Elastic Bending Theory

Disclaimer: The information on this page has not been checked by an independent person.
Use this information at your own risk.
BeamClamp
Flexible, no drill or weld range of galvanized

structural connectors
www.beamclamp.com
ROYMECH
Hitachi Display Component
Deflection Yokes, STN/TFT Displays, Inverters

for Backlight & more.
www.Hitachi.com.sg
CAD Applications & Tools
Mech-Q Piping, Ducting & Structural AutoCAD,

LT & IntelliCAD. Free Demo
www.asvic.com.au
Home
Beams Index
Elastic Bending Theory
Introduction.... Superposition.... Nomenclature.... Simple Bending.... Deflection.... Area Moment Method....

Introduction
The stress, strain, dimension, curvature, elasticity, are all related, under certain assumption, by the theory of simple bending. This theory
relates to beam flexure resulting from couples applied to the beam without consideration of the shearing forces.
Superposition Principle
The superposition principle is one of the most important tools for solving beam loading problems allowing simplification of very complicated
design problems..
For beams subjected several loads of different types the resulting shear force, bending moment, slope and deflection can be found at any
location by summing the effects due to each load acting separately to the other loads.
Nomenclature
e = strain
E = Young's Modulus = /e (N/m2)
y = distance of surface from neutral surface (m).
R = Radius of neutral axis (m).
I = Moment of Inertia (m4 - more normally cm4)
Z = section modulus = I/ymax(m3 - more normally cm3)
F = Force (N)
x = Distance along beam
= deflection (m)
= Slope (radians)
= stress (N/m2)
Simple Bending
A straight bar of homogeneous material is subject to only a moment at one end and an equal and opposite moment at the other end...
Assumptions
The beam is symmetrical about Y-Y
The traverse plane sections remain plane and normal to the longitudinal fibres after bending (Beroulli's assumption)
The fixed relationship between stress and strain (Young's Modulus)for the beam material is the same for tension and compression ( = E.e )
Consider two section very close together (AB and CD).
After bending the sections will be at A'B' and C'D' and are no longer parallel. AC will have extended to A'C' and BD will have compressed to
B'D'
The line EF will be located such that it will not change in length. This surface is called neutral surface and its intersection with Z_Z is called
the neutral axis
The development lines of A'B' and C'D' intersect at a point 0 at an angle of radians and the radius of E'F' = R
Let y be the distance(E'G') of any layer H'G' originally parallel to EF..Then
H'G'/E'F' =(R+y) /R = (R+y)/R

And the strain e at layer H'G' =
e = (H'G'- HG) / HG = (H'G'- HG) / EF = [(R+y) - R ] /R = y /R

The accepted relationship between stress and strain is = E.e Therefore
= E.e = E. y /R
/E=y/R
Therefore, for the illustrated example, the tensile stress is directly related to the distance above the neutral axis. The compressive stress is
also directly related to the distance below the neutral axis. Assuming E is the same for compression and tension the relationship is the
same.
As the beam is in static equilibrium and is only subject to moments (no vertical shear forces) the forces across the section (AB) are entirely
longitudinal and the total compressive forces must balance the total tensile forces. The internal couple resulting from the sum of ( .dA .y)
over the whole section must equal the externally applied moment.
This can only be correct if (ya) or (y.z.y) is the moment of area of the section about the neutral axis. This can only be zero if the axis
passes through the centre of gravity (centroid) of the section.
The internal couple resulting from the sum of ( .dA .y) over the whole section must equal the externally applied moment. Therefore the
couple of the force resulting from the stress on each area when totalled over the whole area will equal the applied moment
From the above the following important simple beam bending relationship results
It is clear from above that a simple beam subject to bending generates a maximum stress at the surface furthest away from the neutral
axis. For sections symmetrical about Z-Z the maximum compressive and tensile stress is equal.
max = ymax. M / I
The factor I /ymax is given the name section Modulus (Z) and therefore
max = M / Z
Values of Z are provided in the tables showing the properties of standard steel sections
Deflection of Beams
Below is shown the arc of the neutral axis of a beam subject to bending.
For small angle dy/dx = tan =

The curvature of a beam is identified as d /ds = 1/R
In the figure
is small and x; is practically = s; i.e ds /dx =1
From this simple approximation the following relationships are derived.
Integrating between selected limits.

The deflection between limits is obtained by further integration.
It has been proved ref Shear - Bending that dM/dx = S and dS/dx = -w = d2M /dx
Where S = the shear force M is the moment and w is the distributed load /unit length of beam. therefore
If w is constant or a integratatable function of x then this relationship can be used to arrive at general expressions for S, M, dy/dx, or y by
progressive integrations with a constant of integration being added at each stage. The properties of the supports or fixings may be used to
determine the constants. (x= 0 - simply supported, dx/dy = 0 fixed end etc )
In a similar manner if an expression for the bending moment is known then the slope and deflection can be obtained at any point x by single
and double integration of the relationship and applying suitable constants of integration.
Singularity functions can be used for determining the values when the loading a not simple ref Singularity Functions
Example - Cantilever beam

Consider a cantilever beam (uniform section) with a single concentrated load at the end. At the fixed end x = 0, dy = 0 , dy/dx = 0
From the equilibrium balance ..At the support there is a resisting moment -FL and a vertical upward force F.
At any point x along the beam there is a moment F(x - L) = Mx = EI d 2y /dx 2
Example - Simply supported beam

Consider a simply supported uniform section beam with a single load F at the centre. The beam will be deflect symmetrically about the
centre line with 0 slope (dy/dx) at the centre line. It is convenient to select the origin at the centre line.
Moment Area Method

This is a method of determining the change in slope or the deflection between two points on a beam. It is expressed as two theorems...
Theorem 1
If A and B are two points on a beam the change in angle (radians) between the tangent at A and the tangent at B is equal to the area of the
bending moment diagram between the points divided by the relevant value of EI (the flexural rigidity constant).
Theorem 2
If A and B are two points on a beam the displacement of B relative to the tangent of the beam at A is equal to the moment of the area of the
bending moment diagram between A and B about the ordinate through B divided by the relevant value of EI (the flexural rigidity constant).
Examples ..Two simple examples are provide below to illustrate these theorems
Example 1) Determine the deflection and slope of a cantilever as shown..
The bending moment at A = MA = FL

The area of the bending moment diagram AM = F.L2 /2
The distance to the centroid of the BM diagram from B= xc = 2L/3

The deflection of B = y b = A M.x c /EI = F.L 3 /3EI
The slope at B relative to the tan at A = b =AM /EI = FL2 /2EI
Example 2) Determine the central deflection and end slopes of the simply supported beam as shown..
E = 210 GPa ......I = 834 cm4...... EI = 1,7514. 10 6Nm 2
A1 = 10.1,8.1,8/2 = 16,2kNm
A2 = 10.1,8.2 = 36kNm
A2 = 10.1,8.2 = 36kNm
A1 = 10.1,8.1,8/2 = 16,2kNm
x1 = Centroid of A1 = (2/3).1,8 = 1,2
x2 = Centroid of A2 = 1,8 + 1 = 2,8
x3 = Centroid of A3 = 1,8 + 1 = 2,8
x4 = Centroid of A4 = (2/3).1,8 = 1,2
The slope at A is given by the area of the moment diagram between A and C divided by EI.
A = (A1 + A2) /EI
= (16,2+36).10 3 / (1,7514. 10 6)
= 0,029rads = 1,7 degrees
The deflection at the centre (C) is equal to the deviation of the point A above a line that is tangent to C.
Moments must therefore be taken about the deviation line at A.
C = (AM.xM) /EI
= (A1 x1 +A2 x2) / EI = 120,24.10 3/ (1,7514. 10 6)

= 0,0686m = 68,6mm
Sites Providing Relevant Information
Ads by Google
1. Beams, strain, stress , deflections...U of Washington . PDF download with

lots of useful information
2. Pure Bending...Mississipi State U. Pure Bending Lecture Notes.. very useful
3. Review of Simple beam theory...MIT Powerpoint presentation..
4. Lecture Notes for structural Design...U of Toronto - Lots of useful notes on
beam theory and design
This page is being developed

Home
Beams Index
Please Send Comments to [email protected]
Last Updated 17/10/2006
Concrete Beams
S Beam Load Cell
Force Transducer
Steel Beam
Shackle Load Pin

Elastic Bending Theory

Uploaded by

Copyright:

Available Formats

Elastic Bending Theory

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Elastic Bending Theory

Uploaded by

Copyright:

Available Formats

What are the assumptions of simple beam theory?

What are the assumptions of simple beam theory?

How does bending stress vary across the cross-section of a beam?

How does bending stress vary across the cross-section of a beam?

Disclaimer: The information on this page has not been checked by an independent person.

Use this information at your own risk.

Flexible, no drill or weld range of galvanized

Deflection Yokes, STN/TFT Displays, Inverters

CAD Applications & Tools

Mech-Q Piping, Ducting & Structural AutoCAD,

Elastic Bending Theory

Introduction.... Superposition.... Nomenclature.... Simple Bending.... Deflection.... Area Moment Method....

Let y be the distance(E'G') of any layer H'G' originally parallel to EF..Then

H'G'/E'F' =(R+y) /R = (R+y)/R

e = (H'G'- HG) / HG = (H'G'- HG) / EF = [(R+y) - R ] /R = y /R

For small angle dy/dx = tan =

is small and x; is practically = s; i.e ds /dx =1

From this simple approximation the following relationships are derived.

Integrating between selected limits.

Example - Cantilever beam

Example - Simply supported beam

Moment Area Method

The bending moment at A = MA = FL

The distance to the centroid of the BM diagram from B= xc = 2L/3

The slope at B relative to the tan at A = b =AM /EI = FL2 /2EI

E = 210 GPa ......I = 834 cm4...... EI = 1,7514. 10 6Nm 2

A = (A1 + A2) /EI

= (A1 x1 +A2 x2) / EI = 120,24.10 3/ (1,7514. 10 6)

Sites Providing Relevant Information

1. Beams, strain, stress , deflections...U of Washington . PDF download with

This page is being developed

You might also like