ATS - EnG

Sices ATS control panel is designed for mains/genset transfer switch applications that
involve a genset usually equipped with an automatic control panel. The ATS control panel
comprises all circuits, devices and controls, which enable the switch between the mains
and the genset, in order to supply the load in case of mains failure.
The ATS control panel is made with a steel sheet subjected to a painting treatment using
high resistance epoxy powder. The power circuit is safety split from the control area in
accordance to the main operation rules.
Multiple voltage
230/380/400/440V
The grade protection is IP20 with opened door. With closed door, it is IP40 for the BASIC
version and IP54 for the LOGICA version. IP55 is also available on demand.
Double frequency 50/60Hz

BASIC and LOGICA version
From 45A up to 4000A
Attractive price
Used by the greatest
genset companies
According to the power of the genset, the power circuit is composed by a couple of
interlocked contactors (up to 125A included) or by a motorized changeover switch, in both
cases 4 poles.
In addition, there is a version of ATS with power circuit composed by two automatic,
interlocked and motorized circuit breakers.
Starting from 160A, SICES ATS Control panels have MULTIPLE VOLTAGE and
MULTIPLE FREQUENCY.
Perfect for Dual Gensets

operations
Made in Italy
IS0 9001 certified
The voltages available are: 230/380/400/440V

Frequency: 50/60Hz
BASIC
VERSION
LOGICA
VERSION
Power Terminal board Mains/

Genset/Load
YES
YES
Selector switch
Mains Automatic 0 Genset
YES
NO
Keyboard with push buttons for

the mode/control selection
NO
YES
Optical signal with lamp/led to

advise the load is supplied by
the Mains
YES
YES
Optical signal with lamp/led to

advise the load is supplied by
the Genset
YES
YES
Fuses for protections
YES
YES
Adjustable three-voltage relay

Mains and Genset voltage
NO
YES
Microprocessor controller
NO
YES
Voltmeter for Mains voltage:

Phases L1-L2/L2-L3/L1-L3
NO
YES
Mains and Genset frequency

meter
NO
YES
Battery voltage meter
NO
YES
Working hour meter
NO
YES
Current transformers for the activation of currents, power and

cosfi measurement
NO
OPTION (*)
Automatic battery charger
NO
OPTION
Features:
BASIC VERSION: Its a manual ATS Control panel without

microprocessor-based controller, equipped with a 4 positions
switch selector with AUTOMATIC 0 MAINS GENSET and
lamps for optical signalling Load supplied by the Mains and
Load supplied by the Genset. Fuses, protections and terminal
boards are available as well. This type of ATS panel is usually
combined to a local genset control panel.
LOGICA VERSION: Its an automatic ATS Control panel
equipped with microprocessor-based controller with graphic
display that allows to show voltages, frequency, working hours
and the battery voltage of the genset. This type of ATS panel is
particularly suggested in combination to gensets with semiautomatic controllers that require an external contact to start
(e.g. Caterpillar, FG Wilson, Cummins, etc. gensets).
The LOGICA ATS panel supports a microprocessor-based
controller, available in two versions: ATS115 and ATS115
Plus
As option, its possible to add 3 CTs in order to enable the

current and power measure and the cosfi.
(*) Request to SICES SRL ([email protected])

ATS Control panel
Genset control panel
START Engine start push-button

STOP Engine stop push-button
ACK Acoustic alarm silencing push-button
UP/DOWN push-buttons for the display selection
MCB push-button
GCB push-button
N.4 ARROW keys for LCD display selection mode, window
selection, parameter change and other
EXIT and ENTER keys
SHIFT key
Operation panel and LEDs for the signalisation and selection
of the operation modes: off/reset/program, manual,
automatic, alarms/warnings, aux., mains live, genset live, etc.
Mains Voltage
L1-N, L2-N, L3-N, L1-L2, L2-L3, L3-L1
True measure calibrated to RMS.
Lx-N max. voltage < 300Vac cat. IV
High voltage pulse = 6kV 1.2/50 us
Max. measurable voltage = 25.000V (by external TV).
Generator Voltages
L1-N, L2-N, L3-N, L1-L2, L2-L3, L3-L1
True RMS measure.
Lx-N max. voltage < 300Vac cat. IV
High voltage pulse = 6kV 1.2/50 us
Max. measurable voltage = 25.000V (by external TV).
Generator Currents (Op t i o n al i n c as e ad d i t i o n al
current transformers)
L1, L2, L3, N
True RMS measure.
Nominal max. current: 5Aac
Overload measurable current : 4 x 5Aac (sinusoidal).
Internal current transformer.
Max. nominal current = 6000A (by external TA).
Generator and Mains Frequency meter
Resolution = 0.1 Hz.
Accuracy = 50ppm, 35ppm/C (typical)
Battery Voltmeter
Resolution = 0.1V
A set of high efficiency LEDs are used to inform on the

current status of the Mains and of the Genset and for the
visualization of any alarm. Secondary alarms are
represented by their corresponding display code.
Status and signalling
Source A live (Mains or Genset)
Source B live (Mains or Genset)
Source A circuit breaker closed
Source B circuit breaker closed
Start/Stop Source A or B
Remote start
Battery fault (Max/Min voltage)
Max. controller temperature

Emergency stop
Clock not configured
Protections
Genset X not stopped
Genset X out limit
Source A or B operating mode not reached
Phase sequence failure on Source A or B
Source A or B failure
Source A or B circuit breaker stopped
Source A or B circuit breaker open
Additional indications are available to display measures
and cumulative alarms.
N.1 USB Port for the configuration of parameters

As option:
Use of the ATS115Plus controller equipped with:

N.1 RS232 Serial port Modbus RTU
N.1 RS485 Serial port Modbus RTU
N.1 RJ45 Ethernet Serial port Modbus TCP/IP
Direct management of a PSTN and GSM modem
GSM/GPRS/GPS Modem
Optional circuits available:
Addition of a battery charger 5A 12/24Vdc
Addition of 3 CTs on the output
Dual Genset operation for the automatic switch of the two
gensets
Engine diagnostic codes

Periodic test
Clock and History log
Remote start and stop
Alarm horn
Different levels of password for the correct configuration of
the parameters
Graphic display 70x38 mm - 128x64 pixel
LCD display with LEDs
Multilanguage display: IT, EN, FR, RU, ES, PT/BR
Current
Dimensions
HxLxD mm
Weight
45A
600x400x200
25Kg
70A
600x400x200
25Kg
100A
600x400x200
25Kg
125A
600x400x200
25Kg
160A
1000x600x250
30Kg
250A
1000x600x250
56Kg
400A
1000x600x300
60Kg
630A
1000x600x400
90Kg
800A
1000x600x400
100Kg
1000A
1900x800x600
245Kg
1250A
1900x800x600
245Kg
1600A
1900x800x600
275Kg
2000A
1900x1000x800
335Kg
2500A
1900x1000x800
390Kg
3150A
1900x1000x1000
500Kg
4000A
1900x1000x1000
600Kg
Supply voltage: 230 400 Vac (others to be specified)

Available also multiple voltage version: 220/380/400/440V
Auxiliary voltage: 12 Vdc or 24 Vdc
Frequency: 50 Hz or 60 Hz
The electric diagrams are available in double language,
choosing among: EN, FR, IT, PT, ES.
Insulation: > 50 Mohm
Dielectric strength AC: 2500V/1'
Dielectric strength DC: 1000 V/1'
Level of protection: IP40 (BASIC version) or IP54
(LOGICA version)
Colour: RAL 7035
Ambient temperature: - 20 to + 70 C
Compliance to CEI IEC EN rules:
2006/95/CE LOW VOLTAGE DIRECTIVE
2004/108/CE EMC DIRECTIVE
93/68/CEE CE STAMP REGULATION
The ATS panel is designed and manufactured in
compliance with the ISO9001 certification

ATS - EnG

Uploaded by

Copyright:

Available Formats

ATS - EnG

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ATS - EnG

Uploaded by

Copyright:

Available Formats

Sices ATS control panel is designed for mains/genset transfer switch applications that

Double frequency 50/60Hz

Perfect for Dual Gensets

The voltages available are: 230/380/400/440V

Power Terminal board Mains/

Keyboard with push buttons for

Optical signal with lamp/led to

Optical signal with lamp/led to

Fuses for protections

Adjustable three-voltage relay

Voltmeter for Mains voltage:

Mains and Genset frequency

Battery voltage meter

Working hour meter

Current transformers for the activation of currents, power and

Automatic battery charger

BASIC VERSION: Its a manual ATS Control panel without

As option, its possible to add 3 CTs in order to enable the

(*) Request to SICES SRL ([email protected])

Genset control panel

START Engine start push-button

A set of high efficiency LEDs are used to inform on the

Max. controller temperature

N.1 USB Port for the configuration of parameters

Use of the ATS115Plus controller equipped with:

Engine diagnostic codes

Supply voltage: 230 400 Vac (others to be specified)

You might also like