Scribd
Upload
847 views2 pages

HDMI Cable Making Guide

(1) The document provides step-by-step instructions for stripping and preparing HDMI cable wires for insertion into an HDMI connector. It details separating the twisted wire pairs, cutting them to the proper length, and arranging them according to a pin assignment diagram. (2) It then explains inserting the arranged wires into plastic holders, compressing them using a special tool, and installing the assembled connector into a metal shell. (3) The final step is to test the completed cable on a DVD or TV system to ensure proper connection and transmission. Proper preparation and use of the designated HDMI cables is emphasized for reliability.

Uploaded by

Anonymous 4P461ST3Ve
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
847 views2 pages

HDMI Cable Making Guide

(1) The document provides step-by-step instructions for stripping and preparing HDMI cable wires for insertion into an HDMI connector. It details separating the twisted wire pairs, cutting them to the proper length, and arranging them according to a pin assignment diagram. (2) It then explains inserting the arranged wires into plastic holders, compressing them using a special tool, and installing the assembled connector into a metal shell. (3) The final step is to test the completed cable on a DVD or TV system to ensure proper connection and transmission. Proper preparation and use of the designated HDMI cables is emphasized for reliability.

Uploaded by

Anonymous 4P461ST3Ve
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

STEP 1: Strip Cable

(1) Strip cable jacket. Cut out braiding and Aluminum foil, only keep drain wire
(2) Strip the Aluminum foil of 5 Twisted Pairs (TP) per illustrated dimensions
Among 5 TPs, four with blue foil are for TMDS data, and one with silver-colored
foil is for Ethernet and Audio Return Channel (HEAC). It is important to keep the
foil length of HEAC pair 6mm for easy installation in the following steps.
(1)

Pin Assignment
Any mis-wiring, even an intercrossing of Twisted Pairs, will lead to transmission failure. So
it is EXTREMELY VITAL to make sure the wire assignment correct without any error !!!

(2)

Pin #

19

17

15

13

11

Twisted Pair
w/silver foil

STEP 2: Insert Wires

16

White

14

Brown

12

Drain

10

Twisted Pair
With brown wire

White

18

Red

Orange

Yellow

White

Green

Drain

of silver TP

Twisted Pair
with green wire
white

Red

Drain

wires

Twisted Pair
with red wire

Blue

Drain

White

Twisted Pair
with blue wire
yellow

Drain

Pin #

White

wires

(1) Arrange the wires for 10-hole holder per the pin assignment in the next
page.
(2) Cut the wires at an angle for easy insertion
(3) Insert the wires into 10-hole holder in one step.
You can divide 10
wires into two groups and insert them in two steps before you are skillful.
(4) Arrange the wires for 9-hole holder and insert the wires into the holder.
(5) It is very IMPORTANT to keep two holders in alignment.

In alignment
http://www.sinotek.net
[email protected]

Patented connector and hand tool, all rights reserved.

HD-901-33 Ver. 3.13

Dec 9, 2009

STEP 3: Compress

STEP 4: Install Shell

(1) Install a connector into the guiding jig (the black piece)
(2) Install and press the holders into the guiding jig.
The 10-hole blue holder is for 10-pin side of HDMI connector and the
9-hole green holder for 9-pin side.
Press two holders with thumb until they lock with the connector
(3) Insert the assembly into the hand tool
(4) Compress the tool
(5) Finished! Excessive wires are cut out automatically.

(1)

(1) Put the connector into the bottom half of the die-cast metal shell.
(2) Install the metal belt to fasten the cable onto the metal shell. Make
sure the drain wire be under the metal belt for grounding.
(3) Install the upper half and two screws to finish the whole procedure.

(3)

STEP 5: Test
(4)
(2)

Test the cable on DVD-TV system, or with a portable tester.

IMPORTANT
IMPORTANT
Please use our specially designed HDMI cables HDFT-24-x & HDFT-26-x only.
Please use our specially designed HDMI cables HDFT-24-x & HDFT-26-x only.

(5)

We have no guarantee that this connector works with the cables other than our
We have no guarantee that this connector works with the cables other than our
cables due to the big differences in conductor gauge, construction, insulation
cables due to the big differences in conductor gauge, construction, insulation
material, thickness, eccentricity ratio, foaming consistence, twisting parameters,
material, thickness, eccentricity ratio, foaming consistence, twisting parameters,
impedance consistence and match Any incompliance of the above is likely to
impedance consistence and match Any incompliance of the above is likely to
result in continuity failure.
result in continuity failure.
Besides this printed brief manual, both a detailed PowerPoint file and a MP4
Besides this printed brief manual, both a detailed PowerPoint file and a MP4
video demo file are available. Please contact your dealer for assistance.
video demo file are available. Please contact your dealer for assistance.

http://www.sinotek.net
[email protected]

Patented connector and hand tool, all rights reserved.

HD-901-33 Ver. 3.13

Dec 9, 2009

You might also like