Physics 100 Simple Circuits

10

SAN DIEGO MESA COLLEGE

PHYSICS 100 LAB REPORT
TITLE: Simple Circuits

Objective:

Page 1 of

Name_________________________
Date __________Time___________
Partners ______________________
______________________________
______________________________
______________________________

To become familiar with the Circuits Experiment Board, to construct a complete electrical
circuit, and to represent electrical circuits with circuit diagrams.
To determine how light bulbs behave in different circuit arrangements. The different ways
of connecting two batteries will also be investigated.
To begin experimenting with variables that contribute to the operation of series, parallel
and combinations of circuits.

Theory:

Electric charge is measured in coulombs (C) and is designated by the letter q. Electric
charge in motion constitutes an electric current, measured in amperes (A) and designated
by the letter I. One coulomb is the electric charge delivered by a current of one ampere in
one second.
Work is done on electric charge by a source of energy such as a battery. The work done per
unit charge is electric potential, measured in volts (V) and designated by the same symbol,
V. One volt is one joule per coulomb. For instance, a six volt battery provides six Joules
of energy to each coulomb of electric charge that goes through it.
The energy provided by the battery is carried by moving charge (current) through the
circuit by connecting wires to some circuit component, such as an electrical resistance.
An electrical resistance is measured in ohms () and is designated by the symbol, R.
A simple electrical circuit is a means of delivering energy from a source to a user. The
source does work on electric charge; the user converts the electric energy to some more
useful form: heat, light, sound, and so on. Electric circuits are designed to deliver the
correct amount of energy at the proper rate to the designated user.

Equipment: Simple Circuit Boards

Digital Multimeter

Physics 100 Simple Circuits

10

Page 2 of

Setup:

Background:
Many of the key elements of electrical circuits have been reduced to symbol form. Each symbol
represents an element of the devices operation, and may have some historical significance. In this
lab and the ones which follow, we will use symbols frequently, and it is necessary that you learn
several of those symbols.

Notes on the Circuits Experiment Board:

The springs are soldered to the board to serve as convenient places for connecting wires,
resistors and other components. Some of the springs are connected electrically to devices
like the potentiometer and the D-cells.
If a spring is too loose, press the coils together firmly to enable it to hold a wire more
tightly. If a spring gets pushed over, light pressure will get it straightened back up. If you
find a spring which doesnt work well for you, please notify your instructor.
The components, primarily resistors, are contained in a plastic bag. Keep careful track of
the components, and return them to the bag following each lab period. This way you will
get components with consistent values from lab to lab.

Physics 100 Simple Circuits

10

Page 3 of

When you connect a circuit to a D-cell (each battery is just a cell, with two or more cells
comprising a battery) note the polarity (+ or -) which is imprinted on the board. Although
in some cases the polarity may not be important, in others it may be very important.

PART A:
Procedure:
Note: Due to variations from bulb to bulb, the brightness of one bulb may be substantially
different from the brightness of another bulb in identical situations.
Use two pieces of wire to connect a single light bulb to one of the D-cells in such a way that the
light will glow. Include a switch to turn the light on and off, preventing it from being on
continuously.
Use additional wires as needed to connect a second light into the circuit in such a way that it is also
lighted. Discuss your plans with your lab partner before you begin. Once you have achieved
success, sketch the connections that you made in the form of a circuit diagram using standard
symbols. Annotate your circuit diagram by making appropriate notes to the side indicating what
happened with that particular circuit. Is your original light the same brightness, or was it brighter
or dimmer than it was with just one light? Can you explain any differences in the
brightness or why it is the same?

If one of the light bulbs is unscrewed, does the other bulb go out or does it stay on? Explain why
or why not?
Design a circuit that will allow you to light all three lights, with each one being equally bright.
Draw the circuit diagram once you are successful. If you could characterize the circuit as being a
series or parallel circuit, which one would it be? What happens if you unscrew one of the bulbs?
Explain.

Design another circuit that will also light all three bulbs, but with the bulbs all being equally being
bright, even though they may be brighter or dimmer than in your previous circuit. Try it. When
you are successful, draw the circuit diagram. What happens if you unscrew one of the bulbs?
Explain.

Physics 100 Simple Circuits

10

Page 4 of

Devise a circuit that will light two bulbs at the same intensity, but the third at a different intensity.
Try it. When successful, draw the circuit diagram. What happens if you unscrew one of the
bulbs? Explain.

Are there any generalizations that you can state about the rules concerning different connections to
a set of lights? Answer below.

PART B:
Procedure:
Connect a single D-cell to a single light as in the first circuit of part A, using a spring clip switch
to allow you to easily turn the current on and off. Note the brightness of the light.

Now connect the second D-cell into the circuit as shown in figure 2.1a. What is the effect on the
brightness of the light?
Connect the second D-cell as in figure 2.1b. What is the effect on the brightness?
Finally, connect the second D-cell as in figure 2.1c. What is the effect on the brightness?

Determine the nature of the connections between the D-cells you made in the last three circuits.
Which of these was the most useful in making the light brighter? Which was the least useful? Can
you determine the reason why each behaved as it did?

Physics 100 Simple Circuits

10

Page 5 of

What are the apparent rules for connecting batteries in series? What are the rules for
a parallel connection ?

PART C:
Procedure:
Connect the circuit shown in figure 2.2.
What is the effect of rotating the knob on
the device that is labeled potentiometer?

PART D:
Procedure:
Choose three resistors as directed by your instructor. Enter those as sets of colors in Table 4.1
below. We will refer to one resistor as #1, another as #2, and a third as #3. Using the resistor
color code chart, determine the coded value of your resistors. Enter the value in the column
labeled Coded Resistance in table 4.1. Enter the tolerance value as indicated by the color of the
fourth band under Tolerance. Use the multimeter to measure the resistance of each of your three
resistors. Enter the values in table 4.1. Determine the percentage experimental error of each
resistance value and enter it in the % error column.
Measured - Coded
X 100%
Coded

Experimental Error =

Physics 100 Simple Circuits

10

1st

2nd

Page 6 of

Colors
3rd

4th

Coded
Measured
Resistance Resistance

%
Error

Tolerance

#1
#2
#3

Table 4.1
Resistor Color Code Chart:

SERIES:
Now connect the three resistors into the SERIES CIRCUIT, figure 4.1, using the spring clips on
the board to hold the leads of the resistor together without bending them. Measure the resistances
of the combinations as indicated on the diagram by connecting the leads of the multimeter between
the points at the ends of the arrows.

Physics 100 Simple Circuits

10

Page 7 of

PARALLEL:
Construct a PARALLEL CIRCUIT, first using combinations of two of the resistors, and then using
all three. Measure and record the values of these circuits (as shown in figure 4.2).

COMBINATION:
Connect the COMBINATION CIRCUIT below (figure 4.3) and measure the various combinations
of resistance. Do these follow the rules as you discovered before?
R2

R1 =

R1
3

R23 =
1

23
123

R123=
Fig. 4.3

Discussion:
How does the % error compare to the coded tolerance for your resistors?

What is the apparent rule for combining resistances in series circuits? In parallel circuits?
Cite evidence from your data to support your conclusions.

Physics 100 Simple Circuits

10

Page 8 of

What is the apparent rule for the total resistance when resistors are added up in series? In parallel?
Cite evidence from your data to support your conclusions.

PART E:
Procedure:
Connect the three resistors you used in part D into the series circuit shown below (figure 5.1),
using the springs to hold the leads of the resistors together without bending them. Connect two
wires to the D-cells carefully noting which wire is connected to the negative and which is
connected to the positive. Now use the voltage function on the multimeter to measure the voltages
across the individual resistors and then across the combinations of resistors. Be careful to observe
the polarity of the leads (red is +, black is -). Record your readings below.
SERIES:

R1 = ______________________
R2 = ______________________
R3 = ______________________
R12 = _____________________
R23 = _____________________
R123 = ____________________

V1 = _____________________
V2 = _____________________
V3 = _____________________
V12 = ____________________
V23 = ____________________
V123 = ___________________

Now connect the parallel circuit (figure 5.2), using all three resistors. Measure the voltage across
each of the resistors and the combination, taking care with the polarity as before.

Physics 100 Simple Circuits

10

Page 9 of

NOTE: Keep all three resistors connected throughout the time you are making your
measurements. Write down your values as indicated in figure 5.2.

PARALLEL:

Now connect the circuit below and measure the voltages. You can use the resistance readings
you took in part D for this step.

Physics 100 Simple Circuits

10

Page 10 of

COMBINATION:
+
R2

R1

V1 =

R23 =

V23 =

R123=

V123=

23
123

Fig. 5.3

Discussion:
On the basis of the data you recorded on the table with figure 5.1, what is the pattern for how
voltage gets distributed in a series circuit? Is there any relationship between the size of the
resistance and the size of the resulting voltage?

Utilizing the data from figure 5.2, what is the pattern for how voltage distributes itself in a parallel
circuit? Is there any relationship between the size of the resistance and the size of the resulting
voltage?

Do the voltages in your combination circuits (see Figure 5.3) follow the same rules as they did in?
your circuits which were purely series or parallel? If not, state the rules you see in operation.