TRANSPORTATION IMPACT ANALYSIS

CURRENT PRACTICE & GUIDELINES

Prepared by:
Transportation Complete Streets Division
Department of Transportation

20150113

This document may be reprinted or extracted without permission, provided credit

to the City of Pasadena Department of Transportation
For comments or additional questions regarding the Departments
transportation review practice, please contact:
Pasadena Department of Transportation
Transportation Complete Streets Division
http://www.cityofpasadena.net/Transportation/

The Departments current review practice will be periodically updated and posted
on:
http://www.cityofpasadena.net/Transportation/Transportation_Impact_Review/

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.2

Table of Contents
Section 1: BACKGROUND, PURPOSE, & PROCESS ............................................................. 5
Section 2: THRESHOLDs .......................................................................................................... 9
Section 3: PROCEDURES FOR PREPARING A TRANSPORTATION IMPACT ANALYSIS 18
I. Overall Process of a Transportation Impact Analysis (TIA) ............................................. 18
II.
Transportation Impact Analysis- Report Format ......................................................... 19
ATTACHMENTS ........................................................................................................................... 23
Transportation Impact Analysis (TIA)-Sample MOU ............................................................... 24
Description of Transportation Performance Metrics ................................................................... 26

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.3

SECTION 1:
INTRODUCTION, BACKGROUND, AND
PROCESS

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.4

SECTION 1: BACKGROUND, PURPOSE, & PROCESS

BACKGROUND
The following guidelines support Pasadenas vision of creating a community where
people can circulate without cars. The vision relies upon an integrated and multimodal
transportation system that provides choices and accessibility for everyone living and
working in the City. Key strategies to achieve this vision promote non-auto travel
including public transit services, parking strategies, bicycle facilities, and pedestrian
components that are well coordinated and connected with a larger regional
transportation system.
PURPOSE
The ability of a community to balance and facilitate the different components of its
transportation system is important to the creation and preservation of a quality living and
business environment. The function of a communitys transportation system is to
provide for the movement of people and goods, including pedestrians, bicyclists, transit
and other vehicle traffic flows within and through the community.
The Mobility Element of the Citys General Plan sets forth goals and policies to improve
overall transportation in Pasadena. The Mobility Element is based on approaches that
address the needs of multimodal corridors and streets as well as community
neighborhoods that are affected by traffic. These guidelines have been developed to
ensure that transportation system improvements necessary to support new
development while maintaining quality of life within the community are identified prior to
project approval and funded prior to construction.
Transportation impact analyses are an integral part of the environmental review process
that is required for all proposed projects that are not categorically exempt under the
California Environmental Quality Act (CEQA). Under CEQA, jurisdictions have the right
to categorically exempt projects consisting of less than five housing units and nonresidential projects with less than 2,500 square feet of floor area (CEQA 15303).
Projects exempt under this class are qualified by consideration of where the project is
located. If a project may impact an environmental resource or the location may be of
critical concern, the project cannot be categorically exempt. Projects characterized as

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.5

in-fill development may also be categorically exempt if they meet the conditions
described in Section 15332 of the CEQA Guidelines as follows:
1. The project is consistent with the applicable general plan designation and all
applicable general plan policies as well as with applicable zoning designation and
regulations
2. The proposed development occurs within city limits on a project site of no more
than five acres substantially surrounded by urban uses
3. The project site has no value as habitat for endangered, rare, or threatened
species
4. Approval of the project would not result in any significant effects relating to traffic,
noise, air quality, or water quality
5. The site can be adequately served by all required utilities and public services
These guidelines have been developed to identify projects that may have transportation
impacts and to provide step-by-step instructions for preparing a Transportation Impact
Analysis.
PROCESS
Upon receipt of initial Project Plan Review (PPR) from city of Department of Planning
and Community Development, the City of Pasadena Department of Transportation
(PasDOT) will determine whether or not a transportation review is required relative to
CEQA guidelines and City policies. If a review is required, the following steps describe
the process for initiating the process:
1. Applicant contacts PasDOT with a request to commence the study
2. PasDOT will estimate the required fees for conducting the study.
3. Upon authorization to proceed and payment of fees, PasDOT will commence the
analysis.
Traffic Counts
1. Traffic counts shall be collected in accordance with industry standards and
established methodologies and at PasDOTs discretion.
2. Counts should be collected when schools and colleges are in session. Counts
collected when schools and/or colleges are not in session shall be approved by
the Director of Transportation.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.6

3. Counts should be collected during AM (7 a.m. to 9 a.m.) and PM (4 p.m. to 6

p.m.) peak hours, unless otherwise specified. Midday and Weekend counts may
also be required.
Trip Generation and Applicable Credits
Trip generation is determined by one or more of the following:
th

1. Institute of Transportation Engineers (ITE) Trip Generation, 9 Edition or most

current edition.
a. Rates should be calculated using the weighted average formula when

applicable
b. Special consideration should be given for ITE rates based on antiquated

data or a small sample may require additional data collection to determine

the appropriate trip generation
2. Counts conducted for existing projects that are relocating or expanding
3. New rates should be generated using community examples for uses not

updated or included in the ITE Trip Generation publication

4. Trip credits are given to certain uses located on major corridors and/or within

the Transit Oriented District (TOD). The trip discounts are determined on a
case by case basis and must be consistent with the Citys current practice
5. For new uses, parking demand should be based on ITE Parking Generation

Handbook and/or parking demand analyses conducted for similar uses in the
community

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.7

SECTION 2:
THRESHOLDS USED FOR DETERMINING
TRANSPORTATION REVIEW OF PROJECTS

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.8

SECTION 2:

THRESHOLDS

Thresholds for Determining Transportation Review

Pasadenas current practice for reviewing a projects transportation impact begins with
the submittal to the Pasadena Planning & Community Development Department of
either a Project Plan Review (PPR), or an application for a discretionary action,
including but not limited to a master development plan, planned development,
conditional use permit, variance, hillside development permit, design review, and/or a
request to alter the assessors map.
PasDOT reviews several types and sizes of projects that could be subject to
environmental review under the California Environmental Quality Act. The Department
has two processes for reviewing a proposed projects transportation impacts based on
project size, consisting of below or equal to communitywide significance
thresholds, and above communitywide significance thresholds. Communitywide
significance projects are defined as 50,000 square feet of new commercial use, 50
residential units, or any combination of the two. The primary difference between
the two types of transportation review is inclusion of street segment and Level of
Service (LOS) analyses. Additionally, street segment analysis and LOS analysis may
be required for smaller projects at the discretion of the Director of Transportation. The
following table summarizes the thresholds of determination.
Table 1: Thresholds for Determining Transportation Review of Projects
TYPE OF
PROJECT

EXEMPTION

Category 1:
BELOW
COMMUNITYWIDE
SIGNIFICANCE

Residential
(Net # of
units)

10 units or less

11 49 units

50+ units

NonResidential
Use (Net)

10,000 Sq Ft or
less than 300
daily trips

10,001 to 49,999
Sq Ft

50,000+ Sq Ft

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

Category 2:
COMMUNITYWIDE
SIGNIFICANCE

1.9

Thresholds for Determining Impacts

The guidelines apply to all projects that require environmental review in accordance with
the California Environmental Quality Act and the Citys established Environmental Policy
Guidelines, significance thresholds, and transportation review guidelines. The
thresholds contained herein determine a projects expected level of impact on the
transportation system and identify appropriate types of mitigation.
Table 2- Metrics CEQA Thresholds of Significance

IMPACT THRESHOLD

METRIC

DESCRIPTION

VMT Per
Capita*

Vehicle Miles Traveled (VMT)

in the City of Pasadena per
service population (population
+ jobs).

2.

VT Per
Capita

Vehicle Trips (VT) in the City

of Pasadena per service
population (population + jobs).

CEQA Threshold: An increase over existing

Citywide VT per Capita of 2.8.

3.

Proximity
and Quality
of Bicycle
Network

Percent of service population

(population + jobs) within a
quarter mile of each of three
bicycle facility types

CEQA Threshold: Any decrease in existing

citywide 31.7% of service population (population +
jobs) within a quarter mile of bike facilities.

4.

Proximity
and Quality
of Transit
Network

Percent of service population

(population + jobs) located
within a quarter mile of each
of three transit facility types.

CEQA Threshold: Any decrease in existing

citywide 66.6% of service population (population +
jobs) within a quarter mile of Transit Facilities.

Pedestrian
Accessibility

The Pedestrian Accessibility

Score uses the mix of
destinations, and a networkbased walk shed to evaluate
walkability

CEQA Threshold: Any decrease in the Citywide

Pedestrian Accessibility Score

1.

5.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

CEQA Threshold: An increase over existing

Citywide VMT per Capita of 22.6.

1.10

Table 3- Metrics Cap Outside of CEQA

METRIC
1.

Street
Segment
Analysis

DESCRIPTION

CAP

The street segment analysis

assesses traffic intrusion on
local streets in residential
neighborhoods

Increases of 10-15% above existing on streets

with more than 1500 ADT would trigger conditions
of approval to reduce project vehicular trips

Level of Service (LOS) as

defined by the Transportation
Research Board's Highway
Capacity Manual (HCM) 2010.

A decrease beyond LOS D Citywide or LOS E

within Transit Oriented Districts (TODs) would
trigger conditions of approval to reduce project
vehicular trips

2.

Auto Level
of Service

3.

PEQI

Pedestrian Environmental
Quality Index

Below average Conditions

4.

BEQI

Bicycle Environmental Quality

Index

Below average conditions

All metrics in Tables 2 and 3 shall be analyzed for projects of communitywide

significance under Category 2 in Table 1. All or any of the metrics in Table 3 might be
required for analysis for Category 1 projects in Table 1 at the discretion of Director of
Transportation.
Street Segment Analysis (Increase in Daily Traffic)
Street Segment Analysis to address impacts to neighborhoods from traffic intrusion.
The Average Daily Traffic (ADT) caps in Table 4 below measure the relative change in
daily traffic resulting from an increase in trips or a change in access that alters existing
traffic patterns. The relative change in daily traffic is determined as follows:
Percentage of Increase = Net New Project Trips/Existing Daily Traffic
A Street Segment analysis is required for all Category 2 projects identified in Table 1, or
smaller projects at the discretion of Director of Transportation. The following criteria will
be used for street segment analysis:

Applies to Projects of Communitywide Significance which are defined as 50,000

square feet of new commercial use, 50 residential units or more, or any
combination of the two (Category 2 project in Table 1).
May apply to smaller projects identified as Category 1 projects in Table 1 at
discretion of Director of Transportation

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.11

The analysis would be limited to Access and Neighborhood Connector street

types within a residential context (Street Types Map below)
Table 4- ADT Caps for Requiring Neighborhood Traffic Calming Measures
Existing ADT

Project-Related Vehicular Increase In ADT

0 to 1500

150 or more

1,501 to 3,499

10 percent or more of final ADT

3,500 or more

8 percent or more of final ADT

If project-related net trips exceed the caps in the table above conditions of approval
would require the project applicant to develop and implement a targeted Complete
Streets Plan with input from the affected residents, council districts and DOT to
encourage use of non-vehicular modes by the projects patrons, and implement
measures to discourage use of residential streets to-and-from the project site. Below is
a list of typical measures that would be included in a Complete Streets Plan.
Project specific measures:

Establish a more aggressive Average Vehicle Occupancy (AVO) target that

exceeds citys AVO average by enhancing the required TDM plan under Citys
Trip Reduction Ordinance (TRO)
Project turn-restrictions
Revised project access and circulation
Complete Streets measures

Curb Extensions
Pedestrian and Bike Traffic signal upgrades/enhancements
Turn-restrictions
Neighborhood Gateways (raised medians)
Traffic circles
Speed humps
Signal metering

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.12

Map 1- City of Pasadena Adopted Street Types

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.13

Level of Service (LOS) Analysis

A 2010 Highway Capacity Manual (HCM) intersection Level of Service (LOS) analysis
will be applied to proposed new development projects that meet or exceed the size
thresholds to be Projects of Communitywide Significance, or smaller projects at the
discretion of Director of Transportation. The LOS results will be measured for
compliance with the intersection LOS caps in Table 5 below.
Table 5- Signalized Intersections LOS Cap
Study Intersections
Existing + Project LOS Cap
Citywide
D
Transit Oriented District (TOD)-see Map 2
E
Intersection LOS analysis using HCM criteria shown in Table 6 is conducted for peak
hour conditions (morning, mid-day or evening or combination, depending upon size and
location of the proposed project). The number of intersections to be analyzed will vary
also depending upon size and location of the proposed project. Where the evaluated
intersections exceed the LOS caps, conditions of approval will be recommended
consistent with the Citys Guiding Principles to encourage walking, biking and transit toand-from the project site to reduce project-related vehicular trips. Below is a list of
typical measures that would be included in trip reduction programs:
Project specific measures:
o Establish an Average Vehicle Occupancy (AVO) Cap or more aggressive AVO
target that exceeds the Citys AVO average by enhancing the required TDM
plan under the Citys Trip Reduction Ordinance (TRO)
o Parking strategies to share parking or reduce on-site parking
o Transit passes and/or transit cash-out
o Bikeshare program with 10 or more bikes
o Carshare program with two or more vehicles
o Shuttle service to major transit stops
o On-site transit kiosk
Complete Streets measures
o Pedestrian lighting to and from major transit stops
o Pedestrian and Bike Traffic signal upgrades/enhancements
o Installation of non-vehicular improvements at studied intersections

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.14

Peak Hour

Intersection

Level of Service analysis should be developed in a table form as follows:

Existing
Delay

Existing w/Project
LOS

Delay

Exceeds LOS Cap?

LOS

Yes/No

TABLE 6- HIGHWAY CAPACITY LEVEL OF SERVICE CRITERIA

LEVEL OF
SERVICE

DESCRIPTION

DELAY IN
SECONDS

Progression is extremely favorable and most vehicles arrive during the green
phase. Most vehicles do not stop at all. Short cycle lengths may also
contribute to low delay.

< 10.0

Progression is good, cycle lengths are short, or both. More vehicles stop than
with LOS A, causing higher levels of average delay.

> 10.0 to
20.0

Higher congestion may result from fair progression, longer cycle lengths, or
both. Individual cycle failures may begin to appear at this level, though many
still pass through the intersection without stopping.

> 20.0 to
35.0

The influence of congestion becomes more noticeable. Longer delays may

result from some combination of unfavorable progression, long cycle lengths,
or high V/C ratios. Many vehicles stop, and the proportion of vehicles not
stopping declines. Individual cycle failures are noticeable.

> 35.0 to
55.0

This level is considered by many agencies to be the limit of acceptable delay.

These high delay values generally indicate poor (vehicle) progression, long
cycle lengths, and high V/C ratios. Individual cycle failures are frequent
occurrences.

> 55.0 to
80.0

This level is considered oversaturation, which is when arrival flow rates exceed
the capacity of the intersection. This level may also occur at high V/C ratios
below 1.0 with many individual cycle failures. Poor progression and long cycle
lengths may also be contributing factors to such delay levels.

> 80.0

Source: 2010 Highway Capacity Manual.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.15

Map 2- City of Pasadena Adopted Transit Oriented Districts

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.16

SECTION 3:
PROCEDURES FOR PREPARING A
TRANSPORTATION IMPACT ANALYSIS
(TIA)

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.17

SECTION 3: PROCEDURES FOR PREPARING A TRANSPORTATION

IMPACT ANALYSIS
The following procedures have been established for the preparation of a Transportation
Impact Analysis (TIA). A TIA is intended to focus on an accurate field inventory of
existing circulation elements, and provide recommendations for incorporating existing
and/or recommended circulation elements into the design of the proposed project to
ensure safety and compatibility. Approval of a TIA generally occurs six (6) to eight (8)
weeks after the City receives the authorization to proceed and the deposit to fund the
analysis from the applicant.
I. Overall Process of a Transportation Impact Analysis (TIA)
a. The Department of Transportation reviews applications for Project Plan
Review (PPR) and other discretionary approvals to determine what types of
analysis must be prepared in accordance with the Citys established
thresholds in Section 2.
b. Based on the project scope provided in the application, DOT staff will prepare
a draft Memorandum of Understanding (MOU) for review and approval by the
applicant or applicant representative and Planning & Community
Development Department staff.
c. The applicant shall submit the signed authorization to proceed along with a
deposit for preparing the TIA. The fee amount will be based on citys fee
schedule adopted by Council at the time of submittal. The deposited fee will
be subject to additional billing or refund.
d. Staff will develop, examine, and recommend feasible transportation
improvements. The recommendations will be incorporated into the report
based on their consistency with the Mobility Element, Neighborhood Traffic
Management Program, adopted specific plans, and the Capital Improvement
Program.
e. The Department of Transportation case manager may forward the preliminary
recommended transportation improvements to the applicant for information.
f. Based on the Transportation Impact Analysis findings, the Department of
Transportation will notify the Planning & Community Development
Department with a list of transportation improvements pertaining to the

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.18

proposed project as part of the approval process.

II. Transportation Impact Analysis- Report Format

Cover Page
A cover page containing the project address and name (if applicable), as well as
the date, and consultant contact information.
Table of Contents
Section 1: PROJECT DESCRIPTION
1. Type, size, and number of parking spaces
2. Vehicular trip generation estimates
3. Circulation Plan

SECTION 2: FIELD SURVEY, DOCUMENT AND/OR IDENTIFY POTENTIAL

IMPROVEMENTS FOR THE FOLLOWING:
1. Digital photo documentary of the project site, key street features,
inventory of transportation elements.
2. Existing site (use, access, pedestrian walkways, etc.)
3. Adjacent intersections (both signalized and non-signalized), including
lane configurations, type of controls, and any special traffic-related
features/conditions (grade, curvature, raised medians, etc.);
4. Residential neighborhoods near the project;
5. General land uses on the same and adjacent blocks of the project;
6. On-street parking restrictions and utilization on the adjacent street and
nearby street(s);
7. Transit facilities within 800 feet of the project, including the service
provider(s) (Pasadena ARTS, MTA, Foothill Transit,) and location,
amenities, and condition of existing bus stops;

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.19

8. Ingress/egress of proposed use, such as sight visibility, potential need for

parking restrictions, location of access gate, etc.;
9. Bicycle facilities, including bike lane/route designations on adjacent
streets, existing bike racks/parking on or adjacent to site, and proposed
on-site bicycle amenities; and,
10. Pedestrian amenities, such as sidewalk widths adjacent to the project
and pedestrian indicators at the nearest signalized intersection.
SECTION 3: IDENTIFY PROJECT IMPACTS
1. Vehicle Miles Travelled (VMT) per Capita: Estimate projects incremental
change in VMT per capita using Citys Travel Demand Forecasting Model
2. Vehicle Trips (VT): Estimate projects incremental change in VT per capita
using Citys Travel Demand Forecasting Model
3. Bicycle and Transit Facilities: Assess proximity and quality of bicycle and
transit networks by estimating projects change in percent of dwelling units
and jobs within a quarter mile of bicycle and transit facilities.
4. Pedestrians Accessibility:
Estimate Projects change in Citywide
Pedestrian Accessibility Score.
5. Trip Generation: Estimate projects vehicular trip generation using the Trip
Generation Manual, current edition, published by the Institute of
Transportation Engineers as the primary document. Other trip production
rates can be used if approved by the Department of Transportation. Any
adjustments to standard rates, such as for special uses, mixed uses, high
transit use, or pass-by trips must be approved by the City Traffic Engineer.
6. Study Street Segments and Intersections: The Department of
Transportation will identify study street segments and intersections within
the primary influence area of the proposed development.
A. Traffic Count Data:
a. The Department of Transportation will require evaluation of all
critical time periods based on the proposed uses and site location.
b. Unless otherwise specified, peak hours occur between 7:00 and
9:00 a.m. and between 4:00 and 6:00 p.m. Pedestrian and bicycle
counts must be collected.
B. Study street segments

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.20

a. Describe speed limits, stop control, pedestrian crossings, and

parking restrictions)
b. Street segment analysis
C. Study intersections
a. Describe speed limits, stop control, pedestrian crossings, and
parking restrictions, and include a diagram of existing lane
configurations
b. Display existing peak hour traffic volumes
c. Distribute project trips (include distributions for each peak hour in
percentages and volumes). The traffic distribution is a prediction
of the future travel paths of site users. It is generally based on
population distribution and significant travel paths in the study
area. The trip distribution is to be approved by the Department of
Transportation prior to preparation of the report.
d. Analyze intersection impacts
e. Conduct CMP analysis (if applicable)
f. Identify potential construction impacts
g. Recommend mitigation measures. Developments must mitigate
the increase in traffic caused by their development. Mitigation
measures are required when level of service at any study
intersection or on any street segment exceeds the thresholds
contained in Section 2. If mitigation reflects trip reductions
predicted as a result of implementing required Transportation
Demand Management (TDM) measures, an approved report must
be submitted substantiating such mitigation. All proposed
roadway mitigation must be illustrated and a preliminary cost
estimate provided to show the new intersection configuration,
including lane widths, assignments, widenings, and trip reduction
attributed to required TDM strategies.
7. Study Pedestrian and Bike Impacts
The Department of Transportation will identify study street segments
within the primary influence area of the proposed development.
a. Collect data elements that directly impact pedestrians,
bicyclists, and transit operations along the street segment(s),
b. Analyze the project impacts on pedestrians and bicyclists using
industry standard methodologies such as PEQI, BEQI.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.21

c. Require measures to improve the environmental quality of nonvehicular modes when the findings reveal less than average
conditions (Please see Section 2, Table 3).
SECTION 4: IDENTIFY TRANSPORTATION IMPACTS
Summarize the transportation impact based on data collected for Section 3 and
recommend prioritization for appropriate improvements that address increases in
traffic on analyzed street segments.

SECTION 5: GENERAL PLAN MOBILITY ELEMENT CONSISTENCY CHECK

Identify and incorporate specific transportation-related elements that support the
Citys goal of becoming a city where people can circulate without cars. Also
identify and incorporate improvements that will protect nearby residential streets
by encouraging project-related traffic to utilize multimodal corridors and/or
through neighborhood traffic calming measures.

SECTION 6: CONCLUSION & RECOMMENDATIONS

Summarize key findings and elements to be incorporated into the development of
the project, such as changes in access and recommended locations for bicycle
amenities.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.22

ATTACHMENTS

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.23

Transportation Impact Analysis (TIA)-Sample MOU

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.24

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.25

Description of Transportation Performance Metrics

1. VMT PER CAPITA
The Vehicle Miles Traveled (VMT) per Capita measure sums the miles traveled for trips within the City of
Pasadena Travel Demand Model. The VMT total considers only trips that begin inside the Pasadena and
50% of the distance travelled along roads outside of Pasadena. The Citys VMT is then divided by the
Citys total service population, defined as the population plus the number of jobs.
Although VMT itself will likely increase with the addition of new residents, the City can reduce VMT on a
per-capita basis with land use policies that help Pasadena residents meet their daily needs within a short
distance of home, reducing trip lengths, and by encouraging development in areas with access to various
modes of transportation other than auto.
2. VT PER CAPITA
Vehicle Trips (VT) per Capita is a measure of motor vehicle trips associated with the City. The measure
sums the trips with origins and destination within the City of Pasadena, as generated by the 2013 Tripbased citywide Travel Demand Model. The regional VT is calculated by adding the VT associated with
trips generated and attracted within City of Pasadena boundaries, and 50% of the VT associated with
trips that either begin or end in the City, but have one trip end outside of the City. The Citys VT is then
divided by the Citys total service population, defined as the population plus the number of jobs.
As with VMT, VT itself will likely increase with the addition of new residents, but the City can reduce VT
on a per-capita basis with land use policies that help Pasadena residents meet their daily needs within a
short distance of home, reducing trip lengths, and by encouraging development in areas with access to
various modes of transportation other than auto.
3. PROXIMITY AND QUALITY OF BICYCLE NETWORK
The Proximity and Quality of Bicycle Network provides a measure of the percent of the Citys service
population (population + jobs) within a quarter mile of each of three bicycle facility types. The facility types
are aggregated into three hierarchy levels, obtained from the Citys 2012 (Draft) Bicycle Transportation
Plan categories as shown in Table 1.

TABLE 1 BIKE FACILITIES HIERARCHY

LEVEL
1 (A)

DESCRIPTION
Advanced Facilities

FACILITIES INCLUDED
Bike Paths (P1)
Multipurpose Paths (PP)
Cycle Tracks/Protected Bike Lanes

2 (B)

Dedicated Facilities

Buffered Bike Lanes

Bike Lanes (2, P2)
Bike Boulevards (BB)

3 (C)

Basic Facilities

Bike Routes (3, P3)

Enhanced Bike Routes (E3, PE3)
Emphasized Bikeways (PEB)

Source: City of Pasadena Bicycle Transportation Plan, 2012.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.26

For each bike facility level, a quarter-mile network distance buffer is calculated and the total
service population (population + jobs) within the buffer are added.
The City can improve measures of Bike Facility Access by improving and expanding existing
bike facilities and by encouraging residential and commercial development in areas with highquality bike facilities.
4. PROXIMITY AND QUALITY OF TRANSIT NETWORK
The Proximity and Quality of Transit Network provides a measure of the percent of the Citys
service population (population + jobs) within a quarter mile of each of each of three transit
facility types, as defined in the Streets Types Plan and in Table 2.

TABLE 2 TRANSIT FACILITIES HIERARCHY

FACILITIES INCLUDED

LEVEL
1 (A)

Includes all Gold Line stops as well as corridors with transit service, whether it
be a single route or multiple routes combined, with headways of five minutes or
less during the peak periods.

2 (B)

Includes corridors with transit headways of between six and 15 minutes in peak
periods.

3 (C)

Includes corridors with transit headways of 16 minutes or more at peak periods.

Source: Draft Streets Types Plan, Pasadena Department of Transportation, March 2013.

For each facility level, a quarter-mile network distance buffer is calculated and the total service
population (population + jobs) within the buffer are added.
The City can improve the measures of Transit Proximity and Quality by reducing headways on
existing transit routes, by expanding transit routes to cover new areas, and by encouraging
residential and commercial development to occur in areas with an already high-quality transit
service.
5. PEDESTRIAN ACCESIBILITY
The Proximity and Quality of Pedestrian Environment provides a measure of the average
walkability in the TAZ surrounding Pasadena residents, based on a Pedestrian Accessibility
metric. The Pedestrian proximity metric is a simple count of the number of land use types
accessible to a Pasadena resident or employee in a given TAZ within a 5-minute walk. The ten
categories of land uses are:

Retail
Personal Services
Restaurant

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.27

Entertainment
Office (including private sector and government offices)
Medical (including medical office and hospital uses)
Culture (including churches, religious and other cultural uses)
Park and Open Space
School (including elementary and high schools)
College

The resulting count of land use types is then assigned a letter grade from A to D based on the
following structure:

A greater than or equal to 8 land use types

B greater than or equal to 5 land use types and less than 8 land use types
C greater than or equal to 2 land use types and less than 5 land use types
D greater than or equal to 0 land use types and less than 2 land use types

The City can improve the Resident and Employment Pedestrian Accessibility Scores by:

Encouraging residential development in areas with high existing Pedestrian Accessibility

Scores;
Encouraging commercial development in areas with high existing Pedestrian
Accessibility Scores; and
Attracting mixed development and new land use types to increase the Pedestrian
Accessibility metric values of other areas.

TRANSPORTATION IMPACT ANALYSIS GUIDELINES

1.28