Scribd
Upload
45 views5 pages

Electrical Rating

The document provides setup instructions for a water level controller, including how to configure parameters like reserve level, tank height, and time slots for water delivery, and how to connect the controller to a water tank sensor and power supply. Step-by-step instructions are given for initial setup and configuration of the controller parameters and time/date. Diagrams show how the water level sensor and overflow pipe should be installed in the water tank.

Uploaded by

Murad Lansa Abdul Khader
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
45 views5 pages

Electrical Rating

The document provides setup instructions for a water level controller, including how to configure parameters like reserve level, tank height, and time slots for water delivery, and how to connect the controller to a water tank sensor and power supply. Step-by-step instructions are given for initial setup and configuration of the controller parameters and time/date. Diagrams show how the water level sensor and overflow pipe should be installed in the water tank.

Uploaded by

Murad Lansa Abdul Khader
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Electrical Rating

Input Supply

- 100-265VAC

Power Consumption
Relay Rating

- <4 W
- 30A(Resistive) at 230VAC (Upto 1.5HP
Single Phase)

Maximum Cable Length(Sensor) - 60Meter (4 Core Multi stranded


Cable )

Parameter Setup
1.Press and Hold Enter/Fill Button at Boot Time
2.Press Enter/Fill Button for Parameter Navigation
3.Chaging the Parameter by Pressing Select/Change Button
4.Press Enter/Fill Button for Digit Navigation
5. Press Select/Change Button Increment value
6.For Next Window Navigate Cursor to >> and Press Select/Change Button
7. For Saving Navigate Cursor to >> and Press Select/Change Button
8.Press Select/Change Button again Press Select/Change Button

Time and Date Setup


1.Press and Hold Select/Change Button at Boot Time
2.Select Each Parameter by Pressing Enter/Fill Button
3.Change Value By Pressing Select/Change Button

Symbols
R: - Reserve Level in Percentage
E: - Tank Height from Sensor in CM
ETFP:- Time Out Cutoff Enable or Disable
F:- Time Out Lockout Counter
Time Slots :- Check the water level on that time(For Corporation water consumers)
T: - Total Time to to Fill the Tank
Eg: Tank Height = 130cm,Reserve Level=67%,Corporation water Timing Morning 7 O
clock and evening 6:30
1. Press and Hold Enter/Fill Button at Boot Time
2.Press Enter/Fill Button and Navigate to R: Position on the window
3.Press Select/Change Button
4.Press Select/Change Button to Increment the Digit to 6
5.Press Enter/Fill Button to Select Next Digit
6.Press Select/Change Button to Increment the Digit to 7
7.Press Enter/Fill Button and Navigate to E:
8. Press Select/Change Button
9. Press Select/Change Button to Increment the Digit to 1
10. Press Enter/Fill Button to Select Next Digit
11. Press Select/Change Button to Increment the Digit to 3
12. Press Enter/Fill Button to Select Next Digit
13. Press Select/Change Button to Increment the Digit to 0
14. Press Enter/Fill Button and Navigate to ETFP:
15.Press Select/Change Button to Enable or Disable Select D to Disable
16. Press Enter/Fill Button and Navigate to >> for getting Next window

17. Press Select/Change Button for Time Slot Setup


18. Press Select/Change Button to Increment the Digit to 0
19. Press Enter/Fill Button to Select Next Digit
20. Press Select/Change Button to Increment the Digit to 7
21. Press Enter/Fill Button to Select Next Digit
22. Press Select/Change Button to Increment the Digit to 0
23. Press Enter/Fill Button to Select Next Digit
24. Press Select/Change Button to Increment the Digit to 0
25. Press Enter/Fill Button to Select AMPM
26. Press Select/Change Button to Select AM
27. 25. Press Enter/Fill Button to Time slot 2
28. Press Select/Change Button to Increment the Digit to 0
29. Press Enter/Fill Button to Select Next Digit
30. Press Select/Change Button to Increment the Digit to 6
31. Press Enter/Fill Button to Select Next Digit
32. Press Select/Change Button to Increment the Digit to 3
33. Press Enter/Fill Button to Select Next Digit
34. Press Select/Change Button to Increment the Digit to 0
35. Press Enter/Fill Button to Select AM/PM
36. Press Select/Change Button to Select PM
37. Press Enter/Fill Button and Navigate to >>
38. Press Select/Change Button
39. Press Enter/Fill Button
40.Press Enter/Fill Button to Save

Sensor

Overflow
Pipe

30CM
Water

Water:100%

Tank Height

Water:0%

Electrical Connection
Power Supply

Dolphino Aqua

Sensor Connection
1.Extended the Wire along with the Sensor and Connect to the controller

Red

Yellow

Phase

Black

Neutral

You might also like