SOP Reach Stacker01

SOP REACH STACKER
STANDRAD OPERATING PROCEUDRE FOR

MAINTENANCE OF
REACH STACKER
SOP REACH STACKER
INDEX
1.0
DAILY CHECK UP
2.0
MAINTENANCE PROCEDURES
2.1
Drive chain adjustment
1 DAILY CHECK UP
1) Check oil level before starting
2) Check the hydraulic oil level
3) Check the coolant level in the radiator
4) Check the coolant level in the coolant reservoir
5) Lubricate the designated locations
6) Drain the water separator
7) check the operation of all switches
8) Check operation of all controls
9) Check level of window washer liquid
MAINTENANCE PROCEDURES
SOP REACH STACKER
2.1
Removal of AC compressor clutch -
Responsibility: In-Charge, Shift Engineer, Work Leader

Purpose:
Description of procedure for removal of AC compressor clutch
Scope:
To be done at recommended interval.
Operating Procedures
TOOLS AND MATERIAL REQUIRED: Tool box,

Armature nut removal
1) Remove bolts holding dust cover in place and remove cover. If auxiliary sheet metal pulley is
present, remove the screws holding is it place. Then remove pulley.
2) Insert pins of armature plate spanner into threaded holes of armature assembly.
3) Hold armature assembly stationary while removing retaining nut with wrench.
Key shaft armature removal
Remove armature plate assembly using puller. Thread 3 puller bolts into the threaded holes in
the bolts into the threaded holes in the armature assembly. Turn center screw clockwise until
armature assembly comes loose.
Spline shaft armature removal:
1) The spline shaft armature will not have threaded holes to accept the armature puller.
2) Lift off armature plate with fingers. If armature does not come off easily, spray an anti-seize oil
into shaft to loosen. Armature plate can also be loosened by gently prying between rotor and
armature plate with two flat screwdrivers.
Remove clutch accessories:
Remove bearing dust cover, shaft key and shims
Rotor pulley assembly removal:
1) Remove rotor snap ring.
2) Insert the lip of the jaws into the snap ring groove.
3) Place rotor pulley shaft protector over the exposed shaft.
4) Align thumb screws to puller jaws and finger tighten.
5) Turn puller center bolt clockwise using a socket wrench until rotor pulley is free.
Field coil assembly removal:
1) Loosen lead wire clamp screw with Philips screw driver until wires can be slipped out from
under clamp.
2) Undo any wire connection on the compressor which would prevent removal of the field coil
assembly.
3) Remove field coil snap ring.
SOP REACH STACKER
4) Remove the field coil assembly.
2.2
Replacement of clutch -

Purpose:
Description of procedure for replacement of clutch
Scope:

Field coil assembly installation
Reverse the steps of FILED COIL ASSEMBLY REMOVAL. Protrusion on underside of coil ring must
match hole in front housing to prevent movement and correctly locate lead wires.
Rotor assembly installation
1) Place compressor on support stand, supported at rear end of compressor. If the compressor
must be clamped in a vise, clamp only on the mounting ears, never on the body of the
compressor.
2) Set rotor squarely over the front housing boss.
3) Place the rotor installer ring into the bearing bore. Ensure that the edge rests only on the inner
race of the bearing, not on the seal, pulley or outer race of the bearing.
4) Place the driver into the ring and drive the rotor down onto the front housing with a hammer or
arbor press. Drive the rotor against the front housing step. A distinct change of sound can be
heard when using the hammer to install the rotor.
5) Reinstall rotor retaining snap ring with external snap ring pliers. If a bevel is present on the snap
sing, it should face up (away from the body of the compressor).
6) Reinstall rotor bearing dust cover by gently tapping it into place.
Armature assembly installation
1) Install clutch shims. NOTE: clutch air gap is determined by shim thickness. When installing a
clutch on a used compressor, try the original shims first. When installing a clutch on a
compressor that has not had a clutch install before, first try 0.04, 0.02 and 0.004 shims.
2) Install shaft key with pliers.
3) Align keyway in armature assembly to shaft key. Using driver and a hammer or arbor press,
drive the armature assembly down over the shaft until it bottoms on the shims. A distinct sound
change will be noted if driving with a hammer.
4) Align slit in armature with locator tooth on shaft. Press armature towards rotor with hand until
armature rests against the shims.
SOP REACH STACKER
2.3
Replacement of cylinder head -

Purpose:
Description of procedure for replacement of cylinder head
Scope:

Cylinder head removal
1) Be sure all internal compressor pressure has been relieved.
2) Inspect cylinder head for fitting or thread damage.
3) Remove cylinder head bolts.
4) Use a small hammer and gasket scraper to separate the cylinder head from the valve plate. Be
careful not to scratch the gasket surface of the cylinder head.
5) Carefully lift the cylinder head from the valve plate.
6) It is recommended that both the head gasket (between the cylinder head and the valve plate)
and the block gasket (between the valve plate and the cylinder block) be replaced any time the
cylinder head is removed. However, if no service is required to the valve plate, it may be left in
place. If the valve plate comes loose from the cylinder block, the block gasket must be replaced.
7) Carefully remove old head gasket from top of valve plate with gasket scraper. Be careful not to
disturb the valve plate to cylinder block joint if valve plate has been left in place. If valve plate
comes loose from cylinder block, proceed to valve plate removed, and replace block gasket.
Cylinder head removal
1) Using a small hammer and gasket scraper, carefully separate valve plate from cylinder block.
Be careful not to damage sealing surface of cylinder block.
2) Inspect reed valves and retainer. Replace valve plate assembly if any part is damaged.
3) Carefully remove any gasket material remaining on valve plate, cylinder block or cylinder head.
Do not damage sealing surface on components.
Valve plate and cylinder head installation
1) Coat new block gasket with clean 5GS refrigerant oil.
2) Install block gasket. Align new gasket to location pin holes and orifices. Notch should face same
direction as oil plug or adaptor.
3) Place valve plate on cylinder block with discharge valve, retainer and nit facing up and location
pins properly located in holes.
4) Use vacuum pump and small tube to remove residual oil from each bolt hole. If this step is not
performed, hydraulic pressure can be created when the cylinder head bolts are tightened. This
pressure can beak the cylinder block.
5) Coat head gasket with clean 5GS refrigerant oil.
6) Install head gasket cover location pins, checking for correct orientation.
7) Install cylinder head.
8) Install cylinder head bolts and tighten in a star pattern.
SOP REACH STACKER
2.
Assembly of drive pinion bearing -

Purpose:
Description of procedure for assembly dive pinion bearing.
Scope:

1) Insert the two outer rings of the taper roller bearings into the differential carrier.
2) Calculate the thickness of space ring.
3) Heat the drive pinion side taper roller bearing to about 100
SOP REACH STACKER

SOP Reach Stacker01

Uploaded by

Copyright:

Available Formats

SOP Reach Stacker01

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SOP Reach Stacker01

Uploaded by

Copyright:

Available Formats

SOP REACH STACKER

STANDRAD OPERATING PROCEUDRE FOR