4.3 Rates of Reactions
4.3 Rates of Reactions
4.3 Rates of Reactions
1.
The kinetics of the hydrolysis of the halogenoalkane RCH2Cl with aqueous sodium hydroxide
(where R is an alkyl group) was studied at 50 C. The following results were obtained:
Experiment
[RCH2Cl]
[OH]
0.050
0.10
4.0 104
0.15
0.10
1.2 103
0.10
0.20
1.6 103
(i)
Deduce the order of reaction with respect to the halogenoalkane, RCH2Cl, and with
respect to the hydroxide ion, OH, giving reasons for your answers.
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
(4)
(ii)
(iii)
Calculate the value of the rate constant with its units for this reaction at 50 C.
(2)
PMT
(iv)
Using your answer to part (ii), write the mechanism for this reaction.
(3)
(Total 10 marks)
2.
(a)
(i)
2SO2(g) + O2(g)
(1)
(ii)
(5)
PMT
(b)
Solid vanadium(V) oxide, V2O5, is an effective catalyst for this reaction. State the effect
of using double the mass of catalyst on:
(i)
(ii)
3.
In an experiment to determine the rate of the reaction between persulphate ions and iodide ions
in aqueous solution
S2O 82 + 2I 2SO 24 + I2
the following data were obtained:
Concentration/mol dm 3
(a)
(i)
Initial rate
/mol dm3 s 1
S2 O 2
8
0.100
0.100
0.36
0.200
0.100
0.72
0.200
0.200
1.44
Deduce the order of reaction with respect to each of the reagents and hence write
the rate equation for the reaction.
............................................................................................................................
............................................................................................................................
............................................................................................................................
(3)
(ii)
With reference to this reaction state what is meant by the overall order of a
3
PMT
reaction.
............................................................................................................................
............................................................................................................................
(1)
(iii)
(2)
(iv)
Explain why the rate equation cannot be written directly from the stoichiometric
equation for the reaction.
............................................................................................................................
............................................................................................................................
(1)
(b)
(i)
Suggest a suitable experimental technique that would enable you to determine the
rate of the reaction given opposite.
............................................................................................................................
............................................................................................................................
(1)
(ii)
PMT
(iii)
4.
(a)
(i)
(ii)
Explain why the order of reaction cannot be deduced from the stoichiometric
equation for a reaction.
.......
.......
.......
(1)
PMT
(b)
Give the mechanism for the SN1 reaction between 2-bromobutane and
hydroxide ions.
(3)
(ii)
(iii)
In an experiment designed to find the mechanism of the reaction between 2-bromo2-methylpropane and hydroxide ions the following data were obtained at constant
temperature.
Initial concentration of
2-bromo-2-methylpropane
/mol dm3
Initial concentration of
OH / mol dm3
0.10
0.10
1.2 102
0.20
0.10
2.4 102
0.30
0.20
3.6 102
PMT
Use the data to deduce the rate equation for the reaction of 2-bromo-2methylpropane with sodium hydroxide solution.
.......
.......
.......
(3)
(c)
Suggest, in outline, a method you could use to follow the progress of the reaction between
a bromoalkane and aqueous sodium hydroxide.
.......
.......
.......
.......
.......
.......
(3)
(Total 14 marks)
5.
(a)
(i)
Show by calculation that the starting concentration of the manganate(VII) ions was
3.03 102 mol dm3.
(1)
PMT
(ii)
3.03 102
400
2.98 102
800
2.86 102
1200
2.75 102
1600
1.90 102
2000
7.50 103
2400
2.50 103
Plot a graph of the concentration of manganate(VII) ions against time and from it
determine the initial rate of the reaction and the rate at 1600 s.
(5)
A second experiment was set up involving the same chemicals in the same concentrations
as in experiment 1 but this time some solid manganese(II) sulphate was dissolved in the
ethanedioic acid before the potassium manganate (VII) solution was poured in. The plot
of the concentration of manganate(VII) ions against time is given below:
3.5 10 2
3.0 10 2
concentration /mol dm 3
(b)
2.5 10 2
2.0 10 2
1.5 10 2
1.0 10 2
5.0 10 3
0
400
PMT
(i)
(ii)
Compare this graph with the one you plotted in (a) (ii) and give two pieces of
evidence that manganese(II) sulphate is a catalyst for this reaction.
(2)
(c)
(i)
(ii)
Describe how aqueous sodium hydroxide solution could be used to show that
manganese(II) ions had been produced in the reaction between manganate (VII)
ions and ethanedioate ions in acidic solution.
(2)
(Total 14 marks)
6.
1
2
O2(g)
(b)
(ii)
The overall order of the reaction is one. Give the rate equation for the reaction.
9
PMT
Rate =
(1)
(iii)
How would you use a graph of hydrogen peroxide concentration against time to
show that the reaction is first order?
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
(2)
(c)
The data in the table show the effect of temperature on the rate of this reaction.
T
/K
Rate
/ mol dm3 s1
1/T
/K1
ln(rate)
293
1.6 106
3.41 103
13.3
302
4.2 106
3.31 103
12.4
314
14.4 106
3.19 103
11.1
323
33.8 106
3.10 103
10.3
10
PMT
(i)
On the axes below, sketch graphs for two temperatures, T1 and T2, where T2 is
greater than T1, and use them to explain why increasing temperature has a dramatic
effect on the rate of this reaction.
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
(4)
11
PMT
(ii)
(3)
12
PMT
(iii)
Use your graph and the equation below to calculate the activation energy, EA, for
this reaction.
ln(rate) = constant
EA
R
(1/T)
You should include the sign and units with your answer which should be given to
two significant figures.
(3)
(Total 16 marks)
7.
(a)
In a rate of reaction experiment between two substances, A and B, the overall order of the
reaction was found to be 2. Write three possible rate equations for such a second order
reaction between A and B.
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
(3)
(b)
At a certain temperature the rate of reaction between nitrogen monoxide, NO, and
hydrogen, H2, was investigated. The following data were obtained.
[NO]/mol dm3
[H2]/mol dm3
Rate/mol dm3 s1
1.0
1.0
0.02
1.0
3.0
0.06
3.0
1.0
0.18
13
PMT
(i)
Use the data above to deduce the rate equation for this reaction.
(3)
(ii)
Use your answer to (b)(i) above to calculate the value of the rate constant, with
units.
(2)
(c)
The investigation described in part (b), above, was repeated, but at a higher temperature,
and the rate of the reactions increased. Explain, in terms of particles, why an increase in
temperature increases the rate of a reaction.
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
(3)
14
PMT
(d)
State the effect of an increase in temperature on the value of the rate constant, k.
...............................................................................................................................
(1)
(e)
8.
15 cm3 of water was mixed with 15 cm3 of ethanol. 1.0 cm3 of 2-bromo-2-methylbutane
was added to this mixture. The conductivity of this mixture was measured and rose from
0 to 200 microsiemens in 600 s.
The experiment was repeated using equal volumes of water and ethanol, with 2.0 cm3 of
2-bromo-2-methylbutane in the 31 cm3 of mixture. The conductivity of the mixture rose
from 0 to 400 microsiemens in 600 s.
(i)
Explain why the conductivity of the mixture increases during these reactions.
..........................................................................................................................
..........................................................................................................................
(1)
(ii)
Why was an ethanol/water mixture used for this reaction rather than water on its
own?
..........................................................................................................................
..........................................................................................................................
(1)
15
PMT
(iii)
What is the effect on the rate of the reaction of doubling the concentration of
2-bromo-2-methylbutane?
..........................................................................................................................
(1)
(iv)
(v)
(b)
The table below shows the results from another experiment where a solution of
2-bromo-2-methylbutane is reacted with varying concentrations of hydroxide ions.
A few drops of an acid-alkali indicator are added to the mixture and the time for the
indicator to change to the acidic colour is measured.
[C5H11Br]
/102 mol dm3
[OH]
/10 mol dm3
Time
/s
1.5
0.75
1.5
1.50
1.5
2.25
14
16
PMT
(i)
Calculate the rate of the reaction, in mol dm3 s1, for each concentration of
hydroxide ions.
(2)
(ii)
What effect does doubling the concentration of hydroxide ions have on the rate of
the reaction?
..........................................................................................................................
(1)
(iii)
What is the order of the reaction with respect to the hydroxide ions?
..........................................................................................................................
(1)
(c)
When 2-bromo-2-methylbutane reacts with water, or hydroxide ions, the mechanism for
the reaction is the same.
(i)
Use your answers to (a)(iv) and (b)(iii) to write the rate equation for the reaction
with hydroxide ions.
Rate =
(1)
17
PMT
(ii)
Write a mechanism for the reaction which is consistent with your rate equation.
(2)
(Total 12 marks)
9.
(i)
Write the ionic equation for the reaction of thiosulphate ions with iodine in
aqueous solution.
.....................................................................................................................................
(2)
(ii)
State which indicator is used in this titration, and describe what you would see at
the end point.
.....................................................................................................................................
.....................................................................................................................................
(2)
18
PMT
(b)
Use the following data to deduce the rate equation for the reaction of propanone with
iodine in acidic solution, given that the order with respect to [H+] is one.
[CH3COCH3]
/mol dm3
[I2]
/mol dm3
Initial rate
/mol dm3 s1
1.0
0.10
3.2 103
1.0
0.20
3.2 103
2.0
0.10
6.4 103
(3)
(c)
(ii)
19
PMT
(d)
What does the rate equation in (b) tell you about the involvement of iodine in the ratedetermining step, and hence about the least number of steps in the reaction?
...............................................................................................................................................
...............................................................................................................................................
...............................................................................................................................................
(2)
(e)
Sodium hydroxide cannot be used to stop the reaction, because very alkaline conditions
cause another reaction to occur between propanone and iodine.
Write the equation for this reaction.
...............................................................................................................................................
(3)
(Total 14 marks)
20
PMT
10.
This question is about the kinetics of the reaction in which ammonium cyanate, NH4CNO, turns
into urea, NH2CONH2, in aqueous solution.
NH4CNO(aq) 2CONH2(aq)
The table below shows the mass of urea, mt, which formed at different times in a solution of
ammonium cyanate of known starting concentration.
When the reaction stopped the mass of urea, mfinal, was 20.3 g.
(a)
Time / min
Mass of urea, mt /g
mfinal mt/g
20.3
25
12.5
7.8
50
15.7
4.6
75
17.1
3.2
100
17.5
2.8
150
18.7
1.6
200
19.1
300
20.0
21
PMT
(b)
Plot a graph of mfinal mt (on the vertical axis) against time (on the horizontal axis).
(2)
22
PMT
(c)
The graph can be used to work out a rate equation for the reaction.
What term in the rate equation for the reaction is proportional to mfinal mt?
.........................................................................................................................
(1)
23
PMT
(d)
(i)
Show THREE successive half-life measurements on your graph, and give their
values.
1. ........................................................... 2. ...........................................................
3. ...........................................................
(2)
24
PMT
(ii)
Use the half-lives to decide whether the reaction is zero order, first order or second
order. Explain how you decided the order.
Order of reaction ..............................................................................................
Explanation .......................................................................................................
..........................................................................................................................
..........................................................................................................................
(2)
25
PMT
(iii)
26
PMT
(e)
A student thought that water might take part in the rate-determining step of the reaction.
(i)
27
PMT
(ii)
The solution of ammonium cyanate used in the experiment initially contained 0.35
moles of ammonium cyanate in approximately 1 dm3 (55.5 moles) of water.
Is the order you calculated in (d)(ii) an order with respect to ammonium cyanate, or
could it include the water as well? Explain your answer.
..........................................................................................................................
..........................................................................................................................
..........................................................................................................................
(2)
(Total 12 marks)
28
PMT
11.
(a)
0.35
0.30
0.25
0.20
[ester] / mol dm3
0.10
0.05
0
0
0.5
1.0
1.5 2.0
Time / hr
2.5
3.0
29
PMT
(i)
Show, under these conditions, that the reaction is first order in methyl ethanoate.
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(2)
30
PMT
(ii)
Explain with a reason whether or not the overall order of reaction must also be one.
.....................................................................................................................................
.....................................................................................................................................
(1)
31
PMT
(iii)
Assuming the reaction is first order, use the graph to calculate the rate constant, k.
Include the units in your answer.
(3)
32
PMT
(iv)
33
PMT
(b)
34
PMT
(ii)
Suppose that these two different values of activation energy were for the same
overall reaction at the same temperature. Suggest a way in which the conditions
are different for the two reactions.
.....................................................................................................................................
.....................................................................................................................................
(1)
(Total 11 marks)
35
PMT
12.
36
PMT
A series of experiments was carried out to investigate the kinetics of this reaction.
Initial concentration of
(CH3)3CBr
/mol dm3
Initial concentration of
NaOH
/mol dm3
5.0 104
2.0 102
1.5 104
1.5 103
2.0 102
4.5 104
1.5 103
4.0 102
4.5 104
/mol dm3 s1
37
PMT
(a)
(i)
(ii)
38
PMT
(b)
Use one set of the data to calculate the rate constant for this reaction. Include the unit of
the rate constant in your answer.
(2)
39
PMT
(c)
40
PMT
Is your rate equation consistent with this information? Explain your answer.
....................................................................................................................................
....................................................................................................................................
....................................................................................................................................
....................................................................................................................................
(1)
41
PMT
(d)
In another series of experiments, the rate of the reaction was measured at different
temperatures. Complete the missing numbers in the table below.
temperature (T)
/K
1/temperature (1/T)
/K1
rate
/mol dm3 s1
ln(rate)
300
3.33 103
3.35 104
8.00
310
3.23 103
7.47 104
7.20
320
3.13 103
1.66 103
6.40
330
3.03 103
4.09 103
5.50
340
2.94 103
9.10 103
4.70
350
1.66 102
(2)
42
PMT
(e)
On the axes below plot a graph of ln(rate) on the vertical axis against 1/T on the
horizontal axis.
(2)
43
PMT
(f)
EA
(1/T)
R
to calculate the value of the activation energy, EA, for the reaction.
[R = 8.31 J K1 mol1].
Show your working clearly and give your answer to 2 significant figures.
(2)
(Total 12 marks)
44
PMT
13.
This question is about the kinetics of the reaction between 2-bromo-2-methylpropane and
sodium hydroxide in a suitable solvent.
(CH3)3CBr + NaOH (CH3)3COH + NaBr
Equal volumes of 0.200 mol dm3 solutions of the two reactants were mixed together and
maintained at a constant temperature of 30 C. The concentration of hydroxide ions was
determined at different times. The results are shown in the table below.
[OH]
/mol dm3
Time
/s
0.100
0.071
120
0.052
240
0.035
360
0.024
480
0.018
600
(a)
Describe how the concentration of hydroxide ions could be determined during the
reaction.
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
(3)
45
PMT
(b)
(i)
Plot a graph of hydroxide ion concentration (vertical axis) against time (horizontal
axis) on the grid below.
(2)
46
PMT
(ii)
Mark on your graph TWO consecutive half-lives. Measure their values and write
them below.
First half-life ..........................................................................................................
Second half-life .....................................................................................................
(1)
(iii)
What is the order of the reaction? Explain how you used your half-lives to arrive at
your answer.
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
(1)
(iv)
(v)
(c)
(i)
47
PMT
(ii)
Write equations to show the steps involved in your chosen mechanism for this
reaction.
(2)
(Total 13 marks)
14.
(a)
(ii)
Rate constant
............................................................................................................................
............................................................................................................................
(1)
(b)
Experiment
[CH3I]
/mol dm3
[OH]
/mol dm3
Initial rate
/mol dm3 s1
0.1
0.1
1 105
0.2
0.1
2 105
0.1
0.2
2 105
48
PMT
(i)
State the order of reaction with respect to CH3I and with respect to OH ions.
Give your reasons.
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
(2)
(ii)
(iii)
Calculate the value of the rate constant for this reaction, stating its units.
(2)
49
PMT
(c)
The reaction
CH3CH2Br + OH CH3CH2OH + Br
has an SN2 mechanism that proceeds through a transition state.
(i)
(3)
(ii)
Draw a reaction profile for this exothermic reaction. Show the energy level of the
transition state on the profile.
(2)
(Total 12 marks)
50
PMT
15.
Persulphate ions, S2O 82 slowly oxidise arsenic(III) acid, H3AsO3 in aqueous solution according
to the equation
S2O 82 + H3AsO3 + H2O 2SO 24 + H3AsO4 + 2H+
25 cm3 of a 1.0 mol dm3 solution of potassium persulphate was mixed with 25 cm3 of a
solution of arsenic(III) acid of the same concentration.
At timed intervals, small potions of the reation mixture were analysed to determine the
concentration of persulphate ion, [S2O 82 ].
The results are shown below.
Time
/ minutes
[ S 2 O 82 ]
/ mol dm3
1.0
0.76
10
0.62
15
0.52
20
0.44
30
0.35
51
PMT
(a)
(i)
On the grid below, plot a graph of the concentration of persulphate ions against
time.
1.0
0.9
[S 2 O 8 2 ]
/ mol dm 3
0.8
0.7
0.6
0.5
0.4
0.3
0
10
15
Time / min
20
25
30
(2)
52
PMT
(ii)
Draw a tangent to the curve at the point where [S2O 82 ] = 0.50 mol dm3 and use it
to calculate the slope of the curve at that point. Give your answer to two significant
figures.
Slope: ..............................
(4)
(b)
The rate of the reaction at a particular concentration of reactant can be measured from the
slope of the graph at that concentration.
The initial rate, which is the rate when the concentrations of persulphate ions, S2O 82 ,
and arsenic(III) acid, H3AsO3, are both 1.0 mol dm3, was found to be 0.060 mol dm
3
min1.
(i)
Use your answer to (a)(ii) to show that the ratio of the initial rate to the rate when
[S2O 82 ] and [H3AsO3] are 0.50 mol dm3 is approximately 4:1. Use this ratio to
deduce the overall order of reaction.
(3)
53
PMT
(ii)
Suggest TWO rate equations that agree with the order of the reaction that you have
deduced in (i). How could the experiment be adapted to distinguish between these
two rate equations?
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
............................................................................................................................
(5)
(Total 14 marks)
16.
(a)
54
PMT
(i)
(ii)
Use the diagram to explain why the rate of a reaction increases with an increase in
temperature.
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
(3)
(iii)
55
PMT
(b)
Describe, with the aid of a diagram, an experiment you could do to follow the
progress of this reaction at different temperatures.
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
(4)
56
PMT
(ii)
Would you expect Ssystem to be positive or negative for this reaction? Justify your
answer with TWO pieces of evidence.
................................................................................................................................
...............................................................................................................................
................................................................................................................................
................................................................................................................................
................................................................................................................................
(2)
(iii)
17.
CH 3
C2H5
C
Br
CH 3
CH 3
+ OH
C2H5
CH 3 + Br
OH
57
PMT
(a)
The rate of reaction can be followed by measuring the concentration of 2-bromo-2methylbutane at various times.
In one such experiment, a known amount of 2-bromo-2-methylbutane was added to a
large excess of aqueous sodium hydroxide. The following results were obtained.
Time/min
0.96
10
0.61
20
0.38
30
0.24
40
0.15
50
0.10
(i)
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
0.10
0.00
0
10
20
30
Time / min
40
50
60
(2)
58
PMT
(ii)
Show TWO successive half-life measurements on your graph and write their values
below.
First half-life
............................................................
Second half-life
............................................................
(2)
(iii)
(b)
(ii)
59
PMT
(iii)
Write a mechanism for the reaction which is consistent with your rate equation.
(3)
(c)
60
PMT
18.
One step in the manufacture of nitric acid is the reaction between nitrogen(II) oxide and oxygen
to form nitrogen(IV) oxide.
2NO(g) + O2(g)
(a)
(i)
2NO2(g)
H = 114 kJ mol1
Use the equation to suggest the sign of Ssystem for the forward reaction. Justify
your answer.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
(ii)
What is the sign of Ssurroundings for the forward reaction? Justify your answer.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
(b)
(i)
Units ..............................................
(2)
61
PMT
(ii)
Suggest how the temperature and pressure could be altered to make nitrogen(IV)
oxide more economically. Justify your suggestions by considering both yield and
rate.
Temperature
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
Pressure
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(4)
(c)
(i)
What property would allow you to follow the progress of this reaction? Justify your
answer.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
62
PMT
(ii)
[NO(g)]
/mol dm3
[O2(g)]
/mol dm3
Initial rate
/mol dm3 s1
1.0 103
1.0 103
8.0 106
2.0 103
1.0 103
3.2 105
2.0 103
2.0 103
6.4 105
What is the order of the reaction with respect to NO(g)? Justify your answer.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
(iii)
(1)
(iv)
63
PMT
(v)
Calculate the rate constant, k, for this reaction. Include units with your answer.
(2)
(d)
Suggest why this reaction takes place quickly at room temperature and pressure.
.....................................................................................................................................
(1)
(Total 20 marks)
19.
(a)
64
PMT
(b)
AB3
Initial
concentration of
B
/ mol dm3
0.100
0.100
0.00200
0.100
0.200
0.00798
0.200
0.100
0.00399
Experiment
(i)
Initial rate of
reaction
State the order of reaction with respect to each of the reactants. Justify your
answer.
Reactant A ........................................................................................................
...........................................................................................................................
...........................................................................................................................
Reactant B ........................................................................................................
...........................................................................................................................
...........................................................................................................................
(3)
(ii)
65
PMT
(iii)
Use the experimental data from Experiment 1 to calculate the rate constant,
including units.
(2)
(iv)
Suggest a possible mechanism for the reaction between A and B, leading to the
formation of AB3. Identify the rate-determining step.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(3)
(c)
The rae constant, k, for the reaction in (b) was measured at different temperatures.
The following data were obtained.
log10 k
1 1
/K
T
2.70
0.00303
3.39
0.00315
4.09
0.00327
4.43
0.00333
66
PMT
(i)
0.00300
0.00310
1
, on the grid below.
T
1 1
/K
T
0.00320
0.00330
2.0
3.0
log10k
4.0
5.0
(2)
67
PMT
(ii)
Ea 1
2.30 R T
Ea
1
has a gradient of
.
T
2.30 R
Calculate the gradient of the graph and hence calculate the value of activation
energy, Ea.
(2)
(Total 15 marks)
20.
This question is about the reaction between calcium carbonate and hydrochloric acid.
CaCO3(s) + 2HCl(aq) CaCl2(aq) + CO2(g) + H2O(l)
One method of studying the kinetics of this reaction is to measure the volume of carbon dioxide
given off at various timed intervals when using an excess of calcium carbonate.
68
PMT
(a)
Suggest TWO other methods for following this reaction. Explain your choices.
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(2)
(b)
Suggest why the volume of carbon dioxide given off in the first few seconds of the
reaction is an unreliable measure of the initial rate of the reaction.
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(1)
(c)
(i)
Time
/s
Volume of CO2
Vt/cm3
(Vfinal Vt)
/ cm3
85
35
42
46
65
62
26
95
72
125
79
155
84
185
87
69
PMT
(ii)
(iii)
(iv)
100
80
(Vfinal Vt )
/ cm 3
60
40
20
0
0
100
time / s
200
(2)
70
PMT
(v)
On your graph measure and record THREE successive half-lives. Deduce the order
of the reaction. Justify your answer.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(3)
(vi)
(1)
71
PMT
(d)
What would you expect the signs of Ssystem and Stotal to be for the reaction between
calcium carbonate and hydrochloric acid? Justify your answers.
Ssystem ..........................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
Stotal ............................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(4)
(Total 17 marks)
21.
S 2 O 82 (aq) + 2I (aq)
2SO 24 (aq) + I 2 (aq)
Initial rates for this reaction can be determined by a method known as an iodine clock.
A mixture of potassium iodide, sodium thiosulphate and starch is made up, and a clock started
when a solution of potassium peroxodisulphate is added. When enough iodine has been formed
to react with all the sodium thiosulphate, the excess iodine suddenly forms a blue-black
complex with the starch. At this point the clock is stopped, and the time taken.
(a)
In one particular experiment, the volumes of the reactants used were as follows:
Volume of
K2S2O8(aq)
/ cm3
Volume of
KI(aq) / cm3
Volume of
Na2S2O3(aq)
/ cm3
Volume of
starch solution /
cm3
Volume of
water / cm3
Time taken
/s
10.0
10.0
5.0
1.0
14.0
(i)
The concentration of the sodium thiosulphate used was 0.010 mol dm3. Calculate
the number of moles of thiosulphate ions, S 2 O 32 , in the mixture.
72
PMT
(1)
(ii)
I 2 (aq) + 2S 2 O 32 (aq)
2I (aq) + S 4 O 62 (aq)
Calculate the number of moles of iodine which had reacted when the clock was
stopped.
(1)
(iii)
(2)
(b)
Further experiments were carried out and the results are shown below.
Experiment
0.0100
0.0200
2.74 105
0.0100
0.0400
5.47 105
0.0300
0.0800
3.28 104
(i)
(ii)
73
PMT
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(1)
(iii)
Use your answers to (i) and (ii) to write an overall rate equation for the reaction.
(1)
(iv)
Use the data from experiment 1 to calculate the rate constant for this reaction.
Give the units for the rate constant.
(2)
(Total 9 marks)
22.
Initial concentration of
A /mol dm3
Initial concentration of
B /mol dm3
Initial rate
/mol dm3 s1
0.0500
0.100
1.00 104
0.0500
0.200
3.92 104
0.1000
0.100
1.95 104
(a)
(i)
Calculate, showing your working, the order of reaction with respect to A and to B.
74
PMT
(3)
(ii)
(iii)
Calculate the rate constant, k, for the reaction in experiment 3, stating its units.
(2)
75
PMT
(b)
(i)
Explain, in terms of collision theory, why the rate of reaction increases with an
increase in temperature.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(3)
(ii)
Suggest, with an explanation, the least number of steps which is likely to exist in
the mechanism of the reaction between A and B.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
76
PMT
(c)
The variation of the rate constant, k, with change in temperature is given by the Arrhenius
equation:
Ea
ln k =
R
1
+ ln A
T
where A is a constant.
In a series of experiments performed at various temperatures T to determine the rate
constant, k, for the decomposition of a gas X, a graph of ln k against 1/T gave a straight
Ea
line of slope
:
R
8
ln k
9
10
11
12
0.0029
0.0030
0.0031
0.0032
0.0033
0.0034
1
/ K 1
T
77
PMT
Use the graph to calculate the value of the activation energy, in kJ mol1, for the
decomposition of X. The value of the gas constant R = 8.31 J K1 mol1.
(4)
(Total 15 marks)
23.
In the presence of hydrogen ions, H+, glucose, C6H12O6, can be oxidised by a solution of
potassium manganate(VII), KMnO4, which is purple in colour.
A series of experiments was carried out to determine the rate of reaction and the results are
shown below.
Rate of
reaction
Initial
concentration
of C6H12O6
/ mol dm3
Initial
concentration
of KMnO4
/ mol dm3
Initial
concentration
of H+
/ mol dm3
/ mol dm3 s1
1.0
0.01
0.5
2.0 105
1.0
0.005
0.5
1.0 105
0.5
0.005
0.5
1.0 105
1.0
0.02
1.0
8.0 105
Experiment
78
PMT
(a)
Describe how the rate of this reaction may have been measured.
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(2)
(b)
(i)
Give the order of reaction with respect to each reactant. In the case of potassium
manganate(VII) and hydrogen ions explain how you arrived at your answer.
Glucose ................................................
Potassium manganate(VII) ...............................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
Hydrogen ions ..................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(3)
(ii)
79
PMT
(iii)
Using the data from experiment 1, calculate the rate constant for the reaction.
Include the units of the rate constant in your final answer.
(2)
(c)
Additional experiments were carried out to investigate the effect of temperature on the
rate of reaction.
(i)
1/ temperature (1/T)
/ K1
Rate constant
ln (rate constant)
295
3.39 103
2.88 103
5.85
305
3.28 103
1.01 102
4.60
1.83 102
311
320
3.13 103
4.98 102
3.00
333
3.00 103
2.02 101
1.60
(1)
80
PMT
(ii)
Plot a graph of ln (rate constant) on the vertical axis against 1/T on the horizontal
axis using the axes below.
(2)
(iii)
EA 1
+ constant, together with your
R
T
graph to calculate a value of the activation energy, EA, for this reaction.
Show all steps in your working. Include units in your final answer, which should be
given to two significant figures.
[Gas constant, R = 8.31 J K1 mol1]
Use the Arrhenius equation ln (rate) =
(2)
(Total 13 marks)
81
PMT
24.
The principal reaction occurring when 2-bromo-2-methylpropane reacts with aqueous sodium
hydroxide is as follows:
CH 3C(CH3)CH3 + NaOH
Br
CH3C(CH3)CH3 + NaBr
OH
Several experiments were carried out in order to follow the kinetics of this alkaline hydrolysis.
A few drops of phenolphthalein were added to a sample of sodium hydroxide, and, after the
addition of a measured amount of 2-bromo-2-methylpropane, the mixture was vigorously
shaken and a clock was immediately started. The time was taken when the pink colour due to
the indicator disappeared.
This experiment was repeated twice using different concentrations of the two reactants.
All experiments were carried out at the same temperature.
The results are shown in the table below.
Experiment
2-bromo-2-methylpropane
/ mol dm3
Sodium hydroxide
/ mol dm3
Time /s
0.011
8.0 104
33
0.022
8.0 104
16
0.022
1.2 103
24
(a)
(i)
(ii)
Assuming that the final concentration of sodium hydroxide is zero, calculate the
average rates of reaction in mol dm3 s1 for experiments A and B.
82
PMT
(iii)
(iv)
(v)
(vi)
From your rate equation, suggest how this reaction proceeds by giving a possible
mechanism.
(3)
83
PMT
(b)
25.
This question concerns the reaction between nitrogen monoxide and oxygen:
2NO(g) + O2(g) 2NO2(g)
(a)
In a series of experiments designed to find the rate equation for this reaction, the
following data were obtained. In each experiment the partial pressure of oxygen was the
same.
30
25
20
Initial rate / atm s
15
10
5
0
0.05
0.1
0.15
0.2
84
PMT
(i)
(ii)
A new series of readings is taken with the partial pressure of oxygen doubled.
The gradient of the line doubles.
State, with a reason, the order of reaction with respect to oxygen.
...........................................................................................................................
...........................................................................................................................
(1)
(iii)
(iv)
85
PMT
(b)
ln k = ln A
Ea 1
R T
where Ea is the activation energy for the reaction, R is the gas constant, and k is the rate
constant at temperature T.
(i)
Given values of k at different temperatures T, what graph would you plot and how
would you use it to determine the activation energy?
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
(ii)
A plot of the data gave a straight line with gradient 2.95 104 K1.
Find the activation energy for the reaction, in kJ mol1, to three significant
figures.
[The value of R is 8.314 J K1 mol1]
(2)
86
PMT
(iii)
+2
+1
2
(1)
(Total 10 marks)
26.
(i)
What information does this rate equation give about the mechanism of this reaction?
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(2)
87
PMT
(ii)
Give the mechanism for this reaction consistent with the rate equation.
(3)
(Total 5 marks)
27.
Suggest, in outline, THREE different methods for following the rate of this reaction.
State which of the reactants or products could be measured by each method you choose.
Method 1
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
Method 2
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
Method 3
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
(3)
88
PMT
(b)
(c)
A series of experiments was carried out, varying the concentrations of the reactants and
the catalyst. The following results were obtained.
Experiment
[CH3COCH3]
/mol dm3
[I2]
/mol dm3
[H+]
/mol dm3
Initial rate
/mol dm3 s1
1.00
0.010
0.10
2.8 106
1.00
0.010
0.20
5.6 106
1.50
0.010
0.20
8.4 106
1.50
0.020
0.10
4.2 106
(i)
Deduce the order of the reaction with respect to propanone, CH3COCH3. Justify
your answer.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(3)
89
PMT
(ii)
(iii)
(iv)
(v)
Suggest an equation for the reaction between the species in the rate-determining
step.
90
PMT
28.
This question involves the following techniques which can be used to follow chemical reactions
in order to investigate their kinetics.
A
colorimetry
(b)
91
PMT
(c)
(d)
(2)
92
PMT
(iii)
EA 1
rate = k[KI]2[C2H4Br2]
rate = k[KI]2
rate = k[C2H4Br2]
+ constant, together with your graph to calculate a value of the activation energy, EA, for this reaction.
Show all steps in your working. Include units in your final answer, which should be given to two significant
figures.
[Gas constant, R = 8.31 J K1 mol1]
(2)
(Total 13 marks)
93
PMT
30.
For the reaction between sodium bromate(V) and sodium bromide in acidic solution, the rate
equation is:
Rate = k[BrO3][Br][H+]2
When the concentrations of all three reactants are doubled, the rate will increase by a factor of
A
16
(Total 1 mark)
31.
This question is about the reaction of magnesium with hydrochloric acid which takes place
rapidly at room temperature.
Mg(s) + 2HCl(aq) MgCl2(aq) + H2(g)
(a)
H = 467 kJ mol1
94
PMT
(b)
Suggest the sign of the following entropy changes for this reaction. Justify each of your
answers.
(i)
Ssystem
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
(ii)
Ssurroundings
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(2)
(iii)
Stotal
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(1)
(c)
A student carried out this experiment at five different temperatures in order to calculate
the activation energy of the reaction. The students laboratory record is shown below.
Method
Clean a strip of magnesium weighing 0.100 g with sand paper. Measure the temperature of
20 cm3 of 1.00 mol dm3 hydrochloric acid in a 100 cm3 beaker. Add the magnesium ribbon,
stir continuously, and time how long it takes for the magnesium to disappear. Repeat the
experiment at four other temperatures.
Assumption: the initial rate of reaction is proportional to 1/time.
Results
Temperature
/C
Temperature
/K
1/T
/K1
time
/s
1/time
/s1
ln 1/time
24
297
3.37 103
45
0.0222
3.81
33
306
3.27 103
25
0.0400
3.22
45
318
3.14 103
11
0.0909
-2.40
56
329
3.04 103
0.1667
-1.79
10
283
3.53 103
122
0.0082
-4.80
95
PMT
Suggest the reason for cleaning the magnesium ribbon with sand paper.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(1)
96
PMT
(ii)
Calculate the number of moles of hydrochloric acid used up when all the
magnesium reacts in one experiment. Hence comment on whether the change in
concentration during the reaction will have a significant effect on the validity of the
assumption that the initial rate of reaction is proportional to 1/time. How would
you overcome this potential error?
[Take the relative atomic mass of magnesium as 24 in this and subsequent
calculations.]
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(5)
97
PMT
(iii)
Use the value of H and other information given in the question to calculate the
temperature change in an experiment assuming no energy is lost to the
surroundings. Hence comment on whether this change in temperature will have a
significant effect. How would you overcome this potential error?
[H = 467 kJ mol1.
heat produced = mass specific heat capacity change in temperature.
Assume that the specific heat capacity of the solution is 4.18 J K1 g1]
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(4)
98
PMT
(iv)
The most difficult thing to measure accurately is the time it takes for the
magnesium to disappear and the time measured can be up to 2 seconds out.
Assuming this error, calculate the shortest time at 56 C and the longest time at
10 C for this reaction.
Complete the table for these times. Plot the two points on the grid below and join
them with a straight line. From the gradient, which equals EA/R, of this line
calculate another value for the activation energy.
Temperature
/ C
Temperature
/K
1/T
/K1
56
329
3.04 103
10
283
3.53 103
0.0030
1.0
0.0031
0.0032
1 /T (K1)
0.0033
0.0034
time
/s
0.0035
1/time
/s1
ln 1/time
0.0036
1.5
2.0
ln 1 /t
2.5
3.0
3.5
4.0
4.5
5.0
99
PMT
(v)
If the reaction mixture is not stirred, the magnesium tends to float on the surface of
the acid.
Suggest how this would affect the measurements of the rate of the reaction.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(1)
(vi)
(vii) If ethanoic acid of the same concentration and at the same temperature is used
instead of hydrochloric acid, explain how the rate would differ.
...........................................................................................................................
...........................................................................................................................
...........................................................................................................................
(1)
(Total 24 marks)
100
PMT
32.
101