC.
8.
Remove the optical fiber from the current working GE port. After the switching of the
protection group, connect the optical fiber back to the GE port.
Expected
results
1.
In step 7, the PC can communicate with the LAN switch.
2.
In step 8, communication between the PC and the LAN switch is interrupted for a while, and
then the communication recovers.
Remarks
The optical ports in a protect group must be configured with auto-negotiation function.When the
protect group is in the forced mode, the switchover of the protect group does not occur and the
communication is interrupted if the Tx fiber is removed from the working port.
T04 Service Function Test

T04-01 Triple Play Test
T04-0101 Multiple Service Profile
15
OLT MA5600T
Purpose
To verify the OLT support multiple service profile
Network diagram
Prerequisite
Procedure
1.
2.
In the global config mode, run the interface gpon 0/1 command to enter the gpon
interface mode.
In the gpon interface mode, run command ont add 0 0 sn-auth
4857544353BA0409 omci ont-lineprofile-id 1 ont-srvprofile-id 1 to add an ONT
to PON port 0.
Run command :
service-port vlan 792 gpon 0/1/0 ont 0 gemport 792 multi-service user-vlan
792 rx-cttr 6 tx-cttr 6
Expected results
Remarks
1.
In step 3, the OLT can create more than 2 service profiles
2.
The bandwidth of the profile follows the rx-cttr & tx-cttr values
You can run the display service-port all to verify the service-port profile
T04-0102 GPON OLT HSI Service

Purpose
To verify the OLT can deliver the HSI (High Speed Internet) service.
16
OLT MA5600T
Network diagram
Prerequisite
inband management mode or through the network port in the outband management
mode (telnet). Ensure that the MA5600T can be maintained normally.
All the devices must be properly connected according to the network diagram. The
MA5600T and the ONT must work in the normal state. The boards must be
registered successfully.
The ONT must be added to PON port 0/1/0, and must be configured and bound with
a DBA profile.
1.
Procedure
The service virtual ports carrying the data service must be configured.
Configure the HSI data service.
(1)
(2)
Run the ont-lineprofile gpon profile-id profile-id command to create a

GPON line profile.
(3)
In the ONT line profile mode, run the tcont tcont-list dba-profile-id
profile-id command to create a T-CONT.
(4)
Run the gemport add gem-index command to add a GEM port to the
PON port.
(5)
Run the gem mapping command to create mapping between the

GEM port and upstream packets.
(6)
Run the commit command to confirm the configuration and then run
the quit command to quit the ONT line profile mode.
(7)
Run the ont-srvprofile gpon command to enter the ONT service

profile mode.
(8)
In the ONT service profile mode, run the ont-port command to set
the information about the ONT port.
(9)
the quit command to quit the ONT service profile mode.
(10) Run the interface gpon frameid/slotid command to enter the GPON
mode.
(11) Run the ont add portid command to add an ONT.
{ portid<0,7> }:0
{ all<K>|ontid<0,63> }:all
17
OLT MA5600T

Command:
display ont info 0 all
----------------------------------------------------------------------------F/S/P ONT
SN
Control Run
ID
flag
----------------------------------------------------------------------------0/ 1/0 0 0100000001 active
----------------------------------------------------------------------------0/ 1/0
(12) Run the quit command to return to the global config mode.
(13) Run the vlan 792 smart command to create smart VLAN 792.
(14) Run the service-port vlan 792 command to add a service port to
VLAN 792, and bind the network-side VLAN, GEM port, and userside VLAN.
(15) Run the port vlan 792 0/19 0 command to add upstream port 0/19/0
to VLAN 792 so that the upstream port and the service port are in the
same VLAN.
(16) Configure the BRAS. In the BRAS port mode, run the ip address
command to configure the IP address of the port and create a data
service channel.
Expected results
The user can access the HSI (High Speed internet) service normally.
Remarks
All the configuration parameters please follow to the data provided, attached with
this document.
T04-0103 GPON OLT OTT Service

Purpose
To verify the OLT can deliver OTT (TV/Video) service.
18
OLT MA5600T
Network diagram
Prerequisite
a DBA profile.
2.
Procedure
Configure the OTT data service.
(1)
(2)

GPON line profile.
(3)
(4)
PON port.
(5)

(6)
(7)

profile mode.
(8)
(9)
mode.
{ portid<0,7> }:0
19
OLT MA5600T

Command:
Displayont info 0 all
----------------------------------------------------------------------------F/S/P ONT
SN
Control Run
ID
flag
----------------------------------------------------------------------------0/ 1/0 0 0100000001 active
----------------------------------------------------------------------------0/ 1/0
same VLAN.
service channel.
Expected results
The user can watch the TV program service normally.
Remarks
this document.
T04-0104 GPON OLT Voice Service

Purpose
To verify the OLT can deliver the voice service.
20
OLT MA5600T
Network diagram
Prerequisite
a DBA profile.
3.
Procedure
Configure the Voice data service.
(1)
(2)

GPON line profile.
(3)
(4)
PON port.
(5)

(6)
(7)

profile mode.
(8)
(9)
mode.
{ portid<0,7> }:0
21
OLT MA5600T

Command:
----------------------------------------------------------------------------F/S/P ONT
SN
Control Run
ID
flag
----------------------------------------------------------------------------0/ 1/0 0 0100000001 active
----------------------------------------------------------------------------0/ 1/0
same VLAN.
service channel.
Expected results
The user can make or receive a call normally.
Remarks
this document.
22

Atp Procedure

Uploaded by

Copyright:

Available Formats

Atp Procedure

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Atp Procedure

Uploaded by

Copyright:

Available Formats

What is the purpose of the document?

What is the purpose of the document?

What steps are required to configure voice service on the OLT?

What steps are required to configure voice service on the OLT?

OLT MA5600T

Acceptance Test Guide

OLT ACCEPTANCE TEST PROCEDURE

OLT SMT PROJECT - Batch 1

PT. SERPONG MAS TELEMATIKA

Document Prepared by Huawei and Approved by SMT

Huawei Technologies Co., Ltd

Acceptance Test Guide

Acceptance Test Guide

Acceptance Test Guide

Acceptance Test Guide

GPON OLT MA5600T

To check whether the cabinet installation meets the requirements

The cabinet installation must be completed.

Verify the quantity of all racks, equipments, cables & accessories.

In step 1, all the quantity are match with Bill of quantity

In step 9, the sub rack fan modules are running well

10. Racks, Equipments & cables are labeled properly

Acceptance Test Guide

T01-02 Maintenance & Management

To verify the maintenance function of the local serial port

Run some commands.

T01-0202 Outband Telnet Mode

To verify the maintenance function by Telnet session

Run Telnet on the maintenance terminal using hyperterminal or other telnet

Log in, and run some commands.

Acceptance Test Guide

T01-0203 Inband Telnet Mode

To verify the maintenance function by inband telnet session

Log in to the MA5600T (OLT-1) using serial or outband mode.

After succeed logging into OLT-2, run some commands.

T01-03 Board Management Test

Acceptance Test Guide

SubType0 SubType1 online/Offline

T01-0302 Disabling/Enabling a PON Port

Acceptance Test Guide

To verify the function of disabling and enabling a PON port

In step 3, you can confirm that port is online

Optical Module status

Optical Module status

T01-0303 Resetting Boards

Acceptance Test Guide

The MA5600T must work in the normal state.

In step 3, the service board is in the normal state.

In step 4, the active control board will be switched-over to standby board.

In step 5, the control board is in the normal state after reset.

In step 7, the service board is in the normal state after reset.

The OLT configuration doesnt change after board resetting.

Board status is failed when service board is removed.

T01-0304 Rebooting The System

Acceptance Test Guide

To check whether the MA5600T can be rebooted without errors

The MA5600T must work in the normal state.

The MA5600T can be rebooted successfully without no errors

The OLT configuration doesnt change after system rebooting