Design Features and
Operation of Jet Ejectors
Jet Ejectors
The term jet ejector describes a device in
which a pumping effect is achieved using a
motive fluid. A jet ejector requires no mechanical drive and has no moving parts. This basic
principle applies to every jet ejector in different
models and ranges of application. The application determines the design of the flow section.
A steam jet ejector is illustrated below as example (steam serves as motive fluid to create
vacuum). The function depends, above all, on
the design of the motive nozzle (2) and of the
diffuser (4 + 5). The motive fluid passes successively through these two components.
The flow section will change along this path.
The pressure in the motive nozzle (2) decreases
and the velocity rises. Conversely, the flow is
decelerated in the diffuser (4 + 5) while its pressure increases to the discharge pressure at the
outlet of the jet ejector.
The section between motive nozzle (2) and
diffuser (4 + 5) has the lowest static pressure,
approximately equivalent to the suction pressure ps. At this point the suction flow enters
into the ejector head (3) through the suction
connection B and is mixed with the motive fluid
flowing with high velocity. Part of the kinetic
energy is transferred to the suction flow. Motive
motive steam at pressure ptr
A
flow and suction flow pass together - as a mixture - through the diffuser, loosing velocity and
gaining pressure. The increase from suction
pressure ps to discharge pressure pd corresponds to the delivery head for the suction flow
or to the pressure difference of the jet ejector.
The ratio pd / ps is the compression ratio of a jet
ejector.
ln a jet ejector the static pressure energy of the
motive flow which cannot be directly transferred
is thus converted into kinetic energy. This kinetic energy can be released to the suction flow
by impulse transfer while both flows mingle.
The diffuser converts the kinetic energy of the
mixture consisting of motive flow and suction
flow back into static pressure energy.
ln the steam jet vacuum ejector illustrated
below, the critical pressure ratio is exceeded
in the motive nozzle (2) (this can be recognized
by the expansion of the nozzle cross-section
downstream the minimum throat diameter.)
The steam velocity exceeds the sonic velocity
accordingly. Motive flow and suction flow are
mixed at supersonic velocity and then decelerated to the sonic velocity upon reaching the
diffuser throat. ln the diverging section of the
diffuser, the pressure finally increases to the
discharge pressure pd.
(2) motive nozzle
(3) head
(1)
steam chest
with strainer
(5)
outlet diffuser
C
inlet diffuser
(4)
B
suction flow at pressure ps
mixed flow at pressure pd
sunderdiek.de
Types and Designations
of Jet Ejectors
Jet ejectors are used to create vacuum, to
compress gases, to convey liquids, to transport granular solids, to mix liquids or gases.
The motive fluid may be:
steam at pressure above atmosphere
atmospheric steam*)
vacuum steam*)
compressed gas or air
atmospheric air
water or other available liquids
*)
The following table summarizes the terms of
jet ejectors laid down according to DIN standards 24290. When defining certain types of
jet ejectors, the standard terms for motive fluid and material delivered (gas, steam, liquid,
solids) can be replaced by specific ones.
motive medium
contributing
to designation
provided that the discharge
pressure of the jet ejector
or ejector stage in question
is low enough.
Example:
A liquid jet solids ejector using water as
motive fluid to convey gravel can be
designated as water jet gravel ejector.
gas jet
ejector
steam jet
ejector
liquid jet
ejector
gas jet
ventilator
steam jet
ventilator
liquid jet
ventilator
jet
compressor
gas jet
compressor
steam jet
compressor
(steam jet
vapour compressor)
liquid jet
compressor
jet vacuum
ejector
gas jet
vacuum ejector
steam jet
vacuum ejector
liquid jet
vacuum ejector
jet
liquid ejector
gas jet
liquid ejector
steam jet
liquid ejector
liquid jet
liquid ejector
jet
solids ejector
gas jet
solids ejector
steam jet
solids ejector
liquid jet
solids ejector
jet
jet
gas ejector ventilator
Krting Hannover AG
Badenstedter Strae 56
30453 Hannover
Germany
Tel.: + 49 511 21 29-0
Fax: + 49 511 21 29-223
E-Mail: st@ koerting.de
www.koerting.de
000-DVP-EN-140312
suction medium
contributing
to designation
