Line Sizing Spreadsheet Comparison
Line Sizing Spreadsheet Comparison
CPECC Spreadsheet.
Compare this section against the CH2MHill
spreadsheet
Calculation Sheet
SECTION NO.
FROM:
TO:
PROCESS CONDITIONS:
Pressure (barg)
Temperature C
Phase (V/L/M)
VAPOUR:
Mass flow rate (kg/hr)
Density (kg/m)
Viscosity (cP)
(Vapour Only) Compressability
(Vapour Only) Mol. Wt
LIQUID:
Mass flow rate (kg/hr)
Density (kg/m)
Viscosity (cP)
0.240
92
0.112
92
3.800
92
3.781
92
3.703
92
510400
218900
218900
510400
656700
1100.0
0.60
1100.0
0.60
1100.0
0.60
1100.0
0.60
1100.0
0.60
12
LINE SPECIFICATION:
Nominal Pipe Size (in)
12
10
12
Pipe Schedule
11
11
11
11
Pipe ID (in)
User input I.D
12
10
10
12
12
2
0.00016
2
0.00016
2
0.00016
2
0.00016
2
0.00016
17
5/29/2010
5
9
3
2
12
4
4
23
5
2
35
6
4
Material
Roughness
Line Type (S/D/P)
PIPE FITTINGS
Length (m)
Elbows
90 Elbow Standard (R/D = 1), screwed
90 Elbow Standard (R/D = 1), flanged/welded
90 Elbow Standard (R/D = 1.5), all types
90 Mitred elbow (R/D =1.5) 1 Weld 90 angle
90 Mitred elbow (R/D =1.5) 2 Weld 45 angle
90 Mitred elbow (R/D =1.5) 3 Weld 30 angle
90 Mitred elbow (R/D =1.5) 4 Weld 22.5 angle
90 Mitred elbow (R/D =1.5) 5 Weld 18 angle
45 Elbow Standard (R/D=1) all types
45 Elbow Long-radius (R/D=1.5) all types
45 Elbow Mitred, 1 Weld , 45 angle
45 Elbow Mitred, 2 Weld , 22.5 angle
180 Standard (R/D=1), screwed
180 Standard (R/D=1), flanged/welded
180 Long radius (R/D=1.5), all types
Branch tees
Tee (used as elbow) standard, screwed
Tee (used as elbow) Long-radius, screwed
Tee (used as elbow) swept, branch
Tee (used as elbow) standard, flanged/welded
Tee (used as elbow) stub-in-type branch
Straight tees
Tee (run through tee) standard, screwed
Tee (run through tee) standard, flanged/welded
Tee (run through tee) stub-in-type branch
Valves
Gate Valve,full line size
Ball valve, reduced trim = 0.9
Plug valve, reduced trim = 0.8
Globe valve, Standard
Globe valve, angle or Y-type
Diaphragm valve, dam type
Butterfly valve
Check valve, Lift
Check valve, Swing
Check valve, Tilting-disc
No. of Reducers/Expansions
Reduced/Enlarged pipe NB. (in)
Flow into pipe
Exit from pipe
Other velocity heads
Static head gain (-ve)/loss (+ve) (m)
0.11
0.085
3.781
3.703
3.383
11
11
11