Isolation Valve Selection (BP) PDF

RP 62-2
ISOLATION VALVE SELECTION

PHILOSOPHY FOR OIL AND GAS
PRODUCTION AND PROCESSING
September 1996
Copyright The British Petroleum Company p.l.c.
Copyright The British Petroleum Company p.l.c.

All rights reserved. The information contained in this document is subject
to the terms and conditions of the agreement or contract under which the
document was supplied to the recipient's organisation. None of the
information contained in this document shall be disclosed outside the
recipient's own organisation without the prior written permission of
Manager, Standards, BP International Limited, unless the terms of such
agreement or contract expressly allow.
BP GROUP RECOMMENDED PRACTICES AND SPECIFICATIONS FOR ENGINEERING

Issue Date
Doc. No.
RP 62-2
September 1996
Latest Draft No.
Document Title
ISOLATION VALVE SELECTION

PHILOSOPHY FOR OIL AND GAS
PRODUCTION AND PROCESSING
APPLICABILITY
Regional Applicability:
BPX
International
SCOPE AND PURPOSE

This Recommended Practice gives technical guidance for the selection of valves for land
based and offshore oil and gas processing facilities.
The main purpose of this document is to provide guidance to all new projects and
operating assets to help them minimize whole life cost whilst maintaining a consistent
approach to valve selection which acknowledges company experience.
AMENDMENTS
Amd
Date
Page(s)
Description
___________________________________________________________________
CUSTODIAN (See Quarterly Status List for Contact)
Valves
Issued by:-
Engineering Practices Group, BP International Limited, Research & Engineering Centre

Chertsey Road, Sunbury-on-Thames, Middlesex, TW16 7LN, UNITED KINGDOM
Tel: +44 1932 76 4067
Fax: +44 1932 76 4077
Telex: 296041
CONTENTS
Section
Page
FOREWORD ............................................................................................................... iii

1. INTRODUCTION................................................................................................... 1
2. APPLICATION....................................................................................................... 1
3. UNITS...................................................................................................................... 2
4. ASSUMPTIONS...................................................................................................... 2
5. MATERIALS .......................................................................................................... 2
6. CONSTRUCTION/ COMMISSIONING CONDITIONS ..................................... 2
7. ASSUMED CONDITIONS FOR OIL/ GAS PROCESSING................................ 2
8. RECOMMENDED VALVE SELECTIONS.......................................................... 3
9. MAINTENANCE CONSIDERATIONS ................................................................ 3
10. ISOLATION REQUIREMENTS ........................................................................... 4
11.
NOTES ON SPECIFIC VALVE TYPES AND APPLICATIONS .................. 5

11.1
11.2
11.3
11.4
11.5
Main ESD Valves ............................................................................................. 5

Pig launcher/Receiver Isolation ......................................................................... 5
Butterfly Valves................................................................................................ 6
Plug Valves ...................................................................................................... 7
Check Valves.................................................................................................... 8
12. RELATED ISSUES................................................................................................. 9

12.1
12.2
12.3
12.4
12.5
12.6
Weight/Cost Minimisation................................................................................. 9
Vent/Drain etc. Plugs...................................................................................... 10
Seal selection.................................................................................................. 10
Fugitive Emissions .......................................................................................... 11
Safety/ Relief Valves....................................................................................... 13
Subsea Application ......................................................................................... 13
TABLE 1. ASSUMED CONDITIONS FOR OIL AND GAS PROCESSING......... 15

TABLE 2. ISOLATING/BLOCK VALVE RECOMMENDATIONS..................... 17
RP 62-2
ISOLATION VALVE SELECTION PHILOSOPHY
FOR OIL & GAS PRODUCTION & PROCESSING
PAGE i
TABLE 3. CHECK VALVE RECOMMENDATIONS............................................ 21

APPENDIX A.............................................................................................................. 22
DEFINITIONS AND ABBREVIATIONS .............................................................. 22
APPENDIX B.............................................................................................................. 23
LIST OF REFERENCED DOCUMENTS............................................................... 23
RP 62-2
PAGE ii
FOREWORD
Introduction to BP Group Recommended Practice and Specifications for Engineering
The Introductory volume contains a series of documents that provide an introduction to the
BP Group Recommended Practices and Specifications for Engineering (RPSEs). In particular,
the 'General Foreword' sets out the philosophy of the RPSEs. Other documents in the
Introductory volume provide general guidance on using the RPSEs and background
information to Engineering Standards in BP. There are also recommendations for specific
definitions and requirements.
Value of this Recommended Practice
This Recommended Practice provides flexible valve type recommendations for the principal
areas of oil and gas processing facilities adherence to which should ensure that whole life cost
is minimised. The Recommended Practice also provides a benchmark against which
alternative proposals can be assessed.
Application
Text in italics is Commentary. Commentary provides background information which supports
the requirements of the Recommended Practice, and may discuss alternative options. It also
gives guidance on the implementation of any "Specification" or "Approval" actions; specific
actions are indicated by an asterisk (*) preceding a paragraph number.
Feedback and Further Information
Users are invited to feed back any comments and to detail experiences in the application of
BP RPSE's, to assist in the process of their continuous improvement.
For feedback and further information, please contact Engineering Practices Group, BP
Engineering or the Custodian. See Quarterly Status List for contacts.
RP 62-2
PAGE iii
1.
INTRODUCTION
Valve selection has a major effect on the whole life cost of an asset. The need to
replace malfunctioning equipment can soon wipe out CAPEX savings made by
inappropriate selection.
In the past, BP Exploration has lacked a means of ensuring that valve selections being
made by engineers working on new developments or asset refurbishment projects
followed a consistent pattern which accorded with the knowledge gained by the
company from operating and test experience. This document is intended to address
that deficiency.
The philosophy is commercially sustainable (i.e. there are sufficient qualified suppliers
of each recommended valve type to ensure competitive tendering or alternative
sourcing - not always the case in the past) and, where possible, alternatives are
proposed which may offer CAPEX or weight savings without unduly compromising
operating life. In some cases more expensive alternatives are listed which may be
found useful in especially onerous conditions.
In addition to providing general valve selection recommendations in Section 8,
particular applications and valve types (e.g. riser emergency shut down valves,
equipment isolation etc.) are addressed separately in Section 11. Important related
issues are dealt with in Section 12.
It is recognised that there will be unique conditions relating to certain projects which
have to be addressed; the aim of this Recommended Practice is to provide a benchmark
with which alternative proposals can be compared and against which they should be
justified.
This document is complimentary to BP Group RP 62-1 "Guide to Valve Selection" which contains
sufficient information for appropriate valve selections to be made but covers a much wider field than
oil and gas production. The high textual content of this document may, perhaps, have discouraged
busy project engineers from using it (but it should be noted that the computerised version (hypertext)
can produce valve selections very quickly).
BP Group RP 30-3 should be consulted by all those concerned with selecting or specifying actuated
shut-down valves and this document also provides recommendations covering control valves
2.
APPLICATION
This Recommended Practice is intended to be used by all new BP Exploration
development projects (and significant asset modification/refurbishment projects) as the
basis for a project specific valve selection philosophy. It has been written with a view
to minimising whole life costs (on which valves can have a major impact) and accords
with BP operating and test experience.
RP 62-2
PAGE 1
3.
UNITS
Units are SI metric except for nominal pipe size (NPS) which is stated with the DN
equivalent. Pressure units stated in bar refer to gauge pressures.
4.
ASSUMPTIONS
The assumptions made regarding operating conditions are clearly stated and cover the
most general case. Trim materials and, in some cases, valve types will have to be
altered where particular conditions require this.
5.
MATERIALS
This BP Group Recommended Practice is primarily concerned with functionality and
makes the assumption that valve pressure boundary materials will be selected to be
compatible with the connected pipe, the working fluid and the operating conditions.
Except as included in Section 12.1, specific material recommendations are not made.
BP Group RP 62-1 includes information on most commonly encountered valve materials.
6.
CONSTRUCTION/ COMMISSIONING CONDITIONS

Conditions during construction, line flushing and plant start-up are frequently the most
severe that a valve will see. Even where the normal operating conditions are clean,
soft seated valves can suffer permanent damage unless appropriate steps are taken to
protect them.
Selection of valves suitable for dirty service is the best course. Where this is not
possible consideration should be given to installing critical valves after flushing is
completed, although relative costs will have to be carefully evaluated. In the case of
soft seated ball valves of moderate to large size, protection by means of sealant
application has been shown to be effective and may offer the most economic
alternative.
BP Sunbury Branch report 124 240 deals with this topic and is available from the custodian of this
Recommended Practice.
7.
ASSUMED CONDITIONS FOR OIL/ GAS PROCESSING

For each zone of the system representing common operating conditions the assumed
fluid condition (clean, dirty, wet etc.), along with the assumed typical maximum
pressure and temperature are listed in Table 1. Where conditions are known to differ
from the assumed case, appropriate adjustments should be made. In most cases the
assumption is conservative, but not always (eg. fuel gas 'dry'). The recommendations
are largely unaffected by the form of the produced fluid (oil, gas, multiphase) although
RP 62-2
PAGE 2
this will have to be taken into account (isolation and low temperature potential of gas,
corrosivity of produced water etc.) when making a final selection.
8.
RECOMMENDED VALVE SELECTIONS

Table 2 provides a list of recommended isolation/block valve selections against each
zone of the system representing common operating conditions.
Table 3 provides similar recommendations for check valves.
Possible alternatives (which, in some cases, may offer CAPEX savings) are listed.
Most of the alternatives listed offer equivalent (or better) performance than the prime
recommendation. It should be recognised, however, that some risk of reduced operating life
(compared to the main recommendations) may be attached to a minority of these. Efforts to establish
the suitability of these valve types from several suppliers are ongoing (via the NEL Valve User Test
Consortium or, in some cases, field trials) but, until suitability is proven, caution is necessary. In
case of doubt consult the custodian of this RP.
It is not intended that these tables be issued to subcontractors, vendors etc. unless accompanied by
guidance from the project/ design contractor as to which alternatives are acceptable in the particular
circumstances. If this advice is ignored, the cheapest alternative is likely to be selected regardless of
any other considerations.
BP Group RP 62-1 provides detailed information on the merits/limitations of the different valve
types.
9.
MAINTENANCE CONSIDERATIONS
The maintenance strategy being adopted for valves on the facility can affect both the
ultimate choice of valve type and the spares requirements so it is important to establish
this early in the selection process.
If it is intended that work will be carried out in situ, welded pipe connections become
possible but valve internals will need to capable of being accessed and removed via the
bonnet etc. This facility is automatically provided in the case of gate valves, globe
valves, swing check valves, plug valves and top entry ball valves. However, the ease
with which internals can be withdrawn should be carefully investigated and it may be
necessary to provide lifting/handling facilities in the case of large valves. It should be
noted that in situ maintenance cannot be conducted on butterfly or wafer check valves.
Where the intention is to remove all valves to a workshop for maintenance maximum
flexibility of valve selection is possible. Spares holding may be increased, however,
because of the necessity to provide complete replacement valves.
RP 62-2
PAGE 3
10.
ISOLATION REQUIREMENTS
Where double block and bleed isolation is required by the isolation philosophy this can
be achieved in three ways:
(1)
Two single seated valves in series with a bleed from the connecting pipe.
(Acceptable for all applications.)
(2)
A single valve having two independent seats sealing in the same direction and a
connection into the cavity between the seats. (Cost savings may be realised by
using a valve of this type compared to (1) above)
The most suitable valve types are those where the seat load is applied mechanically to both upstream
and downstream seats simultaneously (e.g. expanding gate, wedge plug, expanding plug) i.e. they do
not rely on line pressure to provide the seating force. Certain types of wedge gate valve (e.g. split
wedge) may also be considered but sealing will not normally be as effective.
Valves which rely on the fluid pressure to provide a seal on both seats simultaneously (e.g. most slab
type (through conduit) gate valves with floating gate) would be the second choice for this duty and
are acceptable where sealing against very low pressure is not required.
Trunnion mounted ball valves having double sealing piston effect seats would be the third choice.
They should ideally only be used where it is impossible to accommodate other alternatives since the
second (downstream) seat will usually be effective only when the cavity has been pressurised. The
design relies on the difference in anular area between outer and inner seat to body seals and the seat
to ball seal which is located diametrically between them. This limits the freedom available to the
designer and care must be taken to ensure that the normal seating function (particularly of metal
seated ball valves) is not compromised. A solution to the latter problem is to make only the
downstream (in the isolation direction) seat a double piston design but this then makes the valves
directional.
In all such arrangements ensure that the vent (bleed) valve and pipework is of sufficient size to carry
away leakage past the upstream valve or seat (especially in gas service). This connection should also
be provided with a double block and bleed valve arrangement where access may be required in
service (e.g. for hot oil flushing of leaking valves).
(3)
An integral manifold incorporating two isolating valves and a bleed valve.
Integral valve manifolds are ideally suited to isolation of static branches (e.g. instruments) in small
sizes. For use in flowing systems or where wax, hydrates etc. are anticipated, manifolds should be
full bore type. Refer to EEMUA Publication 182 which incorporates a specification and set of
application guidelines for these items.
For larger line sizes there are manufacturers who offer manifolded arrangements of two ball, plug or
butterfly valves, in some cases with an overall length not exceeding that of a standard valve. It
should be noted that these are usually of drastically reduced bore compared to the pipe. The
potential effects of high velocity flow and increased pressure drop should be carefully considered
where their use is contemplated.
BP Group RP 44-10 gives guidance on isolation requirements for various operating conditions.
RP 62-2
PAGE 4
11.
NOTES ON SPECIFIC VALVE TYPES AND APPLICATIONS

11.1
Main ESD Valves

ESDVs which isolate the process system from risers or pipelines are
usually ball or gate valves fitted with a fail closed actuator. In theory
they can be soft seated but if sand is likely, or the valves have to pass
pigs, hard metal seated valves are more appropriate. Import risers and
pipelines should always be fitted with metal seated valves unless the
product is known to be thoroughly clean. A high degree of seat leak
tightness is not generally required and, although the "as constructed"
leak rate of metal seated valves will usually be worse than that of soft
seated valves it is likely to be maintained without significant
deterioration in adverse conditions. If soft seated valves can be
justified, some sort of seat protection should be provided during
installation/commissioning.
See BP Sunbury Branch Report 124-240, available from the custodian of this BP
Group Recommended Practice.
Ball valves having double sealing piston type seats are sometimes used
to provide two seals in series. For ESD service it is recommended that
only the inboard (process plant) side seat should have this facility. This
gives some additional security without degrading the performance of
the main (outboard) seat. Double sealing capability on both seats also
means the valve cavity may have to be fitted with a separate relief valve
since overpressure relief is no longer available via the seats. In such
cases the relief valve should be provided with double block and bleed
isolation onto the valve body to permit inspection/maintenance. When
defining test requirements for these relief valves it should be noted that
valve lift at pressures up to 133% of ESD valve rated pressure is
normally acceptable.
If drain and vent connections are provided on these and other important
valves (e.g. pig trap isolators) it is worth fitting them with a double
block and bleed valve arrangement since this will permit the valve cavity
to be accessed with the system live should the need arise (e.g. for hot
oil flushing to get a jammed seat to move).
The actuator and associated control system has a major influence on the
performance of ESD valves and should be chosen with care. BP Group
GS 130-6 and GS 134-1 provide guidance.
11.2
Pig launcher/Receiver Isolation

Valves isolating receivers (and launchers which may be reverse pigged)
have to be able to withstand debris being pushed through whilst giving
tight shut-off. Soft seated ball valves have consistently demonstrated
their inability to cope with this service. Through conduit slab gate
RP 62-2
PAGE 5
valves are the most appropriate choice and floating gate versions have
the advantage that they offer two isolations per valve (upstream and
downstream seat simultaneously) and can be provided with a cavity
bleed/vent valve. Expanding type gate valves which offer a positive
isolation regardless of line pressure combined with double block and
bleed in a single valve might be an even better choice (especially on gas
service) provided the actuator requirements are properly addressed.
ENP coated gates will usually be adequate in the case of launcher
valves.
Tungsten carbide coated ball valves will cope with the service but,
under certain operating conditions, can suffer from excessive leakage
when two are provided in series, due to the fact that the second valve
may not see a sufficient differential pressure to seat it.
Kicker valves and vent valves are used in throttling mode against a
differential pressure and should be capable of withstanding the resultant
high velocities (eg. on gas service) as well as providing tight shut-off.
Again, soft seated ball valves are not ideally suited and alternatives such
as balanced plug valves and (depending on pressure) triple offset
butterfly valves should be considered. Globe valves may be appropriate
for gas vent duty.
Receiver drain valves have to cope with highly abrasive service.
Quarter turn valves having a high degree of resistance such as tungsten
carbide coated balls, stellite coated balanced plugs etc. are the most
suitable choice.
At least one valve manufacturer offers a modified ball valve having a side entry
point which allows the insertion and removal of pigs. Whilst this may offer some
operational facility there is only a single isolation between the operator and the
process so the valve cannot be used on a live system unless additional isolating
valves are provided on either side.
11.3
Butterfly Valves
Lug type wafer or double flanged butterfly valves offer attractive cost and weight
savings over ball or gate types but are more sensitive to installation/handling. The
short overall length means that, once chosen, the operator cannot subsequently
change to another valve type without modifying piping. One way round this would
be to buy flanged valves having the standard overall length of ball valves etc. or to
fit a spool piece but this forfeits some of the cost/weight advantage.
Note that maintenance is only possible by breaking the pipe flange joint.
Butterfly valves are very economical of material and should receive

serious consideration for larger diameter, low pressure lines.
In clean service they can provide excellent isolation and triple offset
('tricentric') designs are particularly good in this respect. However
RP 62-2
PAGE 6
metal seated types rarely employ abrasion resistant material and erosion
of the seating faces can occur at high velocities in abrasive service (e.g.
when valve is almost closed) leading to seat leakage which exacerbates
the erosion. Test experience has been variable and caution is
recommended in selection. Nevertheless a few designs have performed
well in dirty service tests. (See Valve Test Summary report for further
details).
Since all butterfly valves are torque seated they are very sensitive to
errors/variations in the setting of end stops, air supplies etc.
All wafer type valves are potentially vulnerable to flange leakage in a
fire. For this reason only lugged or double flange designs should be
used and bolting material should be carefully selected. Fitting a steel
casing around the joint is another possibility.
11.4
Plug Valves
These quarter turn valves can be attractive where weight and cost must
be minimised. There are four types of interest:
(a)
Balanced, lubricated type (e.g. Serck Audco, Christensens,

Nordstrom) which usually rely on injection of lubricant to
provide a bubble tight seal;
(b)
Sleeved type (e.g. Durco, Tuflin) which utilise a PTFE sleeve;
(c)
Semi- balanced type incorporating a thrust bearing (Texsteam).
(d)
Lifting wedge plug type (Stockham, Goodwin)
"Regular" pattern valves usually have a rectangular flow passage giving

a reduced area compared to the pipe; "venturi" pattern have even
greater area reduction and neither can pass pigs. Full bore types are
available with corresponding increases in cost and weight. Flow areas
vary between manufacturers so care should be taken when making
comparisons.
Lubricated designs are only recommended where maintenance
procedures will include a re-lubrication schedule. Stellite coated
designs (and the Texsteam plated design) have been shown to cope with
abrasive service where maintenance lubrication is not carried out and
frequent operation is required (e.g. manifold/diverter service). ENP
balanced types may also offer acceptable service in this respect but have
not been proven on test or in service at time of writing. If use of
balanced valves without re lubrication is contemplated the supplier
should be advised so he can take appropriate measures to cope with the
increased operating torque.
RP 62-2
PAGE 7
Sleeved plug valves have been shown to be capable of acceptable

performance where abrasives are present in the product and have the
advantage that the working fluid is excluded from the valve body
cavity. They should be limited to low pressure ratings and have a
tendency for the operating torque to increase due to "bedding in" of the
plug if not operated or exercised regularly.
Wedge plug designs incorporate an actuating mechanism which lifts the
plug out of the body prior to turning. They can cope well with abrasive
or other difficult fluid conditions and may be worth consideration in the
smaller sizes.
11.5
Check Valves
BP Group RP 62-1 includes detailed discussion of the different types of
check valves and should be consulted when making selections. The
following points are included here for ease of reference:
(a)
The only check valves capable of passing pigs are special types
of swing checks. These do not generally have ideal dynamic
characteristics.
(b)
Tilting disk and duo-disk valves are better at coping with

unstable flows than standard swing checks. Axial flow designs
are best of all and should always be used at compressor outlets
unless there are pressing reasons for doing otherwise.
(c)
All check valves should be mounted at least three pipe diameters

downstream of pipe fittings (elbows, valves etc.).
(d)
Check valves should always be selected such that under normal

flow conditions they are fully open. Where swing check valves
are used in pigged pipelines this will not always be possible. In
such cases it is important to ensure that hinge pin and bearing
design is adequate for the constant disk movement which may
result.
(e)
Duo-disk, wafer type valves make extremely economical use of

expensive material. Where used they should be in lugged or
double flange form to reduce vulnerability. Bolting for lugged
designs should be thermally compatible with the valve body
material and flanges.
(f)
Lift type and swing type check valves should ideally not be
fitted in vertical pipes and no check valve should be mounted in
a pipe with flow vertically downward except axial flow type
where the supplier is fully appraised of the condition.
RP 62-2

PAGE 8
12.
RELATED ISSUES
12.1
Weight/Cost Minimisation
Where valves are being procured in expensive alloys the following
techniques should be considered as a way of minimising weight and
hence cost.
(a)
Use of compact connectors in place of standard ANSI etc.

flanges.
(b)
Selective use of corrosion resistant overlays.
(c)
Butt welding of valves to pipework.

Offers maximum weight saving but necessitates access through valve
bonnet for maintenance (automatic with gate valves, top entry ball valves
etc.). Note that, since top entry ball valves are usually heavier than end
entry, the weight saving in this case may not be large.
(d)
Use of pressure seal joints at the body/bonnet interface of high

pressure gate, check, top entry ball etc. valves.
This design uses a split ring to transfer the pressure load on the bonnet to
the body thus eliminating the heavy bonnet flange.
The joint should incorporate a graphite gasket, O ring or energised lip seal
- old style metal gaskets tend to leak at low pressure and can be difficult to
remove for maintenance.
(e)
Use of reduced bore valves wherever pigging is not a

requirement.
(f)
Use of butterfly valves.
(g)
In the case of large pipe sizes, use of intermediate rating valves

where design conditions fall between two standard pressure
ratings (e.g. between Cl 900 and Cl 1500).
This allows reduced wall thickness, smaller internal flanges etc. but should
be supported by sufficient analysis to provide confidence in the design.
Detailed analysis (e.g. FEA) may also be used to justify lighter
construction standard rated valves when these are specified in accordance
with pipeline valve standards. In such cases it is important to ensure that
adequate rigidity is retained.
(h)
Use of plug valves.

Regular or reduced bore
RP 62-2
PAGE 9
(i)
12.2
Use of a single valve (e.g. expanding gate) to provide double

block and bleed isolation instead of two independent valves.
Vent/Drain etc. Plugs

Taper threaded valve body plugs and needle type 'vent' plugs are a
common cause of leakage incidents on gas production systems. This is
usually due to a mixture of crevice etc. corrosion and poor mechanical
strength (excessive PTFE tape application etc.). Where valve body
connections are necessary for operational/testing reasons on larger size
valves consider terminating them with a blank flange or a flange + block
and bleed valve arrangement (see ESD above). Where not necessary
for operational reasons they should be eliminated (in this case,
manufacturer's claims that such body penetrations are necessary to
facilitate manufacture should be challenged).
Technical Bulletin TB 0005 (available from the custodian of this BP Group
Recommended Practice) provides guidance on this subject.
The same considerations apply to sealant injection fittings. Seat sealant

injection can sometimes assist in achieving a single isolation with a soft
seated ball valve but this operational advantage should be carefully
weighed against the number of additional potential leak paths being
introduced. Where used, fittings which incorporate double seated
check valves may offer improved integrity.
12.3
Seal selection
O ring (or other elastomer type) seals in valves on high pressure gas
service must have:
(a)
good resistance to the process fluids, dosing chemicals etc.
and
(b)
maximum resistance to explosive decompression.
Special formulations are available for use at pressures above 70bar

which have a relatively high hardness and include a filler to reduce gas
permeability. These must be used with high strength, plastic back-up
rings having low extrusion potential and scarf-cut joints.
At lower pressures high hardness will assist in resisting decompression
damage.
It should be noted that, in the case of rings having section diameters
above approx. 6 mm, it is very difficult to preclude e.d. damage unless
decompression rates are very low - regardless of material formulation.
RP 62-2
PAGE 10
In the case of very large ring sections damage may be inevitable owing
to the difficulty of avoiding manufacturing defects. Such seals should
be avoided where possible and alternatives (re-inforced plastic lip seals,
metal seals etc.) considered instead.
Valve suppliers knowledge of these considerations varies widely and seal selections
should be reviewed against
the recommendations of ESR.93.ER.151 (BP
Exploration's Elastomer Selection Guidelines) and ESR.93.ER.124 (Avoiding
Explosive Decompression damage in Seals), both available from the custodian of
this Recommended Practice.
12.4
Fugitive Emissions
There is currently great interest in reducing fugitive emissions of
volatile organic compounds from land based plants, the drivers being
both environmental and economic (loss control). Whilst the economic
factors may be less significant offshore (especially where gas is not
being exported) the environmental concerns are similar and ways in
which losses can be minimised should be considered at the design stage.
Because of the general activity in this area it should be possible to take advantage
of improved performance at little or no increase in cost.
Site surveys of conventional plant generally indicate that rising stem (globe type)
control valves are the worst culprits followed by rising stem (e.g. gate and globe)
isolating valves (note that small valves are often worse than larger sizes) with
conventional quarter turn valves (ball and plug) giving fewer problems. This is not
a surprising result.
Valve gland packings are a major source of these emissions and BP has
been conducting tests over a number years (principally on behalf of BP
Oil and BP Chemicals) in order to obtain an understanding of the
problem and explore possible solutions.
Tests on rising stem gate/globe (block valve) packings showed that:
1.
all graphite packings perform better than asbestos;
2.
that some quite simple low to medium density packings can give
very good performance;
3.
that the best performance was obtained from an "engineered"

design of packing with some pressure energising capability
(Garlok EVSP 9000);
4.
that graphite packings generally are relatively insensitive to stem

damage;
5.
that stem straightness and runout must be carefully controlled;
RP 62-2
PAGE 11
6.
that whilst good surface finish and close tolerances may give
improved sealing performance these parameters need not be
better than is currently being achieved by the leading valve
manufacturers.
Most manufacturers of rising stem (globe type) control valves have

done work on reducing emissions and offer valves fitted with "low
emission" packing arrangements at an increased price. Recent tests on
six manufacturer's valves indicate that:
1.
the majority performed well and it is possible to buy globe type

control valves with excellent low emission performance, some
of which are available with fire tested packing;
2.
the additional cost of valves fitted with low emission packings

as a percentage of total valve cost is not excessive in most cases
(this should be especially true in a project environment);
3.
good guidance of the valve stem is a prime requirement for

actuated valves;
4.
it seems that it is difficult to achieve good performance on

modulating duty with graphite packing, although one
manufacturer did succeed. The need to limit actuating forces
and hence packing friction is important in the case of control
valves and the best isolating (gate/globe) valve packing (with its
relatively high friction) did not perform well.
An alternative approach is to maximise the use of quarter turn control valves

(eccentric plug, ball, butterfly) in applications where operating conditions permit
and cavitation (etc.) problems do not arise.
Small (2") quarter turn valves (seat supported ball, sleeved plug and
butterfly) have also been tested. Stem seals covered a wide variety of
types from a single PTFE ring through O rings to packed glands.
Results indicate that:
1.
quarter turn valves should not be major sources of fugitive
emissions;
2.
standard designs should give acceptable sealing performance;
3.
there is no need to pay a premium for special "low emission"

arrangements;
4.
alignment of actuators to the valve stem can have a major effect

on performance.
RP 62-2
PAGE 12
It is possible that results might have been somewhat different for large valves but,
provided quality manufacturing ensures good concentricity/guidance of the stem
(especially in the case of actuated valves) emission problems should be avoided.
12.5
Safety/Relief Valves
General requirements for provision and selection of relief valves are
provided in BP Group RP 44-1.
The provision (and management) of spare valves along with the use of
bursting disk and buckling pin devices (especially where use of
expensive materials must be minimised) deserves careful consideration
if maximum operational facility is to be provided at minimum cost.
Bursting disks and buckling pins can sometimes be used to advantage in
parallel with spring loaded valves to facilitate 'on-line' changeout and
buckling pins have the advantages of greater accuracy, insensitivity to
fatigue and non-intrusive re-set.
Pilot operated valves may help to reduce losses to flare where operating
conditions are clean. Non-flowing pilot designs are usually to be
preferred.
A risk based approach to in-service inspection of these items is ideally suited to the
detail phase of a project where there is good knowledge of the reasons why
safety/relief valves have been provided. The technique involves making an
assessment of the probability that a valve will fail to fulfil its pressure relieving
function coupled with an assessment of the consequences of failure and (ideally) the
likelihood that it will be called upon to operate. A maximum inspection or
endorsement interval can then be derived. A flow chart based method for
performing such an assessment is available from the custodian of this
Recommended Practice.
12.6
Subsea Application
The general principles of this Recommended Practice are applicable to
subsea developments. However, to date, few such installations
undertake any processing so the conditions of Zone A must be assumed
to apply to the entire system.
Avoidance of maintenance and unscheduled intervention is paramount
and for this reason only the most robust, reliable and wear resistant
valve types should be considered. Seals must be long life, maintenance
free and not subject to degradation by the process.
For this combination of qualities, and in the light of experience to date,
it is hard to beat the tungsten carbide coated, slab gate valve.
Alternatives may become apparent as experience of subsea
developments accumulates. In the case of pipelines, ball valves offer a
proven alternative and valve selection should take into account the
particular process conditions and mode of operation eg. valves provided
RP 62-2
PAGE 13
to facilitate tie-ins are often required to seal until after the tie-in is made
then function as a piece of pipe. Soft seated valves supplied (and left)
in the closed position may be most suitable for this service. Other
valves (eg. associated with pigging operations) will need to be debris
tolerant to provide repeatable sealing over a long life. All valves will
have to survive flushing and line clearing (see above) and may need to
be protected during these operations.
RP 62-2
PAGE 14
SYSTEM/ ZONE
DESCRIPTION
PRESSURE
(A)
Flowlines,
Diverters, Manifolds
etc.
Import & Infield
Pipelines
(B)
Stabilisation/
Processing
(liquid line)
Stage 1
Stage 2
Usual case is gas/oil/water

mixture. In the case of new
developments it should always be
assumed that sand will be present
(dirty service).
2 Phase flow after interstage
contr. valve. Still some sand/
water until after LP separator.
De-salters (where provided)
10-90 bar
< 150C
assumed to come after LP sep. < 10 bar
< 80C
treat as "export oil".
< 90 bar reducing < 150C at HP Usually high sand content & can
Sand
through system
separator cooling be very corrosive.
treatment can involve high cycle
thereafter
abrasive service.
2 - 250 bar
0.5 to 2% water (max.) by wt.
< 60C
Relatively sweet even on sour
service.
<90 bar
Wet & dirty initially.
< 150C
Clean service after scrubbers.
< 10 bar before < 80C
Wet but generally clean except
compression.
where high sand content in
product.
Clean service after scrubbers.
< 80 bar
Generally clean service but some
< 100C
dryers (e.g. mol. sieves) can
introduce abrasive particles.
Switching valves subject to high
< 300C
cycle wear. Potential for low
< 200C
temperatures
exists
(-20C)
- 30/40C min.
throughout gas system.
< 170 bar
service
but
valves
< 120C at comp. Clean
associated
with
pigging
outlet,
operations may see abrasive
<60C at exp
debris and flow at high
differential pressure.
(C) Produced Water

(upstream of settling
tanks)
(D) Export Oil
(E) Gas from HP

separator
(F) Gas from LP
separator
(G) Gas Treatment

(drying, sweetening
etc.)
Mol. Sieves
Glycol, sweetening
Dew point proc.
(H) Export gas
< 200 bar (oil)

< 500 bar gas
TEMPERATURE
NOTES & ASSUMPTIONS RE.

SERVICE CONDITIONS
< 150C
TABLE 1. ASSUMED CONDITIONS FOR OIL AND GAS PROCESSING
RP 62-2
PAGE 15
(I) Gas re-injection
< 350 bar
< 150C
(J) Lift gas
< 350 bar
< 150C
< 80 bar
(K) Fuel gas
(L) Vent/ Flare/
Relief
< 12 bar
H.P.Flare
< 1.5 bar
L.P. Flare
(M)
Condense As for main system
returns
(N) Open Drains
As for main system
(O) Closed drains
As for main system
(P) Water Injection
< 250 bar
< 100C
Clean service and dry but may be

wet where corrosion etc. not a
problem.
Clean service.
Dry if high
pressure, otherwise may be wet.
Clean service and usually dry.
Clean service.
-100C min (gas)

-40C min (oil)
< 60C
As
for
main Condense from HP & LP
system
scrubbers etc. assumed to be
dirty.
Condense from dryers &
downstream
scrubbers
etc.
assumed to be clean.
As
for
main Only used for wash out/ purge
system
with water or N2. Not onerous
service.
As
for
main Assume dirty service where this
system
assumption is made for associated
system
Filtered at LP and sand free after
< 20C
pressurisation.
Notes:
When making selections for wet gas systems the erosion/corrosion potential of entrained liquid
should be considered.
TABLE 1. ASSUMED CONDITIONS FOR OIL AND GAS PROCESSING (CONT.)
RP 62-2
PAGE 16
ZONE
A
PRIMARY
COMMENTS & ALTERNATIVES
RECOMMENDATION
(Notes)
Slab type gate, tungsten carbide These will be comparably priced. Both can
handle service but gate v. will give better
(WC) coated;
isolation. (1)
Trunnion ball, WC coated;
Acceptable Alternatives: (2)
Stellite coated balanced plug; (3)
Rotating disk ("Everlasting"); (3)
Eccentric ball ("Orbit");
Semi-balanced plug ("Texsteam" - limited
range). (3)
Axial piston (Mokveld)
Note: In the case of infrequently operated
valves in pipelines where sand content is
low, soft seated trunnion ball valves may be
possible provided they receive adequate
protection during installation/flushing etc.
Slab type gate, WC coated;
Where sand content low, Stage 2 may be
Trunnion ball, WC coated
treated as D below.
Acceptable Alternatives
If sand exists for only very limited period,
ENP coated gate valve may offer necessary
abrasion resistance combined with good
isolation at economic cost; (4)
Stellite coated balanced plug;
Sleeved plug (possible for lower pressure
ratings and smaller sizes but ideally need
regular exercising);
Other alternatives as for zone A.
(See below for import line ESDV and pig
trap applications.)
Rotating disk ('everlasting');
All
types
need
careful
material
Balanced plug, stellite coated;
selection/corrosion protection.
Semi-balanced plug;
Eccentric ball;
Slab gate WC coated.
Wedge gate if little sand;
Sleeved plug for lower pressure ratings (but
ideally need exercising regularly);
TABLE 2. ISOLATING/BLOCK VALVE RECOMMENDATIONS
RP 62-2
PAGE 17
E1
(prior to
knockout)
E1
(after
knockout)
F
Applications other than pig

trap isolation:
Trunnion ball, soft seated;
Wedge gate (smaller sizes).
Pig trap isolation valves (see
section 11.2):
Slab gate; (ENP or WC
coated)
Expanding gate;
Trunnion ball, WC coated.
Slab gate;
Trunnion Ball, WC coated;
Stellite coated balanced plug.
Given appropriate material selection, most
high pressure valve types listed above would
be acceptable for the non-pig trap isolation
service.
ENP coated gate could offer necessary

abrasion resistance at economic cost. (4)

Wedge gate;
Slab gate, ENP coated.
Acceptable alternatives
Butterfly (< Cl 600)
ENP coated balanced plug (4)
Trunnion ball, soft seated (seat

supported 6");
Wedge gate;
Slab gate, ENP coated; (4)
Wedge gate;
Butterfly;
ENP coated balanced plug. (4)
Sleeved plug (smaller sizes)
Switching/recycle valves associated with
some gas dryers must withstand high cycle
wear e.g.
Eccentric ball;
Balanced plug, stellite coated;
Rotating disc.
High and low temperatures will affect
selection.
Butterfly ( Cl 600);
TABLE 2. ISOLATING/BLOCK VALVE RECOMMENDATIONS (CONT.)
RP 62-2
PAGE 18
I&J
M1
(clean)
M2
(dirty)
General Isolation (other than

pig trap):
wedge gate (small sizes);
Pig trap isolation valves (see
Section 11.2):
Slab gate; (ENP or WC coated)
Expanding gate;
Trunnion ball, WC coated.
Throttling
duty
(bypass,
blowdown etc.)
ENP coated balanced plug;
Trunnion ball, W.C. coated;
Slab gate, ENP coated;
Balanced plug, ENP coated;
Trunnion ball, soft seat (except
where operated against high p).
be acceptable for the non-pig trap isolation
service. However, careful consideration
should be given to sealing integrity,
tolerance of high differential pressure and
low temperature tolerance.
Triple offset, metal seated butterfly (
C1600) may be considered for some
throttling duties.
be acceptable.
However, careful
consideration should be given to sealing
integrity, tolerance of high differential
pressure and low temperature tolerance.
Trunnion ball, soft seated (seat Acceptable alternatives
Butterfly;
supported 6");
Wedge gate;
Butterfly;
Trunnion ball, soft seated
(seat supported 6")
Trunnion ball, soft seated (seat
supported 6");
Slab gate;
Trunnion Ball, WC coated;
Wedge Gate;
Stellite coated balanced plug.
If little sand ENP coated gate could give

necessary abrasion resistance at economic
cost - otherwise WC coated.
Sleeved plug (< Cl 600).
Seat supported ball/trunnion ball, Depending on pressure rating
soft seated;
Globe
RP 62-2
PAGE 19
As for main system
- Sleeved Plug ((<CL600) for dirty service
- Globe
Trunnion ball, soft seated (except Acceptable alternatives
where operated against high p Butterfly in L.P.
or water not sand free, in which Wedge gate.
case see I & J above)
Notes:
(1) It is sometimes difficult to accommodate slab gate valves in existing piping systems because of their height
but this should never be a problem with a new development where the design contractor should consider
their use from the outset.
(2) Suppliers of valves intended for dirty service should have demonstrated good performance in a type test
conducted by BP or NEL unless there is sufficient operating experience in similar service to give
confidence of successful application.
(3) Particularly suited to frequent operation and higher sand content.
(4) Electroless nickel plating is porous as is chrome plating. Base material selections must exhibit adequate
resistance to corrosion by the working fluid.
RP 62-2
PAGE 20
ZONE
A
2" NPS ( DN 50)

Ball check, hard faced,
straight or "Y" pattern (1)
> 2" NPS (DN 50)

Duo-disk wafer check, hard faced or rubber
seated with metal back-up.
Swing check, hard faced; (2)
Axial flow "non-slam" check; (3)
Tilting disk check. (3)
B
As for zone A
As for zone A
C
Ball check, hard faced, straight or Duo-disk wafer check, hard faced or rubber
"Y" pattern (1);
seated with metal back-up;
Diaphragm check.
Swing check. (2)
D
Piston check. (1)
Duo-disk wafer check;
Swing check.
E1
Ball check; (1)
Duo-disk wafer check, hard-faced or rubber
(prior
to
seated with metal back-up;
knock-out)
Acceptable alternative
Swing Check
E2
Piston check; (1)
Duo-disk wafer check.
(after
knock-out)
Swing check
F
As for E2
As for E2
G
As for E2
Axial flow check.
H
As for E2
Axial flow check (4)
Tilting disk check.
I&J
As for H
As for H
K
As for H
As for H
L
As for H
M1
Piston check;
(clean)
Ball check. (1)
Swing check.
M2
Ball check (1)
Duo-disk wafer check, hard faced or rubber seat
(dirty)
with metal back-up;
Swing check, hard faced.
N
Piston/Ball check (1)
Swing check
O
As for main system
As for main system
P
Piston/Ball check (1)
Swing check
Notes:
(1) Where "in line" type ball or piston check valves are used in horizontal pipes they must be fitted
with a closing spring. Consider piston type where frequent flow/pressure variations expected.
(2) Wafer style, single disk check valves are not recommended.
(3) Usually only to satisfy diversity requirements in this service.
(4) Must be used at outlet of reciprocating compressors
TABLE 3. CHECK VALVE RECOMMENDATIONS
RP 62-2
PAGE 21
APPENDIX A
DEFINITIONS AND ABBREVIATIONS
Definitions
Standard definitions may be found in the BP Group RPSEs Introductory Volume.
Abbreviations
ANSI
CAPEX
DN
EEMUA
ENP
ESD
ESDV
FEA
NEL Ltd
NPS
PTFE
WC
American National Standards Institute

Capital Expenditure
Nominal Diameter
Engineering Equipment and Material Users Association
Electroless Nickel Plate
Emergency Shutdown
Emergency Shutdown Valve
Finite Element Analysis
Formally National Engineering Laboratory
Nominal Pipe Size
Polytetrafluoroethylene
Tungsten carbide
RP 62-2
PAGE 22
APPENDIX B
LIST OF REFERENCED DOCUMENTS
A reference invokes the latest published issue or amendment unless stated otherwise.
Referenced standards may be replaced by equivalent standards that are internationally or
otherwise recognised provided that it can be shown to the satisfaction of the purchaser's
professional engineer that they meet or exceed the requirements of the referenced standards.
BP Documents
BP Group RP 62-1
Guide to Valve Selection
BP Group RP 30-3
Instrument and Control - Selection and use of Control and

Shutoff Valves.
BP Group RP 44-1
Overpressure Protection Systems
BP Group RP 44-10
Isolation of Equipment for Maintenance
BP Group GS 130-6
Actuators for Shut-off Valves
BP Group GS 134-1
Hydraulic Power Supplies
BP Group ESR.93.ER.151
Elastomar Selection Guidelines
BP Group ESR.93.ER.124
Avoiding Explosive Decompression damage in Seals
BP Group TB0005
Auxiliary Connections in Valve Bodies
BP Sunbury Branch
Report 124 240
The Protection of Valve Seat during Commissioning by use of

Silicon Sealant
Others
EEMUA 182
Specification & Application Guidelines for Integral Block &

Bleed Valve Manifolds for Direct Connection to Pipework.
RP 62-2
PAGE 23

Isolation Valve Selection (BP) PDF

Uploaded by

Copyright:

Available Formats

Isolation Valve Selection (BP) PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Isolation Valve Selection (BP) PDF

Uploaded by

Copyright:

Available Formats

RP 62-2

ISOLATION VALVE SELECTION

Copyright The British Petroleum Company p.l.c.

Copyright The British Petroleum Company p.l.c.

BP GROUP RECOMMENDED PRACTICES AND SPECIFICATIONS FOR ENGINEERING

Latest Draft No.

ISOLATION VALVE SELECTION

SCOPE AND PURPOSE

CUSTODIAN (See Quarterly Status List for Contact)

Engineering Practices Group, BP International Limited, Research & Engineering Centre

FOREWORD ............................................................................................................... iii

NOTES ON SPECIFIC VALVE TYPES AND APPLICATIONS .................. 5

Main ESD Valves ............................................................................................. 5

12. RELATED ISSUES................................................................................................. 9

TABLE 1. ASSUMED CONDITIONS FOR OIL AND GAS PROCESSING......... 15

TABLE 3. CHECK VALVE RECOMMENDATIONS............................................ 21

CONSTRUCTION/ COMMISSIONING CONDITIONS

ASSUMED CONDITIONS FOR OIL/ GAS PROCESSING

RECOMMENDED VALVE SELECTIONS

An integral manifold incorporating two isolating valves and a bleed valve.

NOTES ON SPECIFIC VALVE TYPES AND APPLICATIONS

Main ESD Valves

Pig launcher/Receiver Isolation

Butterfly valves are very economical of material and should receive

Balanced, lubricated type (e.g. Serck Audco, Christensens,

Sleeved type (e.g. Durco, Tuflin) which utilise a PTFE sleeve;

Semi- balanced type incorporating a thrust bearing (Texsteam).

Lifting wedge plug type (Stockham, Goodwin)

"Regular" pattern valves usually have a rectangular flow passage giving

Sleeved plug valves have been shown to be capable of acceptable

Tilting disk and duo-disk valves are better at coping with

All check valves should be mounted at least three pipe diameters

Check valves should always be selected such that under normal

Duo-disk, wafer type valves make extremely economical use of

ISOLATION VALVE SELECTION PHILOSOPHY

Use of compact connectors in place of standard ANSI etc.

Selective use of corrosion resistant overlays.

Butt welding of valves to pipework.

Use of pressure seal joints at the body/bonnet interface of high

Use of reduced bore valves wherever pigging is not a

Use of butterfly valves.

In the case of large pipe sizes, use of intermediate rating valves

Use of plug valves.

Use of a single valve (e.g. expanding gate) to provide double

Vent/Drain etc. Plugs

The same considerations apply to sealant injection fittings. Seat sealant

good resistance to the process fluids, dosing chemicals etc.

maximum resistance to explosive decompression.

Special formulations are available for use at pressures above 70bar

all graphite packings perform better than asbestos;

that the best performance was obtained from an "engineered"

that graphite packings generally are relatively insensitive to stem

that stem straightness and runout must be carefully controlled;

Most manufacturers of rising stem (globe type) control valves have

the majority performed well and it is possible to buy globe type

the additional cost of valves fitted with low emission packings

good guidance of the valve stem is a prime requirement for

it seems that it is difficult to achieve good performance on

An alternative approach is to maximise the use of quarter turn control valves