Getting Started

The Wireless-N Router is a combined wired/wireless network connection device

designed specifically for small business, office, and home office networking
requirements. It complies with the IEEE 802.11n (Draft 2.0) standard. It adopts
MIMO as well as SST technologies. It also works well with other 11b/g and 11n
protocol wireless products. Create instant WiFi hotspots at any location where
you have Internet connection

Adding computers to the Wireless-N Router

Setting up a Wireless Infrastructure Network

Open Network by clicking the Start button

, and then clicking Control Panel.
In the search box, type network, and then, under Network and Sharing Center,
click View network computers and devices.
You should see icons for the computer you added and for the other computers
and devices that are part of the network.

Package Contents
Before you starting to use this router, please check if there's anything missing in
the package, and contact your dealer of purchase to claim for missing items:

1 x Wireless-N Router
1 x Quick installation Guide
1 x Power adapter
1 x RJ-45 Networking Cable

1. Log on to the computer.

2. Open Connect to a Network by right-clicking the network icon (
or
) in
the notification area.
3. Choose the wireless network from the list that appears, and then click
Connect.
4. Type the network security key or passphrase if you are asked to do so, and
then click OK.
You'll see a confirmation message when you are connected to the network.
5. To confirm that you added the computer, do the following:

Wireless - N

For a typical wireless setup at home (as shown above),

Please do the following:
1.You will need broadband Internet access (a ADSL, Cable Modem line into
your home or office).
2.Consult with your ADSL or Cable Modem provider for proper installation of
the modem.
3.Connect the ADSL or Cable modem to the Wireless N Router.
Plug in the Power Adapter to the Wireless-N Router.
4.Adding computers to the Wireless-N Router.

Note : If you don't see icons in the Network folder, then network discovery and
file sharing might be turned off.

For more information:

http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-to-a-network
http://windows.microsoft.com/en-US/windows7/Setting-up-a-wireless-network
http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network

IMPORTANT NOTE
You can reset your Wireless-N Router to default setting by press the
RESET' button on the back side of the Router.
You can use this solution if you forget your password.

REV.1.0RTL

Configuring via Web Browser

Open web browser and type http://192.168.0.1 in the browser's address
box. This number is the default IP address for this device.

Setup Wizard

Setup the Router mode

LAN Settings

After successfully login, the following Router Summary will be displayed on your
web browser:

To Setup the router mode, please follow the following instructions:

Please click Operation Mode located at the web management interface, the
following message will be displayed on your web browser:

Please click TCP/IP SettingsLan Interfaces located at the web

management interface, the following message will be displayed on your web
browser:

The login screen below will appear. Enter the User Name and Password
and click OK to login.
The default User name is admin and the Password is admin,

The setup wizard will guide you to configure access point for first time. Please
follow the setup wizard step by step.
The Wizard will guide you the through following steps. Begin by clicking on
Next.
1. Setup Operation Mode
2. Choose your Time Zone
3. Setup LAN Interface
4. Setup WAN Time Zone
5. Wireless LAN Setting
6. Wireless Security Setting

Gateway
In this mode, the device is supposed to connect to internet via ADSL/Cable
Modem.
Bridge
In this mode, all Ethernet ports and wireless interface are bridged together and
NAT function is disabled. All the WAN related function and firewall are not
supported.
Wireless ISP
In this mode, all Ethernet ports are bridged together and the wireless client will
connect to ISP access point.
Click the Apply Changes button to Change your Router Mode.

IP Address:

Enter the IP address of your Router or reset it in dotteddecimal notation Wireless-N Router (factory default:
192.168.0.1).

Subnet Mask:

An address code that determines the size of the network.

Normally use 255.255.255.0 as the subnet mask.

DHCP Type:

Server, Client or Disable

Note:
1) If you change the IP Address of LAN, you must use the new IP Address to
login the Router.
2) If the new LAN IP Address you set is not in the same subnet, the IP
Address pool of the DHCP server will change accordingly at the same time
while the Virtual Server and DMZ Host will not take effect until they are reconfigured.

Connect to Internet (Gateway)

Please click TCP/IP SettingsWAN Interfaces located at the web management
interface, Following example is for PPPoE WAN setting.

Enter the PPPoE Username and PPPoE Password that ISP provided and
leave the others. (The Service Name can be blank)
Click Apply Changes button to save the settings then reboot the router.
After reboot, your router is now ready for Internet connection.

If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and
DNS setting, select 'STATIC (fixed IP)'.
Enter the IP address / Subnet Mask / Default Gateway / MTU / Primary /
Secondary DNS in dotted-decimalnotation provided by your ISP.

Wireless Base Configuration

Wireless Security Configuration

Please click Wireless -> Basic Setttings located at the web management
interface, the following message will be displayed on your web browser:
You could configure the minimum number of Wireless settings for communication,
such as Network Name (SSID) and Channel. The Access Point can be set simply
with only the minimum setting items..

Please click Wireless-> Security located at the web management interface, the
following message will be displayed on your web browser:

If your ISP provides the DHCP service, please choose 'DHCP Client', and the
Router will automatically get IP parameters from your ISP.
This page displays the WAN IP parameters assigned dynamically by your ISP,
including IP address, Subnet Mask, Default Gateway, etc.
Disable Wireless
Band:
SSID:
Broadcast SSID:

Channel Number

Please click Wireless-> WPS located at the web management interface, the
following message will be displayed on your web browser:

Router Administrator Setup

Factory Default and Settings Backup , Restore

you can establish a wireless connection between wireless adapter and Router using
either Push Button Configuration (PBC) method or PIN method.

You can backup all Setting of this router to a file, so you can make several
copied of router configuration for security reason.
To backup or restore router setting, please follow the following instructions:
Please click click 'Management-> Save/Reload setting' located at the web
management interface, then the following message will be displayed on your
web browser:

Wireless On/Off
Supports 11G/11G/11N mixed modes.

Setup the wireless security and encryption to prevent from unauthorized access and
monitoring. Supports 64/128-bit WEP, WPA, WPA2 encryption methods.

When you finish, click 'Apply Changes'.

Main Service Set Identifier. It's the "name" of your wireless

network.
Select enable to enable the device's SSID to be visible by
wireless clients
This field determines which operating frequency will be
used. The default channel is set to Auto, so the AP will
choose the best channel automatically. It is not necessary to
change the wireless channel unless you notice interference
problems with another nearby access point.

Firmware Upgrade

Change management password

The system software used by this router is called as 'firmware', just like any
applications on your computer, when you replace the old application with a new
one, your computer will be equipped with new function. You can also use this
firmware upgrade function to add new functions to your router, even fix the bugs of
this router.

Default password of Wireless Router is admin, and it's displayed on the login
prompt when accessed from web browser. There's a security risk if you don't change
the default password, since everyone can see it. This is very important when you
have wireless function enabled.

Please click 'Management-> Upgrade Firmware' located at the web management

interface, then the following message will be displayed on your web browser:
Click 'Browse' button first, you'll be prompted to provide the filename of
firmware upgrade file. Please download the latest firmware file from our website,
and use it to upgrade your router.

To change password, please follow the following instructions:

Please click 'Management -> Password' menu on the web management interface,
the following message will be displayed on your web browser:

Disable WPS: Enable / Disable

PIN method: If the new device supports Wi-Fi Protected Setup and the PIN
method, you can add it to the network by PIN.
PBC method: If the wireless adapter supports Wi-Fi Protected Setup and the Push
Button Configuration (PBC)
Step 1: Press the WPS button of the Router directly for 2 - 3seconds
or Click Web management interface 'Start PBC'.
Step 2: Press the WPS button of the Adapter directly for 3 seconds.
Step 3: Wait for a while until the next screen appears.
Click Finish to complete the WPS configuration.

Save Settings

Press 'Save' button, and you'll be prompted to download the

configuration as a file, you can please save it as another filename
for different versions, and keep it in a safe place.

Load Settings

Press 'Browse' to pick a previously-saved configuration file from

your computer, and then click 'Upload' to transfer the
configuration file to router. After the configuration is uploaded, the
router's configuration will be replaced by the file you just uploaded.

Reset Settings

Click this 'Reset' button to remove all settings you made, and
restore the configuration of this router back to factory default
settings

When you finish, click 'Apply Changes'; If you want to keep original password
unchanged, click 'Reset'.
After a firmware upgrade file is selected, click 'Upload' button, and the router will
start firmware upgrade procedure automatically. The procedure may take several
minutes, please be patient.
NOTE: Never interrupt the upgrade procedure by closing the web browser or
physically disconnect your computer from router. If the firmware you uploaded is
corrupt, the firmware upgrade will fail, and you may have to return this router to the
dealer of purchase to ask for help. (Warranty voids if you interrupted the upgrade
procedure).