TC - Rcue 40 - 240 WG2 (TCGB0045 (12-06)

Technical Catalog
Installation, Operation and Maintenance Instructions.

Design Information
WATER COOLED
WATER CHILLERS
-SCREW TYPERCUE40WG2-240WG2 (R407C)
Capacity 134 kW-696 kW
Heat Pump Option
Heating Capacity 161 kW-824 kW
TABLE OF CONTENTS
1. IMPORTANT NOTICE................................................................................................................. 1
2. FEATURES AND BENEFITS...................................................................................................... 1
2.1. NEW CHILLER PICTURE.....................................................................................................................1
2.2. COMPRESSOR ....................................................................................................................................2
2.3. CONTROL ............................................................................................................................................3
2.4. HEAT EXCHANGER.............................................................................................................................4
2.5. NEW ELECTRONIC EXPANSION VALVE ...........................................................................................4
3. OPERATION INSTRUCTIONS ................................................................................................... 4

3.1. HITACHI WATER COOLED WATER CHILLER MODELS: RCUE 40-240 WG2 ..................................4
4. COMPONENTS OF CHILLER .................................................................................................... 5

4.1. STRUCTURE DRAWING .....................................................................................................................5
5. PREPARATION INITIAL CHECK ............................................................................................... 6

5.1. INITIAL CHECK ....................................................................................................................................6
5.2. PLACING THE UNIT.............................................................................................................................6
5.3. CENTRE OF GRAVITY ........................................................................................................................7
5.4. SERVICE SPACE AND FOUNDATION................................................................................................8
5.5. TRANSPORTATION BY RIGGING.......................................................................................................9
6. INSTALLATION .......................................................................................................................... 10
6.1. ELECTRICAL WIRING .........................................................................................................................10
6.2. WATER PIPING....................................................................................................................................12
6.3. MINIMUM INTERNAL SYSTEM WATER VOLUME .............................................................................13
6.4. WATER CONTROL ..............................................................................................................................13
6.5. BMS CONNECTION .............................................................................................................................15
6.6. CSC-5S.................................................................................................................................................21
6.7. INSTALLATION FINAL CHECK............................................................................................................24
7. TEST RUNNING.......................................................................................................................... 25
7.1. PREPARATION ....................................................................................................................................25
7.2. TEST RUNNING ...................................................................................................................................25
7.3. INSTRUCTIONS AFTER TEST RUNNING ..........................................................................................26
8. CONTROLLER ADJUSTMENT .................................................................................................. 26

8.1. CONTROL SYSTEM.............................................................................................................................27
8.2. CONTROLLER ADJUSTMENT ............................................................................................................28
9. SELF-INSPECTION FUNCTIONS .............................................................................................. 30

9.1. ALARM INDICATION............................................................................................................................30
9.2. NORMAL INDICATION.........................................................................................................................31
9.3. FUNCTION FOR INDICATION OF OPERATION CONDITION ............................................................31
10. CONTROL SYSTEM ................................................................................................................. 36

11. MAINTENANCE ........................................................................................................................ 39
11.1. COMPONENTS ..................................................................................................................................39
11.2. LUBRICATION....................................................................................................................................39
11.3. DEPOSITS..........................................................................................................................................39
11.4. CLEANING METHOD .........................................................................................................................40
11.5. WINTER SHUTDOWN........................................................................................................................41
11.6. SPRING START-UP ...........................................................................................................................41
11.7. PART REPLACEMENT ......................................................................................................................41
11.8. REFRIGERATION CYCLE..................................................................................................................42
11.9. REFRIGERANT CYCLE DIAGRAM OF HITACHI WATER COOLED CHILLER.................................42
11.10. COMPRESSOR REMOVAL..............................................................................................................44
11.11. SAFETY AND PROTECTION CONTROL ........................................................................................44
11.12. NORMAL OPERATING PRESSURE................................................................................................46
11.13. TEST RUNNING AND MAINTENANCE RECORD ...........................................................................47
11.14. DAILY OPERATING RECORDS.......................................................................................................48
11.15. SERVICING FOR R407C REFRIGERANT SYSTEM .......................................................................48
12. TROUBLESHOOTING .............................................................................................................. 49
13. GENERAL SPECIFICATIONS .................................................................................................. 51

13.1. GENERAL DATA ................................................................................................................................51
13.2. OPTION LINE UP ...............................................................................................................................54
14. DRAWINGS ............................................................................................................................... 55

14.1. DIMENSIONAL DRAWINGS ..............................................................................................................55
14.2. WIRING DIAGRAMS ..........................................................................................................................60
15. MODEL SELECTION ................................................................................................................ 70

15.1. SELECTION EXAMPLE .....................................................................................................................70
15.2. PERFORMANCE TABLE ...................................................................................................................71
15.3. ELECTRICAL DATA ...........................................................................................................................77
15.4. SOUND DATA ....................................................................................................................................78
16. APPLICATION DATA ............................................................................................................... 79

16.1. WORKING RANGE ............................................................................................................................79
16.2. PART LOAD PERFORMANCE ..........................................................................................................79
16.3. ETHYLENE GLYCOL APPLICATION.................................................................................................80
17. COMPONENTS DATA .............................................................................................................. 81

17.1. COMPRESSOR..................................................................................................................................81
17.2. CONDENSER AND WATER COOLER ..............................................................................................81
IMPORTANT NOTICE
1/1
1. IMPORTANT NOTICE
HITACHI pursues a policy of continuing improvement in
design and performance of Products. The right is therefore
reserved to vary specifications without notice.
HITACHI cannot anticipate every possible circumstance
that might involve a potential hazard.
No part of this manual may be reproduced without written
permission.
Signal words (DANGER, WARNING and CAUTION) are
used to identify levels of hazard seriousness. Definitions
for identifying hazard levels are provided below with their
respective signal words.
DANGER:
Immediate hazards which WILL result in severe

personal injury or death.
WARNING:
Hazards or unsafe practices which COULD result

in sever personal injury or death.
CAUTION:
Hazards or unsafe practices which COULD result

in minor personal injury or product or property
damage.
NOTE:
Useful information for operation and/or maintenance.
If you have any questions, contact your contractor or

dealer of HITACHI.
This instruction gives a common description and
information for this water cooled water Chiller which you
operate as well as for other models.
This water cooled water Chiller has been designed for
the following temperatures. Operate the water cooled
water Chiller within this range.
Working Range
Maximum
Condenser Water
Outlet
Temperature
Chilled Water
Outlet
Temperature
C
Minimum
45
*(55)
22
15
5
**(-10)
(*) In case of High Condensing option and Heat Pump

operation option.
(**) In case of low water temperature option.
This instructions should be considered as a permanent
part of the water cooled water Chiller equipment and
should remain with the water cooled water Chiller
equipment.
2. FEATURES AND BENEFITS

2.1. NEW CHILLER PICTURE
HITACHI is a world leader in technology and with

continual research and product development, now offers
a screw type Water Cooled Chiller.
A wide range of capacities are available from 134 kW to

696 kW.
Heating operation is available for option. Heating
Capacities are available from 161 kW to 824 kW.
2/2
FEATURES AND BENEFITS
2.2. COMPRESSOR
THE SAMURAI RANGE
INCORPORATES THE LATEST

DEVELOPMENT OF HITACHIS
SCREW COMPRESSOR
TECHNOLOGY FOR THE NEW
MILLENNIUM.
Highly Reliable HITACHI Two-Pole

Motor
Built-in Oil Separator (Cyclone oil

separator)
Oil Sight Glass

Oil Heater
High precision Twin Screw Rotors
Suction Filter
-LOW VIBRATION-
TWIN SCREW COMPRESSOR
Reciprocating
Screw
AMPLITUDE (m)
By having so few moving parts, it has become highly reliable

with very low noise level and low vibration
Time (second)
PRINCIPLE OF COMPRESSION
Discharge Port
Suction Port
HITACHIs Continuous Capacity Control system uses

advanced electronic controls to position the infinitely
variable slide valve within each compressor.
This modulation allows exact load control and accurate
chilled water temperature without the need for
expensive inverters.
COOLING LOAD %
CONTINUOUS CAPACITY CONTROL
Cooling load = continuos capacity control

Step
control
TIME (Hour)
FEATURES AND BENEFITS
2/3
-PART LOAD PERFORMANCE-
ENERGY SAVING
MOTOR INPUT (%)
Thanks to Continuous Capacity Control, 15~20% energy

saving is possible compared with current step control
systems due to the following:
-The cooling load can be more closely matched
-Continuous Capacity Control takes advantage of high
efficiency part load performance.
-Frequent compressor starts and stops are eliminated.
Continuous
Capacity
Control
COOLING CAPACITY (%)
2.3. CONTROL
MANY FUNCTIONS
Newly developed Control Board has many functions
shown below as standard.
Forced compressor load control
2 Different temperature setting
Memory data in alarm
Automatic restart after power failure
Heating operation (Heat pump operation option)
etc...
-CONTINUOUS CAPACITY CONTROL-
PRECISE TEMPERATURE
CONTROL
WATER TEMPERATURE
Start
Outlet Water Temperature
Load Up 1
(Quick cooling)
Load Up 2
Neutral =2qC Standard
(Minimum 0.5C)
Load Down
TIME
-CONVENTIONAL STEP CONTROLRestart

WATER TEMPERATURE
Combination of "Continuous Capacity

Control Compressor" and "HITACHIs
unique electronic controls" enable the
Chiller to control outlet water temperature
precisely, independent of cooling load.
This control benefits not only airconditioning but also industrial process
use.
Outlet
Temperature
1st step
Final step
Temperature
Band 7qC
(normally)
1/4
2.4. HEAT EXCHANGER
Less Refrigerant (Small Internal Volume)
-Clean (Stainless Steel)
-High efficiency (closer approach temperature)
Plate type heat exchanger can provide improved cooling
capacity for R407C
PLATE TYPE HEAT EXCHANGER

The new Samurai Chillers are equipped with plate type
Heat Exchangers, which have many advantages when
compared with conventional Shell & Tube heat
exchanger as described beside:
PLATE
CAPACITY (%)
SHELL & TUBE
2.5. NEW ELECTRONIC EXPANSION VALVE
This unit is equipped with an electronic expansion valve to

provide sophisticated control under any temperature
condition.
The electronic expansion valve provides reduced electrical
power consumption compared to the classical system.
3. OPERATION INSTRUCTIONS
3.1. HITACHI WATER COOLED WATER CHILLER MODELS: RCUE 40-240 WG2
To Start the Unit.
1.Open the water inlet and outlet valves.
2.After assuring that all control switches have been cut
OFF, and the LOCAL/REMOTE switch on the
printed circuit board is in the LOCAL position, turn
ON the power switch.
3.Confirm that phases R, S and T are correctly
connected. The correct phase connection can be
checked by a phase sequence indicator. If not
correctly connected, the compressor does not start
due to activation of a reversal phase protection
device. Cut the main switch and interchange two of
three terminals, R, S and T at the main power source
terminals.
4.Set the changeover switch to cool or Heat (In case
of Heat Pump operation option)
5.Fully open the liquid line stop valves.
6.Operate the cooling (Hot) and chilled water pump.
7.Set the Dip SW at the desired temperature
8.Depress the ON push button of the operation Switch
To Stop the Unit
1.Depress the OFF push button of the operation
switch.
2.Switch OFF the main power source when the unit is
shut down for a long period of time.
Pilot Lamp
The red LED indicates the normal operation.
When the orange LED is activated, any one of the
safety devices may be functioning.
Please contact your service shop, if this condition is

detected.
Daily Checking
1.Check the power supply to ensure that it is proper.
2.Check for abnormal sounds and vibration.
3.Check the unit amperage.
4.Check the operating pressure.
Troubleshooting
Unit Does Not Start
1.Is the main switch ON?
2.Is the main fuse OK?
3.Is the cooling (Hot) and chilled water running?
4.Are the setting temperature calling for the cooling
operation?
Poor Cooling (Heating) Operation
1.Is there sufficient water supplied to the condenser
and the cooler?
2.Is the setting temperature correct?
3.Is the operating pressures normal?
Maintenance
1.Replace the oil, if it has been deteriorated
2.Clean the unit with a cleaner.
3.Clean the condenser and the water cooler . (It is
recommended that a specialist will be contacted for
this type of work.)
Remote/Local Changeover
Switch is Rear Side.
o
p
q
r
s
t
u
v
Operation Switch
Oil Sight Glass
Check valve
Power Wiring Supply
Electrical Box
Water Condenser
Water Cooler
Compressor
Name
w
x
y
z
{
|
}
~
Pressure Relief Valve
High Pressure Switch
Economizer (only for 80, 150, 240 HP)
Solenoid Valve (only for 80, 150, 240 HP)
Liquid Sight Glass
Drier
Liquid Line Stop Valve
Electronic Expansion valve
Name
STRUCTURE DRAWING OF HITACHI WATER COOLED-WATER CHILLER UNIT (Example: RCUE80WG2)
COMPONENTS OF CHILLER
4. COMPONENTS OF CHILLER
4.1. STRUCTURE DRAWING
HITACHI Water cooled Water Chiller (Example of 1 Compressor Chiller)
4/5
5/6
PREPARATION INITIAL CHECK
5. PREPARATION INITIAL CHECK

5.1. INITIAL CHECK
Required Materials
Measure and Architectural Information Regarding
Installation Location
Installation Location
Confirm that the final installation location is provided
with convenient piping and wiring work. Strong water
runoff should be avoided.
Installation Space
Check for obstacles which hamper maintenance work in
the space specified in Fig.1.
Foundation
Check to ensure that the foundation is flat, level and
sufficiently strong, taking into account the maximum
foundation gradient (Fig. 2) and the unit weight balance.
Confirm elevation provision for the unit on a solid base
with an iron frame or concrete curbs shown in chap. 5.4.
In order to obtain proper clearance beneath the unit for

on-the-ground installation, where foundation bolts
should be sunk into concrete.
Unit
Check to ensure that the unit has been transported
without damage. File a damage claim with the
transportation companies if mishandling due to
transportation company negligence is suspected.
Transportation
Secure the route to the final installation location by
confirming the dimensions, (Refer to the Unit General
Data in Catalogue).
5.2. PLACING THE UNIT
DANGER:
-Do not install the unit outdoors. If installed outdoor,
an electrical leakage will occur, since the unit has

not been designed for dew protection
-If leakage is detected, stop the unit and contact the
installer or a service shop. Do not use a naked fire
near the refrigerant gas. If a naked fire is utilised
near the refrigerant gas, refrigerant is turned into a
harmful phosgene compound.
Chiller
Unit
WARNING:
This unit is operated with refrigerant R407C, which

is non-flammable and non-poisonous. However,
refrigerant itself is heavier than the atmosphere so
that a floor is covered with refrigerant gas if
refrigerant is leaked. Therefore, keep good
ventilation to avoid choke during servicing.
CAUTION:
Check to ensure that valves are correctly opened. If

not opened, serious damage will occur to the
compressor due to an abnormally high pressure.
Fig. 1
Maximum Foundation Gradient
The unit should be installed in an upright

position within the gradient shown in below Fig.
Tools And Instruments
Pincers, Wrenches, Facilities to Transport and

Place The Unit.
Transportation
Transportation the unit as close to the final

installation location as practical before
unpacking is accomplished. Provide adequate
facilities to place the unit on the foundation, with
sufficient consideration given to those
individuals performing the installation.
Unpacking
10 mm
5 mm
Follow the instructions marked on the packing.

Fig. 2
5/7
5.3. CENTRE OF GRAVITY

Centre of Gravity
Centre of Gravity
4
Control Panel
Model
40
50
60
80
Location
RCUE - WG2
100
120
150
180
200
240
Weight Distribution (kg)
1
2
3
4
225
175
215
165
230
175
225
170
245
190
250
190
275
410
215
415
285
415
225
415
Operating Weight
430
440
445
450
445
465
470
485
600
700
625
730
610
710
645
750
620
735
675
795
(kg)
780
800
875
1000
1765
1865
2655
2715
2825
1655
Location of Center of Gravity (mm)

Dimension
A
Dimension
B
538
531
522
509
521
516
509
511
508
501
490
490
490
482
815
813
803
1262
1263
1259
5/8
5.4. SERVICE SPACE AND FOUNDATION
RCUE 40, 50, 60, 80WG2
RCUE 100, 120, 150WG2
RCUE 180, 200, 240WG2
Detail Of Foundation
N
1
2
3
4
5
6
Name
4- 26 (Mounting Holes)
Bottom Frame
Vibration proof Rubber Mat (4 positions)
Vibration proof Rubber Mat (1 mat per position) OPTION
N
7
8
9
10
11
12
Name
Washer
Nut
Foundation bolt (M20)
Rubber Bush (OPTION)
Steel Plate (1 mm)
Concrete
5/9
5.5. TRANSPORTATION BY RIGGING

5.5.1. TRANSPORTATION BY RIGGING
Hook wire cables and apply field-supplied spreader bars
on the top of the unit (see below figure) to prevent the
unit from damage due to cable scratches. The unit
should remain in an upright position even during rigging.
The wire cable to rig the unit shall be three times
stronger than the unit weight. Check to ensure that the
rigging bolts are tightly fixed to the unit. The rigging
angle shall be greater than 60 as shown. The weight of
the unit is indicated on the unit label.
DANGER:
Do not stand below the unit when rigging.
CAUTION:
Put clothes between wires and the unit to avoid

damages.
N
1
2
3
4
5
5.5.2. TRANSPORTATION BY ROLLER

When rolling the unit, put at least 6 equal-sized rollers
under the base frames. Each roller must carry both the
outer frames, and must be suited to balance the unit
(see the centre of gravity in page 5/7).
Name
60 (or more)
Electrical Box
4 x 30 Rigging Holes
Spreader Bar (Field supplied)
Lifting Bracket (Field supplied)
5.5.3. DECLINING THE UNIT DURING

TRANSPORTATION
WARNING:
Do not decline the unit more than an angle of 15

as shown in the figure during transportation. If
declined more than an angle of 15, the unit may
fall down.
Smaller than 15
6/10 INSTALLATION
6. INSTALLATION
6.1. ELECTRICAL WIRING
Tools and Instruments
One Set of Wiring tools and Electrical Tester

(Clamp Meter)
Schedule Check
WARNING:
- Confirm that the field-selected electrical
components (main power switch, fuses, wires,

conduit connections, wire terminals and others)
are properly selected according to the Electrical
Data in this Technical Catalogue, and ensure that
they comply with national and local codes.
- It is recommended that the main power switch be
locked in the OFF position, to prevent against
accidental supply of power during equipment
servicing.
- Check to ensure that an earthling wire is correctly
connected to the unit. This wire protects from an
electric shock. Utilisation of an earth leakage
breaker is necessary.
4.Firmly connect the wires with wire terminals to unit

screw terminals R, S, T and N according to below
figure.
5.Connect the wires between the power source and the
field-supplied magnetic switches.
6.Consider that the main power source will not be left
turned OFF, easily, because it is necessary to
energise the oil heater even during unit stoppage.
Main Power Wiring Procedures
Confirm that electrical power is not being

supplied to the installation location prior to any
electrical installation work.
1.Install the field-supplied main switch box (es) at a
properly selected location.
2.Install conduit connectors in the hole for the power
wiring.
3.Lead main power wires and the earthling wire
through the connector to the screw terminals for
main power and earthling in the magnetic switch box.
The neutral wires for 380/50 Hz and 415 V/50 Hz
power supply should also be led through the
connector.
N
1
2
3
4
5
Name
Main Power/Terminal Board (R,S,T,N)
Electrical Box
Main Power Switch
Main Power Wiring
Earth Wiring
Control Wiring
Connect the interlock wiring and control wiring between
the unit terminals and the magnetic switches for the
water pumps, according to the wiring label. The main
connection to terminal N is required.
INSTALLATION
N
1
2
3
4
5
6
7
8
9
10
11
12
Name
In case of remote control operation this wire
shall be removed.
R Phase
Neutral
Low Voltage / Remote Control
Run/Stop Signal
Alarm Signal
Alarm Lamp
Pump Interlock
Pump operation
Remote Control Switch (RSW-A) (OPTION)
2,3 cycles
3 cycles
N
13
14
15
16
17
18
19
20
21
22
6/11
Name
2 nd. Setting Temperature
External Thermostat Operation
Operation Mode (OPTION)
Only used for:
-Diff. Water Pressure switch (OPTION)
-Flow Switch (OPTION)
Force Compressor
Load Operation
Free Cooling
Output signal (Only cycle N 1)
In case of individual indication without Remote
Control Switch
Customer wiring
Force compressor load
Setting of low voltage control
NOTE:
1.All the setting shall be performed before Power ON.
2.Remote / Local Change over Switch on Operation
Switch shall be set, to Remote.
3.Terminals 1 ~/21 are for AC220-240V,Terminals
A ~D are for DC24V. Terminals E ~F are
H-link (Low signal)
6/12 INSTALLATION
6.2. WATER PIPING
When piping connections are performed:
1. Connect all pipes as close as possible to the unit, so
that disconnection can be easily performed when
required.
2. Connect the condenser and water coolers in the
same unit to the same common water piping.
3. It is recommended for the piping of the chilled water
inlet and outlet that flexible joints be utilised, so that
vibration will not transmit.
4. Whenever permissible, sluice valves should be
utilized for water piping, in order to minimize flow
resistance and to mantain sufficient water flow.
5. Proper inspection should be performed to check for
leaking parts inside and outside the system, by
completely opening the condenser and chilled water
inlet and outlet valves to the condenser and water
cooler.Additionally, equip valves to the inlet and outlet
piping.Equip an air purge cock and a drain cock on
the water piping. The cock handle should be removed
so that the cock can not be opened under normal
circumstances. If this cock is opened during
operation, trouble will occur due to water blow-off.
6. Sufficiently perform insulation to keep the chilled

water piping cool and to prevent sweating of the
piping.
7. Under the condition where the ambient temperature
is low in winter, there is a case where equipment and
piping will become damaged during the shutdown
periods at night, because the water in the pump or
piping will be frozen. To prevent freezing of the water,
it is effective to operate the pumps even during
shutdown period.
HITACHI Chiller has the pump ON/OFF operation
control (see Wiring Diagram) water from piping.
Additionally, in a case where measures such as water
draining are difficult, utlize antifreeze mixture of
ethylene glycol type or propylenen glycol type.
8. The common water pipes (Inlet/Outlet of condenser
and cooler, field supplied, should be connected to
condenser and cooler directly.
CAUTION:
-Never use an antifreeze mixture of the salt type,
because it possesses strong corrosion

characteristics, and water equipment will be
damaged
-This product is equipped with plate type heat
exchangers. In the plate heat exchanger, water
flows through a narrow space between the plates.
Therefore, there is a possibility that freezing may
occur if foreign particles or dusts are clogged. In
order to avoid this clogging, provide a. 20 mesh
water strainer at the inlet of condenser and chilled
water piping near the product. A 20 mesh water
strainer is available as an option.
Condensing (Hot) Water Outlet
Condensing (Hot) Water Inlet
Chiller
Cooled Water Inlet
Cooled Water Outlet
NOTE:
HITACHI chiller has the pump ON/OFF operation control (see wiring diagram)
N
1
2
3
4
Name
Pressure Gauge
Strainer
Flexible Joint
Valve
INSTALLATION
6/13
CAUTION:
In case of connecting some units to the same

water piping, design the water piping so that the
water distribution to each unit is equal (refer to
figure below) Imbalance of water distribution may
cause a serious damage like a water freezing in
the heat-exchanger.
Chiller Unit
Water Pump
Heat Load
Side
6.3. MINIMUM INTERNAL SYSTEM WATER VOLUME

To ensure the cooling operation at least 5 minutes
without interruption, the internal chilled water volume in
the piping system should be greater than the minimum
volume as shown below.
MODEL RCUE WG2

Condenser Water
Flow Range
NOTE:
Minimum internal system water volume written below
is for standard ON/OFF differential, minimum internal
system water volume shall be increased by the
setting of differential
.
40
50
60
80
100
120
150
180
200
240
Max.
m /h
48.1
57.4
69.8
82.3
114.9
139.6
157.8
186.2
214.9
246.8
Min.
m3/h
14.3
17.1
20.7
24.7
38.0
41.4
47.4
56.0
64.0
74.2
Max.
3
m /h
38.6
45.9
55.8
66.6
91.9
111.4
127.8
150.8
172.3
199.9
0.42
0.51
0.61
0.73
1.01
1.23
1.41
1.66
1.89
2.20
Chilled Water Flow Range

Minimum Internal
System Water Volume
Internal Volume in Water Cooler
Liter
15.1
16.7
21.5
23.9
44.8
44.8
44.8
64.4
64.4
71.6
Internal Volume in Condenser
Liter
14.8
18.6
23.9
27.6
40.2
49.4
49.4
71.6
71.6
82.7
6.4. WATER CONTROL
CAUTION:
When industrial water is applied for chilled water

and condenser water, industrial water rarely
causes deposits of scales or other foreign
substances on equipment. However, well water or
river water may in most cases contain suspended
solid matter, organic matter, and scales in great
quantities. Therefore, such water should be
subjected to filtration or softening treatment with
chemicals before application as chilled water.
It is also necessary to analyse the quality of water by

checking pH, electrical conductivity, ammonia ion
content, sulphur content, and others, and to utilise
industrial water only if problem is encountered through
these check.
The following is the recommended standard water
quality.
6/14 INSTALLATION
Item
Standard Quality
pH (25 C)
Electrical Conductivity (mS/m) (25C)
(2)
{S/cm} (25 C)
Chlorine Ion (mg CI/I)
2
Sulphur Acid Ion (mg SO4 /I)
The Amount of Acid Consumption (pH 4.8)
(mg CaCO3/I)
Total Hardness (mg CaCO3 /I)
Calcium Hardness (mg CaCO3 /I)
Silica L (mg SIO2 /I)
Reference Quality
Total Iron (mg Fe/I)
Total Cupper (mg Cu/I)
Sulphur Ion (mg S2/I)
Ammonium Ion (mg NH4+/I)
Remaining Chlorine (mg CI/I)
Floating Carbonic Acid (mg CO2/I)
Index of Stability
Chilled Water System

Circulating
Water
Supply Water
(20 C Less
than)
Tendency (1)
Corrosion
Deposits
of Scales
6.8 ~ 8.0
6.8 ~ 8.0
Less than 40
Less than 400
Less than 30
Less than 300
Less than 50
Less than 50
Less than 50
Less than 50
Less than 50
Less than 50
Less than 70
Less than 50
Less than 30
Less than 70
Less than 50
Less than 30
Less than 1.0
Less than 0.3
Less than 1.0

Less than 0.1
It shall not be detected.
Less than 1.0
Less than 0.1
Less than 0.3
Less than 0.3
Less than 4.0
Less than 4.0
6.8 ~ 8.0
-
NOTE:
1. The mark in the table means the factor concerned with the tendency of corrosion or deposits of scales.
2. The value showed in {} are for reference only according to the former unit.
INSTALLATION
6.5. BMS CONNECTION
6.5.1. SYSTEM
BMS connection is available by using
HARC70-CE1(OP), optional BMS interface unit.
Upper Monitoring Device
Upper Monitoring Device
LonWorks
HARC70-CE1 OP
LonWorks
H-Link
HARC70-CE1
H-Link
Chiller 1
Chiller 1
Chiller 2
Chiller 3
Chiller 4
One interface HARC70-CE1 can connect up to 4

Chillers from a remote place using H-Link connection
(Hitachi communications protocol).
Protocol used by HARC70-CE1 (OP) is LonWorks. It can
connect only one Chiller.
Physical channel connection with interface is FTT-10
6.5.2. SIGNAL
Control Operation
State Monitoring
ON/OFF Chiller
All HARCS
Outlet Water Setting
All HARCS
ON/OFF
All HARCS
Chilled Water Outlet Setting
All HARCS
Chilled Water Outlet Temperature
All HARCS
Chilled Water Inlet Temperature.
All HARCS
Alarm Codes
All HARCS
Operation Status
Discharge Pressure 1,2
All HARCS
Only HARC OP
Suction Pressure 1,2
Only HARC OP
Discharge Temperature 1,2
Only HARC OP
Suction Temperature 1,2
Only HARC OP
Compressor Status (ON/OFF) 1,2
Only HARC OP
Outlet Water Temp. 1
Only HARC OP
Water Temp. In Evap. Backside 1
Only HARC OP
6/15
6/16 INSTALLATION
6.5.3. CAUTION ON USE HARC70-CE1 (OP)

Please use it correctly according to the following
"CAUTION ON USE.
As for the following:
HARC indicate HARC70-CE1 or
HARC70-CE1 OP
Monitoring Device indicate upper connecting
device for supervise , and Control Panel indicate
Control panel of Chiller unit.
SNVT Indicate Standard Network Variables Types
1.Install HARC in a grounded metal box.
2.Install a short circuit breaker in the power supply of
HARC.
3.The transmission line between HARC and Chiller unit
should be 0.75mm2 twisted-Pair cable. If it is not
used, then it cannot communicate between HARC and
Chiller unit, and it does not work properly.
4.After an abnormal transmitting occurs between HARC
and Chiller unit, and Chiller unit stops, in the case of
operation starting by the hand operation, then once
turn off Chiller units power supply, and turn on the
power supply. If it isnt carried out, then Chiller unit
keeps the condition of transmission alarm.
5.After an abnormal transmitting occurs between HARC
and Chiller unit, and Chiller unit stops, in the case of
operation starting by Monitoring Device, then transmit
an operation order after you transmit a stop order
once. If it isnt carried out, it can't start.
6.After Chiller unit, under control by HARC, is stopped
by the control panel, and operation is done from the
Monitoring Device, then transmit an operation order
after you transmit a stop order once. If it isnt carried
out, it cant start.
7.Don't set the setting temperature to Chiller unit, under
control by HARC, by the control panel. If it is done, the
setting temperature is changed. And, as for the setting
temperature, which changed in this case, transmit to
Monitoring device.
8.After the setting temperature is changed by Monitoring
Device, in the case of turned off Chiller units power
supply, set the setting temperature by Monitoring
device again. If it isnt carried out, then the setting
temperature becomes to the temperature by setting
control panel.
9.If power failure occurs in Chiller unit, under control by
HARC, it may not revert to the condition before the
power failure. Try to detect that the operation
condition of Chiller unit changed, by the Monitoring
Device. If Chiller unit stopped due to the power failure,
then transmit an operation order from the Monitoring
Device after the power supply restoration. And,
transmit the setting temperature, mode from the
Monitoring device. If it isnt carried out, and then
Chiller unit is stopping, and the setting temperature,
mode is the initialisation value by Chiller unit.
10.When SNVT, which is transmitted from HARC, is
used by other control device, premise that there is
two minutes delay between the transmitting SNVT
and the movement Chiller unit . If it isnt premised,
then a problem may occurs in the control system.
11.Don't interrupt the power supply of HARC when you

use SCPT in HARC. Even if it exceeds
MaxSendTime, when SNVT is not transmitted from
HARC, and SNVT is transmitted below with the
setting value of MinSendTime, then transmit SCPT
again . If it isnt carried out, SCPT value continues
maintaining 0.
12.If the setting of control panel change Remote to
Locally, and set Remote again, then set the setting
temperature and mode from the Monitoring Device
again. If it does not set, then the setting temperature
and mode continue maintaining the initialisation value
by Chiller unit.
13.When the abnormal transmitting occurs between the
Monitoring Device and HARC, then the condition of
the Monitoring Device may not correspond with the
condition of HARC. Set MaxSendTime and try that
the condition of the Monitoring Device corresponds
with the condition of HARC in the interval of
MaxSendTime .
14.It can't be used with the except for stop signal of
input terminal of Chiller unit .
6.5.4. DIMENSIONAL DRAWING AND

SPECIFICATIONS OF HITACHI GATEWAY
(MODEL HARC70-CE1/HARC70-CE1 0P)
Structural Drawing
Terminal Cover
After Open
Down
After Open
ID number of NEURON CHIP
On Rear Side of Cover
Mounting Dimensions
Mounting by Screw
Mounting on DIN Rail
Center Line of DIN Rail
INSTALLATION
System Wiring
Gateway
Chiller Unit
n1
Description
Wire Size
Power Supply
Power Wire AC 220/240V
(Field Supplied)
2mm shielded
Connection Wiring Between Chiller Signal Wiring DC 5V

(Field Supplied)
0.75mm twisted-pair cable

Max. length 1000m
Ground Earth Wire

(Field Supplied)
Connection Wire Between LonWorks Signal Wire DC 5V

(Field Supplied)
Marking of Terminals
Mark
POW
Indication
Red: Power Supply (AC220/240V)
Green: Lighted During
Transmission Between LONWORKS
Yellow: Lighted During
Transmission Between Chiller
IRP
PAC
Wiring Procedures
Power Line
Section
1220-240V Power
Source HARC70-CE1(OP)
Wiring Method
Remark
AC / AC / E
AC / AC / E
Earthing Wire
Control Circuit
LON / H-LINK
Upper System HARC70-CE1(OP)
Non-polar
LON / H-LINK
HARC70-CE1(OP) Water Chillers
Non-polar
6/17
6/18 INSTALLATION
Network Variables and Setting (HARC70-CE1)
Chiller
Number
Water
Cooled
Condenser
less
Air
Cooled
Air
Heat
Pump
SVNT
Number
Name
Type
LONMARK
SNVT No
Description
Contents
nv0
nviChillerEnable_0
SNVT_switch
95
On/Off Order
Byte 1: Value 0 (Fixed)

Byte 2: State 0/1 = STOP/RUN
nv1
nviCoolSetpt_0
SNVT_temp_p
105
Cool Water Temperature

Setting
2 Bytes: -2000 ~ 2500 = -20 ~ 25 C
nv2
nviMode_0
SNVT_hvac_mode
108
Operation Mode Setting
nv3
nviHeatSetpt_0
SNVT_temp_p
105
Hot Water Temperature Setting
nv4
nvoOnOff_0
SNVT_switch
95
On/Off state
nv5
nvoActiveSetpt_0
105
105
Temperature Setting
Operation Capacity (Not used
for continous capacity)
Chilled outlet temperature
1 byte:
1 = HVAC_HEAT (Heating)
3 = HVAC_COOL (Cooling)
2 bytes: 3000 ~ 6000 = 30 ~ 60 C
2 Bytes: -2000 ~ 6000 = -20 ~ 60 C
nv6
nvoActualCapa_0
nv7
nvoLvgCHWTemp_0
nv8
nvoEntCHWTemp_0
SNVT_temp_p
105
Chilled inlet temperature
nv9
nvoAlarmDescr_0
SNVT_str_asc
36
Alarm code
nv10
nvoChillerStat_0
SNVT_chlr_status
127
Chiller Status
nv11
untest_0
nv12
untest_1
nv13
untest_2
SNVT_press (Not
Available)
30
NOT USED
NOT USED
nv14
untest_3
nv15
nviChlrEnable_1
SNVT_switch
95
nv16
nviCoolSetpt_1
SNVT_temp_p
105
nv17
nviMode_1
SNVT_hvac_mode
108
On/Off Order
Setting
Same than nv0
Same than nv2

Same than nv3
Same than nv1
nv18
nviHeatSetpt_1
SNVT_temp_p
105
nv19
nvoOnOff_1
SNVT_switch
95
On/Off state
Same than nv4
nv20
nvoActiveSetpt_1
105
Same than nv5
105
Temperature Setting
Same than nv7

Same than nv8
nv21
nvoActualCapa_1
nv22
nvoLvgCHWTemp_1
SNVT_temp_p
SNVT_lev_percent
(Not Available)
SNVT_temp_p
nv23
nvoEntCHWTemp_1
SNVT_temp_p
105
nv24
nvoAlarmDescr_1
SNVT_str_asc
36
Alarm code
Same than nv9
nv25
nvoChillerStat_1
SNVT_chlr_status
127
Chiller Status
Same than nv10
nv26
untest_4
nv27
untest_5
nv28
untest_6
SNVT_press (Not
Available)
30
NOT USED
NOT USED
nv29
untest_7
nv30
nviChlrEnable_2
SNVT_switch
95
nv31
nviCoolSetpt_2
SNVT_temp_p
105
nv32
nviMode_2
SNVT_hvac_mode
108
On/Off Order
Setting
Same than nv0
Same than nv2

Same than nv3
81
NOT USED
Same than nv1
nv33
nviHeatSetpt_2
SNVT_temp_p
105
nv34
nvoOnOff_2
SNVT_switch
95
On/Off state
Same than nv4
nv35
nvoActiveSetpt_2
105
Same than nv5
105
Temperature Setting
Same than nv7

Same than nv8
nv36
nvoActualCapa_2
nv37
nvoLvgCHWTemp_2
SNVT_temp_p
SNVT_lev_percent
(Not Available)
SNVT_temp_p
nv38
nvoEntCHWTemp_2
SNVT_temp_p
105
nv39
nvoAlarmDescr_2
SNVT_str_asc
36
Alarm code
Same than nv9
nv40
nvoChillerStat_2
SNVT_chlr_status
127
Chiller Status
Same than nv10
nv41
untest_8
SNVT_press (Not
Available)
nv42
untest_9
30
NOT USED
NOT USED
nv43
untest_10
30
nv44
untest_11
30
nv45
nviChlrEnable_3
SNVT_switch
95
nv46
nviCoolSetpt_3
SNVT_temp_p
105
nv47
nviMode_3
SNVT_hvac_mode
108
On/Off Order
Setting
Same than nv0
Same than nv2

Same than nv3
81
Provide an interval of
5 seconds of more
between each setting
Those values are

updated each 60
seconds.
When setting points
are changed from
NOT USED
HARC change to
2 Bytes: -2000 ~ 6000 = -20 ~ 60 C
related point is
detected not waiting
60 seconds.
If no water chiller is
2 Bytes: -2000 ~ 6000 = -20 ~ 60 C
connected these
values are set to 0
31 Bytes: 4 first bytes alarm description as shown in chiller.
5th byte always 0. Others undefined
3 bytes:
Byte 1: Chiller Run Mode
0: Chlr_Off (OFF Mode) 2:Chlr_Run (Run Mode)
Byte 2: Chiller Operation Mode
1: HVAC_HEAT (Heating) 3:HVAC_COOL (Cooling)
A: HVAC_FREE_COOL (Cooling Thermostat Off)
Byte 3: Chlr State
bit 0: 0/1 (no alarm / alarm)
bit 1: 0/1 (run not available / run available)
bit 2: 0/1 (central / local)
bits 3 ~ 7: Not used
SNVT_temp_p
SNVT_lev_percent
(Not Available)
SNVT_temp_p
81
Remarks
NOT USED
Not used
5 seconds of more
Those values are
updated each 60
seconds.
When setting points
are changed from
HARC change to
related point is
60 seconds.
connected these
values are set to 0
Not used
5 seconds of more
Those values are
updated each 60
seconds.
When setting points
are changed from
HARC change to
related point is
60 seconds.
connected these
values are set to 0
30
Same than nv1
nv48
nviHeatSetpt_3
SNVT_temp_p
105
nv49
nvoOnOff_3
SNVT_switch
95
On/Off state
Same than nv4
nv50
nvoActiveSetpt_3
105
Same than nv5
105
Temperature Setting
Same than nv7

Same than nv8
nv51
nvoActualCapa_3
nv52
nvoLvgCHWTemp_3
SNVT_temp_p
SNVT_lev_percent
(Not Available)
SNVT_temp_p
nv53
nvoEntCHWTemp_3
SNVT_temp_p
105
nv54
nvoAlarmDescr_3
SNVT_str_asc
36
Alarm code
Same than nv9
nv55
nvoChillerStat_3
SNVT_chlr_status
127
Chiller Status
Same than nv10
nv56
untest_12
nv57
untest_13
nv58
untest_14
NOT USED
NOT USED
nv59
untest_15
nv60
nciMaxSendTime
nv61
nciMinSendTime
81
NOT USED
Not used
5 seconds of more
Those values are
updated each 60
seconds.
When setting points
are changed from
HARC change to
related point is
60 seconds.
connected these
values are set to 0
30
SNVT_press (Not
Available)
30
30
30
NOT USED
INSTALLATION
6/19
Network Variables and Setting (HARC70-CE1 OP)

Water Condenser
Air
Air Heat
Cooled
less
Cooled Pump
SVNT
Number
Name
Type
LONMARK
SNVT No
Description
Contents
nv0
nviChillerEnable_0
SNVT_switch
95
On/Off Order

nv1
nviCoolSetpt
SNVT_temp_p
105

Setting
2 Bytes: -2000 ~ 2500 = -20 ~ 25 C
nv2
nviMode
SNVT_hvac_mode
108
1 byte:
1 = HVAC_HEAT (Heating)
3 = HVAC_COOL (Cooling)
2 bytes: 3000 ~ 6000 = 30 ~ 60 C
2 Bytes: -2000 ~ 6000 = -20 ~ 60 C
nv3
nviHeatSetpt
SNVT_temp_p
105
nv4
nvoOnOff
SNVT_switch
95
On/Off state
nv5
nvoActiveSetpt
105
nv6
nvoActualCapa
nv7
nvoLvgCHWTemp
SNVT_temp_p
SNVT_lev_percent
(Not Available)
SNVT_temp_p
105
Temperature Setting
nv8
nvoEntCHWTemp
SNVT_temp_p
105
nv9
nvoAlarmDescr
SNVT_str_asc
36
Alarm code
nv10
nvoChillerStat
SNVT_chlr_status
127
Chiller Status
n11
nvoDpress1
SNVT_press
30
Discharge Pressure 1
n12
nvoDpress1
SNVT_press
30
2 Bytes:0~30000 = 0~3,000 kPa
n13
nvoDpress1
SNVT_press
30
2 Bytes:0~30000 = 0~3,000 kPa
81
NOT USED
2 Bytes: -2000 ~ 6000 = -20 ~ 60 C

31 Bytes: 4 first bytes alarm description
as shown in chiller. 5th byte always 0.
Others undefined
3 bytes:
Byte 1: Chiller Run Mode
0: Chlr_Off (OFF Mode) 2:Chlr_Run (Run
Mode)
Byte 2: Chiller Operation Mode
1: HVAC_HEAT (Heating)
3:HVAC_COOL (Cooling)
A: HVAC_FREE_COOL (Cooling
Thermostat Off)
Byte 3: Chlr State
bit 0: 0/1 (no alarm / alarm)
bit 1: 0/1 (run not available / run
available)
bit 2: 0/1 (central / local)
bits 3 ~ 7: Not used
2 Bytes:0~30000 = 0~3,000 kPa
n14
nvoDpress1
SNVT_press
30
2 Bytes:0~30000 = 0~3,000 kPa
n15
nvoDpress1
SNVT_press
30
2 Bytes:0~30000 = 0~3,000 kPa
n16
nvoDpress1
SNVT_press
30
2 Bytes:0~30000 = 0~3,000 kPa
n17
nvoSpress1
SNVT_press
30
Suction Pressure 1
2 Bytes:0~30000 = 0~3,000 kPa
n18
nvoSpress2
SNVT_press
30
Suction Pressure 2
2 Bytes:0~30000 = 0~3,000 kPa
n19
nvoSpress3
SNVT_press
30
Suction Pressure 3
2 Bytes:0~30000 = 0~3,000 kPa
n20
nvoSpress4
SNVT_press
30
Suction Pressure 4
2 Bytes:0~30000 = 0~3,000 kPa
n21
nvoSpress5
SNVT_press
30
Suction Pressure 5
2 Bytes:0~30000 = 0~3,000 kPa
n22
nvoSpress6
SNVT_press
30
Suction Pressure 6
2 Bytes:0~30000 = 0~3,000 kPa
n23
nvoDtemp1
SNVT_temp_p
105
Discharge Temp 1
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n24
nvoDtemp2
SNVT_temp_p
105
Discharge Temp 2
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n25
nvoDtemp3
SNVT_temp_p
105
Discharge Temp 3
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n26
nvoDtemp4
SNVT_temp_p
105
Discharge Temp 4
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n27
nvoDtemp5
SNVT_temp_p
105
Discharge Temp 5
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n28
nvoDtemp6
SNVT_temp_p
105
Discharge Temp 6
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n29
nvoSTemp1
SNVT_temp_p
105
Suction Temp 1
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n30
nvoSTemp2
SNVT_temp_p
105
Suction Temp 2
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n31
nvoSTemp3
SNVT_temp_p
105
Suction Temp 3
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n32
nvoSTemp4
SNVT_temp_p
105
Suction Temp 4
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n33
nvoSTemp5
SNVT_temp_p
105
Suction Temp 5
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n34
nvoSTemp6
SNVT_temp_p
105
Suction Temp 6
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n35
nvoODtemp
SNVT_temp_p
105
Outdoor Temperature
2 Bytes: -12700 ~12700 = -127 ~ 127 C
n36
nvoCompOnOff1
SNVT_state x 16
83
Compressor Information
32 Bytes: Byte 1: b0: 0/1 = STOP/RUN
n37
nvoCompOnOff2
SNVT_state x 16
83
n38
nvoCompOnOff3
SNVT_state x 16
83
n39
nvoCompOnOff4
SNVT_state x 16
83
n40
nvoCompOnOff5
SNVT_state x 16
83
n41
n42
n43
n44
n45
n46
n47
n48
nvoCompOnOff6
nvoLvgCHWTemp
1
nvoLvgCHWTemp
2
nvoLvgCHWTemp
3
nvoLvgCHWTemp
4
nvoLvgCHWTemp
5
nvoLvgCHWTemp
6
unused 1
n49
Provide an interval of 5
seconds of more between
each setting
2 Bytes: -2000 ~ 6000 = -20 ~ 60 C
Remarks
SNVT_state x 16
83
SNVT_temp_p
105
Outlet Water Temp 1
2 Bytes: -12700 ~12700 = -127 ~ 127 C
SNVT_temp_p
105
Outlet Water Temp 2
2 Bytes: -12700 ~12700 = -127 ~ 127 C
SNVT_temp_p
105
Outlet Water Temp 3
2 Bytes: -12700 ~12700 = -127 ~ 127 C
SNVT_temp_p
105
SNVT_temp_p
105
SNVT_temp_p
105
SNVT_temp_p
unused 2
n50
Those values are updated

each 60 seconds.
When setting points are
changed from HARC change
to related point is detected
not waiting 60 seconds.
connected these values are
set to 0
105
Water Temp in Cooler BackSide

1
2
3
NOT USED
NOT USED
NOT USED
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
unused 3
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
n51
unused 4
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
n52
unused 5
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
n53
unused 6
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
n54
unused 7
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
n55
unused 8
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
n56
unused 9
SNVT_temp_p
105
NOT USED
NOT USED
NOT USED
nv57
nciMaxSendTime
nv58
nciMinSendTime
2 Bytes: -12700 ~12700 = -127 ~ 127 C

2 Bytes: -12700 ~12700 = -127 ~ 127 C
2 Bytes: -12700 ~12700 = -127 ~ 127 C
NOTE:
Set and use the variables in accordance with the above tables. (The variables based on "Chiller Part of LonMarkFunction
Profile", however, some function and setting range have limitation)
6/20 INSTALLATION
Space Requirements
Specifications
Item
NOTE:
1.Before operating this gateway, initial settings by a
system integrator for the local LonWorks system
are necessary.
2.This gateway is designed to be connected with
LonWorks network, and will not function by itself
when it is not connected.
3.The power lines and the signal lines shall be
separated with a minimum distance of 15cm.
4.It is necessary to set and adjust the Chillers and
gateway before operating the system.
5."LonWork" "LonMark" are trademarks of Echelon
Corporation registered in the USA and other
countries.
Specifications
Connection
Capacity
Power Supply
Power
Consumption
Ambient Condition
Temperature
Relative Humidity
Net weight
Colour
Material of Box
Mounting Method
Mounting Location
Accessories
Transceiver
Warranty
Maximum 4H-Link PCBs of Hitachi

Chiller
AC 1-PH, 220~240V10% 50/60Hz
Maximum 10W
0-45C
10-80% (with condition of no
condensation)
0.6kg
Grey (Munsell 5Y7/1 or similar)
ABS resin molding material
Wall Mount (By 2 x M4 Screws), or on
DIN Rail (35mm)
In Weather and Dust-Proofed Control
Panel
Core x 1, Capacitor x 1
Using FTT-10A
No warranty shall be applied for the
control and operation of the upper
"LonWorks" side.
Hitachi's liability shall cover only Hitachi
Chillers, this gateway, and accessibility
by "LonWorks"
Transmitting Setting (On Chiller Control PCB)

Operation
Before shipment, No. 1 pin of DSW10 is set at
ON side
In case that Chiller Unit quantity in the same HLink is 2 or more, set No. 1 pin of DSW10 at the
OFF side from 2nd Unit. If only one Chiller Unit
is used, no setting is required.
In case of applying high voltage to the terminal
TB1 (E,F), the fuse on the PCB is cut.
In such a case, first connect the wiring to TB1
(E,F) and then turn ON DSW-2
DSW
ON
OFF
ON
OFF
ON
OFF
INSTALLATION
6/21
6.6. CSC-5S
CSC-5S is a remote controller for Hitachi Water Chillers
6.6.1. SYSTEM
CSC-5S allows the individual control of a Chiller Unit as well as it allows a centralized and grouped controls of a maximum
number of 8 chillers.
8 Chillers (Maximum)
CSC-5S
6.6.2. SIGNAL
Indication code
Indication Content
Unit
ON/OFF unit operation

Setting Temperature COOL
Setting Temperature HEAT
Remark
Control Data
C1Pd ~ C2Pd
C1Ps ~ C2Ps
Operation Mode
Discharge Pressure
Suction Pressure
C1td ~ C2td
Discharge Gas Temperature
C1ts ~ C2ts
Suction Gas Temperature
C1tr ~ C2tr
Liquid Refrigerant Temperature
CEL
Inlet Water Temperature
CoL
CcoL
Individual Water Piping Outlet Temperature
tSC
Setting Temperature of Chilled Water
tSH
Setting Temperature of Hot Water
tSCd
Setting Analog Temperature of Chilled Water
Not available
tSHd
Setting Analog Temperature of Hot Water
Not available
dF
Differential Setting
tA
Ambient Temperature (Not available)
Crno
CvEr
rno
ROM No. of Chiller Unit

Version No. of Chiller Unit
ROM No. of Controller (CSC-5S)
MPa
MPa
Control
Monitoring
Indicate Max. 6
Refrigerant Circuit
Data
The display contents

depend on chiller
unit.
Monitoring Data
6/22 INSTALLATION
6.6.3. CAUTION ON USE OF CSC-5S
Follow strictly instructions of CSC-5S Installation Manual. This controls requires power supply ~1 220-240 V.
6.6.4. DIMENSIONAL DRAWING AND SPECIFICATIONS OF CSC-5S

Structural Drawing
Mounting Dimensions
System Wiring
Max. 8 Chiller Units
Chiller Unit
Chiller Unit
Power Supply
To TB2 of other Controller
Twist Pair Cable 1P-0.75mm2
INSTALLATION
CSC-5S LAYOUT
SPACE REQUIREMENTS
More than 50 mm
Do not run the power line and the control line

through the same conduit tube.
PowerLine
Power Supply Part
Screw
(x2)
Control
Line
Switch Box with Cover
(Field-Supplied)
TRANSMITTING SETTING (ON CHILLER CONTROL PCB)

Operation
DSW
Before shipment, No. 1 pin of DSW10 is set at ON side
ON
OFF
In case that Chiller Unit quantity in the same H-Link is 2 or more, set No. 1 pin of
DSW10 at the OFF side from 2nd Unit. If only one Chiller Unit is used, no setting is
required.
ON
OFF
In case of applying high voltage to the terminal TB1 (E,F), the fuse on the PCB is cut.
In such a case, first connect the wiring to TB1 (E,F) and then turn ON DSW-2
ON
OFF
6/23
6/24 INSTALLATION
6.7. INSTALLATION FINAL CHECK

Inspect the installation work according to all documents and drawings. Table below shows the minimum check points.
6.7.1. INSTALLATION WORK CHECK LIST

1. Is the unit solidly mounted and levelled?
2. Is the installation location adequate?
4. Is the electrical wiring system adequate?

Wire Size
Tightened Connections
Indoor Installation
Switch Size
Operation Control Devices
Space for Maintenance Work
Fuse Size
Safety Devices
Noise and Vibration
Voltage and Hz
Interlock
Sunshine and other Heat Sources

Appearance
3. Is the water piping system adequate?
Tube Size
Water Drain
Length
Water Control
Flexible Joint
Air Purge
Insulation
Pressure Control
Strainer
Common Pipes (for 3 cycles)
5. Have the R, S and T phases of the water Chiller

correctly been connected to the R, S and T phases of
the main power source?
6. Are the stop valves for the condenser liquid line open?
7. Have the packing glands and the cap nuts for the stop
valves been tightened?
8. Is BMS connected correctly and operate as decided?
TEST RUNNING
7/25
7. TEST RUNNING
7.1. PREPARATION
Tools and instruments
High Pressure Compound Gauge. Low

Pressure Compound Gauge. Electrical Tester
and General Tools.
CAUTION:
- Switch On the main power switch, and energise the
oil heater for 12 hours before start-up, to sufficiently

warm the oil.
- Check to ensure that valves are correctly opened. If
not opened, serious damage will occur to the
compressor due to an abnormally high pressure.
- Remove the foreign particles and substances from
the water piping without going through the water
coolers and condensers, and cleaning the water
strainer filter before test runningg. Check to ensure
that no foreign particle and substance exists in the
water piping
7.2. TEST RUNNING

Test running should be performed as follows, when the unit
is wired according to the HITACHI standard wiring label.
1. Switch ON the field-supplied pump and the cooling
tower, and the pump and cooling tower will be started
immediately. Check the condition and operation state of
these components
2. Fully open the liquid line stop valve.
3. Set the operation switch to "ON", and the compressor
will be started in a few minutes after this operation,
according to the following Operation Sequence Chart
(Refer to pages 36 to 38).
Test running should be accomplished as follows.
CAUTION:
When the unit is wired according to the HITACHI

standard wiring shown on the wiring label. Switch ON
the main power switch, and energize the oil heater for
12 hours before start-up to sufficiently warm the oil.
Each rotation direction of two rotors in the compressor
is fixed so that a reversal phase protection device is
equipped.
However, the rotation direction should be checked with
a following method:
Confirm that phases R, S and T for the compressor is
correctly connected. The correct phase connection
can be checked by a phase sequence indicator. If
not, the compressor does not start due to activation of
the reversal phase protection device.
- Cut the main switch and interchange two of three
terminals, R, S and T on the main terminals at the field

connection side in the unit.
1. Operate the pump for chilled water and other
auxiliary equipment such as fan coil units and air
handling units.Check to ensure that the chilled water
flows sufficiently and that other auxiliary equipment
operate properly.
2. Set the switch at the desired temperature.
3. Depress the ON push button, the compressor will
be started.
4. After system operation becomes stabilized, check the
discharge and suction pressures by 7-segment on
control panel.
5. Check to ensure that the thermostat functions
properly.
6. Check to ensure that the control and protective
devices function properly.
7. Starting timer and unload-starting timer are set at five
(5), thirty (30) seconds, respectively, in accordance
with operation characteristics. Therefore, local
adjustment should be avoided.
NOTE:
- A loud sound occurs when this compressor is
stopped after the normal operation. However, this

sound indicates no abnormalities and stops within a
few seconds by the activation of the check valve.
This sound is due to the reverse rotation of the
screw rotors, resulting from the pressure difference
between the discharge and the suction pressure.
- Each compressor may show the different values of
running current due to individual capacity control for
each compressor. This is not abnormal.
8/26 CONTROLLER ADJUSTMENT
7.3. INSTRUCTIONS AFTER TEST RUNNING

When the test running is completed, please instruct
customers about operation and periodic maintenance
methods before leaving the unit, by using Installation,
Operation and Maintenance Manual. A special attention is
required to the following caution:
CAUTION:
-Do not cut off the power source switch during the
operating season. When the power source switch is

cut off, the oil heater for screw compressor is not
energised, and the compressor might be damaged
due to oil foaming at starting.
-When the operation season starts after long
disconnection of the power source switch, please turn
on the power source switch 12 hours before starting
operation.
8. CONTROLLER ADJUSTMENT
LED
PUSH
BUTTON
SWITCH
7 SEGMENTS
SWITCH POSITION
ON
OFF
ON
OFF
ON
OFF
High Cut Check (Fan Stop for Checking)

(NOT AVAILABLE)
Chilled Water Temperature Setting

(STANDARD: "+07")
Defrosting Set by Ambient Temperature (Heat Pump)

(NOT AVAILABLE)
Continuous Capacity Control Setting

(STANDARD)
Compressor starting Delay Time

(STANDARD: 3 min)
Mode Set Switch A / H-LINK address

(DEPEND ON MODEL)
Manual Defrost (Heat Pump)

(NOT AVAILABLE)
Optional Function B
(STANDARD: ALL OFF)
Optional Function C
(STANDARD: ALL OFF)
Mode Set Switch B

Local/Remote Changeover Switch
(STANDARD: "Local")
Cool/Heat Changeover Switch

(STANDARD: "Cool", Heat is available only for Heat Pump
operation Option)
Current Limitation
(Not Available)
Neutral Zone Setting

(STANDARD: "3")
Hot Water Temperature Setting for Heat Pump

(STANDARD: "45", Available only for Heat Pump operation
option)
Optional Function A (Outernals signals, Self-Checking mode)

(STANDARD: ALL OFF)
Pump Operation (STANDARD: OFF)
CONTROLLER ADJUSTMENT
8/27
8.1. CONTROL SYSTEM

Electrical Operation Control advanced HITACHI Water
Chillers are as follows.
Capacity Control
Printed Circuit Board
All models are equipped with an unloading system for each

compressor, in order to adjust the cooling capacity and to
provide precise temperature control for the chilled water,
coupled with electronic thermostats.
A micro-processor, relays and electronic components are

mounted on the Printed Circuit Board. Increased reliability
is assured due to the elimination of mechanical parts and
wires. This board contains various function by applying
micro-processor as follows:
Control Panel
ON switch, OFF switch, Power Supply Lamp, Operation
Lamp, Alarm Lamp, Operation/Alarm Indicator for each
refrigerant cycle and check switch are mounted in the
Control Panel. The Control Panel is located at a position
where easy access is available. Operation/Alarm indicator
can display individual alarm codes such as High-Cut, LowCut etc. this function is very useful for detecting what alarm
has occurred. Check switches are for checking chilled
water temperature and alarm occurrence data. Chilled
water temperature setting switches, ON/OFF Differential
Setting Switches, Remote-Local Switch and so on are
located at the rear side of Control Panel, in order not to
access during operation.
Operation Hour-Meter
This hour-meter indicates the sum of the compressor
operation
Screw Compressor Cycling Protection Circuit.

The electronic timer of the screw compressor cycling
protection (ccp) connected in the compressor control circuit
delays the screw compressor restarting period for
approximately three (3) minutes for No.1 compressor, four
(4) minutes for No.2 compressor, five (5) minutes for No.3
compressor.
Electronic Thermostat Circuit.
The electronic thermostat senses chilled water outlet
temperature, and operate capacity control solenoid valves
of HITACHI screw compressor.
Screw Compressor Reversing Protection Circuit.
This circuit is composed of a reverse-phase protection
devices, preventing reverse operation of the screw
compressor, because the screw compressor definitely
cannot be operated in the wrong direction, due to the
misconnection of the main power phases.
Restart after Short Period Power-Failure.
In the case that a power failure shorter than 2 seconds
occurred, compressors can be restarted automatically
within 3 minutes after power supply.
If power failure longer than 2 seconds occurres,
compressor also can be restarted by selection switch
setting.
Power Supply
All models need only single power supply . Control circuit is
powered from main power circuit. For remote control, pump
interlock and pump operation, see the diagram of
"Customer Wiring".
8/28 CONTROLLER ADJUSTMENT

8.2. CONTROLLER ADJUSTMENT
Layout of control panel of printed circuit board is shown in
the Figure of the last page.
Setting functions are followings:
Continuos Capacity Control Setting

Switch=DSW5
Chilled Water Outlet Temperature Setting

Switch = RSW1 and RSW2
Temperature Band for Stop Setting Switch

= 1 degree is standard. The figure 1 and 2 of the DSW5
switch are already set at figure 1 = ON side, 2 = OFF side.
The locations at the figure 1 and 2 of the DSW5 mean as
follows.
= 7C for chilled water outlet temperature is

recommended. The RSW1 and RSW2 dials are already
set at 7 and 0.
Setting at the figures from 3 to 9 of the RSW2 dial
should not be permitted.
Hot Water Outlet Temperature Setting

Switch = RSW3 and RSW4 (Available only for Heat
Pump operation option) = 45C for hot water Outlet
temperature is recommended. The RSW3 and RSW4
dials are already set at 5 and 4.
Current limitation = RSW5, 6, 7
Figure
1
2
1
2
1
2
1
2
Location
ON ON ON OFF OFF ON OFF OFF
Band(degree)
0.5
1.0
1.5
2.0
Temperature Band for Restart Setting Switch
= 2 degree is standard. The figure 3 and 4 of the DSW5
switch are already set at figure 3 = ON side, 4 = OFF side.
follows.
Figure
3
4
3
4
3
4
3
4
Location
Band(degree)
1.0
2.0
3.0
4.0
= The RSW5, RSW6 and RSW7 should not be

permitted.
Neutral Zone Setting Switch = RSW8

= 2 degrees is standard. The RSW8 dial is already set at
3 = 2 degrees.
The figures at the RSW8 dial means as follows:
Figure
0 1 2 3 4 5 6 7 8 9
Band(degree) 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Continuous Capacity Control Setting Switch =
DSW5Definition of Special Terms.

Water
Temperature
Load Up 1 Mode
Load Up 2 Mode
9C
Water Outlet
Temperature
Set by
RSW8
Neutral Zone
Water Inlet
Temperature
Inlet Water Temp.
when system is
stopped with
Thermos Off mode
7C
Setting Temperature
Set by
DSW5,
1&2 pin
Load Down Mode

6C
Thermo Off
Standard
Setting
Figure
5
5
Location
ON OFF
Band(degree) 1.0 3.0
Output Signal Time for Load-up 1 Mode Setting Switch
= 12 seconds is standard. The figure 6 of the DSW5 switch
is already set at ON side.
The locations at the figure 6 of the DSW5 mean as follows.
Figure
6
6
Location
ON OFF
Time(second) 12 24
10C
Set by
DSW5,
5 pin
Differential Temperature of Load-up 2 Mode Setting Switch

= 1 degree is standard. The figure 5 of the DSW5 switch is
already set at ON side.
The locations at the figure 5 of the DSW5 mean as follows.
Set by
DSW5,
3&4 pin
Output Signal Time for Load-up 2 and Load-down Mode

Setting Switch
= 2 seconds is standard. The figure 7 and 8 of the DSW5
switch are already set at figure 7 = ON side,
8 = ON side.
The locations at the figure 7 and 8 of the DSW5 means as
follows.
Figure
7
8
7
8
7
8
7
8
Location
Time(second)
2
4
6
8
Interval of Output Signal Time for Load-up 2 and Loaddown Mode Setting Switch.
=60 seconds is standard. The figure 9 and 10 of the DSW5
switch are already set at figure 9=ON side, 10=ON side.
The locations at the figure 9 and 10 o f the DSW5 mean as
follows.
Figure
9
10
9
10
9
10
9
10
Location
Time(second)
60
90
120
30
CONTROLLER ADJUSTMENT
Setting of Compressor Cycling Protection

Start = DSW2
* Time Delay Starting for Compressor Setting Switch *
The compressor will be started after this setting time.
= 3 minutes is standard. The figure 1 and 2 of the DSW2
switch are already set at figure 1 = OFF side, 2 = OFF side.
follows.
Figure
Location
Time(minute)
1
2
1
2
1
2
1
2
0.5
6
10
3
Manual Set Switch A = DSW3

* Compressor Forcedly Stop Mode Setting Switch *
Switches "DSW3-1" is for No.1 compressor, "DSW3-2" for
No.2, and "DSW3-3" for No.3.
If necessary to stop any compressors, turn these switches
(DSW3-1, DSW3-2 and DSW3-3 to the OFF side, the
compressors corresponding to these switches are turned to
the OFF side will be stopped).
The figures of the DSW3 switch are initially set as follows
depend on the compressor quantity.
This switch is for servicing, therefore, all the compressors
shall be ON for normal operation.
Figure
Location
Model
1
2
3
ON
OFF OFF
1 Comp. System
Figure
Location
Model
1
2
3
ON
ON
ON
3 Comp. System
1
2
3
ON
ON
OFF
2 Comp. System
Setting at the figures from 4 to 10 of the DSW3 switch

should not be permitted (always at OFF side).
Note: The figures 2 and 3 of DSW3 which are Not
corresponding to the equipped compressor number are
always turned to the OFF side.
Manual Set Switch B = DSW4

The figure 2, 6 and 7 of the DSW4 switch must be turned to
the ON side.
Setting at the figures 1,3, 4, 5 and 8 of the DSW4 switch
should not be permitted (always at OFF side).
8/29
The figures 9 and 10 of DSW4 switch are for compressor

size setting as follows.
Figure
Location
Compressor
9
10
OFF ON
40 HP
9
10
ON OFF
50 HP
9
10
ON ON
60 HP
9
10
OFF OFF
80 HP
Selection Switch for Cooling/ Heating

Operation = SW8
The SW8 selection SW is used for selecting cooling or
heating operation. However, Standard model in this series
are for cooling only. So that Heating function is available
only for Heat Pump operation option.
Turn SW8 to the upper side for cooling operation or lower
side for heating operation.
Selection Switch for Local/ Remote Operation

= SW6
= Local operation is standard. So that the SW6 selection
switch is turned to the upper side.
If Remote operation is required, the SW6 selection switch
is turned to the upper side.
Selection Switch for Local/ Remote Pump

Operation = SW7
= The SW7 selection switch is turned to the lower ("OFF")
side as remote setting.
If local operation is required, the SW7 selection switch is
turned to the upper side.
Other Switches = SW5, DSW6, RSW9 and

DSW1
This control panel is equipped with other switches:
The SW5 selection switch for chilled water/brine water, so
that this switch must be turned to the upper side
(water). DSW6 and RSW9 for operation mode and
setting change of these switches are not available.
The figure 2 of DSW6 must be turned to the upper side.
It is recommended that the setting is not changed at site.
Also, the DSW1 switch is equipped with. This switch is
used for only checking, resulting in easy troubleshooting.
9/30 SELF-INSPECTION FUNCTIONS
9. SELF-INSPECTION FUNCTIONS
9.1. ALARM INDICATION
SEG1
Alarm Indication
If the unit is operated under abnormal conditions, an alarm
code(refer to the table below) is indicated and the "Alarm"
LED is lighted.
Function of 7-Segment Light Emitted Diode on Control
Panel is as shown in the table below.
Code
No.2
Cycle
No.1
Cycle
SEG2
. .
7 Segments on
Control Panel
Content
No.3
Cycle
Activation of High Pressure Switch
Activation of Low Pressure Control
Activation of Thermal Relay for Compressor or Malfunction of Auxiliary Relay Arn

Activation of Discharge Gas Thermistor
Activation of Compressor Internal Thermostat
Excess Low Temperature of Cooler Inlet Refrigerant
Activation of Suction Gas Thermistor
Phase Abnormally (Only for 3 cycle unit)
Failure of Water Outlet Thermistor (Only for 3 cycle unit)
Activation of Freeze Protection Control (Only for 3 Cycle Unit)
Failure of Cooler inlet Refrigerant Thermistor (Open / Short)
Failure of Discharge Gas Thermistor (Open / Short)
Failure of Thermistor set before Expansion Valve
Failure of Water Outlet Thermistor (Rear side of Water Cooler)
Failure of Suction Gas Thermistor (Open / Short)
Failure of Discharge Gas Pressure Sensor (Open / Short)
Failure of Suction Gas Pressure Sensor (Open / Short)
Failure of Hot Water Outlet Temperature Thermistor (Only for 3 Cycle Unit of Heat Pump
Operation Option)
Phase Abnormally (Only for 1 and 2 Cycle Unit)
Failure of Water Inlet Temperature Thermistor
Failure of Water Outlet Thermistor. (Only for 1 and 2 Cycle Unit)
Activation of Freeze Protection Control (Only for 1 and 2 Cycle Unit)
Failure of Hot Water Inlet Temperature Thermistor (Only for Heat Pump Operation Option)
Failure of Hot Water Outlet Temperature Thermistor (Only for 1 and 2 Cycle Unit of Heat
Pump Operation Option)
No Feedback Signal from Water Pump
Incorrect Operation
Error Communication between Expansion Valve PCB and Control PCB
Alarm of Excessively High Water Temperature

Alarm of Water Failure for Water Cooler (Differential Pressure Switch or Flow Switch
Option)
Alarm of Water Failure for Condenser (Differential Pressure Switch or Flow Switch Option)
Activation of Additional Protection Device
Error Communication between Chiller and Remote Controller (If CSC-5S is connected.)
Retry Operation (by Alarm Cx-9x or Cx-Lx, x: Cycle No.)
- : Flickering
SELF-INSPECTION FUNCTIONS
9/31
9.2. NORMAL INDICATION

If the unit is operated under a normal operation condition,
the operation code (refer to the table below) is indicated on
7-Segment LEDs of the control panel.
No.1
Cycle
Code
No.2
Cycle
Content
No.3
Cycle
Power Supply, After Stoppage
Cooling Operation
Heating Operation (Only for Heat Pump Operation Option)

Stoppage by Thermo-OFF or Retry by Alarm Cx-5x
Pump Operation, Warning of Pump Feedback
Initializing Electronic Expansion Valve
9.3. FUNCTION FOR INDICATION OF OPERATION CONDITION

Function for Indication of Operation Condition
The setting temperature, chilled water temperature sensed
at the thermistor, the setting differential temperature and
the last alarm code are digitally indicated on the control
panel.
The Alarm Code
Occurrence Data
Memory Data
Indication in alarm
(Latest Data only)
Normal Operation
Condition
"88" "Co" "oF"
o Press the check "" and "" switches

Checking
Indication
simultaneously for more than 3 sec.

It is changed to the normal mode by
pressing the "" and "" switches
simultaneously for more than 3 sec.
again.
p Press the check "" switch for more than
3 sec.
pressing the "" switch for more than 3
sec. again.
q Press the check "" switch for more than
Second Water
Temperature Setting
3 seconds at the time to display latest

alarm coad.
r Press the check "" switch for more than

3 seconds.
Note:Each indication mode shall be changed from the normal mode.
Indication Mode of Alarm Occurrence Data o

The content of abnormal stoppage including activation of
safety devices is memorised and indicated on the
control panel
Alarm Occurrence Data (Max.10 data)
2 3
In case of No. 1 cycle high

pressure alarm occurrence

2 3

In case of No. 2 cycle high

pressure alarm occurrence

pressing the "" switch for more than 3
sec. Again.
NOTE:
If an abnormal operation is occurred under this
indication mode, this indication mode is changed to
the alarm indication mode.

Checking Indication q
Back to "CPU ROM numbre"
Alarm Code Occurred Last
(no alarm)
Discharge Pressure (MPa)
Suction Pressure (MPa)
Discharge Gas Temperature (Option) (C)
Suction Gas Temperature (C)
Evaporating Temperature (C)
Water Inlet Temperature (C)
4 +
(N 1 Cycle $+ = 1.92 MPa)
4 +
4 +
4 6
(N 1 Cycle $6 = 0.42 MPa)
4 6
4 6
7 +
(N 1 Cycle 7+ = 82C)
7 +
7 +
7 6
(N 1 Cycle 76 = -2C)
7 6
7 6
7 5
(N 1 Cycle 75 = -2C)
7 5
7 5
"
Average Water Outlet Temperature (C)
Water Outlet 1 Temperature (C)
Setting Water Outlet Temperature (C) (Cooling)
Setting Water Outlet Temperature (C) (Heating)
Second Setting Water Outlet Temperature (C) (Cooling)
Second Setting Water Outlet Temperature (C) (Heating)
3 "
3 "
3 "
7 6
7 6

7 6 +
7 6 +

& $
" +
2 &
Hold
" +
Compressor Capacity Control (C)
Load up
3 "
" +
9/33
+ -
Setting Neutral Zone Temperature Difference (C)
+ #
Load down

Thermo-off
Alarm Control Status

Control Status
Control Status
Discharge Pressure Control
Not available
Suction Pressure Control
Not available
Different Pressure Control
Load Down Control (Water

Outlet Temp.)
Freeze Protection Control
Not Available
Compressor Start Control
Discharge Temperature
Control
Discharge Temperature Retry
Liquid Bypass (Not Available)
Not available
Not Available
Control Status
ux
sw
$
3
Compressor start control
$
3
Suction pressure control activated
4
3
Discharge pressure control activated
Memory Data Indication in Alarm
Data is indicated same as Checking Indication.

In addition the checking data, below data is added.
Water Outlet Temperature (Cooler Backside) (C)
Control status
Expansion Valve Pulse
7 5
3
3
3
$
3
, 3
#
, 3

, 3
Second Water Temperature Setting
9/35
This temperature setting can provide another setting value for water temperature.
It can be changed by external signal
Second Water Temperature Setting Procedure
1)Press the check switch for more than 3 seconds.
Then, display shows the current setting value.
7 +
#
:
* This shows the setting value is 6C.

If press the check or in this mode, the display is changed to either Hot Water Temperature Setting or
Chilled Water Temperature Setting alternatively.
7 +
7 +
:
2)Press the check and switches simultaneously for more than 3 seconds.The mode is changed to setting mode.
Then, the setting value can be changed by pressing the check and switches.
However, the setting value shown on display, is not available in this moment.
Press

:
#
:
Press

:
3)Press the check and

switches simultaneously for more than 3 seconds. At the same time, the setting value
shown on display is memorized and available.
7 +
.
:
* The setting is changed to 9.5C.

* Hot water temperature setting change is performed by same procedure mention above.
When the wiring connection shown below, this second temperature setting is available.
Available
Not
Solenoid Valve
Time Schedule
SV11
SV12
SV13
OFF
OFF
OFF
OFF
OFF
MC1
Motor for
Compressor
OFF
OFF
OFF
ON
OFF
OFF
CLS
ON
OFF
OFF
ON
OFF
CLS
OFF
OFF
OFF
OFF
Main Power Switch

Chilled Water Pump
Condenser Water Pump
Operation Switch (ON/OFF)
Load Up
Neutral
Controller
Load Down
Safety Devices
N 1
Power Supply Lamp
Operation Lump
Alarm Lumpr
Oil Heater
CH1
Control Devices
Control Stage
OFF
OFF
OFF
OFF
ON
ON
ON
CLS
ON
OFF
OFF
ON
3min.
ON
OFF
OFF
OFF
ON
ON
ON
ON
CLS
ON
ON
OFF
ON
15%
15%
30sec.
ON
ON
OFF
OFF
OFF
OFF
5sec.
ON
ON
ON
CLS
ON
ON
OFF
OFF
DLT
(ULD)
ON
ON
ON
CLS
ON
ON
OFF
OFF
STA
(ULD)
Starting Control
ON
ON
ON
O
CLS
ON
ON
OFF
OFF
DLT
(FLD)
CLS
ON
ON
OFF
OFF
DLT
(FLD)
ON
ON
ON
O
ON
ON
ON
O
CLS
ON
ON
OFF
OFF
DLT
(ULD)
15%99%
OFF
ON
OFF
ON
ON
ON
O
CLS
ON
ON
OFF
OFF
DLT
(ULD)
15%99%
OFF
OFF
OFF
OFF
ON
OFF
15%
ON
ON
ON
O
CLS
ON
ON
OFF
OFF
DLT
(ULD)
ON
OFF
OFF
OFF
ON
ON
ON
O
CLS
ON
ON
OFF
ON
ON
ON
ON
O
CLS
ON
ON
OFF
OFF
DLT
(ULD)
15%99%
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
O
OPN
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
CLS
ON
OFF
OFF
ON
Safety Devices
CLS: Close, OPN: Open, STA: Star, DLT: Delta

ULD: Unload, FLD: Full Load
Minimum 3min.
15%- 100% 100%

99%
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
O
CLS
ON
ON
OFF
OFF
DLT
(ULD)
Capacity Control
OFF
OFF
OFF
100%
ON
ON
ON
O
CLS
ON
ON
OFF
ON
DLT
(FLD)
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
CLS
ON
OFF
OFF
ON
Shut Down
OFF
OFF
OFF
OFF
CLS
OFF
OFF
OFF
OFF
OFF
OFF
OFF
-
10/36
CONTROL SYSTEM
10.CONTROL SYSTEM
Standard Operating Sequence for RCUE 40WG2, RCUE 50WG2, RCUE 60WG2 and RCUE 80WG2
Time Schedule
Solenoid Valve
Motor for
Compressor
SV11
SV12
SV13
SV21
SV22
SV23
MC2
MC1
Main Power Switch

Chilled Water Pump
Load Up
Controller
Neutral
Load Down
N 1
Safety Devices
N 2
Power Supply Lamp
Operation Lump
Alarm Lumpr
CH1
Oil Heater
CH2
Control Devices
Control Stage
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CLS
CLS
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
CLS
CLS
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
CLS
CLS
ON
OFF
OFF
ON
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
15%
ON
ON
ON
CLS
CLS
ON
ON
ON
OFF
ON
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(FLD)
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(FLD)
15%100% 100%
99%
DLT
DLT
DLT
(ULD) (FLD) (FLD)
15%100% 100%
99%
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(ULD)
15%99%
DLT
(ULD)
15%99%
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(ULD)
OFF
ON
OFF
OFF
ON
ON
15%
DLT
(ULD)
15%
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(ULD)
ON
OFF
OFF
ON
OFF
OFF
OFF
0FF
15%99%
DLT
(ULD)
15%99%
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(ULD)
DLT
(ULD)
15%99%
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
ON
ON
ON
O
OPN
OPN
ON
ON
ON
ON
ON
O
OPN
CLS
ON
ON
Safety Devices

15%99%
DLT
(ULD)
15%99%
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
O
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
ON
ON
ON
ON
ON
9/37
Capacity Control
The compressor which started finally will be started first.
ON
OFF
OFF
ON
OFF
OFF
15%
DLT
(ULD)
15%
ON
ON
ON
CLS
CLS
ON
ON
ON
OFF
OFF
DLT
(ULD)
30sec.
ON
OFF
OFF
ON
OFF
OFF
5sec.
15%
STA
(ULD)
ON
ON
ON
CLS
CLS
ON
ON
ON
OFF
OFF
STA
(ULD)
15%
Minimum 3min.
60sec.
ON
OFF
OFF
ON
OFF
OFF
5sec.
ON
OFF
OFF
ON
OFF
OFF
3min.
OFF
ON
ON
ON
CLS
CLS
ON
ON
ON
OFF
ON
STA
(ULD)
15%
OFF
OFF
ON
ON
ON
ON
CLS
CLS
ON
ON
ON
ON
ON
Starting Control
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
CLS
CLS
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
100%
DLT
(FLD)
100%
ON
ON
ON
O
CLS
CLS
ON
ON
ON
ON
ON
DLT
(FLD)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
CLS
CLS
ON
OFF
OFF
ON
ON
Shut Down
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CLS
CLS
OFF
OFF
OFF
OFF
OFF
CONTROL SYSTEM
Standard Operating Sequence for RCUE 100WG2, RCUE 120WG2 and RCUE 150WG2
10/37
SV11
SV12
SV13
SV21
SV22
SV23
SV31
SV32
SV33
MC3
MC2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
CLS
CLS
CLS
OFF
OFF
3 min.
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
CLS
CLS
CLS
ON
ON
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
STA
(ULD)
15%
ON
ON
ON
CLS
CLS
CLS
ON
ON
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DLT
(ULD)
15%
DLT
(ULD)
15%
ON
ON
ON
CLS
CLS
CLS
ON
ON
60 sec.
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
5 sec.
OFF
OFF
OFF
OFF
DLT
(ULD)
15%
STA
(ULD)
15%
ON
ON
ON
CLS
CLS
CLS
ON
ON
ON
ON
ON
CLS
CLS
CLS
ON
ON
30 sec.
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DLT
DLT
(ULD)
(ULD)
15%
15%
DLT
DLT
(ULD)
(ULD)
15%
15%
STA
DLT
(ULD)
(ULD)
15%
15%
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
5 sec.
ON
ON
ON
CLS
CLS
CLS
ON
ON
DLT
(FLD)
100%
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
DLT
(ULD)
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
15%-99%
15%-99%
OFF
OFF
OFF
OFF
DLT
(FLD)
100%
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
15%-99%
DLT
(ULD)
15%-99%
OFF
OFF
OFF
OFF
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
Minimun 3min.
The Compressor which started finally will be restarted first.
60 sec.
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
5 sec.
OFF
OFF
OFF
OFF
ON
ON
DLT
(ULD)
15%
ON
ON
ON
CLS
CLS
CLS
ON
ON
Starting Control
DLT
(FLD)
100%
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
15%-99%
OFF
OFF
OFF
OFF
DLT
(FLD)
15%
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
OFF
ON
ON
OFF
ON
OFF
OFF
ON
OFF
15%-99%
DLT
(ULD)
15%-99%
OFF
OFF
OFF
OFF
DLT
(ULD)
15%
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
15%-99%
DLT
(ULD)
15%-99%
OFF
OFF
OFF
OFF
DLT
(ULD)
15%
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
OFF
OFF
OFF
OFF
DLT
(ULD)
15%
DLT
(ULD)
15%
DLT
(ULD)
15%
OFF
ON
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
Capacity Control
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
15%-99%
DLT
(ULD)
15%-99%
DLT
(ULD)
15%-99%
OFF
OFF
OFF
OFF
DLT
(ULD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
15%-99%
DLT
(ULD)
15%-99%
DLT
(ULD)
OFF
ON
ON
OFF
OFF
ON
ON
ON
O
OPN
CLS
CLS
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
15%-99%
DLT
(ULD)
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
O
OPN
OPN
CLS
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
O
OPN
OPN
OPN
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
CLS
CLS
CLS
ON
OFF
DLT
(FLD)
100%
DLT
(FLD)
100%
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
DLT
(FLD)
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
CLS
CLS
CLS
ON
OFF
Shut Down

ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
O
CLS
CLS
CLS
ON
ON
Safety Devices
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CLS
CLS
CLS
OFF
OFF
CONTROL SYSTEM
Time Schedule
Solenoid Valve
Motor for
compressor
OFF
OFF
OFF
Oil Heater
OFF
OFF
ON
ON
ON
CH1
CH2
CH3
MC1
OFF
OFF
OFF
OFF
Operation Lump
Alarm Lump
ON
OFF
OFF
CLS
CLS
CLS
OFF
OFF
OFF
CLS
CLS
CLS
OFF
OFF
Main Power Switch

Chilled Water Pump
Controller
Load up
Neutral
Load down
No. 1
Safety Devices
No. 2
No. 3
Power Supply Lamp
Devices
Control Stage
10/38
CONTROL SYSTEM
Standard Operating Sequence for RCUE 180WG2, RCUE 200WG2, and RCUE 240WG2
MAINTENANCE 11/39
11. MAINTENANCE
The unit should be periodically inspected according to the
same items as those described in the paragraph titled
Test Running. In order to ensure dependable
performance and long life operation, the following
additional items should be given for particular attention.
WARNING:
If a fire accidentally occurs, turn OFF the main switch

and use an extinguisher for an oil fire and an electric
fire.
Do not operate the unit near flammable gases such
lacquer, paint oil, etc. to avoid a fire or an explosion.
Turn OFF the main switch when electrical box covers
are removed for setting the temperature. Do not
operate the unit without fixing panels.
DANGER:
CAUTION:
Perform periodical maintenance according to the

INSTRUCTIONS to maintain the unit in a good
condition.
Do not touch the parts at the discharge gas side by
hand, since the pipes at the discharge side are
heated by refrigerant and the temperature becomes
higher than 100 C.
Do not utilize this unit for cooling or heating of
drinking water or food. Comply with local codes and
regulations.
Turn OFF all the main switches if refrigerant leakage
or chilled / hot water leakage occurs. Also, if the unit
can not be stopped by the control switch, turn OFF all
the switches for power source.
Switch OFF main interruptor (MI) for any work inside

electrical box.
11.1. COMPONENTS
Compressor
Control and Protective Devices
The semi-hermetic screw compressor requires periodic

maintenance, including replacement of parts. See the
HITACHI Service Handbook for Screw Compressors, for
details.
Do not readjust the settings in the field unless the setting is

maintained at the point other than the point listed in the
table on chapter 11.
Electrical Equipment
Always pay careful attention to working voltage, amperage
and phase balance. Check for faulty contact caused by
loosened terminal connections, oxidised contacts, foreign
matter, and others.
11.2. LUBRICATION
Compressor
The compressors are charged at the factory with the
correct oil listed in Component Data and the compressor
nameplate. It is not necessary to add oil, if the refrigerant
cycle remains sealed.
11.3. DEPOSITS
Slime and other minerals in the condenser water or chilled
water tend to deposit on inside surfaces of plates over a
long period of operation. As deposits of these minerals
increase, excessive high discharge pressure or lower
operation pressure are detected, indicating evidence of
deposits on the condenser or the water cooler. The figure
in page 41 indicates the range where cleaning is required.
CAUTION:
-Cleaning of plate type heat exchangers shall be
performed by specialists. Please contact your

contractor or dealer of HITACHI.
-Clean the water strainer filter periodically according to
its clogging degree. If not cleaned periodically, the
water strainer will be broken due to an excessive
pressure to the strainer screen.
strainer at the inlet of the chilled water piping near the

product. If clogging in the plate type heat exchanger
occurs seriously, this will cause insufficient cooling
performance or local freezing in the plate type heat
exchanger. It is strongly recommended that the heat
exchanger be cleaned at the same time when the
filter is cleaned.
Pay attention to the following caution and normal
cleaning method. For details, contact your Hitachi
installer.
Water
WARNING:
-This product is equipped with plate type heat
exchangers. In the plate type heat exchanger, water

flows through a narrow space between plates.
Therefore, there is a possibility that freezing may
occur if foreign particles or dusts are clogged. In
order to avoid this clogging, provide a 20 mesh water
Refrigerant
11/40 MAINTENANCE
CAUTION:
-In the case that a cleaning agent is used adjust
-Correctly select cleaning agent depending on scales in
concentration of the cleaning Agent, cleaning period

and temperature according to the scale degree.
-In the case that acid cleaning is performed,
neutralisation treatment is required after cleaning.
Treatment for neutralisation fluid should be performed
by a waste fluid contractors.
-The cleaning agent and neutralizing agent are erosive
and stimulative against eyes, skin, mucous membrane
etc. Therefore use protection tools (protection glasses,
protection gloves, protection shoes, protection cloth,
protection mask, etc.) in order not to absorb or touch
these agents during this cleaning work.
the plate type heat exchangers. The cleaning

chemicals are different depending on fouling degree.
-This plate type heat exchanger is made of stainless
steel. Do not use a cleaning agent containing
hydrochloric acid or fluorine compound. If used, the
heat exchanger will be damaged, resulting in
refrigerant leakage.
-After cleaning with cleaning agent, clean inside of
water piping including the heat exchangers by using
clean water. Perform water treatment (preventive
treatment) in order to prevent the water circuit from
corrosion or re-adhering of scales after cleaning.
11.4. CLEANING METHOD
q
p
r
s
o
r
u
t
N
1
2
3
4
Name
Chiller Unit
Chilled Water / Inlet Piping
Acid-resistant Type Water Pump
Hose
1. Installation of Cleaning Circuit

-Stop the water Chiller unit.
-Stop the circulating water pump.
-Disconnect the connections at the chilled water inlet or
cooling water inlet and install a circulating water circuit by
using an acid-resistant type water pump.
2. Check of Circulating Circuit
Pour water in the cleaning tank and operate the acidresistant type water pump.
-Check to ensure that no water leakage exists.
-Check to ensure that the water hose is firmly fixed.
-Check to ensure that the cleaning Agent will not damage
equipment near the water Chiller even if bubbles occur
and touch them.
-Check to ensure that good ventilation is available.
-Check to ensure that no abnormal sound occurs.
3. Cleaning Work
-Discharge water in the water circuit of the air conditioning
system.
-Supply diluted cleaning fluid from the cleaning water tank
by operating the acid-resistant pump.
-Circulate the cleaning fluid for an appropriate period of
time (the operating time should be determined according
to the type of cleaning Agent, concentration and fouling
degree).
N
5
6
7
8
Name
Diluted Cleaning Fluid
Chilled Water / Outlet Piping
Cleaning Water Tank
Waste Fluid Tank
4. Waste Fluid
-Stop the acid-resistant pump.
-Put the waste fluid into the waste fluid tank.
-Supply water into the cleaning tank and operate the pump
for water cleaning.
-Put the cleaning water into the waste fluid tank as same as
the waste fluid.
-Measure pH degree by using a pH test sheet and
neutralize the waste fluid by gradually adding neutralizing
agent.
-After neutralization ask a waste fluid treatment contractors
to handle it.
5. Neutralisation Treatment in the Water Piping
-Put water into the cleaning tank.
-Operate the acid-resistant pump after air-purging.
-Measure the pH degree and gradually add neutralizing
agent until the pH reaches pH = 7.
-Operate the pump for a specified period of time for
neutralization.
-Discharge the used water.
-Operate the circulating pump and clean the circuit with
water until no fouling fluid is observed.
6. Re-starting
-Reconnect the water piping as they were so that the water
Chiller can operate.
-After cleaning, perform water treatment (preventive
treatment) in order to prevent the water circuit from
corrosion.
Area Requiring Cleaning
Saturation Line
Condenser Water Outlet Temperature (C)
Suction Gas Pressure (MPa)
Discharge Gas Pressure (MPa)
MAINTENANCE 11/41
Saturation Line
Area Requiring Cleaning
Chilled Water Outlet Temperature (C)
11.5. WINTER SHUTDOWN

When shutting down the unit for winter, clean the inside
and outside of the cabinet, and dry the unit. Pump down
the refrigerant to the condenser and close the liquid outlet
stop valves. This unit should be covered during shutdown,
in order to protect it from dust and environmental
conditions. Be sure to tighten the packing glands and the
cap nuts of the valves.
Remove the drain plug and drain all residual water from the
condenser and water cooler piping systems, as such water
may freeze during the cold season. It is very helpful to
supply brine (anti-freezer) to the piping systems.
11.6. SPRING START-UP

After any extended shutdown period, prepare the unit for
operation as follows.
1. Thoroughly inspect and clean the unit.
2. Clean the water piping lines and the strainer.
3. Inspect the pump, the cooling tower and/or regulating
valve.
4. Tighten all wiring connections and access panel.
CAUTION:
When the main switch for this unit has been at the
OFF position for an extended period of time, it should
be switched ON at least 12 hours before start-up, so
that oil in the compressor discharge casing may be
warmed enough, to prevent oil foaming by the oil
heater during start-up.
11.7. PART REPLACEMENT

Replacement of parts should be undertaken by ordering
from the HITACHI Spare Parts List.
CAUTION:
Do not replace with spare parts which are not the

equivalent.
11/42 MAINTENANCE
11.8. REFRIGERATION CYCLE
Strainer
Completely evacuate the entire cycle with a vacuum

pump.
Charge refrigerant to the refrigeration cycle by
weighing the charging cylinder. The proper refrigerant
charge is listed on the nameplate.
When charging by weight is stopped due to high
ambient temperature, close the valve and operate the
unit after circulating the chilled water through the water
cooler.
2. When Only Additional Refrigerant is Required.
Connect a gauge manifold to check joint of low pressure
side, and connect a charge cylinder to gauge manifold.
Operate the unit after circulating the chilled water.
Repeat the following procedure until pressure becomes
proper (refer to page 46)
Charge the gas refrigerant a little slowly into
refrigeration cycle from check joint for low pressure.
Check the pressure after refrigeration cycle becomes
stable.
Check for clogging each time when the refrigeration cycle

is opened.
Refrigerant Charge
Inspect the refrigerant charge of the system by checking
the discharge and suction pressures. Perform a leakage
test, if any leakage is suspected, and always perform such
a test after a refrigeration cycle component is replaced.
When refrigerant charge is required, follow the following
instructions given for two cases:
1. When Refrigerant Gas Completely Leaked.
Before charging the entire cycle must be completely
evacuated and dehydrated. A gauge manifold or
equivalent piping preparation shown in the next page is
recommended as a convenient procedure regarding
both charging and evacuation.
Fully open all the stop valves.
Connect the evacuation line to the check joints of the
high and the low pressure sides.
11.9. REFRIGERANT CYCLE DIAGRAM OF HITACHI WATER COOLED CHILLER

MODEL: RCUE 40, 50, 60, 100, 120, 180, 200WG2
Condensing Water Outlet

Design
Pressure
Condensing Water Inlet
Hydrostatic Test
Pressure
Gauge
manifold
Chilled Water
Inlet
Evacuation
Charging
Chilled Water
Outlet
Unit side
Flange Connection
Flare Connection
Solder Connection
Refrigerant Cycle
No.
1
2
3
4
5
6
7
8
9
10
11
Name
Compressor
Check Valve
Stop Valve (Option)
Water Condenser
Stop Valve
Stop Valve
Drier
Sight Glass
Electronic Expansion Valve
Water Cooler
NOTE:
R407C shall be charged by LIQUID.
No.
12
13
14
15
16
17
A
B
C
D
E
Name
Stop Valve (Option)
Pressure Sensor (Low)
Pressure Sensor (High)
Compressor Safety Valve (Option)
Compressor Dual Safety Valve (Option)
High Pressure Gauge
Low Pressure Gauge
Stop Valve
Charging Cylinder
Vacuum Pump
MAINTENANCE 11/43
MODEL: RCUE 80, 150, 240WG2
Condensing Water Outlet

Condensing Water Inlet
Design
Pressure
Hydrostatic
Test
Pressure
Gauge
manifold
Chilled
Water Inlet
Chilled
Water Outlet
Evacuation
Unit side
Charging
Flange Connection
Flare Connection
Solder Connection
Refrigerant Cycle
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Name
Compressor
Check Valve
Stop Valve (Option)
Water Condenser
Stop Valve
Stop Valve
Drier
Sight Glass
Water Cooler
Stop Valve (Option)
Pressure Sensor (Low)
No.
15
16
17
18
19
20
21
22
A
B
C
D
E
Name
Pressure Sensor (High)
Compressor Safety Valve (Option)
Compressor Dual Safety Valve (Option)
Pressure Switch
Solenoid Valve
Capillary Tube
Economizer
Strainer
High Pressure Gauge
Low Pressure Gauge
Stop Valve
Charging Cylinder
Vacuum Pump
NOTE:
R407C shall be charged by LIQUID.
CAUTION:
-Do not charge OXYGEN, ACETYLENE or other
flammable and poisonous gases into the refrigeration

cycle when performing a leakage test or an airtight
test. These types of gases are extremely dangerous,
because explosion can occur. It is recommended that
compressed air or nitrogen be charged for these
types of tests.
-Mineral deposits on water cooler plates act as thermal
insulators, and also act as resistance Against water
flow, causing the water flow to decrease running
through them, and resulting in a decreasing of the
cooling capacity. Deposits on the plates should be
inspected at regular, intervals, experience with the
water Chiller will dictate accurate inspection intervals.
-These deposits should be removed by circulating
diluted acid through the water passes after the water

has been drained. As water in different localities
contains different minerals, different acids are
required, depending upon the thickness of the
deposits.
-This unit is equipped with an operation hour meter. In
the case that the total operation time reaches 40,000
hours or 5 years pass after installation, exchange the
bearings of the compressor. For details, refer to the
Service Handbook for HITACHI Screw Compressors.
-For R407C refrigerant system, charge the refrigerant
with liquid condition to avoid its composition change.
11/44 MAINTENANCE
11.10. COMPRESSOR REMOVAL
When Removing the Compressor
Remove the compressor while completing the

following procedures.
5.Operate the water Chiller after circulating water

through the water cooler and condenser.
1.Collect all refrigerant into a condenser before this

work.
6.Stop the water Chiller when the low pressure reaches

at approximately 0.05 MPa. Do not operate at the
pressure lower than 0.05 MPa. If operated, it will
cause a damages to the compressor.
2.Turn off the switch, DSW3 of the PCB in the electrical

box in order not to operate the compressor except for
the cycle.
7.Wait for several minutes. If the low pressure increase

up to 0.15 to 0.2 MPa, repeat the above procedures 5
and 6 four or five times.
3.Circulate the chilled and cooling water sufficiently

through the water cooler and condenser, and operate
the water Chiller for 10 minutes, and check to ensure
that the oil level is maintained at a stable condition.
8.Turn OFF the power supply to the unit.

9. Remove the bolts on the discharge and suction
flanges of the compressor.
4.Stop the water Chiller and completely close the liquid

stop valve.
11.11. SAFETY AND PROTECTION CONTROL

The safety and protective devices are equipped with the
unit to ensure dependable and long life operation.
Their functions should be carefully noted, and field
adjustment is not recommended, if the setting is maintained
at the point listed in the table.
Compressor protection
1. Fuse and thermal relay equipped in the control box cut
out each compressor operation when the current to the
compressor exceeds the setting
2. The internal thermostat embedded in the motor winding
cuts out each operation, when the temperature exceeds
the setting
3. The oil heater in the compressor prevents from oil
foaming during cold starting. This heater warms the oil,
while the compressor is stopped
Refrigeration Cycle
1. The high pressure switch and low pressure control
protect Against excessive discharge pressure and
exceedingly low suction pressure. The switch and
control cut out compressor operation when discharge
pressure or suction pressure is abnormal.
2. The pressure relief valve is equipped on discharge gas
line. When high pressure exceeds the setting, gas
refrigerant will be discharged to prevent abnormal high
pressure
Water Cooler
Pump interlock, freeze protection thermostat, low
pressure control and suction gas thermostat can protect
water cooler Against water cooler freezing
MAINTENANCE 11/45
11.11.1. SAFETY AND CONTROL DEVICE SETTING
RCUE
-WG2
Model
For Compressor
Cut-Out
Low Pressure Switch
(Pressure Sensor)
40
50
60
80
100
120
150
180
200
240
Manual Reset, Non-Adjustable ( One Switch for Each Compressor Motor )

MPa
2,74 2,74 2,74 2,74 2,74 2,74 2,74 2,74 2,74 2,74
Electronic Control
MPa
0,05 0,05 0,05 0,05 0,05 0,05 0,05 0,05 0,05 0,05
Cut-Out
Internal Thermostat for Compressor
Cut-Out
Cut- In
Compressor Motor (380-415V/50Hz)
Fuse
Manual Reset, Non-Adjustable ( One Switch for Each Compressor Motor )

115 115 115 115 115 115 115 115 115 115
C
93
93
93
93
93
93
93
93
93
93
C
A
100 100 125 125 100 125 125 100 125 125
Manual Reset, Adjustable ( One Three-Phase Set for Each Compressor
Motor )
Thermal Relay
A
48
55
70
75
55
70
75
55
70
75
Manual Reset, Adjustable ( One Three-Phase Set for Each Compressor
Motor )
Magnetic circuit Protection (Option)
A
90 107 127 127 107 127 127 107 127 127
One Heater for Each Compressor Motor
Oil Heater
Capacity
W
150 150 150 150 150 150 150 150 150 150
( One for Each Cycle )
Discharge Gas (Electronic Control)
Cut-Out
140 140 140 140 140 140 140 140 140 140
C
Non-Adjustable ( One Timer for Each Compressor )
CCP Timer
Setting Time
S
180 180 180 180 180 180 180 180 180 180
Star-Delta
S
5
5
5
5
5
5
5
5
5
5
Unloading during Starting
S
30
30
30
30
30
30
30
30
30
30
( One for Each Circuit )
For Refrigerant Circuit
Setting Pressure
MPa
3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0
( One for Each Water Cooler )
Freeze Protection Thermostat
Cut-Out
2
2
2
2
2
2
2
2
2
2
C
11/46 MAINTENANCE
11.12. NORMAL OPERATING PRESSURE
Check to ensure that Chiller is operating within the working
range as shown below, after at least 15 minutes operation.
Low Pressure: The normal operating low pressure of the
water chiller is indicated in the figure below; lower than 0.3
Mpa indicates an abnormal condition.
Discharge Pressure: Normal operating discharge pressure

is indicated in the figure below; low than 0.9 Mpa or higher
than 2.2 Mpa indicates an abnormal condition
Standard Working Range
CAUTION:
Periodical Maintenance
Perform periodical maintenance according to the
INSTRUCTIONS to maintain the unit in a good
condition.
Fire
If a fire accidentally occurs, turn OFF the main switch
and use an extinguisher for an oil fire and electric fire.
Flammable Gases
Do not operate the unit near the flammable gases
such as lacquer, paint, oil, etc. to avoid a fire or an
explosion.
Service Panels and Electrical Box Cover
Turn OFF the main switch when service panels or
electrical box covers are removed for setting the
temperature.
Do not operate the unit without fixing panels.
Heated Pipe
Do not touch the parts at discharge gas side by hand,
since the pipes at the discharge side are heated by
refrigerant and temperature becomes higher than 100
C.
Use
Do not utilize this unit for cooling of drinking water or
food. Comply with local codes and regulations.
Discharge Gas
Pressure (MPa)
Suction Gas
Pressure (MPa)
For R407C
Standard Working Range
Failure
Turn OFF all the main switches if refrigerant leakage
or chilled water leakage occurs. Also, if the unit can
not be stopped by the control switch, turn OFF all the
switches for power source.
Activation of Safety Device
In the case that one of safety devices is activated and
unit is stopped, remove the cause of the stoppage
and restart the unit. The protection devices are
utilized to protect the unit from an abnormal
operation.
Therefore, if one of safety devices is activated,
remove the cause by referring the Troubleshooting
in the INSTRUCTION or call the local agency.
Fuse
Utilize a fuse with specified capacity. Do not use a
steel wire or a copper wire instead of a fuse. If an
incorrect wire is utilized, a serious accident such as a
fire will occur.
Safety Devices
Do not make a short-circuit at the protection line. If a
short-circuit is made, a serious accident will occur.
Setting of Safety devices
Do not change the setting of safety devices, if
changed, a serious accident will occur.
Do not touch any electrical parts except for the
operation switches during the operation.
Do not press the button on the magnetic switch. If
pressed, a serious accident will occur.
MAINTENANCE 11/47
11.13. TEST RUNNING AND MAINTENANCE RECORD
MODEL: RCUE
MFG. NO.
COMPRESSOR MFG. NO.
CUSTOMERS NAME AND ADRESS:

DATE:
1. Is there adequate water flow for the condenser and the water cooler?
2. Has all water piping been checked for leakage?
3. Have the cooling water pump, fan and motor been lubricated?
4. Has the unit been operated for at least twenty minutes?
5. Check Chilled Water Temperature:

Inlet
Outlet
Outlet
6. Check Condenser Water Temperature:

Inlet
7. Check Suction Line Temperature and Superheat:

Suction Line Temperature:
Superheat:
MPa
MPa
MPa
MPa
MPa
MPa
8. Check Pressure:
Discharge Pressure:
Suction Pressure:
9. Has the unit been checked for refrigerant leakage?

10. Is the unit clean inside and outside?
11. Are all cabinet panels free from rattling?
11/48 MAINTENANCE
11.14. DAILY OPERATING RECORDS

Model:
Date:
Weather:
Time of Operation Start:
Stop. (
DB
WB
Ambient Temperature
Room Temperature
Compressor
High
Pressure
Mpa
Low
Pressure
Mpa
Voltage
Current
Condenser Water
Temperature
Inlet
Outlet
Chilled Water
Temperature
Inlet
Outlet
Current for Condenser Water Pump
Current for Chilled Water Pump
Current for Cooling Tower
NOTES:
11.15. SERVICING FOR R407C REFRIGERANT SYSTEM

Refrigerant
This R407C refrigerant is HFC type so that it has a feature
of no ozone depletion. If it is mixed with another refrigerant,
the serious changing would occur on its character.
Therefore notice the following point when handling this
refrigerant.
Charge the refrigerant in LIQUID condition and NOT in
GAS. As "R407C" is geotropic mixed refrigerant, if gas
charging is performed, only the easy vaporising
refrigerant would be charged into the system and the
difficult vaporising one would be remained in the
charge cylinder.
The cylinder, gauge equipped manifold and charge hose
are only used for R407C refrigerant.
Adjust the cylinder setting to charge in liquid.

Refrigerant Oil
UX300, which R407C refrigerant is easy to blend into it, is
used for this system. The other oil is prohibited to use, so
that not to be mixed with another kind of oil at the
maintenance and service work. This oil is very hygroscopic.
Therefore minimum humidity handling is necessary.
Servicing Equipment
When servicing R407C system, servicing equipment such
as Charging Cylinder, Charging Hose, Vacuum Pump and
so on, shall not be mixed with R22 equipment to avoid
R407C composition change.
TROUBLESHOOTING 12/49
12. TROUBLESHOOTING
The following table shows efficient checking procedures for trouble.
Fault
Possible Cause
Interlock Circuit for Chilled Water Pump is
Open
Compressor Does Not Operate
Compressor Stops on High

Pressure Switch
Compressor Stops on
Overcurrent Relay
Electrical Protective Devices Are Tripped.

Incorrect Wiring Connection for Compressor
Power Source
Excessively High Discharge Pressure
Malfunction of High Pressure Switch
Excessively High Discharge Pressure and
Suction Pressure
High or Low Voltage, Single-Phase or Phase
Imbalance
Loose connection
Faulty Overcurrent Relay
Excessively Low Chilled water Outlet
Temperature
Compressor Stops on Freeze

Protection Control
Compressor Stops on Internal

Thermostat or Discharge Gas
Thermostat
Insufficient Cooling
Defective Thermistor
Shortage of Chilled Water Flow
Air in water Circuit
High or Low Voltage, Single-Phase or Phase
Imbalance
Excessive Superheat
Defective Element
Excessive High Discharge Pressure and Low
Suction Pressure
High Discharge Pressure or Low Suction
Pressure
Improper Thermostat Setting
Defective Unload Mechanism
Noisy Compressor
Slugging Due to Liquid Flooding Back to

Compressor
Worn parts
Miscellaneous Noise
Loose Fixed Screw

Trouble with the Thermistor
Unloaded Does not Function
Trouble with the Solenoid Valve

Worn Unloader Mechanism
High Discharge Pressure
Warm inlet water or Insufficient Water Flow

Through the Condenser
Gas Outlet Valve on the Condenser Not
Completely Open
Overcharged Refrigerant
Condenser Plates Coated with Scales, Slime,
Corrosion and Others
Suction Pressure is Higher than Standard
Check/Corrective Action
1.Check the pump contactor. Repair or
replace, if necessary.
2.Check for the faulty pump.
1.Remove the causes, and reset the ON
button. See the following causes.
1.Interchange two of three terminals R, S and
T at the main power source terminals.
1.See High Discharge Pressure
1.Readjust the setting or replace, if defective.
1.See High Discharge Pressure and High
Suction Pressure.
1.Check the power supply line and contactors.
Repair, if necessary.
1.Tighten the loose electrical connection or
repair, if necessary.
1.Replace it, if necessary.
1.Check for excessively low setting of the
chilled water setting knob.
1.Check for malfunction of the thermistor.
Replace, if necessary.
1.Check the rotation of the pump.
1.Purge air.
1.Check the power supply line and contactors.
Repair, if necessary.
1.Check for refrigerant leakage
1.Check the contact of the internal thermostat
during the cold condition.
1.See High Discharge Pressure and High
Suction Pressure.
1.See High Discharge Pressure and Low
Suction Pressure.
1.Readjust the setting.
1.Adjust unload mechanism. Repair or
replace unloaded parts, if necessary.
1.Check the superheat of suction gas. Keep
the superheat in proper range.
1.Check for the sound of internal parts.
Replace the compressor, if necessary.
1.Tighten the screws of all parts.
1.Adjust the setting temperature.
2.Replace the thermistor.
1.Check the coil in the solenoid valve.
2.Check oil passage for clogging.
1.Check the unloaded system parts in the
compressor.
1.Open the valve
1.Check the valves, capillary tubes and
strainer. Replace, if necessary.
1.Purge the refrigerant.
1.Clean the Condenser water plates by
chemical cleaner
1.See High Suction Pressure.
12/50 TROUBLESHOOTING
Fault
Possible Cause
Too Much Water Flowing through the
Condenser, or Water is too Cold
Insufficient Refrigerant Charge
1. Add Refrigerant.
Leakage from the Condenser Gas Outlet Valve
1. Check to determine how long it takes to

balance high and low
Liquid Refrigerant Flooding Back from the

Water Cooler, Causing Oil to Foam..
1. Check the operation and the position of

expansion valve coil. Repair or replace if
necessary.
2. Inlet water temperature is considerably
lower than the limited temperature.
Suction Pressure is lower than Standard
1. See Low Suction Pressure
High Discharge Pressure
1. See High Discharge Pressure
Refrigerant Overcharged
1. Purge the refrigerant
Liquid Refrigerant Flooding Back from the

Water Cooler
1. Check the operation and the position of

expansion valve coil. Repair or replace if
necessary.
2. Inlet chilled water temperature to the unit
is considerably higher than the standard
temperature.
Low Discharge Pressure
High Suction Pressure
Check/Corrective Action
1. Adjust the water cock or the regulating
valve.
2. Check the operation of cooling tower.
Leakage from the Condenser Gas Outlet Valve 1. Check the condenser gas outlet valve
Low Suction Pressure
Insufficient Insulation for the Chilled Water

Piping
Condenser Liquid Outlet Valve Not Completely
Open
Expansion Valve not properly controlled, or
faulty valve
Inlet Chilled Water Temperature is
Considerably lower than standard
Temperature.
Insufficient Refrigerant Charge
1. Check the insulation of the piping

1. Open the valve.
1. Check the position of Expansion Valve coil.
Repair or replace if necessary.
1. Check the insulation specifications
1. Add Refrigerant
Excessive Oil Circulatin in the System
1. Check the oil charge
Insufficient Chilled Water Flow through the

water cooler.
1. Check the chilled water piping lines for

pressure loss.
Low Discharge Pressure
1. Adjust the water shutoff valve
Scales on Water Cooler Plates
1. Clean the plates
GENERAL SPECIFICATIONS 13/51
13. GENERAL SPECIFICATIONS

13.1. GENERAL DATA
Model
Cooling Capacity *1
Power Input for Cooling *1
COP
Heating Capacity *2
Power Input for Heating *2
Height
Outer Dimension
Width
Depth
Cabinet Colour
Shipping Weight
Compressor Type
Models
Quantity
Oil Heater
Capacity Control
Cooler Type
Condenser Type
Refrigerant Type
Flow Control
Number of Independent Circuits
Oil Type
Evaporator Connection
Option Common Water Piping
Condenser Connection
Control System
Cooling Water Outlet Temperature *3
Permissible Water Pressure Max.
Cooler
Condenser
RCUE40WG2
RCUE50WG2
RCUE60WG2
RCUE80WG2
kW
kW
kW
kW
mm
mm
mm
kg
W
%
Inch
Inch
Inch
Inch
C
C
160
194
232
40
49.1
54.5
4.0
4.0
4.3
192.3
233.9
274.7
47.5
58.3
64.7
1520
1520
1520
1105
1105
1105
850
850
850
Natural Gray
750
765
830
950
Semi-Hermetic Screw Type
40ASC-Z
50ASC-Z
60ASC-Z
60ASC-Z
1
1
1
1
150
150
150
150
Continuous Capacity Control
15 100
Brazing Plate Type
Brazing Plate Type
R407C (Factory Charged)
1
1
1
1
JAPAN ENERGY FREOL UX300 (Ester)
3 Victaulic (1Inlet / 1Outlet )
Micro-Processor
(-10) 5 15
22 45 (55)
MPa
MPa
1.03
1.03
Safety and Protection Devices
Power Supply
134
33.5
4.0
161.1
39.8
1520
1105
850
Reverse Phase Protection,

Fuse and Thermal Relay for Compressor,
Internal Thermostat for Compressor, Compressor Oil Heater,
Control Circuit Fuse, High Pressure Switch, Low Pressure Control,
Discharge Gas Temperature Control,
Suction Gas Temperature Control, Freeze Protection Control
and Compressor Operation Hour Meter
3, N / 380 - 415V / 50Hz
NOTES:
*1 The nominal cooling capacities are based on the European Standard EN12055.
Chilled Water Inlet / Outlet Temperature : 12 / 7 C
Cooling Water Inlet / Outlet Temperature : 30 / 35 C
*2 The nominal heating capacities are only for Heat Pump Operation Option and based on following conditions.
Hot Water (Condenser) Inlet / Outlet Temperature : 40 / 45 C
*3 ( ) is in case of high condensing option and heat pump operation option.
13/52 GENERAL SPECIFICATIONS
Model
Cooling Capacity *1
COP
Heating Capacity *2
Height
Outer Dimension
Width
Depth
Cabinet Colour
Shipping Weight
Compressor Type
Models
Quantity
Oil Heater
Capacity Control
Cooler Type
Condenser Type
Refrigerant Type
Flow Control
Oil Type
Control System
Cooler
Condenser
RCUE100WG2
RCUE120WG2
RCUE150WG2
kW
kW
kW
kW
mm
mm
mm
kg
W
%
Inch
Inch
Inch
Inch
C
C
388
445
98.2
104.5
4.0
4.3
467.9
526.9
116.6
124.1
1700
1700
1105
1105
1465
1465
Natural Gray
1570
1670
1770
50ASC-Z
60ASC-Z
60ASC-Z
2
2
2
150 x 2
150 x 2
150 x 2
7.5, 15 100
Brazing Plate Type
Brazing Plate Type
2
2
2
Micro-Processor
(-10) 5 15
22 45 (55)
MPa
MPa
1.03
1.03
Power Supply
320
80
4.0
384.7
95
1700
1105
1465

3, N / 380 - 415V / 50Hz
NOTES:
GENERAL SPECIFICATIONS 13/53
Model
Cooling Capacity *1
COP
Heating Capacity *2
Height
Outer Dimension
Width
Depth
Cabinet Colour
Shipping Weight
Compressor Type
Models
Quantity
Oil Heater
Capacity Control
Cooler Type
Condenser Type
Refrigerant Type
Flow Control
Oil Type
Control System
Cooler
Condenser
RCUE180WG2
RCUE200WG2
RCUE240WG2
kW
kW
kW
kW
mm
mm
mm
kg
W
%
Inch
Inch
Inch
Inch
C
C
600
696
148.5
163.5
4.0
4.3
719.5
824.2
176.4
194.2
1580
1580
1105
1105
2350
2350
Natural Gray
2500
2580
2670
50ASC-Z
60ASC-Z
60ASC-Z
3
3
3
150 x 3
150 x 3
150 x 3
5, 15 100
Brazing Plate Type
Brazing Plate Type
3
3
3
Micro-Processor
(-10) 5 15
22 45 (55)
MPa
MPa
1.03
1.03
Power Supply
525
123.5
4.3
621.9
146.7
1580
1105
2350

3, N / 380 - 415V / 50Hz
NOTES:
13/54 GENERAL SPECIFICATIONS
13.2. OPTION LINE UP

Following table shows options:
(9 mark shows available)
Specifications
Low Water
Temperature
Standard
Outlet Temperature: -1 -5 (Low2)

Extended Minimum Capacity Control
Local/Remote Changeover Switch

Individual Alarm
Operation Hour Meter
Pressure Sensor (High and Low)
Pump Operation Circuit
Control
System
Non Voltage Contact for Remote indication

DC24V External Control
Short Period Power OFF Protection
Power Failure Recover Control
2 Different Temperature Setting
9
9
9
9
9
9
9
9
9
9
9
BMS Control (HARC-70CE1)/OP

CSC-5S
Number Cable
High Condensing Temperature
Heat Pump Operation
Independent Circuit
Dual safety valve

Compressor Safety Valve
Compressor Dual Safety Valve
Pressure Display (High and Low)
PED Certificate (97/23/EC)
9
9
PN 16 Flange
Water Cooler
Differential Water Pressure Switch

Water Flow Switch (Field Install)
Water Cooler Heater
Common Water Pipe
Others
Witness Test
Foundation Rubber Mats
Pump, Operation, Alarm

Level or pulse
AC 220-240V
LON-WORKS
9
9
9
9
9
Suction Valve
10 bar Water Pressure
Pump ON/OFF Contact
Discharge Valve
Refrigeration
Cycle
For Each Compressor
By Alarm Code
9
9
9
9
9
9
Remote Control Switch
Condenser
DSW 7-3 ON
Compressor Circuit Breaker Protector

Main Isolator Switch
Remarks
9
9
9
Outlet Temperature: 0 4 (Low1)

Outlet Temperature: - 6 -10 (Low3)
Compressor
Option
Standard:
Display on Operation Panel
PED: Pressure
Equipment Directive
9
9
9
9
9
9
9
With Companion Flange
(Only 180, 200 and 240 HP)
DRAWINGS 14/55
14. DRAWINGS
14.1. DIMENSIONAL DRAWINGS
RCUE 40WG2
Electrical Box
Inlet for Power

Supply Wiring
Inlet for Control Wiring

Condenser Water Outlet
Cooler Water inlet
4x Lifting Holes
Cooler Water Outlet
Condenser Water Inlet
(cooler, welding connection)

(cooler, 3 B victaulic connection)
(condenser, welding connection)
(condenser, 3B Victaulic connection)
RCUE 50WG2
Electrical Box
Inlet for Power

Supply Wiring

Cooler Water inlet
4x Lifting Holes
Cooler Water Outlet

14/56 DRAWINGS
RCUE 60WG2
Electrical Box
Inlet for Power

Supply Wiring

Cooler Water inlet
4x Lifting Holes
Cooler Water Outlet

RCUE 80WG2
Electrical Box
Inlet for Power

Supply Wiring

Cooler Water inlet
4x Lifting Holes
Cooler Water Outlet

DRAWINGS 14/57
RCUE 100WG2
Electrical Box
Condenser
Water Outlet
Cooler
Water inlet
4x Lifting Holes
Inlet for Power
Supply Wiring

Cooler Water Outlet


RCUE 120WG2
Electrical Box
Condenser
Water Outlet
Cooler
Water inlet
4x Lifting Holes
Inlet for Power

Supply Wiring

Cooler Water Outlet

14/58 DRAWINGS
RCUE 150WG2
Electrical Box
Condenser
Water Outlet
Cooler
Water inlet
4x Lifting Holes
Inlet for Power

Supply Wiring

Cooler Water Outlet

RCUE 180WG2
Electrical Box
3 x Condenser
Water Outlet
3 x Cooler
Water inlet
4x Lifting Holes
3 x Cooler
Water outlet
Inlet for Power Supply Wiring
3 x Condenser Water Inlet
DRAWINGS 14/59
RCUE 200WG2
Electrical Box
3 x Condenser
Water Outlet
3 x Cooler
Water inlet
4x Lifting
Holes
3 x Cooler Water Outlet
Inlet for PowerSupply Wiring

RCUE 240WG2
Electrical Box
3 x Condenser
Water Outlet
3 x Cooler
Water inlet
4x Lifting Holes
3 x Cooler Water Outlet

Inlet for PowerSupply Wiring
14/60 DRAWINGS
14.2. WIRING DIAGRAMS
Main Switch
POWER CIRCUIT
RCUE 80WG2
RCUE 60WG2
RCUE 50WG2
RCUE 40WG2
Models
POWER CIRCUIT FOR RCUE 40WG2, RCUE 50WG2, RCUE 60WG2 and RCUE 80WG2
DRAWINGS 14/61
Main Switch
POWER CIRCUIT
RCUE 120 WG2

RCUE 150 WG2
RCUE 100 WG2
Models
POWER CIRCUIT FOR RCUE 100WG2, RCUE 120WG2 and RCUE 150WG2
14/62 DRAWINGS
Main Switch
POWER CIRCUIT
RCUE 240 WG2
RCUE 200 WG2
RCUE 180 WG2
Models
POWER CIRCUIT FOR RCUE 180WG2, RCUE 200WG2 and RCUE 240WG2
DRAWINGS 14/63
CONTROL CIRCUIT
RCUE 80WG2
RCUE 60WG2
RCUE 50WG2
RCUE 40WG2
Models
CONTROL CIRCUIT FOR RCUE 40WG2, RCUE 50WG2, RCUE 60WG2 and RCUE 80WG2
14/64 DRAWINGS
CONTROL CIRCUIT
RCUE 150WG2
RCUE 120WG2
RCUE 100WG2
Models
CONTROL CIRCUIT FOR RCUE 100WG2, RCUE 120WG2, RCUE 150WG2
DRAWINGS 14/65
CONTROL CIRCUIT
RCUE 240WG2
RCUE 200WG2
RCUE 180WG2
Models
CONTROL CIRCUIT FOR RCUE 180WG2, RCUE 200WG2 and RCUE 240WG2
For 3 cycles units
MAIN PRINTED CIRCUIT BOARD (MASTER)
Option
For 3 cycles units
Differencial water Pressure

Switch (Condenser side)
(Option)
Differencial water Pressure
Switch (Evaporator side)
(Option)
Field
supply
For >2 cycles

units
For >3 cycles

units
14/66 DRAWINGS
MAIN PRINTED CIRCUIT BOARD
RELAYS PRINTED CIRCUIT BOARD
Free-cooling
Output signal
(only PCBd1)
Only for units with
Economizer
1
2
3
RCUE 40,50,60, 80WG2

RCUE 100,120, 150WG2
RCUE 180, 200, 240WG2
Model
Only PCBd1,3 and

PCBd2 in 3 cycles
units
Option
DRAWINGS 14/67
RELAYS PRINTED CIRCUIT BOARD
14/68 DRAWINGS
CUSTOMER WIRING
NOTE:
1. All the setting shall be performed before Power ON.
2. Remote/Local Change over Switch on Operation Switch shall be set to "Remote".
3. Terminals 1 n57 are for AC220-240V Terminals A D are for DC24V. Terminals E F
are H-Link (Low signal)
N
1
2
3
4
5
6
7
8
9
10
11
12
Name
In case of remote control operation this wire shall
be removed.
R Phase
Neutral
Low Voltage / Remote Control
Run/Stop Signal
Alarm Signal
Alarm Lamp
Pump Interlock
Pump operation
Remote Control Switch (RSW-A) (Option)
2,3 cycles
3 cycles
N
13
14
15
16
17
18
19
20
21
22
Name
2 nd. Setting Temperature
External Thermostat Operation
Operation Mode (OPTION)
Only used for:
-Diff. Water Pressure switch (OPTION)
-Flow Switch (OPTION)
Force Compressor Load Operation
Free Cooling
Output signal (Only cycle N 1)
In case of individual indication without Remote
Control Switch
Customer wiring
Force compressor load
Setting of low voltage control
DRAWINGS 14/69
PARTS LIST
(n=1~N)
Mark
Name
MC1-n
MI
CMC1-n
Compressor Motor
Main Isolator
Contactor for Compressor Motor
(Start Operation)
(Delta Operation)
Fuse holder for Compressor
Motor
CMCs1-sn
CMCD1-Dn
PFC1-n
EFC11-n3
ORC1-n
ITC1- n
Fuse for Compressor Motor
Remark
or optional
Circuit Breaker
or optional
Circuit Breaker
Overcurrent Relay for

Compressor Motor
Internal Thermostat for
Compressor
Mark
Name
Remark
EF1~5
SV11-n1
SV12-n2
Fuse
Solenoid Valve for Starting
Solenoid Valve for Load-down
6A
SV13-n3
Solenoid Valve for Load-up
TM1-n
Hour Meter
PCBA
Printed Circuit Board for Display
PCBB
Printed Circuit Board for Operation
PCBC1
Printed Circuit Board for CPU
PCBD1-Dn
Printed Circuit Board for Relay
CH1-n
Crankcase Heater
PCB F
AR,h,r,1-n
Auxiliary Relay
WPC
PSH1-n
TF 1,2,3,4,5
Transformer
PBSR2
Pd1-n
High Pressure Sensor
RL(1-n)
Ps1-n
Low Pressure Sensor
OL(1-n, C, H)
EHF1-n
Cooler Heater
Thermistor
Thermistor
Suction Gas Temperature
Thermistor
Discharge Temperature
Thermistor
Temperature Thermistor Before
Exp. Valve
Thermistor (Evap.)
Thermistor (heat)
Thermistor (heat)
Noise Filter (Ring Cores)
THMi
THMO 1,2,3
THMS1-n
THMd 1-n
THMr2 1-n
THMO 11~31
THMi (h)
THM O n(h)
MFA
OFF: 2.75Mpa
ON: Manual
Reset
PBSR1
Printed Circuit Board for Expansion

valve
Water Pressure Switch,
Water Flow Switch, Evaporator
Circuit
Push Button Switch for Starting
(REMOTE)
CMP1-2
Push Button Switch for Stoppage

(REMOTE)
Pilot Lamp for Remote Indication
(Unit Operation, Cool/Heat)
Pilot Lamp for Remote Indication
(Alarm)
Contactor for Pumps
TRP1-2
Thermal Relay for Pump
WPH
Water Pressure Switch, Water Flow

Switch, Condenser Circuit
CMT
Contactor for Tower
MVn
Electronic Expansion Valve (Exp V.)
PSWn
Pressure switch for Economizer
SVEn
Solenoid Valve for Economizer
OPTION
EHn
Electric Heater for Evaporator
OPTION
SW1~6
Switches field supplied
OPTION
Model
RCUE 40, 50, 60, 80 WG2
RCUE 100, 120, 150 WG2
RCUE 180, 200, 240 WG2
OPTION
N
1
2
3
Field
Supplied
15/70 MODEL SELECTION
15. MODEL SELECTION

15.1. SELECTION EXAMPLE
1. Determine the system requirements
Condenser Water Inlet Temperature:
Condenser Water Outlet Temperature:
Chilled Water Inlet Temperature:
Chilled Water Outlet Temperature:
Cooling Load:
2. Select Model and Read the Performance
From the cooling capacity table,
model RCUE100WG2 can be
selected with the following
performance.
Cooling Capacity:
Chilled Water Flow Rate:
Water Cooler Pressure Drop:
Condenser Water Flow Rate:
Condenser Pressure Drop:
Compressor Input Power:
32 C
37 C
12 C
7 C
300 kw
Fouling Factor
m2h C/kcal
(m2 C/kW)
Water
Cooler
Condenser
316.3 kW
54.4 m/h
36.9 kPa
68.7 m/h
67.5 kPa
83 kW
1.00
1.00
1.00
0.0001(0.086)
0.99
1.01
0
0.0001(0.086)
0.0002(0.172)
1.00
0.98
0.96
1.00
1.03
1.06
PD = x Q
Pressure Drop (kPa)
Water Flow (m/h)
Parameters (table below)
Model:
Parameter
Cooler
RCUE-WG2
40
50
60
80
100
120
150
180
200
240
0.0764
0.0648
0.0437
0.0374
0.0188
0.0188
0.0188
0.0053
0.0053
0.0046
1.912
1.912
1.912
1.912
1.897
1.897
1.897
1.912
1.912
1.912
40
50
60
80
100
120
150
180
200
240
0.0688
0.0480
0.0328
0.0358
0.0225
0.0160
0.0160
0.0041
0.0041
0.0044
1.872
1.881
1.897
1.912
1.893
1.901
1.901
1.897
1.897
1.912
Corrected Capacity = Kfc CAP

CAP:
IPT:
Kfc:
Kfi:
1.00
0.00005(0.043)
PD:
Q:
5(C) Tabulated Flow Rate (CFR)

Given Temp. Difference(C)
The corrected Flow Rate must be confirmed to be within

the working range.
2. Cooling Capacity and Compressor Input.
When the fouling factor is taken into consideration, the
cooling capacity and the compressor input will be
different from the value indicated in the cooling capacity
table.
Condenser
Kfi
4. Water Pressure Drop

Water pressure drop is given by the following formula
3. Correct the Data

1. Flow Rate
When the water Inlet/Outlet temperature difference is
not 5C, correct the flow rate by the following formula:
Corrected
Flow Rate
Kfc
Corrected Input = Kfi IPT

Tabulated Cooling Capacity
Tabulated Compressor Input
Capacity Correction Factor
Compressor Input Correction Factor
MODEL SELECTION 15/71
15.2. PERFORMANCE TABLE

RCUE40WG2
CDOT
22,0
25,0
30,0
35,0
37,0
40,0
45,0
CLOT
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
Where,
CDOT:
CLOT:
CCAP:
HCAP:
CCAP
137,9
140,9
143,9
147,0
150,0
153,1
156,1
159,1
162,2
165,2
168,3
135,4
138,5
141,6
144,8
147,9
151,0
154,1
157,2
160,3
163,5
166,6
131,3
134,6
137,8
141,1
144,3
147,5
150,8
154,0
157,3
160,5
163,8
127,3
130,6
134,0
137,4
140,7
144,1
147,5
150,8
154,2
157,6
160,9
125,6
129,1
132,5
135,9
139,3
142,7
146,1
149,6
153,0
156,4
159,8
123,2
126,7
130,2
133,7
137,2
140,7
144,1
147,6
151,1
154,6
158,1
119,1
122,7
126,4
130,0
133,6
137,2
140,8
144,4
148,0
151,7
155,3
CFR
23,7
24,2
24,8
25,3
25,8
26,3
26,8
27,4
27,9
28,4
28,9
23,3
23,8
24,4
24,9
25,4
26,0
26,5
27,0
27,6
28,1
28,7
22,6
23,1
23,7
24,3
24,8
25,4
25,9
26,5
27,1
27,6
28,2
21,9
22,5
23,0
23,6
24,2
24,8
25,4
25,9
26,5
27,1
27,7
21,6
22,2
22,8
23,4
24,0
24,5
25,1
25,7
26,3
26,9
27,5
21,2
21,8
22,4
23,0
23,6
24,2
24,8
25,4
26,0
26,6
27,2
20,5
21,1
21,7
22,4
23,0
23,6
24,2
24,8
25,5
26,1
26,7
CPD
32,5
33,9
35,3
36,8
38,3
39,7
41,3
42,8
44,4
46,0
47,6
31,4
32,8
34,3
35,7
37,2
38,7
40,3
41,8
43,4
45,1
46,7
29,7
31,1
32,5
34,0
35,5
37,1
38,6
40,2
41,9
43,5
45,2
27,9
29,4
30,8
32,3
33,9
35,4
37,0
38,6
40,3
42,0
43,7
27,2
28,7
30,2
31,7
33,2
34,8
36,4
38,0
39,7
41,4
43,2
26,2
27,7
29,2
30,7
32,2
33,8
35,4
37,1
38,8
40,5
42,3
24,6
26,1
27,5
29,1
30,6
32,2
33,9
35,6
37,3
39,1
40,9
HCAP
162,8
166,0
169,3
172,5
175,7
178,9
182,2
185,4
188,6
191,8
195,0
162,3
165,6
168,9
172,1
175,4
178,7
182,0
185,3
188,5
191,8
195,1
161,4
164,8
168,2
171,6
174,9
178,3
181,7
185,1
188,5
191,8
195,2
160,5
164,0
167,5
171,0
174,5
177,9
181,4
184,9
188,4
191,9
195,3
160,2
163,7
167,2
170,7
174,3
177,8
181,3
184,8
188,4
191,9
195,4
159,7
163,2
166,8
170,4
174,0
177,6
181,1
184,7
188,3
191,9
195,5
158,8
162,5
166,1
169,8
173,5
177,2
180,9
184,5
188,2
191,9
195,6
HFR
28,0
28,6
29,1
29,7
30,2
30,8
31,3
31,9
32,4
33,0
33,5
27,9
28,5
29,0
29,6
30,2
30,7
31,3
31,9
32,4
33,0
33,6
27,8
28,3
28,9
29,5
30,1
30,7
31,3
31,8
32,4
33,0
33,6
27,6
28,2
28,8
29,4
30,0
30,6
31,2
31,8
32,4
33,0
33,6
27,6
28,2
28,8
29,4
30,0
30,6
31,2
31,8
32,4
33,0
33,6
27,5
28,1
28,7
29,3
29,9
30,5
31,2
31,8
32,4
33,0
33,6
27,3
27,9
28,6
29,2
29,8
30,5
31,1
31,7
32,4
33,0
33,6
RCUE50WG2
HPD
35,2
36,5
37,8
39,2
40,6
42,0
43,4
44,8
46,3
47,8
49,3
35,0
36,3
37,6
39,0
40,4
41,9
43,3
44,8
46,3
47,8
49,3
34,6
36,0
37,4
38,8
40,2
41,7
43,2
44,7
46,2
47,8
49,4
34,2
35,6
37,1
38,5
40,0
41,5
43,1
44,6
46,2
47,8
49,4
34,1
35,5
37,0
38,4
39,9
41,5
43,0
44,6
46,2
47,8
49,5
33,9
35,3
36,8
38,3
39,8
41,4
42,9
44,5
46,2
47,8
49,5
33,5
35,0
36,5
38,0
39,6
41,2
42,8
44,5
46,1
47,8
49,6

Cooling Capacity (kW)
Condenser Heat Rejection (Kw)
IPT
25,0
25,2
25,3
25,5
25,7
25,9
26,0
26,2
26,4
26,6
26,8
26,9
27,1
27,2
27,4
27,5
27,7
27,9
28,0
28,2
28,4
28,5
30,1
30,2
30,4
30,5
30,6
30,8
30,9
31,1
31,2
31,3
31,5
33,3
33,4
33,5
33,6
33,7
33,8
34,0
34,1
34,2
34,3
34,4
34,5
34,7
34,8
34,9
35,0
35,1
35,2
35,3
35,4
35,5
35,6
36,5
36,6
36,6
36,7
36,8
36,9
37,0
37,1
37,2
37,3
37,4
39,7
39,7
39,8
39,8
39,9
40,0
40,0
40,1
40,2
40,2
40,3
CCAP
164,6
168,2
171,9
175,5
179,1
182,8
186,4
190,0
193,7
197,3
200,9
169,1
174,7
180,4
186,0
191,6
197,3
202,9
208,6
214,2
219,9
225,5
156,8
160,7
164,6
168,4
172,3
176,2
180,0
183,9
187,8
191,7
195,5
149,5
154,7
160,0
165,3
170,5
175,8
181,1
186,3
191,6
196,9
202,1
145,5
150,7
155,9
161,1
166,3
171,5
176,7
181,9
187,1
192,3
197,4
147,1
151,3
155,4
159,6
163,8
167,9
172,1
176,3
180,4
184,6
188,8
129,9
134,8
139,6
144,5
149,4
154,3
159,2
164,1
169,0
173,9
178,7
CFR
28,3
28,9
29,6
30,2
30,8
31,4
32,1
32,7
33,3
33,9
34,6
29,1
30,1
31,0
32,0
33,0
33,9
34,9
35,9
36,8
37,8
38,8
27,0
27,6
28,3
29,0
29,6
30,3
31,0
31,6
32,3
33,0
33,6
25,7
26,6
27,5
28,4
29,3
30,2
31,1
32,0
33,0
33,9
34,8
25,0
25,9
26,8
27,7
28,6
29,5
30,4
31,3
32,2
33,1
34,0
25,3
26,0
26,7
27,5
28,2
28,9
29,6
30,3
31,0
31,8
32,5
22,3
23,2
24,0
24,9
25,7
26,5
27,4
28,2
29,1
29,9
30,7
CPD
38,7
40,4
42,1
43,8
45,5
47,3
49,1
51,0
52,9
54,8
56,7
40,8
43,4
46,1
48,9
51,8
54,8
57,8
60,9
64,1
67,4
70,7
35,3
37,0
38,7
40,5
42,3
44,1
46,0
47,9
49,8
51,8
53,8
32,2
34,4
36,7
39,0
41,5
43,9
46,5
49,1
51,8
54,5
57,4
30,6
32,7
34,9
37,2
39,5
41,9
44,4
46,9
49,5
52,1
54,9
31,2
33,0
34,7
36,5
38,4
40,3
42,2
44,2
46,2
48,2
50,3
24,6
26,4
28,3
30,2
32,2
34,2
36,3
38,5
40,7
43,0
45,4
HCAP
194,4
198,3
202,1
206,0
209,8
213,6
217,5
221,3
225,2
229,0
232,9
201,2
207,0
212,9
218,7
224,5
230,4
236,2
242,1
247,9
253,7
259,6
192,7
196,8
200,8
204,8
208,9
212,9
217,0
221,0
225,0
229,1
233,1
189,2
194,6
200,0
205,4
210,8
216,2
221,6
227,0
232,4
237,8
243,2
186,8
192,1
197,4
202,7
208,1
213,4
218,7
224,0
229,3
234,6
239,9
190,6
194,9
199,2
203,5
207,7
212,0
216,3
220,6
224,8
229,1
233,4
177,2
182,2
187,1
192,1
197,1
202,0
207,0
212,0
216,9
221,9
226,9
HFR
33,4
34,1
34,8
35,4
36,1
36,7
37,4
38,1
38,7
39,4
40,1
34,6
35,6
36,6
37,6
38,6
39,6
40,6
41,6
42,6
43,6
44,6
33,2
33,8
34,5
35,2
35,9
36,6
37,3
38,0
38,7
39,4
40,1
32,5
33,5
34,4
35,3
36,3
37,2
38,1
39,0
40,0
40,9
41,8
32,1
33,0
34,0
34,9
35,8
36,7
37,6
38,5
39,4
40,4
41,3
32,8
33,5
34,3
35,0
35,7
36,5
37,2
37,9
38,7
39,4
40,1
30,5
31,3
32,2
33,0
33,9
34,8
35,6
36,5
37,3
38,2
39,0
RCUE60WG2
HPD
35,4
36,7
38,1
39,5
40,9
42,3
43,7
45,2
46,7
48,2
49,7
37,8
39,8
42,0
44,2
46,4
48,7
51,1
53,5
55,9
58,4
61,0
34,8
36,2
37,6
39,1
40,5
42,0
43,5
45,0
46,6
48,2
49,8
33,6
35,5
37,3
39,3
41,2
43,2
45,3
47,4
49,5
51,7
53,9
32,8
34,6
36,4
38,3
40,2
42,2
44,2
46,2
48,3
50,4
52,6
34,1
35,6
37,1
38,6
40,1
41,7
43,3
44,9
46,5
48,2
49,9
29,7
31,3
32,9
34,6
36,3
38,1
39,8
41,7
43,5
45,4
47,3
HFR: Condenser Water Flow Rate at 5C (m3/h)

HPD:Condenser Water Pressure Drop (kPa)
CFR:Chilled Water Flow Rate at 5C (m3/h)
CPD:
Water Cooler Pressure Drop (kPa)
IPT:
Compressor Input Power (kW)
IPT
29,8
30,0
30,2
30,5
30,7
30,9
31,1
31,3
31,5
31,7
32,0
32,1
32,3
32,5
32,7
32,9
33,1
33,3
33,5
33,7
33,9
34,1
35,9
36,1
36,2
36,4
36,6
36,7
36,9
37,1
37,2
37,4
37,6
39,7
39,9
40,0
40,1
40,3
40,4
40,5
40,7
40,8
41,0
41,1
41,2
41,4
41,5
41,6
41,8
41,9
42,0
42,1
42,3
42,4
42,5
43,5
43,6
43,8
43,9
44,0
44,1
44,2
44,3
44,4
44,5
44,6
47,3
47,4
47,5
47,6
47,7
47,7
47,8
47,9
48,0
48,1
48,1
CCAP
199,6
204,0
208,4
212,8
217,2
221,6
226,0
230,4
234,8
239,2
243,6
205,0
211,8
218,7
225,5
232,4
239,2
246,1
252,9
259,7
266,6
273,4
190,1
194,8
199,5
204,2
208,9
213,6
218,3
223,0
227,7
232,4
237,1
181,2
187,6
194,0
200,4
206,8
213,2
219,5
225,9
232,3
238,7
245,1
176,5
182,8
189,1
195,4
201,6
207,9
214,2
220,5
226,8
233,1
239,4
178,4
183,4
188,5
193,5
198,6
203,6
208,7
213,7
218,8
223,8
228,9
157,5
163,4
169,3
175,2
181,2
187,1
193,0
198,9
204,9
210,8
216,7
CFR
34,3
35,1
35,8
36,6
37,4
38,1
38,9
39,6
40,4
41,1
41,9
35,3
36,4
37,6
38,8
40,0
41,1
42,3
43,5
44,7
45,9
47,0
32,7
33,5
34,3
35,1
35,9
36,7
37,5
38,4
39,2
40,0
40,8
31,2
32,3
33,4
34,5
35,6
36,7
37,8
38,9
40,0
41,1
42,2
30,4
31,4
32,5
33,6
34,7
35,8
36,8
37,9
39,0
40,1
41,2
30,7
31,5
32,4
33,3
34,2
35,0
35,9
36,8
37,6
38,5
39,4
27,1
28,1
29,1
30,1
31,2
32,2
33,2
34,2
35,2
36,3
37,3
CPD
37,8
39,4
41,0
42,7
44,4
46,1
47,9
49,7
51,5
53,4
55,3
39,8
42,3
45,0
47,7
50,5
53,4
56,4
59,4
62,5
65,7
68,9
34,4
36,1
37,7
39,5
41,2
43,0
44,8
46,7
48,6
50,5
52,5
31,4
33,6
35,8
38,1
40,4
42,8
45,3
47,9
50,5
53,2
55,9
29,8
31,9
34,1
36,3
38,5
40,8
43,2
45,7
48,2
50,8
53,5
30,5
32,1
33,8
35,6
37,4
39,2
41,1
43,1
45,0
47,0
49,1
24,0
25,8
27,6
29,4
31,4
33,4
35,4
37,5
39,7
41,9
44,2
HCAP
HFR
236,2
240,8
245,5
250,2
254,8
259,5
264,2
268,8
273,5
278,2
282,8
244,4
251,5
258,6
265,7
272,7
279,8
286,9
294,0
301,1
308,2
315,2
234,2
239,1
244,0
248,9
253,8
258,7
263,6
268,5
273,4
278,3
283,2
230,0
236,5
243,1
249,7
256,2
262,8
269,3
275,9
282,4
289,0
295,5
227,1
233,6
240,0
246,5
252,9
259,3
265,8
272,2
278,7
285,1
291,6
231,8
237,0
242,2
247,4
252,5
257,7
262,9
268,1
273,3
278,5
283,7
215,6
221,6
227,6
233,6
239,7
245,7
251,7
257,7
263,8
269,8
275,8
Conversion Multiplier:
1 kW = 860 kcal/h
= 3412 Btu/h
1 kPa = 0.102 mAq
40,6
41,4
42,2
43,0
43,8
44,6
45,4
46,2
47,0
47,8
48,6
42,0
43,3
44,5
45,7
46,9
48,1
49,3
50,6
51,8
53,0
54,2
40,3
41,1
42,0
42,8
43,7
44,5
45,3
46,2
47,0
47,9
48,7
39,6
40,7
41,8
42,9
44,1
45,2
46,3
47,4
48,6
49,7
50,8
39,1
40,2
41,3
42,4
43,5
44,6
45,7
46,8
47,9
49,0
50,2
39,9
40,8
41,7
42,5
43,4
44,3
45,2
46,1
47,0
47,9
48,8
37,1
38,1
39,2
40,2
41,2
42,3
43,3
44,3
45,4
46,4
47,4
HPD
37,0
38,4
39,8
41,2
42,7
44,2
45,7
47,3
48,8
50,4
52,0
39,5
41,7
43,9
46,2
48,6
51,0
53,5
56,0
58,6
61,2
63,9
36,4
37,9
39,3
40,8
42,4
44,0
45,5
47,2
48,8
50,5
52,2
35,2
37,1
39,1
41,1
43,1
45,3
47,4
49,6
51,9
54,2
56,6
34,3
36,2
38,1
40,1
42,1
44,2
46,3
48,4
50,6
52,9
55,1
35,7
37,2
38,8
40,4
42,0
43,6
45,3
47,0
48,8
50,5
52,3
31,1
32,8
34,5
36,2
38,0
39,8
41,7
43,6
45,6
47,6
49,6
IPT
36,6
36,9
37,1
37,4
37,7
37,9
38,2
38,4
38,7
39,0
39,2
39,4
39,7
39,9
40,1
40,4
40,6
40,9
41,1
41,3
41,6
41,8
44,1
44,3
44,5
44,7
44,9
45,1
45,3
45,5
45,7
45,9
46,1
48,8
48,9
49,1
49,3
49,4
49,6
49,8
49,9
50,1
50,3
50,4
50,6
50,8
50,9
51,1
51,3
51,4
51,6
51,7
51,9
52,0
52,2
53,4
53,6
53,7
53,8
54,0
54,1
54,2
54,4
54,5
54,6
54,8
58,1
58,2
58,3
58,4
58,5
58,6
58,7
58,8
58,9
59,0
59,1

Performance Table (cont.)
RCUE80WG2
CDOT
22,0
25,0
30,0
35,0
37,0
40,0
45,0
CLOT
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
Where,
CDOT:
CLOT:
CCAP:
HCAP:
CCAP
238,7
243,9
249,2
254,5
259,7
265,0
270,3
275,5
280,8
286,1
291,3
234,4
239,8
245,2
250,6
256,0
261,4
266,8
272,2
277,6
283,0
288,4
227,4
233,0
238,6
244,2
249,8
255,5
261,1
266,7
272,3
277,9
283,5
220,3
226,2
232,0
237,8
243,7
249,5
255,3
261,1
267,0
272,8
278,6
217,5
223,4
229,4
235,3
241,2
247,1
253,0
258,9
264,8
270,8
276,7
213,3
219,3
225,4
231,4
237,5
243,5
249,6
255,6
261,6
267,7
273,7
206,2
212,5
218,8
225,0
231,3
237,5
243,8
250,1
256,3
262,6
268,8
CFR
41,1
42,0
42,9
43,8
44,7
45,6
46,5
47,4
48,3
49,2
50,1
40,3
41,3
42,2
43,1
44,0
45,0
45,9
46,8
47,7
48,7
49,6
39,1
40,1
41,0
42,0
43,0
43,9
44,9
45,9
46,8
47,8
48,8
37,9
38,9
39,9
40,9
41,9
42,9
43,9
44,9
45,9
46,9
47,9
37,4
38,4
39,4
40,5
41,5
42,5
43,5
44,5
45,6
46,6
47,6
36,7
37,7
38,8
39,8
40,8
41,9
42,9
44,0
45,0
46,0
47,1
35,5
36,6
37,6
38,7
39,8
40,9
41,9
43,0
44,1
45,2
46,2
CPD
45,5
47,4
49,4
51,4
53,5
55,6
57,7
59,9
62,1
64,3
66,6
44,0
45,9
47,9
50,0
52,0
54,2
56,3
58,5
60,8
63,0
65,3
41,5
43,5
45,5
47,6
49,7
51,8
54,0
56,3
58,5
60,9
63,2
39,1
41,1
43,1
45,2
47,3
49,5
51,8
54,0
56,4
58,8
61,2
38,1
40,1
42,2
44,3
46,4
48,6
50,9
53,2
55,5
57,9
60,4
36,7
38,7
40,8
42,9
45,1
47,3
49,6
51,9
54,2
56,7
59,1
34,4
36,4
38,5
40,7
42,8
45,1
47,4
49,7
52,2
54,6
57,1
HCAP
279,3
284,9
290,4
296,0
301,5
307,1
312,6
318,2
323,8
329,3
334,9
278,2
283,8
289,5
295,2
300,8
306,5
312,2
317,8
323,5
329,2
334,8
276,3
282,2
288,0
293,8
299,7
305,5
311,4
317,2
323,0
328,9
334,7
274,5
280,5
286,5
292,5
298,5
304,5
310,6
316,6
322,6
328,6
334,6
273,7
279,8
285,9
292,0
298,1
304,2
310,2
316,3
322,4
328,5
334,6
272,6
278,8
285,0
291,2
297,4
303,6
309,8
315,9
322,1
328,3
334,5
270,8
277,1
283,5
289,9
296,2
302,6
309,0
315,3
321,7
328,1
334,4
HFR
48,0
49,0
50,0
50,9
51,9
52,8
53,8
54,7
55,7
56,6
57,6
47,8
48,8
49,8
50,8
51,7
52,7
53,7
54,7
55,6
56,6
57,6
47,5
48,5
49,5
50,5
51,5
52,5
53,6
54,6
55,6
56,6
57,6
47,2
48,2
49,3
50,3
51,3
52,4
53,4
54,5
55,5
56,5
57,6
47,1
48,1
49,2
50,2
51,3
52,3
53,4
54,4
55,5
56,5
57,5
46,9
48,0
49,0
50,1
51,1
52,2
53,3
54,3
55,4
56,5
57,5
46,6
47,7
48,8
49,9
51,0
52,0
53,1
54,2
55,3
56,4
57,5
RCUE100WG2
HPD
58,8
61,1
63,4
65,7
68,1
70,5
73,0
75,5
78,0
80,6
83,2
58,4
60,7
63,0
65,4
67,8
70,3
72,8
75,3
77,9
80,5
83,2
57,6
60,0
62,4
64,8
67,3
69,8
72,4
75,0
77,7
80,4
83,2
56,9
59,3
61,8
64,3
66,8
69,4
72,1
74,8
77,5
80,3
83,1
56,6
59,0
61,5
64,0
66,6
69,2
71,9
74,6
77,4
80,2
83,1
56,2
58,6
61,1
63,7
66,3
69,0
71,7
74,5
77,3
80,2
83,1
55,4
58,0
60,5
63,2
65,8
68,6
71,4
74,2
77,1
80,0
83,0

IPT
40,6
40,9
41,2
41,5
41,8
42,1
42,4
42,7
43,0
43,2
43,5
43,7
44,0
44,3
44,5
44,8
45,1
45,3
45,6
45,9
46,1
46,4
48,9
49,2
49,4
49,6
49,8
50,1
50,3
50,5
50,8
51,0
51,2
54,1
54,3
54,5
54,7
54,9
55,1
55,2
55,4
55,6
55,8
56,0
56,2
56,4
56,5
56,7
56,9
57,1
57,2
57,4
57,6
57,7
57,9
59,3
59,5
59,6
59,8
59,9
60,1
60,2
60,3
60,5
60,6
60,8
64,5
64,6
64,7
64,8
64,9
65,0
65,2
65,3
65,4
65,5
65,6
CCAP
329,2
336,5
343,7
351,0
358,3
365,5
372,8
380,0
387,3
394,6
401,8
323,4
330,8
338,3
345,7
353,1
360,6
368,0
375,5
382,9
390,3
397,8
313,6
321,4
329,1
336,9
344,6
352,3
360,1
367,8
375,6
383,3
391,0
303,9
312,0
320,0
328,0
336,1
344,1
352,2
360,2
368,2
376,3
384,3
300,0
308,2
316,3
324,5
332,7
340,8
349,0
357,1
365,3
373,4
381,6
294,2
302,5
310,9
319,2
327,5
335,9
344,2
352,6
360,9
369,2
377,6
284,5
293,1
301,7
310,4
319,0
327,6
336,3
344,9
353,5
362,2
370,8
CFR
56,6
57,9
59,1
60,4
61,6
62,9
64,1
65,4
66,6
67,9
69,1
55,6
56,9
58,2
59,5
60,7
62,0
63,3
64,6
65,9
67,1
68,4
53,9
55,3
56,6
57,9
59,3
60,6
61,9
63,3
64,6
65,9
67,3
52,3
53,7
55,0
56,4
57,8
59,2
60,6
62,0
63,3
64,7
66,1
51,6
53,0
54,4
55,8
57,2
58,6
60,0
61,4
62,8
64,2
65,6
50,6
52,0
53,5
54,9
56,3
57,8
59,2
60,6
62,1
63,5
64,9
48,9
50,4
51,9
53,4
54,9
56,4
57,8
59,3
60,8
62,3
63,8
CPD
39,8
41,5
43,2
44,9
46,7
48,5
50,4
52,3
54,2
56,1
58,1
38,5
40,2
41,9
43,7
45,5
47,3
49,2
51,1
53,0
55,0
57,0
36,3
38,0
39,8
41,6
43,4
45,3
47,2
49,1
51,1
53,1
55,2
34,2
35,9
37,7
39,5
41,4
43,3
45,2
47,2
49,2
51,3
53,4
33,4
35,1
36,9
38,7
40,6
42,5
44,4
46,4
48,5
50,5
52,7
32,1
33,9
35,7
37,5
39,4
41,3
43,3
45,3
47,4
49,5
51,6
30,2
31,9
33,7
35,6
37,5
39,4
41,4
43,5
45,6
47,7
49,9
HCAP
388,8
396,5
404,2
411,9
419,6
427,3
435,0
442,7
450,4
458,1
465,8
387,6
395,4
403,2
411,1
418,9
426,8
434,6
442,4
450,3
458,1
465,9
385,5
393,5
401,6
409,7
417,8
425,8
433,9
442,0
450,1
458,1
466,2
383,4
391,7
400,0
408,3
416,6
424,9
433,3
441,6
449,9
458,2
466,5
382,5
390,9
399,4
407,8
416,2
424,6
433,0
441,4
449,8
458,2
466,6
381,3
389,8
398,4
406,9
415,5
424,0
432,6
441,1
449,7
458,2
466,8
379,2
388,0
396,8
405,5
414,3
423,1
431,9
440,7
449,5
458,3
467,1
HFR
66,9
68,2
69,5
70,8
72,2
73,5
74,8
76,1
77,5
78,8
80,1
66,7
68,0
69,4
70,7
72,1
73,4
74,7
76,1
77,4
78,8
80,1
66,3
67,7
69,1
70,5
71,9
73,2
74,6
76,0
77,4
78,8
80,2
65,9
67,4
68,8
70,2
71,7
73,1
74,5
75,9
77,4
78,8
80,2
65,8
67,2
68,7
70,1
71,6
73,0
74,5
75,9
77,4
78,8
80,3
65,6
67,0
68,5
70,0
71,5
72,9
74,4
75,9
77,3
78,8
80,3
65,2
66,7
68,2
69,8
71,3
72,8
74,3
75,8
77,3
78,8
80,3
RCUE120WG2
HPD
64,2
66,6
69,1
71,6
74,2
76,8
79,4
82,1
84,8
87,6
90,4
63,8
66,3
68,8
71,3
73,9
76,6
79,3
82,0
84,8
87,6
90,4
63,2
65,7
68,3
70,9
73,6
76,3
79,0
81,8
84,7
87,6
90,5
62,5
65,1
67,8
70,4
73,2
76,0
78,8
81,7
84,6
87,6
90,6
62,3
64,9
67,5
70,3
73,0
75,8
78,7
81,6
84,6
87,6
90,7
61,9
64,5
67,2
70,0
72,8
75,7
78,6
81,5
84,6
87,6
90,8
61,2
63,9
66,7
69,5
72,4
75,4
78,3
81,4
84,5
87,7
90,9

CPD:
IPT:
IPT
59,6
60,1
60,5
60,9
61,3
61,8
62,2
62,6
63,1
63,5
63,9
64,2
64,6
65,0
65,4
65,8
66,2
66,6
67,0
67,3
67,7
68,1
71,8
72,2
72,5
72,8
73,2
73,5
73,8
74,2
74,5
74,8
75,2
79,5
79,7
80,0
80,3
80,5
80,8
81,1
81,4
81,6
81,9
82,2
82,5
82,7
83,0
83,3
83,5
83,8
84,0
84,3
84,5
84,8
85,0
87,1
87,3
87,5
87,7
87,9
88,2
88,4
88,6
88,8
89,0
89,2
94,7
94,8
95,0
95,2
95,3
95,5
95,6
95,8
95,9
96,1
96,3
CCAP
399,2
408,0
416,8
425,6
434,4
443,2
452,0
460,8
469,6
478,4
487,2
392,1
401,1
410,1
419,2
428,2
437,2
446,2
455,3
464,3
473,3
482,3
380,3
389,7
399,1
408,4
417,8
427,2
436,6
446,0
455,4
464,8
474,1
368,5
378,3
388,0
397,7
407,5
417,2
427,0
436,7
446,5
456,2
466,0
363,8
373,7
383,6
393,5
403,4
413,2
423,1
433,0
442,9
452,8
462,7
356,7
366,8
376,9
387,0
397,1
407,3
417,4
427,5
437,6
447,7
457,8
344,9
355,4
365,9
376,3
386,8
397,3
407,7
418,2
428,7
439,1
449,6
CFR
68,7
70,2
71,7
73,2
74,7
76,2
77,7
79,3
80,8
82,3
83,8
67,4
69,0
70,5
72,1
73,6
75,2
76,8
78,3
79,9
81,4
83,0
65,4
67,0
68,6
70,3
71,9
73,5
75,1
76,7
78,3
79,9
81,6
63,4
65,1
66,7
68,4
70,1
71,8
73,4
75,1
76,8
78,5
80,1
62,6
64,3
66,0
67,7
69,4
71,1
72,8
74,5
76,2
77,9
79,6
61,4
63,1
64,8
66,6
68,3
70,0
71,8
73,5
75,3
77,0
78,7
59,3
61,1
62,9
64,7
66,5
68,3
70,1
71,9
73,7
75,5
77,3
CPD
57,3
59,8
62,2
64,8
67,3
69,9
72,6
75,3
78,1
80,9
83,7
55,4
57,9
60,4
62,9
65,5
68,2
70,9
73,6
76,4
79,2
82,1
52,3
54,8
57,3
59,9
62,5
65,2
68,0
70,8
73,6
76,5
79,5
49,3
51,8
54,3
57,0
59,6
62,4
65,2
68,0
70,9
73,9
76,9
48,1
50,6
53,2
55,8
58,5
61,2
64,1
66,9
69,9
72,8
75,9
46,3
48,9
51,4
54,1
56,8
59,6
62,4
65,3
68,3
71,3
74,4
43,5
46,0
48,6
51,3
54,0
56,8
59,7
62,7
65,7
68,7
71,9
HCAP
HFR
472,4
481,7
491,0
500,4
509,7
519,0
528,4
537,7
547,0
556,4
565,7
470,9
480,4
489,9
499,4
508,9
518,4
527,9
537,4
546,9
556,5
566,0
468,5
478,3
488,1
497,9
507,6
517,4
527,2
537,0
546,8
556,6
566,4
466,0
476,1
486,2
496,3
506,4
516,4
526,5
536,6
546,7
556,8
566,9
465,1
475,3
485,5
495,7
505,9
516,1
526,3
536,5
546,7
556,8
567,0
463,6
474,0
484,3
494,7
505,1
515,5
525,8
536,2
546,6
556,9
567,3
461,2
471,8
482,5
493,1
503,8
514,5
525,1
535,8
546,5
557,1
567,8
1 kW = 860 kcal/h
= 3412 Btu/h
1 kPa = 0.102 mAq
81,2
82,9
84,5
86,1
87,7
89,3
90,9
92,5
94,1
95,7
97,3
81,0
82,6
84,3
85,9
87,5
89,2
90,8
92,4
94,1
95,7
97,3
80,6
82,3
83,9
85,6
87,3
89,0
90,7
92,4
94,1
95,7
97,4
80,2
81,9
83,6
85,4
87,1
88,8
90,6
92,3
94,0
95,8
97,5
80,0
81,7
83,5
85,3
87,0
88,8
90,5
92,3
94,0
95,8
97,5
79,7
81,5
83,3
85,1
86,9
88,7
90,4
92,2
94,0
95,8
97,6
79,3
81,2
83,0
84,8
86,7
88,5
90,3
92,2
94,0
95,8
97,7
HPD
68,3
70,9
73,6
76,2
79,0
81,7
84,6
87,4
90,3
93,3
96,3
67,9
70,6
73,2
76,0
78,7
81,6
84,4
87,3
90,3
93,3
96,4
67,3
70,0
72,7
75,5
78,4
81,3
84,2
87,2
90,3
93,4
96,5
66,6
69,4
72,2
75,1
78,0
81,0
84,0
87,1
90,2
93,4
96,7
66,3
69,1
72,0
74,9
77,8
80,9
83,9
87,0
90,2
93,4
96,7
65,9
68,8
71,7
74,6
77,6
80,7
83,8
87,0
90,2
93,5
96,8
65,3
68,2
71,1
74,2
77,2
80,4
83,6
86,8
90,1
93,5
97,0
IPT
73,2
73,7
74,3
74,8
75,3
75,8
76,4
76,9
77,4
77,9
78,5
78,8
79,3
79,8
80,3
80,7
81,2
81,7
82,2
82,7
83,2
83,6
88,2
88,6
89,0
89,4
89,8
90,2
90,6
91,0
91,4
91,9
92,3
97,5
97,9
98,2
98,5
98,9
99,2
99,5
99,9
100,2
100,6
100,9
101,3
101,6
101,9
102,2
102,5
102,8
103,1
103,4
103,7
104,0
104,4
106,9
107,1
107,4
107,7
107,9
108,2
108,5
108,7
109,0
109,3
109,5
116,2
116,4
116,6
116,8
117,0
117,2
117,4
117,6
117,8
118,0
118,2

Performance Table (R407C) (cont.)
RCUE 150 WG2
CDOT
22,0
25,0
30,0
35,0
37,0
40,0
45,0
Where,
CDOT:
CLOT:
CCAP:
HCAP:
CLOT
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
CCAP
457,8
467,9
478,0
488,1
498,2
508,3
518,4
528,5
538,6
548,7
558,8
449,7
460,0
470,4
480,7
491,1
501,4
511,8
522,1
532,5
542,8
553,2
436,2
446,9
457,7
468,5
479,2
490,0
500,7
511,5
522,3
533,0
543,8
422,6
433,8
445,0
456,2
467,4
478,5
489,7
500,9
512,1
523,2
534,4
417,2
428,6
439,9
451,3
462,6
474,0
485,3
496,6
508,0
519,3
530,7
409,1
420,7
432,3
443,9
455,5
467,1
478,7
490,3
501,9
513,5
525,0
395,6
407,6
419,6
431,6
443,6
455,6
467,6
479,6
491,7
503,7
515,7
CFR
78,7
80,5
82,2
84,0
85,7
87,4
89,2
90,9
92,6
94,4
96,1
77,3
79,1
80,9
82,7
84,5
86,2
88,0
89,8
91,6
93,4
95,1
75,0
76,9
78,7
80,6
82,4
84,3
86,1
88,0
89,8
91,7
93,5
72,7
74,6
76,5
78,5
80,4
82,3
84,2
86,2
88,1
90,0
91,9
71,8
73,7
75,7
77,6
79,6
81,5
83,5
85,4
87,4
89,3
91,3
70,4
72,4
74,4
76,4
78,3
80,3
82,3
84,3
86,3
88,3
90,3
68,0
70,1
72,2
74,2
76,3
78,4
80,4
82,5
84,6
86,6
88,7
RCUE 180 WG2
CPD
HCAP
HFR
HPD
IPT
CCAP
CFR
74,4
77,5
80,7
84,0
87,3
90,7
94,2
97,7
101,2
104,9
108,6
71,9
75,1
78,3
81,6
85,0
88,4
91,9
95,5
99,1
102,8
106,5
67,9
71,1
74,3
77,7
81,1
84,6
88,2
91,8
95,5
99,3
103,1
63,9
67,2
70,5
73,9
77,4
80,9
84,5
88,2
92,0
95,8
99,8
62,4
65,6
69,0
72,4
75,9
79,4
83,1
86,8
90,6
94,5
98,4
60,1
63,4
66,7
70,2
73,7
77,3
80,9
84,7
88,5
92,5
96,5
56,4
59,7
63,1
66,5
70,1
73,7
77,4
81,3
85,2
89,1
93,2
535,7
546,4
557,0
567,7
578,3
589,0
599,7
610,3
621,0
631,6
642,3
533,6
544,4
555,3
566,1
577,0
587,9
598,7
609,6
620,5
631,3
642,2
530,0
541,2
552,4
563,6
574,8
586,0
597,2
608,4
619,6
630,8
642,0
526,4
538,0
549,5
561,0
572,6
584,1
595,6
607,2
618,7
630,3
641,8
525,0
536,7
548,3
560,0
571,7
583,4
595,0
606,7
618,4
630,0
641,7
522,9
534,7
546,6
558,5
570,4
582,2
594,1
606,0
617,9
629,7
641,6
519,3
531,5
543,7
555,9
568,1
580,4
592,6
604,8
617,0
629,2
641,4
92,1
94,0
95,8
97,6
99,5
101,3
103,1
105,0
106,8
108,6
110,5
91,8
93,6
95,5
97,4
99,2
101,1
103,0
104,8
106,7
108,6
110,5
91,2
93,1
95,0
96,9
98,9
100,8
102,7
104,6
106,6
108,5
110,4
90,5
92,5
94,5
96,5
98,5
100,5
102,5
104,4
106,4
108,4
110,4
90,3
92,3
94,3
96,3
98,3
100,3
102,3
104,4
106,4
108,4
110,4
89,9
92,0
94,0
96,1
98,1
100,1
102,2
104,2
106,3
108,3
110,4
89,3
91,4
93,5
95,6
97,7
99,8
101,9
104,0
106,1
108,2
110,3
86,8
90,1
93,5
96,9
100,4
104,0
107,6
111,2
114,9
118,7
122,6
86,1
89,5
92,9
96,4
100,0
103,6
107,2
111,0
114,8
118,6
122,5
85,1
88,5
92,0
95,6
99,2
102,9
106,7
110,6
114,5
118,4
122,5
84,0
87,5
91,1
94,8
98,5
102,3
106,2
110,1
114,2
118,2
122,4
83,5
87,1
90,7
94,4
98,2
102,1
106,0
110,0
114,0
118,2
122,4
82,9
86,5
90,2
94,0
97,8
101,7
105,7
109,7
113,8
118,0
122,3
81,8
85,5
89,3
93,1
97,1
101,1
105,2
109,3
113,5
117,9
122,2
77,9
78,5
79,0
79,6
80,1
80,7
81,3
81,8
82,4
82,9
83,5
83,9
84,4
84,9
85,4
85,9
86,4
86,9
87,5
88,0
88,5
89,0
93,8
94,3
94,7
95,1
95,6
96,0
96,4
96,9
97,3
97,7
98,2
103,8
104,1
104,5
104,9
105,2
105,6
105,9
106,3
106,7
107,0
107,4
107,8
108,1
108,4
108,7
109,1
109,4
109,7
110,1
110,4
110,7
111,0
113,7
114,0
114,3
114,6
114,9
115,1
115,4
115,7
116,0
116,3
116,6
123,7
123,9
124,1
124,3
124,5
124,7
124,9
125,1
125,3
125,5
125,7
540,1
552,0
563,9
575,8
587,8
599,7
611,6
623,5
635,4
647,3
659,3
530,5
542,7
554,9
567,2
579,4
591,6
603,8
616,0
628,2
640,4
652,6
514,6
527,3
540,0
552,7
565,4
578,1
590,8
603,5
616,2
628,9
641,6
498,6
511,8
525,0
538,2
551,4
564,6
577,7
590,9
604,1
617,3
630,5
492,2
505,6
519,0
532,4
545,8
559,2
572,5
585,9
599,3
612,7
626,1
458,3
474,9
491,6
508,2
524,9
541,6
558,2
574,9
591,5
608,2
624,8
466,7
480,9
495,1
509,2
523,4
537,5
551,7
565,9
580,0
594,2
608,4
92,9
94,9
97,0
99,0
101,1
103,1
105,2
107,2
109,3
111,3
113,4
91,2
93,3
95,5
97,6
99,7
101,8
103,9
106,0
108,1
110,2
112,3
88,5
90,7
92,9
95,1
97,2
99,4
101,6
103,8
106,0
108,2
110,3
85,8
88,0
90,3
92,6
94,8
97,1
99,4
101,6
103,9
106,2
108,4
84,7
87,0
89,3
91,6
93,9
96,2
98,5
100,8
103,1
105,4
107,7
78,8
81,7
84,6
87,4
90,3
93,1
96,0
98,9
101,7
104,6
107,5
80,3
82,7
85,1
87,6
90,0
92,5
94,9
97,3
99,8
102,2
104,6

CPD
31,0
32,3
33,7
35,1
36,5
37,9
39,3
40,8
42,3
43,8
45,4
30,0
31,3
32,7
34,0
35,5
36,9
38,4
39,9
41,4
43,0
44,5
28,3
29,6
31,0
32,4
33,8
35,3
36,8
38,3
39,9
41,5
43,1
26,6
28,0
29,4
30,8
32,3
33,8
35,3
36,8
38,4
40,0
41,7
26,0
27,3
28,7
30,2
31,6
33,1
34,7
36,2
37,8
39,5
41,1
22,6
24,3
25,9
27,6
29,4
31,2
33,0
34,9
36,9
38,9
41,0
23,5
24,8
26,3
27,7
29,2
30,7
32,3
33,9
35,5
37,2
38,9

CPD:
IPT:
HCAP
HFR
632,2
644,7
657,3
669,9
682,5
695,0
707,6
720,2
732,8
745,4
757,9
629,6
642,5
655,3
668,1
680,9
693,7
706,5
719,4
732,2
745,0
757,8
625,5
638,7
651,9
665,1
678,3
691,5
704,7
718,0
731,2
744,4
757,6
621,3
634,9
648,5
662,1
675,7
689,3
702,9
716,6
730,2
743,8
757,4
619,6
633,4
647,1
660,9
674,7
688,5
702,2
716,0
729,8
743,5
757,3
592,7
609,7
626,7
643,7
660,7
677,6
694,6
711,6
728,6
745,6
762,6
612,9
627,3
641,7
656,1
670,5
684,9
699,3
713,8
728,2
742,6
757,0
108,7
110,9
113,1
115,2
117,4
119,5
121,7
123,9
126,0
128,2
130,4
108,3
110,5
112,7
114,9
117,1
119,3
121,5
123,7
125,9
128,1
130,3
107,6
109,9
112,1
114,4
116,7
118,9
121,2
123,5
125,8
128,0
130,3
106,9
109,2
111,5
113,9
116,2
118,6
120,9
123,2
125,6
127,9
130,3
106,6
108,9
111,3
113,7
116,0
118,4
120,8
123,2
125,5
127,9
130,3
101,9
104,9
107,8
110,7
113,6
116,6
119,5
122,4
125,3
128,2
131,2
105,4
107,9
110,4
112,9
115,3
117,8
120,3
122,8
125,2
127,7
130,2
HPD
29,8
30,9
32,1
33,2
34,4
35,6
36,9
38,1
39,4
40,7
42,0
29,6
30,7
31,9
33,1
34,3
35,5
36,8
38,1
39,3
40,7
42,0
29,2
30,4
31,6
32,8
34,0
35,3
36,6
37,9
39,2
40,6
42,0
28,8
30,0
31,3
32,5
33,8
35,1
36,4
37,8
39,1
40,5
42,0
28,7
29,9
31,1
32,4
33,7
35,0
36,3
37,7
39,1
40,5
41,9
26,4
27,8
29,3
30,8
32,4
34,0
35,6
37,3
39,0
40,7
42,5
28,1
29,3
30,6
32,0
33,3
34,7
36,1
37,5
38,9
40,4
41,9
IPT
92,1
92,7
93,4
94,0
94,7
95,4
96,0
96,7
97,3
98,0
98,7
99,1
99,7
100,3
100,9
101,5
102,2
102,8
103,4
104,0
104,6
105,2
110,9
111,4
111,9
112,4
112,9
113,5
114,0
114,5
115,0
115,5
116,0
122,7
123,1
123,5
123,9
124,3
124,8
125,2
125,6
126,0
126,5
126,9
127,4
127,7
128,1
128,5
128,9
129,3
129,7
130,1
130,5
130,8
131,2
134,4
134,7
135,1
135,4
135,7
136,1
136,4
136,7
137,1
137,4
137,7
146,2
146,4
146,7
146,9
147,1
147,4
147,6
147,9
148,1
148,4
148,6
1 kW = 860 kcal/h
= 3412 Btu/h
1 kPa = 0.102 mAq

Performance Table (cont.)
RCUE 200 WG2
CDOT
22,0
25,0
30,0
35,0
37,0
40,0
45,0
Where,
CDOT:
CLOT:
CCAP:
HCAP:
CLOT
CCAP
CFR
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
617,2
630,9
644,5
658,1
671,7
685,3
699,0
712,6
726,2
739,8
753,4
606,3
620,3
634,2
648,2
662,1
676,1
690,0
704,0
718,0
731,9
745,9
588,1
602,6
617,1
631,6
646,1
660,6
675,2
689,7
704,2
718,7
733,2
569,9
584,9
600,0
615,1
630,1
645,2
660,3
675,4
690,4
705,5
720,6
562,6
577,9
593,2
608,5
623,7
639,0
654,3
669,6
684,9
700,2
715,5
551,6
567,3
582,9
598,5
614,1
629,8
645,4
661,0
676,7
692,3
707,9
533,4
549,6
565,8
582,0
598,2
614,3
630,5
646,7
662,9
679,1
695,3
106,2
108,5
110,9
113,2
115,5
117,9
120,2
122,6
124,9
127,3
129,6
104,3
106,7
109,1
111,5
113,9
116,3
118,7
121,1
123,5
125,9
128,3
101,2
103,6
106,1
108,6
111,1
113,6
116,1
118,6
121,1
123,6
126,1
98,0
100,6
103,2
105,8
108,4
111,0
113,6
116,2
118,8
121,3
123,9
96,8
99,4
102,0
104,7
107,3
109,9
112,5
115,2
117,8
120,4
123,1
94,9
97,6
100,3
102,9
105,6
108,3
111,0
113,7
116,4
119,1
121,8
91,7
94,5
97,3
100,1
102,9
105,7
108,5
111,2
114,0
116,8
119,6
CPD
40,0
41,7
43,5
45,2
47,1
48,9
50,8
52,7
54,6
56,6
58,6
38,7
40,4
42,2
44,0
45,8
47,6
49,5
51,5
53,4
55,4
57,5
36,5
38,2
40,0
41,8
43,7
45,6
47,5
49,5
51,5
53,6
55,6
34,4
36,1
37,9
39,8
41,6
43,6
45,5
47,5
49,6
51,7
53,8
33,5
35,3
37,1
38,9
40,8
42,8
44,8
46,8
48,8
50,9
53,1
32,3
34,1
35,9
37,7
39,6
41,6
43,6
45,6
47,7
49,9
52,0
30,3
32,1
33,9
35,8
37,7
39,7
41,7
43,8
45,9
48,0
50,3

HCAP
HFR
728,0
742,4
756,8
771,2
785,6
800,0
814,4
828,8
843,3
857,7
872,1
725,5
740,2
754,9
769,6
784,2
798,9
813,6
828,3
843,0
857,6
872,3
721,4
736,6
751,7
766,8
781,9
797,1
812,2
827,3
842,5
857,6
872,7
717,3
732,9
748,5
764,1
779,7
795,2
810,8
826,4
842,0
857,6
873,1
715,7
731,5
747,2
763,0
778,7
794,5
810,3
826,0
841,8
857,6
873,3
713,3
729,3
745,3
761,3
777,4
793,4
809,4
825,5
841,5
857,5
873,6
709,2
725,7
742,1
758,6
775,1
791,6
808,0
824,5
841,0
857,5
874,0
125,2
127,7
130,2
132,6
135,1
137,6
140,1
142,6
145,0
147,5
150,0
124,8
127,3
129,8
132,4
134,9
137,4
139,9
142,5
145,0
147,5
150,0
124,1
126,7
129,3
131,9
134,5
137,1
139,7
142,3
144,9
147,5
150,1
123,4
126,1
128,7
131,4
134,1
136,8
139,5
142,1
144,8
147,5
150,2
123,1
125,8
128,5
131,2
133,9
136,7
139,4
142,1
144,8
147,5
150,2
122,7
125,4
128,2
131,0
133,7
136,5
139,2
142,0
144,7
147,5
150,3
122,0
124,8
127,6
130,5
133,3
136,1
139,0
141,8
144,7
147,5
150,3
RCUE 240 WG2

HPD
38,9
40,4
41,9
43,4
45,0
46,6
48,2
49,8
51,4
53,1
54,8
38,7
40,2
41,7
43,2
44,8
46,4
48,1
49,7
51,4
53,1
54,9
38,3
39,8
41,4
43,0
44,6
46,2
47,9
49,6
51,3
53,1
54,9
37,8
39,4
41,0
42,7
44,3
46,0
47,7
49,5
51,3
53,1
55,0
37,7
39,3
40,9
42,5
44,2
45,9
47,7
49,5
51,3
53,1
55,0
37,4
39,1
40,7
42,4
44,1
45,8
47,6
49,4
51,2
53,1
55,0
37,0
38,7
40,4
42,1
43,8
45,6
47,4
49,3
51,2
53,1
55,0
IPT
110,7
111,5
112,3
113,1
113,9
114,7
115,5
116,3
117,1
117,8
118,6
119,2
119,9
120,6
121,4
122,1
122,8
123,6
124,3
125,0
125,7
126,5
133,3
134,0
134,6
135,2
135,8
136,4
137,0
137,7
138,3
138,9
139,5
147,5
148,0
148,5
149,0
149,5
150,0
150,5
151,0
151,6
152,1
152,6
153,1
153,6
154,1
154,5
155,0
155,5
155,9
156,4
156,9
157,3
157,8
161,6
162,0
162,4
162,8
163,2
163,6
164,0
164,4
164,8
165,2
165,6
175,8
176,1
176,4
176,6
176,9
177,2
177,5
177,8
178,1
178,4
178,7
CCAP
716,0
731,8
747,6
763,4
779,2
795,0
810,8
826,6
842,4
858,2
874,0
703,3
719,5
735,7
751,9
768,1
784,3
800,4
816,6
832,8
849,0
865,2
682,2
699,0
715,8
732,7
749,5
766,4
783,2
800,0
816,9
833,7
850,5
661,0
678,5
696,0
713,5
731,0
748,4
765,9
783,4
800,9
818,4
835,9
652,6
670,3
688,1
705,8
723,5
741,3
759,0
776,8
794,5
812,3
830,0
639,9
658,0
676,2
694,3
712,4
730,5
748,7
766,8
784,9
803,1
821,2
618,7
637,5
656,3
675,1
693,9
712,6
731,4
750,2
769,0
787,7
806,5
CFR
123,2
125,9
128,6
131,3
134,0
136,7
139,5
142,2
144,9
147,6
150,3
121,0
123,8
126,5
129,3
132,1
134,9
137,7
140,5
143,2
146,0
148,8
117,3
120,2
123,1
126,0
128,9
131,8
134,7
137,6
140,5
143,4
146,3
113,7
116,7
119,7
122,7
125,7
128,7
131,7
134,7
137,8
140,8
143,8
112,2
115,3
118,3
121,4
124,4
127,5
130,6
133,6
136,7
139,7
142,8
110,1
113,2
116,3
119,4
122,5
125,7
128,8
131,9
135,0
138,1
141,2
106,4
109,7
112,9
116,1
119,3
122,6
125,8
129,0
132,3
135,5
138,7
CPD
45,5
47,4
49,4
51,4
53,5
55,6
57,7
59,9
62,1
64,3
66,6
44,0
45,9
47,9
50,0
52,0
54,2
56,3
58,5
60,8
63,0
65,3
41,5
43,5
45,5
47,6
49,7
51,8
54,0
56,3
58,5
60,9
63,2
39,1
41,1
43,1
45,2
47,3
49,5
51,8
54,0
56,4
58,8
61,2
38,1
40,1
42,2
44,3
46,4
48,6
50,9
53,2
55,5
57,9
60,4
36,7
38,7
40,8
42,9
45,1
47,3
49,6
51,9
54,2
56,7
59,1
34,4
36,4
38,5
40,7
42,8
45,1
47,4
49,7
52,2
54,6
57,1

CPD:
IPT:
HCAP
837,9
854,6
871,2
887,9
904,6
921,3
937,9
954,6
971,3
987,9
1004,6
834,6
851,5
868,5
885,5
902,5
919,5
936,5
953,5
970,5
987,5
1004,4
829,0
846,5
864,0
881,5
899,0
916,6
934,1
951,6
969,1
986,6
1004,1
823,4
841,5
859,5
877,5
895,6
913,6
931,7
949,7
967,8
985,8
1003,9
821,2
839,4
857,7
875,9
894,2
912,5
930,7
949,0
967,2
985,5
1003,7
817,8
836,4
855,0
873,6
892,1
910,7
929,3
947,8
966,4
985,0
1003,6
812,3
831,4
850,5
869,6
888,7
907,8
926,9
946,0
965,1
984,2
1003,3
HFR
144,1
147,0
149,9
152,7
155,6
158,5
161,3
164,2
167,1
169,9
172,8
143,5
146,5
149,4
152,3
155,2
158,2
161,1
164,0
166,9
169,8
172,8
142,6
145,6
148,6
151,6
154,6
157,6
160,7
163,7
166,7
169,7
172,7
141,6
144,7
147,8
150,9
154,0
157,1
160,2
163,4
166,5
169,6
172,7
141,2
144,4
147,5
150,7
153,8
156,9
160,1
163,2
166,4
169,5
172,6
140,7
143,9
147,1
150,3
153,4
156,6
159,8
163,0
166,2
169,4
172,6
139,7
143,0
146,3
149,6
152,9
156,1
159,4
162,7
166,0
169,3
172,6
HPD
58,8
61,1
63,4
65,7
68,1
70,5
73,0
75,5
78,0
80,6
83,2
58,4
60,7
63,0
65,4
67,8
70,3
72,8
75,3
77,9
80,5
83,2
57,6
60,0
62,4
64,8
67,3
69,8
72,4
75,0
77,7
80,4
83,2
56,9
59,3
61,8
64,3
66,8
69,4
72,1
74,8
77,5
80,3
83,1
56,6
59,0
61,5
64,0
66,6
69,2
71,9
74,6
77,4
80,2
83,1
56,2
58,6
61,1
63,7
66,3
69,0
71,7
74,5
77,3
80,2
83,1
55,4
58,0
60,5
63,2
65,8
68,6
71,4
74,2
77,1
80,0
83,0
IPT
121,9
122,8
123,6
124,5
125,4
126,3
127,1
128,0
128,9
129,7
130,6
131,2
132,0
132,8
133,6
134,4
135,2
136,0
136,8
137,6
138,4
139,2
146,8
147,5
148,2
148,8
149,5
150,2
150,9
151,6
152,3
152,9
153,6
162,4
162,9
163,5
164,1
164,6
165,2
165,7
166,3
166,9
167,4
168,0
168,6
169,1
169,6
170,1
170,7
171,2
171,7
172,2
172,7
173,2
173,7
177,9
178,4
178,8
179,3
179,7
180,2
180,6
181,0
181,5
181,9
182,4
193,5
193,8
194,2
194,5
194,8
195,1
195,5
195,8
196,1
196,4
196,7
1 kW = 860 kcal/h
= 3412 Btu/h
1 kPa = 0.102 mAq

Performance Table (Heating Operation, Only for Heat Pump Operation Option)
RCUE40WG2
RCUE50WG2
RCUE60WG2
CLOT
HOT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
5,0
25,0
162,3
27,9
35,0
135,4
23,3
31,4
26,9
193,8
33,3
35,2
161,7
27,8
37,4
32,1
235,5
40,5
36,8
196,0
33,7
36,5
39,4
30,0
161,4
27,8
34,6
131,3
22,6
29,7
30,1
192,7
33,2
34,8
156,8
27,0
35,3
35,9
234,2
40,3
36,4
190,1
32,7
34,4
44,1
35,0
160,5
27,6
34,2
127,3
21,9
27,9
33,3
191,7
33,0
34,5
152,0
26,1
33,3
39,7
233,0
40,1
36,0
184,3
31,7
32,4
48,8
40,0
157,2
27,0
32,9
120,7
20,8
25,3
36,5
187,7
32,3
33,1
144,2
24,8
30,1
43,5
228,2
39,3
34,6
174,8
30,1
29,3
53,4
45,0
154,0
26,5
31,7
114,4
19,7
22,8
39,7
183,9
31,6
31,9
136,6
23,5
27,1
47,3
223,7
38,5
33,3
165,6
28,5
26,4
58,1
50,0
151,0
26,0
30,5
108,2
18,6
20,5
42,8
180,3
31,0
30,7
129,1
22,2
24,4
51,2
219,4
37,7
32,1
156,6
26,9
23,7
62,8
55,0
148,1
25,5
29,5
102,1
17,6
18,3
46,0
176,9
30,4
29,6
121,9
21,0
21,8
55,0
215,3
37,0
31,0
147,8
25,4
21,3
67,5
25,0
168,9
29,0
37,6
141,6
24,4
34,3
27,2
201,6
34,7
37,9
169,1
29,1
40,8
32,5
245,0
42,1
39,6
205,1
35,3
39,8
39,9
30,0
168,2
28,9
37,4
137,8
23,7
32,5
30,4
200,8
34,5
37,6
164,6
28,3
38,7
36,2
244,0
42,0
39,3
199,5
34,3
37,7
44,5
35,0
167,5
28,8
37,1
134,0
23,0
30,8
33,5
200,0
34,4
37,3
160,0
27,5
36,7
40,0
243,1
41,8
39,1
194,0
33,4
35,8
49,1
40,0
164,2
28,2
35,7
127,6
21,9
28,1
36,6
196,1
33,7
36,0
152,3
26,2
33,4
43,8
238,4
41,0
37,6
184,7
31,8
32,6
53,7
45,0
161,1
27,7
34,5
121,3
20,9
25,5
39,8
192,3
33,1
34,7
144,8
24,9
30,3
47,5
233,9
40,2
36,3
175,6
30,2
29,6
58,3
50,0
158,1
27,2
33,3
115,2
19,8
23,1
42,9
188,8
32,5
33,5
137,5
23,7
27,5
51,3
229,7
39,5
35,1
166,8
28,7
26,8
62,9
7,0
55,0
155,3
26,7
32,2
109,2
18,8
20,8
46,1
185,4
31,9
32,4
130,4
22,4
24,8
55,0
225,6
38,8
33,9
158,1
27,2
24,2
67,5
25,0
178,7
30,7
41,9
151,0
26,0
38,7
27,7
213,4
36,7
42,2
180,3
31,0
46,1
33,1
259,2
44,6
44,1
218,6
37,6
44,9
40,6
30,0
178,3
30,7
41,7
147,5
25,4
37,1
30,8
212,9
36,6
42,0
176,2
30,3
44,1
36,7
258,7
44,5
44,0
213,6
36,7
43,0
45,1
35,0
177,9
30,6
41,5
144,1
24,8
35,4
33,8
212,5
36,5
41,8
172,1
29,6
42,2
40,4
258,2
44,4
43,8
208,6
35,9
41,1
49,6
40,0
174,8
30,1
40,1
137,8
23,7
32,5
36,9
208,7
35,9
40,4
164,6
28,3
38,7
44,1
253,7
43,6
42,3
199,6
34,3
37,8
54,1
45,0
171,7
29,5
38,8
131,7
22,7
29,8
40,0
205,0
35,3
39,1
157,3
27,1
35,5
47,7
249,3
42,9
41,0
190,7
32,8
34,6
58,6
50,0
168,8
29,0
37,6
125,7
21,6
27,3
43,0
201,5
34,7
37,9
150,1
25,8
32,5
51,4
245,1
42,2
39,7
182,0
31,3
31,7
63,1
55,0
166,0
28,6
36,5
119,9
20,6
24,9
46,1
198,2
34,1
36,7
143,1
24,6
29,7
55,1
241,2
41,5
38,5
173,6
29,9
28,9
67,6
25,0
195,1
33,6
49,3
166,6
28,7
46,7
28,5
233,0
40,1
49,7
198,9
34,2
55,6
34,1
283,0
48,7
52,1
241,2
41,5
54,2
41,8
30,0
195,2
33,6
49,4
163,8
28,2
45,2
31,5
233,1
40,1
49,8
195,5
33,6
53,8
37,6
283,2
48,7
52,2
237,1
40,8
52,5
46,1
35,0
195,3
33,6
49,4
160,9
27,7
43,7
34,4
233,3
40,1
49,9
192,2
33,1
52,1
41,1
283,4
48,8
52,3
233,0
40,1
50,8
50,4
40,0
192,3
33,1
48,0
154,9
26,6
40,7
37,4
229,6
39,5
48,4
185,0
31,8
48,4
44,6
279,1
48,0
50,7
224,3
38,6
47,2
54,8
45,0
189,4
32,6
46,7
149,1
25,6
37,8
40,3
226,1
38,9
47,0
178,0
30,6
45,0
48,1
274,9
47,3
49,3
215,8
37,1
43,9
59,1
50,0
186,6
32,1
45,4
143,3
24,6
35,0
43,3
222,8
38,3
45,7
171,1
29,4
41,7
51,6
270,9
46,6
48,0
207,5
35,7
40,7
63,4
55,0
183,9
31,6
44,1
137,7
23,7
32,5
46,2
219,5
37,8
44,5
164,4
28,3
38,6
55,2
267,0
45,9
46,7
199,3
34,3
37,7
67,7
CLOT
HOT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
5,0
25,0
278,2
47,8
58,4
234,4
40,3
44,0
43,7
387,6
66,7
63,8
323,4
55,6
38,5
64,2
470,9
81,0
67,9
392,1
67,4
55,4
78,8
30,0
276,3
47,5
57,6
227,4
39,1
41,5
48,9
385,5
66,3
63,2
313,6
53,9
36,3
71,8
468,5
80,6
67,3
380,3
65,4
52,3
88,2
35,0
274,5
47,2
56,9
220,3
37,9
39,1
54,1
383,4
65,9
62,5
303,9
52,3
34,2
79,5
466,0
80,2
66,6
368,5
63,4
49,3
97,5
40,0
268,3
46,2
54,5
209,0
36,0
35,3
59,3
375,4
64,6
60,1
288,3
49,6
30,9
87,1
456,5
78,5
64,0
349,6
60,1
44,6
106,9
10,0
15,0
RCUE80WG2
7,0
10,0
15,0
RCUE100WG2
RCUE120WG2
45,0
262,5
45,2
52,3
198,0
34,1
31,8
64,5
367,8
63,3
57,8
273,1
47,0
27,9
94,7
447,4
76,9
61,6
331,1
57,0
40,2
116,2
50,0
256,9
44,2
50,2
187,3
32,2
28,6
69,7
360,6
62,0
55,7
258,3
44,4
25,1
102,3 438,7
75,5
59,4
313,2
53,9
36,2
125,6
55,0
251,7
43,3
48,2
176,8
30,4
25,6
74,9
353,8
60,8
53,7
243,8
41,9
22,5
109,9 430,6
74,1
57,3
295,7
50,9
32,4
134,9
25,0
289,5
49,8
63,0
245,2
42,2
47,9
44,3
403,2
69,4
68,8
338,3
58,2
41,9
65,0
489,9
84,3
73,2
410,1
70,5
60,4
79,8
30,0
288,0
49,5
62,4
238,6
41,0
45,5
49,4
401,6
69,1
68,3
329,1
56,6
39,8
72,5
488,1
83,9
72,7
399,1
68,6
57,3
89,0
35,0
286,5
49,3
61,8
232,0
39,9
43,1
54,5
400,0
68,8
67,8
320,0
55,0
37,7
80,0
486,2
83,6
72,2
388,0
66,7
54,3
98,2
40,0
280,5
48,2
59,3
220,9
38,0
39,2
59,6
392,2
67,5
65,3
304,7
52,4
34,3
87,5
476,8
82,0
69,6
369,4
63,5
49,5
107,4
45,0
274,7
47,3
57,0
210,0
36,1
35,6
64,7
384,7
66,2
62,9
289,7
49,8
31,2
95,0
467,9
80,5
67,1
351,2
60,4
45,0
116,6
50,0
269,3
46,3
54,9
199,4
34,3
32,3
69,8
377,6
64,9
60,7
275,1
47,3
28,3
102,5 459,3
79,0
64,8
333,5
57,4
40,8
125,8
55,0
264,0
45,4
52,8
189,1
32,5
29,2
74,9
370,8
63,8
58,7
260,8
44,9
25,6
110,0 451,3
77,6
62,7
316,2
54,4
36,9
135,0
25,0
306,5
52,7
70,3
261,4
45,0
54,2
45,1
426,8
73,4
76,6
360,6
62,0
47,3
66,2
518,4
89,2
81,6
437,2
75,2
68,2
81,2
30,0
305,5
52,5
69,8
255,5
43,9
51,8
50,1
425,8
73,2
76,3
352,3
60,6
45,3
73,5
517,4
89,0
81,3
427,2
73,5
65,2
90,2
35,0
304,5
52,4
69,4
249,5
42,9
49,5
55,1
424,9
73,1
76,0
344,1
59,2
43,3
80,8
516,4
88,8
81,0
417,2
71,8
62,4
99,2
40,0
298,7
51,4
66,9
238,6
41,0
45,5
60,1
417,3
71,8
73,4
329,2
56,6
39,8
88,2
507,3
87,3
78,3
399,1
68,6
57,3
108,2
45,0
293,1
50,4
64,5
228,0
39,2
41,7
65,0
410,0
70,5
71,0
314,5
54,1
36,5
95,5
498,6
85,8
75,7
381,4
65,6
52,6
117,2
50,0
287,7
49,5
62,3
217,7
37,4
38,2
70,0
403,1
69,3
68,7
300,3
51,6
33,4
102,8 490,2
84,3
73,3
364,1
62,6
48,2
126,2
55,0
282,6
48,6
60,2
207,6
35,7
34,8
75,0
396,4
68,2
66,6
286,3
49,2
30,5
110,1 482,3
83,0
71,1
347,1
59,7
44,0
135,2
25,0
334,8
57,6
83,2
288,4
49,6
65,3
46,4
465,9
80,1
90,4
397,8
68,4
57,0
68,1
566,0
97,3
96,4
482,3
83,0
82,1
83,6
30,0
334,7
57,6
83,2
283,5
48,8
63,2
51,2
466,2
80,2
90,5
391,0
67,3
55,2
75,2
566,4
97,4
96,5
474,1
81,6
79,5
92,3
35,0
334,6
57,6
83,1
278,6
47,9
61,2
56,0
466,5
80,2
90,6
384,3
66,1
53,4
82,2
566,9
97,5
96,7
466,0
80,1
76,9
100,9
40,0
329,0
56,6
80,5
268,3
46,1
56,9
60,8
459,2
79,0
88,0
370,0
63,6
49,7
89,2
558,2
96,0
93,9
448,6
77,2
71,6
109,5
45,0
323,7
55,7
78,0
258,1
44,4
52,8
65,6
452,2
77,8
85,5
356,0
61,2
46,2
96,3
549,8
94,6
91,2
431,6
74,2
66,5
118,2
50,0
318,5
54,8
75,6
248,1
42,7
49,0
70,4
445,5
76,6
83,1
342,2
58,9
42,8
103,3 541,7
93,2
88,7
414,9
71,4
61,7
126,8
55,0
313,5
53,9
73,4
238,3
41,0
45,4
75,2
439,1
75,5
80,8
328,7
56,5
39,7
110,3 534,0
91,9
86,3
398,6
68,6
57,2
135,4
Where,
CLOT: Chilled Water Outlet Temperature (C)
HOT: Hot Water Outlet Temperature (C)
HCAP: Heating Capacity (kW)
CCAP: Cooling Capacity (kW)

CPD:Water Cooler Pressure Drop (kPa)
IPT:Compressor Input Power (kW)
1 kW = 860 kcal/h
= 3412 Btu/h
1 kPa = 0.102 mAq

Performance Table (Heating Operation, Only for Heat Pump Operation Option)
RCUE150WG2
RCUE180WG2
CLOT
HOT
HCAP
HFR
HPD
CCAP
CFR
CPD
IPT
HCAP
5,0
25,0
533,6
91,8
86,1
449,7
77,3
71,9
83,9
629,6 108,3
30,0
530,0
91,2
85,1
436,2
75,0
67,9
93,8
625,5 107,6
29,2
514,6
88,5
28,3
110,9
35,0
526,4
90,5
84,0
422,6
72,7
63,9
103,8 621,3 106,9
28,8
498,6
85,8
26,6
122,7
40,0
514,7
88,5
80,4
400,9
69,0
57,8
113,7 607,4 104,5
27,6
473,0
81,4
24,1
134,4
45,0
503,5
86,6
77,1
379,8
65,3
52,2
123,7 594,2 102,2
26,5
448,1
77,1
21,7
146,2
50,0
492,8
84,8
74,1
359,2
61,8
46,9
133,6 581,7 100,0
25,4
423,7
72,9
19,5
157,9
55,0
482,7
83,0
71,2
339,1
58,3
42,1
143,6 569,7
98,0
24,4
400,0
68,8
17,5
169,7
25,0
555,3
95,5
92,9
470,4
80,9
78,3
84,9
655,3 112,7
31,9
554,9
95,5
32,7
100,3
30,0
552,4
95,0
92,0
457,7
78,7
74,3
94,7
651,9 112,1
31,6
540,0
92,9
31,0
111,9
35,0
549,5
94,5
91,1
445,0
76,5
70,5
104,5 648,5 111,5
31,3
525,0
90,3
29,4
123,5
40,0
538,0
92,5
87,5
423,7
72,9
64,2
114,3 634,9 109,2
30,0
499,8
86,0
26,7
135,1
45,0
526,9
90,6
84,1
402,8
69,3
58,4
124,1 621,9 107,0
28,9
475,3
81,7
24,3
146,7
50,0
516,4
88,8
81,0
382,5
65,8
52,9
133,9 609,5 104,8
27,8
451,3
77,6
22,0
158,2
87,1
7,0
HFR
HPD
CCAP
CFR
CPD
IPT
29,6
530,5
91,2
30,0
99,1
55,0
506,4
78,0
362,7
62,4
47,8
143,7 597,7 102,8
26,8
427,9
73,6
19,9
169,8
25,0
587,9 101,1 103,6
501,4
86,2
88,4
86,4
693,7 119,3
35,5
591,6 101,8
36,9
102,2
30,0
586,0 100,8 102,9
490,0
84,3
84,6
96,0
691,5 118,9
35,3
578,1
99,4
35,3
113,5
35,0
584,1 100,5 102,3
478,5
82,3
80,9
105,6 689,3 118,6
35,1
564,6
97,1
33,8
124,8
40,0
572,9
98,5
98,6
457,7
78,7
74,4
115,1 676,1 116,3
33,8
540,0
92,9
31,0
136,1
45,0
562,1
96,7
95,1
437,4
75,2
68,2
124,7 663,4 114,1
32,6
516,0
88,8
28,4
147,4
50,0
551,8
94,9
91,8
417,5
71,8
62,5
134,3 651,3 112,0
31,5
492,6
84,7
26,0
158,7
55,0
542,0
93,2
88,7
398,1
68,5
57,1
143,9 639,7 110,0
30,5
469,7
80,8
23,7
170,0
25,0
642,2 110,5 122,5
553,2
95,1
106,5
89,0
757,8 130,3
42,0
652,6 112,3
44,5
105,2
30,0
642,0 110,4 122,5
543,8
93,5
103,1
98,2
757,6 130,3
42,0
641,6 110,3
43,1
116,0
35,0
641,8 110,4 122,4
534,4
91,9
99,8
107,4 757,4 130,3
42,0
630,5 108,4
41,7
126,9
40,0
631,1 108,5 118,5
514,5
88,5
92,8
116,6 744,8 128,1
40,6
607,0 104,4
38,8
137,7
45,0
620,8 106,8 114,9
495,0
85,1
86,3
125,7 732,6 126,0
39,4
584,0 100,5
36,0
148,6
50,0
610,8 105,1 111,4
475,9
81,9
80,1
134,9 720,9 124,0
38,2
561,5
96,6
33,4
159,5
55,0
601,3 103,4 108,1
457,2
78,6
74,2
144,1 709,7 122,1
37,1
539,3
92,8
30,9
170,3
CLOT
HOT
HCAP
5,0
25,0
10,0
15,0
RCUE200WG2
7,0
10,0
15,0
HFR
HPD
CCAP
725,5 124,8
38,7
30,0
721,4 124,1
35,0
717,3 123,4
40,0
CFR
RCUE240WG2
CPD
IPT
HCAP
HFR
HPD
CPD
IPT
606,3 104,3
38,7
119,2
834,6
143,5 58,4
CCAP
703,3 121,0
CFR
44,0
131,2
38,3
588,1 101,2
36,5
133,3
829,0
142,6 57,6
682,2 117,3
41,5
146,8
37,8
569,9
98,0
34,4
147,5
823,4
141,6 56,9
661,0 113,7
39,1
162,4
702,2 120,8
36,3
540,6
93,0
31,1
161,6
805,0
138,5 54,5
627,1 107,9
35,3
177,9
45,0
687,8 118,3
34,9
512,1
88,1
28,0
175,8
787,5
135,5 52,3
594,0 102,2
31,8
193,5
50,0
674,2 116,0
33,6
484,3
83,3
25,2
189,9
770,8
132,6 50,2
561,8
96,6
28,6
209,1
55,0
661,3 113,7
32,4
457,2
78,6
22,5
204,1
755,0
129,9 48,2
530,3
91,2
25,6
224,7
25,0
754,9 129,8
41,7
634,2 109,1
42,2
120,6
868,5
149,4 63,0
735,7 126,5
47,9
132,8
30,0
751,7 129,3
41,4
617,1 106,1
40,0
134,6
864,0
148,6 62,4
715,8 123,1
45,5
148,2
35,0
748,5 128,7
41,0
600,0 103,2
37,9
148,5
859,5
147,8 61,8
696,0 119,7
43,1
163,5
40,0
733,7 126,2
39,5
571,2
98,3
34,5
162,4
841,5
144,7 59,3
662,6 114,0
39,2
178,8
45,0
719,5
123,8
38,1
543,1
93,4
31,3
176,4
824,2
141,8 57,0
630,1 108,4
35,6
194,2
50,0
706,0 121,4
36,7
515,7
88,7
28,4
190,3
807,8
138,9 54,9
598,3 102,9
32,3
209,5
55,0
693,2 119,2
35,5
489,0
84,1
25,6
204,2
792,1
136,2 52,8
567,3
97,6
29,2
224,8
25,0
798,9 137,4
46,4
676,1 116,3
47,6
122,8
919,5
158,2 70,3
784,3 134,9
54,2
135,2
30,0
797,1 137,1
46,2
660,6 113,6
45,6
136,4
916,6
157,6 69,8
766,4 131,8
51,8
150,2
35,0
795,2 136,8
46,0
645,2 111,0
43,6
150,0
913,6
157,1 69,4
748,4 128,7
49,5
165,2
40,0
780,8 134,3
44,5
617,2 106,2
40,0
163,6
896,1
154,1 66,9
715,9 123,1
45,5
180,2
45,0
767,0 131,9
43,0
589,8 101,4
36,7
177,2
879,3
151,2 64,5
684,1 117,7
41,7
195,1
50,0
753,8 129,7
41,6
563,0
96,8
33,6
190,8
863,1
148,5 62,3
653,0 112,3
38,2
210,1
55,0
741,2 127,5
40,3
536,8
92,3
30,6
204,4
847,8
145,8 60,2
622,7 107,1
34,8
225,1
25,0
872,3 150,0
54,9
745,9 128,3
57,5
126,5
1004,4 172,8 83,2
865,2 148,8
65,3
139,2
30,0
872,7 150,1
54,9
733,2 126,1
55,6
139,5
1004,1 172,7 83,2
850,5 146,3
63,2
153,6
35,0
873,1 150,2
55,0
720,6 123,9
53,8
152,6
1003,9 172,7 83,1
835,9 143,8
61,2
168,0
40,0
859,4 147,8
53,3
693,8 119,3
50,1
165,6
987,1
169,8 80,5
804,8 138,4
56,9
182,4
45,0
846,2 145,5
51,8
667,5 114,8
46,5
178,7
971,0
167,0 78,0
774,3 133,2
52,8
196,7
50,0
833,4 143,3
50,3
641,7 110,4
43,1
191,7
955,5
164,3 75,6
744,3 128,0
49,0
211,1
55,0
682,5 117,4
34,4
477,7
24,5
204,8
779,7
134,1 51,3
554,2
27,9
225,5
Where,
CLOT: Chilled Water Outlet Temperature (C)
HOT: Hot Water Outlet Temperature (C
HCAP: Heating Capacity (kW)
CCAP: Cooling Capacity (kW)
82,2

CPD:Water Cooler Pressure Drop (kPa)
IPT:Compressor Input Power (kW)
95,3
1 kW = 860 kcal/h
= 3412 Btu/h
1 kPa = 0.102 mAq
15.3. ELECTRICAL DATA
Model
RCUE 40WG2
RCUE 50WG2
RCUE 60WG2
RCUE 80WG2
RCUE100WG2
RCUE120WG2
RCUE150WG2
RCUE180WG2
RCUE200WG2
RCUE240WG2
Unit Main Power

(V)
400
400
400
400
400
400
400
400
400
400
(Hz)
50
50
50
50
50
50
50
50
50
50
Applicable
Instantaneous
Voltage (V)
Maximum
440
440
440
440
440
440
440
440
440
440
Minimum
360
360
360
360
360
360
360
360
360
360
Commpressor
Motor
STC*1
RNC
(A)
(A)
121
155
188
188
155
188
188
155
188
188
54,9
65,6
80,5
89,4
131,2
161,1
171,4
202,6
243,6
268,2
IPT
(kW)
Maximum
Unit
Current
(A)
STC*2
Unit
Maximum
(A)
33,5
40,0
49,1
54,5
80,0
98,2
104,5
123,5
148,5
163,5
69
82
101
112
164
201
214
253
304
335
121
155
188
188
172
209
209
190
230
230
NOTES:
1. This data is based on the following conditions
Chilled Water Inlet/Outlet Temperature: 12/7C,
AmbientTemperature: 35C.
2. The "Maximum Unit Current" shown in the above table is the maximum
total unit running current at the following conditions.
Supply Voltage: 90% of the rated voltage, Unit Capacity: 100% at max.
operating conditions
3. The power supply cables must be sized to cover this maximum current
value.
4. Starting Current (*1, *2) means as follows.
*1:First Compressor Starting Current
2
* :Unit Maximum Starting Current, when Last Compressor starts.
5. Compressor motor is star-delta starting
VOL: Rated Unit Supply Voltage(V)

STC: Starting Current(A)
Hz: Frequency(Hz)
RNC: Running Current(A)
IPT: Input(kW)
15.4. SOUND DATA

Standard Models
Sound Pressure Level (dB)
Frequency Band (Hz)
Model
Overall
63
125
250
500
1000
2000
4000
8000
RCUE40WG2
77
69
71
63
62
61
53
37
68
RCUE50WG2
74
76
71
64
65
64
51
35
69
RCUE60WG2
77
69
67
62
68
66
53
35
71
RCUE80WG2
77
70
70
71
62
64
50
39
71
RCUE100WG2
79
71
70
67
68
67
54
38
72
RCUE120WG2
80
72
70
65
71
69
56
38
74
RCUE150WG2
81
73
72
69
70
69
56
40
74
RCUE180WG2
82
74
73
71
70
69
56
41
75
RCUE200WG2
83
75
74
71
72
71
58
42
76
RCUE240WG2
84
76
75
71
73
72
59
42
77
Sound Power Level (dB)

Frequency Band (Hz)
Model
Overall
(dBA)
63
125
250
500
1000
2000
4000
8000
RCUE40WG2
92
84
86
78
77
76
68
52
83
RCUE50WG2
89
91
86
79
80
79
66
50
84
RCUE60WG2
92
84
82
77
83
81
68
50
86
RCUE80WG2
92
85
85
86
77
79
65
54
86
RCUE100WG2
95
87
86
83
84
83
70
54
88
RCUE120WG2
96
88
86
81
87
85
72
54
90
RCUE150WG2
97
89
88
85
86
85
72
56
90
RCUE180WG2
98
90
89
87
86
85
72
57
91
RCUE200WG2
99
91
90
87
88
87
74
58
92
RCUE240WG2
100
92
91
87
89
88
75
58
93
NOTE:
1. The sound pressure is based on the following conditions.
-1 meter from the control panel surface and 1.5 meter from the floor level.
-Voltage of the power source is 380V.
-The above data was measured in an anechoic chamber, so that reflected sound should be taken into consideration in
the field.
2. Operating conditions are as follows.
Standard Models: Cooler Water Inlet/Outlet Temperature 12/7 C, Condenser Water Inlet / outlet 30C/35C.
APPLICATION DATA 16/79
16. APPLICATION DATA

16.1. WORKING RANGE
Working Range
Item
Working Voltage
Voltage Imbalance
Power Supply
Condenser Water
Outlet Temperature
Starting Voltage
Standard
High Condensing
Temperature and Heat Pump
operation option
Standard
Cooler Water
Outlet Temperature
Description
90% 110% of Rated Voltage
Within 3% Deviation from Each Voltage
at Compressor Terminals
Higher than 85% of Rated Voltage
22 45
Remark
22 55
5 15
4 0 (Low 1)
-1 -5 (Low2)
-6 -10 (Low3)
1.0 MPa
Low Temperature
Option
Maximum Permissible Water Pressure
Water
Ethylene glycol
16.2. PART LOAD PERFORMANCE

The European Seasonal Energy Efficiency Ratio is a weighted formula enabling to take into account the variation of EER with
the load rate and the variation of water inlet condenser temperature.
ESEER = A . EER100 + B . EER75 + C . EER50 + D . EER25

The following part-load ratings shall be considered:
With the following weighting coefficients:
A = 0.03
B = 0.33
C = 0.41
D = 0.23
Load Ratio
(%)
100
75
50
25
Water temperature
at condenser inlet
(C)
30
26
22
18
Model RCUE-WG2
40
50
60
80
100
120
150
180
200
240
ESEER
4,52
4,52
4,52
4,86
4,52
4,52
4,86
4,86
4,52
4,86
16/80 APPLICATION DATA
16.3. ETHYLENE GLYCOL APPLICATION

Low Water Temperature Application (Option)
When utilizing water less than 5 C, antifreezing mixture of
ethylene glycol shall be input to the water system.
Low water temperature Option is categorised 3 level
depending on water outlet temperature.
Therefore, please specify the level when ordering .
Freeze Protection Thermostat has been set in the factory.
Table shows Required Ethylene Glycol percentage for each
category.
1. Category
Category
Outlet Water
Temp. (C)
Required
Ethylene
Glycol (wt%)
Low 1
Low 2
Low 3
4~0
-1 ~ -5
-6 ~ -10
20
30
40
Ethylene
Glycol
Freezing
Temp. (C)
-7
-13
-22
NOTE:
Freeze Protection Thermostat is the electronic control,
but non-adjustable.
For the performance, each value can be given by using following table. (See below example)
2. Performance
Ethylene
Glycol
(wt%)
20
30
40
Outlet
Water
Temp.
Flow Rate
Correction
Factor
Pressure
Drop
Correction
Factor
(C)
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10
(Kf)
1.011
1.012
1.013
1.013
1.014
1.034
1.035
1.037
1.037
1.038
1.073
1.075
1.076
1.076
1.077
(Kp)
1.15
1.16
1.17
1.18
1.19
1.30
1.32
1.34
1.36
1.38
1.50
1.52
1.54
1.56
1.58
Condenser Water Outlet Temperature

(C)
25
CAP IPT
(%)
(%)
97
79
94
78
92
78
90
78
88
77
84
77
82
76
80
76
78
75
75
75
72
73
70
73
68
72
66
72
64
71
NOTE:
1.CAP: Cooling Capacity, IPT: Compressor Input
2.Capacity and Compressor Input show the percentage
of the standard condition: Condenser Water Inlet /
Outlet 30/35c, Cooler.
3.Water Flow Rate and Pressure Drop can be calculated
by the Correction Factor Kf and Kp.
4.Example:
a)Model: RCUE120 WG2
b)Standard Condition: Capacity 388kW, Compressor
Input 98.2kW
c)Outlet/Inlet Water Temperature -3/2C, Condenser
Water Outlet Temp. 30C
30
CAP IPT
(%)
(%)
94
88
91
88
89
88
87
87
84
87
81
86
79
86
76
86
74
85
72
85
69
84
66
83
64
83
62
82
59
82
35
CAP CAP
(%)
(%)
91
98
88
98
86
97
83
97
81
97
78
96
75
96
73
96
70
95
68
95
65
94
62
93
60
93
57
93
55
93
40
IPT
(%)
88
85
82
80
77
74
71
69
66
64
61
58
56
53
51
IPT
(%)
107
107
107
107
106
106
106
106
105
105
104
103
103
103
103
45
CAP IPT
(%)
(%)
84
117
82
117
79
117
77
116
74
116
71
116
68
116
65
116
63
115
60
115
57
114
54
114
52
113
49
113
46
113
- Ethylene glycol: 30%

- Capacity = 388*0.76=295 kW, Compressor Input =
98.2*0.86=84.5 kW
- Water Flow(m/h) = Kf*Capacity(kW)*0.86T
(T=Inlet Temp.-Outlet Temp.)
= 1.037*295*0.86/(2-(-3))
= 52.6 m/h
- Pressure Drop = Kp*Pressure Drop (water)
1.897
= 1.34*0.0188*52.6
= 46 kPa
where, Pressure Drop(water)= x Q: see "Water
Pressure Drop"
COMPONENTS DATA 17/81
17. COMPONENTS DATA

17.1. COMPRESSOR
Model
40ASC-Z
Type
Revolution
Displacement
Capacity Control
Pneumatic Pressure
High Side
Low Side
Motor Type
Starting Method
Nominal Output
Poles
Insulation
Oil
Name
Charge
Net Weight
rpm
m3/h
%
137.4
MPa
MPa
50ASC-Z
60ASC-Z
Semi-Hermetic
2880
169.5
100 15, 0
208.7
3.0
2.0
Special Squirrel Cage, Three-Phase Motor
Star-Delta Starting
30
37
45
2
E
JAPAN ENERGY, FREOL UX300
6
400
440
460
kW
Litre
kg
17.2. CONDENSER AND WATER COOLER

CONDENSER
Model RCUE-WG2
Condenser
Type (Quantity)
40
50
A (1)
B (1)
TYPE
REFRIGERANT CYCLE
Dimensions
Height (H)
Width (W)
Depth (D)
Maximum Permissible Pressure
Refrigerant Side
Water Side
Internal Volume
Water Side
Material
Approval
60
80
100
120, 150
Brazed Type Plate Heat Exchanger
C (1)
D (1)
E (1)
F (1)
180, 200
240
C (3)
D (3)
A
40HP
B
50HP
C
60HP
D
80HP
E
100HP
F
120, 150HP
mm
mm
mm
525
243
272
525
243
338
525
243
431
525
243
497
694
304
441
694
304
538
MPa
MPa
1.8
1.0
1.8
1.0
1.8
1.0
1.8
1.0
1.8
1.0
1.8
1.0
Liter
14.8
18.6
23.9
27.6
Stainless Steel
PED ( 1 )
40.2
49.4
17/82 COMPONENTS DATA

WATER COOLER
Model RCUE-WG2
40
50
60
Water Cooler
Type (Quantity)
80
100, 120, 150
180, 200
240
C (3)
D (3)
Brazed Type Plate Heat Exchanger

A (1)
TYPE
REFRIGERANT CYCLE
Dimensions
Height (H)
Width (W)
Depth (D)
Maximum Permissible Pressure
Refrigerant Side
Water Side
Internal Volume
Water Side
Material
Approval
B (1)
C (1)
D (1)
E (1)
A
40HP
B
50HP
C
60HP
D
80HP
E
100, 120, 150HP
mm
mm
mm
525
243
227
525
243
305
525
243
389
525
243
431
694
304
489
MPa
MPa
1.8
1.0
1.8
1.0
1.8
1.0
1.8
1.0
1.8
1.0
Liter
15.1
16.7
21.5
23.9
Stainless Steel
PED ( 1 )
44.8
NOTE:
Pressure equipment Directive (97/23/EC)
SINGLE TYPE CONDENSER AND WATER COOLER
DUAL TYPE CONDENSER AND WATER COOLER

WATER OUT
WATER OUT
No.1 REFRIGERANT IN
REFRIGERANT IN
No.2 REFRIGERANT IN
WATER IN
WATER IN
REFRIGERANT OUT
No.1 REFRIGERANT OUT
No.2 REFRIGERANT OUT
REFRIGERANT
No.1 REFRIGERANT
No.2 REFRIGERANT
PLATES
WATER
PLATES
WATER
TCGB0045 - 12/06 - Printed in Spain

TC - Rcue 40 - 240 WG2 (TCGB0045 (12-06)

Uploaded by

Copyright:

Available Formats

TC - Rcue 40 - 240 WG2 (TCGB0045 (12-06)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TC - Rcue 40 - 240 WG2 (TCGB0045 (12-06)

Uploaded by

Copyright:

Available Formats

What are the main components of a water-cooled water chiller?

What are the main components of a water-cooled water chiller?

How does the refrigerant cycle work in the chiller?

How does the refrigerant cycle work in the chiller?

Technical Catalog

Installation, Operation and Maintenance Instructions.

3. OPERATION INSTRUCTIONS ................................................................................................... 4

4. COMPONENTS OF CHILLER .................................................................................................... 5

5. PREPARATION INITIAL CHECK ............................................................................................... 6

8. CONTROLLER ADJUSTMENT .................................................................................................. 26

9. SELF-INSPECTION FUNCTIONS .............................................................................................. 30

10. CONTROL SYSTEM ................................................................................................................. 36

12. TROUBLESHOOTING .............................................................................................................. 49

13. GENERAL SPECIFICATIONS .................................................................................................. 51

14. DRAWINGS ............................................................................................................................... 55

15. MODEL SELECTION ................................................................................................................ 70

16. APPLICATION DATA ............................................................................................................... 79

17. COMPONENTS DATA .............................................................................................................. 81

Immediate hazards which WILL result in severe

Hazards or unsafe practices which COULD result

Hazards or unsafe practices which COULD result

If you have any questions, contact your contractor or

(*) In case of High Condensing option and Heat Pump

2. FEATURES AND BENEFITS

HITACHI is a world leader in technology and with

A wide range of capacities are available from 134 kW to

FEATURES AND BENEFITS

INCORPORATES THE LATEST

Highly Reliable HITACHI Two-Pole

Built-in Oil Separator (Cyclone oil

Oil Sight Glass

TWIN SCREW COMPRESSOR

By having so few moving parts, it has become highly reliable

HITACHIs Continuous Capacity Control system uses

CONTINUOUS CAPACITY CONTROL

Cooling load = continuos capacity control

FEATURES AND BENEFITS

-PART LOAD PERFORMANCE-

MOTOR INPUT (%)

Thanks to Continuous Capacity Control, 15~20% energy

COOLING CAPACITY (%)

-CONTINUOUS CAPACITY CONTROL-

-CONVENTIONAL STEP CONTROLRestart

Combination of "Continuous Capacity

PLATE TYPE HEAT EXCHANGER

SHELL & TUBE

2.5. NEW ELECTRONIC EXPANSION VALVE

This unit is equipped with an electronic expansion valve to

Please contact your service shop, if this condition is

Oil Sight Glass

Power Wiring Supply

Pressure Relief Valve

High Pressure Switch

Economizer (only for 80, 150, 240 HP)

Solenoid Valve (only for 80, 150, 240 HP)

Liquid Sight Glass

Liquid Line Stop Valve

Electronic Expansion valve