Interfacing S1 - 568 S1 - 1068 To PowerDB-En - V01

INTERFACE AND REMOTE CONTROL
for S1-568 and S1-1068
Interfacing S1-568 S1-1068 to Power DB v01
Page 1 of 6
Introduction
PowerDB is software used for the collection and reporting of data from maintenance and inspection
activities performed on electrical equipment used in the generation, transmission, and distribution of
electric power.
The software includes interfaces for many test instruments and allows for automated testing and data
acquisition, as well as imports from various file formats. Result and summary reports can be easily
generated.
Three editions of PowerDB are available:
PowerDB Pro
PowerDB Advanced
PowerDB Lite
PowerDB provides a simple and consistent user interface to many Megger instruments including the
DELTA Series Power Factor Test Sets, 3-Phase TTR units, earth testers, 5 kV and 10 kV insulation
resistance testers (IRTs), and many more. PowerDB Lite is bundled with the Meggers MIT and new
S1 ranges.
The new S1 range has remote control capability and a specific application to enable remote control
testing of assets.
Interfacing S1-568 & S1-1068 to PowerDB

The new S1 range has two PC interfaces; a USB device port and a Bluetooth interface. Remote
control is available only via the USB interface.
Connect the instrument to a PC and enable the driver for the S1-568, S1-1068 to be found via the
internet or alternatively, load the version supplied on the product CD if the PC being used has no
access to the internet. The instrument does not need to be powered up to respond to the driver as it
is powered via the USB cable.
Load PowerDB Lite software from the product CD, this may take several minutes. Run up PowerDB
Lite software by clicking the PowerDB Lite icon on your desktop.
Select the S1-568/S1-1068 soft button from
the window entitled, Select An Instrument
to get to the Instrument Configuration
window.
Page 2 of 6
Connecting to the S1 range via Bluetooth is a straight forward process:

1. On the S1 IRT select the left hand test mode switch to
point at the remote control icon and the central switch to
the spanner icon as illustrated.
2. The Bluetooth icon will be visible on the top right of the
IRT display. If the word OFF is flashing, press the up
arrow once and ON will flash. Confirm the setting by
pressing OK.
Bluetooth is now enabled and will be detected by a PC with an activated Bluetooth interface. The
S1 product can be found by exploring devices. The S1 range will identify itself by the model number
and serial number on the PC. The Device Manager soft button in Power DB, Instrument Configuration
Click the Windows Device Manager soft button and verify that a serial port has been allocated to
the instrument:
Expand the Ports section in Device Manager. One serial port should be allocated to Megger
Device (COMxx) where xx is the port number.
If the Bluetooth interface is to be used, expand the ports in Device Manager and ensure that a
Standard Serial over Bluetooth link (COMxx) has been allocated. There will be two ports which
look similar, for example one may be COM6 and the other COM7. The lower number is to be
used for PowerDB Lite.
Ensure that port number xx is allocated correctly
in the Instrument Configuration window, then
click the OK to complete configuration.
Select the required test mode from the Select a

Form window and click OK to continue.
Page 3 of 6
After the form loads, click the zap icon on the toolbar
to initialise the instrument. An OK confirmation
appears at the top of the form if communications have
been successful.
Scroll down the PowerDB form until you see a table with cyan filled headers. RIGHT CLICK once on
one of the cyan coloured areas to activate the S1 remote control application. The cyan filled cells
represent three phases A, B and C.
Remote Control Application

To use the remote control application the remote control safety beacon must be inserted into the 9pin socket found adjacent to the USB port on the right side of the instrument as you look at it. All
manual test functions are available in remote control as well as real-time streaming of test data and a
graphical representation of resistance, voltage or current in the top left window.
For manual control of the S1 click the Import soft button (circled) in the remote control application.
Page 4 of 6
Import/Live Stream Control application enables capture of live streaming data directly by activating
the Start New Live Streaming function. Results are recorded ones a second for the duration of the
test.
Other functions include:
Save Selected To Form save a selected test in top right hand menu to the form in the
table. Typically three tables are available in the PowerDB form representing three phases
named A, B and C. Tests from the Logger can be saved in any form by exiting the logger (Go
Back To Form), right clicking the require phase in the form and selecting to Save Selected
To Form from the logger
Copy Results to Clipboard function facilitates a copy of all data to Excel and other popular
software.
Page 5 of 6
Sample remote control application timed insulation resistance test result shortly
before completion of a 90 s test.
Page 6 of 6

Interfacing S1 - 568 S1 - 1068 To PowerDB-En - V01

Uploaded by

Copyright:

Available Formats

Interfacing S1 - 568 S1 - 1068 To PowerDB-En - V01

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Interfacing S1 - 568 S1 - 1068 To PowerDB-En - V01

Uploaded by

Copyright:

Available Formats

INTERFACE AND REMOTE CONTROL

for S1-568 and S1-1068

Interfacing S1-568 S1-1068 to Power DB v01