IMO2008 - MSC267 (85) - 2008 IS Code PDF

MSC 85/26/Add.
1
ANNEX 2
RESOLUTION MSC.267(85)
(adopted on 4 December 2008)
ADOPTION OF THE INTERNATIONAL CODE ON INTACT STABILITY, 2008
(2008 IS CODE)
THE MARITIME SAFETY COMMITTEE,
RECALLING Article 28(b) of the Convention on the International Maritime Organization
concerning the functions of the Committee,
RECALLING ALSO resolution A.749(18) entitled Code on Intact Stability for All
Types of Ships Covered by IMO Instruments, as amended by resolution MSC.75(69),
RECOGNIZING the need to update the aforementioned Code and the importance of
establishing mandatory international intact stability requirements,
NOTING resolutions MSC.269(85) and MSC.270(85), by which it adopted, inter alia,
amendments to the International Convention for the Safety of Life at Sea (SOLAS), 1974,
as amended (hereinafter referred to as the 1974 SOLAS Convention) and to the Protocol
of 1988 relating to the International Convention on Load Lines, 1966 (hereinafter referred to as
the 1988 Load Lines Protocol), respectively, to make the introduction and the provisions of
part A of the International Code on Intact Stability, 2008 mandatory under the 1974 SOLAS
Convention and the 1988 Load Lines Protocol,
HAVING CONSIDERED, at its eighty-fifth session, the text of the proposed International
Code on Intact Stability, 2008,
1.
ADOPTS the International Code on Intact Stability, 2008 (2008 IS Code), the text of
which is set out in the Annex to the present resolution;
2.
INVITES Contracting Governments to the 1974 SOLAS Convention and Parties to
the 1988 Load Lines Protocol to note that the 2008 IS Code will take effect on 1 July 2010
upon the entry into force of the respective amendments to the 1974 SOLAS Convention
and 1988 Load Lines Protocol;
3.
REQUESTS the Secretary-General to transmit certified copies of the present resolution
and the text of the 2008 IS Code contained in the Annex to all Contracting Governments to
the 1974 SOLAS Convention and Parties to the 1988 Load Lines Protocol;
4.
FURTHER REQUESTS the Secretary-General to transmit copies of this resolution and
the Annex to all Members of the Organization which are not Contracting Governments to
the 1974 SOLAS Convention or Parties to the 1988 Load Lines Protocol;
5.
RECOMMENDS Governments concerned to use the recommendatory provisions
contained in part B of the 2008 IS Code as a basis for relevant safety standards, unless their
national stability requirements provide at least an equivalent degree of safety.
I:\MSC\85\26-Add-1.doc
MSC 85/26/Add.1
ANNEX 2
Page 2
ANNEX
INTERNATIONAL CODE ON INTACT STABILITY, 2008
(2008 IS CODE)
CONTENTS
PREAMBLE
INTRODUCTION
1
Purpose
2
Definitions
PART A
MANDATORY CRITERIA
Chapter 1 General
1.1
Application
1.2
Dynamic stability phenomena in waves
Chapter 2 General criteria
2.1
General
2.2
Criteria regarding righting lever curve properties
2.3
Severe wind and rolling criterion (weather criterion)
Chapter 3
3.1
3.2
3.3
3.4
3.5
Special criteria for certain types of ships

Passenger ships
Oil tankers of 5,000 dwt and above
Cargo ships carrying timber deck cargoes
Cargo ships carrying grain in bulk
High-speed craft
PART B
RECOMMENDATIONS FOR CERTAIN TYPES OF SHIPS AND

ADDITIONAL GUIDELINES
Chapter 1 General
1.1
Purpose
1.2
Application
Chapter 2
2.1
2.2
2.3
2.4
2.5
2.6
Recommended design criteria for certain types of ships

Fishing vessels
Pontoons
Containerships greater than 100 m
Offshore supply vessels
Special purpose ships
Mobile offshore drilling units (MODUs)
MSC 85/26/Add.1
ANNEX 2
Page 3
Chapter 3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
Guidance in preparing stability information

Effect of free surfaces of liquids in tanks
Permanent ballast
Assessment of compliance with stability criteria
Standard conditions of loading to be examined
Calculation of stability curves
Stability booklet
Operational measures for ships carrying timber deck cargoes
Operating booklets for certain ships
Chapter 4
4.1
Stability calculations performed by stability instruments

Stability instruments
Chapter 5 Operational provisions against capsizing

5.1
General precautions against capsizing
5.2
Operational precautions in heavy weather
5.3
Ship handling in heavy weather
Chapter 6 Icing considerations
6.1
General
6.2
6.3
Fishing vessels
6.4
Offshore supply vessels 24 m to 100 m in length
Chapter 7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
Considerations for watertight and weathertight integrity

Hatchways
Machinery space openings
Doors
Cargo ports and other similar openings
Sidescuttles, window scuppers, inlets and discharges
Other deck openings
Ventilators, air pipes and sounding devices
Freeing ports
Miscellaneous
Chapter 8
8.1
8.2
8.3
8.4
8.5
8.6
Determination of lightship parameters

Application
Preparations for the inclining test
Plans required
Test procedure
Inclining test for MODUs
Stability test for pontoons
MSC 85/26/Add.1
ANNEX 2
Page 4
Annex 1 Detailed guidance for the conduct of an inclining test
1
Introduction
2
2.1
Free surface and tankage
2.2
Mooring arrangements
2.3
Test weights
2.4
Pendulums
2.5
U-tubes
2.6
Inclinometers
3
Equipment required
4
Test procedure
4.1
Initial walk through and survey
4.2
Freeboard/draught readings
4.3
The incline
Annex 2
1
2
3
4
Recommendations for skippers of fishing vessels on ensuring

a vessels endurance in conditions of ice formation
Prior to departure
At sea
During ice formation
List of equipment and hand tools
MSC 85/26/Add.1
ANNEX 2
Page 5
PREAMBLE
1
This Code has been assembled to provide, in a single document, mandatory requirements
in the introduction and in part A and recommended provisions in part B relating to intact
stability, based primarily on existing IMO instruments. Where recommendations in this Code
appear to differ from other IMO Codes, the other Codes should be taken as the prevailing
instrument. For the sake of completeness and for the convenience of the user, this Code also
contains relevant provisions from mandatory IMO instruments.
2
Criteria included in the Code are based on the best state-of-the-art concepts, available at
the time they were developed, taking into account sound design and engineering principles and
experience gained from operating ships. Furthermore, design technology for modern ships is
rapidly evolving and the Code should not remain static but should be re-evaluated and revised,
as necessary. To this end, the Organization will periodically review the Code taking into
consideration both experience and further development.
3
A number of influences such as the dead ship condition, wind on ships with large
windage area, rolling characteristics, severe seas, etc., were taken into account based on the
state-of-the-art technology and knowledge at the time of the development of the Code.
4
It was recognized that in view of a wide variety of types, sizes of ships and their operating
and environmental conditions, problems of safety against accidents related to stability have
generally not yet been solved. In particular, the safety of a ship in a seaway involves complex
hydrodynamic phenomena which up to now have not been fully investigated and understood.
Motion of ships in a seaway should be treated as a dynamical system and relationships between
ship and environmental conditions like wave and wind excitations are recognized as extremely
important elements. Based on hydrodynamic aspects and stability analysis of a ship in a seaway,
stability criteria development poses complex problems that require further research.
MSC 85/26/Add.1
ANNEX 2
Page 6
INTRODUCTION
1
Purpose
1.1
The purpose of the Code is to present mandatory and recommendatory stability criteria
and other measures for ensuring the safe operation of ships, to minimize the risk to such ships,
to the personnel on board and to the environment. This introduction and part A of the Code
address the mandatory criteria and part B contains recommendations and additional guidelines.
1.2
This Code contains intact stability criteria for the following types of ships and other
marine vehicles of 24 m in length and above, unless otherwise stated:
.1
cargo ships;
.2
cargo ships carrying timber deck cargoes;
.3
passenger ships;
.4
fishing vessels;
.5
special purpose ships;
.6
offshore supply vessels;
.7
mobile offshore drilling units;
.8
pontoons; and
.9
cargo ships carrying containers on deck and containerships.
1.3
Administrations may impose additional requirements regarding the design aspects of
ships of novel design or ships not otherwise covered by the Code.
2
Definitions
For the purpose of this Code the definitions given hereunder shall apply. For terms used, but not
defined in this Code, the definitions as given in the 1974 SOLAS Convention, as amended, shall
apply.
2.1
Administration means the Government of the State whose flag the ship is entitled to fly.
2.2
Passenger ship is a ship which carries more than twelve passengers as defined in
regulation I/2 of the 1974 SOLAS Convention, as amended.
2.3
Cargo ship is any ship which is not a passenger ship, a ship of war and troopship, a ship
which is not propelled by mechanical means, a wooden ship of primitive build, a fishing vessel or
a mobile offshore drilling unit.
2.4
Oil tanker means a ship constructed or adapted primarily to carry oil in bulk in its cargo
spaces and includes combination carriers and any chemical tanker as defined in Annex II of
the MARPOL Convention when it is carrying a cargo or part cargo of oil in bulk.
MSC 85/26/Add.1
ANNEX 2
Page 7
2.4.1
Combination carrier means a ship designed to carry either oil or solid cargoes in bulk.
2.4.2
Crude oil tanker means an oil tanker engaged in the trade of carrying crude oil.
2.4.3 Product carrier means an oil tanker engaged in the trade of carrying oil other than
crude oil.
2.5
Fishing vessel is a vessel used for catching fish, whales, seals, walrus or other living
resources of the sea.
2.6
Special purpose ship has the same definition as in the Code of Safety for Special Purpose
Ships, 2008 (resolution MSC.266(84)).
2.7
Offshore supply vessel means a vessel which is engaged primarily in the transport of
stores, materials and equipment to offshore installations and designed with accommodation and
bridge erections in the forward part of the vessel and an exposed cargo deck in the after part for
the handling of cargo at sea.
2.8
Mobile offshore drilling unit (MODU or unit) is a ship capable of engaging in drilling
operations for the exploration or exploitation of resources beneath the sea-bed such as liquid or
gaseous hydrocarbons, sulphur or salt.
2.8.1 Column-stabilized unit is a unit with the main deck connected to the underwater hull or
footings by columns or caissons.
2.8.2 Surface unit is a unit with a ship- or barge-type displacement hull of single or multiple
hull construction intended for operation in the floating condition.
2.8.3 Self-elevating unit is a unit with moveable legs capable of raising its hull above the
surface of the sea.
2.8.4 Coastal State means the Government of the State exercising administrative control over
the drilling operations of the unit.
2.8.5 Mode of operation means a condition or manner in which a unit may operate or function
while on location or in transit. The modes of operation of a unit include the following:
.1
operating conditions means conditions wherein a unit is on location for the

purpose of conducting drilling operations, and combined environmental and
operational loadings are within the appropriate design limits established for such
operations. The unit may be either afloat or supported on the sea-bed,
as applicable;
.2
severe storm conditions means conditions wherein a unit may be subjected to the
most severe environmental loadings for which the unit is designed. Drilling
operations are assumed to have been discontinued due to the severity of the
environmental loadings, the unit may be either afloat or supported on the sea-bed,
as applicable; and
.3
transit conditions means conditions wherein a unit is moving from one

geographical location to another.
MSC 85/26/Add.1
ANNEX 2
Page 8
2.9
High-speed craft (HSC)1 is a craft capable of a maximum speed, in metres per second (m/s),
equal to or exceeding:
3.7 * 0.1667
where: = displacement corresponding to the design waterline (m).
2.10
Containership means a ship which is used primarily for the transport of marine containers.
2.11
Freeboard is the distance between the assigned load line and freeboard deck2.
2.12 Length of ship. The length should be taken as 96% of the total length on a waterline
at 85% of the least moulded depth measured from the top of the keel, or as the length from the
fore side of the stem to the axis of the rudder stock on the waterline, if that be greater. In ships
designed with a rake of keel the waterline on which this length is measured should be parallel to
the designed waterline.
2.13 Moulded breadth is the maximum breadth of the ship measured amidships to the moulded
line of the frame in a ship with a metal shell and to the outer surface of the hull in a ship with a
shell of any other material.
2.14 Moulded depth is the vertical distance measured from the top of the keel to the top of the
freeboard deck beam at side. In wood and composite ships, the distance is measured from the
lower edge of the keel rabbet. Where the form at the lower part of the midship section is of a
hollow character, or where thick garboards are fitted, the distance is measured from the point
where the line of the flat of the bottom continued inwards cuts the side of the keel. In ships having
rounded gunwales, the moulded depth should be measured to the point of intersection of the
moulded lines of the deck and side shell plating, the lines extending as though the gunwale were
of angular design. Where the freeboard deck is stepped and the raised part of the deck extends
over the point at which the moulded depth is to be determined, the moulded depth should be
measured to a line of reference extending from the lower part of the deck along a line parallel
with the raised part.
2.15 Near-coastal voyage means a voyage in the vicinity of the coast of a State as defined by
the Administration of that State.
The Code of Safety for High-Speed Craft, 2000 (2000 HSC Code) has been developed following a thorough
revision of the Code of Safety for High-Speed Craft, 1994 (1994 HSC Code) which was derived from the
previous Code of Safety for Dynamically Supported Craft (DSC Code) adopted by IMO in 1977, recognizing
that safety levels can be significantly enhanced by the infrastructure associated with regular service on a
particular route, whereas the conventional ship safety philosophy relies on the ship being self-sustaining with all
necessary emergency equipment being carried on board.
For the purposes of application of chapters I and II of Annex I of the International Convention on Load
Lines, 1966 or the Protocol of 1988 as amended, as applicable to open-top containerships, freeboard deck
is the freeboard deck according to the International Convention on Load Lines, 1966 or the Protocol of 1988
as amended, as applicable as if hatch covers are fitted on top of the hatch cargo coamings.
MSC 85/26/Add.1
ANNEX 2
Page 9
2.16
Pontoon is considered to be normally:

.1
non self-propelled;
.2
unmanned;
.3
carrying only deck cargo;
.4
having a block coefficient of 0.9 or greater;
.5
having a breadth/depth ratio of greater than 3; and
.6
having no hatchways in the deck except small manholes closed with gasketed
covers.
2.17 Timber means sawn wood or lumber, cants, logs, poles, pulpwood and all other types of
timber in loose or packaged forms. The term does not include wood pulp or similar cargo.
2.18 Timber deck cargo means a cargo of timber carried on an uncovered part of a freeboard or
superstructure deck. The term does not include wood pulp or similar cargo.3
2.19 Timber load line means a special load line assigned to ships complying with certain
conditions related to their construction set out in the International Convention on Load Lines and
used when the cargo complies with the stowage and securing conditions of the Code of Safe
Practice for Ships Carrying Timber Deck Cargoes, 1991 (resolution A.715(17)).
2.20 Certification of the inclining test weights is the verification of the weight marked on a test
weight. Test weights should be certified using a certificated scale. The weighing should be
performed close enough in time to the inclining test to ensure the measured weight is accurate.
2.21
Draught is the vertical distance from the moulded baseline to the waterline.
2.22 The inclining test involves moving a series of known weights, normally in the transverse
direction, and then measuring the resulting change in the equilibrium heel angle of the ship.
By using this information and applying basic naval architecture principles, the ships vertical
centre of gravity (VCG) is determined.
2.23 Lightship condition is a ship complete in all respects, but without consumables, stores,
cargo, crew and effects, and without any liquids on board except that machinery and piping
fluids, such as lubricants and hydraulics, are at operating levels.
2.24 A lightweight survey involves taking an audit of all items which should be added,
deducted or relocated on the ship at the time of the inclining test so that the observed condition of
the ship can be adjusted to the lightship condition. The mass, longitudinal, transverse and
vertical location of each item should be accurately determined and recorded. Using this
information, the static waterline of the ship at the time of the inclining test as determined from
measuring the freeboard or verified draught marks of the ship, the ships hydrostatic data, and the
3
Refer to regulation 42(1) of the International Convention on Load Lines, 1966 or the Protocol of 1988
as amended, as applicable.
MSC 85/26/Add.1
ANNEX 2
Page 10
sea water density, the lightship displacement and longitudinal centre of gravity (LCG) can be
obtained. The transverse centre of gravity (TCG) may also be determined for mobile offshore
drilling units (MODUs) and other ships which are asymmetrical about the centreline or whose
internal arrangement or outfitting is such that an inherent list may develop from off-centre mass.
2.25 An in-service inclining test means an inclining test which is performed in order to verify
the pre-calculated GMC and the deadweights centre of gravity of an actual loading condition.
2.26 A stability instrument is an instrument installed on board a particular ship by means of
which it can be ascertained that stability requirements specified for the ship in the Stability
Booklet are met in any operational loading condition. A Stability Instrument comprises hardware
and software.
MSC 85/26/Add.1
ANNEX 2
Page 11
PART A
MANDATORY CRITERIA
CHAPTER 1
1.1
GENERAL
Application
1.1.1 The criteria stated under chapter 2 of this part present a set of minimum requirements that
shall apply to cargo4 and passenger ships of 24 m in length and over.
1.1.2 The criteria stated under chapter 3 are special criteria for certain types of ships. For the
purpose of part A the definitions given in the Introduction apply.
1.2
Dynamic stability phenomena in waves
Administrations shall be aware that some ships are more at risk of encountering critical stability
situations in waves. Necessary precautionary provisions may need to be taken in the design to
address the severity of such phenomena. The phenomena in seaways which may cause large roll
angles and/or accelerations have been identified hereunder.
Having regard to the phenomena described in this section, the Administration may for a
particular ship or group of ships apply criteria demonstrating that the safety of the ship is
sufficient. Any Administration which applies such criteria should communicate to the
Organization particulars thereof. It is recognized by the Organization that performance oriented
criteria for the identified phenomena listed in this section need to be developed and implemented
to ensure a uniform international level of safety.
1.2.1
Righting lever variation
Any ship exhibiting large righting lever variations between wave trough and wave crest condition
may experience parametric roll or pure loss of stability or combinations thereof.
1.2.2
Resonant roll in dead ship condition
Ships without propulsion or steering ability may be endangered by resonant roll while drifting
freely.
1.2.3
Broaching and other manoeuvring related phenomena
Ships in following and quartering seas may not be able to keep constant course despite maximum
steering efforts which may lead to extreme angles of heel.
For containerships of 100 m in length and over, provisions of chapter 2.3 of part B may be applied as an
alternative to the application of chapter 2.2 of this part. Offshore supply vessels and special purpose ships are
not required to comply with provisions of chapter 2.3 of part A. For offshore supply vessels, provisions of
chapter 2.4 of part B may be applied as an alternative to the application of chapter 2.2 of this part. For special
purpose ships, provisions of chapter 2.5 of part B may be applied as an alternative to the application of
chapter 2.2 of this part.
MSC 85/26/Add.1
ANNEX 2
Page 12
CHAPTER 2
GENERAL CRITERIA
2.1
General
2.1.1
All criteria shall be applied for all conditions of loading as set out in part B, 3.3 and 3.4.
2.1.2 Free surface effects (part B, 3.1) shall be accounted for in all conditions of loading as set
out in part B, 3.3 and 3.4.
2.1.3 Where anti-rolling devices are installed in a ship, the Administration shall be satisfied that
the criteria can be maintained when the devices are in operation and that failure of power supply
or the failure of the device(s) will not result in the vessel being unable to meet the relevant
provisions of this Code.
2.1.4 A number of influences such as icing of topsides, water trapped on deck, etc., adversely
affect stability and the Administration is advised to take these into account, so far as is deemed
necessary.
2.1.5 Provisions shall be made for a safe margin of stability at all stages of the voyage, regard
being given to additions of weight, such as those due to absorption of water and icing (details
regarding ice accretion are given in part B, chapter 6 Icing considerations) and to losses of
weight such as those due to consumption of fuel and stores.
2.1.6 Each ship shall be provided with a stability booklet, approved by the Administration,
which contains sufficient information (see part B, 3.6) to enable the master to operate the ship in
compliance with the applicable requirements contained in the Code. If a stability instrument is
used as a supplement to the stability booklet for the purpose of determining compliance with the
relevant stability criteria such instrument shall be subject to the approval by the Administration
(see part B, chapter 4 Stability calculations performed by stability instruments).
2.1.7 If curves or tables of minimum operational metacentric height (GM) or maximum centre
of gravity (VCG) are used to ensure compliance with the relevant intact stability criteria those
limiting curves shall extend over the full range of operational trims, unless the Administration
agrees that trim effects are not significant. When curves or tables of minimum operational
metacentric height (GM) or maximum centre of gravity (VCG) versus draught covering the
operational trims are not available, the master must verify that the operating condition does not
deviate from a studied loading condition, or verify by calculation that the stability criteria are
satisfied for this loading condition taking into account trim effects.
2.2
Criteria regarding righting lever curve properties
2.2.1 The area under the righting lever curve (GZ curve) shall not be less
than 0.055 metre-radians up to = 30 angle of heel and not less than 0.09 metre-radians up
to = 40 or the angle of down-flooding f5 if this angle is less than 40. Additionally, the area
under the righting lever curve (GZ curve) between the angles of heel of 30 and 40 or
between 30 and f, if this angle is less than 40, shall not be less than 0.03 metre-radians.
f is an angle of heel at which openings in the hull, superstructures or deckhouses which cannot be closed
weathertight immerse. In applying this criterion, small openings through which progressive flooding cannot
take place need not be considered as open.
MSC 85/26/Add.1
ANNEX 2
Page 13
2.2.2 The righting lever GZ shall be at least 0.2 m at an angle of heel equal to or greater
than 30.
2.2.3 The maximum righting lever shall occur at an angle of heel not less than 25. If this is
not practicable, alternative criteria, based on an equivalent level of safety6, may be applied
subject to the approval of the Administration.
2.2.4
The initial metacentric height GM0 shall not be less than 0.15 m.
2.3
Severe wind and rolling criterion (weather criterion)
2.3.1 The ability of a ship to withstand the combined effects of beam wind and rolling shall be
demonstrated, with reference to figure 2.3.1 as follows:
.1
the ship is subjected to a steady wind pressure acting perpendicular to the ships
centreline which results in a steady wind heeling lever (lw1);
.2
from the resultant angle of equilibrium (0), the ship is assumed to roll owing to
wave action to an angle of roll (1) to windward. The angle of heel under action
of steady wind (0) should not exceed 16 or 80% of the angle of deck edge
immersion, whichever is less;
.3
the ship is then subjected to a gust wind pressure which results in a gust wind
heeling lever (lw2); and
.4
under these circumstances, area b shall be equal to or greater than area a,

as indicated in figure 2.3.1 below:
Figure 2.3.1 Severe wind and rolling
Refer to the Explanatory Notes to the International Code on Intact Stability, 2008 (MSC.1/Circ.1281).
MSC 85/26/Add.1
ANNEX 2
Page 14
where the angles in figure 2.3.1 are defined as follows:
0 = angle of heel under action of steady wind
1 = angle of roll to windward due to wave action (see 2.3.1.2, 2.3.4 and
footnote 6)
2 = angle of down-flooding (f) or 50 or c, whichever is less,
where:
f = angle of heel at which openings in the hull, superstructures or
deckhouses which cannot be closed weathertight immerse.
In applying this criterion, small openings through which progressive
flooding cannot take place need not be considered as open
c = angle of second intercept between wind heeling lever lw2 and
GZ curves.
2.3.2 The wind heeling levers lw1 and lw2 referred to in 2.3.1.1 and 2.3.1.3 are constant values at
all angles of inclination and shall be calculated as follows:
P A Z
(m) and
1000 g
= 1.5 l w1 (m)
l w1 =
l w2
where:
P = wind pressure of 504 Pa. The value of P used for ships in restricted
service may be reduced subject to the approval of the Administration
A = projected lateral area of the portion of the ship and deck cargo above the
waterline (m2)
Z = vertical distance from the centre of A to the centre of the underwater
lateral area or approximately to a point at one half the mean draught (m)
= displacement (t)
g
= gravitational acceleration of 9.81 m/s2.
2.3.3 Alternative means for determining the wind heeling lever (lw1) may be accepted, to the
satisfaction of the Administration, as an equivalent to calculation in 2.3.2. When such alternative
tests are carried out, reference shall be made based on the Guidelines developed by the
Organization7. The wind velocity used in the tests shall be 26 m/s in full scale with uniform
velocity profile. The value of wind velocity used for ships in restricted services may be reduced
to the satisfaction of the Administration.
7
Refer to the Interim Guidelines for alternative assessment of the weather criterion (MSC.1/Circ.1200).
MSC 85/26/Add.1
ANNEX 2
Page 15
2.3.4
The angle of roll (1)8 referred to in 2.3.1.2 shall be calculated as follows:
1 = 109 k X 1 X 2 r s (degrees)
where:
X1
= factor as shown in table 2.3.4-1
X2
= factor as shown in table 2.3.4-2
= factor as follows:
= 1.0 for round-bilged ship having no bilge or bar keels
= 0.7 for a ship having sharp bilges
= as shown in table 2.3.4-3 for a ship having bilge keels, a bar keel
or both
= 0.73 + 0.6 OG/d

with:
OG = KG d
d
= mean moulded draught of the ship (m)
= factor as shown in table 2.3.4-4, where T is the ship roll natural period.
In absence of sufficient information, the following approximate formula
can be used:
Rolling period
T=
2*C * B
GM
( s)
where:
C = 0.373 + 0.023(B/d) - 0.043(Lwl/100).
The symbols in tables 2.3.4-1, 2.3.4-2, 2.3.4-3 and 2.3.4-4 and the formula for the
rolling period are defined as follows:
Lwl = length of the ship at waterline (m)
B
= moulded breadth of the ship (m)
The angle of roll for ships with anti-rolling devices should be determined without taking into account the
operation of these devices unless the Administration is satisfied with the proof that the devices are effective
even with sudden shutdown of their supplied power.
MSC 85/26/Add.1
ANNEX 2
Page 16
d
= mean moulded draught of the ship (m)
CB = block coefficient (-)

Ak
= total overall area of bilge keels, or area of the lateral projection of the bar
keel, or sum of these areas (m)
GM = metacentric height corrected for free surface effect (m).

Table 2.3.4-1 Values of factor X1
B/d
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.4
3.5
X1
1.0
0.98
0.96
0.95
0.93
0.91
0.90
0.88
0.86
0.82
0.80
Table 2.3.4-2 Values of factor X2

CB
0.45
0.50
0.55
0.60
0.65
0.70
X2
0.75
0.82
0.89
0.95
0.97
1.00
Table 2.3.4-3 Values of factor k

Ak 100
LWL B
0
1.0
1.5
2.0
2.5
3.0
3.5
4.0
k
1.0
0.98
0.95
0.88
0.79
0.74
0.72
0.70
MSC 85/26/Add.1
ANNEX 2
Page 17
Table 2.3.4-4 Values of factor s
T
6
7
8
12
14
16
18
20
s
0.100
0.098
0.093
0.065
0.053
0.044
0.038
0.035
(Intermediate values in these tables shall be obtained by linear interpolation)

2.3.5
The tables and formulae described in 2.3.4 are based on data from ships having:
.1
B/d smaller than 3.5;
.2
(KG/d-1) between - 0.3 and 0.5; and
.3
T smaller than 20 s.
For ships with parameters outside of the above limits the angle of roll (1) may be determined
with model experiments of a subject ship with the procedure described in MSC.1/Circ.1200 as
the alternative. In addition, the Administration may accept such alternative determinations for
any ship, if deemed appropriate.
MSC 85/26/Add.1
ANNEX 2
Page 18
CHAPTER 3
3.1
SPECIAL CRITERIA FOR CERTAIN TYPES OF SHIPS
Passenger ships
Passenger ships shall comply with the requirements of 2.2 and 2.3.
3.1.1 In addition, the angle of heel on account of crowding of passengers to one side as defined
below shall not exceed 10.
3.1.1.1 A minimum weight of 75 kg shall be assumed for each passenger except that this value
may be increased subject to the approval of the Administration. In addition, the mass and
distribution of the luggage shall be approved by the Administration.
3.1.1.2 The height of the centre of gravity for passengers shall be assumed equal to:
.1
1 m above deck level for passengers standing upright. Account may be taken,
if necessary, of camber and sheer of deck; and
.2
0.3 m above the seat in respect of seated passengers.
3.1.1.3 Passengers and luggage shall be considered to be in the spaces normally at their
disposal, when assessing compliance with the criteria given in 2.2.1 to 2.2.4.
3.1.1.4 Passengers without luggage shall be considered as distributed to produce the most
unfavourable combination of passenger heeling moment and/or initial metacentric height, which
may be obtained in practice, when assessing compliance with the criteria given in 3.1.1 and 3.1.2,
respectively. In this connection, a value higher than four persons per square metre is not
necessary.
3.1.2 In addition, the angle of heel on account of turning shall not exceed 10 when calculated
using the following formula:
v 02
d
* * KG
M R = 0.200 *
2
LWL
where:
MR = heeling moment (kNm)
vo
= service speed (m/s)
LWL = length of ship at waterline (m)
= displacement (t)
= mean draught (m)
KG = height of centre of gravity above baseline (m).
MSC 85/26/Add.1
ANNEX 2
Page 19
3.2
Oil tankers of 5,000 dwt and above
Oil tankers, as defined in section 2 (Definitions) of the Introduction, shall comply with regulation 27
of Annex I to MARPOL 73/78.
3.3
Cargo ships carrying timber deck cargoes shall comply with the requirements of 2.2 and 2.3
unless the Administration is satisfied with the application of alternative provision 3.3.2.
3.3.1
Scope
The provisions given hereunder apply to all ships of 24 m in length and over engaged in the
carriage of timber deck cargoes. Ships that are provided with, and make use of, their timber load
line shall also comply with the requirements of regulations 41 to 45 of the 1966 Load Line
Convention.
3.3.2
Alternative stability criteria
For ships loaded with timber deck cargoes and provided that the cargo extends longitudinally
between superstructures (where there is no limiting superstructure at the after end, the timber
deck cargo shall extend at least to the after end of the aftermost hatchway)9 transversely for the
full beam of ship, after due allowance for a rounded gunwale, not exceeding 4% of the breadth of
the ship and/or securing the supporting uprights and which remains securely fixed at large angles
of heel may be:
3.3.2.1 The area under the righting lever curve (GZ curve) shall not be less
than 0.08 metre-radians up to = 40 or the angle of flooding if this angle is less than 40.
3.3.2.2 The maximum value of the righting lever (GZ) shall be at least 0.25 m.
3.3.2.3 At all times during a voyage, the metacentric height GM0 shall not be less
than 0.1 m, taking into account the absorption of water by the deck cargo and/or ice accretion on
the exposed surfaces (details regarding ice accretion are given in part B, chapter 6
(Icing considerations)).
3.3.2.4 When determining the ability of the ship to withstand the combined effects of beam
wind and rolling according to 2.3, the 16 limiting angle of heel under action of steady wind shall
be complied with, but the additional criterion of 80% of the angle of deck edge immersion may
be ignored.
3.4
Cargo ships carrying grain in bulk
The intact stability of ships engaged in the carriage of grain shall comply with the requirements
of the International Code for the Safe Carriage of Grain in Bulk adopted by
resolution MSC.23(59).10
9
10
Refer to regulation 44(2) of the International Convention on Load Lines, 1966 or the Protocol of 1988 relating
thereto, as amended, as applicable.
Refer to part C of chapter VI of the 1974 SOLAS Convention as amended by resolution MSC.23(59).
MSC 85/26/Add.1
ANNEX 2
Page 20
3.5
High-speed craft
High-speed craft, as defined in section 2 (Definitions) of the Introduction, constructed on or

after 1 January 1996 but before 1 July 2002, to which chapter X of the 1974 SOLAS Convention
applies, shall comply with stability requirements of the 1994 HSC Code (resolution MSC.36(63)).
Any high-speed craft to which chapter X of the 1974 SOLAS Convention applies, irrespective of
its date of construction, which has undergone repairs, alterations or modifications of a major
character; and a high-speed craft constructed on or after 1 July 2002, shall comply with stability
requirements of the 2000 HSC Code (resolution MSC.97(73)).
MSC 85/26/Add.1
ANNEX 2
Page 21
PART B
RECOMMENDATIONS FOR CERTAIN TYPES OF SHIPS
AND ADDITIONAL GUIDELINES
CHAPTER 1
1.1
GENERAL
Purpose
The purpose of this part of the Code is to:
1.2
.1
recommend stability criteria and other measures for ensuring the safe operation of
certain types of ships to minimize the risk to such ships, to the personnel on board
and to the environment; and
.2
provide guidelines for stability information, operational provisions against

capsizing, icing considerations, considerations for watertight integrity and the
determination of lightship parameters.
Application
1.2.1 This part of the Code contains recommended intact stability criteria for certain types of
ships and other marine vehicles not included in part A or intended to supplement those of part A
in particular cases regarding size or operation.
1.2.2 Administrations may impose additional requirements regarding the design aspects of
ships of novel design or ships not otherwise covered by the Code.
1.2.3 The criteria stated in this part should give guidance to Administrations if no national
requirements are applied.
MSC 85/26/Add.1
ANNEX 2
Page 22
CHAPTER 2
RECOMMENDED DESIGN CRITERIA FOR CERTAIN TYPES OF

SHIPS
2.1
Fishing vessels
2.1.1
Scope
The provisions given hereunder apply to decked seagoing fishing vessels as defined in section 2
(Definitions) of the Introduction. The stability criteria given in 2.1.3 and 2.1.4 below should be
complied with for all conditions of loading as specified in 3.4.1.6, unless the Administration is
satisfied that operating experience justifies departures therefrom.
2.1.2
Apart from general precautions referred to in part B, 5.1, 5.2 and 5.3, the following measures
should be considered as preliminary guidance on matters influencing safety as related to stability:
.1
all fishing gear and other heavy material should be properly stowed and placed as
low in the vessel as possible;
.2
particular care should be taken when pull from fishing gear might have a negative
effect on stability, e.g., when nets are hauled by power-block or the trawl catches
obstructions on the sea-bed. The pull of the fishing gear should be from as low a
point on the vessel, above the waterline, as possible;
.3
gear for releasing the deck load in fishing vessels which carry the catch on deck,
e.g., herring, should be kept in good working condition;
.4
when the main deck is prepared for carrying deck load by dividing it with pound
boards, there should be slots between them of suitable size to allow easy flow of
water to freeing ports, thus preventing trapping of water;
.5
to prevent a shift of the fish load carried in bulk, portable divisions in the holds
should be properly installed;
.6
reliance on automatic steering may be dangerous as this prevents changes to

course which may be needed in bad weather;
.7
necessary care should be taken to maintain adequate freeboard in all loading

conditions, and where load line regulations are applicable they should be strictly
adhered to at all times; and
.8
particular care should be taken when the pull from fishing gear results in
dangerous heel angles. This may occur when fishing gear fastens onto an
underwater obstacle or when handling fishing gear, particularly on purse seiners,
or when one of the trawl wires tears off. The heel angles caused by the fishing
gear in these situations may be eliminated by employing devices which can relieve
or remove excessive forces applied through the fishing gear. Such devices should
not impose a danger to the vessel through operating in circumstances other than
those for which they were intended.
MSC 85/26/Add.1
ANNEX 2
Page 23
2.1.3
Recommended general criteria11
2.1.3.1 The general intact stability criteria given in part A, 2.2.1 to 2.2.3 should apply to fishing
vessels having a length of 24 m and over, with the exception of requirements on the initial
metacentric height GM (part A, 2.2.4), which, for fishing vessels, should not be less than 0.35 m
for single-deck vessels. In vessels with complete superstructure or vessels of 70 m in length and
over the metacentric height may be reduced to the satisfaction of the Administration but in no
case should be less than 0.15 m.
2.1.3.2 The adoption by individual countries of simplified criteria which apply such basic
stability values to their own types and classes of vessels is recognized as a practical and valuable
method of economically judging the stability.
2.1.3.3 Where arrangements other than bilge keels are provided to limit the angle of roll, the
Administration should be satisfied that the stability criteria referred to in 2.1.3.1 are maintained
in all operating conditions.
2.1.4
Severe wind and rolling criterion (weather criterion) for fishing vessels
2.1.4.1 The Administration may apply the provisions of part A, 2.3 to fishing vessels of 45 m
length and over.
2.1.4.2 For fishing vessels in the length range between 24 m and 45 m, the Administration may
apply the provisions of part A, 2.3. Alternatively the values of wind pressure (see part A, 2.3.2)
may be taken from the following table:
h (m)
P (Pa)
1
316
2
386
3
429
4
460
5
485
6 and over
504
where h is the vertical distance from the centre of the projected vertical area of the vessel above
the waterline, to the waterline.
2.1.5
Recommendation for an interim simplified stability criterion for decked fishing vessels
under 30 m in length
2.1.5.1 For decked vessels with a length less than 30 m, the following approximate formula for
the minimum metacentric height GMmin (in metres) for all operating conditions should be used as
the criterion:
2
l
f
B
f
GM min = 0.53 + 2 B 0.075 0.37 + 0.82 0.014 0.032 S
B
B
D
L
where:
11
is the length of the vessel on the waterline in maximum load condition (m)
ls
is the actual length of enclosed superstructure extending from side to side

of the vessel (m)
Refer to regulation III/2 of the 1993 Torremolinos Protocol.
MSC 85/26/Add.1
ANNEX 2
Page 24
B
is the extreme breadth of the vessel on the waterline in maximum load

condition (m)
is the depth of the vessel measured vertically amidships from the base line
to the top of the upper deck at side (m)
is the smallest freeboard measured vertically from the top of the upper
deck at side to the actual waterline (m).
The formula is applicable for vessels having:

.1
f/B between 0.02 and 0.2;
.2
ls/L smaller than 0.6;
.3
B/D between 1.75 and 2.15;
.4
sheer fore and aft at least equal to or exceeding the standard sheer prescribed in
regulation 38(8) of the International Convention on Load Lines, 1966 or the
Protocol of 1988 as amended, as applicable; and
.5
height of superstructure included in the calculation is not less than 1.8 m.
For ships with parameters outside the above limits the formula should be applied with special
care.
2.1.5.2 The above formula is not intended as a replacement for the basic criteria given
in 2.1.3 and 2.1.4 but is to be used only if circumstances are such that cross curves of stability,
KM curve and subsequent GZ curves are not and cannot be made available for judging a
particular vessels stability.
2.1.5.3 The calculated value of GM, should be compared with actual GM values of the vessel in
all loading conditions. If an inclining experiment based on estimated displacement, or another
approximate method of determining the actual GM is used, a safety margin should be added to
the calculated GMmin.
2.2
Pontoons
2.2.1
Application
The provisions given hereunder apply to seagoing pontoons. A pontoon is considered to be

normally:
.1
non self-propelled;
.2
unmanned;
.3
carrying only deck cargo;
.4
having a block coefficient of 0.9 or greater;
MSC 85/26/Add.1
ANNEX 2
Page 25
2.2.2
.5
having a breadth/depth ratio of greater than 3; and
.6
having no hatchways in the deck except small manholes closed with gasketed covers.
Stability drawings and calculations
The following information is typical of that required to be submitted to the Administration for
approval:
2.2.3
.1
lines drawing;
.2
hydrostatic curves;
.3
cross curves of stability;
.4
report of draught and density readings and calculation of lightship displacement

and longitudinal centre of gravity;
.5
statement of justification of assumed vertical centre of gravity; and
.6
simplified stability guidance such as a loading diagram, so that the pontoon may
be loaded in compliance with the stability criteria.
Concerning the performance of calculations
The following guidance is suggested:

.1
no account should be taken of the buoyancy of deck cargo (except buoyancy

credit for adequately secured timber);
.2
consideration should be given to such factors as water absorption (e.g., timber),

trapped water in cargo (e.g., pipes) and ice accretion;
.3
in performing wind heel calculations:

.3.1
the wind pressure should be constant and for general operations be

considered to act on a solid mass extending over the length of the cargo
deck and to an assumed height above the deck;
.3.2
the centre of gravity of the cargo should be assumed at a point mid-height

of the cargo; and
.3.3
the wind lever should be taken from the centre of the deck cargo to a point
at one half the mean draught;
.4
calculations should be performed covering the full range of operating draughts; and
.5
the down-flooding angle should be taken as the angle at which an opening through
which progressive flooding may take place is immersed. This would not be an
opening closed by a watertight manhole cover or a vent fitted with an automatic
closure.
MSC 85/26/Add.1
ANNEX 2
Page 26
2.2.4
Intact stability criteria
2.2.4.1 The area under the righting lever curve up to the angle of maximum righting lever
should not be less than 0.08 metre-radians.
2.2.4.2 The static angle of heel due to a uniformly distributed wind load of 540 Pa
(wind speed 30 m/s) should not exceed an angle corresponding to half the freeboard for the
relevant loading condition, where the lever of wind heeling moment is measured from the
centroid of the windage area to half the draught.
2.2.4.3 The minimum range of stability should be:
for L 100 m:
20;
for L 150 m:
15;
for intermediate length:
by interpolation.
2.3
Containerships greater than 100 m
2.3.1
Application12
These requirements apply to containerships greater than 100 m in length as defined in section 2
(Definitions) of the Introduction. They may also be applied to other cargo ships in this length
range with considerable flare or large water plane areas. The Administration may apply the
following criteria instead of those in part A, 2.2.
2.3.2
Intact stability
2.3.2.1 The area under the righting lever curve (GZ curve) should not be less
than 0.009/C metre-radians up to = 30 angle of heel, and not less than 0.016/C metre-radians
up to = 40 or the angle of flooding f (as defined in part A, 2.2) if this angle is less than 40.
2.3.2.2 Additionally, the area under the righting lever curve (GZ curve) between the angles of
heel of 30 and 40 or between 30 and f, if this angle is less than 40, should not be less
than 0.006/C metre-radians.
2.3.2.3 The righting lever GZ should be at least 0.033/C m at an angle of heel equal or greater
than 30.
2.3.2.4 The maximum righting lever GZ should be at least 0.042/C m.
2.3.2.5 The total area under the righting lever curve (GZ curve) up to the angle of flooding f
should not be less than 0.029/C metre-radians.
12
Since the criteria in this section were empirically developed with the data of containerships less than 200 m
in length, they should be applied to ships beyond such limits with special care.
MSC 85/26/Add.1
ANNEX 2
Page 27
2.3.2.6 In the above criteria the form factor C should be calculated using the formula and
figure 2.3-1:
d D'
C= 2
Bm
d
KG
CB
CW
100
L
where:
d
= mean draught (m)
D'
= moulded depth of the ship, corrected for defined parts of volumes

within the hatch coamings according to the formula:
2 b BD
D' = D + h
BD
2 lH

, as defined in figure 2.3-1;
L
= moulded depth of the ship (m);
BD = moulded breadth of the ship (m);

KG = height of the centre of mass above base, corrected for free surface
effect, not be taken as less than d (m);
CB = block coefficient;
CW = water plane coefficient;
lH
= length of each hatch coaming within L/4 forward and aft from
amidships (m) (see figure 2.3-1);
= mean width of hatch coamings within L/4 forward and aft from
= mean height of hatch coamings within L/4 forward and aft from
= length of the ship (m);
= breadth of the ship on the waterline (m);
Bm = breadth of the ship on the waterline at half mean draught (m).
MSC 85/26/Add.1
ANNEX 2
Page 28
Figure 2.3-1
The shaded areas in figure 2.3-1 represent partial volumes within the hatch coamings considered
contributing to resistance against capsizing at large heeling angles when the ship is on a wave crest.
2.3.2.7 The use of electronic loading and stability instrument is encouraged in determining the
ships trim and stability during different operational conditions.
2.4
Offshore supply vessels
2.4.1
Application
2.4.1.1 The provisions given hereunder apply to offshore supply vessels, as defined in section 2
(Definitions) of the Introduction, of 24 m in length and over. The alternative stability criteria
contained in 2.4.5 apply to vessels of not more than 100 m in length.
2.4.1.2 For a vessel engaged in near-coastal voyages, as defined in section Definitions, the
principles given in 2.4.2 should guide the Administration in the development of its national
standards. Relaxations from the requirements of the Code may be permitted by an
Administration for vessels engaged in near-coastal voyages off its own coasts provided the
operating conditions are, in the opinion of that Administration, such as to render compliance with
the provisions of the Code unreasonable or unnecessary.
2.4.1.3 Where a ship other than an offshore supply vessel, as defined in section Definitions, is
employed on a similar service, the Administration should determine the extent to which
compliance with the provisions of the Code is required.
2.4.2
Principles governing near-coastal voyages
2.4.2.1 The Administration defining near-coastal voyages for the purpose of the present Code
should not impose design and construction standards for a vessel entitled to fly the flag of
another State and engaged in such voyages in a manner resulting in a more stringent standard for
MSC 85/26/Add.1
ANNEX 2
Page 29
such a vessel than for a vessel entitled to fly its own flag. In no case should the Administration
impose, in respect of a vessel entitled to fly the flag of another State, standards in excess of the
Code for a vessel not engaged in near-coastal voyages.
2.4.2.2 With respect to a vessel regularly engaged in near-coastal voyages off the coast of
another State the Administration should prescribe design and construction standards for such a
vessel at least equal to those prescribed by the Government of the State off whose coast the
vessel is engaged, provided such standards do not exceed the Code in respect of a vessel not
engaged in near-coastal voyages.
2.4.2.3 A vessel which extends its voyages beyond a near-coastal voyage should comply with
the present Code.
2.4.3
Constructional precautions against capsizing
2.4.3.1 Access to the machinery space should, if possible, be arranged within the forecastle.
Any access to the machinery space from the exposed cargo deck should be provided with two
weathertight closures. Access to spaces below the exposed cargo deck should preferably be from
a position within or above the superstructure deck.
2.4.3.2 The area of freeing ports in the side bulwarks of the cargo deck should at least meet the
requirements of regulation 24 of the International Convention on Load Lines, 1966 or the
Protocol of 1988 relating thereto, as amended, as applicable. The disposition of the freeing ports
should be carefully considered to ensure the most effective drainage of water trapped in pipe
deck cargoes or in recesses at the after end of the forecastle. In vessels operating in areas where
icing is likely to occur, no shutters should be fitted in the freeing ports.
2.4.3.3 The Administration should give special attention to adequate drainage of pipe stowage
positions having regard to the individual characteristics of the vessel. However, the area
provided for drainage of the pipe stowage positions should be in excess of the required freeing
port area in the cargo deck bulwarks and should not be fitted with shutters.
2.4.3.4 A vessel engaged in towing operations should be provided with means for quick release
of the towing hawser.
2.4.4
Operational procedures against capsizing
2.4.4.1 The arrangement of cargo stowed on deck should be such as to avoid any obstruction of
the freeing ports or of the areas necessary for the drainage of pipe stowage positions to the
freeing ports.
2.4.4.2 A minimum freeboard at the stern of at least 0.005 L should be maintained in all
operating conditions.
2.4.5
Stability criteria
2.4.5.1 The stability criteria given in part A, 2.2 should apply to all offshore supply vessels
except those having characteristics which render compliance with part A, 2.2 impracticable.
2.4.5.2 The following equivalent criteria should be applied where a vessels characteristics
render compliance with part A, 2.2 impracticable:
MSC 85/26/Add.1
ANNEX 2
Page 30
.1
the area under the curve of righting levers (GZ curve) should not be less
than 0.07 metre-radians up to an angle of 15 when the maximum righting lever
(GZ) occurs at 15 and 0.055 metre-radians up to an angle of 30 when the
maximum righting lever (GZ) occurs at 30 or above. Where the maximum
righting lever (GZ) occurs at angles of between 15 and 30, the corresponding
area under the righting lever curve should be:
0.055 + 0.001 (30 - max) metre-radians13;
.2
the area under the righting lever curve (GZ curve) between the angles of heel
of 30 and 40, or between 30 and f if this angle is less than 40, should be not
less than 0.03 metre-radians;
.3
the righting lever (GZ) should be at least 0.2 m at an angle of heel equal to or
greater than 30;
.4
the maximum righting lever (GZ) should occur at an angle of heel not less than 15;
.5
the initial transverse metacentric height (GMo) should not be less than 0.15 m; and
.6
reference is made also to part A, 2.1.3 to 2.1.5 and part B, 5.1.
2.5
Special purpose ships
2.5.1
Application
The provisions given hereunder apply to special purpose ships, as defined in section 2
(Definitions) of the Introduction, of not less than 500 gross tonnage. The Administration may
also apply these provisions as far as reasonable and practicable to special purpose ships of less
than 500 gross tonnage.
2.5.2
Stability criteria
The intact stability of special purpose ships should comply with the provisions given in
part A, 2.2 except that the alternative criteria given in part B, 2.4.5 which apply to offshore
supply vessels may be used for special purpose ships of less than 100 m in length of similar
design and characteristics.
2.6
Mobile offshore drilling units (MODUs)
2.6.1
Application
2.6.1.1 The provisions given hereunder apply to mobile offshore drilling units as defined in
section 2 (Definitions) of the Introduction, the keels of which are laid or which are at a similar
stage of construction on or after 1 May 1991. For MODUs constructed before that date, the
corresponding provisions of chapter 3 of resolution A.414(XI) should apply.
13
max is the angle of heel in degrees at which the righting lever curve reaches its maximum.
MSC 85/26/Add.1
ANNEX 2
Page 31
2.6.1.2 The coastal State may permit any unit designed to a lesser standard than that of this
chapter to engage in operations, having taken account of the local environmental conditions.
Any such unit should, however, comply with safety requirements which in the opinion of the
coastal State are adequate for the intended operation and ensure the overall safety of the unit and
the personnel on board.
2.6.2
Righting moment and wind heeling moment curves
2.6.2.1 Curves of righting moments and of wind heeling moments similar to figure 2.6-1 with
supporting calculations should be prepared covering the full range of operating draughts,
including those in transit conditions, taking into account the maximum deck cargo and equipment
in the most unfavourable position applicable. The righting moment curves and wind heeling
moment curves should be related to the most critical axes. Account should be taken of the free
surface of liquids in tanks.
Figure 2.6-1 Righting moment and wind heeling moment curves
2.6.2.2 Where equipment is of such a nature that it can be lowered and stowed, additional wind
heeling moment curves may be required and such data should clearly indicate the position of
such equipment.
2.6.2.3 The curves of wind heeling moment should be drawn for wind forces calculated by the
following formula:
F = 0.5 * CS * CH * * V2 * A
where:
is the wind force (N)
CS
is the shape coefficient depending on the shape of the structural

member exposed to the wind (see table 2.6.2.3-1)
CH
is the height coefficient depending on the height above sea level of

the structural member exposed to wind (see table 2.6.2.3-2)
is the air mass density (1.222 kg/m)
MSC 85/26/Add.1
ANNEX 2
Page 32
V
is the wind velocity (m/s)
is the projected area of all exposed surfaces in either the upright or

the heeled condition (m).
Table 2.6.2.3-1 Values of the coefficient CS
Shape
Spherical
Cylindrical
Large flat surface (hull, deck-house, smooth under-deck areas)
Drilling derrick
Wires
Exposed beams and girders under deck
Small parts
Isolated shapes (crane, beam, etc.)
Clustered deck-houses or similar structures
CS
0.40
0.50
1.00
1.25
1.20
1.30
1.40
1.50
1.10
Table 2.6.2.3-2 Values of the coefficient CH

Height above sea level (m)
0 15.3
15.3 30.5
30.5 46
46.0 61
61.0 76
76.0 91.5
91.5 106.5
106.5 122
122.0 137
137.0 152.5
152.5 167.5
167.5 183
183.0 198
198.0 213.5
213.5 228.5
228.5 244
244.0 256
Above 256
CH
1
1.1
1.2
1.3
1.37
1.43
1.48
1.52
1.56
1.6
1.63
1.67
1.7
1.72
1.75
1.77
1.79
1.8
2.6.2.4 Wind forces should be considered from any direction relative to the unit and the value of
the wind velocity should be as follows:
.1
in general, a minimum wind velocity of 36 m/s (70 knots) for offshore service
should be used for normal operating conditions and a minimum wind velocity
of 51.5 m/s (100 knots) should be used for the severe storm conditions; and
.2
where a unit is to be limited in operation to sheltered locations (protected inland

waters such as lakes, bays, swamps, rivers, etc.), consideration should be given to
a reduced wind velocity of not less than 25.8 m/s (50 knots) for normal operating
conditions.
MSC 85/26/Add.1
ANNEX 2
Page 33
2.6.2.5 In calculating the projected areas to the vertical plane, the area of surfaces exposed to
wind due to heel or trim, such as under decks, etc., should be included, using the appropriate
shape factor. Open truss work may be approximated by taking 30% of the projected block area
of both the front and back section, i.e. 60% of the projected area of one side.
2.6.2.6 In calculating the wind heeling moments, the lever of the wind overturning force should
be taken vertically from the centre of pressure of all surfaces exposed to the wind to the centre of
lateral resistance of the underwater body of the unit. The unit is to be assumed floating free of
mooring restraint.
2.6.2.7 The wind heeling moment curve should be calculated for a sufficient number of heel
angles to define the curve. For ship-shaped hulls the curve may be assumed to vary as the cosine
function of ship heel.
2.6.2.8 Wind heeling moments derived from wind-tunnel tests on a representative model of the
unit may be considered as alternatives to the method given in 2.6.2.3 to 2.6.2.7. Such heeling
moment determination should include lift and drag effects at various applicable heel angles.
2.6.3
2.6.3.1 The stability of a unit in each mode of operation should meet the following criteria
(see also figure 2.6-2):
.1
for surface and self-elevating units the area under the righting moment curve to
the second intercept or down-flooding angle, whichever is less, should be not less
than 40% in excess of the area under the wind heeling moment curve to the same
limiting angle;
.2
for column-stabilized units the area under the righting moment curve to the angle
of down-flooding should be not less than 30% in excess of the area under the wind
heeling moment curve to the same limiting angle; and
.3
the righting moment curve should be positive over the entire range of angles from
upright to the second intercept.
Figure 2.6-2 Righting moment and heeling moment curves
MSC 85/26/Add.1
ANNEX 2
Page 34
2.6.3.2 Each unit should be capable of attaining a severe storm condition in a period of time
consistent with the meteorological conditions. The procedures recommended and the
approximate length of time required, considering both operating conditions and transit
conditions, should be contained in the operating manual, as referred to in 3.6.2. It should be
possible to achieve the severe storm condition without the removal or relocation of solid
consumables or other variable load. However, the Administration may permit loading a unit past
the point at which solid consumables would have to be removed or relocated to go to severe storm
condition under the following conditions, provided the allowable KG requirement is not exceeded:
.1
in a geographic location where weather conditions annually or seasonally do not

become sufficiently severe to require a unit to go to severe storm condition; or
.2
where a unit is required to support extra deckload for a short period of time that is
well within the bounds of a favourable weather forecast.
The geographic locations and weather conditions and loading conditions when this is permitted
should be identified in the operating manual.
2.6.3.3 Alternative stability criteria may be considered by the Administration provided an
equivalent level of safety is maintained and if they are demonstrated to afford adequate positive
initial stability. In determining the acceptability of such criteria, the Administration should
consider at least the following and take into account as appropriate:
.1
environmental conditions representing realistic winds (including gusts) and waves

appropriate for world-wide service in various modes of operation;
.2
dynamic response of a unit. Analysis should include the results of wind-tunnel

tests, wave tank model tests, and non-linear simulation, where appropriate.
Any wind and wave spectra used should cover sufficient frequency ranges to
ensure that critical motion responses are obtained;
.3
potential for flooding taking into account dynamic responses in a seaway;
.4
susceptibility to capsizing considering the units restoration energy and the static
inclination due to the mean wind speed and the maximum dynamic response; and
.5
an adequate safety margin to account for uncertainties.
An example of alternative criteria for twin-pontoon column-stabilized semi-submersible units is

given in section 2.6.4.
2.6.4
An example of alternative intact stability criteria for twin-pontoon column-stabilized

semi-submersible units
2.6.4.1 The criteria given below apply only to twin-pontoon column-stabilized semi-submersible
units in severe storm conditions which fall within the following ranges of parameters:
Vp/Vt
is between 0.48 and 0.58
Awp/(Vc)2/3
Lwp/[Vc * (Lptn/2)]
The parameters used in the above equations are defined in paragraph 2.6.4.3.
MSC 85/26/Add.1
ANNEX 2
Page 35
2.6.4.2
The stability of a unit in the survival mode of operation should meet the following criteria.
2.6.4.2.1
Capsize criteria
These criteria are based on the wind heeling moment and righting moment curves calculated as
shown in section 2.6.2 of the Code at the survival draught. The reserve energy area B should
be equal to or greater than 10% of the dynamic response area A as shown in figure 2.6-3.
Area B/Area A 0.10
where:
Area A is the area under the righting moment curve measured from
1 to (1 + 1.15 * dyn)
Area B is the area under the righting moment curve measured from
(1 + 1.15 * dyn) to 2
1
is the first intercept with the 100 knot wind moment curve
is the second intercept with the 100 knot wind moment curve
dyn
is the dynamic response angle due to waves and fluctuating wind
dyn
= (10.3 + 17.8 * C)/(1 + GM/(1.46 + 0.28 * BM))
= (Lptn5/3 * VCPw1 * Aw* Vp * Vc1/3)/( Lwp5/3 * Vt)
Parameters used in the above equations are defined in paragraph 2.6.4.3.
Figure 2.6-3 Righting moment and heeling moment curves
MSC 85/26/Add.1
ANNEX 2
Page 36
2.6.4.2.2
Down-flooding criteria
These criteria are based on the physical dimensions of the unit and the relative motion of the unit
about a static inclination due to a 75 knot wind measured at the survival draught. The initial
down-flooding distance (DFD0) should be greater than the reduction in down-flooding distance at
the survival draught as shown in figure 2.6-4.
DFD0 - RDFD > 0.0
where:
DFD0
is the initial down-flooding distance to Dm (m)
RDFD
is the reduction in
SF (k * QSD1 + RMW)
down-flooding
distance
(m)
to
SF
is equal to 1.1, which is a safety factor to account for

uncertainties in the analysis, such as non-linear effects
(correlation
factor)
is
equal
0.55 + 0.08 * (a - 4) + 0.056 * (1.52 - GM);
(GM cannot be taken to be greater than 2.44 m)
a
to
is equal to (FBD0/Dm)*(Sptn * Lcc)/Awp

(a cannot be taken to be less than 4)
QSD1
is equal to DFD0 minus quasi-static down-flooding distance

at 1 (m), but not to be taken less than 3 m
RMW
is the relative motion due to waves about 1 (m),

equal to 9.3 + 0.11 * (X - 12.19)
X
is equal to Dm *(Vt/Vp)*(Awp2/Iwp)*(Lccc/Lptn)
(X cannot be taken to be less than 12.19 m).
Figure 2.6-4 Definition of down-flooding distance and relative motion
The parameters used in the above equations are defined in paragraph 2.6.4.3.
equal
MSC 85/26/Add.1
ANNEX 2
Page 37
2.6.4.3
Geometric parameters
Awp
is the waterplane area at the survival draught, including the effects of bracing
members as applicable (m).
Aw
is the effective wind area with the unit in the upright position (i.e. the product of
projected area, shape coefficient and height coefficient) (m2).
BM
is the vertical distance from the metacentre to the centre of buoyancy with the unit
in the upright position (m).
Dm
is the initial survival draught (m).
FBD0 is the vertical distance from Dm, to the top of the upper exposed weathertight deck
at the side (m).
GM
for paragraph 2.6.4.2.1, GM is the metacentric height measured about the roll or
diagonal axis, whichever gives the minimum reserve energy ratio, B/A. This
axis is usually the diagonal axis as it possesses a characteristically larger projected
wind area which influences the three characteristic angles mentioned above (m).
GM
for paragraph 2.6.4.2.2, GM is the metacentric height measured about the axis
which gives the minimum down-flooding distance margin (i.e. generally the
direction that gives the largest QSD1) (m).
Iwp
is the water plane second moment of inertia at the survival draught, including the
effects of bracing members as applicable (m4).
Lccc
is the longitudinal distance between centres of the corner columns (m).
Lptn
is the length of each pontoon (m).
Sptn
is the transverse distance between the centrelines of the pontoons (m).
Vc
is the total volume of all columns from the top of the pontoons to the top of the
column structure, except for any volume included in the upper deck (m3).
Vp
is the total combined volume of both pontoons (m3).
Vt
is the total volume of the structures (pontoons, columns and bracings) contributing
to the buoyancy of the unit, from its baseline to the top of the column structure,
except for any volume included in the upper deck (m3).
VCPw1 is the vertical centre of wind pressure above Dm (m).
MSC 85/26/Add.1
ANNEX 2
Page 38
2.6.4.4
Capsize criteria assessment form

Input data
GM
............................................................................... = .......... m
BM
............................................................................... = .......... m
VCPw1
............................................................................... = .......... m
Aw
............................................................................... = .......... m2
Vt
............................................................................... = .......... m3
Vc
............................................................................... = .......... m
Vp
............................................................................... = .......... m
Iwp
............................................................................... = .......... m4
Lptn
............................................................................... = .......... m
Determine
1
............................................................................... = .......... deg
............................................................................... = .......... deg
(Lptn5/3 * VCPw1 * Aw * Vp * Vc1/3)/(Iwp5/3 * Vt) ... = .......... m-1
dyn
(10.3 + 17.8C)/(1 + GM/(1.46 + 0.28BM)) ......... = .......... deg
Area A
............................................................................... = .......... m-deg
Area B
............................................................................... = .......... m-deg
Results
Reserve energy ratio:

B/A = ..............................
GM
= .......................... m
(minimum = 0.1)
(KG = ............ m)
Note: The minimum GM is that which produces a B/A ratio = 0.1
MSC 85/26/Add.1
ANNEX 2
Page 39
2.6.4.5
Down-flooding criteria assessment form

Input data
DFD0
............................................................................... = .............. m
FBD0
............................................................................... = .............. m
GM
............................................................................... = .............. m
Dm
............................................................................... = .............. m
Vt
............................................................................... = .............. m
Vp
............................................................................... = .............. m
Awp
............................................................................... = .............. m
Iwp
............................................................................... = .............. m4
Lccc
............................................................................... = .............. m
Lptn
............................................................................... = .............. m
Sptn
............................................................................... = .............. m
SF
............................................................................... = 1.1
Determine
1
..................................................................... = .... deg
DFD1
..................................................................... = .... m
QSD1 = DFD0 DFD1 ............................................. = .... m

a
= (FBD0/Dm)*(Sptn * Lccc)/Awp ...................... = .... (amin = 4)
= 0.55 + 0.08*(a - 4) + 0.056*(1.52 - GM) ..... = .... m (GMmax = 2.44 m)
= Dm*(Vt/Vp)*(Awp /Iwp) )(Lccc/Lptn) .............. = .... m (Xmin = 12.19 m)
RMW = 9.3 + 0.11*(X - 12.19) ............................... = .... m

RDFD = SF*(k * QSD1 + RMW) ............................. = .... m
Results
Down-flooding margin:
DFD0 - RDFD
= ...................... (minimum = 0.0 m)
GM
= .............. m
(KG = .............. m)
Note: The minimum GM is that which produces a down-flooding margin = 0.0 m.

MSC 85/26/Add.1
ANNEX 2
Page 40
CHAPTER 3
3.1
GUIDANCE IN PREPARING STABILITY INFORMATION
Effect of free surfaces of liquids in tanks
3.1.1 For all loading conditions, the initial metacentric height and the righting lever curve
should be corrected for the effect of free surfaces of liquids in tanks.
3.1.2 Free surface effects should be considered whenever the filling level in a tank is less
than 98% of full condition. Free surface effects need not be considered where a tank is
nominally full, i.e. filling level is 98% or above. Free surface effects for small tanks may be
ignored under condition specified in 3.1.12.14
But nominally full cargo tanks should be corrected for free surface effects at 98% filling level.
In doing so, the correction to initial metacentric height should be based on the inertia moment of
liquid surface at 5 of heeling angle divided by displacement, and the correction to righting lever
is suggested to be on the basis of real shifting moment of cargo liquids.
3.1.3 Tanks which are taken into consideration when determining the free surface correction
may be in one of two categories:
.1
tanks with filling levels fixed (e.g., liquid cargo, water ballast). The free surface
correction should be defined for the actual filling level to be used in each tank; or
.2
tanks with filling levels variable (e.g., consumable liquids such as fuel oil, diesel
oil and fresh water, and also liquid cargo and water ballast during liquid transfer
operations). Except as permitted in 3.1.5 and 3.1.6, the free surface correction
should be the maximum value attainable between the filling limits envisaged for
each tank, consistent with any operating instructions.
3.1.4 In calculating the free surface effects in tanks containing consumable liquids, it should be
assumed that for each type of liquid at least one transverse pair or a single centreline tank has a
free surface and the tank or combination of tanks taken into account should be those where the
effect of free surfaces is the greatest.
3.1.5 Where water ballast tanks, including anti-rolling tanks and anti-heeling tanks, are to be
filled or discharged during the course of a voyage, the free surface effects should be calculated to
take account of the most onerous transitory stage relating to such operations.
3.1.6 For ships engaged in liquid transfer operations, the free surface corrections at any stage15
of the liquid transfer operations may be determined in accordance with the filling level in each
tank at that stage of the transfer operation.
3.1.7 The corrections to the initial metacentric height and to the righting lever curve should be
addressed separately as follows.
14
15
Refer to the intact stability design criteria, contained in MARPOL regulation I/27, together with the associated
Unified Interpretation 45.
A sufficient number of loading conditions representing the initial, intermediate and final stages of the filling or
discharge operation using the free surface correction at the filling level in each tank at the considered stage may
be evaluated to fulfil this recommendation.
MSC 85/26/Add.1
ANNEX 2
Page 41
3.1.8 In determining the correction to initial metacentric height, the transverse moments of
inertia of the tanks should be calculated at 0 angle of heel according to the categories indicated
in 3.1.3.
3.1.9 The righting lever curve may be corrected by any of the following methods subject to the
agreement of the Administration:
.1
correction based on the actual moment of fluid transfer for each angle of heel
calculated; or
.2
correction based on the moment of inertia, calculated at 0 angle of heel, modified

at each angle of heel calculated.
3.1.10 Corrections may be calculated according to the categories indicated in 3.1.2.

3.1.11 Whichever method is selected for correcting the righting lever curve, only that method
should be presented in the ships stability booklet. However, where an alternative method is
described for use in manually calculated loading conditions, an explanation of the differences
which may be found in the results, as well as an example correction for each alternative, should
be included.
3.1.12 Small tanks which satisfy the following condition corresponding to an angle of
inclination of 30, need not be included in the correction:
Mfs / min< 0.01 m
where:
Mfs
free surface moment (mt)
min
is the minimum ship displacement calculated at dmin (t)
dmin
is the minimum mean service draught of the ship without cargo,

with 10% stores and minimum water ballast, if required (m).
3.1.13 The usual remainder of liquids in empty tanks need not be taken into account in
calculating the corrections, provided that the total of such residual liquids does not constitute a
significant free surface effect.
3.2
Permanent ballast
If used, permanent ballast should be located in accordance with a plan approved by the
Administration and in a manner that prevents shifting of position. Permanent ballast should not
be removed from the ship or relocated within the ship without the approval of the Administration.
Permanent ballast particulars should be noted in the ships stability booklet.
MSC 85/26/Add.1
ANNEX 2
Page 42
Assessment of compliance with stability criteria16
3.3
3.3.1 Except as otherwise required by this Code, for the purpose of assessing in general
whether the stability criteria are met, stability curves using the assumptions given in this Code
should be drawn for the loading conditions intended by the owner in respect of the ships operations.
3.3.2 If the owner of the ship does not supply sufficiently detailed information regarding such
loading conditions, calculations should be made for the standard loading conditions.
3.4
Standard conditions of loading to be examined
3.4.1
Loading conditions
The standard loading conditions referred to in the text of the present Code are as follows.
3.4.1.1 For a passenger ship:
.1
ship in the fully loaded departure condition with cargo, full stores and fuel and
with the full number of passengers with their luggage;
.2
ship in the fully loaded arrival condition, with cargo, the full number of
passengers and their luggage but with only 10% stores and fuel remaining;
.3
ship without cargo, but with full stores and fuel and the full number of passengers
and their luggage; and
.4
ship in the same condition as at 0 above with only 10% stores and fuel remaining.
3.4.1.2 For a cargo ship:

.1
ship in the fully loaded departure condition, with cargo homogeneously

distributed throughout all cargo spaces and with full stores and fuel;
.2
ship in the fully loaded arrival condition with cargo homogeneously distributed
throughout all cargo spaces and with 10% stores and fuel remaining;
.3
ship in ballast in the departure condition, without cargo but with full stores and
fuel; and
.4
ship in ballast in the arrival condition, without cargo and with 10% stores and fuel
remaining.
3.4.1.3 For a cargo ship intended to carry deck cargoes:

.1
16
ship in the fully loaded departure condition with cargo homogeneously distributed
in the holds and with cargo specified in extension and mass on deck, with full
stores and fuel; and
Care should be taken in the assessment of compliance with stability criteria, especially conditions in which
liquid transfer operations might be expected or anticipated, to insure that the stability criteria is met at all stages
of the voyage.
MSC 85/26/Add.1
ANNEX 2
Page 43
.2
ship in the fully loaded arrival condition with cargo homogeneously distributed in
holds and with a cargo specified in extension and mass on deck, with 10% stores
and fuel.
3.4.1.4 For a ship intended to carry timber deck cargoes:

The loading conditions which should be considered for ships carrying timber deck cargoes are
specified in 3.4.1.3. The stowage of timber deck cargoes should comply with the provisions of
chapter 3 of the Code of Safe Practice for Ships Carrying Timber Deck Cargoes, 1991
(resolution A.715(17)).17
3.4.1.5 For an offshore supply vessel the standard loading conditions should be as follows:
.1
vessel in fully loaded departure condition with cargo distributed below deck and
with cargo specified by position and weight on deck, with full stores and fuel,
corresponding to the worst service condition in which all the relevant stability
criteria are met;
.2
vessel in fully loaded arrival condition with cargo as specified in 3.4.1.5.1, but
with 10% stores and fuel;
.3
vessel in ballast departure condition, without cargo but with full stores and fuel;
.4
vessel in ballast arrival condition, without cargo and with 10% stores and fuel
remaining; and
.5
vessel in the worst anticipated operating condition.
3.4.1.6 For fishing vessels the standard loading conditions referred to in 2.1.1 are as follows18:
3.4.2
.1
departure conditions for the fishing grounds with full fuel, stores, ice, fishing gear,
etc.;
.2
departure from the fishing grounds with full catch and a percentage of stores, fuel,
etc., as agreed by the Administration;
.3
arrival at home port with 10% stores, fuel, etc. remaining and full catch; and
.4
arrival at home port with 10% stores, fuel, etc. and a minimum catch, which
should normally be 20% of full catch but may be up to 40% provided the
Administration is satisfied that operating patterns justify such a value.
Assumptions for calculating loading conditions
3.4.2.1 For the fully loaded conditions mentioned in 3.4.1.2.1, 3.4.1.2.2, 3.4.1.3.1 and 3.4.1.3.2
if a dry cargo ship has tanks for liquid cargo, the effective deadweight in the loading conditions
therein described should be distributed according to two assumptions, i.e. with cargo tanks full,
and with cargo tanks empty.
17
18
Refer to chapter VI of the 1974 SOLAS Convention and to part C of chapter VI of the 1974 SOLAS
Convention as amended by resolution MSC.22(59).
MSC 85/26/Add.1
ANNEX 2
Page 44
3.4.2.2 In the conditions mentioned in 3.4.1.1.1, 3.4.1.2.1 and 3.4.1.3.1 it should be assumed
that the ship is loaded to its subdivision load line or summer load line or if intended to carry a
timber deck cargo, to the summer timber load line with water ballast tanks empty.
3.4.2.3 If in any loading condition water ballast is necessary, additional diagrams should be
calculated taking into account the water ballast. Its quantity and disposition should be stated.
3.4.2.4 In all cases, the cargo in holds is assumed to be fully homogeneous unless this condition
is inconsistent with the practical service of the ship.
3.4.2.5 In all cases, when deck cargo is carried, a realistic stowage mass should be assumed and
stated, including the height of the cargo.
3.4.2.6 Considering timber deck cargo the following assumptions are to be made for calculating
the loading conditions referred to in 3.4.1.4:
.1
the amount of cargo and ballast should correspond to the worst service condition
in which all the relevant stability criteria of part A 2.2 or the optional criteria
given in part A 3.3.2, are met. In the arrival condition, it should be assumed that
the weight of the deck cargo has increased by 10% owing to water absorption.
3.4.2.7 For offshore supply vessels, the assumptions for calculating loading conditions
should be as follows:
.1
if a vessel is fitted with cargo tanks, the fully loaded conditions of 3.4.1.5.1
and 3.4.1.5.2 should be modified, assuming first the cargo tanks full and then the
cargo tanks empty;
.2
if in any loading condition water ballast is necessary, additional diagrams should

be calculated, taking into account the water ballast, the quantity and disposition of
which should be stated in the stability information;
.3
in all cases when deck cargo is carried a realistic stowage weight should be
assumed and stated in the stability information, including the height of the cargo
and its centre of gravity;
.4
where pipes are carried on deck, a quantity of trapped water equal to a certain
percentage of the net volume of the pipe deck cargo should be assumed in and
around the pipes. The net volume should be taken as the internal volume of the
pipes, plus the volume between the pipes. This percentage should be 30 if the
freeboard amidships is equal to or less than 0.015 L and 10 if the freeboard
amidships is equal to or greater than 0.03 L. For intermediate values of the
freeboard amidships the percentage may be obtained by linear interpolation.
In assessing the quantity of trapped water, the Administration may take into
account positive or negative sheer aft, actual trim and area of operation; or
.5
if a vessel operates in zones where ice accretion is likely to occur, allowance

for icing should be made in accordance with the provisions of chapter 6
(Icing considerations).
MSC 85/26/Add.1
ANNEX 2
Page 45
3.4.2.8 For fishing vessels the assumptions for calculating loading conditions should be as
follows:
.1
allowance should be made for the weight of the wet fishing nets and tackle, etc.,
on deck;
.2
allowance for icing, where this is anticipated to occur, should be made in

accordance with the provisions of 6.3;
.3
in all cases the cargo should be assumed to be homogeneous unless this is

inconsistent with practice;
.4
in conditions referred to in 3.4.1.6.2 and 3.4.1.6.3 deck cargo should be included

if such a practice is anticipated;
.5
water ballast should normally only be included if carried in tanks which are
specially provided for this purpose.
3.5
Calculation of stability curves
3.5.1
General
Hydrostatic and stability curves should be prepared for the trim range of operating loading
conditions taking into account the change in trim due to heel (free trim hydrostatic calculation).
The calculations should take into account the volume to the upper surface of the deck sheathing.
Furthermore, appendages and sea chests need to be considered when calculating hydrostatics and
cross curves of stability. In the presence of port-starboard asymmetry, the most unfavourable
righting lever curve should be used.
3.5.2
Superstructures, deckhouses, etc., which may be taken into account
3.5.2.1 Enclosed superstructures complying with regulation 3(10)(b) of the 1966 Load Line
Convention and the Protocol of 1988 relating thereto, as amended, may be taken into account.
3.5.2.2 Additional tiers of similarly enclosed superstructures may also be taken into account.
As guidance windows (pane and frame) that are considered without deadlights in additional tiers
above the second tier if considered buoyant should be designed with strength to sustain a safety
margin19 with regard to the required strength of the surrounding structure.20
3.5.2.3 Deckhouses on the freeboard deck may be taken into account, provided that they
comply with the conditions for enclosed superstructures laid down in regulation 3(10)(b) of
the 1966 Load Line Convention and the Protocol of 1988 relating thereto, as amended.
3.5.2.4 Where deckhouses comply with the above conditions, except that no additional exit is
provided to a deck above, such deckhouses should not be taken into account; however, any deck
openings inside such deckhouses should be considered as closed even where no means of closure
are provided.
19
20
As a guidance for Administrations a safety margin of 30% should be applied.

IMO guidance for testing these windows is to be developed.
MSC 85/26/Add.1
ANNEX 2
Page 46
3.5.2.5 Deckhouses, the doors of which do not comply with the requirements of regulation 12
of the 1966 Load Line Convention and the Protocol of 1988 relating thereto, as amended, should
not be taken into account; however, any deck openings inside the deckhouse are regarded as
closed where their means of closure comply with the requirements of regulations 15, 17 or 18
of the 1966 Load Line Convention and the Protocol of 1988 relating thereto, as amended.
3.5.2.6 Deckhouses on decks above the freeboard deck should not be taken into account, but
openings within them may be regarded as closed.
3.5.2.7 Superstructures and deckhouses not regarded as enclosed can, however, be taken into
account in stability calculations up to the angle at which their openings are flooded (at this angle,
the static stability curve should show one or more steps, and in subsequent computations the
flooded space should be considered non-existent).
3.5.2.8 In cases where the ship would sink due to flooding through any openings, the stability
curve should be cut short at the corresponding angle of flooding and the ship should be
considered to have entirely lost its stability.
3.5.2.9 Small openings such as those for passing wires or chains, tackle and anchors, and also
holes of scuppers, discharge and sanitary pipes should not be considered as open if they
submerge at an angle of inclination more than 30. If they submerge at an angle of 30 or less,
these openings should be assumed open if the Administration considers this to be a source of
significant flooding.
3.5.2.10 Trunks may be taken into account. Hatchways may also be taken into account having
regard to the effectiveness of their closures.
3.5.3
Calculation of stability curves for ships carrying timber deck cargoes
In addition to the provisions given above, the Administration may allow account to be taken of
the buoyancy of the deck cargo assuming that such cargo has a permeability of 25% of the
volume occupied by the cargo. Additional curves of stability may be required if the
Administration considers it necessary to investigate the influence of different permeabilities
and/or assumed effective height of the deck cargo.
3.6
Stability booklet
3.6.1 Stability data and associated plans should be drawn up in the working language of the ship
and any other language the Administration may require. Reference is also made to the International
Safety Management (ISM) Code, adopted by the Organization by resolution A.741(18). All
translations of the stability booklet should be approved.
3.6.2 Each ship should be provided with a stability booklet, approved by the Administration,
which contains sufficient information to enable the master to operate the ship in compliance with
the applicable requirements contained in the Code. The Administration may have additional
requirements. On a mobile offshore drilling unit, the stability booklet may be referred to as an
operating manual. The stability booklet may include information on longitudinal strength. This
Code addresses only the stability-related contents of the booklet.21
21
Refer to regulation II-1/22 of the 1974 SOLAS Convention, as amended, regulation 10 of the International
Convention on Load Lines, 1966 or the Protocol of 1988 as amended, as applicable and regulation III/10 of
the 1993 Torremolinos Protocol.
MSC 85/26/Add.1
ANNEX 2
Page 47
3.6.3 For ships carrying timber deck cargoes:
.1
comprehensive stability information should be supplied which takes into account

timber deck cargo. Such information should enable the master, rapidly and
simply, to obtain accurate guidance as to the stability of the ship under varying
conditions of service. Comprehensive rolling period tables or diagrams have
proved to be very useful aids in verifying the actual stability conditions;22
.2
the Administration may deem it necessary that the master be given information
setting out the changes in deck cargo from that shown in the loading conditions,
when the permeability of the deck cargo is significantly different from 25% (refer
to 3.5.3); and
.3
conditions should be shown indicating the maximum permissible amount of deck

cargo having regard to the lightest stowage rate likely to be met in service.
3.6.4 The format of the stability booklet and the information included will vary dependent on
the ship type and operation. In developing the stability booklet, consideration should be given to
including the following information23:
22
23
.1
a general description of the ship;
.2
instructions on the use of the booklet;
.3
general arrangement plans showing watertight compartments, closures, vents,

downflooding angles, permanent ballast, allowable deck loadings and freeboard
diagrams;
.4
hydrostatic curves or tables and cross curves of stability calculated on a

free-trimming basis, for the ranges of displacement and trim anticipated in normal
operating conditions;
.5
capacity plan or tables showing capacities and centres of gravity for each cargo
stowage space;
.6
tank sounding tables showing capacities, centres of gravity, and free surface data
for each tank;
.7
information on loading restrictions, such as maximum KG or minimum GM curve or

table that can be used to determine compliance with the applicable stability criteria;
.8
standard operating conditions and examples for developing other acceptable

loading conditions using the information contained in the stability booklet;
.9
a brief description of the stability calculations done including assumptions;
.10
general precautions for preventing unintentional flooding;
.11
information concerning the use of any special cross-flooding fittings with

descriptions of damage conditions which may require cross-flooding;
Refer to regulation II-1/22 of the 1974 SOLAS Convention, as amended, and regulation 10(2) of the
International Convention on Load Lines, 1966 or the Protocol of 1988 relating thereto, as amended, as applicable.
Refer to the Model Loading and Stability Manual (MSC/Circ.920).
MSC 85/26/Add.1
ANNEX 2
Page 48
.12
any other necessary guidance for the safe operation of the ship under normal and
emergency conditions;
.13
a table of contents and index for each booklet;
.14
inclining test report for the ship, or:

.14.1 where the stability data is based on a sister ship, the inclining test report of
that sister ship along with the lightship measurement report for the ship in
question; or
.14.2 where lightship particulars are determined by other methods than from
inclining of the ship or its sister, a summary of the method used to
determine those particulars;
.15
recommendation for determination of ships stability by means of an in-service

inclining test.
3.6.5 As an alternative to the stability booklet mentioned in 3.6.1, a simplified booklet in an

approved form containing sufficient information to enable the master to operate the ship in
compliance with the applicable provisions of the Code as may be provided at the discretion of the
Administration concerned.
3.7
Operational measures for ships carrying timber deck cargoes
3.7.1 The stability of the ship at all times, including during the process of loading and
unloading timber deck cargo, should be positive and to a standard acceptable to the
Administration. It should be calculated having regard to:
.1
the increased weight of the timber deck cargo due to:

.1.1
absorption of water in dried or seasoned timber, and
.1.2
ice accretion, if applicable (chapter 6 (Icing considerations));
.2
variations in consumables;
.3
the free surface effect of liquid in tanks; and
.4
weight of water trapped in broken spaces within the timber deck cargo and
especially logs.
3.7.2 The master should:

.1
cease all loading operations if a list develops for which there is no satisfactory
explanation and it would be imprudent to continue loading;
.2
before proceeding to sea, ensure that:

.2.1
the ship is upright;
.2.2
the ship has an adequate metacentric height; and
.2.3
the ship meets the required stability criteria.
MSC 85/26/Add.1
ANNEX 2
Page 49
3.7.3 The masters of ships having a length less than 100 m should also:
.1
exercise good judgement to ensure that a ship which carries stowed logs on deck
has sufficient additional buoyancy so as to avoid overloading and loss of stability
at sea;
.2
be aware that the calculated GM0 in the departure condition may decrease
continuously owing to water absorption by the deck cargo of logs, consumption of
fuel, water and stores and ensure that the ship has adequate GM0 throughout the
voyage; and
.3
be aware that ballasting after departure may cause the ships operating draught to
exceed the timber load line. Ballasting and deballasting should be carried out in
accordance with the guidance provided in the Code of Safe Practice for Ships
Carrying Timber Deck Cargoes, 1991 (resolution A.715(17)).
3.7.4 Ships carrying timber deck cargoes should operate, as far as possible, with a safe margin
of stability and with a metacentric height which is consistent with safety requirements but such
metacentric height should not be allowed to fall below the recommended minimum, as specified
in part A, 3.3.2.
3.7.5 However, excessive initial stability should be avoided as it will result in rapid and violent
motion in heavy seas which will impose large sliding and racking forces on the cargo causing
high stresses on the lashings. Operational experience indicates that metacentric height should
preferably not exceed 3% of the breadth in order to prevent excessive accelerations in rolling
provided that the relevant stability criteria given in part A, 3.3.2 are satisfied. This recommendation
may not apply to all ships and the master should take into consideration the stability information
obtained from the ships stability booklet.
3.8
Operating booklets for certain ships
3.8.1 Special purpose ships and novel craft, should be provided with additional information in
the stability booklet such as design limitations, maximum speed, worst intended weather
conditions or other information regarding the handling of the craft that the master needs to
operate the ship safely.
3.8.2 For double hull oil tankers of single cargo tank across design, an operation manual for
loading and unloading cargo oil should be provided, including operational procedures of loading
and unloading cargo oil and detailed data of the initial metacentric height of the oil tanker and
that of free surface correction of liquids in cargo oil tanks and ballast tanks during loading and
unloading cargo oil (including ballasting and discharging) and cargo oil washing of tanks.24
3.8.3 The stability booklet of ro-ro passenger ships should contain information concerning the
importance of securing and maintaining all closures watertight due to the rapid loss of stability
which may result when water enters the vehicle deck and the fact that capsize can rapidly follow.
24
Refer to the Guidance on intact stability of existing tankers during liquid transfer operations
(MSC/Circ.706-MEPC/Circ.304).
MSC 85/26/Add.1
ANNEX 2
Page 50
CHAPTER 4
STABILITY CALCULATIONS PERFORMED BY STABILITY

INSTRUMENTS
Stability instruments25
4.1
A stability instrument installed onboard should cover all stability requirements applicable to the
ship. The software is subject to approval by the Administration. Active and passive systems are
defined in 4.1.2. These requirements cover passive systems and the off-line operation mode of
active systems only.
4.1.1
General
4.1.1.1 The scope of stability calculation software should be in accordance with the approved
stability booklet and should at least include all information and perform all calculations or checks
as necessary to ensure compliance with the applicable stability requirements.
4.1.1.2 An approved stability instrument is not a substitute for the approved stability booklet,
and is used as a supplement to the approved stability booklet to facilitate stability calculations.
4.1.1.3 The input/output information should be easily comparable with the approved stability
booklet so as to avoid confusion and possible misinterpretation by the operator.
4.1.1.4 An operation manual should be provided for the stability instrument.
4.1.1.5 The language in which the stability calculation results are displayed and printed out as
well as the operation manual is written should be the same as used in the ships approved
stability booklet. A translation into a language considered appropriate may be required.
4.1.1.6 The stability instrument is ship specific equipment and the results of the calculations are
only applicable to the ship for which it has been approved.
4.1.1.7 In case of modifications of the ship which cause alterations in the stability booklet, the
specific approval of any original stability calculation software is no longer valid. The software
should be modified accordingly and re-approved.
4.1.1.8 Any change in software version related to the stability calculation should be reported to
and be approved by the Administration.
4.1.2
Data entry system
4.1.2.1 A passive system requires manual data entry.

4.1.2.2 An active system replaces partly the manual entry with sensors reading and entering the
contents of tanks, etc.
4.1.2.3 Any integrated system which controls or initiates actions based on the sensor-supplied
inputs is not within the scope of this Code except the part calculating the stability.
25
Refer to the Guidelines for the approval of stability instruments (MSC.1/Circ.1229).
MSC 85/26/Add.1
ANNEX 2
Page 51
4.1.3
Types of stability software
Three types of calculations performed by stability software are acceptable depending upon
a vessels stability requirements:
Type 1
Software calculating intact stability only (for vessels not required to meet a damage
stability criterion).
Type 2
Software calculating intact stability and checking damage stability on basis of a limit
curve (e.g., for vessels applicable to SOLAS part B-1 damage stability calculations, etc.)
or previously approved loading conditions.
Type 3
Software calculating intact stability and damage stability by direct application of
pre-programmed damage cases for each loading condition (for some tankers, etc.). The
results of the direct calculations performed by the stability instrument could be accepted
by the Administration even if they differ from the required minimum GM or maximum
VCG stated in the approved stability booklet.
Such deviations could be accepted under the condition that all relevant stability requirements will
be complied with by the results of the direct calculations.
4.1.4
Functional requirements
4.1.4.1 The stability instrument should present relevant parameters of each loading condition in
order to assist the master in his judgement on whether the ship is loaded within the approved
limits. The following parameters should be presented for a given loading condition:
.1
detailed deadweight data items including centre of gravity and free surfaces,
if applicable;
.2
trim, list;
.3
draught at the draught marks and perpendiculars;
.4
summary of loading condition displacement, VCG, LCG, TCG, VCB, LCB, TCB,
LCF, GM and GML;
.5
table showing the righting lever versus heeling angle including trim and draught;
.6
down-flooding angle and corresponding down-flooding opening; and
.7
compliance with stability criteria: Listings of all calculated stability criteria, the
limit values, the obtained values and the conclusions (criteria fulfilled or not
fulfilled).
MSC 85/26/Add.1
ANNEX 2
Page 52
4.1.4.2 If direct damage stability calculations are performed, the relevant damage cases according
to the applicable rules should be pre-defined for automatic check of a given loading condition.
4.1.4.3 A clear warning should be given on screen and in hard copy printout if any of the
limitations are not complied with.
4.1.4.4 The data should be presented on screen and in hard copy printout in a clear
unambiguous manner.
4.1.4.5 The date and time of a saved calculation should be part of the screen display and hard
copy printout.
4.1.4.6 Each hard copy printout should contain identification of the calculation program
including version number.
4.1.4.7 Units of measurement should be clearly identified and used consistently within a loading
calculation.
4.1.5
Acceptable tolerances
Depending on the type and scope of programs, the acceptable tolerances should be determined
differently, according to 4.1.5.1 or 4.1.5.2. Deviation from these tolerances should not be
accepted unless the Administration considers that there is a satisfactory explanation for the
difference and that there will be no adverse effect on the safety of the ship.
The accuracy of the results should be determined using an independent program or the approved
stability booklet with identical input.
4.1.5.1 Programs which use only pre-programmed data from the approved stability booklet as
the basis for stability calculations should have zero tolerances for the printouts of input data.
Output data tolerances should be close to zero, however, small differences associated with
calculation rounding or abridged input data are acceptable. Additionally differences associated
with the use of hydrostatic and stability data for trims and the method calculating free surface
moments that differ from those in the approved stability booklet are acceptable subject to review
by the Administration.
4.1.5.2 Programs which use hull form models as their basis for stability calculations should
have tolerances for the printouts of basic calculated data established against either data from the
approved stability booklet or data obtained using the Administrations approval model.
4.1.6
Approval procedure
4.1.6.1 Conditions of approval of the stability instrument

The software approval includes:
.1
verification of type approval, if any;
.2
verification that the data used is consistent with the current condition of the ship
(refer to 4.1.6.2);
MSC 85/26/Add.1
ANNEX 2
Page 53
.3
verification and approval of the test conditions; and
.4
verification that the software is appropriate for the type of ship and stability
calculations required.
The satisfactory operation of the stability instrument is to be verified by testing upon installation
(refer to 4.1.8). A copy of the approved test conditions and the operation manual for the stability
instrument are to be available on board.
4.1.6.2 Specific approval
4.1.6.2.1 The accuracy of the computational results and actual ship data used by the calculation
program for the particular ship on which the program will be installed should be to the
satisfaction of the Administration.
4.1.6.2.2 Upon application for data verification, minimum of four loading conditions should be
taken from the ships approved stability booklet, which should be used as the test conditions. For
ships carrying liquids in bulk, at least one of the conditions should include partially filled tanks.
For ships carrying grain in bulk, one of the grain loading conditions should include a partially
filled grain compartment. Within the test conditions each compartment should be loaded at least
once. The test conditions normally should cover the range of load draughts from the deepest
envisaged loaded condition to the light ballast condition and should include at least one departure
and one arrival condition.
4.1.6.2.3 The following data, submitted by the applicant, should be consistent with
arrangements and most recently approved lightship characteristics of the ship according to
current plans and documentation on file, subject to possible further verification on board:
.1
identification of the calculation program including version number.

Main dimensions, hydrostatic particulars and, if applicable, the ships profile;
.2
the position of the forward and aft perpendiculars, and if appropriate, the
calculation method to derive the forward and aft draughts at the actual position of
the ships draught marks;
.3
ships lightweight and centre of gravity derived from the most recently approved
inclining experiment or light weight survey;
.4
lines plan, offset tables or other suitable presentation of hull form data including
all relevant appendages, if necessary to model the ship;
.5
compartment definitions, including frame spacing, and centres of volume,

together with capacity tables (sounding/ullage tables), free surface corrections,
if appropriate; and
.6
cargo and consumables distribution for each loading condition.
Verification by the Administration does not absolve the shipowner of responsibility for ensuring
that the information programmed into the stability instrument is consistent with the current
condition of the ship and approved stability booklet.
MSC 85/26/Add.1
ANNEX 2
Page 54
4.1.7
User manual
A simple and straightforward user manual written in the same language as the stability booklet
should be provided, containing descriptions and instructions, as appropriate, for at least the following:
.1
installation;
.2
function keys;
.3
menu displays;
.4
input and output data;
.5
required minimum hardware to operate the software;
.6
use of the test loading conditions;
.7
computer-guided dialogue steps; and
.8
list of warnings.
A user manual in electronic format may be provided in addition to the written manual.
4.1.8
Installation testing
4.1.8.1 To ensure correct working of the stability instrument after the final or updated software
has been installed, it is the responsibility of the ships master to have test calculations carried out
according to the following pattern in the presence of an Administrations surveyor. From the
approved test conditions at least one load case (other than light ship) should be calculated.
Note: Actual loading condition results are not suitable for checking the correct working of the
stability instrument.
4.1.8.2 Normally, the test conditions are permanently stored in the stability instrument. Steps to
be performed:
.1
retrieve the test load case and start a calculation run; compare the stability results
with those in the documentation;
.2
change several items of deadweight (tank weights and the cargo weight)
sufficiently to change the draught or displacement by at least 10%. The results
should be reviewed to ensure that they differ in a logical way from those of the
approved test condition;
.3
revise the above modified load condition to restore the initial test condition and
compare the results. The relevant input and output data of the approved test
condition should be replicated; and
.4
alternatively, one or more test conditions should be selected and the test
calculations performed by entering all deadweight data for each selected test
condition into the program as if it were a proposed loading. The results should be
verified as identical to the results in the approved copy of the test conditions.
MSC 85/26/Add.1
ANNEX 2
Page 55
4.1.9
Periodical testing
4.1.9.1 It is the responsibility of the ships master to check the accuracy of the stability
instrument at each annual survey by applying at least one approved test condition. If an
Administrations representative is not present for the stability instrument check, a copy of the test
condition results obtained by this check should be retained on board as documentation of
satisfactory testing for the Administrations representatives verification.
4.1.9.2 At each renewal survey this checking for all approved test loading conditions should be
done in the presence of the Administrations representative.
4.1.9.3 The testing procedure should be carried out in accordance with paragraph 4.1.8.
4.1.10 Other requirements
4.1.10.1 Protection against unintentional or unauthorized modification of programs and data

should be provided.
4.1.10.2 The program should monitor operation and activate an alarm when the program is
incorrectly or abnormally used.
4.1.10.3 The program and any data stored in the system should be protected from corruption
by loss of power.
4.1.10.4 Error messages with regard to limitations such as filling a compartment beyond
capacity or more than once, or exceeding the assigned load line, etc., should be included.
4.1.10.5 If any software related to stability measures such as sea keeping abilities of the vessel,
evaluation of in-service inclining experiments and processing the results for further calculation,
as well as the evaluation of roll period measurements is installed on board, such software should
be reported to the Administration for consideration.
4.1.10.6 Program functionalities should include mass and moment calculations with numerical
and graphical presentation of the results, such as initial stability values, righting lever curve,
areas under the righting lever curve and range of stability.
4.1.10.7 All input data from automatically measuring sensors, such as gauging devices or
draught reading systems should be presented to the user for verification. The user should have
the possibility to override faulty readings manually.
MSC 85/26/Add.1
ANNEX 2
Page 56
CHAPTER 5
5.1
OPERATIONAL PROVISIONS AGAINST CAPSIZING
5.1.1 Compliance with the stability criteria does not ensure immunity against capsizing,
regardless of the circumstances, or absolve the master from his responsibilities. Masters should
therefore exercise prudence and good seamanship having regard to the season of the year,
weather forecasts and the navigational zone and should take the appropriate action as to speed
and course warranted by the prevailing circumstances.26
5.1.2 Care should be taken that the cargo allocated to the ship is capable of being stowed so
that compliance with the criteria can be achieved. If necessary, the amount should be limited to
the extent that ballast weight may be required.
5.1.3 Before a voyage commences, care should be taken to ensure that the cargo, cargo
handling cranes and sizeable pieces of equipment have been properly stowed or lashed so as to
minimize the possibility of both longitudinal and lateral shifting, while at sea, under the effect of
acceleration caused by rolling and pitching.27
5.1.4 A ship, when engaged in towing operations, should possess an adequate reserve of
stability to withstand the anticipated heeling moment arising from the tow line without
endangering the towing ship. Deck cargo on board the towing ship should be so positioned as
not to endanger the safe working of the crew on deck or impede the proper functioning of the
towing equipment and be properly secured. Tow line arrangements should include towing
springs and a method of quick release of the tow.
5.1.5 The number of partially filled or slack tanks should be kept to a minimum because of
their adverse effect on stability. The negative effect on stability of filled pool tanks should be
taken into consideration.
5.1.6 The stability criteria contained in part A chapter 2 set minimum values, but no maximum
values are recommended. It is advisable to avoid excessive values of metacentric height, since
these might lead to acceleration forces which could be prejudicial to the ship, its complement, its
equipment and to safe carriage of the cargo. Slack tanks may, in exceptional cases, be used as a
means of reducing excessive values of metacentric height. In such cases, due consideration
should be given to sloshing effects.
5.1.7 Regard should be paid to the possible adverse effects on stability where certain bulk
cargoes are carried. In this connection, attention should be paid to the IMO Code of Safe
Practice for Solid Bulk Cargoes.
5.2
Operational precautions in heavy weather
5.2.1 All doorways and other openings, through which water can enter into the hull or
deckhouses, forecastle, etc., should be suitably closed in adverse weather conditions and
accordingly all appliances for this purpose should be maintained on board and in good condition.
26
27
Refer to the Revised Guidance to the master for avoiding dangerous situations in adverse weather and sea
conditions (MSC.1/Circ.1228).
Refer to the Guidelines for the preparation of the Cargo Securing Manual (MSC/Circ.745).
MSC 85/26/Add.1
ANNEX 2
Page 57
5.2.2 Weathertight and watertight hatches, doors, etc., should be kept closed during navigation,
except when necessarily opened for the working of the ship and should always be ready for
immediate closure and be clearly marked to indicate that these fittings are to be kept closed
except for access. Hatch covers and flush deck scuttles in fishing vessels should be kept properly
secured when not in use during fishing operations. All portable deadlights should be maintained
in good condition and securely closed in bad weather.
5.2.3 Any closing devices provided for vent pipes to fuel tanks should be secured in bad
weather.
5.2.4 Fish should never be carried in bulk without first being sure that the portable divisions in
the holds are properly installed.
5.3
Ship handling in heavy weather
5.3.1 In all conditions of loading necessary care should be taken to maintain a seaworthy
freeboard.
5.3.2 In severe weather, the speed of the ship should be reduced if propeller emergence,
shipping of water on deck or heavy slamming occurs.
5.3.3 Special attention should be paid when a ship is sailing in following, quartering or head
seas because dangerous phenomena such as parametric resonance, broaching to, reduction of
stability on the wave crest, and excessive rolling may occur singularly, in sequence or
simultaneously in a multiple combination, creating a threat of capsize. A ships speed and/or
course should be altered appropriately to avoid the above-mentioned phenomena.28
5.3.4 Reliance on automatic steering may be dangerous as this prevents ready changes to
course which may be needed in bad weather.
5.3.5 Water trapping in deck wells should be avoided. If freeing ports are not sufficient for the
drainage of the well, the speed of the ship should be reduced or the course changed, or both.
Freeing ports provided with closing appliances should always be capable of functioning and are
not to be locked.
5.3.6 Masters should be aware that steep or breaking waves may occur in certain areas, or in
certain wind and current combinations (river estuaries, shallow water areas, funnel shaped bays, etc.).
These waves are particularly dangerous, especially for small ships.
5.3.7 In severe weather, the lateral wind pressure may cause a considerable angle of heel.
If anti-heeling measures (e.g., ballasting, use of anti-heeling devices, etc.) are used to compensate
for heeling due to wind, changes of the ships course relative to the wind direction may lead to
dangerous angles of heel or capsizing. Therefore, heeling caused by the wind should not be
compensated with anti-heeling measures, unless, subject to the approval by the Administration,
the vessel has been proven by calculation to have sufficient stability in worst case conditions
(i.e. improper or incorrect use, mechanism failure, unintended course change, etc.). Guidance on
the use of anti-heeling measures should be provided in the stability booklet.
28
Refer to the Revised Guidance to the master for avoiding dangerous situations in adverse weather and sea
conditions (MSC.1/Circ.1228).
MSC 85/26/Add.1
ANNEX 2
Page 58
5.3.8 Use of operational guidelines for avoiding dangerous situations in severe weather
conditions or an on-board computer based system is recommended. The method should be
simple to use.
5.3.9 High-speed craft should not be intentionally operated outside the worst intended
conditions and limitations specified in the relevant certificates, or in documents referred to
therein.
MSC 85/26/Add.1
ANNEX 2
Page 59
CHAPTER 6
6.1
ICING CONSIDERATIONS
General
6.1.1 For any ship operating in areas where ice accretion is likely to occur, adversely affecting
a ships stability, icing allowances should be included in the analysis of conditions of loading.
6.1.2 Administrations are advised to take icing into account and are permitted to apply national
standards where environmental conditions are considered to warrant a higher standard than those
recommended in the following sections.
6.2
6.2.1 The master should establish or verify the stability of his ship for the worst service
condition, having regard to the increased weight of deck cargo due to water absorption and/or ice
accretion and to variations in consumables.29
6.2.2 When timber deck cargoes are carried and it is anticipated that some formation of ice will
take place, an allowance should be made in the arrival condition for the additional weight.
6.3
Fishing vessels
The calculations of loading conditions for fishing vessels (refer to 3.4.2.8) should, where
appropriate, include allowance for ice accretion, in accordance with the following provisions.
6.3.1
Allowance for ice accretion30
For vessels operating in areas where ice accretion is likely to occur, the following icing
allowance should be made in the stability calculations:
.1
30 kg per square metre on exposed weather decks and gangways;
.2
7.5 kg per square metre for projected lateral area of each side of the vessel above
the water plane;
.3
the projected lateral area of discontinuous surfaces of rail, sundry booms, spars
(except masts) and rigging of vessels having no sails and the projected lateral area
of other small objects should be computed by increasing the total projected area of
continuous surfaces by 5% and the static moments of this area by 10%.
Vessels intended for operation in areas where ice is known to occur should be:
29
30
.4
designed to minimize the accretion of ice; and
.5
equipped with such means for removing ice as the Administration may require; for
example, electrical and pneumatic devices, and/or special tools such as axes or
wooden clubs for removing ice from bulwarks, rails and erections.
Refer to regulation 44(10) of the 1966 Load Line Convention and regulation 44(7) of the 1988 Load Line
Protocol as amended.
MSC 85/26/Add.1
ANNEX 2
Page 60
6.3.2
Guidance relating to ice accretion
In the application of the above standards, the following icing areas should apply:
.1
the area north of latitude 65 30 N, between longitude 28 W and the west coast of
Iceland; north of the north coast of Iceland; north of the rhumb line running from
latitude 66 N, longitude 15 W to latitude 73 30 N, longitude 15 E, north of
latitude 73 30 N between longitude 15 E and 35 E, and east of longitude 35 E,
as well as north of latitude 56 N in the Baltic Sea;
.2
the area north of latitude 43 N bounded in the west by the North American coast
and the east by the rhumb line running from latitude 43 N, longitude 48 W to
latitude 63 N, longitude 28 W and thence along longitude 28 W;
.3
all sea areas north of the North American Continent, west of the areas defined
in 6.3.2.1 and 6.3.2.2;
.4
the Bering and Okhotsk Seas and the Tartary Strait during the icing season; and
.5
south of latitude 60 S.
A chart to illustrate the areas is attached at the end of this chapter.

For vessels operating in areas where ice accretion may be expected:
6.3.3
.6
within the areas defined in 6.3.2.1, 6.3.2.3, 6.3.2.4 and 6.3.2.5 known to having
icing conditions significantly different from those described in 6.3.1, ice accretion
requirements of one half to twice the required allowance may be applied; and
.7
within the area defined in 6.3.2.2, where ice accretion in excess of twice the
allowance required by 6.3.1 may be expected, more severe requirements than
those given in 6.3.1 may be applied.
Brief survey of the causes of ice formation and its influence upon the seaworthiness of
the vessel
6.3.3.1 The skipper of a fishing vessel should bear in mind that ice formation is a complicated
process which depends upon meteorological conditions, condition of loading and behaviour of
the vessel in stormy weather as well as on the size and location of superstructures and rigging.
The most common cause of ice formation is the deposit of water droplets on the vessels structure.
These droplets come from spray driven from wave crests and from ship-generated spray.
6.3.3.2 Ice formation may also occur in conditions of snowfall, sea fog (including arctic sea
smoke), a drastic fall in ambient temperature, as well as from the freezing of drops of rain on
impact with the vessels structure.
6.3.3.3 Ice formation may sometimes be caused or accentuated by water shipped on board and
retained on deck.
MSC 85/26/Add.1
ANNEX 2
Page 61
6.3.3.4 Intensive ice formation generally occurs on stem, bulwark and bulwark rail, front walls
of superstructures and deck-houses, hawse holes, anchors, deck gear, forecastle deck and upper
deck, freeing ports, aerials, stays, shrouds, masts and spars.
6.3.3.5 It should be borne in mind that the most dangerous areas as far as ice formation is
concerned are the sub-Arctic regions.
6.3.3.6 The most intensive ice formation takes place when wind and sea come from ahead.
In beam and quartering winds, ice accumulates quicker on the windward side of the vessel, thus
leading to a constant list which is extremely dangerous.
6.3.3.7 Listed below are meteorological conditions causing the most common type of ice
formation due to spraying of a vessel. Examples of the weight of ice formation on a typical
fishing vessel of displacement in the range 100 t to 500 t are also given. For larger vessels the
weight will be correspondingly greater.
6.3.3.8 Slow accumulations of ice take place:
.1
at ambient temperature from -1C to -3C and any wind force;
.2
at ambient temperature -4C and lower and wind force from 0 m/s to 9 m/s; and
.3
under the conditions of precipitation, fog or sea mist followed by a drastic fall of
the ambient temperature.
Under all these conditions the intensity of ice accumulation may not exceed 1.5 t/h.
6.3.3.9 At ambient temperature of -4C to -8C and wind force 10 m/s to 15 m/s, rapid
accumulation of ice takes place. Under these conditions the intensity of ice accumulation can lie
within the range 1.5 t/h to 4 t/h.
6.3.3.10
Very fast accumulation of ice takes place:
.1
at ambient temperature of -4C and lower and wind forces of 16 m/s and over; and
.2
at ambient temperature -9C and lower and wind force 10 m/s to 15 m/s.
Under these conditions the intensity of ice accumulation can exceed 4 t/h.
6.3.3.11 The skipper should bear in mind that ice formation adversely affects the
seaworthiness of the vessel as ice formation leads to:
.1
an increase in the weight of the vessel due to accumulation of ice on the vessels
surfaces which causes the reduction of freeboard and buoyancy;
.2
a rise of the vessels centre of gravity due to the high location of ice on the
vessels structures with corresponding reduction in the level of stability;
.3
an increase of windage area due to ice formation on the upper parts of the vessel
and hence an increase in the heeling moment due to the action of the wind;
MSC 85/26/Add.1
ANNEX 2
Page 62
.4
a change of trim due to uneven distribution of ice along the vessels length;
.5
the development of a constant list due to uneven distribution of ice across the
breadth of the vessel; and
.6
impairment of the manoeuvrability and reduction of the speed of the vessel.
6.3.4 Operational procedures related to ensuring a fishing vessels endurance in conditions of

ice formation are given in annex 2 (Recommendations for skippers of fishing vessels on ensuring
a vessels endurance in conditions of ice formation).
6.4
Offshore supply vessels 24 m to 100 m in length
For vessels operating in areas where ice accretion is likely to occur:

.1
no shutters should be fitted in the freeing ports; and
.2
with regard to operational precautions against capsizing, reference is made to the

recommendations for skippers of fishing vessels on ensuring a vessels endurance
in conditions of ice formation, as given in paragraph 6.3.3 and in annex 2
(Recommendations for skippers of fishing vessels on ensuring a vessels
endurance in conditions of ice formation).
MSC 85/26/Add.1
ANNEX 2
Page 63
CHAPTER 7
7.1
CONSIDERATIONS FOR WATERTIGHT AND WEATHERTIGHT

INTEGRITY
Hatchways
7.1.1 Cargo and other hatchways in ships to which the International Convention on Load
Lines, 1966, applies should comply with regulations 13, 14, 15, 16 and 26(5) of this Convention.
7.1.2 Hatchways in fishing vessels to which the 1993 Torremolinos Protocol applies should
comply with regulations II/5 and II/6 of this Protocol.
7.1.3 In decked fishing vessels of 12 m in length and over but less than 24 m in length
hatchways should comply with the following:
7.1.3.1 All hatchways should be provided with covers and those which may be opened during
fishing operations should normally be arranged near to the vessels centreline.
7.1.3.2 For the purpose of strength calculations it should be assumed that hatchway covers other
than wood are subject to static load of 10 kN/m2 or the weight of cargo intended to be carried on
them, whichever is the greater.
7.1.3.3 Where covers are constructed of mild steel, the maximum stress according to 7.1.3.2
multiplied by 4.25 should not exceed the minimum ultimate strength of the material. Under these
loads the deflections should not be more than 0.0028 times the span.
7.1.3.4 Covers made of materials other than mild steel or wood should be at least of equivalent
strength to those made of mild steel and their construction should be of sufficient stiffness to
ensure weathertightness under the loads specified in 7.1.3.2.
7.1.3.5 Covers should be fitted with clamping devices and gaskets or other equivalent
arrangements sufficient to ensure weathertightness.
7.1.3.6 The use of wooden hatchway covers is generally not recommended in view of the
difficulty of rapidly securing their weathertightness. However, where fitted they should be
capable of being secured weathertight.
7.1.3.7 The finished thickness of wood hatchway covers should include an allowance for
abrasion due to rough handling. In any case, the finished thickness of these covers should be at
least 4 mm for each 100 mm of unsupported span subject to a minimum of 40 mm and the width
of their bearing surfaces should be at least 65 mm.
7.1.3.8 The height above deck of hatchway coamings on exposed parts of the working deck
should be at least 300 mm for vessels of 12 m in length and at least 600 mm for vessels of 24 m
in length. For vessels of intermediate length the minimum height should be obtained by linear
interpolation. The height above deck of hatchway coamings on exposed parts of the
superstructure deck should be at least 300 mm.
7.1.3.9 Where operating experience has shown justification and on approval of the competent
authority the height of hatchway coamings, except those which give direct access to machinery
spaces may be reduced from the height as specified in 7.1.3.8 or the coamings may be omitted
entirely, provided that efficient watertight hatch covers other than wood are fitted. Such hatchways
MSC 85/26/Add.1
ANNEX 2
Page 64
should be kept as small as practicable and the covers should be permanently attached by hinges
or equivalent means and be capable of being rapidly closed or battened down.
7.2
Machinery space openings
7.2.1 In ships to which the International Convention on Load Lines, 1966 or the Protocol
of 1988 relating thereto as amended, as applicable, applies, machinery space openings should
comply with regulation 17.
7.2.2 In fishing vessels to which the 1993 Torremolinos Protocol applies and in new decked
fishing vessels of 12 m in length and over, but less than 24 m in length, the following
requirements of regulation II/7 of this Protocol should be met:
.1
machinery space openings should be framed and enclosed by casings of a strength

equivalent to the adjacent superstructure. External access openings therein should
be fitted with doors complying with the requirements of regulation II/4 of the
Protocol or, in vessels less than 24 m in length, with hatch covers other than wood
complying with the requirements of 7.1.3 of this chapter; and
.2
openings other than access openings should be fitted with covers of equivalent
strength to the unpierced structure, permanently attached thereto and capable of
being closed weathertight.
7.2.3 In offshore supply vessels, access to the machinery space should, if possible, be arranged
within the forecastle. Any access to the machinery space from the exposed cargo deck should be
provided with two weathertight closures. Access to spaces below the exposed cargo deck should
preferably be from a position within or above the superstructure deck.
7.3
Doors
7.3.1 In passenger ships to which the International Convention for the Safety of Life at
Sea, 1974, applies, doors should comply with regulations II-l/13 and 16 of this Convention.
of 1988 relating thereto, as amended, as applicable, applies, doors should comply with
regulation 12 of this Convention.
7.3.3 In fishing vessels to which the 1993 Torremolinos Protocol applies, doors should comply
with regulation II/2 and regulation II/4 of this Protocol.
7.3.4 In decked fishing vessels of 12 m in length and over but less than 24 m in length:
.1
Watertight doors may be of the hinged type and should be capable of being
operated locally from each side of the door. A notice should be attached to the
door on each side stating that the door should be kept closed at sea.
.2
All access openings in bulkheads of enclosed deck erections, through which water
could enter and endanger the vessel, should be fitted with doors permanently attached
to the bulkhead, framed and stiffened so that the whole structure is of equivalent
strength to the unpierced structure, and weathertight when closed, and means
should be provided so that they can be operated from each side of the bulkhead.
MSC 85/26/Add.1
ANNEX 2
Page 65
7.4
.3
The height above deck of sills in those doorways, companionways, deck erections
and machinery casings situated on the working deck and on superstructure decks
which give direct access to parts of that deck exposed to the weather and sea
should be at least equal to the height of hatchway coamings as specified in 7.1.3.8.
.4
Where operating experience has shown justification and on approval of the

competent authority, the height above deck of sills in the doorways specified
in 7.3.4.3 except those giving direct access to machinery spaces, may be reduced
to not less than 150 mm on superstructure decks and not less than 380 mm on the
working deck for vessels 24 m in length, or not less than 150 mm on the working
deck for vessels of 12 m in length. For vessels of intermediate length the
minimum acceptable reduced height for sills in doorways on the working deck
should be obtained by linear interpolation.
Cargo ports and other similar openings
7.4.1 Cargo ports and other similar openings in ships to which the International Convention on
Load Lines, 1966 or the Protocol of 1988 relating thereto, as amended, as applicable, applies
should comply with regulation 21 of this Convention.
7.4.2 Openings through which water can enter the vessel and fish flaps on stern trawlers in
fishing vessels to which the 1993 Torremolinos Protocol applies should comply with
regulation II/3 of this Protocol.
7.4.3 Cargo port and other similar openings in passenger ships to which the International
Convention for the Safety of Life at Sea, 1974 applies should comply with regulations II-1/15, 17
and 22 of this Convention. In addition, such openings in ro-ro passenger ships to which this
Convention applies, should comply with regulation II-1/17-1 of this Convention.
7.4.4 Cargo port and other similar openings in cargo ships to which the International
Convention for the Safety of Life at Sea, 1974 applies should comply with regulation II-1/15-1 of
this Convention.
7.5
Sidescuttles, window scuppers, inlets and discharges
7.5.1 In passenger ships to which the International Convention for the Safety of Life at
Sea, 1974 applies, openings in shell plating below the bulkhead deck should comply with
regulation II-1/15 of this Convention.
Watertight integrity above the bulkhead deck should comply with regulation II-1/17 of this
Convention.
In addition, in ro-ro passenger ships, watertight integrity below the bulkhead deck should comply
with regulation II-1/23 and integrity of the hull and superstructure should comply with
regulation II-1/17-1 of this Convention.
of 1988 relating thereto, as amended, as applicable, applies, scuppers, inlets and discharges
should comply with regulation 22 and sidescuttles should comply with regulation 23 of this
Convention.
MSC 85/26/Add.1
ANNEX 2
Page 66
7.5.3 In fishing vessels to which the 1993 Torremolinos Protocol applies, sidescuttles and
windows should comply with regulation II/12 and inlets and discharges should comply with
regulation II/13 of this Protocol.
7.5.4 In decked fishing vessels of 12 m in length and over but less than 24 m in length,
sidescuttles, windows and other openings and inlets and discharges should comply with the
following:
.1
sidescuttles to spaces below the working deck and to enclosed spaces on the
working deck should be fitted with hinged deadlights capable of being closed
watertight;
.2
sidescuttles should be fitted in a position such that their sills are above a line
drawn parallel to the working deck at side having its lowest point 500 mm above
the deepest operating waterline;
.3
sidescuttles, together with their glasses and deadlights, should be of substantial

construction to the satisfaction of the competent authority;
.4
skylights leading to spaces below the working deck should be of substantial

construction and capable of being closed and secured weathertight, and with
provision for adequate means of closing in the event of damage to the inserts.
Skylights leading to machinery spaces should be avoided as far as practicable;
.5
toughened safety glass or suitable permanently transparent material of equivalent

strength should be fitted in all wheelhouse windows exposed to the weather.
The means of securing windows and the width of the bearing surfaces should be
adequate, having regard to the window material used. Openings leading to spaces
below deck from a wheelhouse whose windows are not provided with the
protection required by 0 should be fitted with a weathertight closing appliance;
.6
deadlights or a suitable number of storm shutters should be provided where there

is no other method of preventing water from entering the hull through a broken
window or sidescuttle;
.7
the competent authority may accept sidescuttles and windows without deadlights
in side or aft bulkheads of deck erections located on or above the working deck if
satisfied that the safety of the vessel will not be impaired;
.8
the number of openings in the sides of the vessel below the working deck should
be the minimum compatible with the design and proper working of the vessel and
such openings should be provided with closing arrangements of adequate strength
to ensure watertightness and the structural integrity of the surrounding structure;
.9
discharges led through the shell either from spaces below the working deck or
from spaces within deck erections should be fitted with efficient and accessible
means for preventing water from passing inboard. Normally each separate
discharge should have an automatic non-return valve with a positive means of
closing it from a readily accessible position. Such a valve is not required if the
competent authority considers that the entry of water into the vessel through the
opening is not likely to lead to dangerous flooding and that the thickness of the
MSC 85/26/Add.1
ANNEX 2
Page 67
pipe is sufficient. The means for operating the valve with a positive means of
closing should be provided with an indicator showing whether the valve is open or
closed. The open inboard end of any discharge system should be above the
deepest operating waterline at an angle of heel satisfactory to the competent
authority;
.10
in machinery spaces main and auxiliary sea inlets and discharges essential for the
operation of machinery should be controlled locally. Controls should be readily
accessible and should be provided with indicators showing whether the valves are
open or closed. Suitable warning devices should be incorporated to indicate
leakage of water into the space; and
.11
fittings attached to the shell and all valves should be of steel, bronze or other
ductile material. All pipes between the shell and valves should be of steel, except
that in vessels constructed of material other than steel, other suitable materials
may be used.
7.5.5 In cargo ships to which the International Convention for the Safety of Life at Sea, 1974
applies, external openings should comply with regulation II-1/15-1 of this Convention.
7.6
Other deck openings
7.6.1 Miscellaneous openings in freeboard and superstructure decks in ships to which the
International Convention on Load Lines, 1966 or the Protocol of 1988 relating thereto, as amended,
as applicable, applies should comply with regulation 18 of this Convention.
7.6.2 In decked fishing vessels of 12 m and over where it is essential for fishing operations,
flush deck scuttles of the screw, bayonet or equivalent type and manholes may be fitted provided
these are capable of being closed watertight and such devices should be permanently attached to
the adjacent structure. Having regard to the size and disposition of the openings and the design
of the closing devices, metal-to-metal closures may be fitted if they are effectively watertight.
Openings other than hatchways, machinery space openings, manholes and flush scuttles in the
working or superstructure deck should be protected by enclosed structures fitted with
weathertight doors or their equivalent. Companionways should be situated as close as practicable
to the centreline of the vessel.31
7.7
Ventilators, air pipes and sounding devices
7.7.1 Ventilators in ships to which the International Convention on Load Lines, 1966 or the
Protocol of 1988 relating thereto, as amended, as applicable, applies should comply with
regulation 19 and air pipes should comply with regulation 20 of this Convention.
7.7.2 Ventilators in fishing vessels to which the 1993 Torremolinos Protocol applies should
comply with regulation II/9 and air pipes should comply with regulation II/10 of this Protocol.
Sounding devices should comply with regulation II/11 of this Protocol.
31
Refer to regulation II/8 of the 1993 Torremolinos Protocol.
MSC 85/26/Add.1
ANNEX 2
Page 68
7.7.3 Ventilators and air pipes in fishing vessels of 12 m in length and over but less than 24 m
in length should comply with the following:
.1
ventilators should have coamings of substantial construction and should

capable of being closed weathertight by devices permanently attached to
ventilator or adjacent structure. Ventilators should be arranged as close to
vessels centreline as possible and, where practicable, should extend through
top of a deck erection or companionway;
be
the
the
the
.2
the coamings of ventilators should be as high as practicable. On the working deck

the height above deck of coamings of ventilators, other than machinery space
ventilators, should be not less than 760 mm and on superstructure decks not less
than 450 mm. When the height of such ventilators may interfere with the working
of the vessel their coaming heights may be reduced to the satisfaction of the
competent authority. The height above deck of machinery space ventilator
openings should be to the satisfaction of the competent authority;
.3
closing appliances need not be fitted to ventilators the coamings of which extend
more than 2.5 m above the working deck or more than 1.0 m above a deck-house
top or superstructure deck;
.4
where air pipes to tanks or other spaces below deck extend above the working or
superstructure decks the exposed parts of the pipes should be of substantial
construction and, as far as is practicable, located close to the vessels centreline
and protected from damage by fishing or lifting gear. Openings of such pipes
should be protected by efficient means of closing, permanently attached to the
pipe or adjacent structure, except that where the competent authority is satisfied
that they are protected against water trapped on deck, these means of closing may
be omitted; and
.5
where air pipes are situated near the side of the vessel their height above deck to
the point where water may have access below should be at least 760 mm on the
working deck and at least 450 mm on the superstructure deck. The competent
authority may accept reduction of the height of an air pipe to avoid interference
with the fishing operations.
7.7.4 In offshore supply vessels air pipes and ventilators should comply with the following:
.1
air pipes and ventilators should be fitted in protected positions in order to avoid
damage by cargo during operations and to minimize the possibility of flooding.
Air pipes on the exposed cargo and forecastle decks should be fitted with
automatic closing devices; and
.2
due regard should be given to the position of machinery space ventilators.

Preferably they should be fitted in a position above the superstructure deck, or
above an equivalent level if no superstructure deck is fitted.
MSC 85/26/Add.1
ANNEX 2
Page 69
7.8
Freeing ports
7.8.1 Where bulwarks on the weather portion of the freeboard or superstructure decks or,
in fishing vessels, the working decks form wells, freeing ports should be arranged along the
length of the bulwark as to ensure that the deck is freed of water most rapidly and effectively.
Lower edges of freeing ports should be as near the deck as practicable.32
of 1988 relating thereto as amended, as applicable, applies, freeing ports should comply with
regulation 24 of this Convention.
7.8.3 In decked fishing vessels of 12 m in length and over, freeing ports should comply with
the following33.
7.8.3.1 The minimum freeing port area A in m, on each side of the vessel for each well on the
working deck, should be determined in relation to the length l and height of bulwark in the well
as follows:
.1
A=K*l
where:
K = 0.07 for vessels of 24 m in length and over
K = 0.035 for vessels of 12 m in length;
for intermediate lengths the value of K should be obtained by linear
interpolation (l need not be taken as greater than 70% of the
vessels length);
.2
where the bulwark is more than 1.2 m in average height, the required area should
be increased by 0.004 m per metre of length of well for each 0.1 m difference in
height; and
.3
where the bulwark is less than 0.9 m in average height, the required area may be
decreased by 0.004 m per metre of length of well for each 0.1 m difference in
height.
7.8.3.2 The freeing port area calculated according to 7.8.3.1 should be increased where the
Administration or competent authority considers that the vessels sheer is not sufficient to ensure
rapid and effective freeing of the deck of water.
7.8.3.3 Subject to the approval of the Administration or competent authority, the minimum
freeing port area for each well on the superstructure deck should be not less than one-half the
area A given in 7.8.3.1 except that where the superstructure deck forms a working deck for
fishing operations the minimum area on each side should be not less than 75% of the area A.
32
33
Refer to regulation 24(5) of the International Convention on Load Lines, 1966 or the Protocol of 1988
as amended, as applicable and regulation 11/14(4) of the 1993 Torremolinos Protocol.
Refer to regulation II/l4 of the 1993 Torremolinos Protocol.
MSC 85/26/Add.1
ANNEX 2
Page 70
7.8.3.4 Freeing ports should be so arranged along the length of bulwarks as to provide the most
rapid and effective freeing of the deck from water. Lower edges of freeing ports should be as
near the deck as practicable.
7.8.3.5 Pound boards and means for stowage and working the fishing gear should be arranged
so that the effectiveness of the freeing ports will not be impaired or water trapped on deck and
prevented from easily reaching the freeing ports. Pound boards should be so constructed that
they can be locked in position when in use and will not hamper the discharge of shipped water.
7.8.3.6 Freeing ports over 0.3 m in depth should be fitted with bars spaced not more
than 0.23 m nor less than 0.15 m apart or provided with other suitable protective arrangements.
Freeing port covers, if fitted, should be of approved construction. If devices are considered
necessary for locking freeing port covers during fishing operations they should be to the
satisfaction of the competent authority and easily operable from a readily accessible position.
7.8.3.7 In vessels intended to operate in areas subject to icing, covers and protective
arrangements for freeing ports should be capable of being easily removed to restrict ice
accumulation. Size of opening and means provided for removal of these protective arrangements
should be to the satisfaction of the competent authority.
7.8.3.8 In addition, in fishing vessels of 12 m in length and above but less than 24 m in length
where wells or cockpits are fitted in the working deck or superstructure deck with their bottoms
above the deepest operating waterline, efficient non-return means of drainage overboard should
be provided. Where bottoms of such wells or cockpits are below the deepest operating waterline,
drainage to the bilges should be provided.
7.8.4 In offshore supply vessels, the Administration should give special attention to adequate
drainage of pipe stowage positions, having regard to the individual characteristics of the vessel.
However, the area provided for drainage of the pipe stowage positions should be in excess of the
required freeing port area in the cargo deck bulwark and should not be fitted with shutters.
7.9
Miscellaneous
7.9.1 Ships engaged in towing operations should be provided with means for quick release of
the towing hawser.
MSC 85/26/Add.1
ANNEX 2
Page 71
CHAPTER 8 DETERMINATION OF LIGHTSHIP PARAMETERS
8.1
Application
8.1.1 Every passenger ship regardless of size and every cargo ship having a length, as defined
in the International Convention on Load Lines, 1966 or the Protocol of 1988 relating thereto,
as amended, as applicable, of 24 m and upwards, should be inclined upon its completion and the
elements of its stability determined.34
8.1.2 The Administration may allow the inclining test of an individual ship as required by
paragraph 8.1.1 to be dispensed with provided basic stability data are available from the inclining
test of a sister ship and it is shown to the satisfaction of the Administration that reliable stability
information for the exempted ship can be obtained from such basic data.
To be dispensed from an inclining test, the deviation of lightship mass is not to exceed,
for L35 < 50 m:
2% of the lightship mass of the lead ship or as given in the

information on stability;
for L > 160 m:
1% of the lightship mass of the lead ship or as given in the

information on stability;
for intermediate L:
by linear interpolation,
and the deviation of the lightships longitudinal centre of gravity (LCG) referred to L should not
be greater than 0.5% of the lightships LCG of the lead ship or as given in the information on
stability regardless of the ships length.
8.1.3 The Administration may allow the inclining test of an individual ship or class of ships
especially designed for the carriage of liquids or ore in bulk to be dispensed with when reference
to existing data for similar ships clearly indicates that due to the ships proportions and
arrangements more than sufficient metacentric height will be available in all probable loading
conditions.
8.1.4 Where any alterations are made to a ship so as to materially affect the stability, the ship
should be re-inclined.
8.1.5 At periodic intervals not exceeding five years, a lightweight survey should be carried out
on all passenger ships to verify any changes in lightship displacement and longitudinal centre of
gravity. The ship should be re-inclined whenever, in comparison with the approved stability
information, a deviation from the lightship displacement exceeding 2% or a deviation of the
longitudinal centre of gravity exceeding 1% of L is found, or anticipated.
8.1.6 The inclining test prescribed is adaptable for ships with a length below 24 m if special
precautions are taken to ensure the accuracy of the test procedure.
34
35
Refer to regulation II-1/5 of the 1974 SOLAS Convention, as amended.

For the purpose of paragraphs 8.1.2 and 8.1.5 the length (L) means the subdivision length (LS) as defined in
regulation II-1/2.1 of the 1974 SOLAS Convention, as amended. For ships to which the Convention applies,
and for other ships the length (L) means the length of ship as defined in 2.12 of the Purpose and Definitions of
this Code.
MSC 85/26/Add.1
ANNEX 2
Page 72
8.2
8.2.1
Notification of the Administration
Written notification of the inclining test should be sent to the Administration as it requires or in
due time before the test. An Administration representative should be present to witness the
inclining test and the test results be submitted for review.
The responsibility for making preparations, conducting the inclining test and lightweight survey,
recording the data, and calculating the results rests with the shipyard, owner or naval architect.
While compliance with the procedures outlined herein will facilitate an expeditious and accurate
inclining test, it is recognized that alternative procedures or arrangements may be equally
efficient. However, to minimize risk of delay, it is recommended that all such variances be
submitted to the Administration for review prior to the inclining test.
8.2.1.1
Details of notification
Written notification should provide the following information as the Administration may require:
.1
identification of the ship by name and shipyard hull number, if applicable;
.2
date, time, and location of the test;
.3
inclining weight data:
.4
.1
type;
.2
amount (number of units and weight of each);
.3
certification;
.4
method of handling (i.e. sliding rail or crane);
.5
anticipated maximum angle of heel to each side;
measuring devices:
.1
pendulums approximate location and length;
.2
U-tubes approximate location and length;
.3
inclinometers location and details of approvals and calibrations;
.5
approximate trim;
.6
condition of tanks;
.7
estimated weights to deduct, to complete, and to relocate in order to place the ship
in its true lightship condition;
MSC 85/26/Add.1
ANNEX 2
Page 73
8.2.2
.8
detailed description of any computer software to be used to aid in calculations

during the inclining test; and
.9
name and telephone number of the person responsible for conducting the inclining
test.
General condition of the ship
8.2.2.1 A ship should be as complete as possible at the time of the inclining test. The test should
be scheduled to minimize the disruption in the ships delivery date or its operational commitments.
8.2.2.2 The amount and type of work left to be completed (mass to be added) affect the
accuracy of the lightship characteristics, so good judgement should be used. If the mass or centre
of gravity of an item to be added cannot be determined with confidence, it is best to conduct the
inclining test after the item is added.
8.2.2.3 Temporary material, tool boxes, staging, sand, debris, etc., on board should be reduced
to absolute minimum before the inclining test. Excess crew or personnel not directly involved in
the inclining test should be removed from on board the ship before the test.
8.2.2.4 Decks should be free of water. Water trapped on deck may shift and pocket in a fashion
similar to liquids in a tank. Any rain, snow or ice accumulated on the ship should be removed
prior to the test.
8.2.2.5 The anticipated liquid loading for the test should be included in the planning for the test.
Preferably, all tanks should be empty and clean, or completely full. The number of slack tanks
should be kept to an absolute minimum. The viscosity of the fluid, the depth of the fluid and the
shape of the tank should be such that the free surface effect can be accurately determined.
8.2.2.6 The ship should be moored in a quiet, sheltered area free from extraneous forces such as
propeller wash from passing vessels, or sudden discharges from shore side pumps. The tide
conditions and the trim of the ship during the test should be considered. Prior to the test, the
depth of water should be measured and recorded in as many locations as are necessary to ensure
that the ship will not contact the bottom. The specific gravity of water should be accurately
recorded. The ship should be moored in a manner to allow unrestricted heeling. The access
ramps should be removed. Power lines, hoses, etc., connected to shore should be at a minimum,
and kept slack at all times.
8.2.2.7 The ship should be as upright as possible; with inclining weights in the initial position,
up to one-half degree of list is acceptable. The actual trim and deflection of keel, if practical,
should be considered in the hydrostatic data. In order to avoid excessive errors caused by
significant changes in the water plane area during heeling, hydrostatic data for the actual trim and
the maximum anticipated heeling angles should be checked beforehand.
8.2.2.8 The total weight used should be sufficient to provide a minimum inclination of one degree
and a maximum of four degrees of heel to each side. The Administration may, however, accept a
smaller inclination angle for large ships provided that the requirements on pendulum deflection or
U-tube difference in height in 8.2.2.9 are complied with. Test weights should be compact and of
such a configuration that the vertical centre of gravity of the weights can be accurately determined.
Each weight should be marked with an identification number and its mass. Re-certification of
the test weights should be carried out prior to the incline. A crane of sufficient capacity and
MSC 85/26/Add.1
ANNEX 2
Page 74
reach, or some other means, should be available during the inclining test to shift weights on the
decking in an expeditious and safe manner. Water ballast transfer may be carried out, when it is
impractical to incline using solid weights if acceptable to the Administration.
8.2.2.9 The use of three pendulums is recommended but a minimum of two should be used to
allow identification of bad readings at any one pendulum station. They should each be located in
an area protected from the wind. One or more pendulums may be substituted by other measuring
devices (U-tubes or inclinometers) at the discretion of the Administration. Alternative measuring
devices should not be used to reduce the minimum inclining angles recommended in 8.2.2.8.
The use of an inclinometer or U-tube should be considered in each separate case. It is
recommended that inclinometers or other measuring devices only be used in conjunction with at
least one pendulum.
8.2.2.10 Efficient two-way communications should be provided between central control and
the weight handlers and between central control and each pendulum station. One person at a
central control station should have complete control over all personnel involved in the test.
8.3
Plans required
The person in charge of the inclining test should have available a copy of the following plans at
the time of the inclining test:
8.4
.1
lines plan;
.2
hydrostatic curves or hydrostatic data;
.3
general arrangement plan of decks, holds, inner bottoms, etc.;
.4
capacity plan showing capacities and vertical and longitudinal centres of gravity
of cargo spaces, tanks, etc. When ballast water is used as inclining weight, the
transverse and vertical centres of gravity for the applicable tanks for each angle of
inclination, must be available;
.5
tank sounding tables;
.6
draught mark locations; and
.7
docking drawing with keel profile and draught mark corrections (if available).
Test procedure
8.4.1 Procedures followed in conducting the inclining test and lightweight survey should be in
accordance with the recommendations laid out in annex 1 (Detailed guidance for the conduct of
an inclining test) to this Code.
8.4.1.1 Freeboard/draught readings should be taken to establish the position of the waterline in
order to determine the displacement of the ship at the time of the inclining test. It is recommended
that at least five freeboard readings, approximately equally spaced, be taken on each side of the ship
or that all draught marks (forward, midship and aft) be read on each side of the ship. Draught/
freeboard readings should be read immediately before or immediately after the inclining test.
MSC 85/26/Add.1
ANNEX 2
Page 75
8.4.1.2 The standard test employs eight distinct weight movements. Movement No.8, a recheck
of the zero point, may be omitted if a straight line plot is achieved after movement No.7. If a
straight line plot is achieved after the initial zero and six weight movements, the inclining test is
complete and the second check at zero may be omitted. If a straight line plot is not achieved, those
weight movements that did not yield acceptable plotted points should be repeated or explained.
8.4.2 A copy of the inclining data should be forwarded to the Administration along with the
calculated results of the inclining test in an acceptable report format, if required.
8.4.3 All calculations performed during the inclining test and in preparation of an inclining test
report may be carried out by a suitable computer program. Output generated by such a program
may be used for presentation of all or partial data and calculations included in the test report if it is
clear, concise, well documented, and generally consistent in form and content with Administration
requirements.
8.5
Inclining test for MODUs
8.5.1 An inclining test should be required for the first unit of a design, when as near to completion
as possible, to determine accurately the lightship data (weight and position of centre of gravity).
8.5.2 For successive units which are identical by design, the lightship data of the first unit of the
series may be accepted by the Administration in lieu of an inclining test, provided the difference
in lightship displacement or position of centre of gravity due to weight changes for minor
differences in machinery, outfitting or equipment, confirmed by the results of a deadweight survey,
are less than 1% of the values of the lightship displacement and principal horizontal dimensions as
determined for the first of the series. Extra care should be given to the detailed weight calculation
and comparison with the original unit of a series of column-stabilized, semi-submersible types as
these, even though identical by design, are recognized as being unlikely to attain an acceptable
similarity of weight or centre of gravity to warrant a waiver of the inclining test.
8.5.3 The results of the inclining test, or deadweight survey and inclining experiment adjusted
for weight differences, should be indicated in the Operating Manual.
8.5.4 A record of all changes to machinery, structure, outfit and equipment that affect the
lightship data, should be maintained in the Operating Manual or a lightship data alterations log
and be taken into account in daily operations.
8.5.5 For column-stabilized units, a deadweight survey should be conducted at intervals not
exceeding five years. Where the deadweight survey indicates a change from the calculated lightship
displacement in excess of 1% of the operating displacement, an inclining test should be conducted.
8.5.6 An inclining test or a deadweight survey should be carried out in the presence of an officer
of the Administration, or a duly authorized person or representative of an approved organization.
8.6
Stability test for pontoons
An inclining experiment is not normally required for a pontoon, provided a conservative value of
the lightship vertical centre of gravity (KG) is assumed for the stability calculations. The KG can
be assumed at the level of the main deck although it is recognized that a lesser value could be
acceptable if fully documented. The lightship displacement and longitudinal centre of gravity
should be determined by calculation based on draught and density readings.
MSC 85/26/Add.1
ANNEX 2
Page 76
ANNEX 1
DETAILED GUIDANCE FOR THE CONDUCT OF AN INCLINING TEST
1
INTRODUCTION
This annex supplements the inclining standards put forth in part B, chapter 8 (Determination of
lightship parameters) of this Code. This annex contains important detailed procedures for
conducting an inclining test in order to ensure that valid results are obtained with maximum
precision at a minimal cost to owners, shipyards and the Administration. A complete
understanding of the correct procedures used to perform an inclining test is imperative in order to
ensure that the test is conducted properly and so that results can be examined for accuracy as the
inclining experiment is conducted.
2
PREPARATIONS FOR THE INCLINING TEST
2.1
Free surface and tankage
2.1.1 If there are liquids on board the ship when it is inclined, whether in the bilges or in the tanks,
they will shift to the low side when the ship heels. This shift of liquids will exaggerate the heel
of the ship. Unless the exact weight and distance of liquid shifted can be precisely calculated, the
metacentric height (GM) calculated from the inclining test will be in error. Free surface should be
minimized by emptying the tanks completely and making sure all bilges are dry; or by completely
filling the tanks so that no shift of liquid is possible. The latter method is not the optimum because
air pockets are difficult to remove from between structural members of a tank, and the weight and
centre of the liquid in a full tank should be accurately determined in order to adjust the lightship
values accordingly. When tanks must be left slack, it is desirable that the sides of the tanks be
parallel vertical planes and the tanks be regular in shape (i.e. rectangular, trapezoidal, etc.) when
viewed from above, so that the free surface moment of the liquid can be accurately determined.
For example, the free surface moment of the liquid in a tank with parallel vertical sides can be
readily calculated by the formula:
Mfs = l*b*t/12 (mt)
where:
l
= length of tank (m)
= breadth of tank (m)
= specific gravity of liquid in tank (t/m)
M (1) + M (2) + ..... + M (x )

fs
Free surface correction =

where:
Mfs = free surface moment (mt)
= displacement (t)
fs
fs
( m)
MSC 85/26/Add.1
ANNEX 2
Page 77
Free surface correction is independent of the height of the tank in the ship, location of the tank,
and direction of heel. As the width of the tank increases, the value of free surface moment
increases by the third power. The distance available for the liquid to shift is the predominant
factor. This is why even the smallest amount of liquid in the bottom of a wide tank or bilge is
normally unacceptable and should be removed prior to the inclining experiment. Insignificant
amounts of liquids in V-shaped tanks or voids (e.g., a chain locker in the bow), where the
potential shift is negligible, may remain if removal of the liquid would be difficult or would
cause extensive delays.
When ballast water is used as inclining weight, the actual transverse and vertical movements of
the liquid should be calculated taking into account the change of heel of the ship. Free surface
corrections as defined in this paragraph should not apply to the inclining tanks.
2.1.2 Free surface and slack tanks: The number of slack tanks should normally be limited to
one port/starboard pair or one centreline tank of the following:
.1
fresh water reserve feed tanks;
.2
fuel/diesel oil storage tanks;
.3
fuel/diesel oil day tanks;
.4
lube oil tanks;
.5
sanitary tanks; or
.6
potable water tanks.
To avoid pocketing, slack tanks should normally be of regular (i.e. rectangular, trapezoidal, etc.)
cross section and be 20% to 80% full if they are deep tanks and 40% to 60% full if they are
double-bottom tanks. These levels ensure that the rate of shifting of liquid remains constant
throughout the heel angles of the inclining test. If the trim changes as the ship is inclined, then
consideration should also be given to longitudinal pocketing. Slack tanks containing liquids of
sufficient viscosity to prevent free movement of the liquids, as the ship is inclined (such as
bunker at low temperature), should be avoided since the free surface cannot be calculated
accurately. A free surface correction for such tanks should not be used unless the tanks are
heated to reduce viscosity. Communication between tanks should never be allowed.
Cross-connections, including those via manifolds, should be closed. Equal liquid levels in slack
tank pairs can be a warning sign of open cross connections. A bilge, ballast, and fuel oil piping
plan can be referred to, when checking for cross connection closures.
2.1.3 Pressed-up tanks: Pressed up means completely full with no voids caused by trim or
inadequate venting. Anything less than 100% full, for example the 98% condition regarded as
full for operational purposes, is not acceptable. Preferably, the ship should be rolled from side to
side to eliminate entrapped air before taking the final sounding. Special care should be taken
when pressing fuel oil tanks to prevent accidental pollution. An example of a tank that would
appear pressed up, but actually contains entrapped air, is shown in figure A1-2.1.3.
MSC 85/26/Add.1
ANNEX 2
Page 78
Figure A1-2.1.3
2.1.4 Empty tanks: It is generally not sufficient to simply pump tanks until suction is lost.
Enter the tank after pumping to determine if final stripping with portable pumps or by hand is
necessary. The exceptions are very narrow tanks or tanks where there is a sharp deadrise, since
free surface would be negligible. Since all empty tanks should be inspected, all manholes should
be open and the tanks well ventilated and certified as safe for entry. A safe testing device should
be on hand to test for sufficient oxygen and minimum toxic levels. A certified marine chemists
certificate certifying that all fuel oil and chemical tanks are safe for human entry should be
available, if necessary.
2.2
Mooring arrangements
The importance of good mooring arrangements cannot be overemphasized. The arrangement

selections will be dependent upon many factors. Among the most important are depth of water,
wind and current effects. Whenever possible, the ship should be moored in a quiet, sheltered
area free from extraneous forces such as propeller wash from passing ships, or sudden discharges
from shore side pumps. The depth of water under the hull should be sufficient to ensure that the
hull will be entirely free of the bottom. The tide conditions and the trim of the ship during the
test should be considered. Prior to the test, the depth of water should be measured and recorded
in as many locations as necessary to ensure the ship will not contact the bottom. If marginal, the
test should be conducted during high tide or the ship moved to deeper water.
2.2.1 The mooring arrangement should ensure that the ship will be free to list without restraint
for a sufficient period of time to allow a satisfactory reading of the heeling angle, due to each
weight shift, to be recorded.
2.2.2 The ship should be held by lines at the bow and the stern, attached to bollards and/or
cleats on the deck. If suitable restraint of the ship cannot be achieved using deck fittings, then
temporary padeyes should be attached as close as possible to the centreline of the ship and as
near the waterline as practical. Where the ship can be moored to one side only, it is good
practice to supplement the bow and stern lines with two spring lines in order to maintain positive
control of the ship, as shown in figure A1-2.2.2. The leads of the spring lines should be as long
as practicable. Cylindrical camels should be provided between the ship and the dock. All lines
should be slack, with the ship free of the pier and camels, when taking readings.
MSC 85/26/Add.1
ANNEX 2
Page 79
Figure A1-2.2.2
2.2.2.1 If the ship is held off the pier by the combined effect of the wind and current, a
superimposed heeling moment will act on the ship throughout the test. For steady conditions this
will not affect the results. Gusty winds or uniformly varying wind and/or current will cause these
superimposed heeling moments to change, which may require additional test points to obtain a
valid test. The need for additional test points can be determined by plotting test points as they
are obtained.
2.2.2.2 If the ship is pressed against the fenders by wind and/or current, all lines should be
slack. The cylindrical camels will prevent binding but there will be an additional superimposed
heeling moment due to the ship bearing against the camels. This condition should be avoided
where possible but, when used, consideration should be given to pulling the ship free of the dock
and camels and letting the ship drift as readings are taken.
2.2.2.3 Another acceptable arrangement is where the combined wind and current are such that
the ship may be controlled by only one line at either the bow or the stern. In this case, the control
line should be led from on or near the centreline of the ship with all lines but the control line
slack, the ship is free to veer with the wind and/or current as readings are taken. This can
sometimes be troublesome because varying wind and/or current can cause distortion of the plot.
2.2.3 The mooring arrangement should be submitted to the approval authority for review prior
to the test.
2.2.4
If a floating crane is used for handling inclining weights, it should not be moored to the ship.
2.3
Test weights
2.3.1 Weights, such as porous concrete, that can absorb significant amounts of moisture should
only be used if they are weighed just prior to the inclining test or if recent weight certificates are
presented. Each weight should be marked with an identification number and its weight. For
small ships, drums completely filled with water may be used. Drums should normally be full and
capped to allow accurate weight control. In such cases, the weight of the drums should be
verified in the presence of the Administration representative using a recently calibrated scale.
2.3.2 Precautions should be taken to ensure that the decks are not overloaded during weight
movements. If deck strength is questionable then a structural analysis should be performed to
determine if existing framing can support the weight.
MSC 85/26/Add.1
ANNEX 2
Page 80
2.3.3 Generally, the test weights should be positioned as far outboard as possible on the upper deck.
The test weights should be on board and in place prior to the scheduled time of the inclining test.
2.3.4 Where the use of solid weights to produce the inclining moment is demonstrated to be
impracticable, the movement of ballast water may be permitted as an alternative method. This
acceptance would be granted for a specific test only, and approval of the test procedure by the
Administration is required. As a minimal prerequisite for acceptability, the following conditions
should be required:
2.4
.1
inclining tanks should be wall-sided and free of large stringers or other internal
members that create air pockets. Other tank geometries may be accepted at the
discretion of the Administration;
.2
tanks should be directly opposite to maintain ships trim;
.3
specific gravity of ballast water should be measured and recorded;
.4
pipelines to inclining tanks should be full. If the ships piping layout is unsuitable
for internal transfer, portable pumps and pipes/hoses may be used;
.5
blanks must be inserted in transfer manifolds to prevent the possibility of liquids

being leaked during transfer. Continuous valve control must be maintained
during the test;
.6
all inclining tanks must be manually sounded before and after each shift;
.7
vertical, longitudinal and transverse centres should be calculated for each movement;
.8
accurate sounding/ullage tables must be provided. The ships initial heel angle
should be established prior to the incline in order to produce accurate values for
volumes and transverse and vertical centres of gravity for the inclining tanks at
every angle of heel. The draught marks amidships (port and starboard) should be
used when establishing the initial heel angle;
.9
verification of the quantity shifted may be achieved by a flow meter or similar

device; and
.10
the time to conduct the inclining must be evaluated. If time requirements for
transfer of liquids are considered too long, water may be unacceptable because of
the possibility of wind shifts over long periods of time.
Pendulums
2.4.1 The pendulums should be long enough to give a measured deflection, to each side of
upright, of at least 15 cm. Generally, this will require a pendulum length of at least 3 m. It is
recommended that pendulum lengths of 4 to 6 m be used. Usually, the longer the pendulum the
greater the accuracy of the test; however, if excessively long pendulums are used on a tender ship
the pendulums may not settle down and the accuracy of the pendulums would then be
questionable. On large ships with high GM, pendulum lengths in excess of the length
recommended above may be required to obtain the minimum deflection. In such cases, the
trough, as shown in figure A1-2.4.6, should be filled with high-viscosity oil. If the pendulums
are of different lengths, the possibility of collusion between station recorders is avoided.
MSC 85/26/Add.1
ANNEX 2
Page 81
2.4.2 On smaller ships, where there is insufficient headroom to hang long pendulums,
the 15 cm deflection should be obtained by increasing the test weight so as to increase the heel.
On most ships the typical inclination is between one and four degrees.
2.4.3 The pendulum wire should be piano wire or other monofilament material. The top
connection of the pendulum should afford unrestricted rotation of the pivot point. An example is
that of a washer with the pendulum wire attached suspended from a nail.
2.4.4 A trough filled with a liquid should be provided to dampen oscillations of the pendulum
after each weight movement. It should be deep enough to prevent the pendulum weight from
touching the bottom. The use of a winged plumb bob at the end of the pendulum wire can also
help to dampen the pendulum oscillations in the liquid.
2.4.5 The battens should be smooth, light-coloured wood, 1 to 2 cm thick, and should be
securely fixed in position so that an inadvertent contact will not cause them to shift. The batten
should be aligned close to the pendulum wire but not in contact with it.
2.4.6 A typical satisfactory arrangement is shown in figure A1-2.4.6. The pendulums may be
placed in any location on the ship, longitudinally and transversely. The pendulums should be in
place prior to the scheduled time of the inclining test.
2.4.7 It is recommended that inclinometers or other measuring devices only be used in
conjunction with at least one pendulum. The Administration may approve an alternative
arrangement when this is found impractical.
Figure A1-2.4.6
2.5
U-tubes
2.5.1 The legs of the device should be securely positioned as far as outboard as possible and
should be parallel to the centreline plane of the ship. The distance between the legs should be
measured perpendicular to the centreline plane. The legs should be vertical, as far as practical.
MSC 85/26/Add.1
ANNEX 2
Page 82
2.5.2 Arrangements should be made for recording all readings at both legs. For easy reading
and checking for air pockets, clear plastic tube or hose should be used throughout. The U-tube
should be pressure-tested prior to the inclining test to ensure watertightness.
2.5.3 The horizontal distance between the legs of the U-tube should be sufficient to obtain a
level difference of at least 15 cm between the upright and the maximum inclination to each side.
2.5.4 Normally, water would be used as the liquid in the U-tube. Other low-viscosity liquids
may also be considered.
2.5.5 The tube should be free of air pockets. Arrangements should be made to ensure that the
free flow of the liquid in the tube is not obstructed.
2.5.6 Where a U-tube is used as a measuring device, due consideration should be given to the
prevailing weather conditions (see 4.1.1.3):
2.6
.1
if the U-tube is exposed to direct sunlight, arrangements should be made to avoid

temperature differences along the length of the tube;
.2
if temperatures below 0C are expected, the liquid should be a mixture of water

and an anti-freeze additive; and
.3
where heavy rain squalls can be expected, arrangements should be made to avoid
additional water entering the U-tube.
Inclinometers
The use of inclinometers should be subject to at least the following recommendations:

.1
the accuracy should be equivalent to that of the pendulum;
.2
the sensitivity of the inclinometer should be such that the non-steady heeling angle
of the ship can be recorded throughout the measurement;
.3
the recording period should be sufficient to accurately measure the inclination.

The recording capacity should be generally sufficient for the whole test;
.4
the instrument should be able to plot or print the recorded inclination angles on
paper;
.5
the instrument should have linear performance over the expected range of
inclination angles;
.6
the instrument should be supplied with the manufacturers instructions giving

details of calibration, operating instructions, etc.; and
.7
it should be possible to demonstrate the required performance to the satisfaction of

the Administration during the inclining test.
MSC 85/26/Add.1
ANNEX 2
Page 83
3
EQUIPMENT REQUIRED
Besides the physical equipment necessary such as the inclining weights, pendulums, small boat,
etc., the following are necessary and should be provided by or made available to the person in
charge of the inclining:
.1
engineering scales for measuring pendulum deflections (rules should be

subdivided sufficiently to achieve the desired accuracy;
.2
sharp pencils for marking pendulum deflections;
.3
chalk for marking the various positions of the inclining weights;
.4
a sufficiently long measuring tape for measuring the movement of the weights and
locating different items on board;
.5
a sufficiently long sounding tape for sounding tanks and taking freeboard readings;
.6
one or more well maintained specific gravity hydrometers with range sufficient to
cover 0.999 to 1.030, to measure the specific gravity of the water in which the
ship is floating (a hydrometer for measuring specific gravity of less than 1.000
may be needed in some locations);
.7
other hydrometers as necessary to measure the specific gravity of any liquids

on board;
.8
graph paper to plot inclining moments versus tangents;
.9
a straight edge to draw the measured waterline on the lines drawing;
.10
a pad of paper to record data;
.11
an explosion-proof testing device to check for sufficient oxygen and absence of

lethal gases in tanks and other closed spaces such as voids and cofferdams;
.12
a thermometer; and
.13
draught tubes (if necessary).
TEST PROCEDURE
The inclining experiment, the freeboard/draught readings and the survey may be conducted in
any order and still achieve the same results. If the person conducting the inclining test is
confident that the survey will show that the ship is in an acceptable condition and there is the
possibility of the weather becoming unfavourable, then it is suggested that the inclining be
performed first and the survey last. If the person conducting the test is doubtful that the ship is
complete enough for the test, it is recommended that the survey be performed first since this
could invalidate the entire test, regardless of the weather conditions. It is very important that all
weights, the number of people on board, etc., remain constant throughout the test.
MSC 85/26/Add.1
ANNEX 2
Page 84
4.1
Initial walk through and survey
The person responsible for conducting the inclining test should arrive on board the ship well in
advance of the scheduled time of the test to ensure that the ship is properly prepared for the test.
If the ship to be inclined is large, a preliminary walk through may need to be done the day
preceding the actual incline. To ensure the safety of personnel conducting the walk through, and
to improve the documentation of surveyed weights and deficiencies, at least two persons should
make the initial walk through. Things to check include: all compartments are open, clean, and
dry, tanks are well ventilated and gas-free, movable or suspended items are secured and their
position documented, pendulums are in place, weights are on board and in place, a crane or other
method for moving weights is available, and the necessary plans and equipment are available.
Before beginning the inclining test, the person conducting the test should:
.1
consider the weather conditions. The combined adverse effect of wind, current
and sea may result in difficulties or even an invalid test due to the following:
.1
inability to accurately record freeboards and draughts;
.2
excessive or irregular oscillations of the pendulums;
.3
variations in unavoidable superimposed heeling moments.
In some instances, unless conditions can be sufficiently improved by moving the

ship to a better location, it may be necessary to delay or postpone the test. Any
significant quantities of rain, snow, or ice should be removed from the ship before
the test. If bad weather conditions are detected early enough and the weather
forecast does not call for improving conditions, the Administration representative
should be advised prior to departure from the office and an alternative date
scheduled;
.2
make a quick overall survey of the ship to make sure the ship is complete enough
to conduct the test and to ensure that all equipment is in place. An estimate of
items which will be outstanding at the time of the inclining test should be included
as part of any test procedure submitted to the Administration. This is required so
that the Administration representative can advise the shipyard/naval architect if in
their opinion the ship will not be sufficiently complete to conduct the incline and
that it should be rescheduled. If the condition of the ship is not accurately
depicted in the test procedure and at the time of the inclining test the
Administration representative considers that the ship is in such condition that an
accurate incline cannot be conducted, the representative may refuse to accept the
incline and require that the incline be conducted at a later date;
.3
enter all empty tanks after it is determined that they are well ventilated and gas-free
to ensure that they are dry and free of debris. Ensure that any pressed-up tanks are
indeed full and free of air pockets. The anticipated liquid loading for the incline
should be included in the procedure required to be submitted to the Administration;
.4
survey the entire ship to identify all items which need to be added to the ship,
removed from the ship, or relocated on the ship to bring the ship to the lightship
condition. Each item should be clearly identified by weight and vertical and
longitudinal location. If necessary, the transverse location should also be
MSC 85/26/Add.1
ANNEX 2
Page 85
recorded. The inclining weights, the pendulums, any temporary equipment and
dunnage, and the people on board during the inclining test are all among the
weights to be removed to obtain the lightship condition. The person calculating
the lightship characteristics from the data gathered during the incline and survey
and/or the person reviewing the inclining test may not have been present during
the test and should be able to determine the exact location of the items from the
data recorded and the ships drawings. Any tanks containing liquids should be
accurately sounded and the soundings recorded;
.5
it is recognized that the weight of some items on board, or that are to be added,
may have to be estimated. If this is necessary, it is in the best interest of safety to
be on the safe side when estimating, so the following rules of thumb should be
followed:
.1
.2
.3
4.2
when estimating weights to be added:

.1.1
estimate high for items to be added high in the ship; and
.1.2
estimate low for items to be added low in the ship;
when estimating weights to be removed:

.2.1
estimate low for items to be removed from high in the ship; and
.2.2
estimate high for items to be removed from low in the ship;
when estimating weights to be relocated:

.3.1
estimate high for items to be relocated to a higher point in the ship;

and
.3.2
estimate low for items to be relocated to a lower point in the ship.
Freeboard/draught readings
4.2.1 Freeboard/draught readings should be taken to establish the position of the waterline in
order to determine the displacement of the ship at the time of the inclining test. It is
recommended that at least five freeboard readings, approximately equally spaced, be taken on
each side of the ship or that all draught marks (forward, midship, and aft) be read on each side of
the ship. Draught mark readings should be taken to assist in determining the waterline defined
by freeboard readings, or to verify the vertical location of draught marks on ships where their
location has not been confirmed. The locations for each freeboard reading should be clearly
marked. The longitudinal location along the ship should be accurately determined and recorded
since the (moulded) depth at each point will be obtained from the ships lines. All freeboard
measurements should include a reference note clarifying the inclusion of the coaming in the
measurement and the coaming height.
4.2.2 Draught and freeboard readings should be read immediately before or immediately after the
inclining test. Weights should be on board and in place and all personnel who will be on board
during the test, including those who will be stationed to read the pendulums, should be on board
and in location during these readings. This is particularly important on small ships. If readings
MSC 85/26/Add.1
ANNEX 2
Page 86
are made after the test, the ship should be maintained in the same condition as during the test.
For small ships, it may be necessary to counterbalance the list and trim effects of the freeboard
measuring party. When possible, readings should be taken from a small boat.
4.2.3 A small boat should be available to aid in the taking of freeboard and draught mark
readings. It should have low freeboard to permit accurate observation of the readings.
4.2.4 The specific gravity of the flotation water should be determined at this time. Samples should
be taken from a sufficient depth of the water to ensure a true representation of the flotation water
and not merely surface water, which could contain fresh water from run-off of rain. A hydrometer
should be placed in a water sample and the specific gravity read and recorded. For large ships, it
is recommended that samples of the flotation water be taken forward, midship, and aft and the
readings averaged. For small ships, one sample taken from midships should be sufficient. The
temperature of the water should be taken and the measured specific gravity corrected for deviation
from the standard, if necessary. A correction to water specific gravity is not necessary if the
specific gravity is determined at the inclining experiment site. Correction is necessary if specific
gravity is measured when sample temperature differs from the temperature at the time of the
inclining (e.g., if check of specific gravity is done at the office).
4.2.5 A draught mark reading may be substituted for a given freeboard reading at that
longitudinal location if the height and location of the mark have been verified to be accurate by a
keel survey while the ship was in dry dock.
4.2.6 A device, such as a draught tube, can be used to improve the accuracy of
freeboard/draught readings by damping out wave action.
4.2.7 The dimensions given on a ships lines drawing are normally moulded dimensions. In the
case of depth, this means the distance from the inside of the bottom shell to the inside of the deck
plate. In order to plot the ships waterline on the lines drawing, the freeboard readings should be
converted to moulded draughts. Similarly, the draught mark readings should be corrected from
extreme (bottom of keel) to moulded (top of keel) before plotting. Any discrepancy between the
freeboard/draught readings should be resolved.
4.2.8 The mean draught (average of port and starboard readings) should be calculated for each of
the locations where freeboard/draught readings are taken and plotted on the ships lines drawing or
outboard profile to ensure that all readings are consistent and together define the correct waterline.
The resulting plot should yield either a straight line or a waterline which is either hogged or
sagged. If inconsistent readings are obtained, the freeboards/draughts should be retaken.
4.3
The incline
4.3.1 Prior to any weight movements the following should be checked:

.1
the mooring arrangement should be checked to ensure that the ship is floating
freely (this should be done just prior to each reading of the pendulums);
.2
the pendulums should be measured and their lengths recorded. The pendulums
should be aligned so that when the ship heels, the wire will be close enough to the
batten to ensure an accurate reading but will not come into contact with the batten.
The typical satisfactory arrangement is shown in figure A1-2.4.6;
MSC 85/26/Add.1
ANNEX 2
Page 87
.3
the initial position of the weights is marked on the deck. This can be done by
tracing the outline of the weights on the deck;
.4
the communications arrangement is adequate; and
.5
all personnel are in place.
4.3.2 A plot should be run during the test to ensure that acceptable data are being obtained.
Typically, the abscissa of the plot will be heeling moment W(x) (weight times distance x) and the
ordinate will be the tangent of the heel angle (deflection of the pendulum divided by the length of
the pendulum). This plotted line does not necessarily pass through the origin or any other
particular point for no single point is more significant than any other point. A linear regression
analysis is often used to fit the straight line. The weight movements shown in figure A2-4.3.2-1
give a good spread of points on the test plot.
Figure A1-4.3.2-1
The plotting of all the readings for each of the pendulums during the inclining experiment aids in
the discovery of bad readings. Since W(x)/tan should be constant, the plotted line should be
straight. Deviations from a straight line are an indication that there were other moments acting
on the ship during the inclining. These other moments should be identified, the cause corrected,
and the weight movements repeated until a straight line is achieved. Figures A1-4.3.2-2
to A1-4.3.2-5 illustrate examples of how to detect some of these other moments during the
inclining, and a recommended solution for each case. For simplicity, only the average of the
readings is shown on the inclining plots.
MSC 85/26/Add.1
ANNEX 2
Page 88
Figure A1-4.3.2-2
Figure A1-4.3.2-3
Figure A1-4.3.2-4
Figure A1-4.3.2-5
MSC 85/26/Add.1
ANNEX 2
Page 89
4.3.3 Once everything and everyone is in place, the zero position should be obtained and the
remainder of the experiment conducted as quickly as possible, while maintaining accuracy and
proper procedures, in order to minimize the possibility of a change in environmental conditions
during the test.
4.3.4 Prior to each pendulum reading, each pendulum station should report to the control
station when the pendulum has stopped swinging. Then, the control station will give a standby
warning and then a mark command. When mark is given, the batten at each position should
be marked at the location of the pendulum wire. If the wire was oscillating slightly, the centre of
the oscillations should be taken as the mark. If any of the pendulum readers does not think the
reading was a good one, the reader should advise the control station and the point should be
retaken for all pendulum stations. Likewise, if the control station suspects the accuracy of a
reading, it should be repeated for all the pendulum stations. Next to the mark on the batten
should be written the number of the weight movement, such as zero for the initial position and
one to seven for the weight movements.
4.3.5 Each weight movement should be made in the same direction, normally transversely, so
as not to change the trim of the ship. After each weight movement, the distance the weight was
moved (centre to centre) should be measured and the heeling moment calculated by multiplying
the distance by the amount of weight moved. The tangent is calculated for each pendulum by
dividing the deflection by the length of the pendulum. The resultant tangents are plotted on the
graph. Provided there is good agreement among the pendulums with regard to the tan value,
the average of the pendulum readings may be graphed instead of plotting each of the readings.
4.3.6 Inclining data sheets should be used so that no data are forgotten and so that the data are
clear, concise, and consistent in form and format. Prior to departing the ship, the person
conducting the test and the Administration representative should initial each data sheet as an
indication of their concurrence with the recorded data.
MSC 85/26/Add.1
ANNEX 2
Page 90
ANNEX 2
RECOMMENDATIONS FOR SKIPPERS OF FISHING VESSELS ON ENSURING
A VESSELS ENDURANCE IN CONDITIONS OF ICE FORMATION
1
Prior to departure
1.1
Firstly, the skipper should, as in the case of any voyages in any season, ensure that the
vessel is generally in a seaworthy condition, giving full attention to basic requirements such as:
1.2
.1
loading of the vessel within the limits prescribed for the season (paragraph 1.2.1
below);
.2
weathertightness and reliability of the devices for closing cargo and access
hatches, outer doors and all other openings in the decks and superstructures of the
vessel and the watertightness of the sidescuttles and of ports or similar openings in
the sides below the freeboard deck to be checked;
.3
condition of the freeing ports and scuppers as well as operational reliability of

their closures to be checked;
.4
emergency and life-saving appliances and their operational reliability;
.5
operational reliability of all external and internal communication equipment; and
.6
condition and operational reliability of the bilge and ballast pumping systems.
Further, with special regard to possible ice accretion, the skipper should:
.1
consider the most critical loading condition against approved stability documents
with due regard to fuel and water consumption, distribution of supplies, cargoes
and fishing gear and with allowance for possible ice accretion;
.2
be aware of the danger in having supplies and fishing gear stored on open weather
deck spaces due to their large ice accretion surface and high centre of gravity;
.3
ensure that a complete set of warm clothing for all members of the crew is
available on the vessel as well as a complete set of hand tools and other appliances
for combating ice accretion, a typical list thereof for small vessels is shown in
section 4 of this annex;
.4
ensure that the crew is acquainted with the location of means for combating ice
accretion, as well as the use of such means, and that drills are carried out so that
members of the crew know their respective duties and have the necessary practical
skills to ensure the vessels endurance under conditions of ice accretion;
.5
acquaint himself with the meteorological conditions in the region of fishing

grounds and en route to the place of destination; study the synoptical maps of this
region and weather forecasts; be aware of warm currents in the vicinity of the
fishing grounds, of the nearest coastline relief, of the existence of protected bays
and of the location of ice fields and their boundaries; and
MSC 85/26/Add.1
ANNEX 2
Page 91
.6
acquaint himself with the timetable of the radio stations transmitting weather
forecasts and warnings of the possibility of ice accretion in the area of the relevant
fishing grounds.
At sea
2.1
During the voyage and when the vessel is on the fishing grounds, the skipper should keep
himself informed on all long-term and short-term weather forecasts and should arrange for the
following systematic meteorological observations to be systematically recorded:
.1
temperatures of the air and of the sea surface;
.2
wind direction and force;
.3
direction and height of waves and sea state;
.4
atmospheric pressure, air humidity; and
.5
frequency of splashing per minute and the intensity of ice accumulation on different
parts of the vessel per hour.
2.2
All observed data should be recorded in the vessels log-book. The skipper should
compare the weather forecasts and icing charts with actual meteorological conditions, and should
estimate the probability of ice formation and its intensity.
2.3
When the danger of ice formation arises, the following measures should be taken without
delay:
.1
all the means of combating ice formation should be ready for use;
.2
all the fishing operations should be stopped, the fishing gear should be taken on
board and placed in the under-deck spaces. If this cannot be done all the gear
should be fastened for storm conditions on its prescribed place. It is particularly
dangerous to leave the fishing gear suspended since its surface for ice formation is
large and the point of suspension is generally located high;
.3
barrels and containers with fish, packing, all gear and supplies located on deck as
well as portable mechanisms should be placed in closed spaces as low as possible
and firmly lashed;
.4
all cargoes in holds and other compartments should be placed as low as possible
and firmly lashed;
.5
the cargo booms should be lowered and fastened;
.6
deck machinery, hawser reels and boats should be covered with duck covers;
.7
lifelines should be fastened on deck;
.8
freeing ports fitted with covers should be brought into operative condition, all
objects located near scuppers and freeing ports and preventing water drainage
from deck should be taken away;
MSC 85/26/Add.1
ANNEX 2
Page 92
.9
all cargo and companion hatches, manhole covers, weathertight outside doors in
superstructures and deck-houses and portholes should be securely closed in order
to ensure complete weathertightness of the vessel, access to the weather deck from
inner compartments should be allowed only through the superstructure deck;
.10
a check should be carried out as to whether the amount of water ballast on board
and its location is in accordance with that recommended in Stability guidance to
skippers; if there is sufficient freeboard, all the empty bottom tanks fitted with
ballast piping should be filled with seawater;
.11
all fire-fighting, emergency and life-saving equipment should be ready for use;
.12
all drainage systems should be checked for their effectiveness;
.13
deck lighting and searchlights should be checked;
.14
a check should be carried out to make sure that each member of the crew has
warm clothing; and
.15
reliable two-way radio communication with both shore stations and other vessels
should be established; radio calls should be arranged for set times.
2.4
The skipper should seek to take the vessel away from the dangerous area, keeping in mind
that the lee edges of icefields, areas of warm currents and protected coastal areas are a good
refuge for the vessel during weather when ice formation occurs.
2.5
Small fishing vessels on fishing grounds should keep nearer to each other and to larger
vessels.
2.6
It should be remembered that the entry of the vessel into an icefield presents certain
danger to the hull, especially when there is a high sea swell. Therefore the vessel should enter
the icefield at a right angle to the icefield edge at low speed without inertia. It is less dangerous
to enter an icefield bow to the wind. If a vessel must enter an icefield with the wind on the stern,
the fact that the edge of the ice is more dense on the windward side should be taken into
consideration. It is important to enter the icefield at the point where the ice floes are the smallest.
3
During ice formation
3.1
If in spite of all measures taken the vessel is unable to leave the dangerous area, all means
available for removal of ice should be used as long as it is subjected to ice formation.
3.2
Depending on the type of vessel, all or many of the following ways of combating ice
formation may be used:
.1
removal of ice by means of cold water under pressure;
.2
removal of ice with hot water and steam; and
.3
breaking up of ice with ice crows, axes, picks, scrapers, or wooden

sledge-hammers and clearing it with shovels.
MSC 85/26/Add.1
ANNEX 2
Page 93
3.3
When ice formation begins, the skipper should take into account the recommendations
listed below and ensure their strict fulfilment:
.1
report immediately ice formation to the shipowner and establish with him constant
radio communication;
.2
establish radio communication with the nearest vessels and ensure that it is
maintained;
.3
do not allow ice formation to accumulate on the vessel, immediately take steps to
remove from the vessels structures even the thinnest layer of ice and ice sludge
from the upper deck;
.4
check constantly the vessels stability by measuring the roll period of the vessel
during ice formation. If the rolling period increases noticeably, immediately take
all possible measures in order to increase the vessels stability;
.5
ensure that each member of the crew working on the weather deck is warmly
dressed and wears a safety line securely attached to the guardrail;
.6
bear in mind that the work of the crew on ice clearing entails the danger of
frost-bite. For this reason it is necessary to make sure that members of the crew
working on deck are replaced periodically;
.7
keep the following structures and gears of the vessel first free from ice:
.7.1
aerials;
.7.2
running and navigational lights;
.7.3
freeing ports and scuppers;
.7.4
lifesaving craft;
.7.5
stays, shrouds, masts and rigging;
.7.6
doors of superstructures and deck-houses; and
.7.7
windlass and hawse holes;
.8
remove the ice from large surfaces of the vessel, beginning with the upper
structures (such as bridges, deck-houses, etc.), because even a small amount of ice
on them causes a drastic worsening of the vessels stability;
.9
when the distribution of ice is not symmetrical and a list develops, the ice must be
cleared from the lower side first. Bear in mind that any correction of the list of the
vessel by pumping fuel or water from one tank to another may reduce stability
during the process when both tanks are slack;
.10
when a considerable amount of ice forms on the bow and a trim appears, ice must be
quickly removed. Water ballast may be redistributed in order to decrease the trim;
MSC 85/26/Add.1
ANNEX 2
Page 94
.11
clear ice from the freeing ports and scuppers in due time in order to ensure free
drainage of the water from the deck;
.12
check regularly for water accumulation inside the hull;
.13
avoid navigating in following seas since this may drastically worsen the vessels
stability;
.14
register in the vessels log-book the duration, nature and intensity of ice
formation, amount of ice on the vessel, measures taken to combat ice formation
and their effectiveness; and
.15
if, in spite of all the measures taken to ensure the vessels endurance in conditions
of ice formation, the crew is forced to abandon the vessel and embark on
life-saving craft (lifeboats, rafts) then, in order to preserve their lives, it is
necessary to do all possible to provide all the crew with warm clothing or special
bags as well as to have a sufficient number of lifelines and bailers for speedy
bailing out of water from the life-saving craft.
List of equipment and hand tools
A typical list of equipment and hand tools required for combating ice formation:
.1
ice crows or crowbars;
.2
axes with long handles;
.3
picks;
.4
metal scrapers;
.5
metal shovels;
.6
wooden sledge-hammers;
.7
fore and aft lifelines to be rigged each side of the open deck fitted with travellers
to which lizards can be attached.
Safety belts with spring hooks should be provided for no less than 50% of the members of the
crew (but not less than 5 sets), which can be attached to the lizards.
Notes:
The number of hand tools and lifesaving appliances may be increased, at the
shipowners discretion.
Hoses which may be used for ice combating should be readily available
on board.
***

IMO2008 - MSC267 (85) - 2008 IS Code PDF

Uploaded by

Copyright:

Available Formats

IMO2008 - MSC267 (85) - 2008 IS Code PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

IMO2008 - MSC267 (85) - 2008 IS Code PDF

Uploaded by

Copyright:

Available Formats

MSC 85/26/Add.

Special criteria for certain types of ships

RECOMMENDATIONS FOR CERTAIN TYPES OF SHIPS AND

Recommended design criteria for certain types of ships

Guidance in preparing stability information

Stability calculations performed by stability instruments

Chapter 5 Operational provisions against capsizing

Considerations for watertight and weathertight integrity

Determination of lightship parameters

Recommendations for skippers of fishing vessels on ensuring

cargo ships carrying timber deck cargoes;

special purpose ships;

offshore supply vessels;

mobile offshore drilling units;

cargo ships carrying containers on deck and containerships.

operating conditions means conditions wherein a unit is on location for the

transit conditions means conditions wherein a unit is moving from one

Pontoon is considered to be normally:

carrying only deck cargo;

having a block coefficient of 0.9 or greater;

having a breadth/depth ratio of greater than 3; and

Dynamic stability phenomena in waves

Righting lever variation

Resonant roll in dead ship condition

Broaching and other manoeuvring related phenomena

Criteria regarding righting lever curve properties

Severe wind and rolling criterion (weather criterion)

under these circumstances, area b shall be equal to or greater than area a,

Figure 2.3.1 Severe wind and rolling

= gravitational acceleration of 9.81 m/s2.

The angle of roll (1)8 referred to in 2.3.1.2 shall be calculated as follows:

= factor as shown in table 2.3.4-1

= factor as shown in table 2.3.4-2

= 1.0 for round-bilged ship having no bilge or bar keels

= 0.7 for a ship having sharp bilges

= 0.73 + 0.6 OG/d

= mean moulded draught of the ship (m)

= moulded breadth of the ship (m)

= mean moulded draught of the ship (m)

CB = block coefficient (-)

GM = metacentric height corrected for free surface effect (m).

Table 2.3.4-2 Values of factor X2

Table 2.3.4-3 Values of factor k

(Intermediate values in these tables shall be obtained by linear interpolation)

B/d smaller than 3.5;

(KG/d-1) between - 0.3 and 0.5; and

SPECIAL CRITERIA FOR CERTAIN TYPES OF SHIPS

0.3 m above the seat in respect of seated passengers.

= service speed (m/s)

LWL = length of ship at waterline (m)

= mean draught (m)

KG = height of centre of gravity above baseline (m).

Oil tankers of 5,000 dwt and above

Cargo ships carrying timber deck cargoes

Alternative stability criteria

Cargo ships carrying grain in bulk

High-speed craft, as defined in section 2 (Definitions) of the Introduction, constructed on or

The purpose of this part of the Code is to:

provide guidelines for stability information, operational provisions against