Ref Compressor HASEEGAVA PDF

VK / VKL
REFRIGERATION COMPRESSOR
OPERATION, DATA & MAINTENANCE
MANUAL
Ver. 1
HASEGAWA
CONTENTS
Preface
Safety Instructions & Guidelines
1. INTRODUCTION
1.1. Construction
1.2. Models
1.3. Operational limits
1.4. Specifications, Capacity and Power
6
8
9
10
2. OPERATION
2.1.
2.2.
2.3.
2.4.
2.5.
2.6.
2.7.
2.8.
2.9.
Introduction
11
Preparation for operation

Compressor starting
Operational and inspection criteria
Compressor shutdown
Extended period of shutdown
Operation of compressor prior and post maintenance
Actions to prevent liquid carry-over
Fault diagnosis and rectification chart
Pressure vs. Condensing Temperature and Evaporating Temperature
12
12
13
14
14
15
15
17
21
3. CONSTRUCTION, MAINTENANCE and INSPECTION

3.1.
3.2.
3.3.
3.4.
Preparation
Precautions
Maintenance schedule
Maintenance Procedures (M.P.):
M.P. 1 Cylinder Head Cover
M.P. 2 Suction and Discharge Valves
M.P. 3 Piston and Piston Rings
M.P. 4 Cylinder Liner
M.P. 5 Unloader Assembly
M.P. 6 Mechanical Seal Assembly
M.P. 7 Front Bearing
M.P. 8 Oil Pump
M.P. 9 Rear Main Bearing
M.P. 10 Crankshaft
M.P. 11 Oil Pressure Regulating Valve
M.P. 12 Oil Return Valve
M.P. 13 Oil Screen & Oil Filter
M.P. 14 Oil Cooler
M.P. 15 Crankcase Heater
M.P. 16 Suction Gas Strainer
M.P. 17 Safety Valve, Pressure Gauge and Pressure Switch
M.P. 18 V-Belt Drive
M.P. 19 Coupling - Direct Drive
M.P. 20 Flanged Motor
22
22
22
25
27
30
35
36
40
42
44
47
49
51
52
53
55
57
58
59
60
61
63
HASEGAWA
PREFACE
Hasegawa Refrigeration Ltd. is a specialized manufacturer of refrigerating machines and equipment,
having been established in 1910.
Hasegawa Refrigeration Ltd. manufactured the first High-speed, Multiple cylinder Compressor in
Japan, establishing a sound reputation through dynamic achievement in the domestic and global
markets.
Hasegawa Refrigeration Ltd. manufactures exceedingly efficient compressors to comply with market
demands, utilizing Hasegawas vast experience, advanced manufacturing techniques and materials.
Therefore Hasegawa is able to supply worldwide, from its modern manufacturing facility the most
advanced series of High-speed, Multiple cylinder compressors.
This manual provides the operator and maintenance technician the necessary information to operate
the compressor efficiently and maintain the compressor economically. Hasegawa is confident that our
compressors will exceed your requirements and achieve a high degree of product satisfaction.
In the event that technical assistance or information is required on VK compressors, please have the
following information available when contacting Hasegawa Refrigeration Ltd:
1.
2.
3.
4.
5.
6.
7.
8.
Compressor serial number

Compressor model number
Type of system
Operating conditions
Suction pressure & temperature
Intermediate pressure & temperature (if applicable)
Discharge pressure & temperature
Oil differential pressure
Motor current full and partial load
Run hours
Compressor rpm
Motor HP
Refrigerant type
Any other relevant information
Hasegawa Refrigeration Ltd. provides

the information enclosed as a guide and
is subject to periodic revision.
HASEGAWA
SAFETY INSTRUCTIONS & GUIDELINES
INTRODUCTION
Thank you for selecting the HASEGAWA reciprocating compressor unit. The compressor is provided
complete with a HASEGAWA SURELY trademark and is supplied with the standard HASEGAWA
limited warranty.
This leaflet explains the safety instructions and guidelines associated with the operation and
maintenance of HASEGAWA reciprocating compressors. Prior to operating or performing equipment
inspection and maintenance procedures on HASEGAWA reciprocating compressors, these instructions
must be comprehended and complied with unless superceded by local codes or regulations.
Follow the safety instructions and guidelines carefully to prevent personal or fatal injury during the
operation and maintenance of HASEGAWA reciprocating compressors.
DISCLAIMER
HASEGAWA does not accept responsibility for personal or fatal injuries caused by unauthorized
modification, the use of non-genuine components, or operation and maintenance of HASEGAWA
reciprocating compressors not performed in accordance with the following guidelines.
The following flags denote the level of caution to be adhered to:
Warning
Incorrect equipment operation or handling may cause serious injury or possibly death.
Attention
Incorrect equipment operation or handling may cause personal injury or equipment
damage.
Warning
Refrigeration service personnel with the appropriate level of training, qualifications and
knowledge may only be authorized to undertake equipment operation, inspection and
maintenance.
Remain at a safe distance from operational equipment. Do not operate the compressor with the
fixed belt or coupling guard removed, or attempt to inspect V- belts while the compressor is in
operation.
Stop the compressor prior to inspection. Use the appropriate lock out / tag out method to
prevent inadvertent compressor manual or remote automatic start up.
Electrical service personnel with the appropriate level of training, qualifications and knowledge
may only be authorized to undertake electrical repairs or modifications.
4
Use the appropriate lock out / tag out method prior to opening electrical service panels or
controls to ensure electrical isolation of the equipment.
Follow the appropriate local codes of practice and regulations at all times while undertaking
mechanical or electrical maintenance procedures.
Attention
General
Do not utilize or install any components, equipment or materials that are not compatible with the
system.
Operation
In the event of uncharacteristic indications, stop the compressor immediately. Continued operation
of the compressor with abnormal indications can result in personal injury or equipment damage.
Should the compressor be stopped due to uncharacteristic indications, investigate and repair the
problem prior to restarting the compressor.
Do not operate the compressor beyond the design specifications and limits.
Remain at a safe distance from the compressor driving system when the compressor is operational
or set for remote automatic control.
Do not remove the fixed belt or coupling guard while the compressor is operating or set for remote
automatic control as personal injury may occur.
Do not remove plugs or open service valves while the compressor is operating or set for remote
automatic control, as leakage of high-pressure (high temperature) refrigerant gas or lubricating oil
will occur. This would result in personal injury or equipment damage.
Daily Inspection & Maintenance
Qualified, trained and authorized personnel must complete operation, inspection and maintenance
tasks.
Note
Service personnel should keep these safety instructions and guidelines adjacent to the compressor,
in a place that is both safe and accessible.
Adherence to these safety instructions and guidelines is mandatory, unless superceded by local
codes and regulations.
HASEGAWA
1. INTRODUCTION
1.1 Construction
The Hasegawa SURELY compressor is designed and manufactured for use with refrigerants R717,
R22 and HFCs. The compressor is shipped only after completing leak and performance testing to strict
Hasegawa procedures and regulations.
The fundamental principals of design and manufacture of Hasegawa compressors are:
Large capacity,
Compactness,
Lighter weight and
Ease of handling.
These principals have been attained with many years of compressor design and operational experience,
being instigated by means of close collaboration with existing and prospective customers.
Crankcase, Cylinder Covers and Principal Components

Are manufactured from high-grade cast iron and are precisely machine finished to Hasegawa
specifications.
Cylinder Liners
Are manufactured from high grade, exceptional wear-resistant cast iron to exact tolerances and
polished for extended durability.
Pistons
Are manufactured from precision cast heat-treated aluminum alloy, for a lighter and stronger
reciprocating mass. The pistons have passages for oil transfer, which allow for superior wear
resistance and seizure protection with cylinder liners.
Piston Rings
Are manufactured from high grade cast iron and are fitted as three rings per piston:
1. Compression ring chrome plated.
2. Compression ring and oil control ring.
3. Oil scrapper ring.
These rings are specifically designed and manufactured for exceptional oil control efficiency
for long periods, resulting in minimal oil consumption.
Piston Pins
Are manufactured from high-grade alloy steel for enhanced hardness, roundness and face
accuracy, as the pins are super-finished after the hardening process.
Piston Pin Plain Bearings

Are steel-backed bronze bushes.
Piston Pin Needle Roller Bearings

Are installed in the high side of a two-stage compressor. The piston pins are common to both
high and low sides of a compressor.
Connecting Rods
Are manufactured from heat treated forged aluminum alloy designed with high rigidity and
minimal weight, thus combined with the piston ensuring minimum vibration and ease of
maintenance.
Crankshaft
Is heat-treated to ensure wear-resistance and fatigue strength. Special high-frequency
induction heating, a process developed by Hasegawa, hardens the crank pin sections.
Crank Pin Bearings

Are steel-backed white metal split sleeves manufactured to exact tolerances with a mirror-like
finish.
Main Bearings
Are manufactured by centrifugal casting metal alloy to a highly rigid steel liner and are
machined to exact tolerances. The front bearing is inserted into the crankcase and is held in
position by bolts; the rear bearing is set into the rear (oil pump) housing, which is bolted to the
crankcase. These bearings can be removed, inspected and refitted without the need to remove
the crankshaft or piston assemblies.
Oil Pump
Of the trochoid gear type with an automatic reversible rotating mechanism for ease of
compressor installation, high efficiency, stable operation and long life.
Oil Pressure Regulating Valve

The valve is fitted to the rear of the compressor on the rear housing and is used for obtaining
the correct oil pressure.
Oil Lubrication System

Oil, filtered through a suction screen located in the lower portion of the crankcase sump is
drawn up and pressurized by the oil pump and is fed into the front bearing after being cooled
and filtered. From the front bearing oil is fed internally through the crankshaft to lubricate the
crank pin bushings and internally through connecting rod oil passageway to lubricate the
piston pin bearings.
Mechanical Shaft Seal

Spring loaded synthetic rubber bellows type for compensation of crankshaft float.
Suction Gas Strainer

A screen located in the suction inlet manifold (single stage compressor), or inlet housing (x 2
compound compressor) filters refrigerant gas.
Suction and Discharge Valve Plates

Are manufactured to high specification by heat-treating and lap finishing the stainless steel
utilizing the process of vacuum refining to ensure extensive durability.
Safety Heads
Ensure, in the event of liquid refrigerant or oil carry-over that abnormal pressure is not created
within the cylinders by unseating and directing the flow to discharge. The safety head
combines the discharge valve plate, inner valve seat and valve guide are assembled with the
outer seat which is held in place by a single spring under the cylinder cover.
Unloader Mechanism
Piston type, acting under pressure or bleed from the lubricating oil supply to load or unload a
bank of pistons. The piston plate rotates cam rings, which lower or raise the suction valve
plate to load or unload a bank of pistons.
High and Low Pressure Switches

Are to protect the compressor by interrupting electrical power to the motor in the event of
abnormal high or low pressure.
Oil Protection Switch

Ensures that, should the oil differential pressure decrease below a set point then electrical
power to the motor is interrupted and the compressor will stop. The differential pressure is
calculated between the crankcase pressure and oil pressure, the switch having an in-built delay
of approximately 45 seconds to prevent nuisance tripping.
Safety Relief Valve

Protects the compressor from excessive internal pressure and relieves to atmosphere, or
alternatively to the system low side. Should excessive pressure be designed to be relieved to
the low side, then relief piping to a point as remote as possible from the compressor is
required to prevent superheating of the gas by repeated compression.
Driving Method
Land based compressors are capable of being driven by v-belts, direct coupled using a flexible
coupling or constructed with a flange that permits the motor to be mounted on the crankshaft
and bolted directly to the compressor. Marine type compressors are constructed with a flange
that permits the motor to be mounted on the crankshaft and bolted directly to the compressor.
RM Compressor Motor
The squirrel cage rotor is specifically designed for the flanged type application and mating
with the Hasegawa compressor ensuring high efficiency at full and partial loads. Maintenance
of the compressor mechanical seal is accomplished by removing the rotor but leaving the
motor casing mounted to the compressor.
1.2 Models
The VK compressor range is divided into two distinct categories, namely land and marine,
which comprise both single stage and compound compressors.
Single Stage Compressor

Used for comparatively higher evaporating temperature, above -22F (-30C) and comprising
the following models: VK4, VK6, VK8, VKL4, VKL6 and VKL8.
Compound Compressor
The crankcase is internally divided into low and high stages; so as to enable two- stage
compression by one compressor and is used for temperatures below -22F (-30C). This
compressor range is comprised of the following models: VK31, VK42, VK62, VKL31,
VKL42 and VKL62.
Nomenclature
The model number, refrigerant type and application (marine) identify each compressor, in
addition to the serial number. Therefore a typical compressor would be identified as follows:
1. Serial number:
VK(L)_ _ _ _ _ _
8
2.
Model number: VK(L)42RM

Where R is the refrigerant type, i.e. R22 (other letters apply to different refrigerants and
comply with international standards) and M is the flanged motor application.
These compressors comprise a considerable number of common and interchangeable

components, which permit spare parts inventory to be kept to a minimum.
1.3 Operational Limits

VK compressors should not be operated beyond the following limits:
Compressor RPM
Max. = 1800 rpm
Min. = 980 rpm
Compression ratio*
Max. = 15
Target Max: < R717 10, R22 - 11
Pressure difference
Max. = 227 psi
(16.47 kg/cm) [1.6MPa]
Suction pressure
Single stage compressor
Max. 76 psig
(C.S.T: R717 = 50F, R22 = 45F, R134a = 78F)
Max. 0.54 MPaG (C.S.T: R717 = 10C, R22 = 7C, R134a = 25C)
Min. 0 psig
(C.S.T: R717 = -31F, R22 = -40F, R134a = -22F)
Min. 0 MPaG
(C.S.T: R717 = -35C, R22 = -40C, R134a = -30C)
Two stage compressor
Max. 28 psig
(C.S.T: R717 = 14F, R22 = 5F)
Max. 0.2 MPaG (C.S.T: R717 = -10C, R22 = -15C)
Min. 11 psig
(C.S.T: R717 = -76F, R22 = -94F)
Min. 0.08MPaG (C.S.T: R717 = -60C, R22 = -70C)
RM type compressor
Max. Determined by motor capacity.
Min. 11 psig
(C.S.T: R22 = -94F)
Min. 0.08MPaG (C.S.T: R22 = -70C)
Discharge pressure
Below: 255 psig (R717) 312 psig (R22)

1.8 MPaG (R717) 2.2 MPaG (R22)
When compression ration is high, temperature of discharge gas should
be less than 150C / 302F (R717), 120C / 248F (R22).
Oil Pressure
Max. = 114 psig
Min. = 28 psi Differential
Max. = 8kg/cm2G
Min. = 2kg/cm2 Differential
Oil Temperature
Min. = 59F
Max. = 140F
Min. = 15C
Max. = 60C
Normal operation = 55C
Normal operation = 131F
*Compression ratio = Absolute discharge pressure / Absolute suction pressure, for each stage.
Do not have parallel operation of single and two stage compressors on the same suction line.
1.4 Specification, Refrigeration Capacity and Required Power

Single Stage Compressor
Model
Cylinders
RPM (Max)
Bore In.(mm)
Stroke In. (mm)
Unloading Steps
Suction In. (mm)
Disc. In. (mm)
Weight Lbs. (kg)
Oil US gal. (Ltrs)
VK4
VK6
VK8
VKL4
VKL6
VKL8
4
1800
3.35 (85)
2.75(70)
4-2
2
1 (40)
1060
(480)
1.72 (6.5)
6
1800
3.35 (85)
2.75(70)
6-4(2)(0)
2 (65)
1 (40)
1060 (480)
8
1800
3.35 (85)
2.75(70)
8-6(4)(2)(0)
3 (80)
2 (50)
1148 (520)
4
1800
3.35 (85)
3.35 (85)
4-2
2
1 (40)
1060 (480)
6
1800
3.35 (85)
3.35 (85)
6-4(2)(0)
2 (65)
1 (40)
1060 (480)
8
1800
3.35 (85)
3.35 (85)
8-6(4)(2)(0)
3 (80)
2 (50)
1148 (520)
1.72 (6.5)
1.85 (7)
1.72 (6.5)
1.72 (6.5)
1.85 (7)
Compound Compressor
Model
Cylinders
RPM (Max)
Bore In.(mm)
Stroke In. (mm)
Unloading Steps
Suction In.
(mm)
Disc. Low Stage
In. (mm)
Suc. High Stage
In. (mm)
Discharge In.
(mm)
Weight Lbs. (kg)
VK31
3+1
1800
3.35 (85)
2.75(70)
3-1
2 (65)
VK42
4+2
1800
3.35 (85)
2.75(70)
4-2(0)
2 (65)
VK62
6+2
1800
3.35 (85)
2.75(70)
6-4(2)(0)
3 (80)
VKL31
3+1
1800
3.35 (85)
3.35 (85)
2 (65)
VKL42
4+2
1800
3.35 (85)
3.35 (85)
4-2(0)
2 (65)
VKL62
6+2
1800
3.35 (85)
3.35 (85)
6-4(2)(0)
3 (80)
1(32)
1(32)
1 (40)
1(32)
1(32)
1 (40)
1(32)
1(32)
1 (40)
1(32)
1(32)
1 (40)
1 (25)
1 (25)
1(32)
1 (25)
1 (25)
1(32)
1080
1080
1268 (530)
1080
1080
1268
(490)
(490)
(490)
(490)
(530)
Oil US gal (Ltrs) 1.72 (6.5) 1.72 (6.5)
1.85 (7)
1.72 (6.5) 1.72 (6.5)
1.85 (7)
Capacity control in ( ) is optional, for RM AM compressors standard for starting.
Weight of compressor only, not including base, flywheel (coupling) or motor.
RM, AM Type Motor

Rated
Output
BHP(kw)
25 (18)
30 (22)
40 (30)
50 (37)
60 (45)
75 (60)
20 (15)
25 (18)
30 (22)
40 (30)
50 (37)
60 (45)
Rated speed (rpm)

Type
Drip-proof
Squirrel
Cage Rotor
Flanged
50 Hz
60Hz
1450
1450
1450
1450
1450
1450
980
980
980
980
980
980
1750
1750
1750
1750
1750
1750
1170
1170
1170
1170
1170
1180
Voltage
Pole
4
4
4
4
4
4
6
6
6
6
6
6
50 Hz
60 Hz
200/400
200/400
200/400
200/400
200/400
200/400
200/400
200/400
200/400
200/400
200/400
200/400
220/440
220/440
220/440
220/440
220/440
220/440
220/440
220/440
220/440
220/440
220/440
220/440
Insulation
10
HASEGAWA
2. OPERATION
Introduction
To ensure compressor optimum and efficient operation a full understanding of the compressor and
refrigeration system are required. A qualified technician, with the appropriate level of training to
complete system adjustments therefore guarantee the design operating parameters are achieved must
undertake initial system start-up.
The following fundamental guidelines are to be utilized to ensure the start-up procedure is completed
trouble free and may be used for manual or automatic operation of the compressor. Prior to start-up on
a new installation an appropriate vacuum test is to be carried out after which oil charging may be
undertaken. These guidelines are not exhaustive and are designed for use by a technician with the
appropriate training.
The following points cover basic operation and must be closely adhered to:
1. Hand turning
Prior to initial start-up and after a long period of standstill the

compressor must be hand turned to ensure a positive supply of
lubricating oil.
2. Oil charging
The compressor must be charge with oil to the correct quantity after
the final vacuum test. Operation of the compressor without oil is
prohibited.
Initial charging should be made through the oil charge inlet, located in
the side cover.
3. Air compression
Air compression must be avoided, with the exception of post

maintenance air purging undertaken for a few seconds.
Air compression for the purpose of leak testing etc is prohibited.
Operation of the compressor while structurally / mechanically
incomplete is prohibited.
4. V belt
Sheaves are to be correctly aligned and belts are to be correctly

tensioned prior to start-up. Further checks are to be completed as belts
stretch after initial use.
Do not over-tighten belts as damage to the mechanical seal may result.
5. Dust
Prior to pressure / vacuum testing cotton cloth is to be wrapped around

each gas suction strainer and secured in place with steel wire. Due to
the characteristics of some refrigerants acting as solvents, scale and
other debris is prevented entering the compressor preventing rapid
wear or failure. This cloth must be examined and if required, replaced
at the first and subsequent oil changes to ensure system cleanliness.
6. Oil return valve
The oil return valve of a compound compressor must be fully closed

during operation except for a few seconds periodically to ensure oil
drains from the high-side casing.
11
2.1 Preparation for Operation

1. Perform a thorough check of the system piping and connections for correct routing and integrity.
2. Confirm that an adequate volume of cooling water is circulating the condenser, compressor and oil
cooler for water cooled systems.
3. Confirm that the initial oil charge has been completed.
4. Turn the compressor by hand for several revolutions and confirm oil level is above half the sight
glass. Replenish as required.
5. Confirm the electro-mechanical sequence of operations and correct motor rotation.
6. The following valves must be placed in the fully open position:
Compressor discharge stop valve (both high and low on compound compressor).
Compressor bypass stop valve (if fitted).
Compound compressor suction stop valve.
Two-stage system intercooler inlet and outlet valves (only if separated from liquid cooler).
Evaporator suction valve (if fitted).
Safety relief, stop valve.
Pressure gauge stop valves (to be partially open).
Condenser inlet and outlet valves.
Liquid receiver inlet and outlet valves.
Condenser / receiver pressure equalizing valve.
7. The following valves must be placed in the fully closed position:
Compressor suction stop valve (low side only for compound compressor).
Oil separator, oil return line stop valve.
Liquified refrigerant cooler inlet and outlet valves (to be opened when parallel operation with
other compressor).
2.2 Starting
1.
2.
3.
4.
5.
6.
7.
8.
When the items in 2.1 above have been confirmed as correct, then the compressor may be started.
Close attention is required to the following:
Switch on the electric motor and start the compressor in an unloaded configuration.
Open gradually the suction stop valve and monitor for oil or liquid carry-over (excessive
mechanical noise safety springs or oil foaming) and monitor motor current draw.
Confirm the oil pressure and adjust as required to obtain the correct differential pressure by
adjusting the regulating valve. Should the compressor be shut down by the action of the oil
pressure switch, then conduct a thorough investigation as to the nature of the fault and rectify.
Repeated starting of the compressor by operation of the reset button is prohibited.
Set each valve to the correct position incrementally.
Perform the following checks and document the observations at regular intervals:
Current and voltage
Suction pressure
Intermediate pressure (as required)
Discharge pressure
Oil pressure
Oil level (replenish as required)
Set unloader control valves to obtain the correct operational condition and monitor operating
parameters as in 5 above. Allow 5 minutes between unloader operations.
Monitor the compressor for abnormal noise or vibration.
Open oil separator oil drain valve.
12
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
For RM type compressors, when the items in 2.1 above have been confirmed as correct then the
compressor may be started. Close attention is required to the following which is a method using a
star-delta motor as the preferred type:
Compressor shall be fully unloaded prior to start.
Switch on the electric motor and start the compressor on STAR.
Remain in this mode until the ampere draw falls to half the rated value. This will take
approximately 30 seconds when the suction pressure is 70 psig (5Kg/cm [0.5Mpa]) and a further
8 seconds to achieve 0 psig. (0Kg/cm [0Mpa]).
At this point switch from STAR to DELTA and simultaneously open fully the discharge bypass valve.
Gradually open the suction valve and monitor the compressor for abnormal mechanical noises and
oil foaming.
Gradually load the compressor and monitor the current draw to ensure the motor is not overloaded.
Confirm the oil pressure and adjust as required to obtain the correct differential pressure by
adjusting the regulating valve. Should the compressor be shut down by the action of the oil
pressure switch, then conduct a thorough investigation as to the nature of the fault and rectify.
Repeated starting of the compressor by operation of the reset button is prohibited.
Adjust as required the expansion valves to the oil cooler and gas cooler.
Open inlet and outlet valves and adjust the expansion valve of the liquid cooler.
Perform the following checks and document the observations at regular intervals:
Current and voltage
Suction pressure
Intermediate pressure (as required)
Discharge pressure
Oil pressure
Oil level (replenish as required)
Set control valves to obtain the correct operational condition.
Monitor the compressor for abnormal noise or vibration.
Open oil separator oil drain valve.
2.3 Operational and Inspection Criteria

During operation of the compressor data must be collected either manually or electronically and
checked against previous data for abnormalities to establish a preventative maintenance program.
The following items should form the basis for data recording:
1. Operation hours.
Record the duration of operation for each compressor.
2. Suction, discharge and if applicable intermediate pressures.
Close attention must be paid to the suction and discharge pressures, which are the basis of
performance for the compressor and refrigeration system, by which abnormalities can be observed.
3. Oil pressure.
The following values are the standard operating ranges for oil pressure.
Oil protection switch
Compressor
Minimum pressure 22 psi (1.5kg/cm)

Oil pressure = Suction pressure + Differential pressure
Differential pressure to be set by the oil pressure regulating valve in the following range: 28 to 35 psi
(2 to 2.5 kg/cm).
4. Oil temperature.
Maximum oil temperature +140F (+60C). Target oil temperature +131F (+55C).
5. Suction and discharge temperature.
13
6.
7.
8.
9.
10.
18 to 36F (10 to 20C) of superheat is recommended for suction temperature.

Discharge temperature should not be abnormally high.
Oil quantity.
Maximum level 2/3 sight glass.
Minimum level 1/3 sight glass, replenish to normal level.
Extreme care must be taken to prevent oil over-replenishment, as excessive consumption will
result.
Accurate recording of oil changes and replenishments is required to ascertain the quantity of oil
consumption.
Excessive oil consumption may be a function of liquid carry-over or wear on the piston rings or
valve plates.
Voltage and current draw.
Monitor at each loading stage and unload the compressor if either become excessive.
Jacket cooling water, plant room and wet bulb temperature.
Monitor jacket cooling inlet and outlet water temperatures and confirm flow / temperature
differential to ensure correct level of heat removal.
The occurrence of abnormal sounds and vibration.
In the event that either of the above occur then stop the compressor, investigate the cause and
rectify.
Refrigerant gas and oil leaks.
Stop the compressor, investigate the cause and rectify.
2.4 Compressor Shutdown

1. Evaporators should be kept in a vacuum but not excessively deep, therefore continue operation for
a short period after closing isolate valves.
2. Close the compressor suction stop valve.
3. Isolate the supply to the compressor motor.
4. When the compressor ceases to rotate, close the discharge stop valve.
5. Ensure the jacket cooling water supply isolate solenoid is de-energized closed.
2.5 Extended Period of Shutdown

In the event that the refrigerant system is to be left idle for an extensive period, then the following
actions are to be undertaken:
1. Refrigerant should be transferred to the liquid receiver.
Close the receiver outlet valve.
Circulate cooling water through the condenser and compressor.
Operate the compressor and monitor refrigerant level in the receiver, should the level rise
excessively then decant refrigerant into the appropriate storage / transportation cylinders.
When a 7 psi (0.5 Kg/cm [0.05Mpa]) suction pressure is achieved, then stop the compressor
and close the suction and discharge stop valves.
The system should be kept at a positive pressure to prevent air entering the system.
2. Perform a system refrigerant leak check.

3. Stop the circulation of cooling water and drain the cooling system, this is particularly relevant in
cold climates.
14
2.6 Operation of the Compressor Prior and Post Maintenance

Prior to maintenance tasks being performed the compressor must be purged of refrigerant gas
which shall be completed using the following procedure:
1. Open the discharge stop valve (both low and high sides of a compound compressor).
2. Close the suction stop valve (both low and high sides of a compound compressor).
3. Operate the compressor for 10 to 20 seconds.
4. Immediately after stopping the compressor close the discharge stop valve (both low and high sides
of a compound compressor).
5. Gradually open the purge valve (both low and high sides of a compound compressor). Standard
safety precautions should be used for the venting procedure, in the event that the refrigerant is
R717 then the vent line should be placed in a drum of water. Ensure that no water is allowed to
flow into the compressor.
6. Final venting shall be completed, by removing the vent plug fitted to the crankcase.
Maintenance tasks may now be undertaken after final confirmation that no gas pressure exists in the
compressor and that the appropriate electrical safety precautions have been performed.
Compressor air purging and setting post maintenance tasks shall be completed as follows:
1. Close fully both suction and discharge stop valves (low and high side).
2. Close fully drain and oil charging valves; ensure all plugs are fitted.
3. Ensure the air purge valve is open (both low and high side of a compound compressor).
4. Operate the compressor for 10 to 20 seconds to purge air.
5. Immediately after stopping the compressor close fully the purge valve (both low and high sides of
a compound compressor).
6. When the indicated oil pressure is below 2Hg (60mmHg [-0.08Mpa]) vacuum after
approximately 3 minutes, air purging is complete.
Should the indicated oil pressure rise rapidly, then the following should be checked to determine the
cause:
1. All plugs are fitted.
2. Drain and oil charging valves are fully closed.
3. After completing the appropriate gas and electrical safety precautions, remove and examine the
suction and discharge valves for correct installation / abnormal wear. Replace and / or refit as
appropriate.
When the compressor is operated for the purpose of gas or air purging, running time must be
kept to a minimum, as oil pressure cannot be maintained. Repeated starting and stopping of the
compressor is to be absolutely avoided, as inadequate lubrication will result.
2.7 Action to Prevent Liquid Carry-over

Either by excessive opening of expansion valves or sudden changes in refrigeration load,
incomplete evaporation of the refrigerant occurs and liquid is sucked into the compressor. This
may well lead to compressor seizure due to inadequate lubrication or possible failure of
internal components and therefore the situation must be rectified as a matter of urgency.
Circulation of the jacket water cooling supply should continue to prevent damage to the
crankcase by freezing water, however if the temperature of the discharge gas is abnormally
low then the water supply should be isolated and the jacket immediately drained of water.
The following are indications of liquid carry-over:
1. Suction line thermometer indicates near to the saturated temperature corresponding to the suction
pressure.
2. Frost may have formed on the suction part or side lower part of the crankcase.
3. Metallic sound may be heard, caused by the action of the safety head (liquid hammer sounds).
15
4. Oil foaming, as observed through the sight glass due to the mixing of oil and refrigerant.
5. A decrease in oil pressure due to the mixing of oil and refrigerant.
Action in the event of light liquid carry-over
From the above indications, should the frosting be light, metallic sounds are intermittent and the oil
pressure can be maintained then the liquid carry-over is comparatively less serious and the following
actions should ensue:
1. Throttle the suction stop valve to cause the liquid refrigerant to evaporate, which is indicated by
the decreasing level of frost on the crankcase.
2. Close the expansion valve. Continue compressor operation while maintaining oil pressure and
gradually open the suction stop valve. When the valve is fully opened and the suction line
thermometer indicates approximately 18F (10C) superheat, gradually open the expansion valve
and return to normal operation.
Action in the event of heavy liquid carry-over
Should the crankcase be heavily frosted, continuous liquid hammer sounds or the oil pressure cannot
be maintained then the following actions should be undertaken as continuing compressor operation
will result in mechanical failure:
1. Stop the compressor.
2. Close the compressor suction stop valve and expansion valve.
3. Close the compressor discharge stop valve.
4. Gradually open the oil drain valve and drain the lubricating oil.
5. Investigate the reason for the liquid carry-over and rectify as required.
6. Replenish the lubricating oil and purge air from the compressor.
7. Open the compressor discharge stop valve and start the compressor.
8. Gradually open the compressor suction stop valve (high side of compound compressor, followed
by the low side). Continue operation, ensuring that the oil pressure remains satisfactory, no
foaming occurs and frost does not form on the crankcase.
9. When the compressor suction valve is fully opened and the suction line thermometer indicates
approximately 18F (10C) superheat, then proceed to gradually open the expansion valve and
return to normal operation.
A methodical, patient approach will be required to rectify a heavy liquid carry-over, an operation that
may require several hours before normal operation can be restored.
Action in the event of liquid carry-over in the high side of a compound compressor
Liquid carry-over to the high side of a compound compressor is a rare occurrence but can originate
from an incorrectly set expansion valve of the intermediate cooler. The following actions are required
to remove liquid refrigerant from the high side chamber:
1. Fully close all expansion valves.
2. Regulate the high side suction stop valve and ensure the intermediate pressure does not exceed
100 psi. (7Kg/cm [0.7Mpa]).
3. Simultaneously regulate the low side suction stop valve and open the unloader solenoids to
maintain full oil pressure.
4. Continue regulating the high side suction stop valve until the indications of liquid carry-over have
returned to normal.
5. In the event that liquid carry-over has not occurred when the high side suction stop valve is fully
open and the thermometer indicates 18F (10C) superheat, then stop compressor operation,
perform further investigation and rectify. Return to normal operation and gradually open the
expansion valves.
On Freon systems not equipped with a high side suction stop valve continue normal operation with
caution, as refrigerant will exist in the intermediate cooler.
16
2.8 Fault Diagnosis and Rectification

FAULT INDICATION
I.
Starting
A. No reaction of the
motor, when start is
selected.
B. Current flows when
switch is operated but
disconnects when
released.
C. Motor groans but does
not turn.
D. Motor stops after 45

seconds.
E. Motor stops after short
period.
REASON
RECTIFICATION
1.
2.
3.
4.
5.
1.
2.
OPS and HPS are not reset.

Power or control fuse ruptured.
Incorrect contact of magnetic switch.
Over-current relay has operated.
Connections incorrect, wire severed.
Failed auxiliary contact.
Incorrect connection (on auto control).
1.
2.
3.
4.
5.
1.
2.
Investigate and reset as required.

Investigate and replace.
Inspect and repair.
Investigate and reset.
Inspect and repair.
Investigate and repair.
1.
2.
3.
4.
5.
1.
2.
3.
1.
2.
3.
4.
Belts too tight.

Malfunction in the electrical system.
Voltage drop.
Crankcase pressure high.
Compressor internal failure.
OPS operates
No increase in oil pressure.
Water flow switch no contact.
LPS / HPS operate.
Discharge stop valve is closed.
Refrigerant pressure too high.
Refrigerant pressure too low.
1.
2.
3.
4.
5.
1.
2.
3.
1.
2.
3.
4.
Adjust as required.
Confirm power supplies.
Lower pressure.
Investigate electrical and oil system.
Refer to IV.
Investigate electrical and water system.
Open.
Refer II.
Refer II.
17
FAULT INDICATION
II.
Abnormal
pressure
A. Suction pressure does

not decrease and discharge
pressure does not increase.
B. Discharge pressure too

high.
C. Suction pressure too

low.
REASON
1. Expansion valve opened excessively.
2. Safety relief valve leaks (when piped to
suction).
3. Unloader system inoperative.
4. Oil return valve open (compound
compressor).
5. Suction or discharge valve plate defective.
6. Piston ring or cylinder liner defective.
1. Inadequate supply of water or air to the
condenser.
2. Condenser tubes are fouled.
3. Air in the condenser.
4. Refrigerant over-charge.
1. Expansion valve insufficiently open.
2. Liquid line filter / drier blocked.
3. Liquid solenoid valve inoperative.
4. E.P.R. out of adjustment.
5. Refrigerant low charge.
6. Inadequate supply of water or air to the
cooler.
7. Excessive frost / ice on the cooling coil.
8. Oil accumulation in the cooling coil.
RECTIFICATION
1. Investigate and reset as required.
2. Replace.
3. Inspect and repair.
4. Investigate and close.
1. Investigate and supply as required.
2.
3.
4.
1.
2.
3.
4.
5.
6.
Investigate and clean.

Investigate and purge.
Decant refrigerant as required.
Investigate and reset as required.
Investigate and clean.
Confirm power supplies / repair.
Repair / reset as required.
Investigate and replenish.
Examine fans / pumps and repair.
7. Defrost and monitor.

8. Investigate and drain as required.
18
FAULT INDICATION
III.
Abnormal
temp.
A. Discharge temperature
too high.
B. Crankcase temperature
too high.
C. Oil temperature too
high exceeding 140F
(60C)
REASON
1.
2.
3.
4.
1.
2.
3.
1.
2.
3.
4.
5.
6.
IV.
Low oil
pressure
A. Oil pressure too low.
B. Oil pressure gauge

reading fluctuates (10 20
psi) [0.1 0.2 MPa]
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.
Inadequate water supply.

Discharge pressure too high.
Suction gas temperature too high.
Water jacket fouled.
Gas leakage from lapping part of discharge
assembly and cylinder liner.
Discharge valve plate is defective.
Piston rings or cylinder liner defective.
Oil pressure too high.
Defective bearing.
Inadequate supply of water (water-cooled oil
cooler).
Oil cooler fouled (water type).
Inadequate supply of refrigerant (refrigerant
cooled oil cooler).
Oil accumulation in refrigerant side of
cooler.
Oil foaming in the crankcase due to
refrigerant carry-over.
Crankcase heater is not energized.
Oil pressure gauge defective.
Oil temperature too high.
Suction pressure too low.
Oil strainer is clogged.
Suction strainer is clogged.
Bearing wear.
Oil pump wear.
Oil pump relief valve stuck open.
Oil strainer is clogged.
RECTIFICATION
1.
2.
3.
4.
1.
Increase water supply and examine tubes.

Refer IIB.
Adjust expansion valve superheat setting.
Inspect and clean.
Investigate and clean as required.
2.
3.
1.
2.
3.

Adjust (Refer 2-3).
Increase water supply.
4. Investigate and clean.

5. Clean filter and adjust expansion valve.
6. Warm oil cooler and drain oil.
1. Investigate the refrigerant carry-over and
change oil.
2. Confirm power supplies.
3. Replace.
4. Refer to IIIC.
5. Refer to IIC.
8. Replace.
9. Replace.
10. Examine and clean.
1. Investigate and clean as required.
19
FAULT INDICATION
V.
VI.
Oil usage.
Abnormal
noise
A. Excessive oil
consumption.
A. Safety head rising.
B. Liquid hammer, no
superheat, frost
formation on the
crankcase, oil foaming
and pressure down.
C. Crankcase
D. Transmission
REASON
1. Oil in the crankcase is foaming.
2. Poor oil return from oil separator or gas
counter flow.
3. Piston ring or cylinder liner worn.
4. Discharge valve plate defective (sudden rise
in consumption).
5. Oil return valve open (compound
compressor).
6. Cylinder liner O-ring is defective.
1. Metallic noise (oil hammer). Excessive oil
on the piston.
2. Safety head spring defective.
3. Broken valve plate, foreign matter on piston.
1.
2.
3.
4.
5.
6.
1.
Liquid carry-over.
Expansion valve is over-opened.
Rapid change in evaporator load.
Refrigerant is over-charged.
Liquid separator fails to function.
Liquid supply controls defective.
Bearing, piston ring or oil pump defective.
1. Belts slip
2. Incorrect coupling or loose coupling.
RECTIFICATION
1. Raise oil temperature or pressure in the
crankcase.
2. Investigate and repair.
3. Replace.
4. Investigate and replace.
5. Close.
6. Replace.
1. Refer to V.
2. Replace (refer to 3-5).
3. Investigate and replace.
1.
2.
3.
4.
5.
6.
1.
Refer to 2-7.
Adjust as required.
Adjust controls as required.
Decant to the correct level.
1. Adjust as required.
2. Investigate and adjust (refer to 3-23).
20
2.9 Pressure vs. Condensing Temperature and Evaporating Temperature

Refrigerant pressures always correspond to condensing and evaporating temperatures; this relationship
must be comprehended in order to operate correctly refrigerating equipment.
High pressure relative to saturated pressure corresponding to the condensing temperature leads to
decreasing compressor capacity and ultimately mechanical failure.
A normal condition of operation will exist when the suction gas temperature of the compressor is 18
to 36F (10 to 20C) [superheat] higher than the temperature corresponding to suction pressure
(evaporating temperature). Liquid carry over is more likely to occur when the temperature difference
[superheat] between suction gas temperature and the temperature corresponding to suction pressure
(evaporating temperature) decreases.
Should the temperature difference increase a reduction in compressor capacity will be observed with
possible mechanical failure of the compressor due to the rising discharge temperature.
Close attention should be maintained during the operation of refrigeration equipment to the pressure
and temperature ratios.
Condensing &
Evaporating
Temperature
- 70 C
- 60 C
- 50 C
- 40 C
- 35 C
- 30 C
- 25 C
- 20 C
- 15 C
- 10 C
- 5 C
0 C
5 C
10 C
15 C
20 C
25 C
30 C
35 C
40 C
45 C
- 94 F
- 76 F
- 58 F
- 40 F
- 31 F
- 22 F
- 11 F
- 4 F
5 F
14 F
23 F
32 F
41 F
50 F
59 F
68 F
77 F
86 F
95 F
104 F
113 F
Saturated Pressure
R 717
Gauge
Pressure
MPa
Absolute
Pressure
MPa
Gauge
Pressure
PSIG
67.8cmHg
59.6cmHg
45.4cmHg
0.04
17.8Hg
22.2cmHg
0.07
6.20cmHg
0.02MPa
R 22
Absolute
Pressure
PSI
Gauge
Pressure
MPa
Absolute
Pressure
MPa
Gauge
Pressure
PSIG
Absolute
Pressure
PSI
0.01
60.7cmHg
0.02
24.07Hg
2.87
0.02
47.9cmHg
0.04
18.85Hg
5.44
5.93
27.6cmHg
0.06
10.90Hg
9.34
8.7Hg
10.41
0.04MPa
0.10
0.53
15.22
0.09
2.4Hg
13.52
0.03
0.13
4.36
19.10
0.12
2.6
17.34
0.06
0.16
9.01
23.71
0.05
0.15
8.5
23.15
0.10
0.20
15.81
30.50
0.09
0.19
12.9
27.59
0.14
0.25
20.81
35.50
0.13
0.24
19.6
34.27
0.19
0.30
28.11
42.81
0.19
0.29
27.5
42.18
0.25
0.36
36.69
51.38
0.25
0.36
36.8
51.47
0.32
0.42
46.37
61.13
0.33
0.43
47.6
62.29
0.40
0.50
57.47
72.17
0.41
0.52
60.1
74.80
0.48
0.58
70.00
84.65
0.51
0.61
74.5
89.19
0.58
0.68
84.03
98.73
0.63
0.73
90.9
105.6
0.68
0.79
99.30
114.52
0.76
0.86
109.6
124.3
0.80
0.91
117.28
131.97
0.90
1.00
130.7
145.4
0.94
1.04
136.65
151.45
1.07
1.17
154.5
169.2
1.09
1.19
158.17
172.87
1.25
1.35
181.1
195.8
1.25
1.36
182.00
196.40
1.45
1.55
210.7
225.4
1.43
1.53
207.72
222.42
1.68
1.78
243.7
258.4
1.63
1.73
236.05
250.7
1Kg/cm = 0.09807MPa = 98.07kPa
21
HASEGAWA
3. MAINTENANCE
The following maintenance procedures explain the construction, disassembly, inspection, reassembly
and adjustment, which should be fully comprehended prior to performing maintenance tasks.
3.1 Preparation
To confirm the existence of defects and to effectively perform compressor maintenance the following
daily observations should be performed:
1. Suction and discharge pressure.
2. Suction and discharge temperature.
3. Lubricating oil pressure and temperature.
4. Oil consumption and condition.
5. Mechanical noise and vibration.
3.2 Precautions
Prior to maintenance activity ensure that:
1. Mechanical and electrical safety precautions are completed in accordance with current regulations.
2. The air purge valve, (both low and high side) is fully opened and pressure is released and
confirmed at atmospheric pressure.
3. The external casing of the compressor is cleaned of dust, oil and moisture to prevent ingress of
foreign matter into an open compressor.
4. Maintenance equipment must be clean.
5. Disassembled parts should be placed in a logical order and in a clean environment.
6. Fresh kerosene should be used for cleaning parts prior to examination.
7. For extended periods of disassembly, a water-repellent coating should be applied to parts.
8. Reassembly should be completed only after removing any applied protective coatings and
applying fresh refrigerant oil to all parts.
3.3 Maintenance Schedule

The following table shows a general standard for periodic preventative maintenance, however due
consideration must be given to the operating condition and environment of the compressor.
22
Inspection Item
Inspection Points
Inspection period
Running condition
Lubrication oil
Oil screen, oil filter and
gas suction screen
Refer to (2.3) and (3.1).

Sample and replace as required.
Examine, if metallic particles are
visible inspect bearings / pistons etc.
Clean crankcase internally and
change oil.
Examine rubber element and replace
as required.
Ensure attachment bolts secure.
Examine belts and replace as
required.
Check set-value and test.
Check set-valve and test.
Check for indication error against
calibrated equipment.
Check working pressure.
Daily / Monthly / Annually

Monthly / Annually
Monthly / Annually
Coupling
Belt
Oil protection switch
High / Low switch
Thermometer and
Pressure gauges
Safety relief valve
Maintenance
Monthly / Annually
Monthly / Annually
Monthly / Annually
Monthly / Annually
Monthly / Annually
Annually
12000 run hours / annually
Discharge & suction

valves
Inspect for wear and defects.

Check height of safety headspring.
Change valve springs.
Piston, Piston ring,

Piston pin & Piston pin
bearing
Inspect for wear, defects and carbon

deposits.
Every maintenance
20000 hours R717
12000 hours R22
Cylinder liner
Crank pin bearing
Crankshaft
Inspect for defects.

Inspect for wear and pitting.
(Overhaul journal part)
Clean
Every maintenance
Every maintenance
Every maintenance
20,000 run hours
Every maintenance
20,000 run hours
Inspect for wear and oval.

Inspect for wear leakage.
Inspect for wear and oval.
Inspect for wear pitting.
Replace
20,000 run hours

20,000 run hours
20,000 run hours
20,000 run hours
20,000 run hours
Oil cooler
Crankshaft bearing
journal
Front bearing
Mechanical seal
Rear bearing
Oil pump
Motor bearing
(Flanged motor)
23
3.4 Maintenance Procedures (M.P.)

CONTENTS
M.P. 1
Cylinder Head Cover
M.P.2
Suction & Discharge Valves
M.P.3
Piston & Piston Rings
M.P.4
Cylinder Liner
M.P.5
Unloader Assembly
M.P.6
Mechanical Seal Assembly
M.P.7
Front Main Bearing
M.P.8
Oil Pump Assembly
M.P.9
Rear Main Bearing
M.P.10
Crankshaft
M.P.11
Oil Pressure Regulator Valve
M.P.12
Oil Return Valve
M.P.13
Oil Screen & Oil Filter
M.P.14
Oil Cooler
M.P.15
Crankcase Heater
M.P.16
Suction Gas Strainer
M.P.17
Safety Relief Valve, Pressure Gauge & Pressure Switch
M.P.18
V Belt Drive
M.P.19
Coupling Direct Drive
M.P. 20
Flanged Motor
24
M.P. 1 Cylinder Cover

Associated Instructions
Required Tools
A.
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
Refer: 2.2, 2.3, 2.5,2.6, 2.7 & 3.2

Hasegawa & General purpose
Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Isolate the compressor both mechanically and electrically.
Close the suction and discharge valves, including intermediate valves (if applicable).
Vent refrigerant gas and confirm pressure is indicated at 0 psi.
Isolate cooling water supply and drain cooling water.
Remove water pipes and clean compressor casing to prevent foreign material ingress.
Remove unloader oil pipes (as required).
Loosen bolts quantity 14, size (M14).
Remove two opposite bolts and fit guide bolts.
Remove remaining 12 bolts in diagonal format. The cover will lift by the force of the safety
headspring.
Remove cylinder cover and strip gasket; ensure foreign material does not enter the cylinder.
Torque Loading:
Table 1
114 128 lb. ft (16 18 kg-m)[160 180Nm]
Inspection
a) Examine cylinder cover for indications of impact damage and cracks.
C. Refitting
Refer: 2.7, 2.2 & 2.3
a) Apply refrigerant oil to both sides of a new gasket and place on casing with guide bolts to
correctly locate the gasket.
b) Fit 12 bolts and engage threads, remove guide bolts and fit the 2 remaining bolts.
c) Fasten bolts in a diagonal format, in accordance with (Fig. 1).
d) Torque-load the bolts to the setting above in accordance with Table1.
e) Refit the external unloader oil pipes as required.
f) Refit the water pipes and re-establish the jacket cooling water supply.
g) Restart the compressor using the correct procedure.
h) Perform the appropriate leak checks.
25
Hexagon Bolt Table

Size
M14
Torque Loading
Lbs/ft (kgm)
122 (17.0)
Allen Wrench Size

(mm)
12
M12
77 (10.7)
10
M10
M8
M6
44 (6.2)
22 (3.1)
9 (1.3)
8
6
5
M5
5 (0.7)
Location
Cylinder cover, side cover, suction strainer
cover, rear cover, motor end cover & motor body
Oil screen cover, oil pump, oil tank cover,
crankshaft key plate & motor end shaft
Oil pump & seal cover
Oil pump cover
Cylinder jacket cover, case jacket cover, front
metal, rear metal, unloader valve & relief valve
Unloader cylinder cover
26
M.P. 2 Suction and Discharge Valves

Required Tools
Refer: M.P. 1
Hasegawa & General purpose
A. Description
The suction valve assembly is comprised of the following components, outer seat (1), which is
recessed to locate eight springs (2) that sit on the valve plate (3). This valve assembly is held in
place by the cylinder cover. The discharge assembly comprises a safety spring (4), valve guide (5),
six springs (6), plate (7) and inner seat (8). Components 5, 6, 7 and 8 are bolted together, the unit
is held in place by the action of the safety springs on the cylinder cover.
Removal
a) Remove the cylinder cover in accordance with M.P. 1.
b) Remove the discharge valve assembly and safety-head spring from the outer seat.
c) Remove the outer valve seat including springs, spring holders and suction plate from the
compressor casing.
B. Inspection
Place components on a clean work surface and clean with new kerosene.
a) Remove the safety spring from the discharge valve assembly. Examine spring for deformation and
cracking. Test springs for height in accordance with Table-2 (Fig 3). Replace as required.
Safety Head Spring
Free height standard (L) VK / VKL
Limit for use(L) VK / VKL
Table 2
Tolerance
2.5" (63.5mm) / 2.2 (56mm)
2.4 (61.5mm) / 2.1 (54mm)
b) Remove suction valve springs and spring holders from the outer seat. Examine springs for
deformation and cracking. Test in accordance with Table-3 (Fig 4). Replace as required.
c) Disassemble the discharge valve assembly by removing the lock nut and loosening the nut to
allow spring and holder removal, ensuring the locating pin is not dislodged. Examine springs for
27
deformation and cracking. Test the springs in accordance with Table-3 (Fig 4). Replace as
required.
d) Examine inner and outer seats for damage. Replace as required.
e) Examine suction and discharge plates for scoring (maximum allowable 0.2mm) and cracking.
Replace as required.
Suction and Discharge Valve
Spring
Free height standard (L)
Limit for use (L)
Coil outer diameter (A)
Seat outer diameter (B)
Spring line diameter (d)
Quantity fitted
Suction
Tolerance
0.595 (15.1mm)
0.555 (14.1mm)
0.256 (6.5mm)
0.284 (7.2mm)
0.028 (0.7mm)
8
Discharge
Tolerance
0.595 (15.1mm)
0.555 (14.1mm)
0.256 (6.5mm)
0.284 (7.2mm)
0.028 (0.7mm)
6
Table 3
f) Refit springs and spring holders into the recesses of the outer seat and inner seat, by winding the
larger coil (Fig 4 [B]) into the recess.
g) Torque load the male and female nuts of the discharge valve assembly in accordance with Table 4
below, ensuring the male nut is fitted before the female and the locator pin remains in the seat.
h) Refit safety springs to the valve guide by locking the coil with the flat washer.
Torque
Lbs.ft (Kg-m)[Nm]
Table 4
Male
28 35 (4 5)[40 50]
Female
21 25 (3 3.5)[30 35]
C. Refitting
This operation must be undertaken using clean refrigeration oil and lint free cloths, ensuring no
foreign particles are allowed to enter the compressor.
a) Place the suction plate on to the top of the cylinder liner.
b) Ensure 8 springs and holders are fitted to the outer seat; place the outer seat inside the casing on
top of the suction plate (Fig. 6). The seat will remain proud of the casing by spring tension but can
be pushed flush with the casing to ensure correct positioning.
c) Fit the discharge assembly to the outer seat and rotate to ensure a correct fit.
d) Refit the cylinder cover in accordance with M.P. 1.
28
D. Servicing Notes
a) As shown in (Fig. 2) both the suction valve assembly and discharge valve assembly are held in
place by the cylinder cover, therefore under no circumstances can the compressor be operated
without these components or the cylinder cover being correctly fitted.
b) On all models identifying stamp marks (A, B, C etc.) are applied to each cylinder and its
associated components, therefore components being refitted should be done so at the correct
location.
c) Compressor conversion from Ammonia to Freon or vice versa should only be attempted after
consultation with Hasegawa, as some components are unique to each application.
Outer Seat
Discharge Valve Assembly
29
M.P. 3 Piston and Connecting Rod Assembly

Required Tools
Refer M.P. 1 & 2

Hasegawa & General Purpose
A. Description
The piston and connecting rod assembly can be disassembled for inspection purposes and are
identified as piston (1), piston rings quantity three (2), piston pin (3), plain bearing or needle
bearing (4), connecting rod (5), crankshaft plain bearing (6) and rod bolts (7). The needle bearing
(4) is fitted to the high side of a compound compressor only.
Removal
a) Remove the cylinder cover in accordance with M.P. 1.
b) Remove the suction and discharge valve assemblies in accordance with M.P. 2.
c) Drain lubricating oil from the lower casing.
d) Remove side-cover quantity two and discard the gaskets.
e) Identify the correct piston assembly end cap, rotate the crankshaft to the most suitable position and
remove quantity two female lock nuts and two male nuts securing the end cap. Remove the end
cap with the lower half of the plain bearing.
f) Screw the eyebolt ancillary tool (x 2) into the locating holes in the flange of the liner and rotate the
crankshaft so that the appropriate piston is at the middle position.
g) Gradually ease the piston / liner assembly up and out of the casing and keep the connecting rod
central within the liner, ensuring that the connecting rod bolts do not become jammed under the
bottom of the casing. Separate piston and liner assemblies by removing through the bottom of the
liner. Refer to M.P.4, with respect to liner examination.
Note: For RM type compressor remove the plug at the center of the motor, attach the hexagonal bolt
ancillary tool and turn the shaft by a motor T wrench ancillary tool to the lowest position.
B. Inspection
Piston and Piston Ring
a) Place piston and connecting rod assembly on a clean work surface and clean with new kerosene.
b) Remove lower half of the plain bearing from the end cap and the upper half from the connecting
rod. Remove connecting bolts.
c) Remove the piston rings quantity three from the piston.
d) Examine the piston, connecting rod and associated cylinder liner for defects.
30
e) Using the eyebolt refit the piston into the liner and measure the clearance between the piston (1)
and liner (2) at the first and second land (Fig. 8). This measurement must be observed at the thrust
direction of the piston (at right angle to the piston pin) and the tolerances within the limits as
specified in Table 5.
Piston
Standard
Maximum Tolerance
Table 5
First Land in.(mm)

0.0047 0.0071 (0.12 0.18)
0.0138 (0.35)
Second Land in.(mm)

0.0012 0.0035 (0.03 0.09)
0.0138 (0.35)
f) Remove the piston and connecting rod from the cylinder liner and examine each piston ring.
g) Three rings are fitted to each piston (Fig. 9):
1st ring compression ring, chrome plated square section
2nd ring compression and oil control ring under cut
3rd ring oil scrapper ring, chrome plated.
h) Each ring should be fitted to the associated liner (Fig. 10) and the joint clearance checked in
accordance with Table 6. Replace rings with excessive clearance.
Piston Ring
Standard
Maximum Tolerance
Table 6
Clearance in.(mm)
0.0118 0.0197 (0.30 0.50)
0.039 (1.00)
Piston Pin and Piston Pin Bearing

i) The piston and pin assembly, do not require to be disassembled unless movement or irregular
motion is observed during examination.
j) The piston and pin are close tolerance fitted and require heating in oil at 160 to 180F to
facilitate separation. After heating, separation can be achieved by the application of pressure to the
pin.
k) A plain bearing is fitted to the small end of the connecting rod on single stage compressors and the
low side of compound compressors. A needle roller bearing is fitted to the small end of the high
31
side of compound compressors and although interchangeable, a plain bearing cannot be used on
the high side, as rapid deterioration of the bearing will occur.
l) The plain bearing is a pressed fit and the tolerances are in Table 7.
Piston Pin Bearing
Tolerances in.(mm)
Standard
0.0008 0.0018 (0.020 0.045)
Maximum Tolerance
0.0059 (0.15)
Table 7
m) The needle roller bearing is a close tolerance fit and to facilitate replacement remove the lock
ring and heat components in oil is required.
n) Ensure that the oil passage is horizontal when replacing the needle roller bearing.
Needle Bearing Oil Passage Orientation
Piston Pin Insertion
Crank Pin Bearing and Connecting Rod

o) The crank pin bearing is manufactured by applying white metal to a steel backing and is in two
parts, upper and lower.
p) It is not permitted to perform any manner of adjustment to the bearing or connecting rod big end
as strict tolerances are adhered to during manufacture. Installation tolerances (Fig. 11) in Table 8.
Crank Pin Bearing
Standard
Maximum Tolerance
Table 8
Tolerances in.(mm)
0.0012 0.0028 (0.03 0.07)
0.008(0.20)
q) The connecting rod big end and the bearing are stamped during manufacture to ensure correct
assembly.
r) Reassembly of the piston and connecting rod assembly is the reverse of the removal procedure.
s) Utilize the oil bath or hydraulic press to facilitate the fitting of the piston pin bearing (plain or
needle), piston pin and piston.
t) Piston rings should be fitted so that the manufacturers mark is up and arranged so that the three
joints are 120 apart, avoiding the piston thrust direction.
u) Fit the rings in reverse order commencing with the 3rd ring and ensuring that each ring is fitted in
the correct manner (Fig. 9).
32
NOTE: The piston connecting rod assembly is fitted into the liner from the bottom prior to installing
the liner and is held in position using the eye bolt tool. Locate the cylinder liner in the casing in
accordance with MP4.
Piston Connecting Rod Installation Into Liner
Assembly Installation Into Crankcase
33
C. Refitting
a) Ensure that the upper half bearing, connecting rod bolts and eye bolt are fitted to the piston
assembly and raise the piston / liner assembly into the casing (Fig. 12) using liberal quantities of
lubricating oil.
b) Pay attention to the cylinders, which have pistons fitted without covers, as the cylinder liners are
likely to rise with the piston during crankshaft rotation.
c) Place the crank at the middle position and guide the connecting bolts over the crankshaft ensuring
that the bolts do not score the crank journal.
d) Fit the bearing lower half to the end cap and install the end cap. Place flat washer and male nut on
each bolt, torque load in accordance with Table 8 using a long reach socket.
e) Fit the female nut to each bolt, torque load in accordance with Table 9 using a standard socket, as
extreme care must be taken not to further tighten the male nut.
Rod Bolt Nut
Torque Lbs.ft (Kg-m)[Nm]
Table 9
f)
g)
h)
i)
Male Nut
28 36 (4 5)[40 50]
Female Nut
14 21 (2 3)[20 30]
Ensure internal casing is clean and using new gaskets refit the side covers.
Refit the suction and discharge valve assemblies in accordance with M.P. 2.
Refit the cylinder covers in accordance with M.P. 1.
Replenish the lubricating oil system.
34
M.P. 4 Cylinder Liner

Required Tools
Refer M.P. 1, 2 & 3

A. Description
Two types of cylinder liners are fitted to compressors, type A and type B. Type A liners are
fitted with a locating peg in the rim to ensure correct engagement of the unloader cam ring and
knock pins of the unloader mechanism. Type B liners are fitted to the high side of compound
compressors and to the non-unloading cylinders of the low side. The flange thickness is as
follows: VK 0.55 (14mm)
VKL 0.85 (21.5mm).
B.
a)
b)
c)
d)
e)
Removal
Remove the cylinder cover in accordance with M.P. 1.
Remove the suction and discharge valve assemblies in accordance with M.P. 2.
Fit the eyebolts (Fig. 13) to the liner.
Remove the piston / liner assembly in accordance with M.P. 3.
Lift the cylinder liner and piston assembly from the casing with steady force. Caution: as soon as
the resistance of the O ring has been over come the cylinder liner is free to be removed.
C.
a)
b)
c)
d)
e)
f)
Inspection
Remove and discard the cylinder liner shim.
Place the cylinder liner on a clean work surface and clean with new kerosene.
Clean and examine the cylinder liner-casing seat.
Remove and discard the cylinder liner O-ring.
For inspection information on cylinder liners fitted with an unloader mechanism refer to M.P. 5.
Examine the upper and lower surfaces of the flange, damage is not permitted as these surfaces
form a gas tight seal with the discharge valve outer seat and the casing.
g) Examine the suction valve seat for defects, damage is not permitted.
h) Examine the inner surface of the liner for excessive wear, cracks or roughness. The limits for use
are stated in M. P. 3, Table 6 (Fig. 10) and should the tolerances not be achieved when new piston
rings are tested, replacement of the cylinder liner is required.
35
i)
j)
Fit a replacement O-ring (Fig. 14), ensuring that when fitted into the groove on the liner that
twisting or over-extending has not taken place. Failure of these practices could result in low
efficiency and excessive oil consumption.
Fit a replacement cylinder liner shim to the casing seat.
NOTE: The piston connecting rod assembly must be inserted into the liner from the bottom of the liner
prior to installation of the liner using the eye bolt tool in accordance with M.P.3.
D. Refitting
a) Apply refrigerant oil to the O-ring.
b) Using the eyebolt tools, place the liner into the casing at the same time ensuring that the shim is
not damaged.
c) For liners with the unloader mechanism, ensure that the correct orientation has been achieved and
engagement of the cam ring with the unloader piston.
d) Apply steady pressure to the eyebolt tools until the liner / piston assembly descends onto the
casing seat (Fig. 15).
e) Refit the suction and discharge valves in accordance with M.P. 2.
f) Refit the cylinder head cover in accordance with M.P. 1.
36
M.P. 5 Unloader Operating Mechanism

Required Tools
Refer M.P. 1, 2, 3 & 4

A. Description
The unloader mechanism for each bank of cylinders (Fig. 16) which are designated to be
unloaded consists of the following components, operating piston assembly (secured to the
casing), cam ring, pins with springs and knock pins (assembled on the liner). Oil pressure is
fed via external piping from the pump to a tee connection, the return line to the casing is via
a solenoid and the supply line to the piston assembly is via a restrictor and a tapping. When a
load signal is generated a solenoid will close and oil pressure is fed via the restrictor to the
piston assembly, over coming internal piston spring pressure to force the piston off its seat.
This provides rotational movement of the cam rings, lowering the cam pins to enable the
suction plate to lower on to its seat, which ensures that the only passage open for the
compressed gas is to discharge. Conversely when an unload signal is generated a solenoid
will open and provides a passage for oil in to the crankcase. Internal spring pressure in the
piston assembly forces the oil out, through the restrictor and open solenoid in to the crankcase,
enabling rotation of the cam ring, raising the cam pins thereby allowing recirculation of the
refrigerant gas around the head assembly.
B.
a)
b)
c)
d)
Removal
Remove the cylinder cover in accordance with M.P. 1.
Remove the suction and discharge assemblies in accordance with M.P. 2.
Remove the piston / liner assembly in accordance with M.P. 3 & 4.
Locate the hollow bolt, which secures the unloader piston assembly to the casing and remove,
thereby releasing the piston assembly from the casing.
37
C. Inspection
a) Invert the cylinder liner (Fig. 17) (1) and extract the knock pins (3), which will facilitate removal
of the cam ring (2).
b) Remove the cam ring from the liner piston assembly and remove the three pins (4) along with the
springs.
c) Clean and examine the pins and springs for cracks and deformation, replace as required.
d) Reassemble the components ensuring that the cam ring is correctly orientated (rings are right and
left-handed).
e) Disassemble the piston assembly (Fig. 18) by first removing the clip (7) and working plate (6)
from the piston stem.
f) Remove the end plate (2) securing bolts with extreme caution due to spring pressure; remove the
piston (3) and spring (4).
g) Clean and inspect the cylinder (1) and piston (3) for excess wear and the spring (4) for
deformation.
h) Replace the packing (5) and o-rings (8 & 9).
i) Reassemble the piston assembly using extreme care that no foreign matter enters the cylinder as
damage to the packing may occur which, will cause excessive oil consumption.
D. Refitting
a) Refit the piston assembly to the casing but do not tighten fully the hollow bolt.
b) Refit the cylinder liner on the oil pump side in accordance with M.P. 4, ensuring that the pins are
seated on the highest portion of the cam (unloaded position) (Fig.19).
c) Ensure that the piston assembly working plate engages the slot on the cam ring and that outward
movement of the piston would rotate the cam ring allowing the pins to run in to the indent on the
cam ring.
d) Place a locally manufactured tool, (0.0393in. 1mm thick steel sheet) between the working plate
and the cam ring (Fig. 16) dimension A to obtain the correct clearance on the installed liner cam
ring.
e) Tighten the piston assembly-locating bolt and confirm dimension A as correct.
38
f) Fit the adjacent cylinder liner / piston assembly in accordance with M.P. 3 & 4, ensuring that the
working plate engages correctly with the cam ring and thereby confirming that the four cam ring
pins are positioned correctly on the upper portion of the cam ring.
g) Cross check the pin height to the adjacent cylinder and then by placing both the suction valve plate
and outer seat in the correct position on each liner that the outer seat sits in the correct position
(Fig. 19).
h) Ensure that a gap exists between the plate and outer seat and that the suction plate is able to sit
fully in its seat when the pin is lowered for loading (Fig 19).
i) Refit the piston assemblies in accordance with M. P. 3.
j) Refit the suction and discharge valve assemblies in accordance with M. P. 2.
k) Refit the cylinder cover in accordance with M. P. 1.
E.
Unloader Operating Valve Mechanism

The system operates via a taping on the oil pump body and external piping to a solenoid(s) for
automatic operation or a hand valve for manual operation. When a solenoid is energized the valve
is opened and oil pressure is relieved back to the casing, this is the condition at start-up allowing
the compressor to start partially loaded. When a solenoid de-energizes it will close allowing oil
pressure to operate the piston and cam assembly. The manual valve lever is placed in the lowest
position prior to compressor shut down and prior to start-up. To increase the loading on the
compressor gradually raise the lever (Fig. 20).
39
M.P. 6 Mechanical Seal Assembly

Required Tools
Refer 2.2, 2.3, 2.5, 2.6, 2.7 & 3.2

A.
Description
The mechanical seal assembly (Fig. 21) is composed of a cover plate (1), seal ring (2), bellow
type rubber packing (3), spring (4) and spring retainer. Lubricating oil and refrigerant gas are
prevented from escaping by the action of the bellows on the shaft and the seal ring on the
cover plate.
B.
a)
b)
c)
d)
e)
f)
Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Vent the compressor to equalize atmospheric pressure.
Ensure the compressor is electrically locked out.
Remove the V-belts, belt guard and flywheel or coupling guard and coupling.
Remove the cover plate mounting bolts, cover plate and seal ring.
Attach the two-extractor bolts to the spring retainer, which will ease off the front bearing seat.
Avoid wrenching and forced pulling.
C. Inspection
a) Examine the spring for deformation and replace as required.
b) Measure the seal ring in accordance with Table 10 (Fig. 22).
Seal Ring
Standard Thickness
Limit for Use
Table 10
Tolerances in.(mm)
0.354 (9)
0.314 (8)
c) Examine the rubber bellows and crankshaft for indications of abnormal wear.
d) The rubber bellows should be discarded and replaced by a new item.
e) The plate and seal ring may be returned to the factory for re-lapping and then kept as spare for the
original compressor.
40
Spring Retainer Installed
Spring & Seal Installation
Front Cover Installation
Mechanical Seal Assembly Installed
D.
a)
b)
c)
Refitting
Refer: 2.7, 2.2 & 2.3
Apply copious amounts of clean lubricating oil the crankshaft.
Carefully slide the seal assembly on to the shaft until the spring retainer abuts the front bearing.
Fit the cover plate ensuring that the drain orifice is at the lowest position and tighten bolts
gradually in a diagonal format to seat the seal correctly.
d) Refit the flywheel, belt guard and belts or coupling and guard. Tension belts or ensure correct
alignment of the coupling.
e) Re-establish the compressor both mechanically and electrically. Purge the compressor as required.
NOTE: On compressor start-up observe the seal drain point, after a period of bedding in the new seal
the oil leakage rate should not exceed 2 3 drops per minute. Only in the event of excessive oil or gas
leakage should the compressor be stopped and the fault investigated.
f) On RM, AM type compressors the seal assembly can only be accessed after removing the motor
rotor and then the cover plate. Drain the lubricating oil prior to removing the cover plate to ensure
that no oil is able to contaminate the motor stator. To facilitate oil-draining remove the oil supply
pipe from the oil filter and the drip tube, after which proceed as described above.
41
M.P. 7 Front Bearing

Required Tools
Refer M.P. 6
A.
Description
The front plain bearing is designed to bear the thrust load in an axial direction, the shaft load
and lateral movement of the shaft. Externally set in to the casing the bearing is secured in
place with four bolts. Bearing inspection may be undertaken with or without the crankshaft
installed.
B.
a)
b)
c)
Removal
Remove the compressor driving system and mechanical seal assembly, in accordance with M.P. 6.
Remove the four mounting bolts (Fig. 23).
Fit the extractor tool and ease the bearing from the casing.
C. Inspection
a) Clean the bearing with new kerosene.
b) Examine the bearing surface for an irregular wear pattern, metal flow to the oil passages and signs
of foreign object damage.
NOTE: Slight metal flow may be observed in the direction of rotation and is symptomatic of oil
priming on start-up or oil foaming due to liquid carry-over. Such a bearing may be used, however
consult the factory for guidance.
c) Refit the bearing on to the crankshaft and measure the clearance, Table 11 (Fig. 24).
Front Bearing
Standard clearance
Limit for use
Table 11
Tolerance in.(mm)
0.002 ~ 0.004 (0.05 ~ 0.10)
0.08 (0.2)
d) Should the bearing clearance exceed the limits in Table 11, replace the bearing.
42
Front Bearing Installed
Clearance Check To Crankshaft
D. Refitting
a) Apply copious quantity of lubricating oil to the bearing surface, set the bearing so that the oil
holes align with the oil grooves in the crankcase (horizontal) and tighten the bolts.
b) Refit the mechanical seal in accordance with M.P. 6.
c) Refit the compressor drive system in accordance with M.P. 5.
43
M.P. 8 Oil Pump Assembly

Required Tools
A.
Refer 2.2, 2.3, 2.5, 2.6, 2.7 & 3.2

Description
The oil pump assembly is fitted to the casing rear cover and is of the trochoid type (Fig. 25).
Oil is drawn through a strainer located in the lower casing and an external pipe to the pump
base (1). The pump is located in the body (2), which is driven by a shaft (3) that connects to
the rear of the crankshaft. Oil is supplied at pressure through a fitting located on the top of the
pump base. Standard rotation of the pump is counter clockwise as viewed at the pump,
however if due to installation requirements the compressor is required to rotate in the reverse
direction no reconfiguration is required (Fig. 26).
No.
1
2
3
4
5
6
7
Part
Pump Body
Pump Cover
Shaft
Rotor Pin
Outer Rotor
Inner Rotor
Reversing
Retainer
Qty.
1
1
1
1
1
1
1
Remark
No.
8
9
10
11
12
13
14
Part
Steel Ball
Steel Ball
Spring
Spring
Packing
Cover Bolt
Spring
Washer
Qty.
1
1
1
1
1
8
8
Remark
Retaining
Check
Retaining
Check
B.
a)
b)
c)
d)
e)
f)
Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Vent the compressor to equalize atmospheric pressure.
Ensure the compressor is electrically locked out.
Remove the four bolts, which attach the external oil feed pipe to the pump base.
Disconnect the oil outlet pipe from the pump base.
Remove the four bolts, which secure the pump body to the base and withdraw the pump complete
with shaft (Fig. 25).
g) Remove the four bolts, which secure the pump base to the casing and remove the casing.
h) Discard the pump base, pump body and feed pipe gaskets.
44
C. Inspection
a) Observe the plate and gear orientation within the body to ensure that reassembly is correctly
completed (Fig. 26).
b) Remove the bolts, which secure the end plate (1), withdraw the plate from the locating taper pin
and gear (2).
c) Examine the pump gears for indications of excessive wear and foreign object damage, particularly
the tooth areas.
d) Examine the shaft and bearing surfaces for indications of excessive wear and alignment.
e) Examine the inner surfaces of the pump body for excessive indications of wear and foreign object
damage.
f) Remove the oil pump relief valve from the pump base (Fig. 27).
g) The valve is designed to bleed excess oil pressure to the crankcase and is to be cleaned with new
kerosene as low oil pressure may occur if the valve seat is contaminated.
h) Refit the valve to the pump base and secure in place by center punching the threads to lock the
valve in place.
i) Refit the pump gears and end plate, ensuring that the plate is fitted in accordance with the standard
direction (Fig.26) unless the compressor is configured for reverse operation.
j) Ensure the end plate locates on the taper pin and fit the bolts to secure the plate.
NOTE: For marine compressors an additional oil tank is fitted below the casing to ensure positive oil
supply to the pump (Fig. 28). The oil strainer is removed from the casing and is located in the oil tank.
D.
a)
b)
c)
Refitting
Refer: 2.7, 2.2 & 2.3
Refit the pump base to the casing with a new gasket and fit mounting bolts.
Reconnect the oil feed pipe with a new gasket and oil outlet pipe to the pump base.
Orientate the oil pump drive spindle end key to the mating slot on the crankshaft and fit the oil
pump body to the base with a new gasket.
d) Ensure the correct pump orientation and that the pump is flush with the pump base.
e) Fit the pump body mounting bolts.
f) Rotate the compressor by hand to ensure positive oil feed to the pump.
45
46
M.P. 9 Rear Bearing

Required Tools
Refer M.P. 8
A.
Description
The rear plain bearing is designed to bear the thrust load in an axial direction as well as the
shaft load and functions as thrust metal on an edged surface. Located in the rear casing the
bearing is secured in place with two bolts. Bearing inspection may be undertaken with or
without the crankshaft installed.
B.
a)
b)
c)
Removal
Remove the oil pump assembly in accordance with M.P. 8.
Remove the rear cover and discard the gasket.
Remove the two bolts and using the extractor tool ease the bearing from the housing (Fig 28).
C. Inspection
a) Clean the bearing with new kerosene.
b) Examine the bearing surface for an irregular wear pattern, metal flow to the oil passages and signs
of foreign object damage.
NOTE: Slight metal flow may be observed in the direction of rotation and is symptomatic of oil
priming on start-up or oil foaming due to liquid carry-over. Such a bearing may be used, however
consult the factory for guidance.
c) Refit the bearing on to the crankshaft and measure the clearance, Table 12 (Fig. 29).
d) Should the bearing clearance exceed the limits in Table 12, replace the bearing.
Rear Bearing
Standard clearance
Limit for use
Table 12
Tolerance in.(mm)
0.002 ~ 0.004 (0.05 ~ 0.1)
0.008 (0.2)
47
Clearance Check To Crankshaft

D. Refitting
a) Apply copious quantity of lubricating oil to the bearing surface, set the bearing so that the oil
holes align with the oil grooves in the crankcase (horizontal) and tighten the bolts.
b) Refit the rear cover with a new gasket.
c) Refit the oil pump assembly in accordance with M.P. 8.
48
M.P. 10 Crankshaft
Required Tools
Refer M.P. 1, 2, 3, 6, 8 & 9

A.
Description
The crankshaft is constructed of forged steel with an internal passage for lubrication of the
crank pin bearing, piston pin bearing and cylinder liner. Removal of the crankshaft is under
taken from the oil pump side of the compressor.
B.
a)
b)
c)
d)
e)
f)
g)
h)
Removal
Remove each cylinder cover in accordance with M.P. 1.
Remove the suction and discharge assemblies in accordance with M.P. 2.
Remove the piston / liner assemblies in accordance with M.P. 3 & 4.
For RM, AM type compressors remove the motor rotor assembly.
Remove the mechanical seal assembly in accordance with M.P. 6.
Remove the oil pump assembly in accordance with M.P. 8.
Remove the rear bearing assembly (casing rear cover) in accordance with M.P. 9.
Support the crankshaft and withdraw through the rear casing using extreme care not to damage the
bearing surfaces.
C.
a)
b)
c)
d)
Inspection
Remove oil passageway plugs and clean the crankshaft with new kerosene.
The crankshaft is factory balanced and the bolts should not be tampered with.
Refit the oil passageway plugs.
Examine the crankshaft journals for signs of excessive wear and damage (scoring and pitting etc.).
Should excessive wear be suspected (greater than 0.006 - 0.15 mm) consult the factory for
dimensional data, tolerances and the appropriate repair method.
e) Repair methods include:
Over-sized bearings, (0.01 0.02, 0.25mm & 0.5mm)
Rebuilding the journal with spray metal and polishing.
Note: This procedure should not be attempted without prior consultation.
D. Refitting
a) Lubricate the front bearing and mating surface of the crankshaft.
b) Support the crankshaft and insert through the rear casing exercising extreme caution not to damage
the bearing surfaces.
c) Fit the rear bearing assembly (casing rear cover) in accordance with M.P. 9.
d) Refit the oil pump assembly in accordance with M.P. 8.
e) Refit the mechanical seal assembly in accordance with M.P. 6.
f) Refit the piston / liner assemblies in accordance with M.P. 3 & 4.
g) Refit the suction and discharge valve assemblies in accordance with M.P. 2.
h) Refit the cylinder covers in accordance with M.P. 1.
i) For RM, AM type compressors refit the motor rotor assembly.
49
50
M. P. 11 Oil Pressure Regulating Valve

Associated Instructions Refer 2.2, 2.3, 2.5, 2.6, 2.7 & 3.2
Required Tools
A.
Description
Located to the right of the oil pump on the rear casing the valve comprises a piston, spring,
spindle and a hand wheel for adjustment purposes (Fig. 31). Turning the hand wheel
clockwise increases oil pressure, while anti-clockwise rotation decreases oil pressure.
B.
b)
c)
d)
e)
f)
Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Close the suction and discharge stop valves, including intermediate valves (if applicable).
Vent the compressor until equal with atmospheric pressure.
Isolate the compressor power supplies with the appropriate lock out tag out method.
Remove the four mounting bolts.
Remove the valve from the casing.
C.
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
Inspection
Remove the spring and valve seat from the body.
Using a parallel punch lightly tap the spring clip from the hand wheel and remove the hand wheel.
Remove the spindle by rotating anti-clockwise.
Remove the valve bonnet.
Clean and examine the components for scoring or spring distortion.
Replace the spring, Teflon O-ring and Teflon packing as required.
Refit the valve spindle.
Refit the valve bonnet.
Align the hand wheel on the stem and insert the spring clip.
Insert the spring and valve seat.
D.
a)
b)
c)
d)
Refitting
Refer: 2.7, 2.2 & 2.3
Mount the valve on the casing with a gasket and the four attachment bolts.
Tighten the attachment bolts evenly to ensure the valve seat remains correctly located.
Exercise the valve to ensure a smooth operation.
Using the correct procedure restart the compressor.
51
M. P. 12 Oil Return Valve

Required Tools
A.
Description
The oil return valve is fitted to two stage compressors only and the purpose of the valve is to
return oil from the high side suction casing to the crankcase (fig 32). The valve is normally
closed and should only be opened for a few seconds periodically during compressor operation.
B. Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Note: Unless abnormally high pressure is observed in the lower casing (with the valve fully closed),
valve maintenance is not required.
a) Isolate the compressor both mechanically and electrically.
b) Close the suction and discharge valves, including intermediate valves (if applicable).
c) Vent the compressor internal pressure using the correct procedure.
d) Disconnect the external drainpipe from the valve and casing.
e) Remove the valve from the casing.
C.
a)
b)
c)
Inspection
Remove the valve bonnet, withdraw the valve stem and clean the valve with new kerosene.
Examine the Teflon seat and replace as required.
Insert the valve stem and install the valve bonnet.
D.
a)
b)
c)
d)
Refitting
Refer: 2.7, 2.2 & 2.3
Refit the valve to the casing.
Reconnect the external drainpipe.
Ensure the valve is fully closed.
52
M. P. 13 Oil Screen and Oil Filter

Required Tools
NOTE: Oil filter is an optional accessory.
A.
Description
The oil screen is located internally in the lower casing or in an additional oil tank located
below the casing for marine type compressors. The screen can be accessed by removing the
external cover plate and pump oil feed pipe for land and marine type compressors or through a
side cover for land type compressors only. The screen is removable and is designed to protect
the oil pump, therefore should be cleaned on a regular basis. The oil filter, located in the
system after the oil cooler is of spacer and filter plate type with a removable drain plug in the
bowl. The plates must be rotated two to three times per week by operating the bar handle
located on the filter cover assembly to remove embedded foreign particles.
B. Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Oil Screen
d) Remove the four bolts from the oil pump flange.
e) Place a receptacle below the oil screen cover plate and remove the four locating bolts.
f) Remove the cover plate with the screen attached.
g) Allow the oil to drain into the receptacle.
Oil Filter
b) Close the suction and discharge valves.
d) Remove the drain plug and drain the oil into a receptacle.
e) Remove the four bolts, which secure the filter bowl to the cover assembly.
f) Remove the filter bowl and retain contents for examination purposes.
C. Inspection
Oil Screen
a) Detach the screen from the cover plate by anti clockwise rotation.
b) Clean the screen with new kerosene and examine the residue for foreign particles.
c) Dry and examine the screen for penetrations to the screen material, replace as required.
d) Refit the screen to the cover plate.
Oil Filter
a) Place a receptacle below the screen plates containing clean kerosene.
b) Clean the plates using a soft brush.
c) Dry the plates and examine any residue for foreign particles.
d) Clean and dry the filter bowl, examine the kerosene for foreign particles.
e) Refit the drain plug to the bowl.
D. Refitting
Refer: 2.7, 2.2 & 2.3
Oil Screen
a) Fit a replacement gasket to the screen cover plate and insert the screen assembly into the casing.
b) Fit a replacement packing to the flange assembly.
c) Fit the four locating bolts to the pump flange and tighten.
d) Fit the four locating bolts to the cover plate and tighten.
53
e) Replenish the oil system as required.

f) Using the correct procedure restart the compressor.
g) Perform a leak check on the cover plate gasket.
Oil Filter
a) Fit a replacement gasket to the filter bowl and partially fill the bowl with new lubricating oil.
b) Fit the bowl to the cover assembly with the four bolts and tighten.
c) Replenish the oil system as required.
d) Using the correct procedure restart the compressor.
e) Perform a leak check on the filter assembly.
54
M. P. 14 Oil Cooler
Required Tools
A.
Description
Two different types of oil coolers may be installed, water cooled (Fig. 33) and refrigerant
cooled (Fig. 34). Water type coolers are of the annular coil in shell type and can be readily
maintained; oil passes through the coil and water around the shell. The refrigerant type cooler
is of the double shell type, oil flow is between the inner and an outer shell; refrigerant is
evaporated in the inner shell to cool the oil. The refrigerant type oil cooler is maintenance free
apart from external inspection but must be operated under strict conditions, which are
explained later in this M.P. under Handling Precautions Refrigerant Type Oil Cooler.
B. Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Water Cooled Oil Cooler
d) Isolate the water supply and remove the drain plug to drain the water.
e) Disconnect the water supply and return pipes.
f) Disconnect the oil inlet and outlet pipes.
g) Remove the oil cooler from the mounting structure.
C. Inspection
Water Cooled Oil Cooler
a) Remove the oil outlet-securing nut.
b) Remove the flange bolts.
c) Withdraw the flange and coil assembly from the shell.
d) Clean using a non-abrasive method and examine the coil.
e) Clean and examine the shell.
f) Replace as required the rust preventative plug (magnesium for fresh water and zinc for seawater).
g) Fit a replacement gasket to the flange and install the coil assembly.
h) Fit a replacement packing to the coil and fit the oil outlet-securing nut.
i) Fit the water drain plug.
55
D.
a)
b)
c)
d)
e)
f)
g)
Refitting
Refer: 2.7, 2.2 & 2.3
Install the cooler on the support frame and secure.
Connect the oil inlet and outlet pipes.
Connect the water supply and return pipes.
Re-establish the water-cooling system supply.
Replenish the oil system as required.
Perform a leak check on oil and water connections.
E. Handling Precautions Refrigerant Type Oil Cooler

a) Ensure a refrigerant supply is maintained during compressor operation, refrigerant isolate valves
should be open.
b) Ensure correct adjustment of the expansion valve to prevent liquid carry-over. Suction pipe
routing to a remote location from the compressor is desirable, however for two stage compressors
the outlet pipe should be connected to the intermediate cooler. With multiple compressor systems
special care should be taken when suction pressure is varied due to the change in number of
operating compressors.
c) Due to the filtration characteristics of the thermostatic expansion valve strainer regular cleaning is
required, as a decrease in refrigerant flow will lead to an increase in oil operating temperature.
d) Correct sizing of the thermostatic expansion valve is essential, as liquid carry-over is liable to
occur due to lag on starting leading to the valve over-opening.
e) Careful adjustment of the control valve is required to ensure that the evaporating temperature does
not go below -40F (-40C), as the cooling effect will be reduced due to increased oil viscosity.
f) Refrigerant feed to the cooler must cease while the compressor is stopped, care should be taken to
ensure that no leakage across the solenoid occurs, that refrigerant is not drawn and evaporated by
parallel running compressors, as this will lead to high oil viscosity due to low oil temperature. Due
to the increased oil viscosity and the increased resistance to flow, an increased wear rate of
compressor components is possible which, could ultimately lead to premature failure of the
compressor. Careful monitoring of the oil pressure is recommended.
g) A decrease in the coolers performance (high oil temperature) is likely if oil accumulates in the
refrigerant side, therefore draining of the oil is to be performed on a regular basis by opening the
valve on the cooler for a short period.
h) In order to prevent super cooling of the oil and overcharging of refrigerant while the compressor is
stopped due to possible leakage of the solenoid valve, open slightly the outlet valve. When the
compressor is to be started ensure the outlet valve is opened fully but monitor the system for
indications of liquid carry-over.
56
M. P. 15 Crankcase Heater
Required Tools
A.
Description
The crankcase heater is fitted in the lower casing (standard for R22 applications, may be an
option on some R717 applications) and is of the screw plug type, available in either 110V,
115V, 220V or 230V (other voltage applications are available on request) at a rating of 200W.
The heater should be energized while the compressor is stopped to maintain the oil at a
suitable temperature and de-energized while the compressor is operating; this is particularly
relevant in cold climates.
NOTE:
During periods of maintenance the electrical supply to the heater must be isolated to
prevent personal injury or damage to the heater, this is particularly relevant when oil changes or
work in the lower casing are in progress.
B.
a)
b)
c)
d)
e)
f)
Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Vent the compressor internal pressure using the correct procedure.
Drain the lubricating oil from the crankcase.
Remove the junction box cover and disconnect the heater power supply cables.
Unscrew the heater from the casing.
C.
a)
b)
c)
Inspection
Examine the power supply cables for signs of damage or deterioration.
Examine the casing and probe for signs of damage or overheating.
Perform a resistance check.
D.
a)
b)
c)
d)
e)
Refitting
Refer: 2.7, 2.2 & 2.3
Refit the heater to the casing.
Reconnect the power supply cables and fit the junction box cover.
Refill the crankcase to the correct level with lubricating oil.
Perform a leak check on heater crankcase connection.
57
M. P. 16 Suction Gas Strainer

Required Tools
A.
Description
The suction gas strainer is located below the suction valve on single stage compressors, with
an additional strainer fitted below the high stage suction of a compound compressor. Access to
both is under taken in the same manner and for the initial compressor or system run in period
the strainers are wrapped in cloth which is secured by steel wire.
B.
a)
b)
c)
d)
e)
Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Vent the compressor internal pressure using the correct procedure.
Remove the cover plate.
Extract the strainer.
C.
a)
b)
c)
d)
Inspection
Should the strainer is fitted with a cloth wrap, remove the cloth.
Examine the cloth and strainer for foreign material.
Examine the strainer for penetrations to the screen material.
Replace as required the cloth wrap and secure with steel wire.
D.
a)
b)
c)
d)
Refitting
Refer: 2.7, 2.2 & 2.3
Insert the strainer.
Fit the cover plate using a replacement gasket.
Perform a leak check on the cover plate.
NOTE:
This procedure is applicable to the high side strainer.
58
M. P. 17 Safety Valve, Pressure Gauge and Pressure Switch

Required Tools
A. Description
Safety Valve
A safety valve is fitted to the discharge side of a compressor and to the low stage discharge of
a compound compressor. The valve operating pressure is preset and no field adjustment is
possible, each valve has a date stamp attached and this should be monitored for in service life.
Pressure Gauge
A pressure gauge is fitted to each service valve to permit recording of operating data. The
gauges are glycerin filled and should be monitored for leakage and excessive pointer vibration
as this will lead to incorrect readings.
Pressure Switch
Pressure switches are of the electro-mechanical type and should be monitored for leakage. In
addition regular checks should be performed to ensure that the switches continue to operate at
the desired settings.
B. Removal
Refer: 2.5, 2.6, 2.7 & 3.2
Safety Valve
d) Remove safety valve complete with mounting flange.
Pressure Gauge and Pressure Switch
b) Close the appropriate service valve.
c) Release pipeline pressure at an adjacent fitting.
d) Disconnect the pressure switch electrically.
e) Disconnect the gauge / switch from the pipe.
f) Remove from the panel.
C. Refitting
Refer: 2.7, 2.2 & 2.3
Safety Valve
a) Fit a replacement valve to the mounting flange.
b) Using a replacement gasket fit the safety valve assembly.
c) Using the correct procedure restart the compressor.
d) Perform a leak check on the cover plate.
Pressure Gauge and Pressure Switch
a) Fit a replacement gauge / switch to the panel.
b) Connect pressure pipe.
c) Reconnect the pressure switch electrically.
d) Open the service valve and purge the pipe through an adjacent fitting to the gauge / switch.
e) Set the pressure switch using certified test equipment.
g) Perform a leak check on the appropriate fittings.
59
M. P. 18 V Belt Drive
Associated Instructions Refer 3.2
Required Tools
A.
Description
The compressor and motor may be equipped with either C or D section sheaves and belts,
refer to the equipment specification manual. The belt guard and front panel must be fitted at
all times when the compressor is operational to reduce the risk of personal injury. The
compressor or motor sheaves may have more grooves than the number of belts, refer to the
equipment specification manual and always leave the empty grooves at the furthest point from
the compressor and motor.
B.
a)
b)
c)
d)
e)
Removal
Remove the belt guard front panel.
Release the belt tension.
Remove the belts.
C. Inspection
a) Examine the drive belts for signs of cracking, fraying, uneven wear and contamination.
b) Examine the sheaves for signs of uneven or excessive wear, cracks and damage.
D.
a)
b)
c)
Refitting
Fit the belts.
Re-tension the belts.
Check the compressor and motor sheaves for correct alignment across the face closest to the
compressor and motor.
d) Refit the belt guard front panel.
g) If replacement belts have been fitted re-check belt tension after a short operational period.
60
M. P. 19 Coupling Drive
Required Tools
A.
Description
Two types of direct drive coupling may be used either the CA type (Fig. 35) or CG type (Fig.
36), both types are subject to critical alignment tolerances.
B. Removal - General
c) Remove the coupling guard.
CA coupling
a) Remove coupling bolts (Fig. 35 [1 & 2]).
b) Screw bolts in to the motor side flange to separate flange and spacers [4].
c) Remove the tire. Should the tire be adhered to the flanges on either side it may be necessary to
repeat operation b) above from both sides.
CG Coupling
a) Tighten the outer circle of rubber block (Fig. 36 [1]) with the attached steel strap [2].
b) Release the setting bolts (M30) and remove rubber block. Do not slacken the steel strap at this
point.
C. Inspection
a) Examine coupling for signs of distortion, cracking and fraying.
b) The life expectancy of a coupling is affected by the amount of misalignment, therefore refer to
Table 13 (Fig.37) for tolerances.
Deflection of outer circle in. (mm)
Deflection face to face in. (mm)
Distance face to face in. (mm)
Table 13
CA Type
0.008 (0.2)
0.004 (0.1)
5.433 5.512 (138 140)
CG Type
0.008 (0.2)
0.004 (0.1)
6.260 6.338 (159 161)
61
D. Refitting
CA Coupling
a) Insert the rubber tire, locate the flanges and insert the bolts.
b) Tighten bolts in accordance with manufactures data sheet.
CG Coupling
a) Insert the coupling and tighten setting bolts.
b) Slacken the steel strap in accordance with the manufactures data sheet.
General
a) Fit the coupling guard.
b) Using the correct procedure restart the compressor.
NOTE:
Bolts should be re-tightened two weeks after initial installation, there after every six
months and at each scheduled maintenance.
62
M. P. 20 Flanged Motor Assembly

Required Tools
A.
Description
The motor is of the open drip proof squirrel cage type and is constructed with two principal
components, the rotor assembly which attaches directly to the crankshaft and the stator
assembly which forms part of the outer casing, which bolts directly to the compressor casing.
Airflow is induced through the motor end plate and around the stator assembly for cooling
purposes, before being expelled through the motor casing. To gain access to the compressor
mechanical seal assembly it is necessary to remove the end plate and rotor assembly.
B.
Removal
1
Cover Plate Removal
2
Bearing Removal
Motor Bearing
a) Remove the four bolts (M12) from the end cover.
b) Attach guide bolts to the two upper locations of the end cover.
c) Fit to the left and right tap holes bolts and tighten equally to remove the end cover.
d) Should the bearing remain on the shaft, fit the removal tool (Fig. 38) and ease the bearing from the
shaft.
e) Should the bearing be removed with the end cover (Fig. 39) then use a hexagonal bolt to push the
bearing from the housing applying the force to the outer ring only.
63
3
End Shaft Removal
4
Motor Rotor Removal
Motor Rotor
a) Remove the rear cover as described above.
b) Remove the end-shaft with the rear bearing using extreme caution to prevent bearing damage.
c) Remove the crankshaft key support plate and attach the motor rotor guide to the crankshaft (Fig.
40).
d) Using the ancillary tool attach two bolts (M12) to the spider and fit the draw-out plate to the motor
rotor guide and set nuts on bolts (M12).
e) Tighten the extractor nuts equally to ease the motor rotor along the shaft and then pull the bolts
(M12) to remove the rotor assembly complete.
Note: Extreme care must be taken to avoid damage to the aluminum fins during the removal process.
5
Rotor Removed
6
Shaft Extension Fitted
Shaft Extension Removed
64
C. Inspection
a) Perform the appropriate cleaning and inspection process as directed by the motor maintenance
procedure supplied by the motor manufacturer.
D. Refitting
Motor Rotor
a) Refitting of the rotor assembly is the reverse of the removal process.
b) The position of the crankshaft key should be noted prior to installation.
Motor Bearing
a) Refitting of the rear bearing is the reverse of removal process, using the ancillary tool to set the
bearing correctly on the shaft (Fig. 41).
b) Refit the rear cover and fit securing bolts.
65

Ref Compressor HASEEGAVA PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Ref Compressor HASEEGAVA PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ref Compressor HASEEGAVA PDF

Uploaded by

Copyright:

Available Formats

VK / VKL

Safety Instructions & Guidelines

Preparation for operation

3. CONSTRUCTION, MAINTENANCE and INSPECTION

Compressor serial number

Hasegawa Refrigeration Ltd. provides

Daily Inspection & Maintenance

Crankcase, Cylinder Covers and Principal Components

Piston Pin Plain Bearings

Piston Pin Needle Roller Bearings

Crank Pin Bearings

Oil Pressure Regulating Valve

Oil Lubrication System

Mechanical Shaft Seal

Suction Gas Strainer

Suction and Discharge Valve Plates

High and Low Pressure Switches

Oil Protection Switch

Safety Relief Valve

Single Stage Compressor

Model number: VK(L)42RM

These compressors comprise a considerable number of common and interchangeable

1.3 Operational Limits

Below: 255 psig (R717) 312 psig (R22)

1.4 Specification, Refrigeration Capacity and Required Power

RM, AM Type Motor

Rated speed (rpm)

Prior to initial start-up and after a long period of standstill the

Air compression must be avoided, with the exception of post

Sheaves are to be correctly aligned and belts are to be correctly

Prior to pressure / vacuum testing cotton cloth is to be wrapped around

6. Oil return valve

The oil return valve of a compound compressor must be fully closed

2.1 Preparation for Operation

2.3 Operational and Inspection Criteria

Minimum pressure 22 psi (1.5kg/cm)

18 to 36F (10 to 20C) of superheat is recommended for suction temperature.

2.4 Compressor Shutdown

2.5 Extended Period of Shutdown

2. Perform a system refrigerant leak check.

2.6 Operation of the Compressor Prior and Post Maintenance

2.7 Action to Prevent Liquid Carry-over

2.8 Fault Diagnosis and Rectification

D. Motor stops after 45

OPS and HPS are not reset.

Investigate and reset as required.

Belts too tight.

A. Suction pressure does

B. Discharge pressure too

C. Suction pressure too

Investigate and clean.

7. Defrost and monitor.

A. Oil pressure too low.

B. Oil pressure gauge

Inadequate water supply.

Increase water supply and examine tubes.

Investigate and replace.

4. Investigate and clean.