0% found this document useful (0 votes)
107 views4 pages

Design of Bracket: BR-1 &BR-2

The document provides design details for brackets BR-1 and BR-2. It specifies the grade of concrete as M25, grade of steel as 415 N/mm^2, and a vertical load of 30 kN applied 225 mm from the face of the wall. The effective depth is 470 mm, overall depth is 500 mm, and maximum permissible concrete stress is 3.1 N/mm^2. Using the specified criteria, the effective depth is determined to be sufficient at 255 mm. Shear design calculations show the required shear steel is 2 legs of 8 mm bars. Development length calculations show the minimum length required is 821 mm.

Uploaded by

kushaljp8989
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
107 views4 pages

Design of Bracket: BR-1 &BR-2

The document provides design details for brackets BR-1 and BR-2. It specifies the grade of concrete as M25, grade of steel as 415 N/mm^2, and a vertical load of 30 kN applied 225 mm from the face of the wall. The effective depth is 470 mm, overall depth is 500 mm, and maximum permissible concrete stress is 3.1 N/mm^2. Using the specified criteria, the effective depth is determined to be sufficient at 255 mm. Shear design calculations show the required shear steel is 2 legs of 8 mm bars. Development length calculations show the minimum length required is 821 mm.

Uploaded by

kushaljp8989
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 4

DESIGN OF BRACKET

BR-1 &BR-2
GRADE OF CONCRETE
GRADE OF STEEL
VERTICAL LOAD
DISTANCE FROM FACE OF WALL TO LOAD POINT
WIDTH OF BRACKET
EFFECTIVE DEPTH OF THE BRACKET
OVERALL DEPTH OF THE BRACKET
MAX. PERMISSIBLE STRESS IN CONCRETE

Fck

25

N/mm2

Fy
"V"
"a"
B
"d"
"D"

415
30
225
450
470
500

N/mm2
KN
mm
mm
mm
mm
N/mm2

" Tc max "

3.1

EFFECTIVE COVER

d'

30

mm

USING DIA OF BAR

"DIA"

20

mm

Vu

33

KN

23.66
470
510
255

mm
mm
mm
mm

FACTORED VERTICAL LOAD


(1) DEPTH SHALL BE DECIDED BY FOLLOWING CRITERIA
(i) FOR BRACKETS
Effective depth
Provided effective depth is

Fv / (Tc .b)

"d"

Total Depth at support


Depth at face

a / d > 0.6

"Ds"
"Df"

0.48

(ii) FOR SHEAR


d<Vu/(Tc max x b)

23.66

Effective depth is safe

SAFE

mm

SAFE

Vu =0.36 x fck x b x Xu x (a x Zu)


(a2 + Zu2)
Vu =

4050

Xu x

225 Zu
50625 + Zu2

(Assume)

Zu =
d - 0.42 x Xu
To calculate the value of Xu & Zu Use trial and error procedure
by varrying of neutral axis depth
Xu
Zu
Vu
Vu
0.9
423
292.34
828032
33000
N
828.03
33.00
Kn

OK

(iii) MAIN STEEL : Ast


Tu = VuD x (a/Zu)
fst
Required Ast = Tu / fst
% steel

25.40

kN

77.78

N/mm2

=
=

326.55
0.15

mm2
%

Minimum Pt % of Steel is

0.4

Maximum Pt % of Steel is

1.3

0.40

846

mm2

371

mm

2.69

No's

Pt % of Steel
Ast
(iv) NO OF BARE'S USED:
Spacing
Ast/ast

Depth is Sufficient

(2) SHEAR DESIGN :


beeta1
beeta1
tc =
Vuc = Tuc x (2xd/a)
Vuc = Vuc.max

Vuc < Tuc max


=Tuc.max x b x d
=

7.26

7.26
0.4457807366 N/mm2
1.86

N/mm2

655.65

KN

12

mm

S = 0.87 x fy x Asv / (0.4 x b )

226.85

mm

No of Bar's Using

No's

1.4

N/mm2

821

mm

Minimum Stirrups are sufficient


Using 2-legged Stirrups,
Use Reinforcement Dia

(3) DEVELOPMENT LENGTH :


(For M25 Design Bond Strees from IS 456_2000 )
Tbd
Ld =( x s ) / ( 4 x Tbd)

SAFE

You might also like