427

A publication of

CHEMICAL ENGINEERING TRANSACTIONS

VOL. 37, 2014
Guest Editors: Eliseo Ranzi, Katharina Kohse- Hinghaus
Copyright 2014, AIDIC Servizi S.r.l.,
ISBN 978-88-95608-28-0; ISSN 2283-9216

The Italian Association

of Chemical Engineering
www.aidic.it/cet
DOI: 10.3303/CET1437072

Hybrid Route to Produce Acrylic Acid from Sugarcane

Molasses
John H. Bermudez Jaimesa, Bruna T. Da Silvaa, Jaiver E. Jaimes Figueroaa,
Betnia H. Lunellia, Rubens Maciel Filhoa, Maria R. Wolf Maciela, Augusto T.
Moritab, Paulo. L. A. Coutinhob
a

Laboratory of Optimization, Design and Advanced Control, School of Chemical Engineering, State University of
Campinas, Av. Albert Einstein 500, CEP 13083-862 Campinas, Brazil.
b
BRASKEM, Av. das Naes Unidas 4777, 11th floor, CEP 05477-000 So Paulo, Brazil.
[email protected]

This work presents the synthesis of acrylic acid by hybrid route from sugarcane molasses fermentation
and later acid lactic dehydration. Lactic acid was produced by sugarcane molasses fermentation using the
Lactobacillus plantarum CCT 5731 bacteria in bioreactor BioFlo 415 at 37 C. After of 46.4 h of
fermentation 50.6 g/L of lactic acid was obtained with productivity of 1.1 g/L.h which was subsequently
concentred to 152 g/L and stored to dehydration stage. Both commercial lactic acid and lactic acid
obtained through fermentation stage were dehydrated by catalysts supported on basic zeolite (NaY) in a
tubular reactor at 300 C and continuous flow of CO2 (30 mL/min). The largest selectivity (25.7 %) for
acrylic acid was obtained when the commercial lactic acid and KBr/NaY were used. When lactic acid
obtained by fermentation a maximum acrylic acid selectivity of 16.7 % was achieved using KI/NaY. All
chemicals species were characterized by high performance liquid chromatography (HPLC).

1. Introduction
In recent decades, biomass has played an important role in the industry especially for its abundance and
relative low cost (Lee et al. 2010). In Brazil, the sugarcane is used to sugar and ethanol production (Dias
et al. 2013). In the purification of sugar is obtaining a sub-product know as sugarcane molasses (Chauhan
et al. 2011), which is a brownish viscous that is generally used in the production of ethanol (Ghorbani et al.
2011). However, the sugarcane molasses is a carbon source ideal for the production of small molecules
such as lactic acid by fermentation route. Lactic acid has shown great importance in the food industry,
textile, leather, pharmaceutical (Rojan et al. 2009). This is a highly reactive molecule that may be reactant
in reactions of dehydration, decarboxylation, condensation, reduction, dehydrogenation, esterification and
polymerization that means a potential feedstock for renewable chemicals (Zhang et al. 2008). From
dehydration of lactic acid may be produced the acrylic acid (Yan et al. 2011), which is nowadays mainly
produced by oxidation of propylene in the petrochemical industry and used as raw material in the
production of polymeric products (Lee et al. 2010). These polymers are characterized by their
transparency, easy adhesion, elasticity, and stability to heat and to light. They are applied to the coating of
surfaces, textiles, adhesives, paper treatment, fibers, detergents, superabsorbent materials, etc (Xu et al.
2011). On the other hand, acrylic acid production by fermentative process present an innovative process of
great importance, because the possibility of low cost for its production and because of a renewable raw
material (Lunelli et al. 2007). However, this last route is under study and some improvements are needed
to become economically competitive.
In this context, the present work aims to develop the synthesis of acrylic acid by hybrid route
(fermentation-catalytic dehydration) from of sugarcane molasses fermentation and subsequently catalytic
dehydration of lactic acid to obtain as final product acrylic acid, highlighting the use of sugarcane molasses
as a promising raw material to the chemical production with high added value.

Please cite this article as: Bermudez Jaimes J.H., Torres Da Silva B., Jaimes Figueroa J.E., Lunelli B.H., Maciel Filho R., Wolf Maciel M.R.,
Morita A.T., Coutinho P.L.A., 2014, Hybrid route to produce acrylic acid from sugarcane molasses, Chemical Engineering Transactions,
37, 427-432 DOI: 10.3303/CET1437072

428

2. Experimental
2.1 Materials
Sugarcane molasses was donated by Usina Iracema, a large scale industrial plant and Lactobacillus
plantarum bacteria was purchased from Andr Tosello Foundation. Catalysts were prepared through a
confidential procedure and the commercial DL-lactic acid (~ 90 %) was acquired of Sigma-Aldrich.
2.2 Sugarcane molasses fermentation to obtain lactic acid
Sugarcane molasses fermentation was divided in two steps: studies in Shaker and fermentation in
laboratory scale. Previous studies in shaker were performed to determine the working conditions (sucrose
concentration, yeast extract concentration and temperature) to be implemented in a bioreactor BioFlo 415.
Lactobacillus plantarum bacterium was reactivated in ManRogosaSharpe (MRS) agar for 48 h at 28 C.
After this time, an aliquot was transferred to a test tube containing 10 mL of MRS liquid medium and
maintained for 48 h growth temperature. Thereafter, 5 mL tube were removed and added to 125 mL
Erlenmeyer flask with 45 mL of MRS liquid medium and again held under the same conditions for 48 h. In
the final step, 300 mL of sugarcane molasses were prepared in Erlenmeyer with 14 % v/v inoculum and
known concentrations of sucrose (14 g/L, 23 g/L and 33 g/L) and extract yeast (2 g/L, 4 g/L and 6 g/L).
Hence, fermentations at 31 C, 34 C and 37 C were carried out for 24 h and 200 rpm. Then, 4 mL
samples were collected at 6 h, 10 h and 24 h to monitor the process and the lactic acid and sugars
(fructose, glucose and sucrose) were characterized using a high performance liquid chromatography,
Agilent 1260, equipped with a refractive index detector and a Bio-Rad Aminex HPX-87H column (3007.8
mm) at 25 C, and 4mM H2SO4 was used as mobile phase at a flow rate of 0.6 mL/min and sample
injection volume of 15 L. Identified the best conditions of sucrose and yeast extract concentration and
temperature, the fermentation was conducted in a bioreactor BioFlo 415 of 7 L. This step began with the
preparation of the cultivation in the conditions used in the first three step of culture growth studies carried
out in shaker level. Then, the contents of the Erlenmeyer flask (50 mL ) was added to another 1000 mL
Erlenmeyer flask containing 450 mL of MRS liquid medium and kept on shaker for 30 h, at optimal
temperature. Finally, 2,580 mL of sugarcane molasses composed of the best conditions of sucrose and
yeast extract were added to the bioreactor and 150 mL of water ware also added. Then, the above mixture
was sterilized at 121 C for 30 min. After cooling, 420 mL of inoculum was added to the bioreactor and the
fermentation was carried out to 200 rpm and temperature determined in previous studies. During the
fermentation the pH was kept to 5 by addition of 4N NaOH solution and a pulse of sugarcane molasses
solution was given in time where the pump power of the base (4N NaOH) stopped working (24.2 h) and
the fermentation was maintained for 46.4 h. Subsequently, the biomass was characterized by gravimetric
method and the lactic acid and sugars were characterized by HPLC using a methodology described
above.
2.3 Catalytic dehydration of lactic acid to acrylic acid
The dehydration of both commercial and lactic acid obtained from fermentation of sugarcane molasses
(Figure 1) to produce acrylic acid over the catalysts supported on basic zeolite (KBr/NaY, KI/NaY and
Ca3(PO4)2/NaY) and the support (modified NaY) were carried out in a fixed-bed reactor of 0.1075 m inner
diameter and 0.130 m of length. The catalyst (2.24 g) was placed in the middle of the reactor and quartz
wool was placed in both ends (bottom 1.16 g, top 2.24 g) and pre-treated at 573 K for 0.5 h under Ar
3
(0.0018 m /h). The feedstock (lactic acid solution, 152 g/L) was pumped into the preheating zone (LHSV =
1
3 h ) and driven through the catalyst bed by CO2. The liquid products were condensed and collected
every 0.33 h. Then, the concentration of lactic, acetic, propionic and acrylic acids were measured by HPLC
at 30 C and using the methodology described to sugar analysis.

Figure 1. Lactic acid. a) Commercial, b) obtaining by fermentation of sugarcane molasses

429

The selectivity and conversion were calculated according to the equations 1 and 2.
Conversion of lactic acid =

Selectivity =

molar quantity of lactic acid that reacted

x100
molar quantity of lactic acid feed to reactor

(1)

carbon molar quantity of the final product

x100
molar quantity of lactic acid that reacted

(2)

3. Results and discussion

3.1 Sugarcane molasses fermentation
From studies in shaker was determined that, in the considered conditions, the highest concentration of
lactic acid (11.5 g/L), after 24 h of fermentation, was obtained with 37 C, 33 g/L of sucrose and 4 g/L of
yeast extract. Therefore, in the fermentation of sugarcane molasses in bioreactor BioFlo 415 these
conditions were maintained and its results are show in the Figures 2 and 3. A priori of fermentation, the
sugarcane molasses was autoclaved in the bioreactor BioFlo 415. This bioreactor model presented fluid
loss during autoclaving for which reason 150 mL of water ware increased to correct this loss. However, the
increased volume of water was greater than the volume of fluid lost, whereby the sugarcane molasses
solution presented dilution at the start of fermentation. Next to 22 h of fermentation, it was observed that
NaOH feeding pump was not working for which was decided to give a pulse of sugarcane molasses
solution (223.6 g/L of sucrose) at 24 h. The measure of sugars in HPLC showed that just before of pulse
the fructose, glucose and sucrose had been almost completely degraded obtaining a concentration of
lactic acid of 40.9 g/L. After the pulse was possible to increase the concentration of lactic acid, obtaining a
maximum concentration of lactic acid of 50.6 g/L at 46.4 h of fermentation and low concentration of sugars
(1.1 g/L of fructose, 0.1 g/L of glucose and 0.1 g/L of sucrose) (Figure 2). Moreover, the higher productivity
was of 2.9 g/L.h at 9.8 h of fermentation and decrease to 1.1 g/L.h at 46.4 h. Biomass concentration
suffered rapid increase during the first 9.8 hours of fermentation and then fluctuated around 3 g/L.

Concentration (g/L)

50
40
30
20
10
0
10

20

30

40

Productivity (g/L.h)

Biomass (g/L)

0
0

10

20

Time (h)

30

40

Figure 2. Sugarcane molasses fermentation by Lactobacillus plantarum. Biomass, Fructose, glucose,

lactic acid, productivity, sucrose

430

3.2 Catalytic dehydration of lactic acid

The results of catalytic dehydration of both commercial lactic acid and lactic acid obtaining by sugarcane
molasses fermentation are showed in the Figure 3.
Obtaining lactic acid - Modified NaY
100

20

80

20

80

15

60

15

60

10

40

10

40

20

20

0
0.0

0.5

1.0

1.5

2.0

2.5

3.0

0.0

0.5

1.5

2.0

2.5

3.0

Obtaining lactic acid - KBr/NaY

100

20

80

20

80

15

60

15

60

10

40

10

40

20

20

0
0.0

0.5

1.0

1.5

2.0

2.5

3.0

Conversion (% mol)

25

Selectivity (% mol)

100

0.0

0.5

Commercial lactic acid - KI/NaY

1.0

1.5

2.0

2.5

3.0

Obtaining lactic acid - KI/NaY

100

20

80

20

80

15

60

10

40

20

0
0.0

0.5

1.0

1.5

2.0

2.5

15

60

10

40

20

Commercial lactic acid - Ca3(PO4)2/NaY

3.0

Conversion (% mol)

25

Selectivity (% mol)

100

Conversion (% mol)

25

0.0

0.5

1.0

1.5

2.0

2.5

3.0

Obtaining lactic acid - Ca3(PO4)2/NaY

25

100

20

80

20

80

15

60

15

60

10

40

10

40

20

20

0
0.0

0.5

1.0

1.5

Time (h)

2.0

2.5

3.0

0
0.0

0.5

1.0

1.5

2.0

2.5

3.0

Time (h)

Figure 3. Results of the catalytic dehydration of commercial acid lactic and lactic acid obtaining by
sugarcane molasses fermentation. acetic acid, acrylic acid, lactic acid, propionic acid

Conversion (% mol)

100

Conversion (% mol)

25

Selectivity (% mol)

Selectivity (% mol)

1.0

25

Conversion (% mol)

Selectivity (% mol)

Commercial lactic acid - KBr/NaY

Selectivity (% mol)

Conversion (% mol)

25

Selectivity (% mol)

100

Conversion (% mol)

Selectivity (% mol)

Commercial lactic acid - Modified NaY

25

431

These tests were conducted primarily in commercial lactic acid to evaluate the catalysts catalytic activity in
the dehydration of lactic acid because the lactic acid obtained by fermentation of sugarcane molasses has
residual compounds, such as sugars and salts, which can contribute to the catalytic deactivation and
obscure its physical appearance. After each reaction, the condensate was a colorless liquid with a small
immiscible phase in the surface which was identified as 2,3-pentadione by gas chromatography; also
acetaldehyde was identified. Figure 3 depicts the results of selectivity and conversion of the commercial
acid lactic catalytic dehydration (results expressed in molar percentage). Generally, for all reactions, it was
observed a conversion near to 100% with substantial decrease in the selectivity to acrylic acid. The
catalysts support showed selectivity for acrylic acid around 19 % at 16.7 h of reaction and subsequently
deactivation. The KBr/NaY presented higher selectivity to acrylic acid (25.7 %) than the support, but it was
also deactivated. The KI/NaY was not deactivated and presented a selectivity of 16.8 % at 3 h of reaction
and the Ca3(PO4)2/NaY showed a selectivity of 11.3 % to acrylic acid and 6.4 to propionic acid as principal
products. When lactic acid obtained from sugarcane molasses fermentation was used, a considerable
decrease in selectivity for all catalysts was obtained, as expected (Figure 3). Of all used catalyst, the
KI/NaY showed the best results with selectivity for acrylic acid of 15.7 % and it was not deactivated during
the 3 h of reaction. The KBr/NaY catalyst that presented the best results for dehydration of commercial
lactic acid was the most affected by the impurities of lactic acid obtaining from fermentation of sugarcane
molasses. This catalyst presented a similar selectivity (less that 6.5 %) to both acrylic acid and propionic
acid. Moreover, the Ca3(PO4)2/NaY presented a slight decrease (0.3 %) in selectivity to acrylic acid (11.0
%), but it was not deactivated during of time of reaction.

4. Conclusions
This work explored the importance of sugarcane molasses as raw material to production of molecules with
high added value that are commonly obtained from fossil fuels sources, as the acrylic acid. Besides
possible improvements in the end product characteristic, the use of renewable feedstock contributes to
many issues regarding environmental concerns.
Lactobacillus plantarum CCT 5731 showed great capacity to metabolize the sugars present in larger
amounts in the sugarcane molasses such as fructose, glucose and sucrose with production of biomass
around 3 g/L.
According to results of dehydration, the KI/NaY catalyst presented good potential for future studies due to
its acceptable selectivity and high resistance to deactivating agents. However, when lactic acid from
fermentation is used is recommended to remove the impurities that may lead to catalyst deactivation.
Acknowledgements
The authors are grateful to the financial support of CNPq and FAPESP trough the grant 2008/06108-0 and
BRASKEM.
References
Chauhan M.K., Chaudhary S., Kumar S., 2011, Life cycle assessment of sugar industry: A review,
Renewable and Sustainable Energy Reviews, 15, 34453453.
Dias M.O.S., Junqueira T., Rossell C., Maciel Filho R., Bonomi A., 2013, Evaluation of process
configurations for second generation integrated with first generation bioethanol production from
sugarcane, Fuel Processing Technology, 109, 84-89.
Ghorbani F., Younesi H., Sari A., Najafpour G., 2011, Cane molasses fermentation for continuous ethanol
production in an immobilized cells reactor by Saccharomyces cerevisiae, Renewable Energy, 36, 503509.
Lee J.M., Hwang D.W., Hwang Y.K., Halligudi S.B., Chang J.S., Han Y.H., 2010, Efficient dehydration of
methyl lactate to acrylic acid using Ca3(PO4)2SiO2 catalyst, Catalysis Communications, 11, 11761180.
Lunelli B.H., Duarte E.R., Vasco de Toledo E.C., Wolf Maciel M.R., Maciel Filho R., 2007, A new process
for acrylic acid synthesis by fermentative process, Appl. Biochem. Biotechnol., 137-140, 487-499.
Rojan J., Anisha G.S., Nampoothiri K.M., Pandey Ashok, Direct lactic acid fermentation: Focus on
simultaneous saccharification and lactic acid production, Biotechnology Advances, 27, 145-152.
Xu Z., Zhu L., Chen, H., 2011, Comprehensive Biotechnology, vol 3: Industrial Biotechnology and
nd
Commodity Products, Acrylic Acid, 2 Ed., Moo-Young M., Ed., Burlington: Academic Press, 201-206.

432

Yan J., Yu D., Sun P.,Huang H., 2011, Alkaline earth metal modified NaY for lactic acid dehydration to
acrylic acid: Effect of basic sites on the catalytic performance, Chinese Journal of Catalysis, 32, 405411.
Zhang J., Lin, J., Cen, P., 2008, Catalytic dehydration of lactic acid to acrylic acid over sulfate catalysts,
The Canadian Journal of Chemical Engineering, 86, 10471053.