AVESTA FinishOneTM Passivator 630 - Passivate Without Nitric or Citric Acid

Avesta FinishOne
Passivator 630
An acid-free passivator!
Avesta FinishOne Passivator 630 passivate without nitric
or citric acid. It helps to remove free iron from the surface and
regenerate the protective layer in the stainless steel by speeding
up the passivation process.
Standard applications
Avesta FinishOne Passivator 630 is intended for a wide range
of industrial passivating applications. It offers a good general
passivating result on stainless steel surfaces.
Features
Restores the passivation layer on stainless steel surfaces
that have been damaged during fabrication such as grinding, brushing, blasting etc or usage.
Improves the result after pickling by speeding up the passivation process.
Diminishes the risk of discoloured surfaces caused by flash

clouds or free iron (smut) when used wet-on-wet.
Reduces the formation of toxic nitric fumes during rinsing
after pickling.
Prevents water staining caused by poor rinse water.
Creates no hazardous waste and contains no nitric acid.
Is easy to handle and classified as non-dangerous goods.
Surface restoration
Avesta Cleaner 401 can be used together with Avesta FinishOne
Passivator 630, which helps regenerate the protective layer in the
stainless steel by speeding up the thickness of the passive layer.
Avesta FinishOne Passivator 630 helps speeding up the thickness of

the passive layer.
Instructions for use

1.
1.1 To avoid smut formation after spray

pickling, the passivator shall be applied
before rinsing while the surface is still
wet, wet on wet. Leave the fluid to
react 30 seconds.
1.2 To passivate after mechanical treatment,
first pre-clean the surface using Avesta
Cleaner 401, rinse with water, then
2.
3.
apply the passivator wet on wet, and

give it 35 min. to react.
1.3 To use for reduction of nitric fumes,
when pickling, spray it on as a mist over
the surface wet on wet.
2. Apply the Passivator with a spray pump,
e.g. Avesta Membrane Pump SP-25.
4.
3. Working time. See 1.

4. Rinse thoroughly with water. There is
no need to treat the waste water which
is neutral and acid-free. If a complete
residue free surface is needed make a
final rinse with deionized water.
Packaging
Waste treatment
Avesta FinishOne Passivator 630 is supplied in 2 kg, 25 kg

and 1000 kg IBC polyethylene containers.
Empty containers (HDPE) must be cleaned and can then be

recycled according to local regulations.
Storage
Other information
Avesta FinishOne Passivator 630 should be stored

indoors at room temperature. Containers must be kept
properly closed, in an upright position and inaccessible to
unauthorised persons.
For more information, please visit our website

www.avestafinishing.com where you can find Safety
Data Sheets and other useful information.
Keep the lid on at all times when not in use. Metals, alkaline, organic materials, heat and UV radiation will degrade
the product. Store in a clean, cool and UV protected environment. Avoid contact with textiles.
Worker safety
Protective clothing. In general users should wear acid-resistant overalls, gloves and rubber boots. Face visor should
be used and, if necessary, suitable respiratory protective
devices.
Special conditions may apply from one country to another.

Consult our website where updated Safety Data Sheets can
be found.
Avesta Finishing Chemicals
Lodgatan 14
SE-211 24 Malm, Sweden
Tel: +46 (0)40 28 83 00
Fax: +46 (0)40 93 94 24
www.avestafinishing.com
Good Chemistry at Work
Information given in this brochure may be subject to alteration without notice. Care has been taken to ensure that the contents of this publication are accurate, but Bhler Welding Group
Nordic AB and its subsidiary companies do not accept responsibility for errors or for information which is found to be misleading. Suggestions for or descriptions of the end use or application
of products or methods of working are for information only and the company and its subsidiaries accept no liability in respect thereof. Before using products supplied or manufactured by the
company the customer should satisfy himself of their suitability.
I10272-1EN ver 1, 2012.03 Wahlgren & Hansson
Bhler Welding Group Nordic AB

AVESTA FinishOneTM Passivator 630 - Passivate Without Nitric or Citric Acid

Uploaded by

Copyright:

Available Formats

AVESTA FinishOneTM Passivator 630 - Passivate Without Nitric or Citric Acid

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AVESTA FinishOneTM Passivator 630 - Passivate Without Nitric or Citric Acid

Uploaded by

Copyright:

Available Formats

Avesta FinishOne

Diminishes the risk of discoloured surfaces caused by flash

Creates no hazardous waste and contains no nitric acid.

Is easy to handle and classified as non-dangerous goods.

Avesta FinishOne Passivator 630 helps speeding up the thickness of

Instructions for use

1.1 To avoid smut formation after spray

apply the passivator wet on wet, and

3. Working time. See 1.

Avesta FinishOne Passivator 630 is supplied in 2 kg, 25 kg

Empty containers (HDPE) must be cleaned and can then be

Avesta FinishOne Passivator 630 should be stored

For more information, please visit our website

Special conditions may apply from one country to another.

Good Chemistry at Work

I10272-1EN ver 1, 2012.03 Wahlgren & Hansson

Bhler Welding Group Nordic AB

You might also like