Band Pass Filter Design Part 3. Band Pass Filters From First Principles Richard Harris G3OTK

Band pass filter design
Part 3 - Using Nortons Transform

Richard Harris G3OTK
1. Introduction
Part 1 gave the procedure for design a third order filter from first principles. Sometimes it is
necessary to change the filter impedance part way through the filter, perhaps so that standard
values of inductors can be used or to give an insertion gain. One method is Nortons Transform
and Part 3 of this series demonstrates its use.
The filter developed in Part 1 Fig. 14 had the following specification:
Chebychev with 1dB pass band ripple (so that the ripple is visible on simulations)
Third order, capacitor input

Centre frequency (Fo) of 10MHz
Bandwidth (FBW) of 500kHz
The terminating resistance at the input and output was 2,540 Ohms if another terminating
resistance is required then a matching section must be used, and this will be discussed in Part 7
of this series.
The circuit diagram is shown in Fig 1.
2.54k
8.93p
8.93p
R1
C4
C5
Probe1-NODE
AC 1
V1
1u
L1244.4p
C1
2.54k
R2
1u
L3244.4p
C3
1u
L2235.4p
C2
Fig. .1. Filter circuit
dB(Probe1-NODE)-dB(Probe2-NODE) / dB
The insertion loss, as predicted by the SPICE simulator (Ref. 1), is shown in Fig. 2.
0
-5
-10
-15
-20
-25
-30
-35
-40
8.5
9.5
10
Frequency/MHertz
10.5
11
11.5
12
500kHertz/div
Fig. 2. Insertion loss
Version 1
Page 1
2. Nortons Transform
Nortons Transform (Refs. 2 & 3) is a useful technique for changing the impedance within a
filter. This might be necessary to equalise inductor values, or to change a non-standard
inductor value to a standard value or to ensure impedance matching with a load, such as the
input to an amplifier. The purpose of Part 3 of this series is to demonstrate this Transform. Part
4 will describe an alternative method.
On the left hand side of Fig. 9 is a capacitor connected in series with the primary winding of an
N-to-1 transformer. This combination can be replaced by three capacitors, as shown on the
right hand side. Of course the circuit on the right doesnt give the same isolation as that on the
left but that is not what we are trying to achieve.
(1 N) C
NC
N (N 1) C
N:1
Fig 3. Nortons Transform
So how is it possible to replace a capacitor and a transformer with just three capacitors, and,
perhaps more to the point, what if the transformer is a step-up transformer? How can you get a
higher voltage out of a combination of just three capacitors? The answer is quite simply that
one of the capacitors, either one on the left or the one on the right, will have a negative value.
We met negative capacitors in Part 1 and, whilst they are not physically realisable, the concept
can still be used, providing that there is a parallel capacitor that has a larger value so that the
combination is still positive. At a single frequency a negative capacitor can be replaced by an
inductor and this explains why it is possible to get a voltage step-up.
To demonstrate Nortons Transform, we will increase the impedance of the filter by a factor of
2.2 so that L3 is increased from 1uH to 2.2uH whilst keeping L1 and L2 at 1uH.
The
terminating resistance R2 must be increased and C3 must be reduced by the same factor.
Recall that transformers change impedance levels by the square of the number of turns, so the
turns ratio, N, of our notional transformer in Fig. 9 will be the square root of the ratio of L1 to L3,
which is 0.674.
Taking the right-hand side of the circuit diagram, as shown in Fig. 4.
8.93p
Probe1-NODE
C5
1u
L3
244.4p
C3
2.54k
R2
Fig 4. Right hand side of filter
Next add a transformer with a ratio of 0.674:1 between C5 and L3/C3/R2, whilst increasing the
value of L3 and R2 by a factor of 2.2 and reducing C3 by the same factor.
Version 1
Page 2
8.93p
Probe1-NODE
C5
TX1
P1
2.2u
L3
S1
111.1p
C3
5.588k
R2
Transformer
0.674 : 1
Fig. 5. Transformer added to increase impedance
Nortons Theorem enables us to replace C5 and TX1 by three capacitors.

6.02p
Probe1-NODE
C5
2.91p
C6
-1.96p
C7
2.2u
L3
111.1p
C3
5.588k
R2
Fig. 6. Replacing C5 and transformer with Nortons Transform capacitors
Now, although C7 is a negative value capacitor, it can be absorbed into C3, reducing it slightly.
C6 can be absorbed into C2 (see Fig. 1), increasing it slightly. So we have the final circuit
diagram for this filter
2.54k
8.93p
R1
C4
AC 1
V3
1u
L1
6.02p
Probe1-NODE
244.4p
C1
1u
L2
C5
238.3p
C2
2.2u
L3
109.1p
C3
5.588k
R2
Fig 7. Filter final circuit diagram
Version 1
Page 3
The insertion losses of the original filter in Fig. 1 and the modified filter in Fig. 7 can be
simulated and are shown in Fig. 8. The red curve is the response of the filter of Fig. 7. The
modified filter has an insertion gain because of the unequal terminating resistances. This gain
is the square root of the ratio of the output and input terminating resistances, 3.42 dB.
5
0
-5
dB
-10
-15
-20
-25
-30
-35
-40
8.5
9.5
10
10.5
Frequency/MHertz
11
11.5
12
500kHertz/div
Fig 8. Insertion losses of Fig. 1 and Fig. 7.
3. Conclusion
Nortons Transform can be used to increase the impedance within a filter so that standard
value, or specific value inductors can be used. The terminating resistances cannot be chosen
independently and the calculated values have to be used. However, matching sections can be
used to convert to some other terminating resistance as will be discussed in a later part to this
series.
4. References
1. www.simetrix.co.uk An excellent free fully functioning evaluation version of SPICE. The

limitation of this evaluation version is the number of components in the region of 100. This is
rarely a problem.
2. Anatol I. Zverev, Handbook of Filter Synthesis, Wiley Interscience. This book was first
published in 1967 and is regarded as a classic and is quoted as a reference in a great many
articles on filter design. It is now available new in paperback form.
3. Arthur B. Williams and Fred J, Taylor, Electronic Filter Design Handbook, McGraw-Hill.
This is a very good book, much more readable and usable than Zverev, at least for amateur
radio projects.
Richard Harris G3OTK

June 2010
[email protected]
R. J. Harris 2010
Version 1
Page 4

Band Pass Filter Design Part 3. Band Pass Filters From First Principles Richard Harris G3OTK

Uploaded by

Copyright:

Available Formats

Band Pass Filter Design Part 3. Band Pass Filters From First Principles Richard Harris G3OTK

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Band Pass Filter Design Part 3. Band Pass Filters From First Principles Richard Harris G3OTK

Uploaded by

Copyright:

Available Formats

What is Norton's Transform and how can it be used?

How does Norton's Transform replace a capacitor and transformer with just three capacitors?

Band pass filter design

Part 3 - Using Nortons Transform

Third order, capacitor input

Fig. .1. Filter circuit

Fig. 2. Insertion loss

Fig 4. Right hand side of filter

Nortons Theorem enables us to replace C5 and TX1 by three capacitors.

Fig. 6. Replacing C5 and transformer with Nortons Transform capacitors

Fig 7. Filter final circuit diagram

Fig 8. Insertion losses of Fig. 1 and Fig. 7.

1. www.simetrix.co.uk An excellent free fully functioning evaluation version of SPICE. The

Richard Harris G3OTK

You might also like