MEGATECH DESIGNERS CONSULTANTS INT'L Confidential
BASE PLATE DESIGN
DESIGN CRITERIA
CONCRETE COMP. STRENGTH
B. PLATE YIELD STRESS
COLUMN AXIAL LOAD
COLUMN
WEB DEPTH
WEB THICKNESS
FLANGE WIDTH
FLANGE THICKNESS
R. PLATE THICKNESS
NO. OF RIB PLATE
B. PLATE WIDTH
LENGTH
AREA
PEDESTAL AREA
BEARING
ALLOW. BEARING STRESS
ACTUAL BEARING STRESS
SAFETY FACTOR
BENDING
CRITICAL
BENDING
LENGTHS
(max. of m, n, n')
REQUIRED THICK. OF PLATE
ADOPT
09/06/2016
BP1
fc'
Fy
P
20.70 mpa
248.22 mpa
6.85 kn
d 863.60 mm
tw
17.48 mm
bf 863.60 mm
tf
17.48 mm
tr
20.00 mm
nr
20
B 300.00 mm
N 150.00 mm
A1 45,000 mm2
A2 175,000 mm2
Fp
fp
F.S.
14.29 mpa
0.15 mpa
93.80 OK !
m -335.21 mm
n -195.44 mm
n'
2.51 mm
l
2.51 mm
tp
0.12 mm
2 x 300 x 150 mm BASE PLATE
Page 1
ANCHOR BOLT
DESIGN CRITERIA
BOLT TYPE (A325/A490)
CONNECTION TYPE (FS, FO, FL/B)
FS - friction, standard size
F0 - friction, oversized
FL - friction, long slotted
B - bearing type
TENSILE FORCE
SHEAR FORCE
BOLT
### COMBINED SHEAR & TENSION
ALLOWABLE SHEAR STRESS
ALLOWABLE TENSILE STRESS
AREA OF 1- BOLT
TOTAL BOLT AREA
ACTUAL SHEAR STRESS
SAFETY FACTOR
ACTUAL TENSILE STRESS
SAFETY FACTOR
PULL-OUT
ALLOWABLE BOND STRESS
EMBEDDED LENGTH
#DIV/0!
A325
FS
T
V
1.00 kn
0.00 kn
16 mm
Fv 120.00 mpa
Ft 300.00 mpa
Ab 197.93 mm2
A 1979.30 mm2
fv
0.00 mpa
SF #DIV/0!
ft
0.51 mpa
SF 593.79
U
L
0.83 mpa
634.09 mm
10 - 16 x 635mm A. BOLT
MEGATECH DESIGNERS CONSULTANTS INT'L Confidential
09/06/2016
AB1
REMARK
(Thread
excluded
from shear
plane)
#DIV/0!
OK !
635
10 - 16 x 635mm A. BOLT
Page 2
SUPPORT REACTION
JOINT 1
X
DL
0.00
LL
0.00
WL
0.00
SL
-1.21
LOAD COMBINATION
DL+LL
0.00
0.75(DL+LL+WL)
0.00
0.75(DL+WL)
0.00
0.75(DL+LL+SL)
-0.91
0.75(DL+SL)
-0.91
MAX. COMP.
MAX. TENSION
SHEAR
0.91
JOINT 2
Y
X
32.16 DL
0.00
26.44 LL
0.00
0.00 WL
0.00
216.12 SL
39.53
LOAD COMBINATION
58.60 DL+LL
0.00
43.95 0.75(DL+LL+WL)
0.00
24.12 0.75(DL+WL)
0.00
206.04 0.75(DL+LL+SL)
29.65
186.21 0.75(DL+SL)
29.65
206.04 MAX. COMP.
0.00 MAX. TENSION
SHEAR
29.65
Y
32.16
26.44
0.00
-216.12
58.60
43.95
24.12
-118.14
-137.97
58.60
-137.97
Sheet3
PROJECT: STEEL BUILDING DESIGN CASE STUDY
SUBJECT: Tension member design. Bolted connection.
SHEET 101 of 131
Connection for a 38.3 foot long tension member that has to resist 78 kips of already factored load.
No slip is permitted, so this connection is slip critical.
t = resistance factor relating to tensile strength
Ag = gross cross-sectional area
Ae = U*An
U = reduction coefficient
Fy = specified (ASTM) minimum yield stress
Fu = specified (ASTM) minimum tensile strength
d = diameter of the bolt
An = net area
Rn = strength
Rstr = slip critical strength
Lc = distance from edge of hole to edge of connected part
t = thickness of connected part
Ab = nominal bolt area
Pu = factored load to be resisted
Fv = ultimate shearing strength
= mean slip coefficient (coefficient of static friction)
Tb = minimum fastener tension
Agv = gross area acted upon by shear
Agt = gross area acted upon by tension
Anv = net area acted upon by shear
Ant = net area acted upon by tension
Because the bolt size and layout will affect the net area of the tension member, we will begin with
the selection of the bolts. Use A325 bolts and A572 Grade 36 steel for both the tension member and
the gusset plate (standard holes).
t=
TRY :
3/8
Ab =
0.60
Shear strength:
Rn= Fv Ab
3/4
(in) bolts
(in2)
Pu =
=
Fv =
=
Fy =
Fu =
L=
in
Tb =
Ns =
39
2
(kips) from table J3.1 LRFD
(assuming that the threads are in the shear plane)
Rn=
21.65 Kips/bolt
Page 4
76
0.75
48
0.33
36
58.0
38.3
Sheet3
Rstr = (1.13 Tb b Ns)
Shear strength controls
Rstr =
29.09
Kips/bolt
Rn =
21.65
Kips/bolt
Red font indicates user input
PROJECT: STEEL BUILDING DESIGN CASE STUDY
SUBJECT: Bolted connection
Number of bolts required =
Try =
4
bolts
Minimum spacing :
bolts
the distance between centers of standard, oversized, or slotted holes, shall
not be less than 3d (from AISC J3.3).
s =3 d=
2.63
in
say, s =
3
in
Minimum edge distance :
Le =
Ag req.
U=
0.85
Ae req.
An req.
3.51
SHEET 102 of 131
(from AISC table J3.4)
1.5
in
2.345679 in2
(from commentary to the AISC specification)
1.7471264 in2
2.0554429 in2
minimum radius of gyration:
r min =
1.532 in
TRY
2L5x3x1/2LLBB
bolts placed in the long leg at the usual gage distance (check LRFD page 10-10)
usual gage =
3
in
Ag =
7.51
in2
>
2.35
in2
OK!
r=
1.58
in
>
1.53
in
OK!
t=
0.5
in
An =
7.01
in2
>
2.0554429 in2
OK!
x = 0.736 in
U = 0.9182222
<
0.9
use U =
0.9
Ae = 6.309 in2
>
1.7471264 in2
OK!
Check Bearing strength:
for bearing strength computation use a hole diameter of h =
Rn = (1.2 Lc t Fu)
if Lc < 2 d
Rn = (2.4 d t Fu)
if Lc > 2 d
Page 5
15/16
in
Sheet3
For the hole nearest the edge of the member :
Lc =
1.03
in
Rn =
2d=
1.75
in
For the other holes:
Lc =
2.06
in
Rn =
2d=
1.75
in
Total bearing strength of the connection :
Rn =
163.94 kips >
76 kips
26.92
kips/bolt
45.68
kips/bolt
OK!
Red font indicates user input
PROJECT: STEEL BUILDING DESIGN CASE STUDY
SUBJECT: Bolted connection
SHEET 103 of 131
Check Block shear:
Shear areas:
Agv =
5.25
Anv =
3.50
in2
in2
Tension areas:
Agt =
0.50
Ant =
0.25
in2
in2
Shear rupture design strength Vn:
(.6*Fu)*Anv =
LRFD J4-1
91.35 kips
Tension rupture design strength Tn:
Fu*Ant =
LRFD J4-2
10.875 kips
The larger fracture term controls:
LRFD J4-1 controls
Block shear strength:
Rn =
Rn =
104.85
102.225
kips <
kips >
102.225
Pu/2 =
38
kips
OK!
Le =
Le =
1.5
in
s=
Page 6
in.
1.5
in
Sheet3
g=
in
Use a
Use
2L5x3x1/2LLBB
4
7/8
with the long leg connected.
in. A325 bolts.
Red font indicates user input
Page 7
Sheet3
EET 101 of 131
(kips)
(ksi)
(ksi)
(ksi)
(ft)
table J3.1 LRFD
Page 8
Sheet3
ET 102 of 131
otted holes, shall
0-10)
Page 9
Sheet3
ET 103 of 131
Page 10
Sheet3
Page 11
Sheet16
Page 12
Sheet16
RENZXYMON
Page 13
Sheet16
RENZXYMON
Page 14
