En 300 00

LINKWORLD DISTRIBUTORS
Import/Export 2 Africa
Contact Us - Sales and Support

To contact us, please use one of the following numbers
Phone (Monday to Friday from 7:30am until 4:30pm GMT +2)

+27 12 6634331/4 (support)
+27 12 6635571 (sales)
+27 12 6635515 (sales)
Fax
+27 12 6634224
Website
www.linkworld.co.za
E-mail
[email protected]
[email protected]
Feedback on products or services

Any feedback is appreciated on our products and our service. [email protected] Manager of LinkWorld
Technical support on products

Feel free to consult with our personnel.
Address
32 Kersieboom Crescent
Swartkop Ext 4
Centurion
South Africa
0046
SHENZHEN LCS CERTIFICATION SERVICES INC. Report No.LCS080521578S
ETSI EN 300 086 V1.2.1: 2001
TEST REPORT
for
Shenzhen Ledmate Technologies Co., Ltd.
REPEATER
Model No.: TE-9101, TE-9102, TE-9001, TE-9002, TE-4101, TE-4102,
TE-4103, TE-4102, TE-2011, TE-2201, TE-1800
Prepared for : Shenzhen Ledmate Technologies Co., Ltd.

Address : Building A, Second Henglang Industry Park, Longhua Town,
Shenzhen, Guangdong, China
Prepared by : SHENZHEN LCS CERTIFICATION SERVICES INC.

Address : 12/F., Tower A, Pengdou Building, Nanhai Road, Nanshan
District, Shenzhen, Guangdong, China
Report Number : LCS080521578S

Date of Test : November 17, 2007
Date of Report : November 29, 2007
Page 1 of 27
SHENZHEN LCS CERTIFICATION SERVICES INC. Report No. LCS080521578S
TABLE OF CONTENTS
1. TEST RESULT CERTIFICATION............................................................................................. 3
2. EUT DESCRIPTION .................................................................................................................... 4
3. TEST METHODOLOGY ............................................................................................................. 5

1. GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................................... 5
3.1 MEASUREMENT EQUIPMENT USED............................................................................................. 5
3.2 DESCRIPTION OF TEST MODES ............................................................................................... 5
4. FACILITIES AND ACCREDITATIONS ................................................................................... 6

4.1 FACILITIES ....................................................................................................................................... 6
4.2 EQUIPMENT ..................................................................................................................................... 6
4.3 LABORATORY ACCREDITATIONS AND LISTINGS .......................................................... 6
5. SETUP OF EQUIPMENT UNDER TEST .................................................................................. 7

5.1 SETUP CONFIGURATION OF EUT ........................................................................................... 7
6. ETSI EN 300 086 REQUIREMENTS .......................................................................................... 8

6.1 EFFECTIVE RADIATED POWER ............................................................................................... 8
6.2 PEAK POWER DENSITY ............................................................................................................ 12
6.3 FREQUENCY RANGE.................................................................................................................. 14
6.4 TRANSIMITTER SPURIOUS EMISSIONS.............................................................................. 16
6.5 RECEIVER SPURIOUS EMISSIONS ........................................................................................ 23
Page 2 of 27
1. TEST RESULT CERTIFICATION
Applicant : Shenzhen Ledmate Technologies Co., Ltd.

Manufacturer : Shenzhen Ledmate Technologies Co., Ltd.
EUT : REPEATER
Model No. : TE-9101, TE-9102, TE-9001, TE-9002, TE-4101, TE-4102,
TE-4103, TE-4102, TE-2011, TE-2201, TE-1800
Input Voltage : DC 5.0V switch power adapter
Measurement Procedure Used:
APPLICABLE STANDARDS
STANDARD TEST RESULT
ETSI EN 300 086 V1.2.1: 2001 No non-compliance noted
The device described above is tested by SHENZHEN LCS CERTIFICATION SERVICES INC. to
determine the maximum emission levels emanating from the device and the severe levels of the
device can endure and its performance criterion. The measurement results are contained in this
test report and SHENZHEN LCS CERTIFICATION SERVICES INC. is assumed full of
responsibility for the accuracy and completeness of these measurements. Also, this report shows
that the EUT (Equipment Under Test) is technically compliant with the ETSI EN 300 086 V1.2.1:
2003 requirements.
This report applies to above tested sample only and shall not be reproduced in part without
written approval of SHENZHEN LCS CERTIFICATION SERVICES INC.
Date of Test : November 17, 2007
Prepared by :
(Engineer)
Reviewed by :
(Project Manager)
Page 3 of 27
2. EUT DESCRIPTION
Power Supply 5Vdc
Uplink：890－915MHz Downlink ：935－

Operating Frequency
960MHz
Transmit Power 1 mW Max.
Modulation Technique AFK
Number of Channels 1
Operating Mode Point-to-Point

Antenna Type A permanent fixed antenna, which is built-In, designed
as an indispensable part of the EUT.
Note: for more details, please refer to the User’s manual of the EUT.
Page 4 of 27
3. TEST METHODOLOGY
3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS
According to its specifications, the EUT must comply with the requirements of the following
standards:
ETSI EN 300 086 – Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission systems; Data transmission equipment operating in the 2.4GHz ISM
band and using spread spectrum modulation techniques: Part 2: Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive.
3.2 MEASUREMENT EQUIPMENT USED

Name of Calibration
Manufacturer Model Serial Number
Equipment Due
Spectrum Analyzer Agilent E4446A US44300399 05/29/2008
EMI Test Receiver R&S ESCI 1166.595K03 05/29/2008
Pre-Amplifier MITEQ N/A AFS42-00102650-42-10P-42 05/29/2008
Bilog Antenna SCHWAZBECK CBL6143 5082 05/29/2008
Turn Table EMCO 2081-1.21 N/A N.C.R
Antenna Tower CT N/A N/A N.C.R
Controller CT N/A N/A N.C.R
RF Comm. Test set HP 8920B US36142090 N.C.R
Site NSA C&C N/A N/A 05/29/2008
Horn Antenna TRC N/A N/A 05/29/2008
Remark: Each piece of equipment is scheduled for calibration once a year.
3.3 DESCRIPTION OF TEST MODES

The EUT has been tested under its typical operating condition.
Pre-defined engineering program for regulatory testing used to control the EUT for staying in
continuous transmitting and receiving mode is programmed.
Page 5 of 27
4. FACILITIES AND ACCREDITATIONS

4.1 FACILITIES
All measurement facilities used to collect the measurement data are located at
Bldg 69, Majialong Industry Zone District, Nanshan District, Shenzhen, China
The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and
CISPR Publication 22.
4.2 EQUIPMENT
Radiated emissions are measured with one or more of the following types of linearly polarized
antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum
analyzers with preselectors and quasi-peak detectors are used to perform radiated measurements.
Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test
Receivers.
Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for
making measurements.
All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring
Apparatus and Measurement Methods.”
4.3 LABORATORY ACCREDITATIONS AND LISTINGS

Site Description
EMC Lab. : Accredited by TUV Rheinland Guangzhou, 2005.1
The certificate is valid until 2008.2
Accredited by FCC, July 07, 2005

The Certificate Registration Number is 709623.
Accredited by Industry Canada, August 30, 2005

The Certificate Registration Number is 46405-4480
Page 6 of 27
5. SETUP OF EQUIPMENT UNDER TEST

5.1 SETUP CONFIGURATION OF EUT
See test photographs attached in Appendix 1 for the actual connections between EUT and
support equipment.
6. ALL THE EQUIPMENT/CABLES WERE PLACED IN THE

WORST-CASE CONFIGURATION TO MAXIMIZE THE
EMISSION DURING THE TEST.
7. GROUNDING WAS ESTABLISHED IN ACCORDANCE WITH
THE MANUFACTURER’S REQUIREMENTS AND
CONDITIONS FOR THE INTENDED USE.
Page 7 of 27
8. ETSI EN 300 086 REQUIREMENTS

8.1 EFFECTIVE RADIATED POWER
LIMIT
EN 300 086 Clause 4.3.1
Radiated Power <= 100 mW (20 dBm) EIRP over Normal and Extreme conditions.
EN 300 086 Clause 5.7.2
Peak Power <= (20 dBm + 3 dB [including Antenna Assembly Gain in dBi]) over Normal and
Extreme conditions.
Remark: For consistency in documenting the average and peak measurement results, the Peak
Power Limit is reported as 23 dBm and the Antenna Assembly Gain is added to the
measurement.
MEASUREMENT EQUIPMENT USED

Name of Equipment Manufacturer Model Serial Number Calibration Due
Temp. / Humidity Chamber Kingson THS-M1 242 05/26/2008
Test Configuration
Temperature and Voltage Measurement (under normal and extreme test conditions)
Oscilloscope
Monopole
Detector
Antenna
EUT
Splitter
Temperature Chamber
Variable AC Power Supply
Power meter
Remartks:
The spectrum analyzer could be connected to a monopole antenna or directly
connected to the EUT, if the EUT has already employing an antenna connector.
Page 8 of 27
TEST PROCEDURE
1. Please refer to ETSI EN 300 086 (V1.2.1) clause 5.1 for the test conditions.
2. Please refer to ETSI EN 300 086 (V1.2.1) clause 5.7.2.2 for the measurement method.
Page 9 of 27
TEST RESULTS
Operation Mode: 802.11b Test Date: November 17, 207

Temperature: 25oC Tested by: Terry
Humidity: 55 % RH Polarity: Ver. / Hor.
Duty Cycle measurement X: (Ton/Ton + Toff) = 0.99

10 * log (1/x) = 0.04dB
Antenna Assembly Gain: -0.92dBi
Cable Loss= 3.0dB
TRANSMITTER POWER (dBm)
TEST CONDITIONS
Temp (25)°C Temp (0)°C Temp (55)°C
VOL
CHANNEL 230v 207v 253v 207v 253v
POWER
Measured
9.53 11.05 11.05 8.50 8.51
2402 Power
EIRP 11.65 13.17 13.17 10.62 10.63
Measured
9.66 11.23 11.24 8.68 8.67
2441 Power
EIRP 11.78 13.35 13.36 10.80 10.79
Measured
10.17 11.76 11.76 8.98 8.98
2480 Power
EIRP 12.29 13.88 13.88 11.10 11.10
Limit Average Limit= 20 dBm
Measurement uncertainty + 0.28dB / - 0.30dB
(* Operation will be shut-off while the Vmin is lower than 3.4V, and the 3.4V is used as the bottom voltage threshold for the testes)
Remarks:
Steps for determining the ERP/EIRP
1. Substitution method: pseudo-EUT is consisted by an appropriated antenna (chosen among the frequency range:
Conic antenna for 25MHz to 300MHz ; Dipole antenna for 300MHz to 1000MHz and 1GHz to 18GHz) and
signal generator (with a pre-defined in strength signal fed).
2. The pseudo-EUT is then placed at the center of the turntable about 1.5m in height where the location EUT to be
tested.
3. Receiver is placed 3m away from the pseudo-EUT while measuring the strength below 1GHz. For the strength
above 1GHz, the distance between the pseudo-EUT and the receiver varies with the size of the EUT.
4. Receiving antenna will be risen from 1m to 4m measuring the emission level of the pseudo-EUT per each
azithum with horizontal or vertical antenna polarization.
5. The difference between the signal generator and the receiver, by taking all the factor (antenna factor, cable lose
and free space loss etc.) into account and yield the value for the product of the evaluation.
6. By substitute the product and yield the ERP or EIRP at the EUT’s antenna.
Page 10 of 27
Operation Mode: 802.11g Test Date: November 17, 207

Duty Cycle measurement X: (Ton/Ton + Toff) = 0.99

10 * log (1/x) = 0.04dB
Antenna Assembly Gain: -0.92dBi
Cable Loss= 3.0dB
TRANSMITTER POWER (dBm)
TEST CONDITIONS
Temp (25)°C Temp (0)°C Temp (55)°C
VOL
CHANNEL 230v 207v 253v 207v 253v
POWER
Measured
11.35 13.03 13.04 9.07 9.07
2402 Power
EIRP 13.47 15.15 15.16 11.19 11.19
Measured
11.37 13.20 13.21 8.85 8.84
2441 Power
EIRP 13.49 15.32 15.33 10.97 10.96
Measured
11.16 13.14 13.13 8.33 8.34
2480 Power
EIRP 13.28 15.26 15.26 10.45 10.46
Limit Average Limit= 20 dBm
Measurement uncertainty + 0.28dB / - 0.30dB
(* Operation will be shut-off while the Vmin is lower than 3.4V, and the 3.4V is used as the bottom voltage threshold for the testes)
Remarks:
Steps for determining the ERP/EIRP
7. Substitution method: pseudo-EUT is consisted by an appropriated antenna (chosen among the frequency range:
Conic antenna for 25MHz to 300MHz ; Dipole antenna for 300MHz to 1000MHz and 1GHz to 18GHz) and
signal generator (with a pre-defined in strength signal fed).
8. The pseudo-EUT is then placed at the center of the turntable about 1.5m in height where the location EUT to be
tested.
9. Receiver is placed 3m away from the pseudo-EUT while measuring the strength below 1GHz. For the strength
above 1GHz, the distance between the pseudo-EUT and the receiver varies with the size of the EUT.
10. Receiving antenna will be risen from 1m to 4m measuring the emission level of the pseudo-EUT per each
azithum with horizontal or vertical antenna polarization.
11. The difference between the signal generator and the receiver, by taking all the factor (antenna factor, cable lose
and free space loss etc.) into account and yield the value for the product of the evaluation.
12. By substitute the product and yield the ERP or EIRP at the EUT’s antenna.
Page 11 of 27
8.2 PEAK POWER DENSITY
LIMIT
ETSI EN 300 086 clause 4.3.2.2
For equipment using FHSS modulation, the maximum spectral power density shall be limited
to –10dBW (100mW) per 100kHz e.i.r.p. For equipment using other types of modulation, the
maximum power density shall be limited to –20dBW (10mW) per MHz e.i.r.p.

Test Configuration
3 2 MAIN
5
230VAC
Legend
1. Wooden table
2. Test cable
3. Spectrum analyzer
4. EUT
5. Bias-tee
TEST PROCEDURE
2. Please refer to ETSI EN 300 086 (V1.2.1) clause 5.7.3 for the measurement method.
Page 12 of 27
TEST RESULTS
o
Temperature: 25 C Tested by: Terry
TEST Measured Power Antenna 10*log (1/x) Cable loss Measured Power Density
CONDITION Density Reading(A) Gain (B) (C) (D) Result (A+B+C+D)
Ch 0
dBm/MHz
4.49 6.57
Measured Ch 39
dBm/MHz
4.46 -0.92 3.00 -2.10 6.54
Power
Density Ch 79
4.41 6.49
dBm/MHz
Remarks:
Steps for determining the Peak Power Density
1. Remove the EUT’s antenna and the directly connected to the spectrum analyzer with appropriate cable with
connector and attenuator/DC block.
2. Observation is made under the continue operation by the PEAK detector mode, by taking all the factor into
account and yield the Peak Power Density.

o
TEST Measured Power Antenna 10*log (1/x) Cable loss Measured Power Density
CONDITION Density Reading(A) Gain (B) (C) (D) Result (A+B+C+D)
Ch 0
dBm/MHz
2.27 4.35
Measured Ch 39
dBm/MHz
2.33 -0.92 3.00 -2.10 4.41
Power
Density Ch 79
2.15 4.23
dBm/MHz
Remarks:
Steps for determining the Peak Power Density
1. Remove the EUT’s antenna and the directly connected to the spectrum analyzer with appropriate cable with
connector and attenuator/DC block.
2. Observation is made under the continue operation by the PEAK detector mode, by taking all the factor into
account and yield the Peak Power Density.
Page 13 of 27
8.3 FREQUENCY RANGE
LIMIT
ETSI EN 300 086 clause 4.3.3.2
For all equipment the frequency shall lie within the band 2.4GHz to 2.4835GHz (fL>2.4GHz and
fH<2.4835GHz)

Test Configuration
Temperature and Voltage Measurement (under normal and extreme test conditions)
Temperature Chamber
Monopole
Antenna
EUT
(See Note)
Spectrum Analyzer
Variable AC Power Supply
Remarks:
The spectrum analyzer could be connected to a monopole antenna or directly connected to the
EUT, if the EUT has already employing an antenna connector.
TEST PROCEDURE
2. Please refer to ETSI EN 300 086 (V1.2.1) clause 5.7.4 for the measurement method.
Page 14 of 27
TEST RESULTS
o
Frequency Range
TEST CONDITION
Low Frequency High Frequecy
Temp. Voltage MHz MHz
25 °C Vnor 230v 2402.56 2481.35
Vmin 253v 2402.12 2481.72
0 °C
Vmax 207v 2402.13 2481.73
Vmin 253v 2402.85 2480.89
55 °C
Vmax 207v 2402.89 2480.88
Measured frequencies
2402.12 2481.73
(lowest and Highest)
Limit FL > 2400MHz FH < 24835MHz

Frequency Range
TEST CONDITION
Low Frequency High Frequecy
Temp. Voltage MHz MHz
25 °C Vnor 230.00 2402.78 2481.33
Vmin 207.00 2402.56 2482.02
0 °C
Vmax 253.00 2402.52 2482.13
Vmin 207.00 2402.90 2480.98
55 °C
Vmax 253.00 2402.88 2480.92
Measured frequencies
2402.52 2482.13
(lowest and Highest)
Limit FL > 2400MHz FH < 24835MHz
Page 15 of 27
8.4 TRANSIMITTER SPURIOUS EMISSIONS
LIMIT
Spurious emissions are emissions outside the frequency range(s) of the equipment as defined in
Clause 5.2.3.
The level of spurious emissions shall be measured as, either:
1. Their power in specified load (conducted spurious emissions); and
2. Their effective radiated power when radiated by the cabinet or structure of the
equipment (cabinet radiation); or
3. Their effective radiated power when radiated by cabinet and antenna.
The spurious emissions of the transmitter shall not exceed the values in tables in the indicated
bands:
Transmitter limits for NARROWBAND spurious emissions
Frequency Range Limit when operating Limit when in stand-by
30 MHz to 1 GHz -36 dBm -57 dBm
Above 1 GHz to 12.75 GHz -30 dBm -47 dBm

1.8 GHz to 1.9GHz
-47 dBm -47 dBm
5.15 GHz to 5.3GHz
Transmitter limits for WIDEBAND spurious emissions

Frequency Range Limit when operating Limit when in stand-by
30 MHz to 1 GHz -86 dBm -107 dBm
Above 1 GHz to 12.75 GHz -80 dBm -97 dBm

1.8 GHz to 1.9GHz
-97 dBm -97 dBm
5.15 GHz to 5.3GHz
Page 16 of 27

RF CHAMBER II
EMI Test Receiver R&S ESCI 1166.595K03 01/13/2008
AFS42-00102650-
Pre-Amplifier MITEQ N/A 42-10P-42
02/14/2008
Bilog Antenna SCHWAZBECK CBL6143 5082 06/09/2008

Turn Table EMCO 2081-1.21 N/A N.C.R
Antenna Tower CT N/A N/A N.C.R
Controller CT N/A N/A N.C.R
RF Comm. Test set HP 8920B US36142090 N.C.R
Site NSA C&C N/A N/A 09/06/2008
Horn Antenna TRC N/A N/A 03/04/2008
Test Configuration
Below 1GHz
Antenna
tower
10m Bi-log or Loop

antenna
EUT
4m
Spectrum
analyzer
Turntable 1m
1.5m
Reference ground plane
Page 17 of 27
Above 1GHz
Antenna
tower
10m Horn
antenna
EUT
4m
Spectrum
analyzer
Turntable 1m
1.5m
Pre-amp
TEST PROCEDURE
2. Please refer to ETSI EN 300 086 (V1.2.1) clause 5.7.5 for the measurement methods.
Page 18 of 27
TEST RESULTS
Below 1GHz
Test Mode: Gamepad (CH Low) Tested by: Terry
Ambient temperature: 25oC Relative humidity: 55 % RH Date: November 17, 2007
Reading Emission
Frequency Antenna S.G. Cable loss Ant.Gain Limit Margin
level level
(MHz) Polarization (dBm) (dB) (dBi) (dBm) (dB)
(dBuV) (dBm)
57.45 31.17 V -73.63 1.09 -1.97 -76.69 -36.00 -40.69
287.85 45.50 V -54.15 1.84 -10.03 -66.03 -36.00 -30.03
325.67 42.84 V -56.00 1.94 -9.63 -67.57 -36.00 -31.57
455.17 42.17 V -52.08 2.23 -9.75 -64.05 -36.00 -28.05
455.17 45.50 V -48.75 2.23 -9.75 -60.72 -36.00 -24.72
575.33 36.50 V -55.79 2.49 -9.83 -68.11 -36.00 -32.11
287.85 45.00 H -55.32 1.84 -10.03 -67.20 -36.00 -31.20

300.00 40.34 H -58.49 1.88 -9.61 -69.98 -36.00 -33.98
366.50 38.00 H -60.95 2.03 -9.68 -72.66 -36.00 -36.66
455.17 41.84 H -52.28 2.23 -9.75 -64.26 -36.00 -28.26
498.33 35.34 H -59.29 2.33 -9.79 -71.40 -36.00 -35.40
575.33 37.34 H -55.70 2.49 -9.83 -68.02 -36.00 -32.02
Test Mode: Gamepad (CH High) Tested by: Terry

Reading Emission
level level
(dBuV) (dBm)
83.55 43.17 V -68.23 1.20 -3.44 -72.88 -36.00 -36.88
259.95 42.17 V -57.68 1.77 -10.00 -69.45 -36.00 -33.45
287.85 45.50 V -54.15 1.84 -10.03 -66.03 -36.00 -30.03
324.50 42.00 V -56.91 1.93 -9.63 -68.47 -36.00 -32.47
455.17 45.17 V -49.08 2.23 -9.75 -61.05 -36.00 -25.05
576.50 36.50 V -55.70 2.49 -9.83 -68.02 -36.00 -32.02
259.95 40.34 H -60.21 1.77 -10.00 -71.98 -36.00 -35.98

287.85 45.50 H -54.82 1.84 -10.03 -66.70 -36.00 -30.70
393.33 37.17 H -60.37 2.08 -9.69 -72.14 -36.00 -36.14
455.17 41.50 H -52.62 2.23 -9.75 -64.60 -36.00 -28.60
576.50 36.00 H -57.04 2.49 -9.83 -69.35 -36.00 -33.35
664.00 35.00 H -55.98 2.65 -9.88 -68.51 -36.00 -32.51
Note:
1. The emission behaviour belongs to narrowband spurious emission.
2. Remark”---“ means that the emission level is too low to be measured
3. Calculation of result is:
Emission Level (dBm) = Reading level (dBm) + Correction Factor (dB)
Page 19 of 27
Test Mode: Console (CH Low) Tested by: Terry

Reading Emission
level level
(dBuV) (dBm)
84.45 42.84 V -68.53 1.20 -3.48 -73.21 -36.00 -37.21
259.95 42.00 V -57.85 1.77 -10.00 -69.62 -36.00 -33.62
287.85 44.17 V -55.48 1.84 -10.03 -67.36 -36.00 -31.36
324.50 42.34 V -56.57 1.93 -9.63 -68.13 -36.00 -32.13
399.17 40.50 V -55.37 2.09 -9.69 -67.15 -36.00 -31.15
455.17 45.34 V -48.91 2.23 -9.75 -60.88 -36.00 -24.88
232.50 40.50 H -59.87 1.71 -9.97 -71.54 -36.00 -35.54

259.95 39.67 H -60.88 1.77 -10.00 -72.65 -36.00 -36.65
287.85 44.67 H -55.65 1.84 -10.03 -67.53 -36.00 -31.53
399.17 38.50 H -58.44 2.09 -9.69 -70.22 -36.00 -34.22
455.17 42.34 H -51.78 2.23 -9.75 -63.76 -36.00 -27.76
575.33 35.84 H -57.20 2.49 -9.83 -69.52 -36.00 -33.52
Test Mode: Console (CH High) Tested by: Terry

Reading Emission
level level
(dBuV) (dBm)
232.95 41.50 V -58.77 1.71 -9.97 -70.44 -36.00 -34.44
259.95 42.50 V -57.35 1.77 -10.00 -69.12 -36.00 -33.12
287.85 44.17 V -55.48 1.84 -10.03 -67.36 -36.00 -31.36
455.17 46.34 V -47.91 2.23 -9.75 -59.88 -36.00 -23.88
576.50 37.84 V -54.36 2.49 -9.83 -66.68 -36.00 -30.68
232.50 40.50 H -59.87 1.71 -9.97 -71.54 -36.00 -35.54

259.95 39.67 H -60.88 1.77 -10.00 -72.65 -36.00 -36.65
287.85 44.84 H -55.48 1.84 -10.03 -67.36 -36.00 -31.36
393.33 37.00 H -60.54 2.08 -9.69 -72.31 -36.00 -36.31
455.17 43.50 H -50.62 2.23 -9.75 -62.60 -36.00 -26.60
576.50 35.84 H -57.20 2.49 -9.83 -69.51 -36.00 -33.51
Remark:
Emission Level (dBm) = S.G. (dBm) - Cable loss (dB) + Ant. Gain (dBi)
Page 20 of 27
Above 1GHz
Reading Emission
level level
(dBuV) (dBm)
2402 40.13 V -22 5.18 9.85 -26.67 20 -46.67
4804 24.1 V -34.46 8.11 10.43 -36.78 -30 -6.78
2402 43.08 H -19.25 5.18 9.85 -23.92 20 -43.92

4804 24.52 H -32.38 8.11 10.43 -34.7 -30 -4.7

Reading Emission
level level
(dBuV) (dBm)
2480 39.54 V -22.51 5.2 9.95 -27.26 20 -47.26
4960 24.83 V -32.42 8.4 9.95 -33.97 -30 -3.97
2480 43.28 H -18.97 5.2 9.95 -23.72 20 -43.72

4960 24.5 H -35.25 8.4 9.95 -36.8 -30 -6.8
Note:
2. Measurements above show only up to 6 Chris Hsiehimum emissions noted, or would be
lesser if no specific emissions from the EUT are recorded (ie: margin>20dB from the
applicable limit) and considered that's already beyond the background noise floor.
Page 21 of 27

Reading Emission
level level
(dBuV) (dBm)
2402 65.11 V 2.98 5.18 9.85 -1.69 20 -21.69
4804 22.64 V -33.84 8.11 10.43 -36.16 -30 -6.16
2402 38.26 H -24.07 5.18 9.85 -28.74 20 -48.74

4804 19.12 H -39.86 8.11 10.43 -42.18 -30 -12.18

Reading Emission
level level
(dBuV) (dBm)
2441 66.46 V 4.41 5.15 9.9 -0.34 20 -20.34
4882 22.7 V -33.79 8.15 10.46 -36.1 -30 -6.1
2441 39.02 H -23.23 5.15 9.9 -27.98 20 -47.98

4882 18.09 H -40.9 8.15 10.46 -43.21 -30 -13.21
Remark:
2. Measurements above show only up to 6 maximum emissions noted, or would be lesser if
no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable
limit) and considered that's already beyond the background noise floor.
Emission Level (dBm) = S.G. (dBm) - Cable loss (dB) + Ant. Gain (dBi)
Page 22 of 27
8.5 RECEIVER SPURIOUS EMISSIONS
LIMIT
The level of spurious emissions shall be measured as, either:
1. Their power in specified load (conducted spurious emissions); and
2. Their effective radiated power when radiated by the cabinet or structure of the
equipment (cabinet radiation); or
3. Their effective radiated power when radiated by cabinet and antenna.
The spurious emissions of the receiver shall not exceed the values in tables in the indicated
bands:
Receiver limits for NARROWBAND spurious emissions
Frequency Range Limit when in stand-by
30 MHz to 1 GHz -57 dBm
Above 1 GHz to 12.75 GHz -47 dBm
Receiver limits for WIDEBAND spurious emissions

Frequency Range Limit when in stand-by
30 MHz to 1 GHz -107 dBm
Above 1 GHz to 12.75 GHz -97 dBm

(Same as section 6.4 in this test report)
Test Configuration
Radiated Spurious Emissions:

(Same as section 6.4 in this test report)
TEST PROCEDURE
2. Please refer to ETSI EN 300 086 (V1.2.1) clause 5.7.6 for the measurement methods.
Page 23 of 27
TEST RESULTS
Below 1GHz
Reading Emission
level level
(dBuV) (dBm)
195.15 40.34 V -67.16 1.63 -3.09 -71.88 -57.00 -14.88
232.95 40.50 V -59.77 1.71 -9.97 -71.44 -57.00 -14.44
258.60 44.50 V -55.34 1.77 -10.00 -67.11 -57.00 -10.11
287.85 44.50 V -55.15 1.84 -10.03 -67.03 -57.00 -10.03
325.67 40.67 V -58.17 1.94 -9.63 -69.74 -57.00 -12.74
455.17 44.84 V -49.41 2.23 -9.75 -61.38 -57.00 -4.38
232.50 39.34 H -61.03 1.71 -9.97 -72.70 -57.00 -15.70
259.95 38.50 H -62.05 1.77 -10.00 -73.82 -57.00 -16.82
287.85 43.34 H -56.98 1.84 -10.03 -68.86 -57.00 -11.86
367.67 39.17 H -59.77 2.03 -9.68 -71.49 -57.00 -14.49
455.17 41.67 H -52.45 2.23 -9.75 -64.43 -57.00 -7.43
575.33 37.50 H -55.54 2.49 -9.83 -67.86 -57.00 -10.86

Reading Emission
level level
(dBuV) (dBm)
195.15 40.17 V -67.33 1.63 -3.09 -72.05 -57.00 -15.05
259.95 43.17 V -56.68 1.77 -10.00 -68.45 -57.00 -11.45
287.85 44.00 V -55.65 1.84 -10.03 -67.53 -57.00 -10.53
324.50 41.17 V -57.74 1.93 -9.63 -69.30 -57.00 -12.30
455.17 44.34 V -49.91 2.23 -9.75 -61.88 -57.00 -4.88
576.50 37.34 V -54.86 2.49 -9.83 -67.18 -57.00 -10.18
259.95 39.67 H -60.88 1.77 -10.00 -72.65 -57.00 -15.65
287.85 45.17 H -55.15 1.84 -10.03 -67.03 -57.00 -10.03
325.67 39.17 H -56.75 1.94 -9.63 -68.33 -57.00 -11.33
393.33 37.34 H -60.20 2.08 -9.69 -71.97 -57.00 -14.97
455.17 41.84 H -52.28 2.23 -9.75 -64.26 -57.00 -7.26
498.33 35.17 H -59.46 2.33 -9.79 -71.57 -57.00 -14.57
Note:
Page 24 of 27

Reading Emission
level level
(dBuV) (dBm)
195.15 40.34 V -67.16 1.63 -3.09 -71.88 -57.00 -14.88
232.95 40.50 V -59.77 1.71 -9.97 -71.44 -57.00 -14.44
258.60 44.50 V -55.34 1.77 -10.00 -67.11 -57.00 -10.11
287.85 44.50 V -55.15 1.84 -10.03 -67.03 -57.00 -10.03
325.67 40.67 V -58.17 1.94 -9.63 -69.74 -57.00 -12.74
455.17 44.84 V -49.41 2.23 -9.75 -61.38 -57.00 -4.38
232.50 39.34 H -61.03 1.71 -9.97 -72.70 -57.00 -15.70
259.95 38.50 H -62.05 1.77 -10.00 -73.82 -57.00 -16.82
287.85 43.34 H -56.98 1.84 -10.03 -68.86 -57.00 -11.86
367.67 39.17 H -59.77 2.03 -9.68 -71.49 -57.00 -14.49
455.17 41.67 H -52.45 2.23 -9.75 -64.43 -57.00 -7.43
575.33 37.50 H -55.54 2.49 -9.83 -67.86 -57.00 -10.86

Reading Emission
level level
(dBuV) (dBm)
195.15 40.17 V -67.33 1.63 -3.09 -72.05 -57.00 -15.05
259.95 43.17 V -56.68 1.77 -10.00 -68.45 -57.00 -11.45
287.85 44.00 V -55.65 1.84 -10.03 -67.53 -57.00 -10.53
324.50 41.17 V -57.74 1.93 -9.63 -69.30 -57.00 -12.30
455.17 44.34 V -49.91 2.23 -9.75 -61.88 -57.00 -4.88
576.50 37.34 V -54.86 2.49 -9.83 -67.18 -57.00 -10.18
259.95 39.67 H -60.88 1.77 -10.00 -72.65 -57.00 -15.65
287.85 45.17 H -55.15 1.84 -10.03 -67.03 -57.00 -10.03
325.67 39.17 H -56.75 1.94 -9.63 -68.33 -57.00 -11.33
393.33 37.34 H -60.20 2.08 -9.69 -71.97 -57.00 -14.97
455.17 41.84 H -52.28 2.23 -9.75 -64.26 -57.00 -7.26
498.33 35.17 H -59.46 2.33 -9.79 -71.57 -57.00 -14.57
Note:
Page 25 of 27
Above 1GHz
Reading Emission
level level
(dBuV) (dBm)
4804 8.5 V -47.98 8.11 10.43 -50.3 -47 -3.3
4804 9.2 H -49.78 8.11 10.43 -52.1 -47 -5.1

o
Ambient temperature: 25 C Relative humidity: 55 % RH Date: November 17, 2007
Reading Emission
level level
(dBuV) (dBm)
4960 9.98 V -47.27 8.4 9.95 -48.82 -47 -1.82
4960 13.24 H -46.95 8.4 9.95 -48.5 -47 -1.5
Note:
Page 26 of 27

Reading Emission
level level
(dBuV) (dBm)
4804 10.57 V -45.91 8.11 10.43 -48.23 -47 -1.23
4804 10.4 H -48.58 8.11 10.43 -50.9 -47 -3.9

Reading Emission
level level
(dBuV) (dBm)
4960 9.27 V -47.98 8.4 9.95 -49.53 -47 -2.53
4960 10.35 H -49.4 8.4 9.95 -50.95 -47 -3.95
Note:
Page 27 of 27

En 300 00

Uploaded by

Copyright:

Available Formats

En 300 00

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

En 300 00

Uploaded by

Copyright:

Available Formats

LINKWORLD DISTRIBUTORS

Contact Us - Sales and Support

Phone (Monday to Friday from 7:30am until 4:30pm GMT +2)

Feedback on products or services

Technical support on products

ETSI EN 300 086 V1.2.1: 2001

Prepared for : Shenzhen Ledmate Technologies Co., Ltd.

Prepared by : SHENZHEN LCS CERTIFICATION SERVICES INC.

Report Number : LCS080521578S

2. EUT DESCRIPTION .................................................................................................................... 4

3. TEST METHODOLOGY ............................................................................................................. 5

4. FACILITIES AND ACCREDITATIONS ................................................................................... 6

5. SETUP OF EQUIPMENT UNDER TEST .................................................................................. 7

6. ETSI EN 300 086 REQUIREMENTS .......................................................................................... 8

1. TEST RESULT CERTIFICATION

Applicant : Shenzhen Ledmate Technologies Co., Ltd.

Measurement Procedure Used:

Date of Test : November 17, 2007

Uplink：890－915MHz Downlink ：935－

Modulation Technique AFK

Operating Mode Point-to-Point

3.2 MEASUREMENT EQUIPMENT USED

Remark: Each piece of equipment is scheduled for calibration once a year.

3.3 DESCRIPTION OF TEST MODES

4. FACILITIES AND ACCREDITATIONS

4.3 LABORATORY ACCREDITATIONS AND LISTINGS

Accredited by FCC, July 07, 2005

Accredited by Industry Canada, August 30, 2005

5. SETUP OF EQUIPMENT UNDER TEST

6. ALL THE EQUIPMENT/CABLES WERE PLACED IN THE

8. ETSI EN 300 086 REQUIREMENTS

MEASUREMENT EQUIPMENT USED

Temp. / Humidity Chamber Kingson THS-M1 242 05/26/2008

Remark: Each piece of equipment is scheduled for calibration once a year.

Variable AC Power Supply

Operation Mode: 802.11b Test Date: November 17, 207

Duty Cycle measurement X: (Ton/Ton + Toff) = 0.99

Operation Mode: 802.11g Test Date: November 17, 207

Duty Cycle measurement X: (Ton/Ton + Toff) = 0.99

8.2 PEAK POWER DENSITY

MEASUREMENT EQUIPMENT USED

Remark: Each piece of equipment is scheduled for calibration once a year.

Operation Mode: 802.11g Test Date: November 17, 207

8.3 FREQUENCY RANGE

MEASUREMENT EQUIPMENT USED

Remark: Each piece of equipment is scheduled for calibration once a year.

Variable AC Power Supply

Operation Mode: 802.11g Test Date: November 17, 207

8.4 TRANSIMITTER SPURIOUS EMISSIONS

Above 1 GHz to 12.75 GHz -30 dBm -47 dBm

Transmitter limits for WIDEBAND spurious emissions

Above 1 GHz to 12.75 GHz -80 dBm -97 dBm

MEASUREMENT EQUIPMENT USED

Bilog Antenna SCHWAZBECK CBL6143 5082 06/09/2008

Remark: Each piece of equipment is scheduled for calibration once a year.

10m Bi-log or Loop

Reference ground plane

287.85 45.00 H -55.32 1.84 -10.03 -67.20 -36.00 -31.20

Test Mode: Gamepad (CH High) Tested by: Terry