TXR Multirad Table SM 1103r3i

Technical Publication
SM-1103R3
Service Manual
General Purpose Rad Table
This product bears a CE marking in accordance with the provisions of the 93/42/EEC MDD dated June 14, 1993.
Este producto ostenta una marca CE de acuerdo con las disposiciones de la Directiva 93/42/CEE del 14 de Junio de 1993 sobre Productos Mdicos.
Ce produit porte la marque CE de conformit aux rglements de la Directive 93/42/CEE du 14 juin 1993 relative aux Produits mdicaux.
The information comprised in this manual applies to the following equipments

La informacin contenida en este manual se aplica a los siguientes equipos
Linformation contenue dans ce manuel est applique aux quipements suivants
MULT-FWFTT Four-Ways Floating Top Table MULTIRAD
Manufactured by:
Fabricado por:
Fabriqu par:
SEDECAL
Sociedad Espaola de Electromedicina y Calidad S.A.
Pelaya, 9 -- 13. Polgono Industrial Ro de Janeiro
28110 Algete, Madrid -- Espaa (Spain)
Phone: +34 916 280 544
Fax: +34 902 190 385
www.sedecal.com

Service Manual
REVISION HISTORY
REVISION
DATE
REASON FOR CHANGE
MAY 23, 2011
First edition
AUG 09, 2013
Design changes
SEPT 09, 2013
General Update
NOV 05, 2013
Ammended distance of anchoring holes
This Document is the english original version, edited and supplied by the manufacturer.
The Revision state of this Document is indicated in the code number shown at the bottom of this page.
SM-1103R3

Service Manual
ADVISORY SYMBOLS
The following advisory symbols will be used throughout this manual. Their
application and meaning are described below.
DANGERS ADVISE OF CONDITIONS OR SITUATIONS THAT

IF NOT HEEDED OR AVOIDED WILL CAUSE SERIOUS
PERSONAL INJURY OR DEATH.
ADVISE OF CONDITIONS OR SITUATIONS THAT IF NOT

HEEDED OR AVOIDED COULD CAUSE SERIOUS PERSONAL
INJURY, OR CATASTROPHIC DAMAGE OF EQUIPMENT OR
DATA.
Advise of conditions or situations that if not heeded or

avoided could cause personal injury or damage to equipment
or data.
Note
Alert readers to pertinent facts and conditions. Notes represent

information that is important to know but which do not necessarily
relate to possible injury or damage to equipment.
SM-1103R3

Service Manual
SAFETY SYMBOLS
The following safety symbols may appear in the equipment.
Their meaning are described below.
Caution. Consult accompanying documents.
Safety Symbol. Follow instructions for use, especially those

instructions identified with Advisory Symbols to avoid any
risk for the Patient or Operator.
(Only applies to IEC 60601--1 Standard -- Third edition)
General Mandatory action.
Type B applied part.
IPX0
Protection against harmful ingress of water or particulate matter.

IP Classification: Ordinary.
Ionizing radiation.
Non-ionizing electromagnetic radiation.
Radiation of Laser apparatus.

Do not stare into beam.
(Only applicable to equipment with Laser Pointer)
Dangerous voltage.
SM-1103R3

Service Manual
General warning, caution, risk of danger.
Warning: Ionizing radiation.
Warning: Non-ionizing radiation.
Warning: Laser beam.
Warning: Dangerous voltage.
Warning: Do not place fingers between mobile and fixed parts of the equipment, it
may cause serious injuries to patient or operator.
As well, make sure the patient extremities are correctly positioned into limit areas
during operation, movement of parts may cause serious damages to patient.
Electrostatic sensitive devices.
No pushing.
No sitting.
No stepping on surface.
SM-1103R3

Service Manual
Stop (of action).
Emergency stop.
ON power.
OFF power.
ON / OFF (push-push).
Each position, ON or OFF, is a stable position.
Alternating current.
Three-phase alternating current.
Three-phase alternating current with neutral conductor.
Connection point for the neutral conductor on Permanently Installed equipment.
Direct current.
SM-1103R3

Service Manual
Both direct and alternating current.
Protective Earth (Ground).
Earth (Ground).
This symbol according to the European Directive indicates that the Waste of
Electrical and Electronic Equipment (WEEE) must not be disposed of as unsorted
municipal waste and must be collected separately. Please contact an authorized
representative of the manufacturer or an authorized waste management company
for information concerning the decommissioning of your equipment.
Li/Pb/Cd/Hg
This separate collection symbol is affixed to a battery or its packing, to advise that
the battery must be recycled or disposed of in accordance with local or country
laws. The letters below the symbol indicate whether certain elements (Li=Lithium,
PB=Lead, CD=Cadmium, Hg=Mercury) are contained in the battery. All batteries
removed from the equipment must be properly recycled or disposed. Please contact
an authorized representative of the manufacturer or an authorized waste
management company for information concerning the decommissioning of your
equipment.
Pollution Control. (Only applicable to Peoples Republic of China (PRC)).
This symbol indicates the product contains hazardous materials in excess of the
limits established by the Chinese Standards. It must not be disposed of as unsorted
municipal waste and must be collected separately. Please contact an authorized
representative of the manufacturer or an authorized waste management company
for information concerning the decommissioning of your equipment.
SM-1103R3

Service Manual
TABLE OF CONTENTS
Section
1
Page
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1
Objective and Scope of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRE-INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
Pre-Installation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Responsibilities of the Purchaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Room Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2
Floor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.3
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Undertable Installation of the Generator (option) . . . . . . . . . . . . . . . . . . . . . . . .
12
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
5.1
Brake Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
5.2
Pedal Microswitch Replacing and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
PERIODIC MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
6.1
Maintenance Activities Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
6.2
Checking of Radiographic Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
6.3
Check Off Maintenance Revision Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
SYSTEM INTERCONNECTION MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
SM--1103R3

Service Manual
ii
SM--1103R3

Service Manual
SECTION 1
1.1
INTRODUCTION
OBJECTIVE AND SCOPE OF THIS MANUAL

This Service Manual is intended to describe the installation, adjustments,
troubleshooting and periodic maintenance of the Radiographic Table.
OPERATOR AND SERVICE MANUALS SHOULD BE

CAREFULLY READ AND UNDERSTOOD BY SERVICE
PERSONNEL BEFORE USING AND SERVICING THE
EQUIPMENT,
ESPECIALLY
THE
INSTRUCTIONS
CONCERNING SAFETY, REGULATORY, DOSAGE AND
RADIATION PROTECTION. KEEP THE MANUALS WITH THE
EQUIPMENT AT ALL TIMES AND PERIODICALLY REVIEW
THE OPERATING AND SAFETY INSTRUCTIONS.
SERVICE
PERSONNEL
MUST
HAVE
SUFFICIENT
KNOWLEDGE TO COMPETENTLY PERFORM THE SERVICE
TASKS RELATED TO X-RAY DEVICES AND PARTICULARLY
TO THE EQUIPMENT DESCRIBED IN THIS MANUAL. THIS
KNOWLEDGE IS ACQUIRED THROUGH A VARIETY OF
EDUCATIONAL
METHODS
FOR
TECHNICIANS
IN
ACCORDANCE WITH LOCAL LAWS OR REGULATIONS,
INCLUDING SPECIFIC TRAINING ON THIS EQUIPMENT.
1.2
TOOLS AND TEST EQUIPMENT

The following tools and test equipment are required for the installation:
SM-1103R3
Standard service engineers tool kit.
Standard and extended levels (1 meter for Column Base).
Electric drill motor and assorted bits.

Service Manual
This page intentionally left blank.
SM-1103R3

Service Manual
SECTION 2
2.1
PRE-INSTALLATION
PRE-INSTALLATION CHECK
Prior to beginning installation, it is recommended to inspect the site and verify
that the X-ray room complies with Pre-installation requirements, such as:
incoming line, main switch(es), safety devices, conduits and space
requirements.
Note
2.2
For more Pre-installation requirements,

Pre-Installation Manual of the Generator.
also
refer
to
RESPONSIBILITIES OF THE PURCHASER

The purchaser is responsible for the completion of Pre-Installation. This
includes the procurement and installation of all required materials and services
to get the room ready for the installation of the product.
2.3
ROOM REQUIREMENTS
2.3.1
ENVIRONMENTAL REQUIREMENTS
Note
STORAGE values only refer to equipment that is still in shipping

containers. If the equipment is partially or completely installed,
refer to IN USE values.
RELATIVE HUMIDITY
(Non-Condensing)
IN USE
MIN.
STORAGE
MAX.
75%
30%
Note
SM-1103R3
TEMPERATURE
MIN.
10%
IN USE
ATMOSPHERIC PRESSURE
STORAGE
IN USE
STORAGE
MAX.
MIN.
MAX.
MIN.
MAX.
MIN.
MAX.
MIN.
MAX.
100%
10o C
(50o F)
40o C
(104 oF)
--40o C
(--40o F)
70oC
(158o F)
700 hPa
1060 hPa
500 hPa
1060 hPa
These environmental conditions do not include the Digital

Detector. Refer to the Digital Detector Documentation.

Service Manual
2.3.2
FLOOR REQUIREMENTS
The method of installing the Table is anchor to floor with 4 x M10 bolts.
The Drill Templates of the anchoring holes are shown in the next illustrations.
Potential for Injury and/or Equipment Damage: Floor anchors

must be a minimum of 150 mm (6) from any concrete edge
including ducts and cracks. In addition, the general condition
of the concrete in the immediate mounting area should be
inspected to ensure that anchors will be set in good quality
concrete.
The floor bearing must be concrete and the thickness to be determined by a

Structural Engineer to properly support the equipment loads. The anchors
require a minimum embedment of 57.2 mm (2 1/4) into the concrete. If the floor
thickness is less than 101.6 mm (4), it is recommended that the unit be secured
using a through-bolt method with a reinforcement plate on the back side.
Note
The maximum tolerance for the Floor levelling should be

1.5 mm per meter (0.02 per feet).
Illustration 2-1
Drill Template
20
(0.8)
12
(0.5)
DETAIL A
SM-1103R3

Service Manual
2.3.3
TECHNICAL SPECIFICATIONS
POWER LINE REQUIREMENTS

Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .
24 VDC
Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 VA
DIMENSIONS AND WEIGHT
SM-1103R3
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
770 mm (30.3)
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2200 mm (86.6)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
825 mm (32.4)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
150 kg (330.7Ib)
Dimensions of Floating Table-Top . . . . . . . . .
2200 x 825 mm
(86.6 x 32.4)
Table-Top / Receptor distance . . . . . . . . . . . .
102 mm (4)
(4, 0.15)
Table-Top Attenuation . . . . . . . . . . . . . . . . . . .
<1.0 mm Al eq.
Longitudinal travel of Table-Top . . . . . . . . . . .
900mm (35)
Transverse travel of Table-Top . . . . . . . . . . .
230 mm (9)
Longitudinal travel of Receptor . . . . . . . . . . .
518 mm (20.3)
Grid (standard) . . . . . . . . . . . . . . . . . . . . . . . . .
40 lines/cm - 12:1
Cassettes / Detector sizes . . . . . . . . . . . . . . .
from 18 to 43 cm
(from 7 to 17)

Service Manual
Illustration 2-2
Dimensions
SM-1103R3

Service Manual
SECTION 3
UNPACKING
The system is shipped in different crates to facilitate transport and installation.
Upon receipt of components and parts of the equipment, inspect all shipping
crates for signs of damage. If damage is found, immediately notify the agent or
carrier.
1.
Place crates close to the location in the room where the system is
intended to be placed and remove each wood--packed part. Do not
discard any packing material (envelopes, boxes, bags) until all parts are
identified as listed in the packing list.
AT LEAST TWO PEOPLE ARE REQUIRED TO REMOVE ALL

HEAVY COMPONENTS FROM THE SHIPPING PALLET.
SM-1103R3
2.
When the equipment is unpacked, check the part and serial number of
each components identification label. Inspect all pieces for visible
damages. If any damaged part is found, repair it or order a replacement
to prevent unnecessary delay in installation.
3.
Verify that all items on the customer order are present.
4.
Leave a free working area around the equipment until installation is

complete.

Service Manual
SM-1103R3

Service Manual
SECTION 4
Note
INSTALLATION
Follow Installation sequence process as described. At least two or

three people are required for the following tasks.
1.
Remove the transport screws that secure the Radiographic Table to the
pallet and move away the Table.
2.
Remove the front cover screws of the Table in order to access inside the
Table.
3.
Power ON the Collimator Lamp and align perfectly the Receptor axes
with the Collimator light beam. During alignment, place the
Tube-Collimator Assembly and the Receptor Carriage at different
positions to check that it is correctly aligned.
4.
Mark on the floor the four anchoring holes of the Table Base.
ANCHORING HOLES
Note
SM-1103R3
5.
Move away the Table Base and prepare its anchors.
6.
Position the Table Base at its final place and anchor the Table Base to the
floor. Check that it is properly leveled placing levels in different points of
the Upper Frame. Use leveling plates to level the Base, before attaching/
fixing/ installing definitively the Table.
Use an extended level (1 meter) or several standard levels placed

in different points for leveling the Table Base.

Service Manual
7.
Note
This Table can be also power supplied by a 24 VDC External

Power Supply instead of a Generator.
8.
Note
If applicable, connect the Table Receptor Cable directly to the Terminal

Block 3TS1 in the Generator, and the Table Ion Chamber Cable to the
Generator as indicated in schematic IM-341.
Refer to the Generator Service Manual for further information.
9.
10
Connect the Power Supply cable for the Table Locks from the Table TS1
to TB7 of the Lock Board in the Generator, and connect the GND cable
from the Table Base to the GND Stud in the Generator (refer to
schematics IM-341 and 54303079).
Route the cables through the rear cables outlet of the Table Base along
the room for their later connection.
10.
Re-install the Front Cover of the Table Base.
11.
Remove the two rubber stops of the same end of the Table-Top.
SM-1103R3

Service Manual
12.
Install the Table-Top from one of the Table sides (right or left) inserting the
Bearings inside their Rails. At least two people are required for this
operation.
Be sure that the Table-Top slides over the bearings and the
Longitudinal Lock Pin does not block its way.
SM-1103R3
13.
Remove the wire tie-wrap of the Longitudinal Lock Pin.
14.
Re-install the rubber stops of the Table-Top end.
11

Service Manual
4.1
UNDERTABLE INSTALLATION OF THE GENERATOR (OPTION)

Follow the steps below to install the Generator underneath the Table.
1.
Remove the Front Cover after unscrewing the four (4) screws.
FRONT COVER SCREWS
2.
Disconnect the ground cable and dismount the front cover.
3.
Disconnect the three faston terminals of microswitch SW1 located inside

the Table Base.
4.
Remove the four (4) allen screws of the pedal assembly at both sides of
the Table Base (a pair on each side) and pull out the pedal assembly.
MICROSWITCH SW1
PEDAL ASSEMBLY SCREWS
12
SM-1103R3

Service Manual
5.
Place the Generator Cabinet (without covers) on its carriage in front of

the Table. This component is freestanding below the Table. Seismic
areas and other conditions require the Generator Cabinet to be secured
to the floor through the mounting holes on the bottom.
GENERATOR CARRIAGE
Note
SM-1103R3
Do not slide the Generator under the Table until Configuration and
Calibration procedures are completed. Refer to the Generator
Service Manual for further information.
6.
Once configured and calibrated, push the Generator inside the Table.
7.
Reassemble all of the components, parts and connections; then replace

the Front Cover of the Table.
13

Service Manual
14
SM-1103R3

Service Manual
SECTION 5
5.1
ADJUSTMENTS
BRAKE ADJUSTMENT
Note
As brakes come factory-adjusted, field adjustment should only be

necessary when replacing Brakes.
All brakes must have a space between the brake surface and the contact
surface of less than or equal to one (1) millimeter (1mm). If the space is too
close, the equipment may drag, or movements may be difficult. If the space is
too large, the brakes may not be strong enough to block movement.
To raise, lower or level the Brake Assembly, loosen the screws indicated in the
following illustration and move the Brake Assembly to the desired position.
Illustration 5-1
Lateral and Receptor Brakes
Screws
Lateral Brake
Screws
Receptor Brake
SM-1103R3
15

Service Manual
5.2
PEDAL MICROSWITCH REPLACING AND ADJUSTMENT

1.
Remove the Table Front Cover.
2.
Disconnect Microswitch cables (check previously the cable identification

to connect the cables to the new switch in the same position).
3.
Remover nut 2, for that hold nut 1 with a 14 mm. open wrench and loose
nut 2 with another 14 mm. Remove nut 2.
4.
Remove defective Microswitch.
5.
Install the new Microswitch.
6.
Adjust the Microswitch at 1 or 2 mm. from the cam to the wheel neck with
the Table Pedal fully pressed.
Illustration 5-2
Microswitch Replacement
Nut 1
Nut 2
Adjust at 1 or 2 mm
Microswitch Wheel
Wheel neck
CAM
16
SM-1103R3

Service Manual
7.
Check that the rolling wheel is perfectly aligned with the cam movement
to ensure proper activation of the wheel.
8.
Avoid wrong assembling of Microswitch as shown in illustrations below:
Illustration 5-3
Wrong Installation of Microswitch
Rolling wheel not aligned
Rolling wheel not aligned
Rolling wheel too close to cam, microswitch breaks
9.
SM-1103R3
Re-install the Table Front Cover.
17

Service Manual
18
SM-1103R3

Service Manual
SECTION 6
PERIODIC MAINTENANCE
The maintenance service has to be performed every twelve (12) months after
the installation.
6.1
MAINTENANCE ACTIVITIES DESCRIPTION

Electrical cables and connections: Visually check for electrical cables proper
isolation and proper connection inside and outside the unit.
Functional Check: Perform a functional check of the equipment, motion of
Table-top, locks, brakes and detents. Adjust or replace as needed.
Adjustments: Perform adjustments as explained in the Adjustments Section
of this manual.
Lubrication: Lubricate mobile components such as guides, bearings, etc.
Cleaning: Clean from dust or moist inner components as grids, bearings and
rails.
6.2
CHECKING OF RADIOGRAPHIC TABLE
SM-1103R3
1.
Turn OFF the system and mains. Check that there is not voltage at Table.
2.
Disassemble Front Table cover.
3.
Check anchoring screws of the Table, they should be strongly tighten.
4.
Turn On the system and press the mushroom shaped switch. Verify that
table is disconnected and the Table travels are blocked.
5.
Release the mushroom shaped switch.
6.
Connect Table power and check Table-Top brakes and correct motion by
pressing the Table Pedal.
7.
Assemble the Front Table cover.
8.
Release the horizontal Receptor brakes and check correct traveling.
9.
Take out the Cassette film tray and check correct functioning.
19

Service Manual
6.3
CHECK OFF MAINTENANCE REVISION TABLE
Hospital name:
Date:
System Name:
System Number ID:
Customer:
Field Engineer Name:
Radiographic Table
Maintenance activity
20
Comments
Electrical cables and connections
Brakes, locks and detents
Functional Check
Adjustment
Replacement
Lubrication
Cleaning
SM-1103R3

Service Manual
SECTION 7
RENEWAL PARTS
A -- RADIOGRAPHIC TABLE
B -- RECEPTOR ASSEMBLY
SM-1103R3
21

Service Manual
ITEM
DESCRIPTION
QTY
REFERENCE
REMARKS
RADIOGRAPHIC TABLE
A1
Tabletop Kit
SAT--A11008--01
A2
Tabletop Bumper
SAT--31617--01
A3
Eccentric Alignment Bearing Kit
SAT--A9874--01
A4
Concentric Alignment Bearing Kit
SAT--A9873--01
A5
Axial Bearing Kit
SAT--A9872--01
A6
Tabletop Lineal Bearing Kit
SAT--A9842--01
A7
Receptor Brake Kit
SAT--A9871--01
A8
Receptor Bumper
SAT--51865P04
Includes 2 units
A9
Receptor Carriage Bearing Left Kit
SAT--A9869--XX
XX= 01 Bucky standard

XX= 02 BDC and BDG
A10
Receptor Carriage Bearing Right Kit
SAT--A9870--XX
XX= 01 Bucky standard

XX= 02 BDC and BDG
A11
Tabletop Brake
SAT--S0025036
A12
Lock Pin
SAT--A11007--01
A13
Microswitch
SAT--50605015
A14
Spring
SAT--11330--01
A15
Overlay Pedal
SAT--55801403
22
Includes 4 units
SM-1103R3

Service Manual
A1
A4
A12
A2
A3
A5
A6
B
A8
A7
A9
A12
A10
A11
A13
A15
A14
SM-1103R3
23

Service Manual
A2
A3
A6
A5
A9
A7
A10
A12
24
A4
A8
A11
A14
A15
SM-1103R3

Service Manual
ITEM
QTY
REFERENCE
Vacutec Ion Chamber
6695--21
AID Ion Chamber
6695--11
Medys Ion Chamber
6695--66
Claymount Ion Chamber
6695--56
Bucky USX--Ray
SAT--6685--11
Sensing Tray
SAT--6694--05
Manual Tray
SAT--A8894--01
1B4
Push button
SAT--50613014
1B5
Handle
SAT--54402014
1B
1B1
1B2
1B3
DESCRIPTION
REMARKS
BUCKY ASSEMBLY
1B1
1B4
1B5
1B2
1B3
SM-1103R3
25

Service Manual
ITEM
2B
2B1
2B2
DESCRIPTION
QTY
REFERENCE
REMARKS
DETECTOR CABINET WITH NON ROTATING TRAY

Frame 1.5mm for Grid 1m
SAT--A10521--01
Frame 1.5mm for Grid 1.3m
SAT--A9657--02
SAT--A10523--01
SAT--A9656--02
SAT--A10522--01
Frame 2mm for Grid 1m
SAT--A10667--01
Frame 2mm for Grid 1.3m
SAT--A10666--01
SAT--A10665--01
SAT--A10664--01
SAT--A10663--01
SAT--A10667--02
SAT--A10666--02
SAT--A10665--02
SAT--A10664--02
SAT--A10663--02
Vacutec Ion Chamber
6695--21
AID Ion Chamber
6695--11
Medys Ion Chamber
6695--66
6695--56
6695--57

2B3
Tray Blockage
SAT--28213--01
2B4
Grid Blockage
A525510--01
2B5
Switch Kit BDC
A520491--01
2B6
Grid Guides BDC Kit
A520492--01
Includes ITEM 2B4
2B7
Rubber Bumper
SAT--6533--01
This reference comprises 5 units
2B8
Handle Kit
SAT--A10634--02
2B9
Ball Bearing Slide
SAT--54505012
2B10
Cable Support
SAT--53530150
26
Includes 10 Units
SM-1103R3

Service Manual
2B1
2B2
2B6
2B5
2B7
2B9
2B3
2B4
2B10
SM-1103R3
2B8
27

Service Manual
ITEM
3B
3B1
3B2
DESCRIPTION
QTY
REFERENCE
DETECTOR CABINET WITH ROTATING TRAY

SAT--A10521--01
SAT--A9657--02
SAT--A10523--01
SAT--A9656--02
SAT--A10522--01
SAT--A10667--01
SAT--A10666--01
SAT--A10665--01
SAT--A10664--01
SAT--A10663--01
SAT--A10667--02
SAT--A10666--02
SAT--A10665--02
SAT--A10664--02
SAT--A10663--02
Vacutec Ion Chamber
6695--21
AID Ion Chamber
6695--11
Medys Ion Chamber
6695--66
6695--56
6695--57

3B3
Rear bumper Kit
SAT--A10676--02
3B4
Detector Detent Kit
SAT--A10677--01
3B5
Switch Kit BCG
A520490--01
3B6
Bumper Rubber
SAT--6533--01
3B7
Grid Blockage
A520476--01
3B8
Grid Guides BDG Kit
A520493--01
3B9
Handle Kit
SAT--A10634--11
3B10
Holder for Detector
SAT--A10904--01
3B11
Ball Bearing Slide
SAT--54505012
3B12
Cable Support
SAT--53530150
3B13
Turning Kit
SAT--A10654--01
28
REMARKS
Includes ITEM 3B7
Only for detector without handle
Includes 10 Units
SM-1103R3

Service Manual
3B6
3B5
3B8
3B7
3B1
3B2
3B11
3B12
3B3
3B9
3B10
3B13
SM-1103R3
F4
29

Service Manual
ITEM
4B
4B1
4B2
DESCRIPTION
QTY
REFERENCE
DETECTOR CABINET FIXED DETECTOR AND REMOVABLE GRID

SAT--A10521--01
SAT--A9657--02
SAT--A10523--01
SAT--A9656--02
SAT--A10522--01
SAT--A10667--01
SAT--A10666--01
SAT--A10665--01
SAT--A10664--01
SAT--A10663--01
SAT--A10667--02
SAT--A10666--02
SAT--A10665--02
SAT--A10664--02
SAT--A10663--02
Vacutec Ion Chamber
6695--21
AID Ion Chamber
6695--11
Medys Ion Chamber
6695--66
6695--56
6695--57

4B3
Switch Kit BDC
A520491--01
4B4
Bumper Rubber
SAT--6533--01
4B5
Grid Blockage
A520476--01
4B6
Fans Kit
SAT--A9721--01
30
REMARKS
SM-1103R3

Service Manual
4B4
4B3
4B5
4B2
4B1
4B6
SM-1103R3
31

Service Manual
32
SM-1103R3

Service Manual
SECTION 8
SYSTEM INTERCONNECTION MAPS

Refer to the following maps for details of the wire connections.
SYSTEM INTERCONNECTION
Note
SM-1103R3
General Purpose Rad System Interconnection . . . . . . . . . IM--341
Radiographic Table Interconnections . . . . . . . . . . . . . . . . . 54303079
For System Interconnection Maps I/F-001, I/F-003, I/F-045,

IM-015 refer to Generator Service Manual -- Installation Chapter.
33

Service Manual
34
SM-1103R3
ROT MOBILE COLUMN
Note 2.- Cable code:

A3052-XX for only Low Speed
A7014-XX for Low/High Speed
See schematic 54301085

for interconnections
TUBE STATOR CABLE (See Note 2)
X-RAY
TUBE
TS2
C
TS1
VAC SUPPLY
GENERATOR SUPPLY CABLE (See Note 1)
AC LINE
Chassis
GND
COLLIMATOR CABLE (A3111-XX)
COLLIMATOR
GND CABLE (A6383-XX)
Chassis
GND

A8410-01 for Compact Generator - single phase
A8411-01 for Compact Generator - three phase
A8412-01 for Battery Generator
A8413-01 for Capacitor Generator
HV
TANK
ANODE CABLE
GENERATOR CABINET
CATHODE CABLE
TB7
SUPPLY CABLE (A6736-XX)
LOCKS
BOARD
TB7
RAD TABLE
3

TS1
Note 3:
AEC CABLE, AEC INTERFACE CABLE AND
AEC ADAPTATION BOARD NOT USED FOR
RAD ROOM STANDARD (without ION
CHAMBER)
Chassis
GND
Chassis
GND
GENERATOR CONSOLE
BUCKY
TABLE BUCKY CABLE (A3091-XX)
See schematic I/F-001
AEC ADAPTATION BOARD

(A3263-03)
TS1
See schematic IM-015

AEC CABLE (A3253-XX)
ION CHAMBER
(Preamplifier)
J1,J2,J3
(See Note 3)
(See Note 3)
ATP CONSOLE BOARD

AEC INTERFACE CABLE (A3251-XX)
J4
TB1
(See Note 3)
J2
ION CHAMBER
(Preamplifier)
(See Note 3)
(See Note 3)
WALL BUCKY CABLE (A6703-XX)
BUCKY

Chassis
GND
J3
(See Note 3)
POWER I/F CABLE (A3252-03)
VERTICAL BUCKY
J5
(See Note 3)
TS1/TS3
POWER CABLE (A7021-XX)
J1
COMMUNICATION CABLE (A7022-XX)
J3
INTERFACE CABLE (A7069-XX)
J2
Chassis
GND
Chassis
GND
TS1
Chassis
GND
THIS SHEET ONLY APPLIES with CONVENTIONAL CONSOLE
new interface
F. Garca
10/10/05
new interface
F. Garca
30/11/04
REV
DESCRIPTION
ISSUED BY
DATE
NAME
DATE
DRAWING
F.GARCIA
05/05/04
REVISED
A.DIAZ
02/06/04
SEDECAL
D
SHEET / OF
IM - 341
1/2
RAD ROOM STANDARD

& with AEC SYSTEM
E
REV
ROT MOBILE COLUMN

A3052-XX for only Low Speed
A7014-XX for Low/High Speed

TUBE STATOR CABLE (See Note 2)
X-RAY
TUBE
TS2
C
A
Chassis
GND
TS1
GENERATOR SUPPLY CABLE (See Note 1)
AC LINE
COLLIMATOR CABLE (A3111-XX)
COLLIMATOR
VAC SUPPLY
Chassis
GND

A8410-01 for Compact Generator - single phase
A8411-01 for Compact Generator - three phase
A8412-01 for Battery Generator
A8413-01 for Capacitor Generator
HV
TANK
ANODE CABLE
GENERATOR CABINET
CATHODE CABLE
LOCKS
BOARD
TB7
TB7
RAD TABLE
3

TS1
Chassis
GND
Chassis
GND
BUCKY
TABLE BUCKY CABLE (A3091-XX)
TS1
ATP CONSOLE BOARD
ION CHAMBER
(Preamplifier)
J5
(See Note 3)
(See Note 3)
Note 3:
AEC CABLE, AEC INTERFACE CABLE AND
AEC ADAPTATION BOARD NOT USED FOR
RAD ROOM STANDARD (without ION
CHAMBER)
AEC INTERFACE CABLE (A3251-02)

(See Note 3)
2
AEC ADAPTATION BOARD

(A3263-03)
VERTICAL BUCKY
See schematic IM-015

ION CHAMBER
(Preamplifier)
J1,J2,J3
(See Note 3)
(See Note 3)
GENERATOR CONSOLE
(TOUCH SCREEN)
J4
INTERFACE BOX CABLE (A7067-XX)
J5
TB1
(See Note 3)
TPC SUPPLY CABLE (A7059-XX)
TS1
WALL BUCKY CABLE (A6703-XX)
BUCKY

Chassis
GND
TS1
POWER I/F CABLE (A3252-03)
AC-SUPPLY
Chassis
GND
(See Note 3)
GENERATOR
Chassis
GND
Chassis
GND
THIS SHEET ONLY APPLIES with TPC/SERIAL CONSOLE
new interface
F. Garca
10/10/05
new interface
F. Garca
30/11/04
REV
DESCRIPTION
ISSUED BY
DATE
NAME
DATE
DRAWING
F.GARCIA
05/05/04
REVISED
A.DIAZ
02/06/04
SEDECAL
D
SHEET / OF
IM - 341
2/2
RAD ROOM STANDARD

& with AEC SYSTEM
E
REV

TXR Multirad Table SM 1103r3i

Uploaded by

Copyright:

Available Formats

TXR Multirad Table SM 1103r3i

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TXR Multirad Table SM 1103r3i

Uploaded by

Copyright:

Available Formats

What is the product that this manual is describing?

What is the product that this manual is describing?

What safety symbols may appear on the equipment?

What safety symbols may appear on the equipment?

Technical Publication

The information comprised in this manual applies to the following equipments

MULT-FWFTT Four-Ways Floating Top Table MULTIRAD

Fax: +34 902 190 385

General Purpose Rad Table

REASON FOR CHANGE

MAY 23, 2011

AUG 09, 2013

SEPT 09, 2013

NOV 05, 2013

Ammended distance of anchoring holes

General Purpose Rad Table

DANGERS ADVISE OF CONDITIONS OR SITUATIONS THAT

ADVISE OF CONDITIONS OR SITUATIONS THAT IF NOT

Advise of conditions or situations that if not heeded or

Alert readers to pertinent facts and conditions. Notes represent

General Purpose Rad Table

Caution. Consult accompanying documents.

Safety Symbol. Follow instructions for use, especially those

General Mandatory action.

Type B applied part.

Protection against harmful ingress of water or particulate matter.

Non-ionizing electromagnetic radiation.

Radiation of Laser apparatus.

General Purpose Rad Table

General warning, caution, risk of danger.

Warning: Ionizing radiation.

Warning: Non-ionizing radiation.

Warning: Laser beam.

Warning: Dangerous voltage.

Electrostatic sensitive devices.

General Purpose Rad Table

Stop (of action).

Three-phase alternating current.

Three-phase alternating current with neutral conductor.

Connection point for the neutral conductor on Permanently Installed equipment.

General Purpose Rad Table

Both direct and alternating current.

Protective Earth (Ground).

General Purpose Rad Table

Objective and Scope of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Responsibilities of the Purchaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Undertable Installation of the Generator (option) . . . . . . . . . . . . . . . . . . . . . . . .

Pedal Microswitch Replacing and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance Activities Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking of Radiographic Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Check Off Maintenance Revision Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SYSTEM INTERCONNECTION MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Purpose Rad Table

General Purpose Rad Table

OBJECTIVE AND SCOPE OF THIS MANUAL

OPERATOR AND SERVICE MANUALS SHOULD BE

TOOLS AND TEST EQUIPMENT