Designation: A 494/A 494M 01ae1

An American National Standard

Standard Specification for

Castings, Nickel and Nickel Alloy1

This standard is issued under the fixed designation A 494/A 494M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.

e1 NOTEThe UNS number for the element CU5MCuC in Tables 13 was revised editorially in October 2001.

and Nickel-Chromium-Iron Alloys7

E 76 Test Methods for Chemical Analysis of Nickel-Copper
Alloys6
E 354 Test Methods for Chemical Analysis of HighTemperature, Electrical, Magnetic, and Other Similar Iron,
Nickel, and Cobalt Alloys6

1. Scope *
1.1 This specification covers nickel, nickel-copper, nickelcopper-silicon, nickel-molybdenum, nickel-chromium, and
nickel-molybdenum-chromium alloy castings for corrosionresistant service.
1.2 The values stated in either inch-pound units or SI units
are to be regarded separately as standard. Within the text, the
SI units are shown in brackets. The values stated in each
system are not exact equivalents; therefore, each system must
be used independently of the other. Combining values from the
two systems may result in nonconformance with the specification. Inch-pound units are applicable for material ordered to
Specification A 494 and SI units for material ordered to
Specification A 494M.

3. Terminology
3.1 Definitions:
3.1.1 master heata single furnace charge of refined alloy
which may either be poured directly into castings or into remelt
alloy for individual melts.
3.1.2 meltsa single furnace charge poured into castings.
When master heats are used to prepare melts, a melt analysis
shall be reported.

2. Referenced Documents
2.1 ASTM Standards:
A 370 Test Methods and Definitions for Mechanical Testing
of Steel Products2
A 488/A488M Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel3
A 732/A732M Specification for Castings, Investment, Carbon and LowAlloy Steel for General Application, and
Cobalt Alloy for High Strength at Elevated Temperatures3
A 781/A781M Specification for Castings, Steel and Alloy,
Common Requirements, for General Industrial Use3
E 8 Test Methods for Tension Testing of Metallic Materials4
E 29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications5
E 30 Test Methods for Chemical Analysis of Steel, Cast
Iron, Open-Hearth Iron, and Wrought Iron6
E 38 Methods for Chemical Analysis of Nickel-Chromium

4. General Conditions for Delivery

4.1 Material furnished to this specification shall conform to
the requirements of Specification A 781/A 781M, including
any supplementary requirements that are indicated in the
purchase order. Failure to comply with the general requirements of Specification A 781/A 781M constitutes nonconformance with this specification. In case of conflict between the
requirements of this specification and Specification A 781/
A 781M, this specification shall prevail.
5. Ordering Information
5.1 Orders for castings to this specification should include
the following information:
5.1.1 Quantity, in pieces, and
5.1.2 Grade designation (Table 1) and class (Table 2).
5.2 The purchaser shall specify any of the following information required to describe adequately the desired material:
5.2.1 Heat treat condition (see 6.1 and 6.2),
5.2.2 Repair welding (see 11)
5.2.3 Source inspection requirements, if any (see Specification A 781/A 781M),
5.2.4 Marking-for-identification requirements, if any (see
13.1), and
5.2.5 Supplementary requirements desired, including the

1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee
A01.18 on Castings.
Current edition approved Sept. 10, 2001. Published November 2001. Originally
published as B 332 58 T. Redesignated as A 494 in 1963. Last previous edition
A 494/A 494M 01.
2
Annual Book of ASTM Standards, Vol 01.03.
3
Annual Book of ASTM Standards, Vol 01.02.
4
Annual Book of ASTM Standards, Vol 03.01.
5
Annual Book of ASTM Standards, Vol 14.02.
6
Annual Book of ASTM Standards, Vol 03.05.

Discontinued, see 1989 Annual Book of ASTM Standards, Vol 03.05.

*A Summary of Changes section appears at the end of this standard.

Copyright ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.

TABLE 1 Chemical Requirements

NOTE 1Values are maximum unless otherwise indicated.

Composition, %
Element

CZ-100

M-35-1A

M-35-2

M-30H

M-25S

M-30CA

N-12MV

N-7M

CY-40

CW12MW

CW-6M

CW-2M

CW-6MC

CY5SnBiM

CX2MW
(N26022)

CU5MCuC
(N08826)

C, max

1.00

0.35

0.35

0.30

0.25

0.30

0.12

0.07

0.40

0.12

0.07

0.02

0.06

0.05

0.02

Mn, max
Si, max
P, max

1.50
2.00
0.03

1.50
1.25
0.03

1.50
2.00
0.03

1.50
2.7-3.7
0.03

1.50
3.5-4.5
0.03

1.50
1.0-2.0
0.03

1.00
1.00
0.040

1.00
1.00
0.040

1.50
3.00
0.03

1.00
1.00
0.040

1.00
1.00
0.040

1.00
0.80
0.03

1.00
1.00
0.015

1.5
0.5
0.03

1.00
0.80
0.025

S, max

0.03

0.03

0.03

0.03

0.03

0.03

0.030

0.030

0.03

0.030

0.030

0.03

0.015

0.03

0.025

Cu

1.25
max
...

26.033.0
...

26.033.0
...

27.033.0
...

27.033.0
...

26.033.0
...

...

...

...

...

...

...

...

...

...

3.50
max
balance

3.50
max
balance

5.0 max

2.0 max

2.0-6.0

balance

15.0
-17.5
2.0
max
balance

12.5-14.5

3.50
max
balance

17.020.0
3.0 max

2.0-3.5

3.50
max
balance

16.018.0
4.5-7.5

8.0-10.0

3.50
max
balance

30.033.0
3.00
max
balance

...

balance

balance

balance

Cr

3.00
max
95.00
min
...

26.030.0
4.0-6.0

...

...

...

...

...

1.00

1.0

...

...

1.0-3.0

...

...

3.15-4.50

...

...

...

0.5
max
...

15.017.5
...

20.0-22.5

0.5
max
...

17.020.0
...

11.0-14.0

...

15.517.5
...

20.0-23.0

Cb (Nb)

14.017.0
...

...

...

...

...

...

...

...

...

2.5-3.5

...

...

...

...

...

...

...

...

...

...

...

0.35 max

...

Bi
Sn

...
...

...
...

...
...

...
...

...
...

...
...

0.200.60
...
...

1.0
max
...

...

...
...

...
...

3.755.25
0.200.40
...
...

38.044.0
19.523.5
0.601.20
...

...
...

...
...

...
...

3.0-5.0
3.0-5.0

...
...

...
...

Mo
Fe
Ni

Order M-351 or M-30C when weldability is required.

balance

balance

A 494/A 494M

balance

11.0
max
balance

0.050
max
1.0 max
1.0 max
0.030
max
0.030
max
1.503.50
2.5-3.5

A 494/A 494M
TABLE 2 Heat Treat Requirements
Grade

Heat Treatment

CZ-100, M-35-1, M-35-2, CY-40 Class 1, M-30H, M-30C,

M-25S Class 1, CY5SnBiM
M-25S, Class 2A

As cast
Load into furnace at 600F [315C] maximum. Heat to 1600F [870C] and hold
for 1 h plus an additional 30 min for each 12 in. [13 mm] of cross section over 1
in.B Cool to 1300F [705C]C and hold at temperature for 30 min then quench in
oil to room temperature.
Load into furnace at 600F [315C] maximum. Heat slowly to 1100F [605C] and
hold to develop maximum hardness. Furnace or air cool to room temperature.
Heat to 2000F [1095C] minimum, hold for sufficient time to heat castings to
temperature, quench in water or rapid cool by other means.
Heat to 2150F [1175C] minimum, hold for sufficient time to heat castings to
temperature, quench in water or rapid cool by other means.
Heat to 1900F [1040C] minimum, hold for sufficient time to heat castings to
temperature, quench in water or rapid cool by other means.
Heat to 2200F [1205C] minimum, hold for sufficient time to heat castings to
temperature, quench in water or rapid air cool by other means.
Heat to 2100F [1150C] minimum, hold for sufficient time to heat castings to
temperature, quench in water. Stabilize at 17251815F [940990C], hold for
sufficient time to heat castings to temperature, quench in water or rapid cool by
other means.

M-25S, Class 3
N-12MV, N-7M
CW-12MW, CW-6M, CW-6MC, CW-2M
CY-40, Class 2
CX2MW (N26022)
CU5MCuC (N08826)

A
M-25S, while machinable in the as cast condition, is capable of being solution treated for improved machinability. It may be subsequently age hardened to the
hardness specified in Table 3 and finished machined or ground.
B
For cross sections over 6 in. [125 mm] it may be necessary to increase the hold time if maximum softness is desired.
C
For maximum softness and the least variation in hardness levels, castings should be transferred from an oven at 1600F [870C] to a second oven at 1300F [705C].

representative sample taken during the pouring of the master

heat. Chemical composition shall be reported to the purchaser
or his representative.
7.3 Test Methods E 76 or Test Methods E 354 shall be used
for referee purposes. Test Methods E 30 or Methods E 38 shall
be used if Test Methods E 76 or Test Methods E 354 do not
include a method for some element present in the material.

standards of acceptance.
6. Heat Treatment
6.1 Castings shall be heat treated in accordance with the
requirements in Table 2.
NOTE 1Proper heat treatment of these alloys is usually necessary to
enhance corrosion resistance and, in some cases, to meet mechanical
properties. Minimum heat treat temperatures are specified; however, it is
sometimes necessary to heat treat at higher temperatures, hold for some
minimum time at temperature, and then rapidly cool the castings in order
to enhance the corrosion resistance and meet mechanical properties.

8. Tensile Properties
8.1 One tension test shall be made from each master heat
except for grades M-25S and CY5SnBiM when the master heat
is used to pour the castings. One tension test shall be made
from each melt except for grades M-25S and CY5SnBiM. Test
results shall conform to the tensile requirements specified in
Table 3. Test bars shall be poured in special blocks from the
same heat as the castings represented.
8.2 The bar from which the test specimen is taken shall be
heat treated in production furnaces to the same procedure as the
castings it represents. If the castings are not heat treated, the
bar used for the test specimen must not be heat treated.
8.3 Test specimens may be cut from castings, at the producers option, instead of from test bars.
8.4 When castings are produced by methods other than

6.2 When Class 1 is specified, grades CY40 and M-25S

shall be supplied in the as-cast condition. When Class 2 is
specified, grades CY40 and M-25S shall be supplied in the
solution-treated condition. When Class 3 is specified, grade
M-25S shall be supplied in the age-hardened condition.
7. Chemical Composition
7.1 These alloys shall conform to the chemical composition
requirements prescribed in Table 1.
7.2 An analysis of each master heat shall be made by the
manufacturer to determine the percentages of the elements
specified in Table 1. The analysis shall be made from a

TABLE 3 Mechanical Properties

CZ100
Tensile strength,
min, psi [MPa]
Yield strength,
min, psi [MPa]
Elongation in 2 in.
[50 mm],A min, %
Hardness HB

M-35-1 M-35-2 M-30H M-25S M-30C

50 000 65 000 65 000 100 00

[345] [450] [450] [690]
18 000 25 000 30 000 60 000
[125] [170] [205] [415]
10.0
25.0
25.0
10.0
...

...

...

...

...
...
...
B

N-12MV N-7M

65 000 76 000
[450]
[525]
32 500 40 000
[225]
[275]
25.0
6.0
...

CY-40 CWCW-6M CW-2M CW12MW

6MC

76 000 70 000 72 000 72 000 72 000 70 000

[525] [485] [495] [495] [495]
[485]
40 000 28 000 40 000 40 000 40 000 40 000
[275] [195] [275] [275] [275]
[275]
20.0
30.0
4.0
25.0
20.0
25.0

...

...

...

...

...

...

...

CY5SnBiM CX2MW CU5MCuC

(N26022)
(N08826)
...
...
...
...

80 000
[550]
45 000
[310]
30.0
...

75 000
[520]
35 000
[240]
20.0
...

When ICI test bars are used in tensile testing as provided for in Specification A 732/A 732M, the gage length to reduced section diameter ratio shall be 4 to 1.
B
300 HB minimum for the age hardened condition.

A 494/A 494M
11.3 Castings of M-30H, M-25S, and CY5SnBiM may not
be weld repaired.
11.4 Grades N-12MV, N-7M, CW-12MW, CW-6M, CW2M, and CX2MW may require post weld heat treatment after
major weld repairs. If post weld heat treatment is required, it
must be specified along with the grade. If required, it shall be
performed in accordance with Section 6.
11.5 For grade CU5MCuC, the composition of the deposited weld metal shall be similar to that of AWS A5.14 ER
NiCrMo-3 (UNS N06625) or AWS A5.11 E NiCrMo-3
(UNS W86112).

investment process, tension test coupons shall be machined to

the form and dimension shown in Fig. 8 of, and tested in
accordance with, Test Methods E 8.
8.4.1 When castings are produced by the investment process, test specimens in accordance with Specification A 732/
A 732M shall be used for measurement of tensile properties.
8.5 If any specimen shows defective machining or develops
flaws, it may be discarded and another substituted from the
same heats.
8.6 To determine conformance with the tension test requirements, an observed value or calculated value shall be rounded
in accordance with Practice E 29 to the nearest 500 psi [3.5
MPa] for yield and tensile strength and to the nearest 1 % for
elongation and reduction of area.

12. Rejection and Rehearing

12.1 Samples that represent rejected material shall be preserved for two weeks from the date of transmission of the
rejection report. In case of dissatisfaction with the results of the
tests, the manufacturer may make claim for a rehearing within
that time.

9. Workmanship, Finish, and Appearance

9.1 Critical surfaces of all castings intended for corrosionresistant service shall be cleaned. Cleaning may be accomplished by blasting with clean sand or metallic corrosionresistant shot or by other approved methods.

13. Product Marking

10. Quality
10.1 The castings shall not be peened, plugged or impregnated to stop leaks.
10.2 Internal chills and chaplets may be used in the manufacture of castings. However, the chills, chaplets and affected
cast material must be completely removed.

13.1 Castings shall be marked for the material identification

with the ASTM specification designation (A 494/A 494M) and
grade symbol, that is, CY-40. The manufacturers name or
identification mark and the pattern number shall be cast or
stamped on all castings except those of such small size as to
make such marking impractical. To minimize small defects
caused by dislodged particles of molding sand, the number of
cast identification marks shall be minimized. The marking of
heat numbers on individual castings shall be agreed upon by
the manufacturer and the purchaser. Markings shall be in such
position as not to injure the usefulness of the casting.
13.1.1 When the castings are too small to mark individually,
a symbol traceable to the heat shall be placed on the castings
and the required identification then placed on a tag affixed to
the container in which these castings are shipped.

11. Repair by Welding

11.1 Repairs shall be made by using a welding procedure
and operators capable of producing sound welds. The composition of deposited weld metal shall be similar to that of the
castings.
11.2 Weld repairs shall be considered major in the case of a
casting that has leaked on hydrostatic test or when the depth of
the cavity after preparation for repair exceeds 20 % of the
actual wall thickness, or 1 in. [25 mm], whichever is smaller,
or when the extent of the cavity exceeds approximately 10 in.2
[65 cm2]. All other weld repairs shall be considered minor.
Major and minor weld repairs shall be subject to the same
quality standards as are used to inspect the castings.

14. Keywords
14.1 corrosion resistant applications; nickel; nickel alloy
castings; nickel alloys; nickel castings

SUPPLEMENTARY REQUIREMENTS
The following supplementary requirements shall not apply unless specified in the purchase order. A
list of standard supplementary requirements for use at the option of the purchaser is included in
Specification A 781/A 781M. Those which are ordinarily considered for use with this specification are
given below; others enumerated in Specification A 781/A 781M may be used with this specification
upon agreement between the manufacturer and the purchaser.
condition, hardness tests shall be made in accordance with Test
Methods and Definitions A 370. The test location, number of
tests, and hardness values shall be agreed upon between the
manufacturer and purchaser.
S10.1.1 If castings are ordered in the as-cast condition,
hardness determinations shall be made on two different representative areas of each casting or coupon selected for test.

S2. Radiographic Examination

S3. Liquid Penetrant Examination
S6. Certification
S10. Hardness Tests
S10.1 When composition M-25S material is ordered with a
hardness maximum or range in the as-cast or solution treated
4

A 494/A 494M
S22.1.1.4 The clamps may be removed from the specimen
after the first two weld passes have been completed.
S22.1.1.5 Deposit alternate series of passes until the double
V-groove has been completely filled. After the second series
(number 4 pass) a 532-in. [4-mm] diameter electrode may be
used if desired.
S22.1.1.6 During welding allow each pass to cool, clean,
and examine visually for cracks. The presence of cracks shall
be cause for rejection.
S22.1.1.7 Upon completion of the welding, cut one section
approximately 34 in. [19 mm] long transverse to the weld from
each end and discard.
S22.1.1.8 Polish each end of the remaining center section on
a 100/200-grit wheel and etch with concentrated HNO3 or with
Lepitos etchant. Prepare Lepitos etchant as follows: (a) 15 g
of (NH4) 2SO4 dissolved in 75 cm3 of water; (b) 250 g of
FeCl3(powdered) dissolved in 100 cm3 of HCl; (c) mix
solutions (a) and (b) and add 30 cm3of HNO3.
S22.1.1.9 Examine the etched section under low magnification (5 to 103). The lot represented by the test specimen shall
be accepted if it complies with the following crack requirements: (a) Three cracks maximum in linear inch of base metal
and (b) The length of any crack in the base metal does not
exceed 0.20 in. [5 mm].
S22.1.1.10 Cracks observed in the weld metal during the
low-magnification examination shall not be cause for rejection.
S22.1.1.11 Failure of welded test bars to comply with any of
the requirements S22.1 through S22.1.1.10 shall result in
rejection of the lot represented.
S22.1.2 Prepare and weld the test bar cast in accordance
with Fig. 2 as follows:
S22.1.2.1 Fill the groove in the block completely with weld
deposit using manual metallic arc process with 18-in. [3.2mm]
or 532-in. [4-mm] diameter electrodes that will deposit metal of
similar composition of the test piece.
S22.1.2.2 Remove one 38-in. [10-mm] thick bend coupon
longitudinally from the welded block by machining, sawing,
abrasive cutting, or other suitable means. Make a transverse
side bend test of the welded joint in accordance with Practice
A 488/A 488M.
S22.1.2.3 Remove a transverse weld macro-specimen from
the welded plate and visually examine for cracks. This specimen may be the same one to be used for the bend specimen.
S22.1.3 Acceptance:
S22.1.3.1 Cracks as tears in the casting in the fusion zone or
heat-affected zone of the macro-specimen shall be cause for
rejection. Cracks originating at the weld bead undercuts, at
weld slag inclusions, or at casting defects shall not be cause for
rejection.
S22.1.3.2 Cracks or other open defects exceeding 18-in. [3.2
mm] measured in any direction on the convex surface of the
bent specimens shall be cause for rejection, except that cracks
occurring on the corners while testing and cracks originating at
weld bead undercuts shall not be considered.

S10.1.1.1 By agreement between purchaser and producer,

those as-cast castings which fail to meet the required hardness
may be accepted in the solution annealed and hardened
condition if the hardness thus developed meets the hardness
requirement of the specification.
S10.1.2 If castings ordered are in the solution-treated condition, two sample castings or two coupons representing the lot
shall be heat treated for tests (see S10.1.1). Hardness determinations shall be made on two different representative areas of
each casting or coupon.
S10.1.3 When hardness tests are made, the specimens shall
be at least 14 in. [6 mm] in thickness and the area to be tested
shall be ground clean before the hardness tests are made.
S22. Weldability Test
S22.1 If weldability tests are specified for M-30-C or
M-35-1, prepare a coupon obtained from a test bar shown in
Fig. 1 or Fig. 2 for each lot of composition M-30-C or M-35-1
castings. The weld test to be used shall be agreed upon between
the purchaser and manufacturer.
S22.1.1 Prepare and weld the test bar cast in accordance
with Fig. 1 and in accordance with Fig. 3.
S22.1.1.1 Machine the cast skin and unsound metal from
two adjacent faces of the as-cast specimen, exclude the riser
face, and cut the specimen into approximately 6-in. [150-mm]
lengths.
S22.1.1.2 Clamp the two 6-in. [150 mm] lengths together to
form a double V-joint and weld two passes at a time on
alternate sides of the specimen using 18-in. [3-mm] diameter
electrodes that will deposit metal of similar composition of the
test pieces.
S22.1.1.3 Allow the specimen to cool to room temperature
between passes, remove all flux, and examine visually for
cracks.

Metric Equivalents
in.

12

[mm]

[25]

[75]

[100]

[305]

NOTE 1Riser shall be machined off and 1 in. [25 mm] square by 12
in. [305 mm] coupon shall be used for x-weld test. See Fig. 3.
FIG. 1 Weld Test Bar (As Cast)

A 494/A 494M

Metric Equivalents
in.

14

38

34

118

234

314

[mm]

[5]

[10]

[20]

[30]

[70]

[85]

[155]

FIG. 2 Weld Test Bar (As Cast)

Metric Equivalents
in.

[mm]

34

412

[20]

[115]

FIG. 3 X-Weld Test

SUMMARY OF CHANGES
This section identifies the the principle changes to this specification that have been made since the last issue.
(1) Metric value for yield strength of CX2MW in Table
3Revised.

A 494/A 494M
The ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item
mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights,
and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website (www.astm.org).