Green Technology in Cement PDF

International Journal of Sustainable Built Environment (2012) 1, 194216
Gulf Organisation for Research and Development
International Journal of Sustainable Built Environment

SciVerse ScienceDirect
www.sciencedirect.com
Review Article
Trends and developments in green cement and concrete technology

Mohammed S. Imbabi , Collette Carrigan, Sean McKenna
School of Engineering, Kings College, The University of Aberdeen, AB24 3UE Scotland, UK
Received 20 February 2013; accepted 13 May 2013
Abstract
The cement industry faces a number of challenges that include depleting fossil fuel reserves, scarcity of raw materials, perpetually
increasing demand for cements and concretes, growing environmental concerns linked to climate change and an ailing world economy.
Every tonne of Ordinary Portland Cement (OPC) that is produced releases on average a similar amount of CO2 into the atmosphere, or
in total roughly 6% of all man-made carbon emissions. Improved production methods and formulations that reduce or eliminate CO2
emissions from the cement manufacturing process are thus high on the agenda. Emission reduction is also needed to counter the impacts
on product cost of new regulations, green taxes and escalating fuel prices. In this regard, locally available minerals, recycled materials
and (industry, agriculture and domestic) waste may be suitable for blending with OPC as substitute, or in some cases replacement, binders. Fly ash, Blast furnace slag and silica fumes are three well known examples of cement replacement materials that are in use today that,
like OPC, have been documented and validated both in laboratory tests and in practice. The rst is a by-product of coal combustion, the
second of iron smelting and the third of electric arc furnace production of elemental silicon or ferro silicon alloys. This paper presents a
concise review of the current state-of-the-art and standards underpinning the production and use of OPC-based cements and concretes. It
outlines some of the emerging green alternatives and the benets they oer. Many of these alternatives rely on technological advances
that include energy-ecient, low carbon production methods, novel cement formulations, geopolymers, carbon negative cements and
novel concrete products. Finally, the economics of cement production and the trends in the UK, US and the Gulf Cooperation Council
(GCC) Region are presented, to help guide and inform future developments in cement production based on maximizing the value of
carbon reduction.
2013 The Gulf Organisation for Research and Development. Production and hosting by Elsevier B.V.
Open access under CC BY-NC-ND license.
Keywords: Cement Standards; Energy; Economics; Carbon
Contents
1.
2.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Portland-based cements and other hydraulic binders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Corresponding author. Tel.: +44 1224 272506.
E-mail addresses: [email protected], [email protected] (M.S. Imbabi).

Peer review under responsibility of The Gulf Organisation for Research and Development.
Production and hosting by Elsevier
2212-6090 2013 The Gulf Organisation for Research and Development. Production and hosting by Elsevier B.V. Open access under CC BY-NC-ND license.
http://dx.doi.org/10.1016/j.ijsbe.2013.05.001
M.S. Imbabi et al. / International Journal of Sustainable Built Environment 1 (2012) 194216
2.1.
2.2.
2.3.
2.4.
3.
4.
5.
Classification of Portland cements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydration of Portland cements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
World Portland cement production. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current energy use and CO2 emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1. Quarrying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2. Pyroprocessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.3. Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.4. Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5. Future CO2 emissions if we continue business-as-usual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Novel, resource efficient cements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1. Alternative fuel substitutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2. Commonly used Supplementary Cementitious Materials (SCMs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1. Ground limestone cement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2. Fly ash and pulverized fuel ash (PFA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3. Ground granulated blast furnace slag (GGBS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4. Silica fume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3. Novel, resource efficient cements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1. Calcium sulfoaluminate cement (4CaO3Al2O3SO3, Ca2SiO4, C2(A,F)) . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2. Calcium aluminate (CaAl2O4) and calcium aluminasilicate cements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3. Super-sulfated cements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.4. Magnesium-oxide based cement as a carbon negative cement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.5. Alkali-activated cements/geopolymers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.6. Sequestrated carbon cement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current and projected economics of cement production . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1. UK production and price indices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2. US production and price indices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3. Qatar production and price indices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4. Saudi Arabian production and price indices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5. Comparison of price trends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6. Projections of future economic factors governing cement production . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conclusions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Introduction
Concrete is a basic building material that will continue to
be in demand far into the future. A world without concrete,
and its dominant precursor, Ordinary Portland Cement
(OPC), is hard to imagine. Although there are dierent types
of concrete that have been developed for use in dierent
applications, their common virtues are familiarity, versatility, strength, durability, wide availability, re resistance,
resistance to the elements and comparatively low cost.
OPC is a vital construction material and also a strategic
commodity (Vlasopoulos, 2010). Such is our dependence on
OPC that the world currently produces nearly 3.6 billion
metric tonnes of the material each year (USGS Mineral
Commodities Summary, 2012), with volume predicted to
rise to more than 5 billion metric tonnes by 2030 (Muller
and Harnisch, 2008; OECD/IEA and World Business
Council for Sustainable Development, 2009). Although
gures vary from country to country, around half of the
worlds OPC is used to make around 11 billion metric
tonnes of concrete annually; the rest is used in mortars,
screeds, stucco, coatings, soil stabilization and other applications. (New Zealand Cement Holdings, 1988; Smith et al.,
195
197
197
198
198
200
200
201
202
202
202
203
204
204
204
204
205
205
205
206
206
206
207
207
207
207
209
210
210
210
212
214
215
2002). Today, the OPC market is dominated by China,

which is attributed to 57.3% of global consumption (CEMBUREAU, 2012).
The cement industry, like the rest of the construction
industry, is facing unprecedented challenges relating to
energy resources, CO2 emissions and the use of alternative
materials. Worldwide, the cost of energy is rising inexorably as fuel sources deplete. This has clear, traceable
impacts on the cost of producing cement and its market
price; Green taxes are an additional cost that is incurred
if emissions are not restricted, potentially leading to a
doubling in the price of cement by 2030 (OECD/IEA
and World Business Council for Sustainable Development, 2009).
Despite the incremental improvements in process eciency that have been adopted by the cement industry in
recent years, OPC production is still responsible for around
6% of all man-made global carbon emissions. The Cement
Sustainability Initiative, developed by the World Business
Council for Sustainable Development, brings together the
major cement producers from across the world to try and
tackle this problem (OECD/IEA and World Business
Council for Sustainable Development, 2009). An important
196
part of the initiative is a database showing CO2 emissions

and energy performance gures for many of the signicant
players in the global cement industry, to promote the sharing of ideas aimed at improving these values.
The push to reduce global CO2 emissions is backed by
governments and corporations who understand that the
present rate of release of this greenhouse gas into the
atmosphere is a serious threat to future life and prosperity
on the planet. Various authorities have introduced legislation and incentives (tax rises such as CO2 taxes, quarrying
and extraction tax, etc.) in order to regulate and reduce
the activities of the industrial sectors most responsible
for greenhouse gas emissions. However, the rate of
increase in emissions continues almost unabated as a
result of population growth and increased industrialization and economic activity in developing countries, notably in Latin America, Africa, the Middle East, India
and developing countries in Asia where a three to fourfold
increase in demand is projected by 2050 (OECD/IEA and
World Business Council for Sustainable Development,
2009).
If the cement and concrete industries are to become sustainable and eectively contribute to emission reduction
then, in addition to improvements in process eciency
and reliance on OPC blends incorporating waste materials,
moving to less carbon intensive fuels, developing clinker
substitutions employing other low carbon materials with
cementitious properties and new low carbon and carbonreducing cement formulations and production processes
are needed.
Carbon-reducing cements, if they could be developed for
commercial-scale application, probably oer the safest,
most economical and elegant Carbon Capture and Storage
(CCS) technology. Other approaches to CCS that require
piping CO2 emissions from cement production (and other
polluting sources such as power generation), are viewed
by some as the best way forward. However, widespread
concerns relating to long-term reliability and high capital
cost suggest that ideas such as pressurized, pumped storage
of liqueed CO2 in geological formations may be neither
technically nor commercially viable. They cannot be relied
on to provide a permanent solution as the risk of containment failure is simply too great.
In order to appeal to major cement manufacturing companies, an alternative cement product has to be able to generate at least the same economic value as that from an OPC
production plant. At 7.6% of world cement production, the
cement industry in Europe represents around 56,000 direct
jobs. The average cement plant will produce around 1 million tonnes of cement per annum and cost around 150 million. Advances in automation mean that a modern plant is
usually manned by less than 150 people (CEMBUREAU,
2012). Each tonne of OPC produced requires 60130 kg
of fuel oil or equivalent, depending on the cement variety
and the process used, and about 110 KWh of electricity.
This accounts for around 40% of the average 0.9 tonnes
of CO2 emissions per tonne of cement produced, with the
rest attributed to the calcination process, other manufacturing processes and transportation.
Concretes, on the other hand, refer to mixtures comprising coarse aggregates (such as crushed rock, ranging
in size from 5 to 20 mm), ne aggregates (such as sand,
ranging in diameter from 63 microns to 5 mm) and a
cement binder. When mixed with appropriate quantities
of water and (where required) performance-enhancing
admixtures, this produces an initial uid phase that can
be shaped or cast and sets to produce a solid phase comprising a very strong, rigid concrete element or structure.
Conventional Portland-clinker-based hydraulic cements
(products of the calcination process) use source-materials
that are cheap and abundant almost everywhere. Finding
suitable alternative cements would require an investigation
into their cost and protability as well as their structural
characteristics.
As alternative low-carbon cements and concretes enter
the equation, three conditions will determine their success
or otherwise; rstly that they are useable and perform well
both short term and long term, secondly that there is sucient information validating the capabilities of the product
so that they meet engineering standards for specic functions, ranging from the making of cavity blocks to readymix for in situ casting of foundations, and thirdly, that
there is sucient raw material that can be transported in
bulk to processing plants.
Although the ingredients for making cement are readily
available in most countries, there may be opportunities to
use locally sourced specic raw materials such as industrial
waste, recyclable material or even earth. These materials
must of course have controlled characteristics and
properties that are suitable for purpose, whether it is for
blending ground granulated blast furnace slag for strength
enhancement or soil for producing compacted earth blocks;
from the point of view of the engineer or architect, such
materials are generally selected on the basis of the
added functionality that they oer and their costeectiveness.
The present paper examines the production of OPC (the
benchmark cement against which all cements are measured) and applicable standards. It will summarize the
waste substitutes that are currently being used to reduce
the carbon footprint of a range of Portland-based cements.
Co-incineration of waste-derived fuels (municipal waste,
sewage sludge, animal meal, waste by-products, etc.), to
reduce emissions and eectively dispose of these wastes,
will also be briey discussed. Some traditional replacement
cements will be briey discussed, and the emerging, next
generation of green alternative cements such as Calcium
Sulfoaluminate (C$A) cement, successfully developed and
used in China since the 1970s, will be introduced.
The paper will conclude with a look at current and projected future demand for cement, highlighting the main
players. A preliminary analysis of the economics of low
carbon cements will be carried out and a valuation method
for the carbon reduction benets they oer is proposed.
2. Portland-based cements and other hydraulic binders

Ordinary Portland Cement (OPC) is the dominant contemporary cement. It is a mixture of compounds produced
by burning limestone and clay together, in a rotary kiln, at a
temperature of around 1,450 C. Approximately 40% of
cement plant CO2 emissions are from the burning of fossil fuel
to operate the kiln, 50% due to the manufacturing process and
the remaining 10% are accounted for by indirect CO2 emissions relating to transportation of the nished product and
front-end production processes (World Business Council
for Sustainable Development, 2012; Hendriks et al., 1999).
Cement has been used for millennia; the earliest known
use of hydraulic binder was by the Macedonians of ancient
Greece, and by the ancient Egyptians and Romans. The
rst forms of clinker-based hydraulic cements contained
basic calcium compounds, for which the major raw materials are limestone (calcium carbonate) and clay (silicon
oxide compounds). Calcination (from the Latin word calcinare) is the decomposition of calcium carbonate (limestone) to calcium oxide (lime) in order to produce basic
cement. The product of calcination is usually referred to,
in general, as calcine, regardless of the minerals undergoing thermal treatment. In the cement business it is called
clinker. The calcination process for a typical modern
cement clinker, where calcium carbonate and silicon oxides
are combined at elevated temperature (1,450 C), is:
3CaCO3 SiO2 ! Ca3 SiO5 3CO2
calcium silica heat calcium carbon
carbonate
silicate dioxide
clinker
This produces a powder that will react with water and

change from a paste or liquid solution into a solid mass.
The ner the cement clinker is ground, the faster the reaction will be due to the increased surface area of the cement
powder in contact with water.
Table 1
The primary constituents of a modern Portland cement nished clinker.
Tricalcium silicate
Dicalcium silicate
Tricalcium aluminate
Tetracalcium
aluminoferrite
Gypsum
50%
25%
10%
10%
Ca3SiO5 or 3CaOSiO2
Ca2SiO4 or 2CaOSiO2
Ca3Al2O6 or 3CaOAl2O3
Ca4Al2Fe2O10 or 4CaOAl2O3Fe2O3
5%
CaSO42H2O
197
Portland cements are the most common CalciumSilicateHydrate (CSH) hydraulic cements in use today.
The rst Portland cement was originated by the English
bricklayer Joseph Aspin in Leeds in the 1800s, after he
had experimented with earlier types of cement such as
Roman and other Natural cements. The composition of a
typical Portland cement is 65% calcium oxide; the rest
is generally a mixture of aluminum, iron and silica.
Table 1 below lists the ve main chemical compounds
in cement and their average percentages by weight. These
compounds develop from limestone or lime and clay as a
consequence of pyroprocessing. Most hydraulic cements
are based on basic calcium compounds that are easily
hydrated (Gartner and Macphee, 2011). Limestone is
based mainly on calcium carbonates. Alumino-silicates
and calcium sulfates may be found in clay but more usually calcium sulfate has to be added directly to ground
clinker.
2.1. Classication of Portland cements
In the UK and Europe the applicable standard is BS EN
197 (BSI, 2011). This is summarized in Table 2.
The pozzolans are separated into articial pozzolans
such as y ash, silica fumes and GGBS, and natural pozzolans composed of calcium, silica and aluminum compounds
such as volcanic ashes, calcinated clay and shale. Considerable latitude is permitted when specifying the amount of
each pozzolan used, as can be seen in Table 3.
The American Society for Testing and Materials
(ASTM) adopted a somewhat dierent approach when it
established the C150 standard specication recognizing
the 5 classications/10 types of Portland cement listed in
Table 4 (ASTM, 2012).
2.2. Hydration of Portland cements
Cement requires clean water to hydrate eectively. The
hydration process in concrete involves the cement compounds undergoing a chemical reaction with water to produce a stable, amorphous solid hydrate. This solid phase
continues to grow and expand in the presence of water
and cohesively encapsulates other materials inside the
matrix of hydrate solid. The chemical reaction in cement
saturates the water with calcium (Ca) and hydroxide
(OH) ions. The negative hydroxide ions raise the alkalinity
of the cement paste to a pH > 12, eectively creating a cor-
Table 2
Classication of cement types according to BS EN 197-1:2011.
CEM I Portland cement
CEM II Portland composite
cement
CEM III blast furnace cement
CEM IV pozzolanic cement
CEM V composite cement
Portland cement and up to 5% of minor additional constituents (the original OPC)

Portland cement with up to 35% of other Supplementary Cementitious Material (SCM) such ground limestone, y ash
or Ground Granulated Blast furnace Slag (GGBS)
Portland cement with a higher percentage of blast furnace slag, usually around 60% to 75%
Portland cement with up to 55% of selected pozzolanic constituents
Portland cement blended with GGBS or y ash and pozzolanic material
198
Table 3
Standard cements according to DIN EN 197-1, EN 197-4 and DIN 116410.
Portland cement clinker
Blast furnace slag
Natural pozzolan (trass)
Sulfate (gypsum/hemihydrate/anhydrite)
Cement additives
5100 mass%
695 mass%
655 mass%
09 mass%
<1 mass%
rosive, alkaline substance. As the water becomes saturated

with calcium and hydroxide ions, solid calcium hydroxide
and calcium silica hydrate solids form to precipitate from
the solution into the pore spaces. This process also produces heat.
2Ca2 SiO4 5H2 O ! 3CaO2 SiO2 4H2 O CaOH2
dicalcium
silicate
water
phase 2
cement
water
calcium
hydroxide
The end products are the same for dicalcium and tricalcium silicates when mixed with water. The rapid reaction of
tricalcium silicates in water produces more heat than the
slower reaction of the dicalcium silicates in water; however
both reactions produce calcium hydroxide and calcium-silicate-hydrate molecules and heat.
2Ca3 SiO5 7H2 O2 ) 3CaO2 SiO2 4H2 O 3CaOH2
tricalcium
silicate
Water
Calcium
silicate hydrate
calcium
hydroxide
The main bond mechanism is not capillary force, as is

often assumed, but a combination of the interlocking
mechanism of microscopic hydrate solid and internal pressure due to the volume lling eect associated with the
conversion of liquid water into a solid hydrate phase and
increasing the solid volume (Gartner and Macphee,
2011). The binding capacity of a hydraulic binder is thus
related to the fact that the new solid phases can precipitate
from a supersaturated aqueous solution in such a way as to
create a signicant area of solidsolid bonding interfaces in
a volume that was previously lled with liquid water. A key
factor governing the selection of compounds for cement is
the rate at which they can hydrate. By blending these compounds an optimum hardening rate and nal strength for a
specic use can be empirically determined.
Due to the nature of cement, there can be large deviations between design strength and the strength of concrete
in situ; it is common practice to perform tests for such
material on site or during the construction phase. Aggregates partially act as reinforcement for the hardened matrix
of cement and also reduce cost by replacing a large volume
of expensive cement with something similar, but of dierent
load-bearing strength. In this sense the primary function of
cement is to hold together or bind together the aggregate
load bearing materials.
2.3. World Portland cement production
The production of cement varies greatly from nation to
nation with the availability of materials. Where production
does not satisfy demand a country can import to meet its
needs. A review of recent trends in the global production
of cement shows that the estimated amount of cement produced over the world was 3.6 billion tonnes see Fig. 1,
which shows that China dominates most of the market followed by Asia (CEMBUREAU, 2012). Typical cement
plant capacity is expected to remain in the range of 1.5
and 2.5 million tonnes per annum (Schneider et al., 2011).
Fig. 2 shows global cement production increasing constantly from 1990 to 2050. This is to be expected as it is
the second most consumed product on the planet after
water. The industry is growing particularly rapidly in
developing countries such as India and China that have a
high demand for infrastructure and housing (World Business Council for Sustainable Development, 2009).
In the UK, cement production feeds into durable products and applications in the proportions shown in Fig. 3
(Smith et al., 2002). Articles of cement and concrete include
products such as concrete building blocks and bricks, tiles,
pipes, etc.
2.4. Current energy use and CO2 emissions
Approximately 3.6 billion tons of cement is produced
globally every year. A conservative estimate for every
Table 4
Classications and types of Portland cement according to ASTM C150/C150 M.
Type I and type IAa
Type II and type IIAa
Type II (MH) and type II
(MH)Aa
Type III and type IIIAa
Type IV
Type V
a
General purpose cements suitable for all uses where the special properties of other types are not required (the
original OPC)
Type II cements contain no more than 8% tricalcium aluminate (Ca3Al) for moderate sulfate resistance.
Type II (MH) cements have moderate heat of hydration characteristic, based on a requirement that the sum of
Ca3Si + 4.75 Ca3Al < 100% (tricalcium silicate and tricalcium aluminate), and moderate sulfate resistance
properties based on a maximum Ca3Al2O6 content of 8%.
Chemically and physically similar to type I cements except they are more nely ground to produce higher early
strengths.
Used in massive concrete structures where the rate and amount of heat generated from hydration must be
minimized. It develops strength more slowly than other cement types.
Contains no more than 5% Ca3Al2O6 for high sulfate resistance.
The A sux refers to cements used to make air-entrained concrete and containing an air-entraining agent.
Europe (excl
CEMBUREA)*
0.3%
CEMBUREAU
Oceana
7.3%
0.3%
CIS
2.5%
199
America (excl USA)

5.2%
USA
1.9%
Africa
4.7%
China
57.3%
Asia (excl China,

India, Japan)
12.9%
India
6.2%
Japan
1.4%
*Excluding EU27 countries not members of CEMBUREAU
Figure 1. World Portland cement production today.
(Mt / year produced: Records and estimates)

6000
Projected
5000
Other developing
countries
Mt / year
4000
India
3000
2000
China
1000
OECD, other
industrial nations
and transition
economies
0
1990
2000
2010
2020
2030
2040
2050
Figure 2. World Portland cement production 19902050.
1 kg of cement produced gives a by-product of 0.9 kg of

carbon dioxide (Hendriks et al., 2004), this equates to
3.24 billion tonnes of CO2 per year. These gures do not
include CO2 and other green house gasses emitted during
the quarrying and transport of raw materials or the loading, unloading and transportation of the cement produced.
The main sources of emissions in the OPC manufacturing process are in two parts:
(i) From the calcination process as described earlier.
(ii) From the combustion fuel used to heat the raw materials to sintering temperatures (14001600 C). The
amount of CO2 emission depends on the type of fuel
and the particular processing method used. Kilns are
red using coal, fuel oil, natural gas, petroleum coke,
biomass, waste-derived alternative fuels or mixtures of
these fuels. The theoretical heat requirement for clinker-making is calculated to be about 1.75 0.1 MJ
per kg; however; process ineciencies mean the actual
heat requirements are higher (Hendriks et al., 2004;
Norchem, 2011).
200
Firbre cement
0.09%
Factory made mortars

1.70%
Cement clinker
13.09%
Cements
13.77%
Ready mixed
concrete
45.95%
Lime
1.31%
Plasters
0.96%
Articles of cement
and concrete
21.03%
Plaster products for
construction purposes
2.10%
Figure 3. Cement, concrete and plaster products in the UK construction market.
The production process is diagrammatically shown in

Fig. 4 (Association of Cementitious Material Producers,
2010) and the key stages are described in the rest of the
section.
2.4.1. Quarrying
The production of Portland cement begins with the
quarrying of raw materials. Most cement plants are situated near a limestone quarry to minimize transportation
costs. Quarrying limestone involves drilling, blasting, excavating as well as crushing, screening and storing. The raw
materials are milled together to achieve the right composition before being sent to the kiln for pyroprocessing. Only
the operation of machinery is responsible for CO2 emissions when quarrying for raw materials.
2.4.2. Pyroprocessing
Cement clinker is made in a rotary kiln, or long cylindrical rotary furnace that turns around once or twice every
minute. Temperatures are generally around 14001600 C,
and energy demand varies depending on the manufacturing
process (Norchem, 2011). The material undergoes the process known as calcination inside the kiln after all moisture
is evaporated out, about a third of the way down the kiln.
The end product size ranges from dust to big lumps of calcium silicate or clinker. See Table 5 for CO2 emissions in kg
per kg cement produced for various fuels and various
clinker/cement ratios (Assumptions Electricity use is
0.38 MJe/kg of clinker; the average emission factor of
CO2 of electricity production is 0.22 kg/MJe; fuel use is
3.35 MJ/kg of clinker (dry process) and 5.4 MJ/kg of
Figure 4. Share of total CO2 emissions across the Portland cement production process.
201
Table 5
CO2 emissions in kg per kg cement produced for dry and wet cement production process for various fuels and various clinker ratios (Hendriks, 2004).
Clinker ratioa (%)
Calcination process
55
75
(Portland) 95
0.28
0.38
0.49
Dry kiln process
Wet kiln process
Coal
Oil
Gas
Waste
Coal
Oil
Gas
Waste
0.55
0.72
0.89
0.50
0.66
0.81
0.47
0.61
0.75
0.36
0.47
0.57
0.67
0.88
1.09
0.59
0.77
0.95
0.53
0.69
0.90
0.36
0.47
0.57
The ratio of Portland cement clinker to additives.
Figure 5. Energy eciency in clinker production (Oda et al., 2012).
clinker (wet process)). It should be noted these gures

assume that no CO2 penalty is attached to materials such
as slag or y ash and some may argue they are therefore
highly articial, erring on the optimistic.
The plot in Fig. 5 spans a range of thermal energy eciencies in Portland cement clinker production, from lowest to highest energy consumptions based on type and
capacity of kiln.
According to the CSIs Getting the Numbers Right
(World Business Council for Sustainable Development,
2009), the dry manufacturing process with preheaters and
pre-calciner technology, used in a large number of cement
production plants globally, had an average specic energy
consumption of 3,605 MJ/t clinker in 1990 but saw a
reduction of around 6% by 2006. Energy eciency is the
only element that can be managed by the industry itself
but there are many factors that make this dicult. Upgrading existing plants with new technology is a costly process.
If high cement performance is required, the grinding of
very ne granules (for high specic surface area) will
require greater power consumption. Using clinker substitutes may reduce calcination CO2 emissions but will generally require more heat energy. Products such as GGBS or
y ash can be used to substitute clinker in cement production either before (limited by the low lime content of the
additives) or after calcination (OECD/IEA and World
Business Council for Sustainable Development, 2009),
however, there are limitations to this process such as availability or cost of the clinker substitute materials and there
are also barriers imposed by standards and regulations.
2.4.3. Grinding
The lumps of clinker are ground up with calcium sulfate
dihydrate (CaSO42H2O) or gypsum or active anhydrite to
control the rate of hardening or the setting time (gypsum is
also used to make Plaster of Paris, a commonly used rendering plaster). Usually about 210% of the ground-up
Portland cement is gypsum. The nal product, OPC
cement is used in various ways, primarily to make mortar
and concrete, cinder or cavity block.
202
Figure 6. Projected global cement industry reference CO2, million metric tonnes (Battelle, 2002).
2.4.4. Transportation
The cost of transporting bulk commodities greatly
aects cement production. As a result, cement production
plants are often located at or close to limestone quarries
and customers tend to purchase cement and ready-mix concrete from as local a source as possible. Nearly 98% of U.S.
cement and all readymix concrete are shipped to customers
by truck (Hendriks et al., 2004). Readymix trucks typically
have a carrying capacity of 68 cubic meters of concrete
each. Barge and rail modes account for the remaining distribution. Exported cement is invariably transported by
land or sea. The estimated emission rates of transport by
truck, rail and ship are, respectively 0.033, 0.017 and
0.010 kgCO2/tonne-kilometer (Lawson, 2007).
under 2 billion tonnes of CO2 per year in 2010 and 4.8 billion tonnes of CO2 per year in 2050. The CO2 emission
today (i.e., in 2012) is 3.24 billion tonnes of CO2 per year.
The original predictions have therefore underestimated the
increase in CO2 emissions by 124% i.e., 2.24 billion as
opposed to 1 billion tonnes CO2 per year. If the exponential trend assumed in the original prediction is adjusted
to accommodate the 2012 data and extrapolated over the
same period of time, the cement industry emissions could
conceivably rise to around 32.7 billion tonnes of CO2 per
year, more than 6 times projected and a massive 33 times
1990 levels. This would be very bad news indeed and so
must clearly never be allowed to happen.
3. Novel, resource ecient cements
2.5. Future CO2 emissions if we continue business-as-usual

The Cement Sustainability Initiative (OECD/IEA and
World Business Council for Sustainable Development,
2009) recommends how the industry can make changes
on a global scale by promoting the best available eciency
technologies for new and existing production plants,
increasing awareness of alternative fuels and encouraging
clinker substitution. Their recommendations also include
initiation of government support programmes that will
help fund new industry pilot projects. Fig. 6 shows the projected CO2 emissions from the cement industry if no
changes are made to current production methods. By
2050 the emissions will have increased by almost 5 times
the value in 1990. This is not a good path to be on when
the world is becoming more green-aware. These initiatives
will thus not only help pave the way for a greener cement
industry but will also be benecial in reducing greenhouse
gas taxes and ensuring the continuation of the industry in
an economic climate of ever increasing costs.
The predictions in Fig. 6 were made in the year 2000 and
suggest CO2 emissions rising from around 1.4 billion to just
In order to improve energy eciency and reduce carbon

emissions, the approaches that have been adopted can be
summarized under the following four main headings:
{Review and update of manufacturing processes}
Manufacturing processes in cement production have
been and continue to be optimized and automated, using
the best technologies available to reduce cost, emissions
and increase productivity. This has led to incremental
reductions in Green House Gas (GHG) emissions and
has also reduced the industrys employment levels (Taylor
et al., 2006). Review and update of the manufacturing process lie rmly within the domain of cement manufacturers,
cement production equipment manufacturers and cement
plant designers and are not for discussion here.
{Co-incineration of waste material in cement kilns}
Co-incineration of waste fuels such as wood and plastics from demolition activities, rubber tires, industrial
and municipal sewage sludge, animal wastes (fats,
carcasses, etc.), agricultural waste, solid waste, solvents
and oils is a booming industry in some European
countries, notably Germany (Joint Research Centre,

2012). The benets are: less conventional energy demand
and cost overheads, funds paid to cement producers for
disposal of waste materials that would otherwise go to
landll, and disposal of these wastes to reduce landll.
The disadvantages are increased CO2 emissions and
release into the atmosphere, if not properly (and expensively) managed, of hazardous materials like sulfur dioxide
(SO2) and other sulfur compounds, total organic compounds (TOC) including volatile organic compounds
(VOCs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD and PCDF) and metals (including
Hg, Cd, As, Pb) and their compounds. With the exception
of waste biomass alternative fuels, which if used can deliver a net CO2 emission reduction, co-incineration of waste
products addresses a dierent sustainability agenda (management of waste).
{Supplementary Cementitious Materials (SCMs) in
cement production}
This relates to the development of new concrete design
guidelines that allow more SCMs to be used, to reduce
CO2 calcination. SCMs include (a) ground limestone as a
ller to replace Portland cement and reduce carbon emissions, or (b) natural or articial mineral pozzolanic compounds (Bentz, 2011). Articial pozzolans are byproducts of the iron and steel industries, classied as
Recovered Mineral Components (RMCs). The benets of
adding small quantities of ground limestone are well documented (Matschei et al., 2007) and the CEM I standard
permits up to 5% by weight of ground limestone to be
added to the mix without loss of quality. The CEM II/AL and CEM II/B-L standards for Portland limestone
cement are more liberal and permit the substitution of
up to 20% and 35% by weight, respectively of ground limestone and other SCMs (CEMBUREAU, 1991).
{The development of novel, resource ecient cements}
Novel cements involve development of cement manufacturing processes that use dierent raw materials. The
shared aim of novel cement developers is cement that
emits less CO2 and requires less energy to produce than
CEM1, without reducing or compromising the eciency
of the cement. Novel cements would ideally use waste
derived fuels and raw materials (Mineral Products Association, 2012). The chemical properties of some novel
cements may be similar to those of Portland cement, making them ideal (easy) potential alternatives. Low carbon
cements are either only in use on a limited scale in a
few parts of the world, for example Calcium Sulfoaluminate Cement (C$A) in China (Lafarge has announced
they will be marketing their Aether C$A cement in
2014), or they are being developed by small start-up companies still looking to build pilot plants. A major objective is therefore to verify and establish technical and
commercial viability, and their sustainability against Portland cements.
203
The remainder of the section will touch on alternative

fuels and expand on the use of SCMs and development
of novel, resource ecient cements.
3.1. Alternative fuel substitutes
The ring of cement clinker kilns is traditionally fueled
either by coal or petroleum coke, or, to a lesser extent,
alternatively by natural gas or fuel oil. Use of other fuels
such as biomass can be an eective fossil fuel substitute,
producing CO2 emissions that are about 2025% less than
those of coal (OECD/IEA and World Business Council for
Sustainable Development, 2009). Not only do reduced
emissions make such fuels suited for cement kilns, but combustion products of inorganic compounds such as ash are
also integrated into and can contribute benecially to the
clinker product.
The full range of alternative fuels used by the cement
industry includes used tyres, sewage sludge, waste oil and
waste derived fuels such as paper residue, plastics and textiles. Cement kilns are able to use whole or shredded tyres
as a fuel, the biggest use for discarded tyres in Japan and
the USA. The use of such alternative fuels in the production of Portland cement clinker is possible but it can inuence the clinker properties as these fuels burn dierently
compared to traditional fossil fuels. This can change the
temperature prole in the kiln and also aect the cooling
conditions. The result is an alteration in the characteristics
of the clinker that can be attributed to the porosity of the
granules, burning grade of the clinker or the crystal size of
the clinker phases or their reactivity.
Wastes can also alter the cement composition. For example, when tyres are co-incinerated the zinc oxide content of
clinkers increases signicantly. The burning of alternative
fuels thus introduces dierent components into the kiln via
ash. These can aect the performance characteristics of the
cement, such as lower early strength and longer setting times
(Schneider et al., 2011). However, these problems can be
overcome by closely monitoring and adjusting the production process and materials to allow for the correct level of
alternative fuels being burnt to be calculated and making
the required compensatory changes to the composition of
the raw materials fed to the kiln. This will produce high quality Portland cement clinker that conforms to cement standards. In many countries the use of alternative fuels has
moved from laboratory to application (Mineral Products
Association, 2012). In some European countries the average
substitute rate is about 70%; in the UK it is only about 40%.
The achievement of high substitution rates faces legal
and political barriers. In the UK the cement industry is primarily regulated by the Environmental Permitting Regulations (EPR) for England and Wales and Pollution
Prevention and Control (PPC) for Scotland. In order to
burn waste derived non-fossil fuels, a license or permit
needs to be granted. To obtain this an environmental assessment has to be carried out to determine if the use of such
204
waste will be of greater or lesser impact than using traditional resources. However, the use of waste derived alternative fuels will generally see an increase in the associated CO2
costs. It is likely to become dicult for the industry to
source signicant quantities of biomass at acceptable prices.
The IEAs predictions suggest that it will only be economically viable for the cement industry to use biomass sourced
alternative fuels until 2030 (OECD/IEA and World Business Council for Sustainable Development, 2009).
Alternative fuel trials such as those at Lafarges Aberthaw Works in the UK using Meat and Bone Meal
(MBM) are seeking to explore the commercial and environmental benets that using dierent alternative fuels can
bring (Lafarge Cement UK, 2011). The plant has also used
end of life tires and solid recovered fuel as a partial replacement for traditional fuels. They hope to continue using
these alternative fuels on a permanent basis given the
numerous benets. Using alternative fuels may, however,
be only a temporary short lived solution. In the long run
a more permanent solution must be found.
3.2. Commonly used Supplementary Cementitious Materials
(SCMs)
SCMs are used either as llers or because of their pozzolanic properties. This means that the SCM particles will
hydrate just as Portland cement does, but they also supply
more silicate in the mixture that will react with excess
hydrated lime released during the hydration of the Portland
cement. In this section the most common SCMs are reviewed.
3.2.1. Ground limestone cement
Hawkins et al. (2003) presented a thorough and comprehensive review of research into the use of blended or interground limestone in Portland cement. This looked at the
eects of limestone use on particle size distribution, grinding,
workability, hydration and setting of the cement including
reaction chemistry and kinetics, heat generation, microstructure, setting time, durability, etc. Portland Limestone Cement
(PLC) has been used in Europe for more than 25 years, often
as an alternative to OPC in applications that do not require
sulfate resistance (even though some tests have shown
improved sulfate resistance for cements containing limestone). Limestone is a low cost, readily available material that
is easier to grind than clinker and leads to improved particle
packing and hydration. .It improves workability and reduces
bleeding in PLC compared to OPC, but its main attributes
are reduced cost and reduced CO2 emissions. PLC containing
up to 20% limestone, manufactured in accordance with current standards, can reduce energy requirements and carbon
emissions by as much as 10% compared to other Portland
cements while delivering comparable performance (Portland
Cement Association, 2013).
3.2.2. Fly ash and pulverized fuel ash (PFA)
Fly ash and PFA are essentially one and the same; it
is ash produced from coal and some other solid fuel
combustion systems. Where bottom fuel ash is left in the

region of combustion, ne grained y ash is carried with
combustion u gases and commonly collected by electrostatic precipitation. The chemical composition of y ash
tends to be a heterogeneous mixture of silicon oxides
(SiO2), aluminum oxides (AlO3) and iron oxides (Fe2O3,
Fe3O4) Bentz, 2011. Such ash types are common in Europe
but in many parts of the world, lime-rich ashes are available.
Because of its pozzolanic properties, y ash is often used
to replace typically 30% of the mass of Portland cement in a
concrete mix, for example to lower permeability and reduce
initial heat evolution. The y ash type used is limited to a
Class-C and Class-F types. The classication as C (calcium
rich) or F (aluminosilicate rich) types has been abandoned
by ASTM, although the terms are still widely used. Even
these two classes have wide range specication limits that
are dependent on variability of source. Ensuring consistency
is therefore a major concern among cement suppliers and
standards typically require that each batch of cement uses
SCMs from the same source. Fly ash will contribute to the
strength of concrete after seven days of curing. Strength
development of y ash in concrete is due to a chemical reaction between the y ash and calcium hydroxides produced
by hydration of OPC (Mahasenan et al., 2003).
The main documents controlling the use of PFA are the
Manual of Contract Documents For Highway Works, Volume 1, Specication For Highway Works, Series 1700
Structural Concrete (Highway Agency, Department for
Transport), BS 3892: 1993 Pulverized-fuel ash. Specication for pulverized-fuel ash for use with Portland cement,
ASTM C618-01 Standard Specication for Coal Fly Ash
and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Concrete and BS EN450-1: 2012 Fly ash
for concrete. Denition, specications and conformity
criteria.
3.2.3. Ground granulated blast furnace slag (GGBS)
This is a by-product of the iron and steel industry; while
pig iron is extracted from melted raw iron ore, the left-over
material (which oats to the top) is referred to as slag. It
consists of calcium, magnesium aluminosilicates and also
has pozzolanic properties depending on quenching history.
Also depending on the cooling method used, there are three
main types of blast furnace slag: air cooled, granulated and
expanded slag. Granulated slag is formed by quickly
quenching molten slag with water. The result is glassy
sand-like material that, when ground to a ne powder
and contacted with alkali such as lime or Portland cement,
develops strong hydraulic cementation properties (van Oss
Hendrick, 2012).
Expanded slag and air cooled slag are primarily used as
an aggregate in concrete and bitumen applications but
when ground into a ne powder, can also be used as
supplementary cementitious materials similar to GGBS
(provided a high proportion of the glass is preserved).
However all slag, including some steel furnace slag (SFS),
can be used as raw feed material for cement clinker manu-
facture in a kiln. Reductions in CO2 are signicant due to

the process being less energy intensive and involving less
heat to perform the calcinations process.
The main documents that control the use of GGBS in
cement are the Manual of Contract Documents For Highway Works, Volume 1, Specication For Highway Works,
Series 1700 Structural Concrete (Highway Agency, Department for Transport), BS 6610:1991 Specication for Pozzolanic pulverized-fuel ash cement, ASTM C595-02a
Standard Specication for Blended Hydraulic Cements,
BS EN 197-4: 2004 Cement. Composition, specications
and conformity criteria for low early strength blast furnace
cements, and BS EN 197-1 Cement. Composition, specications and conformity criteria for common cements.
3.2.4. Silica fume
Silica fume, also known as microsilica, is a by-product
of the production of silicon and silicon alloys in electric
arc furnaces. It is added to cement to produce high performance concretes that are much stronger and more durable
than other concretes made using blended cements; it is also
very useful for reducing the permeability of concrete and
therefore able to better protect steel reinforcement. A problem with silica fume is that it greatly increases water
demand so many codes limit addition to 6% unless the
mix is heavily superplasticized. Unfortunately, where silica
fume was once a cheap waste product, it is now an expensive high performance cement supplement primarily used in
bridges and other exposed structures that require high
weathering performance.
Using silica fume will contribute incrementally to reducing CO2 emissions but it is not as easy to obtain as other
recovered mineral components (RMCs) such as GGBS
and y ash. The production process is very energy intensive
but these values attribute zero CO2 to the fume as it is a byproduct of another manufacturing process. According to
the U.S. Environmental Protection Agency 1 lb of CO2 is
avoided for every 2.2 lbs of SCM substituted in a cement,
or 0.432 kg of CO2 per kg of SCM (Norchem, 2011).
The standards documents that control the use of silica
fume in cement are ASTM C1240-12 Standard Specication for Silica Fume Used in Cementitious Mixtures and
BS EN 13,263 1:2005 + A1:2009 Silica fume for concrete. Denitions, requirements and conformity criteria.
3.3. Novel, resource ecient cements
{Limestone-based novel cements}.
3.3.1. Calcium sulfoaluminate cement (4CaO3Al2O3SO3,
Ca2SiO4, C2(A,F))
Calcium Sulfoaluminate (C$A) cements are manufactured and have been used on an industrial scale in China
since the late 1970s. The cement powder is formulated to
contain yeelemite, Ca4Al6[O12SO4]. Belite-calcium sulfoaluminate ferrite C$A clinkers can produce cements with
similar performance to Portland cements while in principle
205
being manufactured in conventional Portland cement

plants to deliver signicantly less CO2 emissions during calcination. They also require less heat compared to Portland
cements, further reducing CO2 emissions. C$A clinker can
be readily synthesized with a high content of yeelemite,
ranging from 35% to 70% mass and substantial amounts
of belite and ferrite phases, when limestone reacts along
with other materials or waste products. C$A cements are
manufactured in a process similar to that of Portland
cement in a dry process rotary kiln at temperatures
between 1250 and 1350 C. C$A cement compositions are
in structural grades with phase contents of 3570% yeelemite, 30% belite and 1030% ferrite (Calcium Ferro Aluminate) (Mineral Products Association, 2012).
As with Portland cement, gypsum is added in a controlled process in optimized amounts and ground with clinker to form dierent types of C$A cements. The properties
of C$A cement change from rapid hardening cement to a
shrinkage compensated cement when increasing amounts
of gypsum are added and it will eventually become expansive and hence self-stressing at suciently high sulfate
(Sharp et al., 1999). C$A cement as supplied provides
acceptable setting times and good strength development.
This is achieved by a process based on the rapid formation
of ettringite and variable quantities of amorphous gel
phase. C$A cements have a strength development similar
to if not greater than Portland cement, with an early
strength of between 35 to 55 MPa after one day, and 55
to 70 MPa after 28 days. These strength characteristics
demonstrate equal performance to Portland cement. Anecdotally, there is evidence that C$A cements have the ability
to protect steel reinforcement against corrosion.
In comparison to Portland cement, C$A cement can
achieve energy savings as high as 25% and provide environmental benets by reducing CO2 emissions by around 20%.
The use of C$A cement as a construction material in countries other than China is entirely feasible, even initially as a
niche market product. With greater use the benets of this
cement will eventually become evident to the market and
its appeal as a high quality alternative to OPC/CEM1 will
grow. Lafarge has patented a class of cement clinkers based
on Belite, C$A and Calcium Aluminoferrite phases
(BCSAF) Gartner, 2012. These Belite-Calcium Sulfoaluminate Ferrite (BCSAF) clinkers can be used to make cement
in the usual way by being mixed with gypsum and other
materials, and are considered to be an intermediate
between Portland cements and C$A cements. BCSAFs
have the potential to be manufactured in much larger volumes than slag based cements as they do not require a
source of slag but show high content similar to that of
Portland cements. Due to the reactivity of the C$A phase,
BCSAF cements can have greater strength in the early
stages of development compared to Portland-slag cements
see Fig. 7. The above data was obtained from a pilot test
set up by Lafarge Central Research (LCR) and tested by
BRE which showed that cements based on C$A are promising alternatives to Portland cement; especially as such
206
Figure 7. Compressive strength of BCSAF compared to Portland cement, BRE concrete data at w/c = 0.55, 300 kg/m3 for pilot batch of BCSAF (B3)
compared to OPC (CEM1 425) (at 20 C).
clinkers can be formed in existing ordinary Portland

cement plants. However, the cost of raw materials is
greater than that of Portland cement, although according
to Gartner this may not be an economic factor once the
projected CO2 emissions costs (taxes) have been factored
in. The development and testing of C$A cements thus show
promise and could in time lead to the establishment of new
codes and standards.
3.3.2. Calcium aluminate (CaAl2O4) and calcium alumina
silicate cements
These cements are made in a rotary kiln by using bauxite
(an aluminum ore) instead of the typical calcium silicates
found in clays. The limestone and bauxite mix is fused into
a cement clinker in the same way as Portland cement. The
result is a special type of cement used for its ability to reach
high strength at a very early stage as well as its very good
heat and chemical resistance properties.
Although using this cement reduces the amount of CO2
produced during calcination, it is more expensive and less
readily available than Portland cement. In use, calcium aluminosilicate cements are often blended with high concentrations of GGBS, except in refractory applications where
they are used without slag.
3.3.3. Super-sulfated cements
Super sulfate cement is made by grinding a mixture of
8085% selected GBFS with 1015% calcium sulfate and
about 5% of Portland cement clinker. It is generally used
where high sulfate, acid and organic oil attacks on a structure are expected. Again the cost of this type of cement is
high, due to the limited availability of materials.
{Non-limestone based novel cements}
3.3.4. Magnesium-oxide based cement as a carbon negative

cement
Water-activated-magnesium-oxide based cement was
commonly used well before OPC ever came into existence.
It requires around 30% less energy to produce, and has some
signicant advantages over OPC. For example, when hardened, the cement is permeable, making it useful in terms of
heat regulation and control in the design of dwellings, particularly for warm climates. It can breathe, unlike OPC,
and so it has been referred to as living cement. Magnesium
based cements also have greater strength. Although it is an
ancient cement similar to what was at one time thought to
have been used by the Chinese to build the Great Wall,
major cement producers are today using this cement in modern applications, for example US Gypsums Grancrete, a
spray-on structural cement and in wallboard imported from
China. This type of cement is already used for housing in
developing countries. Argonne National Laboratories have
tested similar MgO-based Ceramicrete cements with a view
of developing them into more commercial products.
TecEco, a small Australian research and development
company, is one of the earliest players in this eld. They
have developed and been granted international patents
for TecEco cements in which reactive magnesia, also
known as caustic calcined magnesia, caustic magnesia or
CCM, is substituted for Portland cement. The reactive
magnesia hydrates to brucite, Mg(OH)2, and in
Eco-Cement exposed to the atmosphere, carbonates to
magnesite, MgCO3. Various cement formulations have
been developed by TecEco based on this fundamental concept including Tec-Cements, Eco-Cements and EnviroCements (TecEco Pty Ltd, 2013).
New research is underway to develop a magnesiumbased cement that absorbs more CO2 than it produces
during the manufacturing process (Biello, 2008). A working formulation of carbon-negative cement derived from
magnesium silicates was devised by Nikolaos Vlasopoulos,
chief scientist at London-based Novacem Ltd., an Imperial
College start-up, working in collaboration with Lafarge
and Laing ORourke. The aim was to license the process
by 2015. According to the inventors, magnesium silicates
are globally available but not uniformly distributed.
The precursor material, olivine (Mg, Fe)2SiO4, is carbonated in an autoclave process at a temperature of
180 C and pressure of 150 bars (Mineral Products Association, 2012; Vlasopoulos, 2010). The process produces
magnesium carbonate which is further heated in air at
700 C to produce magnesium oxide. The nal Novacem
cement composition is a blend of magnesium oxide and
hydrated magnesium carbonates, which inuence the
mechanical properties of the cement. It can be further
improved by reducing the water/cement ratio (Velandia
et al., 2011). As Novacem requires a much lower temperature to produce the cement precursor, it can use biomass
fuels to further reduce its CO2 emissions. The cement is
referred to as a carbon negative product not just because
of the fuel it uses but also because the CO2 it produces in
the manufacturing process is recycled back into the
process.
The production of 1 tonne of Novacem hydrated magnesium carbonate cement supposedly absorbs up to
100 kg more CO2 than it emits. In 2011 concrete trials were
undertaken with Laing ORourke and it was reported that
the concrete had achieved strengths of 4060 MPa, similar
to those of Portland cement.
However, on the 16th of October 2012 it was announced
that the Novacem Liquidator had sold the companys
Technology and Intellectual Property to Calix Limited
(Novacem announces company now closed and in liquidation, 2012). Despite the fact that MITs Technology
Review had ranked Novacems magnesium-based cement
to be among the 2010 top ten emerging technologies, the
company was unable to raise the necessary capital to continue the development of the technology. A further disadvantage of the product is that magnesium oxide is not as
abundant on land as calcium sourced from limestone.
3.3.5. Alkali-activated cements/geopolymers
Alkali-activated cements (AACs) are competitive with
ordinary Portland cement (OPC) in performance and cost,
and their production emits 95% less CO2 than OPC (if the
NaOH and KOH required are assumed to be carbon free);
they have longer life, better durability, and they recycle
millions of tons of industrial waste i.e., Recovered Mineral Components (RMCs).
AACs are not a limestone or calcium silicate based
cements, instead the chemistry is based on an aluminum
silicon system. The composition is simply made up of sand,
water, natural or synthetic pozzolans and another ingredient which is the alkali activator. The activator is usually
207
mixed into the water to make a solution before further

mixing. The alkaline solution decomposes the precursors
into silicate and aluminum units which then re-combine
to produce geopolymers. These aluminum and silicate
polymers grow to high molecular weights, creating a strong
binder. Although the rst geopolymers were based on
metakaolin, AACs are now generally separated into two
groups, alkali-activated y ash cement and alkali-activated
slag cement. But a mixture of the two, with or without
OPC is also in use (Bondar, 2007).
3.3.6. Sequestrated carbon cement
The Calera Corporation have a process that essentially
mimics marine cement, similar to what is found in the coral
reef, taking the calcium and magnesium in seawater and
captured carbon dioxide from euent gases to form carbonates. The idea is that CO2 rich gases are ltered through
sea water. The calcium and magnesium are stripped from
the sea water and react with CO2 to produce high quality
cement, which is snow white, air permeable and stronger
than regular OPC. Many other laboratories and scientic
institutes are looking into the same idea, however Calera
seem to be at the most advanced stages of development.
The Calera process is described in Fig. 8 (Calera, 2013).
Calera are at the moment testing concrete made from a
blended cement of OPC and Calera cement. There is an
expressed interest from the California Department of
Transport and Moss Land Power plant to utilize this
cement making process.
4. Current and projected economics of cement production
The cement industry has to cope with many economic
factors including energy prices, green taxes, production
costs and market forces that ultimately aect how much
a tonne of cement will cost. UK cement manufactures
rarely publish absolute values but give percentage changes;
together with cement price indices published by the government, this allows an evaluation of trends in the industry to
be made. This section looks at the UK, US and 2 MiddleEastern cement markets, to illustrate some of the economic
trends in cement production.
4.1. UK production and price indices
The latest UK cement industry statistics (20052011) are
plotted in Fig. 9 for the indexed cost of electricity and coal
used in production against the indexed cost of cement
(Department for Business Innovation and Skills, 2012;
Department of Energy and Climate Change, 2012). From
these plots it can be seen that electricity and coal have risen
by approximately 63% and 75%, respectively since 2006,
but the corresponding rise in the price of cement is around
35%. CEMEX has conrmed that the price rise was due to
higher kiln fuel and electricity costs that had to be recovered through price increases (Global Cement, 2012). The
208
Figure 8. Carbonation formation according to Calera.
UK Price Index of Cement and Fuel Components

200
Price Index (2005 = 100)
175
175
163
150
135
125
100
Electricity
Coal
75
2005
Cement
2006
2007
2008
Year
2009
2010
2011
Figure 9. UK cement and fuel component price trends.
data shows that electricity prices started to increase from

2005, with coal prices following a similar trend from
2007. The price of cement followed accordingly, rising steadily between 2005 and 2008; by the end of 2007 cement producers were expected to introduce budget-busting price
hikes, with an expected price increase of around 20%
(equivalent at the time to GBP 15 per tonne of cement
on top of the already set price of GBP 70 per tonne at
the start of 2008. However, the drop in demand for cement,
attributed to the credit crunch, was eective (thus far) in

mitigating further price increases.
Although coal prices are on the increase and electricity
prices show a steady trend, the price of cement is starting
to see a decrease with a price index, reaching 135 higher
than that of previous years but still below the peak in 2009,
due to reduced demand. Since 2011 cement production
increased in the UK by about 8% compared to 2010, perhaps signaling the start of a recovery in the cement market.
209
US Price Index For Cement and Fuel Components

200
Price Index (1998=100)
175
150
147
125
119
100
98
75
1998
2000
2002
2004
2006
2008
Electricity
Coal
Cement
2010
Year
Figure 10. US cement and fuel component price trends.
4.2. US production and price indices

Beyond the UK, cement industry statistics from the US
have also been evaluated and the results are plotted in
Fig. 10 (U.S. geological Survey, 2012; USGS, 2010; U.S.
Energy Information Administration, 2011). The plots show
cement price indices from 1998 to 2009, together with coal
and electricity price indices. A base index of 1998 = 100
was used. US cement prices have decreased by approximately 13% between 1998 and 2003. Coal prices also fell
during the same period (despite a small rise in 2002) but
electricity prices have either remained unchanged or
increased slightly. Cement prices started to rise from 2003,
reaching a peak of index price of 107 in 2006. This could
be due to the sharp increase in the price of coal at this time
(about 26%) as well as a continuing increase in electricity

prices.
From 2006 the cement industry faced a decrease in
cement prices, dropping by about 9% even when coal and
electricity prices were on the rise; this is similar to the eect
of the credit crunch on the UK price of cement, but it happened 23 years before that. The startling fact is that in
2009 the price of cement was eectively lower, albeit only
slightly, than what it was in 1998. The availability of low
cost Mexican cement has also not helped indigenous producers. So, not only has the US cement industry had to suffer a weak market and low demand, it has had to put a
squeeze on cement prices to compensate for increasing kiln
fuel and electricity prices over a good number of years.
Cement production has recently increased in the US and
Qatar Price Index of Cement and Fuel Components

200
175
175
150
125
111
102
100
75
2006
Electricity
Crude Oil
Cement
2007
2008
2009
2010
2011
2012
Year
Figure 11. Qatar cement and fuel component price trends.
210
Saudi Arabian Price Index of Cement and Fuel Components

200
175
175
150
132
125
101
100
75
2006
Electricity
Crude Oil
Cement
2007
2008
2009
Year
2010
2011
2012
Figure 12. Saudi Arabian cement and fuel component price trends.
there is an expectation that cement market prices will also

recover.
4.3. Qatar production and price indices

In Qatar, the rst of two Gulf Cooperation Council
(GCC) countries examined in this paper, the trends governing cement price are somewhat dierent. Qatar is notable
for having 4.24 tonnes of cement consumption per capita,
the highest in the world (Al Jazira Capital, 2011). Oil and
natural gas are the dominant fuels used in cement production. Qatars cement industry statistics (20062011) are
plotted in Fig. 11 for the indexed cost of electricity and
crude oil used in production against the indexed cost of
cement (Qatar Statistics Authority, 2013; NBK Capital,
2010). Qatar, as a major producer of natural gas, has stable
fuel costs for electricity generation. The Qatari government
has also set a maximum price for the sale price of cement.
All of these factors ensure stability at times of instability,
such as the crude oil price peak of 2008 attributed to Peak
Oil (Financial Times Lexicon, 2012); this enabled the
cement industry to weather the slowdown in construction
triggered by the global nancial crisis.
Yadullah Ijtehadi identied eight emerging trends that
are expected to dominate cement production in the GCC
(Ijtehadi, 2011). Trend (8) suggests that the future focus
of Qatar, as hosts of the 2022 FIFA World Cup, is sports
development. Plans in the pipeline for the intervening decade include the construction of sports stadia, new hotel
accommodation, airports, ports and numerous leisure
and recreational developments; cost US$ 230 billion. As
a consequence, Qatar will face a cement shortfall from
2013 that could, according to some sources, exceed 3 million tonnes per annum by 2015. This will drive up the cost
of cement due to a combination of construction material
and labor shortages The other trends are (1) Gulf cement
prots rising, (2) UAE construction sector rebound, (3)
UAE companies facing diculties as a consequence, (4)
Saudi clinker capacity rising, (5) Saudi fuel shortages, (6)
Saudi export bans and price manipulation, and (7) Kuwait
cement prices declining.
4.4. Saudi Arabian production and price indices
The biggest cement producer in the GCC is the Kingdom of Saudi Arabia (KSA). Their cement industry pricing
statistics (20062011) are plotted in Fig. 12 for electricity,
crude oil and cement (Al Jazira Capital, 2011). KSA has
suered dropping cement prices since 2008, but the trend
was reversed with an increase in cement prices by 5.4% in
the 3rd quarter of 2011. This is mainly attributed to
increased demand as reected by higher volumes of cement
sold.
KSA construction activity witnessed an increase as government tendered and implemented more government contracts; In March 2011, the King decreed the construction of
half a million new housing units, building of new hospitals
and the injection of capital into specialist credit institutions
to facilitate debt write-os and increase mortgage lending.
This has boosted the demand for cement and the trend is
expected to continue.
4.5. Comparison of price trends
The UK, US, Qatari and Saudi Arabian cement price
data in Sections 4.14.4 has been presented for dierent
base index years. Simultaneous comparisons of price are,
in any case, not possible without knowledge of the monetary price of a tonne of cement in each country, local
energy prices, wage structures, taxes, currency exchange
211
UK, US, Qatari and Saudi Cement Price Indeces

200
Price Index
175
150
135
125
102
101
100
98
UK Price
US Price
Qatari Price
75
1998
Saudi Price
2000
2002
2004
2006
2008
2010
2012
Years
Figure 13. UK, US, Qatari and Saudi Arabian cement price index trends.
rates, supply and demand trends, etc. Indexed prices can,

however, be compared directly to gain insight on overall
market trends. Fig. 13 shows the change in cement price
indices for the UK (2005 base) against the US (1998 base),
Saudi Arabia (2006 base) and Qatar (2006 base). From
2005/6 onwards we see a parting of the way between the
UK, where prices have continued to rise sharply, and the
others where the general trend has been one of steady or
declining prices.
At the end of 2005 one of the deadliest and most
destructive hurricanes, Katrina, hit the Gulf States in the
US. This was expected to result in a greater demand for
cement but in reality it constrained demand and delayed
cement deliveries (U.S. geological Survey, 2012). From
2006 to 2008 there were delays in new projects due to problems attributed to 2005 and to the drop in new home construction, both of which contributed to the decline in
cement production. By 2007 the US was already seeing
the start of tighter credit supply and decline in the housing
market and mortgage rates. By 2008 in the private sector
the pressure of a depressed market and the economic crisis
(the credit crunch) were in full swing; the lack of State
funding to reduce property tax revenues made matters
worse. During this time the US cement industry saw the
closure of three old production plants and the construction
of two new ones. The price of cement in the US fell to compensate for delays in projects and the recession; by lowering the price of cement a smaller but sucient prot was
made, eectively compensating for the decrease in production and cement sales. In 2009 a further 14 cement production plants were closed in the US and cement production
reached its lowest level in 12 years.
In contrast, the massive construction booms in KSA,
and Qatar over the same period, have helped the cement
sector to consolidate, expand and increase its protability
while at the same time keeping cement prices in check.

In Qatar, cement prices have remained steady due to the
government cap, with prices averaging US $68.7 per tonne.
KSA, on the other hand, achieved the same objective while
continuing to have the edge over other GCC countries due
to the favorable cost structures that benet its cement producers; specically, access to fuel at articially low prices
from the government, the ready availability of raw materials (limestone, primarily) and strong domestic demand.
Energy and raw material account for around 32% and
29%, respectively of the total production cost of cement
in KSA. At the end of 2011, the cost of cement in KSA
was US $64.6 per tonne, with Saudi cement manufacturers
maintaining and enjoying gross prot margins above 50%
compared to the GCC average of 30%.
The dierence is in part due to the dampening eect of
the economic crisis. In the UAE in 2010 roughly 50% of
building projects were put on hold. The result was stagnation of the cement market in the UAE and ooding of
other GCC markets with cheap (at cost) cement as excess
supply from UAE producers eectively depressed cement
prices in small, neighboring countries. The decline in sales,
demand and prots continues today to put pressure on
cement producers in the UAE, where the gross prot margin averages only 15.5%. Lafarge and Holcim, two of the
worlds largest cement producers, operate at a gross prot
margin of 26.7% and 42.8%, respectively. (Al Jazira Capital, 2011).
The story in the UK, which over the same period has
seen a 35% increase in cement prices, is dierent. UK prices
are also signicantly higher than in the US and GCC
region. The cost of cement in the UK in 2008 was approximately GBP 70 per tonne. In the US Qatar and KSA the
corresponding costs were approximately US $85 (GB 46),
Qatari Riyals, QAR 262 (GB 36) and Saudi Riyals, SAR
212
234 (GB 34) per tonne, respectively at the prevailing

exchange rates. Cement was thus 34%, 48% and 51%
cheaper in these countries (Taken, 2013).
The escalation in price of UK cement from 2005
onwards (Trout, 2011) is now summarized:
2005: Prices in 2005 were pushed up by a combination of
fuel costs and regulatory factors; cement prices in January
2006 rose by GB 56 per tonne. CEMEX explicitly stated
that higher kiln fuel and electricity costs were being recovered through higher pricing.
2006: Prices of building materials generally rose by 2.9%
in the rst half of 2006, but bricks were up by 6% and
cement was up by 8%. The upward trend continued when,
in September 2006, Lafarge announced a 15% rise in the
price of bulk cement from January 2007.
2007: In 2007, escalating prices led to the British Aggregates Association (BAA) commissioning Cartel Damage
Claims to investigate cement makers for giving preferential
treatment to their associated concrete businesses. The UK
Oce of Fair Trading investigated reports of discriminatory pricing in March 2007 that were rejected by the cement
manufacturers. It had become increasingly clear that higher
costs were in general being recouped from customers. The
price increase of cement products during 2007 was 67%.
2008: At the start of 2008 the rising cement price trend
was all too obvious. A calculation by EC Harris suggested
cement-based building materials had experienced ination
of 7.9% during the 12 months to February 2008. A 10% rise
since January was reported in August 2008. In October
2008 the annual gure had risen to 14.5% according to
the Department for Business, Enterprise and Regulatory
Reform (now the BIS), but that masked a slow-down to
4.7% in the latter six months as the recession started to bite.
In May 2008 an appeal by cement producers against a
cartel lawsuit was rejected in Germany. In November
2008, a European Commission investigation into a suspected price cartel allegedly maintained by the multinationals: Lafarge, Holcim, Heidelberg Cement, CEMEX and
Dyckerho was given a great deal of publicity. No case
was brought against cement producers in the UK, however.
2009: Prices continued to rise into 2009 but unevenly;
attempts to inate prices to compensate for falling volumes
could not last. Lafarge reported price rises of 8.6% raising
the index gure from 130.6 in December 2008 to 143.3 in
February 2009. Monthly levels declined steadily thereafter
as a reection of market weakness.
2010: During 2010 the annual cement price average
showed a decline for the rst time in years. The decline
was modest and in fact the price of cement remained
remarkably steady throughout the year compared to the
index of 134.6 in November and December 2009. Lafarge
reported pressure on pricing in 2010 and looking ahead,
at the turn of 2011, Hanson foresaw downward pressure
on prices in Europe. Holcims chief executive also warned
that cement prices would be kept under pressure by the
market.
2011: UK cement prices proved to be relatively at in

the UK in 2011 according to the government index. In
May 2011 the price was informally said to be around
GB 90 per tonne, rising to GB 96 per tonne of Ordinary Portland compared to GB 102 per tonne in May
2010 (David Langdon, 2012). The cost of UK cement is
23 times higher than US, Qatari and Saudi Arabian
cement.
2012: Indicatively, in March 2012 the Competition
Commission in Johannesburg reached a settlement with
Lafarge Industries South Africa in which the latter admitted to taking part in a price-xing and market division
cartel involving the main cement producers in South
Africa. Lafarge agreed to pay a penalty of Rand
148,724,400 (GB 10.41 Million), or around 6% of its
2010 annual turnover (n24, 2012). Similar practices and
outcomes have been reported in connection with other
cement manufacturers operating in India, Ghana, Trinidad and elsewhere.
4.6. Projections of future economic factors governing cement
production
The UK is the rst country with legally binding targets
for greenhouse gas emissions beyond 2020 (Trout, 2012).
A carbon price oor of GB 16 per tonne of CO2 was introduced from April 2013 and this is expected to rise to GB
30 per tonne in 2020. The introduction of the carbon price
oor was immediately opposed by industry as the costs
were so high and compensation was requested. In November 2011 it was announced that a package for energy intensive industries, such as cement, to the value of UK
250 Million would be available to help with high energy
costs and the carbon price oor plan. The package would
also help to raise the green taxes that were announced in
2012. It is estimated that the UK will pay an extra
36 Euros per megawatt hour (MWh) of electricity by
2020 with the introduction of climate change policies. This
compares with 22 Euros in Germany, 20 Euros in Denmark, 19.3 Euros in France and the equivalent of
12.7 Euros in China. (Global Cement, 2012). The dierences raise one of the core problems of any green or carbon
tax in a global economy i.e., if your neighbors do not
have the same tax as you they can undercut you. Similar
arguments exist in Australia and the US.
According to the Mineral Products Association (MPA),
the cement industry does not meet the requirements for the
rst 140 Million Euros of this package because support
for the sector is not permitted under the EU emissions trading scheme. What is also of concern is that the UK, had
production levels not been low due to the recession, would
have missed its own emissions targets. Since 1990 emissions
in the UK have dropped by 25%, but the UK will undoubtedly miss the targets that have been set for the next twenty
years. It is clear that some dramatic changes are needed to
make the cement industry, both in the UK and globally,
213
Figure 14. Global gross CO2 emissions per tonne of clinker per kiln type.
Annual savings attributed to CO2 reduction (at GB 16/tCO2 saved)

20,000,000
H
40% less CO2
Value (GB /yr)
16,000,000
12,000,000
H
20% less CO2
8,000,000
H
4,000,000
10% less CO2
0
0
2000
4000
6000
8000
10000
Clinker production (t/day)

Figure 15. The value of carbon emission reduction in gross cement production.
less energy intensive and more sustainable. The proposal is

that, through investment in alternative fuels and novel
cement technologies such as those that have been outlined
in Sections 3.13.3 of the present paper, the cement industry can achieve lower CO2 emissions, reduced costs and
increased protability, and at the same time pay less in
green taxes. Progress to date in stemming carbon emissions
from cement production are summarized in Fig. 14 (World
Business Council for Sustainable Development, 2009).
Given that the majority of kilns are of the dry type (with
or without preheater and/or precalciner), the range of CO2
emissions (E, in tonnes of CO2 per tonne of clinker) lies
somewhere between 0.842 (L) and 0995 (H) tonnes of
CO2 per tonne of clinker produced. Using the UK carbon
price oor (CPF, GB 16 per tonne of CO2 from 1st April

2013, rising to 30 in 2020), percentage carbon emission
reduction (R, %), plant size (T, tonnes of clinker per day)
and the number of days (D, days) of plant operation per
year, it is possible, to determine the annual monetary saving (S, GB per year) that can be achieved. The required
linear expression, which can be used to inform early investment decisions, is of the form:
S CPF D E R T
The range of savings (S) from 10%, 20% and 40% CO2
emission reductions (R) as a function of plant size (T),
assuming D = 300 days per year, is conveniently presented
in Fig. 15. These recurrent, annual savings can be
214
amortized by the plant owner over a period of years to determine either the total savings that would go toward funding
the improvements needed to deliver the savings, or alternatively the length of time needed to pay back the investment.
Thus, a 6,000 tonnes of clinker per day cement plant
owner aiming to reduce emissions by 40% would save
approximately GB 10 million per annum to invest. This
sum could be amortized over 5 years to cover the cost of
GB 50 million of investment in plant upgrade, or pay
back GB 100 million pounds in 10 years. Beyond these
periods, all long-term savings can be used to boost the bottom line and improve protability without increasing product cost. The capital cost of the aforementioned plant, built
to modern standards and assuming a unit cost of US $230
per tonne of clinker production per annum (Ingenieros,
2013), would be around US 180 million. In this context,
savings of US $50 or $100 million are substantial. It should
be noted that in this analysis, bank interest and service
charges (which are historically very low) and potential
tax incentives (which vary from country to country) have
not been considered, but that is easily remedied before a
commitment to invest is made.
5. Conclusions
It is clear that cement, in all its dierent types and forms,
is a vital product that, combined with other ingredients in
the correct ratio, makes it a key construction material.
Concrete is a prime example of a cement-based construction material. The demand for concrete is high, increasing
and recognizes no borders. This will continue to be the case
for the foreseeable future.
In order to ensure sustainable, cost-eective but still
protable cement production in the second decade of the
21st century, the industry needs to change. The two most
important challenges facing the industry are a pressing
need to reduce CO2 emissions and improve energy eciency. Some of the remedies have been outlined in this
paper, but more research is needed. The most eective
methods of producing green, environmentally and economically sustainable cements of the highest quality are (a) the
use of alternative, low carbon fuels and (b) development of
novel cement formulations and production methods.
Alternative fuels derived from waste are currently being
used in some parts of the world, helping to reduce energy
costs, generate income and reduce landll, but not all alternative fuels reduce CO2 emissions. The use of other fossil
fuels such as biomass, on the other hand, can be an eective
fuel substitute, producing CO2 emissions that are about
2025% less than those of coal. However, the IEAs predictions suggest that it will only be economically viable for the
cement industry to use biomass sourced alternative fuels
until 2030; it remains to be seen if other alternative low carbon fuels can be found or developed before then.
A large fraction of the CO2 that is released in the production of Portland cement is from the calcination process
itself; it is a byproduct of the ring of calcium carbonate
and silica in a rotary kiln to produce calcium silicate (clinker) and carbon dioxide. It is therefore conceivable that a
more permanent solution to achieving carbon reduction
is to use dierent raw materials and/or dierent manufacturing processes. These are subjects of major research initiatives worldwide, most of which generally remain
shrouded in secrecy, but there should be no doubt that
the race to develop the next generation of cements is
underway.
C$A cements use limestone as one of the raw materials
in their production but oer a 20% reduction in CO2 emissions by requiring a lower kiln ring temperature and
therefore burning less fossil and fossil-derived fuels. The
production of C$A cements in operational plants is possible as the manufacturing process is the same its use in
China dating back to the 1970s is testament to this. There
are fewer costs associated with plant conversion. However,
some of the raw materials used in the production of C$A
cements have been identied as being more expensive,
but this downside is potentially outweighed by savings on
carbon taxes. This makes C$A the most viable alternative
to Portland cement at this time; although the development
of robust internationally recognized regulatory standards
for these cements are required.
Novacems carbon-reducing cement, still in the early
stages of development, perhaps held the greatest promise
for entirely eliminating CO2 emissions from cement production. However, given the uncertainties of availability of the
right type of magnesium silicates, the large capital investment required to obtain magnesium oxide, unanswered
questions relating to long term strength and durability
and the fact that Novacem Ltd recently went out of business, the barriers to further development of the Novacem
process continue to be signicant if not insurmountable.
With new ownership development may resume and further progress may be made. However, the problems of integration with operational cement plants and substantial
start-up costs are likely to be signicant, so this novel
cement could eventually be overlooked. Other carbon negative cements and processes, such as the one developed by
Calera Corporation, are also early stage.
As discussed in Section 4 of this paper, there are many
economic factors that can adversely impact growth of the
cement industry. In recent years, decreases in cement production combined with sharp rises in energy costs have
caused the price of cement to fall in some cases and rise
in others, the common thread a desire by cement producers
to stay in business. Focusing on the latter, since 2009 the
UK has experienced a recession that saw a reduction in
construction projects which in turn contributed to a decline
in cement production, with the cost of this presumably
passed onto consumers. In 2012 it was evident that the
UK economy had not fully recovered and that a double-dip recession was the likely outcome. As a consequence of this, cement production has not reverted to its
previous highs although it is expected to gradually restructure and grow in 2013.
An important pre-requisite for investment in new, low

carbon cement technologies, is price stability. This is the
silver lining that manufacturers in Qatar and Saudi Arabia
can benet from as a consequence of government subsidies
and in the US as a consequence of a combination of a Hurricane Katrina and the economic crisis.
One very important development that will aect the
cement industrys future in the UK is the introduction of
a carbon tax on emissions and introduction of a carbon
price oor in April 2013. It is likely that other countries
in Europe and worldwide will introduce similar measures
aimed at carbon emission reduction. This is a double-edged
sword, bad in both cases if cement producers do nothing to
change, but potentially a great opportunity and winwin
situation if all of the changes required to deliver deep cuts
in carbon emissions are made, improving the long term sustainability and protability of cement production in this
and other countries.
In the do nothing scenario the cost of production will
increase signicantly as cement production continues to
emit large volumes of greenhouse gases into Earths atmosphere. There is still a huge demand for cement and the
industry contributes greatly to the economy and employment prospects of its host nations. But without change,
the cement industry will decline.
On April 16th of this year, the Saudi government, in
response to a severe shortage of locally produced cement,
ended the ban on cement imports and announced its intention of allowing 10 million tonnes of clinker to be imported
in the next 12 months (Global Cement Weekly, 2013). The
source of this cement is not known although it may be signicant that on the same day, Iran announced that it had
exported 13 m tonnes of cement over the past 12 months.
Clearly, Iran has surplus production. This is an excellent
example of local demand temporarily exceeding local supply, and the benets that exible cross-border trade in
cement can help to ll the gap.
References
Al Jazira Capital, 2011. Saudi Cement Sector, Research Department
Sector Report.
Association of Cementitious Material Producers (ACMP), South, Africa,
2010.
ASTM C150/C150M-12, Standard Specication for Portland Cement,
2012.
Battelle, 2002. Toward a sustainable cement industry: climate change
substudy.
Bentz, D.H., 2011. Optimization of cement and y ash particle sizes to
produce sustainable concretes. Cement Concrete Comp., 824831.
Biello, D., 2008. Cement from CO2: A Concrete Cure for Global
Warming? Scientic American.
Bondar, D., Lynsdale, C., Ramezanianapour, A., Milestone, N., 2007.
Alkali activation of natural pozzolan for geopolymer cement production. International Conference on Sustainable Construction, Materials
and Technologies, pp. 313317.
BSI, BS EN 197-1: 2011 Cement. Composition, specications and
conformity criteria for common cements, 2011.
Calera, The Science, 2013. <http://dev.calera.com/index.ppp/technology/
the_science/index.html>.
215
CEMBUREAU, 1991. Cement Standards of the World 1991, CEMBUREAU, Brussels.

CEMBUREAU, Key Facts and Figures about Cement, viewed online on
18 October 2012.
David Langdon, 2012. Spons Architects and Builders Price Book, RICS.
Department for Business Innovation and Skills, 2012. Monthly Statistics
of Building Materials and Components, <http://www.bis.gov.uk/
analysis/statistics/construction-statistics/building-materials>.
Department of Energy and Climate Change, 2012. UK Energy Price
Statistics,
<http://www.decc.gov.uk/en/content/cms/statistics/energy_stats/prices/prices.aspx>.
n24, 2012. Lafarge ned in cement cartel case, <http://www.n24.com/
Companies/Industrial/Lafarge-ned-in-cement-cartel-case-20120308>.
Financial Times Lexicon, 2012.
Gartner, E., 2012. Alternative binders for concretes with reduced CO2
emissions.
<http://webpages.mcgill.ca/sta/Group3/aboyd1/web/
Conferences/AMW%20IX/Gartner.pdf>.
Gartner, E.M., Macphee, D.E., 2011. A physico-chemical basis for novel
cementitious binders. Cement Concrete Res. 41, 736749.
Global Cement, Cement price trends in the UK, 2012. <http://www.globalcement.com/magazine/articles/643-cement-price-trends-in-the-uk>.
Global Cement Weekly, 2013. Issue: GCW96. <http://www.globalcement.com/news/itemlist/email/gcw96#160>1.
Hawkins, P., Tennis, P., Detwiler, R.J., 2003. The Use of Limestone in
Portland Cement: A State-of the-Art Review EB227. Portland Cement
Association, Skokie, Illinois, USA.
Hendriks, C.A., 2004. Emission Reduction of Greenhouse Gases
from the Cement Industry. Greenhouse gas control technologies
conference paper. California: IEA Greenhouse gas and R&D
programme.
Hendriks, C.A., Worrell, E., Price, L., Martin, N., Ozawa Meida, L.,
1999. The reduction of greenhouse gas emissions from the cement
industry. Cheltenham, UK, IEA Greenhouse Gas R&D Programme,
Report PH3/7.
Hendriks, C.A., Worrell, E., de Jager, D., Blok, K., Riemer, P., 2004.
Emission Reduction of Greenhouse Gases from the Cement Industry,
IEA greenhouse gas control technologies conference.
Ijtehadi, Y., 2011. Eight Emerging Trends in GCC Cement, http://
www.zawya.com/story/ZAWYA 20120612054032/.
Is it worth producing cement in the UK?, Global Cement, 2012. <http://
www.globalcement.com/news/item/1050-is-it-worth-producingcement-in-the-uk>.
Joint Research Centre, 2012. Institute for Prospective Technological
Studies, Sustainable Production and Consumption Unit, European
IPPC Bureau, Best Available Techniques (BAT) Reference Document
for the Production of Cement, Lime and Magnesium Oxide, Industrial
Emissions Directive 2010/75/EU (Integrated Pollution Prevention and
Control), Draft CLM BREF.
Lafarge Cement UK, 2011, Aberthaw Works brochure, <http://www.lafarge.co.uk/wps/portal/uk/2_8_2_a_2-Aberthaw_Works>.
Lawson, J., 2007. The Environment Footprint of Surface Freight
Transport. Transport Research Board, Ottawa.
Mahasenan, M., Smith, S., Humphreys, K., Kaya, Y., 2003. The cement
industry and global climate change: current and potential future
cement industry CO2 emissions. In: Greenhouse Gas Control Technologies 6th International Conference. Pergamon, Oxford, pp. 995
1000.
Matschei, T., Lothenbach, B., Glasser, F.P., 2007. The role of calcium
carbonate in cement hydration original research article. Cement
Concrete Res. 37 (4), 551558.
Mineral Products Association (MPA) Fact sheet 12, Novel cements: low
energy, low carbon cements, 2012. <http://cement.mineralproducts.org/downloads/fact_sheets.php>.
Mineral Products Association Fact sheet 7, Alternative fuels and raw
materials in cement kilns, 2012. <http://cement.mineralproducts.org/
downloads/fact_sheets.php>.
Muller, N., Harnisch, J., 2008. A Blueprint for a Climate Friendly Cement
Industry: How to Turn Around the Trend of Cement Related
216
Emissions in the Developing World. A report prepared for WWF

International, Gland, Switzerland.
NBK Capital, 2010. Qatar National Cement.
New Zealand Cement Holdings, 100 years Helping Build a Nation.
Milburn Centenary; Christchurch, N.Z., 1988.
Norchem, 2011. Silica fumes applications in sustainability, <http://
www.norchem.com/applications-sustainability.html>.
Novacem announces company now closed and in liquidation. http://
novacem.com/wp-content/uploads/2012/10/Novacem.16-October2012.pdf, (accessed 21.10.12).
Oda, J., Akimoto, K., Tomoda, T., Nagashima, M., Wada, K., Sano, F.,
2012. International comparisons of energy eciency in power, steel
and cement industries. Energy Policy 44, 118129.
OECD/IEA and the World Business Council for Sustainable Development, Cement Technology Roadmap, 2009.
Portland Cement Association, 2013. A green option for Canadian
concrete construction, <http://www.cement.org/tech/cct_PLC.asp>.
Qatar Statistics Authority, 2013. Annual Consumer Price Index (CPI) and
Annual Producer Price Index (PPI), Qatar Information Exchange,
<http://www.qalm.gov.qa/>.
Schneider, M., Romer, M., Tschudin, M., Bolio, H., 2011. Sustainable
cement production present and future. Cement Concrete Res. 41 (7),
642650.
Sharp, J.H., Lawrence, C.D., Yang, R., 1999. Calcium Sulfoaluminate
cements low energy cements, special cements or what? Adv. Cement
Res. (CSA J.) 11 (1), 313.
SIME Ingenieros, S.A., How much a mini cement plant costs?, 2013.
<http://www.simeingenieros.com/site/?page_id = 905&lang = en>.
Smith, R.A., Kersey, J.R., Griths, P.J., 2002. The construction industry
mass balance: resource use, wastes and emissions, Virdis, Report VR4.
Taken from <http://www.exchange-rates.org/>, 2013.
Taylor, M., Tam, C., Gielen, D., 2006. Energy Eciency and CO2
Emissions from the Global Cement Industry. Paper prepared for the
IEA-WBCSD workshop: Energy Eciency and CO2 Emission Reduction Potentials and Policies in the Cement Industry, IEA, Paris, 45.
TecEco Pty Ltd, TecEco Cements, 2013. <http://www.tececo.com.au/
technical.tececo_cements.php>.
Trout, E.A.R., 2011. Cement price trends in the UK, Global Cement,
<http://www.globalcement.com/magazine/articles/643-cement-pricetrends-in-the-uk>.
Trout, E.A.R., 2012. The British cement industry in 2011 and 2012,
Global Cement, <http://www.globalcement.com/magazine/articles/
706-the-british-cement-industry-in-2011-and-2012>.
U.S. Energy Information Administration, 2011. Annual Energy Review,
<http://www.eia.gov/totalenergy/data/annual/perspectives.cfm>.
U.S. geological Survey (USGS), 2012. Mineral commodity summaries,
<http://minerals.usgs.gov/minerals/pubs/commodity/cement/>.
USGS, 2010. US Cement statistics, <http://minerals.usgs.gov/ds/2005/
140/cement.pdf>.
USGS Mineral Commodities Summary, January 2012.
van Oss Hendrick, G., 2012. Minerals Yearbook 2010, Slag, Iron and
Steel, United States Geological Survey.
Velandia, D.M., Devaraj, A., Barranco, R., Vlasopoulos, N., Novacem
A novel cement for the construction industry, Cement and Concrete
Science Conference, 1213 September 2011. <http://novacem.com/wpcontent/uploads/2012/01/Cement-and-concrete-science-2011-conference-vF.pdf>.
Vlasopoulos, N., 2010. Novacem carbon negative cement, SCI technical
update, 25th November. <http://novacem.com/wp-content/uploads/
2010/12/20101125-Technical-update.pdf>.
World Business Council for Sustainable Development/The Cement
Sustainability Initiative. Cement Industry Energy and CO2 Performance: Getting the Numbers Right, 2009. <http://www.groundwork.org.za/Cement/csi-brochure.pdf>.
World Business Council for Sustainable Development, Sustainable,
Construction 2012.

Green Technology in Cement PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Green Technology in Cement PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Green Technology in Cement PDF

Uploaded by

Copyright:

Available Formats

International Journal of Sustainable Built Environment (2012) 1, 194216

Gulf Organisation for Research and Development

International Journal of Sustainable Built Environment

Trends and developments in green cement and concrete technology

Corresponding author. Tel.: +44 1224 272506.

E-mail addresses: [email protected], [email protected] (M.S. Imbabi).

Production and hosting by Elsevier

Classification of Portland cements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2002). Today, the OPC market is dominated by China,

part of the initiative is a database showing CO2 emissions

2. Portland-based cements and other hydraulic binders

This produces a powder that will react with water and

Portland cement and up to 5% of minor additional constituents (the original OPC)

rosive, alkaline substance. As the water becomes saturated

The main bond mechanism is not capillary force, as is

America (excl USA)

Asia (excl China,

*Excluding EU27 countries not members of CEMBUREAU

Figure 1. World Portland cement production today.

(Mt / year produced: Records and estimates)

Figure 2. World Portland cement production 19902050.

1 kg of cement produced gives a by-product of 0.9 kg of

Factory made mortars

Figure 3. Cement, concrete and plaster products in the UK construction market.

The production process is diagrammatically shown in

Dry kiln process

Wet kiln process

The ratio of Portland cement clinker to additives.

Figure 5. Energy eciency in clinker production (Oda et al., 2012).

clinker (wet process)). It should be noted these gures

2.5. Future CO2 emissions if we continue business-as-usual

In order to improve energy eciency and reduce carbon

countries, notably Germany (Joint Research Centre,

The remainder of the section will touch on alternative

combustion systems. Where bottom fuel ash is left in the

facture in a kiln. Reductions in CO2 are signicant due to

being manufactured in conventional Portland cement

clinkers can be formed in existing ordinary Portland

3.3.4. Magnesium-oxide based cement as a carbon negative

mixed into the water to make a solution before further

Figure 8. Carbonation formation according to Calera.

UK Price Index of Cement and Fuel Components

Price Index (2005 = 100)

Figure 9. UK cement and fuel component price trends.

data shows that electricity prices started to increase from

attributed to the credit crunch, was eective (thus far) in

US Price Index For Cement and Fuel Components

Price Index (1998=100)

Figure 10. US cement and fuel component price trends.

4.2. US production and price indices

(about 26%) as well as a continuing increase in electricity

Qatar Price Index of Cement and Fuel Components

Price Index (2006=100)

Figure 11. Qatar cement and fuel component price trends.

Saudi Arabian Price Index of Cement and Fuel Components

Price Index (2006=100)

there is an expectation that cement market prices will also