Redundancy PDF

ControlLogix
Redundancy
System
1756-CNB/D/E, 1756-CNBR/D/E,
1756-ENBT, 1756-EWEB, 1756-L55,
1756-L55M12, 1756-L55M13,
1756-L55M14, 1756-L55M16,
1756-L55M22, 1756-L55M23,
1756-L55M24, 1756-L61, 1756-L62,
1756-L63, 1757-SRM
User Manual
Important User Information
Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application,
Installation and Maintenance of Solid State Controls (publication SGI-1.1
available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important
differences between solid state equipment and hard-wired electromechanical
devices. Because of this difference, and also because of the wide variety of
uses for solid state equipment, all persons responsible for applying this
equipment must satisfy themselves that each intended application of this
equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for
indirect or consequential damages resulting from the use or application of
this equipment.
The examples and diagrams in this manual are included solely for illustrative
purposes. Because of the many variables and requirements associated with
any particular installation, Rockwell Automation, Inc. cannot assume
responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to
use of information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without
written permission of Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware
of safety considerations.
WARNING
IMPORTANT
ATTENTION
Identifies information about practices or circumstances that can cause

an explosion in a hazardous environment, which may lead to personal
injury or death, property damage, or economic loss.
Identifies information that is critical for successful application and

understanding of the product.
Identifies information about practices or circumstances that can lead
to personal injury or death, property damage, or economic loss.
Attentions help you identify a hazard, avoid a hazard, and recognize
the consequence
SHOCK HAZARD
Labels may be located on or inside the equipment, for example, a drive

or motor, to alert people that dangerous voltage may be present.
BURN HAZARD
Labels may be located on or inside the equipment, for example, a drive

or motor, to alert people that surfaces may be dangerous
temperatures.
Allen-Bradley, RSLogix, RSLogix 5000, RSNetworx, DH+, PanelView, PanelViewPlus, and VersaView are trademarks of Rockwell
Automation, Inc.
RSView and RSLinx are registered trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Summary of Changes
Introduction
This release of this document contains new and updated information.

To find new and updated information, look for change bars, as shown
next to this paragraph.
Updated Information
The document contains the following changes:
Topic
Page
Series E information for 1756-CNB and -CNBR modules
Throughout manual
Redundant System Firmware Combinations
14
Compatible Software Versions
26
Enhancements in Revision 15.56
26
Corrected Anomalies in Revision 15.56
27
Revised Procedure for Setting the Minimum Value for the Watchdog Time
102
Restrictions and Known Anomalies
Appendix E
Update a System That Is Already at Revision 13
142
Store a Project to Nonvolatile Memory While Process Is Running
139
Change CNB Modules from Series D to Series E
131
Publication 1756-UM523F-EN-P - September 2006
Summary of Changes
Notes:
Table of Contents
Chapter 1
ControlLogix Redundancy
Overview
Whats in This Chapter? . . . . . . . . . . . . . . . . . . . . . . . . . . . .

What Are The Main Parts of a Redundant System? . . . . . . . .
What Firmware Combinations Make Up a
Redundant System? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What Are the Important Terms in a Redundant System? . . . .
How Do I Assign the Primary Chassis? . . . . . . . . . . . . . . . . .
What Causes a Switch from One Controller to Another? . . . .
Can I Use a Network Access Port? . . . . . . . . . . . . . . . . . . . .
Do I See a Bump in Outputs During a Switchover?. . . . . . . .
How Does the Second Controller Stay Up to Date? . . . . . . . .
What If I Make Online Edits? . . . . . . . . . . . . . . . . . . . . . . . .
Does My Scan Time Increase? . . . . . . . . . . . . . . . . . . . . . . .
What Happens to Network Addresses During a Switchover? .
If You Have a ControlNet Network. . . . . . . . . . . . . . . . .
If You Have an EtherNet/IP Network . . . . . . . . . . . . . . .
What Cant I Do with a Redundant System? . . . . . . . . . . . . .
Quick Start Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Redundant Chassis Configuration . . . . . . . . . . . . . . . . . .
RSLogix 5000 Project . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Interface Terminals . . . . . . . . . . . . . . . . . . . . .
Compatible Software Versions . . . . . . . . . . . . . . . . . . . . . . .
Enhancements to Redundancy Revision 15.56. . . . . . . . . . . .
Corrected Anomalies in Redundancy Revision 15.56 . . . . . . .
13
13
14
15
15
15
16
16
16
18
18
18
19
20
20
21
21
22
23
25
26
26
27
Chapter 2
Design the System
How to Use This Chapter . . . . . . . . . . . . . . . . . . . . . . .

Lay Out the System . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Place the Pair of Redundant Chassis. . . . . . . . . . . . . . . .
If You Need More Than 100 Meters Between Chassis
Place the I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Place Operator Interface Terminals . . . . . . . . . . . . . . . .
Add Additional Redundant Components. . . . . . . . . . . . .
Redundant ControlNet Media . . . . . . . . . . . . . . . . . .
Redundant Power Supplies. . . . . . . . . . . . . . . . . . . .
Check Connection Requirements . . . . . . . . . . . . . . . . . .
Plan the ControlNet Networks . . . . . . . . . . . . . . . . . . . .
Plan the EtherNet/IP Networks . . . . . . . . . . . . . . . . . . .
Worksheet for IP Swapping . . . . . . . . . . . . . . . . . . .
How an EtherNet/IP Module Handles a Cable Break .
Additional Considerations . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
29
30
32
32
33
34
35
35
36
37
37
40
41
42
43
Chapter 3
Install the System
5
When to Use This Chapter. . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table of Contents
How to Use This Chapter . . . . . . . . . . . . . . . . . .

Preliminary Information. . . . . . . . . . . . . . . . . . . .
Install the Chassis for the Controllers . . . . . . . . . .
Install Modules in the First Redundant Chassis . . .
Install Modules in the Second Redundant Chassis .
Install the Remote Chassis or Rails . . . . . . . . . . . .
Configure the EtherNet/IP Modules . . . . . . . . . . .
Flash the Modules . . . . . . . . . . . . . . . . . . . . . . . .
Check Your Installation . . . . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
45
45
47
48
50
51
52
53
53
53
53
54
Chapter 4
Configure the System Redundancy Purpose of this Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
When to Use this Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Module
How to Use this Chapter . . . . . . . . . . . . . . . . . . . . .
Open the SRM Configuration Tool . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What to Do Next . . . . . . . . . . . . . . . . . . . . . . . .
Check the Revision of Your SRM Configuration Tool
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Check the Version of the Configuration Tool . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set the Clock of the SRM . . . . . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test a Switchover . . . . . . . . . . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Change the Auto-Synchronization Option. . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
55
55
55
55
56
56
57
57
57
58
58
59
59
59
59
60
61
61
61
61
61
63
63
63
63
63
65
65
65
65
Table of Contents
Change the Program Control Option

Purpose. . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
66
66
66
66
67
Chapter 5
Configure and Program the
Controller
When to Use This Chapter. . . . . . . . . . . . . . . . . . . . . . .

How to Use This Chapter . . . . . . . . . . . . . . . . . . . . . . .
Plan for Online Edits . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decide if You Want to Keep Test Edits after
a Switchover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Be Aware That Finalizing Edits Removes
Your Original Logic . . . . . . . . . . . . . . . . . . . . . . . . .
Decide How You Want to Set Aside Unused Memory
Configure a Controller for Redundancy . . . . . . . . . . . . .
Configure Communications . . . . . . . . . . . . . . . . . . . . . .
Configure Produced Tags . . . . . . . . . . . . . . . . . . . .
Configure Message (MSG) Instructions . . . . . . . . . . .
Configure Tags for an HMI . . . . . . . . . . . . . . . . . . . .
Estimate the Crossload Time of a Program . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimize Scan Time . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintain the Integrity of Your Data During a Switchover
Look for Array Shift Instructions . . . . . . . . . . . . . . . .
Look for Scan-Dependent Logic . . . . . . . . . . . . . . . .
Take Preventative Actions . . . . . . . . . . . . . . . . . . . .
Determine the Status of Your Redundancy System . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example 1: Ladder Diagram . . . . . . . . . . . . . . . . . . .
Example 2: Structured Text. . . . . . . . . . . . . . . . . . . .
Check Your Work . . . . . . . . . . . . . . . . . . . . . . . . . .
For More Information. . . . . . . . . . . . . . . . . . . . . . . .
Condition Logic to Run After a Switchover . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example 1: Ladder Diagram . . . . . . . . . . . . . . . . . . .
Example 2: Structured Text. . . . . . . . . . . . . . . . . . . .
Send a Message to the SRM . . . . . . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 69
. . . 69
. . . 69
. . . 70
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
71
71
72
74
74
76
76
77
77
77
77
78
79
85
87
87
88
90
90
90
90
90
90
91
91
91
91
92
92
93
94
94
94
Table of Contents
Before You Begin . . . . . . . . . . . . . . . . . . . .

Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Download the Project to the Primary Controller .
Schedule the ControlNet Networks . . . . . . . . . .
Schedule a New Network . . . . . . . . . . . . . . .
Update the Schedule of an Existing Network.
Check the Keepers. . . . . . . . . . . . . . . . . . . .
Save the Project for Each Controller . . . . . . .
Set the Task Watchdog Times . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
When to Use This Chapter. . . . . . . . . . . . . . . . . . .

How to Use This Chapter . . . . . . . . . . . . . . . . . . .
Find the Cause of a Switchover or Disqualification .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshoot a Failure to Synchronize . . . . . . . . . .
Update a Keeper Signature . . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
See if an Edit Session Is in Progress . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interpret the SRM Event Log . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interpret SRM events . . . . . . . . . . . . . . . . . . . .
Export the SRM Event Log . . . . . . . . . . . . . . . . . . .
Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . .
....................................
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manually Synchronize the Chassis . . . . . . . . . . . . .
Optimize Communication . . . . . . . . . . . . . . . . . . .
Choose a Greater System Overhead Time Slice .
Enter a System Overhead Time Slice. . . . . . . . .
Make All Your Tasks Periodic. . . . . . . . . . . . . .
Check the Allocation of Unused Memory . . . . . . . .
Adjust CNB Usage. . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
95
96
98
98
99
100
100
101
102
Chapter 6
Maintain and Troubleshoot the
System
105
105
106
106
106
106
108
110
110
110
110
110
111
111
111
112
113
113
113
113
114
117
119
119
119
119
120
120
122
123
124
125
126
127
127
Table of Contents
Use RSLinx Software . . . . . . . . . . . . . . . . . . . .

Look at the Four-Character Display. . . . . . . . . .
Send a Message to the CNB Module . . . . . . . . .
Change CNB modules from Series D to Series E . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . .
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Store or Load a Project Using Nonvolatile Memory .
Store a Project to Nonvolatile Memory While a
Process Is Running . . . . . . . . . . . . . . . . . . . . . . . .
Update a Module . . . . . . . . . . . . . . . . . . . . . . . . .
Update a System That Is Already at Revision 13 . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
128
128
130
131
131
132
137
. . . . . . 139
. . . . . . 140
. . . . . . 142
Appendix A
Set Up EtherNet/IP
Communication Across Subnets
Purpose of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . 149

When to Use This Chapter. . . . . . . . . . . . . . . . . . . . . . . . . 149
How to Use This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . 149
Keep an HMI Communicating with the Primary Chassis . . . 150
Install the ControlLogix Redundancy Alias Topic Switcher
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Configure a Driver to Communicate with the Primary and
Secondary EtherNet/IP Modules . . . . . . . . . . . . . . . . . . 152
Create a DDE/OPC Topic for Each Controller . . . . . . . . 153
Create an Alias Topic . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Set Up the Alias Topic Switcher . . . . . . . . . . . . . . . . . . 155
Address the Alias Topic in the HMI Project . . . . . . . . . . 156
Keep a Message Going to the Primary Chassis . . . . . . . . . . 156
Create a Periodic Trigger for the Messages . . . . . . . . . . 157
Get the Redundancy State of Chassis A . . . . . . . . . . . . 158
Get the Redundancy State of Chassis B . . . . . . . . . . . . . 159
Determine Which Chassis is Primary . . . . . . . . . . . . . . . 161
Send the Message to the Appropriate Controller . . . . . . 162
Appendix B
Convert an Existing System to
Redundancy
Introduction . . . . . . . . . . . . . . . . . . . . . . .
Convert Local Modules to Remote Modules
Reconfigure the Local I/O Modules. . . .
Replace Local I/O Tags . . . . . . . . . . . .
Replace Any Aliases to Local I/O Tags .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
165
165
166
166
168
Appendix C
Attributes of the Redundancy
Object
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
10
Table of Contents
Appendix D
If You Have Series B ControlNet
Bridge Modules
About This Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

Communication Loss If You Bridge Through a Series B
ControlNet Bridge Module. . . . . . . . . . . . . . . . . . . . . . . . . 175
Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Prevention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Communication Could Stop If You Use a Series B ControlNet
Bridge Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Corrective Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Prevention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Appendix E
Redundant System Restrictions
Proper Use of an EtherNet/IP Network . . . . . . . . . . . . . . . 181
Preface
Purpose of this Manual
This manual guides the design, development, and implementation of a

redundancy system for a ControlLogix controller.
Who Should Use this

Manual
This manual is intended for those in the following professions who

design and develop applications that use ControlLogix controllers:
When to Use This Manual
Use this manual throughout the lifecycle of a redundancy system. The

lifecycle consists of the following stages:
How to Use this Manual
Software engineers
Control engineers
Application engineers
Instrumentation technicians
Design
Installation
Configuration
Programming
Testing
Maintenance and troubleshooting
This manual is divided into the basic tasks performed during the
design, development, and implementation of a ControlLogix
redundancy system.
Each chapter covers a task.
Tasks are organized in the sequence you will typically perform
them.
In this manual, some text is formatted differently.
Text That Is
Identifies
Italic
The actual name of an item that you Right-click User-Defined

see on your screen or in an example
Right-click on the item that is named

User-Defined.
Courier
Information that you must supply

based on your application (a
variable).
Right-click
name_of_program
You must identify the specific program in

your application. Typically, it is a name or
variable that you have defined.
Press [Enter].
Press the Enter key.
Enclosed in brackets A keyboard key.
11
For Example
Means
Preface
12
Related Documentation
This table lists ControlLogix products and documentation that may be

valuable as in programming an application.
Catalog Number
Title
Publication Number
1756-CNB/D and
1756-CNBR/D
ControlLogix ControlNet Bridge Module Installation Instructions
1756-IN571B
ControlLogix ControlNet Interface Module Release Notes
1756-RN587H
1756-CNB/E and
1756-CNBR/E
ControlLogix ControlNet Bridge Module, Series E Installation Instructions
1756-IN604A
ControlLogix ControlNet Bridge Module, Series E Release Notes
1756-RN627C
1756-ENBT/A
1756 10/100Mbps EtherNet/IP Bridge, Twisted Pair Media Release Notes
1756-RN602A
1756-ENBT
1756-ENBT ControlLogix EtherNet/IP Product Profile
1756-PP004A
ControlLogix EtherNet/IP Bridge Module Installation Instructions
1756-IN019C
ControlLogix EtherNet/IP Communication Release Notes
1756-RN591N
1756-EWEB EtherNet/IP Web Server Module Release Notes
1756-RN604E
EtherNet/IP Web Server Module Installation Instructions
1756-IN588A
EtherNet/IP Web Server Module User Manual
ENET-UM527D
ControlLogix Controller and Memory Board Installation Instructions
1756-IN101K
ControlLogix Controller and Memory Board Installation Instructions
1756-IN101K
ProcessLogix/ControlLogix System Redundancy Module Installation

Instructions
1757-IN092D
1756-EWEB
1756-L55
1756-L61
1756-L62
1756-L63
1756-M12
1756-M13
1756-M14
1756-M16
1756-M22
1756-M23
1756-M24
1757-SRM/B
Chapter
ControlLogix Redundancy Overview
Whats in This Chapter?
What Are The Main Parts of

a Redundant System?
This chapter provides an overview of the ControlLogix redundancy

system, including commonly used terms. It also answers some
common questions about a ControlLogix redundancy system.
Topic
Page
What Are The Main Parts of a Redundant System?
13
What firmware combinations make up a redundant system?
14
How Do I Assign the Primary Chassis?
15
What Causes a Switch from One Controller to Another?
15
Can I Use a Network Access Port?
16
Do I See a Bump in Outputs During a Switchover?
16
How Does the Second Controller Stay Up to Date?
16
What If I Make Online Edits?
18
Does My Scan Time Increase?
18
What Happens to Network Addresses During a Switchover?
18
What Cant I Do with a Redundant System?
20
Quick Start Checklists
21
Compatible Software Versions
26
Enhancements to Redundancy Revision 15.56
26
Corrected Anomalies in Redundancy Revision 15.56
27
The ControlLogix redundancy system uses an identical pair of

ControlLogix chassis to keep a machine or process running if a
problem occurs with a controller.
The following diagram shows the layout of a simple redundant setup.
13
14
Network 1 -
Network 2 - ControlNet network for

I/O communications
EtherNet/IP network or
ControlNet network for HMI
Identical pair of
ControlLogix chassis that
control machine or
process
At least 2 other
ControlNet nodes
Computer that is connected to the

network access port of a remote node
43128
What Firmware
Combinations Make Up a
Redundant System?
The following firmware combinations make up revision 15.56 of the

ControlLogix redundancy system:
Module
Catalog Number
Series
Firmware Revision
ControlLogix5555 controller
1756-L55Mxx
Any
15.56
1756-L61
Any
15.56
1756-L62
Any
15.56
1756-L63
Any
15.56
ControlNet bridge module
1756-CNB
1756-CNBR
7.12
11.1
1756 10/100 Mbps EtherNet/IP Bridge, Twisted Pair Media
1756-ENBT
Any
4.3
1756 10/100 Mbps EtherNet/IP Bridge w/ Enhanced Web Services
1756-EWEB
Any
4.3
Redundancy module
1757-SRM
Any
4.3
What Are the Important

Terms in a Redundant
System?
15
Redundancy requires no additional programming and is transparent to

any devices connected over an EtherNet/IP or ControlNet network.
Redundancy uses 1757-SRM modules to maintain communication
between the pair of redundant chassis.
In a redundant system, the following terms describe the relationship
between the two redundant chassis:
Term
Description
Primary Controller
The controller that is currently controlling the machine or process.
Primary Chassis
The chassis that contains the primary controller or controllers.
Secondary Controller
The controller that is standing by to take control of the machine or process. A secondary
controller always resides in a different chassis than the primary controller.
Secondary Chassis
The chassis that contains the secondary controller or controllers.
Switchover
Transfer of control from the primary controller to the secondary controller. After a
switchover, the controller that takes control becomes the primary controller. Its partner
controller (the controller that was previously the primary controller) becomes the
secondary controller.
How Do I Assign the

Primary Chassis?
In a pair of redundant chassis, the first chassis turned on becomes the

primary chassis. When to the secondary chassis receives power, it
chassis synchronizes itself with the primary chassis.
What Causes a Switch from

One Controller to Another?
When primary chassis components fail, control switches to the

secondary controller. A switchover occurs for any of the following
reasons:
any of the following situations in the primary chassis:
loss of power
major fault of the controller
removal, insertion, or failure of any module in the primary
chassis
break or disconnection of a ControlNet tap or ethernet cable
command from the primary controller
command from RSLinx software
16
Can I Use a Network

Access Port?
To connect a device to the network access port (NAP) of a

1756-CNB/D/E or 1756-CNBR/D/E module, use an NAP that is outside
of a redundant chassis.
IMPORTANT
Use of the Network Access Port (NAP)

Do not connect any device to the network access port (NAP) of
a 1756-CNB/D/E or -CNBR/D/E module in a redundant chassis.
If you connect a device to the NAP of a CNB module in a
redundant chassis, a switchover will fail to occur if the
CNB module is disconnected from the network. While
the CNB module is disconnected from the network, the
controller will be unable to control any I/O devices
through that CNB module.
If you connect a workstation to the NAP of a CNB
module in a redundant chassis, the workstation will be
unable to go online after a switchover.
To connect a device to a ControlNet network via a NAP, use a
NAP that is outside of a redundant chassis.
Do I See a Bump in Outputs

During a Switchover?
Depending on how you organize your RSLogix 5000 project, outputs

may or may not experience a change in state (bump) during a
switchover.
During the switchover, outputs controlled by the highest priority
task experience a bump-free switchover. For example, outputs
dont revert to a previous state.
Outputs in lower priority tasks may experience a change of
state.
The switchover time of a redundant system depends on the type of
failure and the network update time (NUT) of the ControlNet network.
For a NUT of 10 ms, the switchover time is approximately 80 ms to
220 ms.
How Does the Second

Controller Stay Up to Date?
To take over control, the secondary controller requires the same

project as the primary controller. It also requires up-to-date tag values.
17
The following terms describe the process of communication between

the two controllers.
Term
Description
CrossloadC
The transfer of any or all of the contents of the primary

controller to the secondary controller. This could be updated
tag values, force values, online edits, or any other information
about the project. A crossload happens initially when the
chassis synchronize and then repeatedly as the primary
controller executes its logic.
Synchronize
The process that readies a secondary chassis to take over

control if a failure occurs in the primary chassis. During
synchronization, the 1757-SRM modules check that the partner
modules in the redundant chassis pair are compatible with
each other. The SRM modules also provide the path for
crossloading (transferring) the content of the primary controller
to the secondary controller.
Synchronization occurs when power is applied to the secondary
chassis and after a switchover is diagnosed and fixed.
The secondary chassis is ready to assume control if the primary
chassis fails.
Disqualified
The secondary chassis isnt synchronized with the primary

chassis. If a secondary chassis is disqualified, it cant take over
control of the machine or process. A secondary chassis can be
manually disqualified.
Qualify
Same as synchronize
Qualified
Same as synchronized
The 1757-SRM modules keep communication between the primary

and secondary chassis.
Primary chassis
Crossload
1757-SRM modules
43129
Secondary chassis
Synchronized
Dont download the project to the secondary controller. While

the secondary controller is synchronizing with the primary
controller, the 1757-SRM modules automatically let the primary
controller transfer the project to the secondary controller.
Once the secondary controller is synchronized, the 1757-SRM
modules keep the controller synchronized by providing the path
for crossloading any changes that occur in the primary
controller. These changes include:
online edits.
force values.
changes to properties.
changes to data.
results of logic execution.
18
What If I Make Online

Edits?
Online edits automatically crossload to the secondary controller. They

become inactive if a switchover happens before you assemble them
into the project. This stops a mistake from faulting both the old and
new primary controllers.
Suppose you test an online edit and it causes the controller to fault. In
that case, a switchover happens. The new primary controller
automatically untests the edits and goes back to the original code.
You have the option to keep the edits active after a switchover (at the
risk of faulting both controllers).
Does My Scan Time

Increase?
At the end of each program, the primary controller pauses its

execution to crossload the result of any output instruction that
executed in the program. This results in an increased program scan
time for a synchronized redundancy system.
Program Scan Time

Execute program in
primary controller
Start of program
What Happens to Network

Addresses During a
Switchover?
Crossload results to
secondary controller
End of program
Each CNB, ENBT, or EWEB module in a redundant chassis shares a

pair of network addresses with its partner in the other chassis.
19
If You Have a ControlNet Network
1 2 3
0
4
7 6 5
1 2 3
0
4
7 6 5
Set each pair of CNB modules to

the same node number.
Primary
chassis
Secondary
chassis
24
25
CNB modules in the primary chassis
use the node number to which they
are set.
1 2 3
0
4
7 6 5
CNB modules swap node numbers.

Switchover
1 2 3
0
4
7 6 5
Secondary
chassis
25
Primary
chassis
24
CNB modules in the secondary chassis use the
node number to which they are set PLUS 1.
CNB modules swap node numbers.
Workstations and HMIs continue to connect

to the same node number.
Workstations and HMIs continue to connect

to the same node number.
20
If You Have an EtherNet/IP Network

Set both EtherNet/IP modules to
the SAME IP address
Port Configuration
Primary
chassis
Port Configuration
Secondary
chassis
E
N
B
T
E
N
B
T
10.10.10.10
10.10.10.11
An EtherNet/IP module in the primary

chassis uses the IP address to which
it is set.
An EtherNet/IP module in the

secondary chassis uses the IP address
to which it is set + 1 in the last address
segment.
Switchover
EtherNet/IP modules
Secondary
chassis
Primary
chassis
E
N
B
T
10.10.10.11
What Cant I Do with a

Redundant System?
E
N
B
T
10.10.10.10
Dont use any of these features in a ControlLogix redundancy system:
local chassis I/O, 1756-DHRIO, or 1756-DNB modules

event task
inhibit a task
data storage on a CompactFlash card via the controller. Its OK
to store a project on a CompactFlash card. See page 137.
motion control, such as the following modules:
1756-HYD02
Quick Start Checklists
21
1756-L60M03SE
1756-M02AE
1756-M02AS
1756-M03SE
1756-M08SE
1756-M16SE
The following checklists provide a summary of the criteria for a

successful ControlLogix redundancy system. See the remaining
chapters for more information on each parameter.
System Layout
Parameter
1. ControlNet networks
Criteria
Page
ControlNet networks are the primary networks for the system.
30, 33
OK to bridge to devices on other networks, such as DeviceNet, Universal Remote I/O,

and DH+ networks.
Networks follow the guidelines in Logix5000 Controllers Design Considerations,
publication 1756-RM094.
2. I/O Placement
All I/O modules in remote chassis or DIN rails (no I/O in the local chassis)
30, 33
All I/O in ONLY the following locations:

same ControlNet network as the redundant controllers (no bridging)
DeviceNet network (via a 1756-DNB module in a remote chassis)
universal remote I/O network (via a 1756-DHRIO module in a remote chassis)
3. ControlNet network update
times
NUTs 90 ms
37
NUTs specified relationship to each other
4. Number of ControlNet nodes At least 2 nodes on each network in addition to the CNBs in the redundant chassis - For
example, each ControlNet network has at least 4 nodes.
5. ControlNet node
assignments
Nonredundant nodes use the lowest node numbers
37
18, 37
CNB modules in the redundant chassis set close to the SMAX.

2 consecutive node addresses for each set of partner CNB modules (one in each
chassis)
Switches of each partner CNB module set to the same node address
6. Network Access Ports
No devices connected to the network access ports of CNB modules in the redundant
chassis
30
7. EtherNet/IP networks
EtherNet/IP networks are only for HMIs, workstations, and messaging (no control of I/O). 30, 40
No EtherNet/IP network for:
control of I/O
peer interlocking (produced and consumed tags)
22
Redundant Chassis Configuration

Parameter
Criteria
Page
1. Chassis size
Same size chassis for each pair of redundant chassis.
31
2. Chassis layout
Only the following modules in each redundant chassis (NO other modules):
31
controllers
ControlNet modules
EtherNet/IP modules
System redundancy module (needs 2 slots)
Each chassis within a redundant pair looks the same:
Identical modules (same catalog number, series, revision, and memory size)
Same slot assignments
3. System redundancy
modules
1757-SRM module:
31, 32
1 in each redundant chassis

Needs 2 slots
Needs 1757-SRCx cable (1, 3, 10, 50, and 100 meter lengths)
4. Controllers
ControlLogix5555, ControlLogix5561, ControlLogix5562, or ControlLogix5563 controllers
31
Which type of controller do you want to use?

If ControlLogix5555, then 1 or 2 controllers in EACH redundant chassis.
If ControlLogix5561, ControlLogix5562, or ControlLogix5563, then ONLY 1 controller in
each redundant chassis.
Same type of controller throughout the chassis.
Enough memory for 2 copies of all data.
7 connections for redundancy
5. ControlNet modules
1756-CNB/D/E or 1756-CNBR/D/E module or modules:

CPU usage 75%
CNB modules have the same keeper information
5 CNB modules. See also parameter 6 below.
31, 110,
127
23
Redundant Chassis Configuration (Continued)

Parameter
Criteria
Page
6. EtherNet/IP modules
1756-ENBT or 1756-EWEB modules:
31, 40
Which modules do you want to use?

If 1756-ENBT, catalog revision greater than or equal to E01 (E01, E02, , F01). See the
label on the side of the module or its box.
If 1756-EWEB, any catalog revision
Up to 2 EtherNet/IP modules in each redundant chassis, within these limits:
If you have
Use up to
1 ControlNet module
2 EtherNet/IP modules
2 ControlNet modules
1 EtherNet/IP module
No EtherNet/IP modules
Dont use more than 5 ControlNet

modules.
RSLogix 5000 Project

Parameter
Criteria
Page
1. Number of projects
Only one RSLogix 5000 project for the pair of redundant controllers. The project automatically
crossloads to the secondary controller when the secondary controller synchronizes with the
primary controller.
69
2. Controller properties
ControlLogix5555, ControlLogix5561, ControlLogix5562, or ControlLogix5563 controller
72
Redundancy enabled
3. Task structure
Only one task at the highest priority
74, 79,
123
If more than one task, all tasks periodic

4. I/O
Outputs that require a bumpless switchover are in the highest priority task
74
Requested packet interval (RPI) less than or equal to 375 milliseconds. (Larger RPIs may
produce a bump at switchover.).
5. Task watchdog time
Watchdog time (2 * maximum_scan_time) + 100 ms
102
where:
Maximum_scan_time is the maximum scan time for the entire task when the secondary
controller is synchronized.
24
RSLogix 5000 Project (Continued)

Parameter
6. Minimizing scan time
Criteria
A few large programs instead of a lot of small programs
Page
79
No unused tags
Arrays and user-defined data types instead of individual tags
User-defined data types as compact as possible
Code as compact as possible
Code runs only when you need it
Data grouped by how often you need it
DINT tags instead of SINT or INT tags
7. Data integrity
Special treatment for:
85
Bit Shift Left (BSL) and Bit Shift Right (BSR) instructions
FIFO Unload (FFU) instructions
Logic that is scan dependent
8. Produced and
consumed tags
If you want a controller in another chassis to consume a tag from the redundant controller, use
a comm format of None. In the I/O configuration of the consuming controller, select a comm
format of None for the remote CNB module (the CNB that is physically in the redundant
chassis).
74
9. Message (MSG)
instructions
For any MSG instruction from a controller in another chassis to a redundant controller, cache
the connection.
74
25
Operator Interface Terminals

Parameter
For any of these operator interfaces
Criteria
Page
1. EtherNet/IP network
PanelView Standard terminal
Same as a nonredundant system
30, 34, 40
PanelView Plus terminal

VersaView industrial computer running a
Windows CE operating system
RSView Supervisory Edition software with

RSLinx Enterprise software
Use RSLinx Enterprise software revision

3.0 or later.
Set aside connections for EACH PanelView
Plus or VersaView CE terminal:
In this module
Set aside
controller
5 connections
CNB
5 connections
ENBT
5 connections
EWEB
5 connections
Use RSLinx Enterprise software revision

3.0 or later.
Use IP swapping.
Keep the HMI and both redundant chassis
on the same subnet.

RSLinx 2.x software
Limit the number of RSLinx servers that a

controller uses to 1 (ideal) to 3 (maximum).
RSView 32 software
Any other HMI client software that uses
RSLinx 2.x software
2. ControlNet network

PanelView 1000e/1400e terminal
Do terminals use unscheduled

communication?
30, 34, 37
Yes Use 4 terminals per controller.

No Use the number of terminals that
you need.
RSView Supervisory Edition software

RSView 32 software
Set aside connections for EACH PanelView

Plus or VersaView CE terminal:
In this module
Set aside
controller
5 connections
CNB
5 connections
Limit the number of RSLinx servers that a

controller uses to 1 (ideal) to 3 (maximum).

RSLinx 2.x software
26
Compatible Software
Versions
With version 15.56 of the ControlLogix redundancy system, use any of

the following software versions:
For This Software
Use This Version
RSLinx
2.50
1757-SRM System Redundancy

Module Configuration tool
3.4
Notes
Important: Dont update the SRM Configuration tool at this time. See
Update a System That Is Already at Revision 13 on page 142.
Get Knowledgebase document G92234770. To access Rockwell
Automations Knowledgebase, go to
http://support.rockwellautomation.com
RSLinx Enterprise
3.0
You need this only for these HMIs:

VersaView industrial computer running a Windows CE operating system
Important: For RSView Supervisory Edition software, install the RSLinx
Enterprise HOTFIX. The HOTFIX improves the EtherNet/IP switchover time.
See Knowledgebase document R154640079. To access Rockwell
Automations Knowledgebase, go to
RSLogix 5000
15.01
RSNetWorx
5.11
Enhancements to
Redundancy Revision 15.56
The following enhancements apply to a redundant system using

revision 15.56:
Enhancement
Description
Update the firmware of

the redundant chassis
while the process is
running
This revision lets you update the firmware in the redundant

chassis without shutting down the process. To do this, the
system must be at revision 13.
Add I/O modules while

online
At runtime, add 1756 I/O modules to a remote chassis via the

unscheduled portion of a ControlNet network.
Corrected Anomalies in
Redundancy Revision 15.56
27
Redundancy revision 15.56 corrects the following anomalies:
Corrected Anomaly
Description
The File Search Compare (FSC)

instruction caused an unrecoverable
fault
The FSC instruction caused a unrecoverable fault if both these conditions occurred:
major fault declared from within the expression of an FSC instruction
fault cleared by user fault routine
Lgx00055522
You couldnt send an SLC typed write

message to a redundant controller
An SLC-typed write message to a redundant controller produced error F007.

Lgx00058402
Memory changes during prescan

werent always crossloaded
Sometimes the primary controller didnt send data changes that it made during prescan to the
Lgx00060517
Some data table write services

Data table write, big write, and read-modify-write services werent immediately forwarded to the
werent immediately forwarded to the secondary controller if the service used a symbolic address. Instead, they were forwarded after
the next program scan.
Lgx00060643
A secondary SRM faulted with an
E888 error if you unplugged a CNB
module
The secondary 1757-SRM module sometimes faulted while synchronized if you unplugged the tap
to a secondary 1756-CNB module. The error code of the SRM module was E888. This caused the
chassis to become disqualified.
You had to remove and reinsert the secondary SRM module under power to recover.
Lgx00060989
A synchronized chassis pair didnt

The redundant chassis pair didnt automatically synchronize after multiple cycles of
automatically synchronize after being disqualification caused by either unplugging the tap to a secondary 1756-CNB module or
disqualified
power-cycling the secondary chassis.
Lgx00061808, Lgx00060991
Sometimes a module faulted after a
switchover
Sometimes a module would fault after a broken or disconnected communication cable caused a
switchover. The module showed a fault code of 16#0022.
Lgx00061990
The SRM pair lost the fiber optic

connection under heavy HMI traffic
The synchronized pair of 1757-SRM modules would sometimes lose their connection across the
fiber optic link under heavy HMI traffic conditions. This caused the secondary chassis to become
disqualified either with the SRM modules showing no partner or the secondary module showing
error EA91
Lgx00062847, Lgx00062839, Lgx00062171
28
Corrected Anomaly
Description
The primary SRM module rejected a

synchronization command
The primary 1757-SRM module rejected a synchronization command when:

the auto-qualification option was set to Never
and
the synchronization command was given within 30 seconds after disqualification of the
redundant chassis pair.
The SRM module continued to reject any synchronization command. You had to change the
auto-qualification option to Always to synchronize the chassis.
Lgx00062954, Lgx00058896, Lgx00037660
ENBT module wouldnt reply to a ping Sometimes you wouldnt get a reply when you pinged a 1756-ENBT module.
Lgx00062979
Updating a primary SRM module
caused an unrecoverable fault
Updating the firmware of a 1757-SRM module in a primary chassis sometimes caused an

recoverable fault in the controller. This happened if the controller ran out of outgoing unconnected
buffers.
Lgx00063005
CompactFlash image caused a major

fault
A controller had a major fault if you:

stored a CompactFlash image using a controller that was last powered down as a disqualified
and
configured the image to go to run mode after loading.
Lgx00063515
You couldnt download to a

disqualified secondary controller
without enough memory reserved for
logic
You couldnt download to a

disqualified secondary controller
if the slider was too close to Tags.
Lgx00063587
Chapter
Design the System
Use this chapter to design a redundancy system for a ControlLogix

controller
How to Use This Chapter
29
To design your system, complete the following tasks:

Topic
Page
Lay Out the System
30
Place the Pair of Redundant Chassis
32
Place the I/O
33
Place Operator Interface Terminals
34
Add Additional Redundant Components
35
Check Connection Requirements
37
Plan the ControlNet Networks
37
Plan the EtherNet/IP Networks
40
Additional Considerations
43
30
Design the System
Lay Out the System
ControlLogix Redundancy Requirements and Recommendations
Use separate networks for unscheduled and scheduled

communication
Unscheduled Communication
EtherNet/IP
or
ControlNet
For unscheduled communication (HMI, workstations,

message instructions), use either an EtherNet/IP or a
ControlNet network.
For scheduled communications (I/O, produced/consumed
tags), use a ControlNet network.
Scheduled Communication
ControlNet
For unscheduled communication,

use 4 PanelView terminals per
controller.
ControlNet network:
Set NUT 90 ms
Multiple redundant chassis

pairs are OK.
Set RPIs 375 ms

If multiple ControlNet
networks, set NUTs
specified values.
Remote location for all:

I/O
DNB, DHRIO, & MVI
communication modules
Assign the lowest node numbers
to nonredundant nodes.
C
N
B
I/O modules
E D D M
N N H V
B B R I
I
O
To connect a computer to the

network via an NAP, use a remote
node.
Other networks
At least 2 nodes in
addition to the CNBs in
the redundant chassis
An additional node can be:

a second CNB module in the same remote chassis or in a different remote chassis
any other ControlNet device (not required to be keeper capable)
Design the System
31
ControlLogix Redundancy Requirements and Recommendations (Continued)

1756-ENBT or 1756-EWEB modules:
1756-CNB/D/E or 1756-CNBR/D/E module or modules:
1- 2 in each redundant chassis

5 total communication modules (CNBs and ENBTs) in each
redundant chassis
1-5 in each redundant chassis

5 total communication modules (CNBs, ENBTs, and
EWEBs) in each redundant chassis
For 1756-ENBT modules, catalog revision must be greater than

or equal to E01 (E01, E02, , F01). See the side of the module
or its box.
Keep CPU usage 75%,

Allocate 2 consecutive node addresses for each set of
partner CNB modules (one in each chassis).
Requires RSLinx software, version 2.41.00 (Build 10.6) or later.
Assign each partner CNB module to the same node

address.
ControlLogix5555, ControlLogix5561, ControlLogix5562, or

ControlLogix5563 controllers:
Assign the higher node addresses in the system to the

CNB modules in the redundant chassis.
Same type of controller throughout the chassis.

If ControlLogix5555, then 1 or 2 controllers in EACH
redundant chassis.
If ControlLogix5561, ControlLogix5562, or
ControlLogix5563, then only 1 controller in EACH
redundant chassis.
1757-SRM module:
Enough memory for 2 copies of all data.
Only 1 in each redundant chassis
7 connections for redundancy
uses 2 slots
Redundant
Chassis A
E C
N N
B B
T
S
R
M
No other modules
Identical modules:
Same size of chassis
Same slot number

Same catalog number, series, and revision
Same memory size (controller)
Redundant
Chassis B
E C
N N
B B
T
S
R
M
No other modules
1757-SRCx cable
1, 3, 10, 50, and
100 meter lengths
32
Design the System
Place the Pair of Redundant

Chassis
Redundant
Chassis A
With the standard redundancy module cables, a pair of redundant

chassis (primary and secondary) can function up to 100 meters apart.
E C
N N
B B
T
S
R
M
No other modules
Redundancy Module Cable:

1757-SRC1 cable (1 meter)
1757-SRC3 cable (3 meters)
Redundant
Chassis B
E C
N N
B B
T
S
R
M
No other modules
If You Need More Than 100 Meters Between Chassis

To place the primary and secondary controller chassis more than 100
meters apart, use a custom fiber optic cable. For a custom cable,
follow these rules:
1. Keep total light loss through the cable less than or equal to 7dB.
2. Keep total length less than or equal to 4 km.
3. Use high quality 62.5/125 micron multi-mode fiber-optic cable.
4. Use professionally installed SC-style connectors to connect to
the 1757-SRM modules.
Design the System
Place the I/O
33
In a ControlLogix redundancy system, place all I/O in ONLY the

following locations:
Same ControlNet network as the redundant controllers (no
bridging to I/O modules on another ControlNet network)
DeviceNet network
Universal remote I/O network
Redundant chassis pair
ControlNet network
C
N I/O modules
B
D D
H N
R B
I
C E
N N
B B
Remote chassis
I/O No
EtherNet/IP network
HMI Yes
I/O No
ControlNet network
HMI Yes
I/O Yes
DeviceNet network
HMI Yes
I/O Yes
Universal remote I/O network
HMI Yes
34
Design the System
Place Operator Interface

Terminals
For operator interface terminals, stay within these limitations:
For this network
And any of these operator interfaces
Follow these guidelines
EtherNet/IP network
Same as a nonredundant system

RSView Supervisory Edition software with RSLinx

Enterprise software
Use RSLinx Enterprise software revision 3.0 or

later.
Set aside connections for each PanelView Plus or
VersaView CE terminal:
In this module
Set aside
controller
5 connections
CNB
5 connections
ENBT
5 connections
EWEB
5 connections
Use RSLinx Enterprise software revision 3.0 or

later.
Use IP swapping.
Keep the HMI and both redundant chassis on the
same subnet.

RSLinx 2.x software
Limit the number of RSLinx servers that a controller

uses to 1 (ideal) to 3 (maximum).
RSView 32 software
RSLinx 2.x software
ControlNet network

PanelView 1000e/1400e terminal
Do your terminals use unscheduled communication?

Yes Use 4 terminals per controller.
No Use the number of terminals that you need.


RSView 32 software
RSLinx 2.x software
Set aside connections for each PanelView Plus or

VersaView CE terminal:
In this module
Set aside
controller
5 connections
CNB
5 connections
Limit the number of RSLinx servers that a controller

uses to 1 (ideal) to 3 (maximum).
Design the System
Add Additional Redundant

Components
35
In addition to using redundant pairs of controllers, you may also add

the following redundant components to your system:
Redundant ControlNet Media
Redundant Power Supplies
Redundant ControlNet Media

Redundant ControlNet media prevents a loss of communication if a
trunkline or tap is severed or disconnected. It uses the following
components:
1756-CNBR ControlNet modules
Two identical ControlNet links
ControlLogix chassis with

1756-CNBR module
ControlNet node
Redundant media
ControlNet node
36
Design the System
Redundant Power Supplies

Redundant power supplies let you maintain power to a ControlLogix
chassis if a power supply fails. Redundant power supplies use the
following hardware:
Two redundant power supplies, any combination of 1756-PA75R
and 1756-PB75R
1756-PSCA chassis adapter module, in place of the standard
power supply
Two 1756-CPR cables to connect the power supplies to the
1756-PSCA adapter
User-supplied annunciator wiring to connect the power supplies
to the input modules if needed
1756-PA75R or
1756-PB75R
1756-CPR cable
ControlLogix chassis with

1756-PSCA module
1756-PA75R or
1756-PB75R
Annunciator wiring
1756 digital
input module
Design the System
Check Connection
Requirements
37
Set aside seven connections in each redundant controller for

redundancy communication:
Two connections for the SRM
Five connections for the partner controller
Plan the ControlNet

Networks
Follow these guidelines to plan a ControlNet networks:
Guideline
Details
1. Make sure the network has at least 2 nodes plus the

redundant chassis pair.
An additional node can be:

a second CNB module in the same remote chassis or in a different remote
chassis
any other ControlNet device
a workstation that is running RSLinx software.
If your ControlNet network contains only one node other than the redundant
chassis pair, that node will drop its connections during a switchover. This may
cause the outputs of that node to change state during the switchover.
2. Give the lowest ControlNet addresses to I/O chassis

and other remote chassis.
Dont give the lowest addresses to the redundant chassis pair.

If you give the lowest address to a CNB module in the redundant chassis pair:
on a switchover, you may temporarily lose communication with I/O
modules, produced tags, and consumed tags.
If you remove the CNB module from the primary chassis while chassis
power is on, you may temporarily lose communication with I/O modules,
produced tags, and consumed tags.
If every ControlNet node powers down at the same time (for example, a
plant-wide power loss), you may have to cycle the power to the primary
chassis to restore communication.
38
Design the System
Guideline
Details
3. Set aside 2 consecutive ControlNet addresses for

each pair of redundant chassis (for example, nodes 3
and 4).
If each redundant chassis has multiple CNB modules, set aside a pair of
node numbers for each pair of CNB modules (one in each chassis).
Do not configure any other device on the ControlNet network for either of
these addresses. For example, if you allocated nodes 3 and 4 for the
redundant chassis, then no other device should use those node numbers.
Pair of CNB modules (one in each

redundant chassis)
Slot and node numbers

Slot #
Primary node #
Secondary node #
(primary node # + 1)
1st pair of CNB modules

2nd pair of CNB modules
3rd pair of CNB modules
4th pair of CNB modules
5th pair of CNB modules
4. Know that the switchover time depends on the NUT of Use the network update time (NUT) of the ControlNet network to estimate
the ControlNet network.
how long it takes your system to switchover:
If
And the NUT is
Then the switchover time is
The chassis loses power or

a module fails
6 ms or less
60 ms
7 ms or more
5 (NUT ) + MAX (2 (NUT ), 30)
A CNB module cant

communicate with any
other node
14 (NUT ) + MAX (2 (NUT ), 30) + 50
Example 1
The chassis loses power and the NUT = 4 ms. In that case, the switchover
time is approximately 60 ms.
Example 2
The chassis loses power and the NUT = 10 ms. In that case, the switchover
time is approximately 80 ms.
Example 3
You unplug the CNB from the network and the NUT = 10 ms. In that case, the
switchover time is approximately 220 ms.
5. Use a NUT that is less than or equal to 90 ms.
If you use a larger network update time (NUT), the controller could lose its
connection with a module during a switchover. This could cause outputs to
change state.
Design the System
Guideline
Details
6. Do the redundant chassis use more than 1 ControlNet

network?
Yes See page 31.
The NUT of each network must be within the values indicated on page 31. If
you use a larger network update time (NUT), the controller could lose its
connection with a module during a switchover. This could cause outputs to
change state.
No Skip this guideline.
Example
If the NUT of this network is 5 ms
39
Then the NUT of this network must be

21 ms or less.
ControlNet
network 1
ControlNet
network 2
If the smallest
NUT on a network
is (ms):
Then the largest NUT on any other

network must be less than or equal
to (ms):
If the smallest
NUT on a network
is (ms):
Then the largest NUT on any other

network must be less than or equal
to (ms):
15
21
55
17
22
57
19
23
59
21
24
62
23
25
64
25
26
66
27
27
68
29
28
71
10
31
29
73
11
33
30
75
12
35
31
78
13
37
32
80
14
39
33
82
15
41
34
84
16
43
35
87
17
46
36
89
18
48
37 - 90
90
19
50
20
52
40
Design the System
Plan the EtherNet/IP

Networks
Follow these guidelines as you plan your EtherNet/IP networks:
Guideline
Details
1. Use EtherNet/IP ONLY for HMIs, workstations, and

messaging.
In a redundant system, use an EtherNet/IP network only for HMI, workstation,

and message communication. Do not use an EtherNet/IP network for:
control of I/O modules.
peer interlocking (produced and consumed tags).
Important: RSLogix 5000 software lets you set up and download a project
that tries to use an EtherNet/IP network for I/O, produced tags, or consumed
tags. Those communications dont work however.
2. Are communication delays OK during a switchover?

If Yes, then continue with EtherNet/IP.
If No, then use ControlNet.
Communication stops over an EtherNet/IP network with your controllers and

HMIs during a switchover.
You wont be able to communicate with them for up to a minute.
The actual delay depends on your network topology.
If you need bumpless communication, use a ControlNet network.
3. If you need a redundant network, use ControlNet.
2 EtherNet/IP modules in same chassis doesnt give you redundant

EtherNet/IP communication. A switchover still happens if one of the modules
fails or a cable breaks.
See How an EtherNet/IP Module Handles a Cable Break on page 42.
4. Make sure that your ENBT modules are catalog

revision E01 or later.
ControlLog
Ethernet/IP 10/100
CAT. NO./SERIES
CAT. REV.
1756-ENBT
E01
To use a 1756-ENBT module in a redundant controller chassis, make sure the

catalog revision of the module is greater than or equal to E01 (E01, E02, ,
F01).
To find the catalog revision, look at the label on the side of the module or
box.
If you use an older ENBT module, your secondary chassis wont
synchronize.
Catalog revision
Design the System
Guideline
41
Details
5. Decide how to handle IP addresses.
If BOTH redundant chassis are on Then

Use IP swapping.
Same subnet
During a switchover the primary and

secondary modules swap IP
addresses. This lets you use the same
IP address regardless of which
chassis is primary.
Switch
Primary
chassis
Secondary
chassis
See the next guideline for details.

You MUST change to the new primary
address after a switchover. Use
ControlLogix Redundancy Alias Topic
Switcher software to do this. See
Appendix A.
Different subnets
Router
Switch
Switch
Primary
chassis
6. If youre using IP swapping, give the same IP

address to the primary module and its partner.
Secondary
chassis
A. Give the SAME IP address, subnet mask, and gateway address to BOTH
modules in the redundant pair.
B. Leave the next highest IP address open for the secondary module.
For example
Set the primary and secondary
modules to
10.10.10.10
Leave this open for the secondary
10.10.10.11
The module in the secondary chassis automatically uses the IP address of the
primary + 1.
Worksheet for IP Swapping

Pair of ENBT or EWEB modules
(one in each redundant chassis)
Slot #
Configuration
Primary
IP address
Secondary IP address
(primary address + 1)
Subnet mask
Gateway address
1st pair of ENBT or EWEB modules

2nd pair of ENBT or EWEB modules
42
Design the System
How an EtherNet/IP Module Handles a Cable Break

An EtherNet/IP module looks for a carrier signal only from the closest
switch. It doesnt know the health of the network beyond that point.
Data doesnt have to be flowing.
If the EtherNet/IP module:
gets the carrier signal, it considers the network as OK.
doesnt get the carrier signal, it shows Link lost.
One switch
One subnet
/LQNORVW
/LQNORVW
Several switches
Several subnets
C
ZRQWVZLWFKRYHU
ZRQWVZLWFKRYHURUGLVTXDOLI\WKH
VHFRQGDU\FKDVVLV
ZLOOV\QFKURQL]H
ZLOOV\QFKURQL]H
+0,FDQWFRPPXQLFDWHZLWK
SULPDU\FKDVVLV
+0,ZRQWEHDEOHWRFRPPXQLFDWH
ZLWKWKLVFKDVVLVLILWEHFRPHVSULPDU\
VZLWFK
6XEQHW%
6XEQHW$
URXWHU
ZLOOVZLWFKRYHU
ZRQWV\QFKURQL]H
ZLOOGLVTXDOLI\
VZLWFK
VZLWFK
(WKHU1HW,3PRGXOH
VKRZV/LQNORVW
(WKHU1HW,3PRGXOH
VKRZV/LQNORVW
SULPDU\FKDVVLV
ZRQWV\QFKURQL]H
VHFRQGDU\FKDVVLV
Design the System
43
Additional Considerations
Switchover Always Triggers an Event
Task in a Remote, Nonredundant
Controller
A switchover triggers an event task under the following combination of circumstances:

The event task is in a nonredundant controller. An Event task is not permitted in a redundant
controller.
A redundant controller triggers the event task via a produced tag.
This occurs regardless of how you configure the produced tag.
Both configurations always trigger an

event task during a switchover.
Simultaneous Branch Delays the

Execution of a Higher Priority Task
In an SFC, each path of a simultaneous branch delays
the execution of a higher priority task by up to 25 s.
44
Design the System
Notes:
Chapter
Install the System
When to Use This Chapter
Use this chapter to install the hardware of a ControlLogix redundancy

system.
To install the system, complete the following tasks:

Topic
Page
Review the Preliminary Information
45
Install the Chassis for the Controllers
47
Install Modules in the First Redundant Chassis
48
Install Modules in the Second Redundant Chassis
50
Install the Remote Chassis or Rails
51
Configure the EtherNet/IP Modules
52
Flash the Modules
53
Check Your Installation
53
Preliminary Information
IMPORTANT
Use of the Network Access Port (NAP)

Do not connect any device to the network access port (NAP) of
a 1756-CNB/D/E or 1756-CNBR/D/E module in a redundant
chassis.
If you connect a device to the NAP of a CNB module in a
redundant chassis, a switchover will fail to occur if the CNB
module is disconnected from the network. While the CNB
module is disconnected from the network, the controller
will be unable to control any I/O devices through that CNB
module.
If you connect a workstation to the NAP of a CNB module in
a redundant chassis, the workstation will be unable to go
online after a switchover.
To connect a device to a ControlNet network via a NAP, use a
NAP that is outside of a redundant chassis.
45
46
Install the System
This chapter provides the sequence of tasks and the critical actions for
the successful installation of a ControlLogix redundancy system. It
does not replace the installation instructions for the components of
the system. During installation, refer to the following publications:
Install this component
According to this publication
1756-A4, -A7, -A10, -A13, or -A17 chassis
ControlLogix Chassis Installation Instructions, publication 1756-IN080
1756-PA72 or -PB72 power supply
ControlLogix Power Supplies Installation Instructions, publication 1756-5.67
1756-PA75 or -PB75 power supply
ControlLogix Power Supplies Installation Instructions, publication 1756-5.78
ControlLogix controller
ControlLogix Controller and Memory Board Installation Instructions, publication

1756-IN101
1756-CNB/D/E or -CNBR/D/E module
ControlLogix ControlNet Bridge Installation Instructions, publication 1756-IN571
1756-ENBT module
ControlLogix EtherNet/IP Bridge Module Installation Instructions, publication

1756-IN019
1756-EWEB module
EtherNet/IP Web Server Module Installation Instructions, publication 1756-IN588
1757-SRM module
ProcessLogix/ControlLogix System Redundancy Module Installation Instructions,

publication 1757-IN092
Installation instructions provide important information, such as

detailed installation steps, safety considerations, enclosure
requirements, and hazardous location information.
Before installing the system, review the following guidelines for safe
handling of ControlLogix components:
WARNING
When you insert or remove a module while backplane power is

on, an electrical arc can occur. This could cause an explosion in
hazardous location installations. Be sure that power is removed
or the area is nonhazardous before proceeding.
Repeated electrical arcing causes excessive wear to contacts on both a

module and its mating connector. Worn contacts may create electrical
resistance that can affect module operation.
Install the System
ATTENTION
47
Preventing Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which
can cause internal damage and affect normal operation. Follow
these guidelines when you handle this equipment:
Touch a grounded object to discharge potential static.

Wear an approved grounding wriststrap.
Do not touch connectors or pins on component boards.
Do not touch circuit components inside the equipment.
If available, use a static-safe workstation.
When not in use, store the equipment in appropriate
static-safe packaging.
Install the Chassis for the

Controllers
1.
42798
2.
1. Install the two ControlLogix chassis (redundant) that will contain

the controllers.
Place the chassis within the length of a 1757-SRCx cable.
Install each chassis according to the ControlLogix Chassis
Installation Instructions, publication 1756-IN080.
If you are converting an existing system that contains local
I/O modules, you still need two additional chassis. In a
redundant system, you must place all I/O modules outside
the redundant chassis pair.
48
Install the System
2. For each chassis, install a ControlLogix power supply according

to the corresponding installation instructions:
Install this power supply
According to this publication
1756-PA72
ControlLogix Power Supplies Installation Instructions,

publication 1756-IN078B
1756-PB72
1756-PA75R
1756-PB75R
Install Modules in the First

Redundant Chassis
IMPORTANT
ControlLogix Redundant Power Supply Installation

Instructions, publication 1756-IN573C
Set the rotary switches of the 1756-CNB/D/E or

1756-CNBR/D/E modules for both redundant chassis to the
same node address.
1. Set the rotary switches of each of the 1756-CNB/D/E or

1756-CNBR/D/E modules to the primary node number plus one.
42796
2.
For example, nodes 3 and 4 have a primary node number of 2.

If you allocate nodes 3 and 4 for the redundant chassis, set both
CNB modules to node 3.
This is only an example. You can install the

module in any slot.
C
N
B
3.
42799
2. Install a 1756-CNB/D/E or 1756-CNBR/D/E module. See

ControlLogix ControlNet Bridge Installation Instructions,
publication 1756-IN571.
Install the System
WARNING
49
If you connect or disconnect the communications cable with

power applied to this module or any device on the network, an
electrical arc can occur. This could cause an explosion in
hazardous location installations.
Be sure that power is removed or the area is nonhazardous
before proceeding.
3. Connect the CNB module to the ControlNet network.

4.
5.
L C E
5 N N
5 B B
T
6.
This is only an example. You can install the

modules in any slot.
S
R
M
42799
4. Install the controller or controllers. See ControlLogix Controller

and Memory Board Installation Instructions, publication
1756-IN101.
5. Install the 1756-ENBT or 1756-EWEB module or modules (2
max.), if required. Connect each module to an ethernet switch.
6. Install the 1757-SRM module. See ProcessLogix/ControlLogix
System Redundancy Module Installation Instructions,
publication 1757-IN092.
50
Install the System
Install Modules in the

Second Redundant Chassis
1.
L C E
5 N N
5 B B
T
S
R
M
L C E
5 N N
5 B B
T
S
R
M
2.
42800
3.
IMPORTANT
The modules in each redundant chassis must match each other

slot-by-slot.
Set the rotary switches of the 1756-CNB/D/E or 1756-CNBR/D/E
modules for both redundant chassis to the same node address.
1. For each module in the first redundant chassis, install an

identical module into the same slot of the second redundant
chassis.
2. Connect the CNB, ENBT, and EWEB modules to their respective
networks.
3. Connect one of the following fiber optic cables to the 1757-SRM
modules:
1757-SRC1
1757-SRC3
1757-SRC10
1757-SRC50
1757-SRC100
Install the System
Install the Remote Chassis

or Rails
51
You must install all I/O modules and additional types of

communication modules in remote chassis or on DIN rails. The
following example shows a remote 1756 chassis. You can use any
type of chassis or device that you can connect to the ControlNet
network.
DeviceNet network
L C E
5 N N
5 B B
T
S
R
M
L C E
5 N N
5 B B
T
S
R
M
C
N
B
I/O modules
D
N
B
42197
Other ControlNet node (s)

You must have at least 2 other nodes in addition to the redundant
chassis pair. See Lay Out the System on page 2.
IMPORTANT
If you connect the workstation to the network via a network

access port on a CNB module, use a CNB module in a remote
chassis. This lets a switchover occur after the failure of a
ControlNet tap of a primary chassis.
As you install the chassis, follow these guidelines:

Do not assign any device to the address of the CNB modules in
the redundant chassis plus one.
For example, if you set the rotary switches of the CNB modules
in the redundant chassis to node 11, no other device should use
node 12.
Use a remote chassis for communication modules such as:
1756-ENET
1756-DHRIO
1756-MVI
1756-DNB
52
Install the System
Configure the EtherNet/IP

Modules
To use an EtherNet/IP module, give it an IP address, subnet mask, and

gateway address:
Action
Details
1. Before you begin.
A. Perform the following steps if you havent already:

Install and connect both 1757-SRM modules
Get the IP address, subnet mask, and gateway address for each EtherNet/IP module.
See Plan the EtherNet/IP Networks on page 12.
B. Do you know how to configure an EtherNet/IP module in a nonredundant system?
If no, then continue with step C.
If yes, then go to step 2.
C. Get the following publication:
EtherNet/IP Modules in Logix5000 Control Systems, publication ENET-UM001
Youll use that publication when you configure each module.
2. Configure the EtherNet/IP modules in

the first chassis.
A. Turn on the power to only one of the redundant chassis.

For example, if both chassis are on, turn off one of them.
B. Configure the EtherNet/IP module in the chassis that is on.
C. Do you see the IP address on the front of the module?
If no, then return to step B.
If yes, then continue with step D.
D. Repeat steps 2B and 2C for each EtherNet/IP module in this chassis.
3. Configure the EtherNet/IP modules in

the second chassis.
A. Turn off the chassis that you just configured.

B. Turn on the other chassis.
C. Configure the EtherNet/IP module in the chassis that is on.
D. Do you see the IP address on the front of the module?
If no, then return to step C.
If yes, then continue with step E.
E. Repeat steps 3C and 3D for each EtherNet/IP module in this chassis.
Install the System
Flash the Modules

Redundancy Module
PRIM
PRI COM
OK
42801
53
1. Turn on the power to one of the redundant chassis.

2. Wait for the 1757-SRM module to display PRIM.
3. Flash upgrade each module in the chassis with a compatible
revision of firmware.
See the ControlFLASH Firmware Upgrade Kit User Manual,
publication 1756-6.5.6.
To find the chassis in RSLinx software, locate the node
number or IP address on the front of the communication
module.
4. Turn off the power to the chassis.
5. Turn on the power to the second redundant chassis.
6. Wait for the 1757-SRM module to display PRIM.
7. Flash upgrade each module in the chassis with a compatible
revision of firmware. Use the same revisions that you used for
the first redundant chassis.
Check Your Installation
Purpose
To make sure that your redundant chassis are able to synchronize
When
Complete this procedure after you:
install the system.
configure the communication modules.
update firmware.
54
Install the System
Actions
First chassis
turned on
Redundancy Module
PRIM
PRI COM
Second chassis
turned on
Redundancy Module
SYNC
OK
PRI COM
1. Turn on the chassis power to the partner (secondary) chassis.

2. Wait for the 1757-SRM module to complete its power-up cycle.
The SRM module takes 1 to 3 minutes to power up.
It may also take several minutes to synchronize the secondary
controller.
OK
42801
3. Does 1 of the 1757-SRM modules show PRIM and the other

module show SYNC?
Yes Stop. The system is synchronized.
No There is a problem. The system isnt synchronized. Go
to step 4.
4. Make sure that the Auto-Synchronization option of the SRMs is
set to Always. For help, see Chapter 4.
5. Does 1 of the 1757-SRM modules show PRIM and the other
module show SYNC?
Yes Stop. The system is synchronized.
No Go to Troubleshoot a Failure to Synchronize on page 5.
Chapter
Configure the System Redundancy Module
Purpose of This Chapter
This chapter shows how to set or change the configuration of a

1757-SRM module. The SRM module controls the synchronization and
switchover of your redundancy system.
Use this chapter after you have installed your system to:
change how the SRM supports your system.
restart your system after redundant chassis regain power after a
power loss.
Use this chapter as follows:
If
Do this
On page
You just installed your system
Open the SRM Configuration Tool
55
Check the Revision of Your SRM Configuration Tool
57
Check the Version of Your SRM Configuration Tool
59
Set the Clock of the SRM
61
Test a Switchover
63
You want to change how the SRM

supports your system
Change the Auto-Synchronization Option
65
Change the Program Control Option
66
Both redundancy chassis lost power
61
Open the SRM

Configuration Tool
Purpose
To open the 1757-SRM System Redundancy Module configuration tool
When
Complete this procedure to:
set the SRM clock.
55
56
test a switchover.
troubleshoot a system.
store or load a project using nonvolatile memory.
update firmware.
Before You Begin

RSLinx software includes and automatically installs the 1757-SRM
System Redundancy Module configuration tool.
IMPORTANT
Check your revision of the SRM configuration tool when you

open it for the first time.
The revision of tool that you get depends on your version of
RSLinx software.
Some revisions of the SRM configuration tool arent
compatible with some revisions of a ControlLogix
Redundancy system.
The next section shows you how to see if your revision of the
SRM configuration tool is right for your redundancy system.
Actions
1. Start RSLinx software.
Workstation
2. From the Communications menu, choose RSWho.
Linx Gateways, Ethernet
3. Double-click the network to open it.
My_Network
n, 1756 communication module
4. Double-click the communication module in the primary chassis

to show the backplane.
Backplane, 1756-Ax
xx, 1757-SRM
5. Double-click the backplane to see its modules.

6. Right-click the 1757-SRM module and select
Module Configuration.
57
What to Do Next
IMPORTANT
Make sure that you check the revision of your SRM

configuration tool before you use it. Later revisions of the SRM
configuration tool arent compatible with earlier revisions of
ControlLogix redundancy systems. See Check the Revision of
Your SRM Configuration Tool on page 57.
Check the Revision of Your Purpose

SRM Configuration Tool
To make sure that you are using the right revision of the SRM
configuration tool for your ControlLogix redundancy system
IMPORTANT
Make sure that you check the revision of your SRM

configuration tool.
Revision 2.6 is compatible only with revision 13.x or later
ControlLogix redundancy systems.
Youll cause the 1757-SRM module to fault if you use
revision 2.6 of the tool with an revision 11.x or earlier
redundancy systems.
58
When
Perform this procedure to:
use the SRM configuration tool for the first time.
connect to a different ControlLogix redundancy system for the
first time.
update the firmware of a ControlLogix redundancy system.
Before You Begin

RSLinx software automatically installs the SRM configuration tool. Use
the following table to see which revision of the tool that you get:
If you install
Then you get
RSLinx software revision 2.42
SRM configuration tool revision 2.5
RSLinx software revision 2.43
SRM configuration tool revision 2.6
59
Actions
Action
Details
1. Choose which revision to use.
Do you connect your computer to ControlLogix redundancy systems revision 11.x or

earlier?
Yes Use revision 2.5 of the SRM Configuration Tool. DONT use revision 2.6.
No Use revision 2.6 of the SRM Configuration Tool.
Revision 2.6 is compatible only with revision 13.x or later ControlLogix redundancy
systems. Youll cause the 1757-SRM module to fault if you use revision 2.6 of the tool with
an revision 11.x or earlier redundancy systems.
Keep in mind that some features are available only in revision 2.6 or later of the
configuration tool.
2. See which revision you have.
A. Open the SRM configuration tool if you havent already done so.
B. Right-click the title bar of the configuration tool and choose About
3. Change your revision
If you need a different revision of the SRM configuration tool, see:

Knowledgebase document G92234770.
To access Rockwell Automations Knowledgebase, go to
Important: The SRM configuration tool lets you install only 1 revision on your computer at
the same time. To change the revision, remove the revision that you installed earlier.
Check the Version of the

Configuration Tool
Purpose
To verify the version of your 1757-SRM System Redundancy Module
Configuration tool
When
Perform this procedure before you configure your 1757-SRM module.
60
Actions
Action
Details
1. In RSLinx software, browse to

1757-SRM.
A. Start RSLinx software.

B. Browse to your 1757-SRM.
2. Identify the configuration tool version
A. Right-click the SRM and choose Module Configuration.
B. Right-click the title bar of the configuration tool and choose About
61
Purpose
To set clock of the 1757-SRM module
When
Perform this procedure:
after system installation.
after power loss to both chassis.
Before You Begin

The SRM clock records when significant events occur. Please note the
following characteristics of the SRM clock:
Only the primary SRMs clock requires setting. The secondary
SRMs clock synchronizes itself to the primary SRMs clock.
The SRM has no battery to keep its clock running. The clock
stops without SRM power.
With power, the primary SRM synchronizes its clock to the most
recent event in its event log.
The secondary SRM event log records when the secondary SRM
powered up. Look for WCT time change ( > 1 second) event.
An SRM with a firmware revision 3.37 or earlier doesnt log its
power-down time. If only one of the chassis powers down, use
the event log of the other chassis to see when it happened. Look
for The partner RM screamed event. See Interpret the SRM Event
Log on page 10.
Actions
Action
Details
1. Open the SRM configuration tool for the

primary chassis.

B. From the Communications menu, choose RSWho.
C. Open the network branches until you find the 1757-SRM module in the primary chassis.
D. Right-click the SRM and choose Module Configuration.
62
Action
Details
2. Set the clock.
A. Click Configuration.
B. Do you want to set the clock of the SRM to the clock of your computer?
If
Then
Yes
Choose Apply Workstation Time and then Yes.
No
1. Change the date or time.

2. Choose Set and then Yes.
C. Choose OK.
Test a Switchover
63
Purpose
To use RSLinx software to manually initiate a switchover
When
Perform this procedure after youve synchronized your system and
want to test a switchover.
Before You Begin

The CNB modules in the new primary chassis show the
synchronization progress after a switchover. Typically, the modules
show the following sequence:
43130
PwNS
PwDS
PwQg
PwQS
primary with no
secondary
primary with
disqualified
secondary
primary with
synchronizing
(qualifying)
secondary
primary with
synchronized (qualified)
secondary
Actions
Action
Details

primary chassis.

64
Action
Details
2. Start a switchover.
A. Click Synchronization.
B. Choose Initiate Switchover and then choose Yes to continue.

3. Monitor the synchronization progress.
A. Click Synchronization Status.
If the controller contains a large project, the system may spend some time
synchronizing the secondary controller.
B. If the Secondary Readiness remains Disqualified:
Make sure the Auto-Synchronization option = Always.
See Troubleshoot a Failure to Synchronize on page 5.
Change the
Auto-Synchronization
Option
65
Purpose
To change when the 1757-SRM module tries to synchronize the
controllers
When
help synchronize the system.
prevent the system from crossloading changes.
Actions
Action
Details
1. Decide when you want the system to

synchronize.
Do you plan to manually disqualify a chassis so you can make changes?

No Choose Always
Yes Choose Conditional
If you choose:
Then:
Conditional
The SRM keeps the synchronization command that you give it. If
you:
synchronize the secondary, the SRM always tries to keep the
controllers synchronized.
disqualify the secondary, the SRM keeps the controller
unsynchronized (disqualified). It doesnt crossload changes.
Never
primary chassis.
The controllers wont try to synchronize, but you can still manually
synchronize the controllers.

C. Open the branches of your network until you find the 1757-SRM module in the primary
chassis.
66
Action
Details
3. Set the auto-synchronization option.
B. Select the Auto-Synchronization option.

C. Choose Apply and then Yes to continue.
D. Choose OK.
Change the Program

Control Option
Purpose
To let the controller send a message to the 1757-SRM module or block
the controller from sending a message to the 1757-SRM module
When
Do this procedure when you:
initially configure the SRM.
decide to send the SRM a message from the controller.
Before You Begin

See page 94 for a list of messages that a controller can send to an SRM
module.
67
Actions
Action
Details

primary chassis.

C. Open all the network branches to find the 1757-SRM module in the primary chassis.
2. Set the program control option.
B. Do you want to let a controller send a message to the SRM?
Yes Check the Enable User Program Control check box.
No Uncheck the Enable User Program Control check box.
C. Choose Apply and then Yes to continue.

D. Choose OK.
68
Notes:
Chapter
Configure and Program the Controller
After having installed a system, use this chapter to configure and

program the controller for redundancy.
IMPORTANT
Plan for Online Edits
Create and maintain only one RSLogix 5000 project for the pair
of redundant controllers. When you download the project to the
primary controller, the project automatically crossloads to the
To configure and program a controller, complete the following tasks:

Topic
Page
Plan for Online Edits
69
Configure Communications
74
Estimate the Crossload Time of a Program
77
Minimize Scan Time
79
Maintain the Integrity of Your Data During a Switchover
85
Determine the Status of Your Redundancy System
90
Condition Logic to Run After a Switchover
91
Send a Message to the SRM
94
Download the Project to the Primary Controller
98
Schedule the ControlNet Networks
98
Set the Task Watchdog Times
102
Before editing online:

decide if you want to keep test edits after a switchover.
be aware that finalizing edits removes your original logic.
decide how you want to set aside unused memory.
69
70
Decide if You Want to Keep Test Edits after a Switchover

When you edit logic while online with the controller, the edits may
fault the controller and cause a switchover.
Test Edits
If test edits fault the primary controller, they will likely also fault the
secondary controller. To prevent faulting, any test edits are
deactivated (untested) during a switchover. As an option, you can
keep the edits active after a switchover:
If you want to
Then
Prevent an incorrect online edit from

faulting both the primary and secondary
controller
Do not retain test edits (default setting).
Keep test edits active during a switchover

(at the risk of faulting both controllers)
Retain test edits.
71
Be Aware That Finalizing Edits Removes Your Original Logic

Finalize All Edits in Program
The controller removes the original logic when you finalize all edits in
a program. If your changes cause a major fault and a switchover, the
new primary controller also faults. Thats because theres NO original
logic to go back to. For example, the new primary controller cant
untest the edits.
This happens even if you set the
controller to untest edits on a
switchover.
Decide How You Want to Set Aside Unused Memory

IMPORTANT
We recommend that you leave the Memory Usage slider in the

middle (default).
When the secondary controller receives crossload data, it first buffers

tag data in a quarantine section of memory. When it has all of the data
and knows it is valid, it moves the data into the main memory area.
That is why a redundant controller requires twice as much memory
for tags as a nonredundant controller.
72
The controller sets up the quarantine area at the time of download:

The controller divides its memory into two sections:
tags, including a quarantine area
logic
The controller also divides its unused memory. It reserves a
specific amount for tags that you create while online. The rest
for logic.
You configure how to reserve unused memory between tags and
logic. You do this online in program mode.
If you plan to
Then
While online, create roughly the same amount of new

tags and new logic
Leave the default setting.
While online, create a relatively large amount of new

tags but a much smaller amount of new logic
Drag to slider toward Tags.
Notes
Avoid setting the slider all the way to Tags:

You will be unable to perform online edits.
OPC communications may error or fail.
While online, create a relatively large amount of new

logic but a much smaller amount of new tags
Configure a Controller for

Redundancy
Drag to slider toward Logic.
Avoid setting the slider all the way to Logic;

you will be unable to create tags while online.
1. Open or create the RSLogix 5000 project.
2. On the Online toolbar, click the controller button.

3. Does General display the controller type?
If no, go to step 4.
If yes, go to step 7.
4. Click the Change Type button.
5. Select your controller.
6. Choose OK.
7. Click Redundancy.
73
8. Select the Redundancy Enabled check box.
9. Click the Advanced button.
10
11
10. We recommend that you not check this box. Leaving it

unchecked prevents an incorrect online edit from faulting both
the primary and secondary controller.
If you want any test edits to remain active during a switchover,
then check this box. However, by doing so, you run the risk of
faulting both controllers.
11. We recommend that you leave the Memory Usage slider in the
middle, the default position.
12. Choose
13. To close the Controller Properties dialog box,
choose
74
Configure Communications
A redundant system requires some specific configuration choices for

successful communications. Use this section to perform the following
redundancy tasks:
Configure
Configure
Configure
Configure
IMPORTANT
I/O
produced tags
message (MSG) instructions
tags for an HMIConfigure I/O
For each module in your system, make sure that the requested
packet interval (RPI) is less than or equal to 375 milliseconds. If
you use a larger RPI, the controller could lose its connection
with the module during a switchover. This could cause outputs
to change state.
For any outputs that require a bumpless switchover:

put those outputs in the highest priority task.
configure only that task at the highest priority.
Configure Produced Tags

IMPORTANT
During a switchover, the connection for tags that are consumed

FROM a redundant controller may time out.
The data DOES NOT update.
The logic acts on the last data that it received.
After the switchover, the connection reestablishes and the data

begins to update again.
If you want a controller in another chassis to consume a tag from the

redundant controller, use a comm format of None. In the I/O
configuration of the consuming controller, select a comm format of
None for the remote CNB module (the CNB that is physically in the
redundant chassis).
75
Produced tag
To the controller with the consumed tag, this
is the remote CNB module.
Redundant chassis
L C
5 N
5 B
M
S
R
M
Data
Consumed tag
Remote chassis
C L
N 5
B 5
M
x
In the I/O configuration of this controller, select a communication

format of None for the remote CNB module.
76
Configure Message (MSG) Instructions

If the MSG instruction
is
Then
From a redundant
controller
In a redundant controller, any MSG instruction that is in progress during a switchover experiences an error.
(The ER bit of the instruction turns on.) After the switchover, normal communication resumes.
To a redundant controller
For any MSG instruction from a controller in another chassis to a redundant controller, cache the connection:
Properties of the Message to the Redundant Controller
Path to the
redundant controller
42977
Leave this box checked
Configure Tags for an HMI

To monitor tags directly in the secondary controller (not typical),
monitor from no more than 3 devices through a CNB module.
Monitor tags in a secondary controller only via:
RSLogix 5000 software
Any method that does not try to create OPC optimized packets.
Only a primary controller can create an OPC optimized packet.
Estimate the Crossload

Time of a Program
77
Purpose
To estimate the crossload time of a program in a redundant controller
When
Perform this procedure to gauge the time a project spends
crossloading data.
Before you begin

Consideration
Details
The controller crossloads data at the end of

every program.
The primary controller stops at the end of every program to crossload fresh data to the
secondary controller. This keeps the secondary controller up to date and ready to take over.
It also increases the scan time when compared to a nonredundant system.
Scan time of program

Execute program in
primary controller
Start of program
The crossload time depends on how much

data changed.
Crossload results to
End of program
The length of time for the crossload depends on the how much data the primary controller
has to crossload.
The primary controller crossloads any tag to which an instruction wrote a value (even
the same value) since the last crossload.
Crossloading also requires a small amount of overhead time to tell the secondary
controller which program the primary controller is executing.
In a redundant system, a ControlLogix5561,

5562, or 5563 controller is up to 30% faster
than a ControlLogix5555 controller.
The scan time improvement of ControlLogix5561, 5562, and 5563 controllers is less in a
redundant system is than in a nonredundant system.
Even though the ControlLogix5561, 5562, and 5563 controllers execute logic faster,
they must still crossload data.
Given the same project and redundant system, a ControlLogix5561, 5562, or 5563
controller is up to 30% faster than a ControlLogix5555 controller.
78
Actions
Action
Details
1. Get the size of your crossload data.
Use a Get System Value (GSV) instruction to read the REDUNDANCY object.
For this information
Get this attribute
Size of the last crossload LastDataTransfer

Size of the last crossload Size
Data
Type
Description
DINT
This attribute gives the size of data that was or would have
been crossloaded in the last scan.
if you had a secondary

chassis
The size in DINTs (4-byte words).

You must configure the controller for redundancy.
You dont need a secondary chassis.
Is there a synchronized secondary chassis?
Yes This gives number of DINTs that was crossloaded
in the last scan.
No This gives number of DINTs that would have been
crossloaded in the last scan.
Size of the biggest

crossload
MaxDataTransfer
Size
Size of the biggest

crossload if you had a
secondary chassis
DINT
This attribute gives the biggest size of the LastDataTransfer

Size attribute.
To reset this value, use an SSV instruction with a Source
value of 0.
Yes This gives biggest number of DINTs that was
crossloaded.
No This gives biggest number of DINTs that would
have been crossloaded.
See Logix5000 Controllers General Instructions Reference Manual, publication

1756-RM003, for more information on the GSV and SSV instructions.
2. Estimate the crossload time.
Which controller do you have?

If ControlLogix5555, then crossload time = (0.0015 ms * DINTs) + 1 ms overhead
where DINTs is the size of tag data to be crossloaded, measured in 4-byte words.
Minimize Scan Time
79
To minimize a projects scan time, perform the following procedure:

IMPORTANT
Dont try to get the scan time of a ControlLogix redundancy

project down below about 20 milliseconds. At very low scan
times, crossload data becomes a bigger performance burden.
This burden limits the minimum scan time.
Action
Details
1. Use a few large programs instead of a lot

of small programs.
The controller stops at the end of every program to crossload data. So the more programs
that you have, the more the controller stops to crossload. And it often ends up
crossloading the same data many times.
To cut down the number of crossloads:
A. Use only one or a few programs.
B. Divide each program into whatever number of routines makes the most sense. A
routine doesnt cause a crossload.
C. Use the main routine of each program to call the other routines of the program.
D. If you want to use several tasks for different scan periods, put only one program in
each task. Remember that each program adds a crossload. So use only one or a few
tasks.
This is better
Than this
80
Action
Details
2. Delete unused tags.
This reduces the size of the tag database. A smaller database takes less time to crossload.
To delete unused tags:
A. Open one of the tags folders.
B. Click Edit Tags.

C. From the Show list, select Unused.
D. From the Edit menu, choose Select All.

E. Press the [Delete] key.
3. Use arrays and user-defined data types
instead of individual tags.
When you create a tag, the controller always sets aside at least 4 bytes (32 bits) of
memory. The controller does this even if the tag needs only 1 bit.
When you create an array or a user-defined data type, the controller packs smaller data
types into 4-byte (32-bit) words. This means the controller has less data to crossload.
This array of 32 BOOLs takes only 4-bytes.
The controller crossloads only 4 bytes.

These 3 BOOL tags take 12 bytes total (3 tags x 4 bytes/tag = 12 bytes).
The controller crossloads all 12 bytes.

Arrays and user-defined data types help you the most with BOOL tags. But also use them
for your SINT, INT, DINT, REAL, COUNTER, and TIMER tags.
81
Action
Details
4. If youve already created individual tags,

change them to aliases.
If youve already created individual tags, change them to aliases for elements of an array.
Your logic points to the aliases. The controller crossloads the base array.
A. Create an array.
B. Change each individual tag to an alias for an element in the array.
C. Keep pointing your logic to the

individual tag names.
5. Keep user-defined data types as compact

as possible.
Put like data types together when you lay out a user-defined data type:
Put all the BOOLs together.
Put all the SINTs together.
Put all the INTs together.
This is better
This data type takes 12 bytes. The BOOLs are together.
Than this
This data type takes 20 bytes. The BOOLs are spread out.
82
Action
Details
6. Keep code as compact as possible.
Avoid checking the same conditions many times. Each instruction adds scan time to your
controller.
This is better
This rung checks Bool_B and Bool_C only once each scan.
Than this
This rung checks Bool_B and Bool_C twice each scan. One or two instructions dont add much
scan time. But if you do this often, the extra instructions add up to a much longer scan time.
Action
Details
7. Execute code only when you need it.
The controller crossloads a tag anytime an instruction writes a value to the tag. This
happens even if the value stays the same:
83
Many instructions write a value whenever they run. For example, instructions such as
OTL, OTU, and many instructions with Destination operands write a value each time
the rung-condition-in is true.
Whenever an instruction writes a value, the controller marks the value for the next
crossload. This occurs even if the instruction wrote the same value that was previously
in the tag.
If you execute an instruction only when you need to, you reduce the amount of crossload
data. This reduces scan time. To limit the execution of an instruction:
Make a rung false when you dont need to execute its instructions.
Divide your logic into subroutines and call each subroutine only when needed.
Run noncritical code every few scans instead of every scan.
This is better
The ADD instruction runs only when the controller gets new data (New_Data = on). And
Dest_Tag crossloads only when the ADD instruction produces a new value.
Than this
The ADD instruction writes the sum of Tag_1 + Tag_2 to Dest_Tag each time the rung
executes. The controller crossloads Dest_Tag every scan, even if Tag_1 and Tag_2 stay the
same.
84
Action
Details
8. Group your data by how often you need it. To update the secondary controller, the primary controller divides its memory into blocks of
256 bytes. Anytime an instruction writes a value, the primary controller crossloads the
entire block that contained the value. For example, if your logic writes only 1 BOOL value
to a block, the controller crossloads the entire block (256 bytes).
To minimize crossload time, group your data by how often you need it.
Suppose that you have some DINTs that you use only as constants to initialize your logic.
You have some BOOLs that you update every scan. And you have some REALs that you
update every second.
This is better
One user-defined data type for the
BOOLs. The controller crossloads these
4 bytes every scan.
One user-defined data type for the DINTs.
The controller crossloads these 12 bytes
only once.
One user-defined data type for the REALs.
The controller crossloads these 12 bytes
every second.
Than this
One user-defined data type for all the
data. The controller crossloads these
28 bytes every scan.
9. Use DINT tags instead of SINT or INT

tags
To keep your logic as efficient as possible, use the DINT data type instead of the SINT or
INT data types.
A ControlLogix controller usually works with 32-bit values (DINTs or REALs). If you use a
SINT or INT value:
The controller usually changes a SINT or INT value to a DINT or REAL value before it
uses the value.
If the destination is a SINT or INT tag, the controller usually changes the value back to
a SINT or INT value.
You dont have to program the controller to change values to or from SINTs or INTs. The
controller does it automatically. But it takes extra execution time and memory.
Maintain the Integrity of

Your Data During a
Switchover
85
The redundancy system guarantees a bumpless switchover for any

logic in the highest priority task. In some cases, a switchover may
make lower priority tasks repeat part of their scan. This has to do with
how data crossloads from the primary controller to the secondary
controller.
As the primary controller executes its logic, it updates the secondary
controller at the end of every program.
Interruption by the program

in a higher priority task
End of the program in a

higher priority task
Start of the program in the lower priority

task (for example, the continuous task)
A.
End of the program in the lower

priority task
Primary controller
C.
B.
A. The following data is sent to the secondary controller:

Data from the program in the higher priority task
Data from the first part of the program in the lower priority
task
B. Execution returns to the program in the lower priority task.
C. Data from the second part of the program in the lower priority
task is sent to the secondary controller.
When a switchover interrupts the execution of the primary controller,
the secondary controller reexecutes an interrupted program from the
beginning of the program.
86
Interruption by the program

in a higher priority task
End of the program in a

higher priority task
Start of the program in the lower priority

task (for example, the continuous task)
A.
This portion of the task is not executed
during this scan.
Primary controller
Switchover
occurs
B.
Instructions executing at the time of the

switchover do not complete in this scan.
Secondary controller
C.
A. The following data is sent to the secondary controller:

Data from the program in the higher priority task
Data from the first part of the program in the lower priority
task
B. Execution returns to the program in the lower priority task.
C. The secondary controller:
starts the scan at the beginning of the program that was in
progress in the primary controller during the switchover.
uses the data from the last update.
In this example, the secondary controller starts the scan with an
image of the data as it was during the primary controllers last
scan.
To prevent a scan from repeating after a switchover:
look for array shift instructions.
look for scan-dependent logic.
take preventative actions
87
Look for Array Shift Instructions

The following instructions might corrupt data during a switchover:
BSL
BSR
FFU
Because these instructions shift data within an array, an interruption
by a higher priority task and a subsequent switchover leaves the data
with an incomplete shift.
If a higher priority task interrupts one of these instructions, the
partially shifted array values are sent to the secondary controller.
If a switchover occurs before the instruction completes its
execution, data remains only partially shifted.
The secondary controller starts its execution at the beginning of
the program. When it reaches the instruction, it shifts the data
again.
Look for Scan-Dependent Logic

A rung that must read the output of another rung during the same
scan might miss a scan during a switchover. For example:
A.
C.
D.
B.
43065
A. The CTU instruction counts each scan.

B. The EQU instruction uses the count of each scan
(scan_count.ACC).
88
C. If a higher priority task interrupts the logic, the value of

scan_count.ACC is sent to the secondary controller at the end of
the program in the higher priority task.
D. If a switchover occurs before the EQU instruction, the secondary
controller starts its execution at the beginning of the program.
The EQU instruction misses the last value of scan_count.ACC.
Take Preventative Actions

If logic seems susceptible to an upset during a switchover, take one of
the following preventative actions:
1. Place susceptible logic in the highest priority task.
2. If the logic must remain in a lower priority task, take one of the
following actions:
Use UID and UIE Instruction Pairs.
Buffer critical data.
Place Susceptible Logic in the Highest Priority Task

This prevents the controller from sending any data to the
secondary controller until the program finishes.
If a switchover occurs during the program, the secondary
controller repeats the scan using the same starting data.
89
Use UID and UIE Instruction Pairs

Bound critical rungs with UID and UIE instruction pairs. This prevents
the higher priority task form interrupting the scan-dependent logic, as
shown below:
Buffer Critical Data

The following example shows the use of a buffer together with a BSL
instruction.
1.
2.
3.
43065
1. The COP instruction moves the data into a buffer array.

2. The BSL instruction uses the data in the buffer. If a switchover
occurs, the source data (array tag) remains unaffected.
3. The CPS instruction updates array tag. Since higher priority
tasks cannot interrupt a CPS instruction, the instruction keeps
the integrity of the data.
90
Determine the Status of

Your Redundancy System
Purpose
To write code that determines the status of your redundancy system
When
show system status on an HMI screen.
condition code to execute based on system status.
get diagnostic information to troubleshoot a system.
Actions
Use a Get System Value (GSV) instruction to read the attributes of the
REDUNDANCY object. See Appendix C for a list of attributes.
Example 1: Ladder Diagram

Get the ID of the primary chassis. The primary chassis always runs the code.
Store the ID in the Chassis_ID_Now tag. Chassis_ID_Now is a DINT.
Example 2: Structured Text

comment
comment
comment
//Get the ID of the primary chassis.

//Thats always the chassis that runs the code.
//Store the ID in Chassis_ID_Now. Chassis_ID_Now is a DINT.
code
GSV(REDUNDANCY,,PhysicalChassisID,Chassis_ID_Now);
91
Check Your Work

Use the Redundancy tab of the Controller Properties window to check
the code attributes. It doesnt show all the attributes, but it shows the
more common attributes.
1. Download and run your project.
2. Open the Controller Properties window.
3. Click Redundancy.
4. Compare the Redundancy tab with your code.

In this example, the chassis ID A = 1.
For More Information

For more information on
See
Attributes of the REDUNDANCY object
Appendix C
GSV and SSV instructions
Logix5000 Controllers General Instructions

Reference Manual, publication
1756-RM003
Condition Logic to Run After Purpose

a Switchover
To condition a section of your logic to run after a switchover
92
When
Follow these examples to create logic in preparation for a possible
switchover:
Example 1: Ladder Diagram

Get the ID of the primary chassis. Thats always the chassis that runs the code.
Store the ID in the Chassis_ID_Now tag.
Chassis_ID_Now DINT.
If this is the first scan then

Set the last value of the chassis ID = the ID of this chassis.
Chassis_ID_Last DINT.
If the chassis ID changes, a switchover happen

ed. If a switchover happens, then
Turn on the Switchover_Happened bit.
Set the last value of the chassis ID = the ID of this chassis.
Switchover_Happened BOOL.
Continued on next page
93
If Switchover_Happened = on, then

Execute the instructions that you want to execute after a switchover.
Turn off the Switchover_Happened bit.
Put your instructions here.
Example 2: Structured Text

comment
comment
comment
comment
//Get the ID of the primary chassis.

//Thats always the chassis that runs the code.
//Store the ID in Chassis_ID_Now.
//Chassis_ID_Now -- DINT.
code
GSV(REDUNDANCY,,PhysicalChassisID,Chassis_ID_Now);
//If this is the first scan
//Then set the last value of the chassis ID = the ID of this chassis
//Chassis_ID_Last -- DINT.
If S:FS then
Chassis_ID_Last := Chassis_ID_Now;
End_If;
//If the chassis ID changes, a switchover happened.
//If a switchover happens then
//Turn on the Switchover_Happened bit.
//Set the last value of the chassis ID = the ID of this chassis
//Switchover_Happened -- BOOL
94
If Chassis_ID_Now <> Chassis_ID_Last then

Switchover_Happened := 1;
Chassis_ID_Last := Chassis_ID_Now;
End_If;
//If Switchover_Happened = on
//Then
//Execute the instructions that you want to execute after a switchover.
//Turn off the Switchover_Happened bit.
If Switchover_Happened then
Put your statements here.
Switchover_Happened := 0;
End_If;
Send a Message to the

SRM
Purpose
To let your logic initiate actions in the SRM
When
initiate a switchover.
Disqualify the secondary controller.
Synchronize the secondary controller.
Set the clock of the SRM module.
95
Before You Begin

Before sending a message to an SRM, make sure that:
the SRM is configured for program control.
the message is unconnected.
Leave the Connected check

box clear (unchecked).
96
Actions
Use the following table to configure a message to an SRM module:
Configuring a Message to an SRM
If you want to
On this tab
For this item
Type or select
initiate a switchover
Configuration
Message Type
CIP Generic
Service Code
4e
Class name
bf
Instance name
Attribute name
leave blank
Source
DINT tag with a value of 1
Num. Of Elements
Destination
leave blank
Path
1, slot_number
Communication
where:
slot_number is the left-hand slot number of the
1757-SRM module.
Disqualify the secondary

controller
Configuration
Communication
Connected check box.
Leave the Connected check box clear (unchecked). You can

send only unconnected messages to a 1757-SRM module.
Message Type
CIP Generic
Service Code
4d
Class name
bf
Instance name
Attribute name
Leave blank
Source
Num. Of Elements
Destination
Leave blank
Path
1, slot_number
where:
1757-SRM module.

97
Configuring a Message to an SRM (Continued)

If you want to
On this tab
For this item
Type or select
Synchronize the secondary

controller
Configuration
Message Type
CIP Generic
Service Code
4c
Class name
bf
Instance name
Attribute name
Leave blank
Source
Num. Of Elements
Destination
Leave blank
Path
1, slot_number
Communication
where:
1757-SRM module.
Set the clock of the SRM

module
Configuration

Message Type
CIP Generic
Service Code
10
Class name
8b
Instance name
Attribute name
Source
WallClockTime[0]
where:
WallClockTime is a DINT[2] array that stores the
CurrentValue of the WALLCLOCKTIME object.
Communication
Num. Of Elements
Destination
Leave blank
Path
1, slot_number
where:
1757-SRM module.
Connected check box

98
Download the Project to the

Primary Controller
You only have to download the project to the primary controller.

When the secondary controller is synchronized, the system
automatically crossloads the project to the secondary controller.
IMPORTANT
If the secondary chassis becomes disqualified after you

download the project, make sure that you:
configured the project for the right type of controller.
enabled redundancy.
See Plan for Online Edits on page 69.
1. Open or create the RSLogix 5000 project for the controller.

2. From the File menu, choose Save.
3. From the Communications menu, choose Who Active.
4. Browse to the controller in the primary chassis.
A. Open a branch in one of these ways:

Double-click it.
Click its + sign.
Workstation
+
My_Network
Select it and press the key.
n, 1756 communication module
Backplane, 1756-Ax
B. Find the primary chassis. Its communication

module uses the address that you gave it.
C. Find the controller.
xx, 1756 controller
5. Select the controller and choose Download.

A confirmation box opens.
6. Choose Download.
Schedule the ControlNet

Networks
IMPORTANT
Before you schedule a ControlNet network, turn on the power

to both redundant chassis. If you schedule a ControlNet
network while the secondary chassis is off, the keeper
signature of a CNB module may not match its partner, and the
secondary chassis will fail to synchronize.
99
To schedule a ControlNet network:
schedule a new network.

update the schedule of an existing network.
check the keepers.
save the project for each controller.
Schedule a New Network

1. Turn on the power to each chassis.
2. Start RSNetworx for ControlNet software.
3. From the File menu, choose New.
4. From the Network menu, choose Online.
5. Select your ControlNet network and choose OK.
6. Select the Edits Enabled check box.
7. From the Network menu, choose Properties.
8. From Network Parameters, type or select the following
parameters:
In this box
Specify
Network Update Time
Repetitive time interval in which data is sent over the ControlNet network
Max Scheduled Address
Greatest node number to use scheduled communications on the network
Max Unscheduled Address
Greatest node number that you will use on the network
Media Redundancy
Channels in use
Network Name
Name for the network
9. Choose OK.
10. From the Network menu, choose Single Pass Browse.
12. Type a name for the file that stores the network configuration,
then choose Save.
13. Select the Optimize and rewrite Schedule for all Connections
button (default) and choose OK.
100
Update the Schedule of an Existing Network

1. Turn on the power to each chassis.
2. Start RSNetworx for ControlNet software.
3. From the File menu, choose Open.
4. Select the file for the network and choose Open.
5. From the Network menu, choose Online.
6. Select the Edits Enabled check box.
7. From the Network menu, choose Properties.
8. From Network Parameters, update the following parameters:
In this box
Specify
Max Scheduled Address
Greatest node number to use scheduled communications

on the network
Max Unscheduled Address
Greatest node number to use on the network
9. Choose OK.
10. From the Network menu, choose Single Pass Browse.
12. Select the Optimize and rewrite Schedule for all Connections
button and choose OK.
Check the Keepers

On a ControlNet network, each keeper must:
take over the keeper duties if the current keeper drops off the
network.
use the same configuration regardless of which keeper first
comes online after a major network disturbance, such as a cable
short or system power cycle.
101
After you schedule your ControlNet networks:

1.
2.
Keeper Capable Node
Active Keeper Valid Keeper
offline file
N/A
N/A
01
No
Yes
02
Yes
Yes
1. Make sure the network shows all keeper capable nodes.

2. Make sure that each node is a valid keeper.
For more information, see Update a Keeper Signature on page 6.
Save the Project for Each Controller

After your schedule your ControlNet networks, save the online project
of each controller. This lets you download a project in the future
without having to reschedule the networks.
For each controller (redundant and nonredundant) on a ControlNet
network:
1. Go online to the controller.
2. Save the project.
102
Set the Task Watchdog

Times
Give a redundant controller longer watchdog times than a

nonredundant controller.
After a switchover, the secondary controller starts the scan at the
beginning of the program that was running in the primary
controller at the time of the switchover.
The watchdog timer for the task that has the program, however,
is not reset.
A major fault happens (type 6, code 1) if the watchdog timer has
too little time to completely rescan the program.
Action
Details
1. Set the minimum watchdog time for a

task.
Use the following formula to set the minimum watchdog time for a task:
Minimum watchdog time = (2 * maximum_scan_time) + 150 ms
where:
Maximum_scan_time is the maximum scan time for the entire task when the
secondary controller is synchronized.
2. Set the estimated watchdog time for a

task.
+
Controller Primary
Tasks
+
MainTask
A. Right-click the task and choose Properties.

B. Click Configuration.
C. Type a watchdog time that is

more than the watchdog time
from step 1.
D. Choose OK.
Action
Details
3. Determine the real scan time of a task.
Do the following steps while the controller is running.
Controller Primary
Tasks
+
MainTask
103
A. Right-click the task and choose Properties.

B. Click Monitor.
C. Look at the scan times.

Longest time its taken in microseconds
to scan this task
Time it took in microseconds to scan this
task the last time it ran
D. If you want to clear the Max counters and
start over, click Reset.
E. Choose OK.
4. See if the watchdog time is big enough.
A. Calculate the smallest watchdog time for your task using the real scan time of the task:
Smallest watchdog time = (2 * maximum_scan_time) + 100 ms
B. Is your watchdog time more than the smallest watchdog time from step 4A above?
Yes Stop. Your watchdog time is OK.
No Repeat step 2 and enter a new watchdog time.
104
Notes:
Chapter
Maintain and Troubleshoot the System

Simultaneous power of redundant
chassis pair may bump another
redundant chassis pair off the
EtherNet/IP network
This chapter provides a variety of procedures to commission, upgrade,

maintain, and troubleshoot your redundancy system.
Under the following combination of conditions (all must apply), duplicate IP addresses on your
EtherNet/IP network will cause you to lose communication with a redundant chassis pair over that
EtherNet/IP network:
You have multiple pairs of redundant chassis on the same EtherNet/IP network. For example,
pair 1 and pair 2.
The IP addresses of one pair of redundant chassis is the same as another pair of redundant
chassis. For example, pair 1 = 10.10.10.10 and pair 2 = 10.10.10.10.
A redundant chassis pair with the conflict (both chassis that make up the pair) simultaneously
powers up. For example, both chassis of pair 2 power up at the same time.
When this occurs the newly powered up chassis use the IP address. The redundant chassis pair
that was previously communicating at that IP address stops communicating on the network. For
example, when pair 2 powers up at 10.10.10.10, pair 1 stops communicating on the network.

If you want to
Then see this section
Page
Find the Cause of a Switchover or

Disqualification
106
Find why the secondary controller fails to synchronize
Troubleshoot a Failure to Synchronize
108
See if the keeper signature of a CNB module is stopping the

secondary chassis from synchronizing
Update a Keeper Signature
110
See if a computer is stopping the secondary chassis from

synchronizing
See if an Edit Session Is in Progress
111
Look through a log of events to see why system switched

over or failed to synchronize
Interpret the SRM Event Log
113
Find the cause of an unplanned switchover

Find why secondary chassis became disqualified
Export specific events from the SRM event log and view them Export the SRM Event Log
in software such as Microsoft Excel
119
Initiate the synchronization process
Manually Synchronize the Chassis
122
Optimize Communication
123
Check the Allocation of Unused Memory
127
Determine why it takes a very long time to synchronize

the secondary controller
Determine why communication with your HMIs is very
slow
Determine why OPC communication has errored or failed
Determine why you are unable to create tags or edit logic
while online
105
106
If you want to
Determine the CPU usage of a CNB module
Then see this section
Page
Adjust CNB Usage
127
Reduce the CPU usage of a CNB module

Store a project to the nonvolatile memory of a controller
in a redundant system
Store or Load a Project Using Nonvolatile 137

Memory
Load a project into the controller from the nonvolatile

memory of the controller
Replace 1756-CNB/D or 1756-CNBR/D module(s) with series
E modules
Change CNB modules from Series D to

Series E
131
Change the revision of a module while minimizing the time

your system is off
Update a Module
140
Store an updated project and firmware to the nonvolatile

memory of the controller while the process is running
Store a Project to Nonvolatile Memory

While a Process Is Running
139
Update the firmware of a redundant chassis without shutting

down the process
Update a System That Is Already at

Revision 13
142
Find the Cause of a

Switchover or
Disqualification
Purpose
To find and fix the cause of an unplanned switchover or loss of
synchronization
When
Perform this procedure when:
an unplanned switchover happens.
a chassis that was synchronized becomes disqualified.
Actions
Start here.
1. Do the 1756-CNB/D/E or 1756-CNBR/D/E modules in the

primary chassis show PwQS?
Yes Go to Interpret the SRM Event Log on page 113.
No Go to step 2.
2. Does any module in the primary chassis show PwNS?
Yes Go to step 3.
No Go to step 6.
107
3. Use the following table to troubleshoot the secondary chassis:

If the secondary chassis
And each communication

module in the primary
chassis
And a secondary
communication module
has a
Then
Has power
Has a matching partner in the

secondary chassis
Red OK light
Replace the module.
Green OK light
Check the 1757-SRC cable for a

proper connection.
Doesnt have a matching partner

in the secondary chassis
Install a matching module.
Doesnt have power
Restore the power.
4. Wait several minutes for the system to try to synchronize.

5. What do the CNB modules in the primary chassis show?
PwQS Stop. Your system is synchronized.
PwDS Go to step 6.
6. Use the following table to troubleshoot the secondary chassis:
If the SRM module
has a
And a secondary CNB

module
And a secondary controller

has a
Then
Green OK LED
Doesnt show NET ERR
Flashing Red OK light
Clear the major fault of the controller.

Its possible that you have to clear the fault on
both the primary and secondary controllers.
Solid Red OK light
A. Cycle the power to the chassis.

B. If the OK light remains solid red, replace the
controller and flash the controller with the
appropriate revision of firmware.
Solid Green OK light

Shows NET ERR
Red OK LED
Go to step 7.
Check all ControlNet taps, connectors, and
terminators for proper connections.
A. Cycle the power to the chassis.
B. If the OK light of the SRM module remains
solid red, contact your local distributor or
Rockwell Automation representative.
7. Wait several minutes for the system to try to synchronize.

8. Do the CNB modules in the primary chassis show PwQS?
Yes Stop. Your system is synchronized.
No Go to Troubleshoot a Failure to Synchronize on
page 108.
108
Troubleshoot a Failure to
Synchronize
IMPORTANT
If the steps in this section do not correct the situation, check the
usage of the CNB modules. See Adjust CNB Usage on page 127.
If the chassis still doesn't synchronize, try to manually synchronize it.
See Manually Synchronize the Chassis on page 122.
1. Look at the 1756-CNB/D/E or 1756-CNBR/D/E modules in the

primary chassis:
Primary CNB Front panel
Look here.
If
It means
So do this
PwQS
Primary with Synchronized

(Qualified) Secondary
Stop. The redundant chassis are

synchronized.
PwDS
Primary with Disqualified Secondary Go to step 2. A problem exists. The

redundant chassis are not
Primary with No Secondary
synchronized.
PwNS
2. Look at the CNB modules in the secondary chassis.
Front panel
If the display Then

shows
So check the following
Secondary CNB
!Cpt
1. All CNB modules in each redundant chassis are series D modules.
The CNB modules in the

primary and secondary
chassis dont match in
some way.
109
2. Each CNB module has a partner in the same slot in the other
redundant chassis.
3. Each pair of CNB modules (one in each chassis) is set to the same
node address.
4. Each module has compatible firmware.
5. All CNB modules in each redundant chassis are valid keepers. See
Update a Keeper Signature on page 110.
CMPT
Some module other than

this CNB module doesnt
match between the primary
and secondary chassis.
1. Each module has a partner in the same slot in the other redundant
chassis.
2. Each pair of controllers (one in each chassis) has the same memory
board (for example, 1756-L55M14).
3. Each module has compatible firmware.
4. The RSLogix 5000 project is configured for the right type of controller
and redundancy is enabled. See Configure a Controller for
Redundancy on page 72.
5. The Module Configuration window for the 1757-SRM module does
not list any reasons for the failure to synchronize. See See if an Edit
Session Is in Progresson page 111.
DUPL NODE
More than one device on

your ControlNet network is
using the same node
number.
1. No other device on the ControlNet network is set to the address of

the CNB modules plus one.
For example, if the CNB modules are set to 3, no other device should
be set to 4.
2. The 1757-SRCx cable is connected to both SRM modules.
NET ERR
The ControlNet media is

not completely connected.
All ControlNet taps, connectors, and terminators are connected.
110
Update a Keeper Signature Purpose

To see if the keeper signature of a CNB module is stopping the
secondary chassis from synchronizing
Secondary
When
Perform this procedure when a secondary chassis wont synchronize
and its CNB modules show !CPT.
!Cpt
Before You Begin

42797
The secondary chassis wont synchronize if the keeper signature of a

CNB module doesnt match its partner. This happens if you schedule
the ControlNet network while the secondary chassis is off or if the
CNB module was previously configured in a different network.
Actions
1. Start RSNetWorx for ControlNet software.
2. Has this network been scheduled before?
If
Then
No
A. From the File menu, select New.

B. From the Network menu, select Online.
C. Select your ControlNet network and choose OK.
Yes
A. From the File menu, select Open.

B. Select the file for the network and choose Open.
C. From the Network menu, select Online.
3. From the Network menu, choose Keeper Status.
4.
111
5.
Keeper Capable Node
Active Keeper Valid Keeper
offline file
N/A
N/A
01
No
No
02
Yes
Yes
4. Make sure the list contains all your keeper capable nodes. This
includes the CNB modules in the secondary chassis.
5. Make sure that each node has a valid keeper signature.
If the Valid Keeper column shows
Then
Yes
The node has a valid keeper signature.
No
Select the node and choose Update Keeper.
6. Choose Close.
See if an Edit Session Is in

Progress
Purpose
To see if a computer is stopping the secondary chassis from
synchronizing
Secondary
When
CMPT
Perform this procedure when a secondary chassis wont synchronize

and the CNB modules in the secondary chassis show CMPT.
42797
112
Actions
Actions
Details

primary chassis.

chassis.
2. Check the recent synchronization

attempts.
B. Do you see Edit Session In Progress under Recent
Synchronization Attempts?
Yes Go to step 3.
No An edit session didnt stop
synchronization. Return to Troubleshoot a
Failure to Synchronize on page 108.
3. Look for the reason.
If
Then
Another computer is editing the project in

the controller.
Stop the edit session.
The project contains test edits.
Untest the edits.
The Nonvolatile Memory Load/Store dialog

box of the controller is open.
Close the Nonvolatile Memory Load/Store

dialog box.
You tried to synchronize the chassis while

downloading a project at the same time.
Wait for the download to finish.
Actions
Details
4. Manually synchronize the chassis.
Choose Synchronize Secondary and then Yes continue with synchronization.
113
Interpret the SRM Event Log Purpose

To look through a log of events to see why the system switched over
or failed to synchronize
When
Perform this procedure when:
a switchover happens but your system synchronizes again.
youve already tried to use the hardware lights to find why your
system wont synchronize.
Before You Begin

The SRM clock is accurate only if you:
initially set it after you installed your system.
reset it after any power loss to both chassis.
114
Actions
Actions
Details

primary chassis.

2. Go to the event log.
Click Event Log.
Actions
Details
3. Look through the events of the secondary

chassis for a substantial change in log
times.
A. Start with the secondary chassis.
115
The lower list is the secondary chassis.

The cause of the switchover probably happened to secondary chassis while it was
the primary chassis.
B. Look for a change of months, days, or hours between the log times of events.
Sometimes the difference is only minutes.
The SRM logs only significant events. It doesnt log events while your system is
running normally.
C. Use the slot and module columns to find the module that caused the event.
D. Go to Interpret SRM events on page 117 to interpret the description.
Example
Heres a substantial change

in the log time.
The slot, module, and
description columns show
that the 1756-EWEB module
in slot 2 went lonely. That
usually means it lost its
network connection.
116
Actions
Details
4. Double-click and event for more

information.
A. Double-click an event to see if it gives more information.

The Extended Information Definition dialog opens.
B. Click OK when youre done to close the Extended Information Definition dialog.
Example
Someone removed the module for slot 2. Or the

module failed.
5. If the secondary log doesnt show the

cause, look at the primary log.
Sometimes you have to use both logs to find out what happened.
Example
A. The secondary log shows that something

happened around 15:40. But its not clear
just what happened.
B. The primary log shows that around that
time the partner SRM screamed. That
means it lost power.
117
Interpret SRM events

Use this table to interpret events recorded in the SRMs event log.
Event description
Meaning
Autoqualification Trigger
Something happened that caused the system to try and synchronize again. Double-click the
event to see what happened.
Blank Memories Rule
A check to choose a primary chassis if both chassis power up at the same time. Suppose
that the controllers in one chassis don't have projects while the controllers in the other
chassis do have projects. In that case, the other chassis becomes primary.
Chassis Modules Rule
that one chassis has more modules than the other chassis. In that case, the chassis with
the most modules gets the first chance to become primary. It becomes primary as long as
the other chassis isn't more able to control the system.
Chassis Redundancy State changed to
The chassis changed to a different redundancy state.

PwQS Primary with qualified (synchronized) secondary partner
QSwP Qualified (synchronized) secondary with primary partner
DSwP Disqualified secondary with primary partner
DSwNP Disqualified secondary with no partner
PwDS Primary with disqualified secondary partner
PwNS Primary with no secondary partner
Crossloading Error
A module isn't able to get some information to its partner.
Disqualified Secondaries Rule
that the modules in one of the chassis powered down in a disqualified secondary state. In
that case, the other chassis becomes primary.
Failed Modules Rule
that a module in one of the chassis is faulted but its partner module in the other chassis
isnt faulted. In that case, the other chassis becomes primary.
Firmware Error
The SRM has a problem.
Module Insertion
The SRM now sees the module on the backplane. This means the module has either just
powered up, just been put into the chassis, or just finished resetting. Double click the event
to see the slot number of the module.
Module Removal
The SRM no longer sees a module on the backplane. This means that the module either
experienced a nonrecoverable fault, was removed from the chassis, or was reset.
Double-click the event to see the slot number of the module.
Modules Chassis State Rule
that the modules in one chassis are already in a primary state. In that case, that chassis
becomes primary.
NRC Modules Rule
A check to choose a primary chassis if both chassis power up at the same time. NRC stands
for nonredundancy compliant. Suppose that a module in one of the chassis doesn't support
redundancy and all the modules in the other chassis do support redundancy. In that case,
the other chassis becomes primary.
118
Event description
Meaning
Partner not on same CNet link
A primary CNB isn't able to communicate with the secondary CNB over the ControlNet
network. This means there is either:
a network problem such as noise, a poor connection, or a problem with the termination.
a secondary CNB that isn't connected to the network.
Powerdown Time Rule
A check to choose a primary chassis if both chassis power up at the same time. If the two
chassis powered down more than one second apart, the last chassis to power down gets
the first chance at being primary.
Program Fault
A controller has a major fault.
SRM OS Error
The SRM has a problem.
SRM Serial Number Rule
A check to choose a primary chassis if both chassis power up at the same time. This is the
final tie-breaker. The SRM with the lower serial number gets the first chance to become
primary. It becomes primary as long as the other chassis isn't more able to control the
system.
Standby Secondaries Rule
A check to choose a primary chassis if both chassis power up at the same time. Since
standby isn't available yet, this check always ends in a tie.
SYS_FAIL_L Active
A module has a nonrecoverable fault or lost its connection to the network. When that
happens, the SYS_FAIL signal becomes true.
The backplane of the chassis has a SYS_FAIL signal. Each module in the chassis uses this
signal to indicate a problem.
The signal is normally false (inactive), which means that all modules in the chassis are
OK.
A module turns the SYS_FAIL signal true (active) when the module has a
nonrecoverable fault or it losses its connection to the network.
Look for later events to find out what happened.
If you see a Module Removal event shortly afterward, then a module has a
nonrecoverable fault. Double-click the Module Removal event to see the slot number of
the module. The SYS_FAIL signal may stay true until you cycle power or remove the
faulted module.
If you see a SYS_FAIL_L Inactive event within a few hundred milliseconds, then a cable
is probably disconnected or broken. A communication module pulses the SYS_FAIL
signal when the module loses its connection to the network. Look for a Transition to
Lonely event to see which module lost its connection.
The partner RM has been connected
The partner SRM powered up or become connected by the fiber-optic cable.
The partner RM screamed
The partner SRM lost power, has an unrecoverable fault, or was removed.
An SRM has circuits that hold power long enough for it to send a message to its partner
over the fiber-optic interconnect cable. The SRM sends the message even after you remove
it from the chassis. This message is called a scream. The scream lets the partner SRM tell
the difference between a broken fiber-optic interconnect cable and the power loss or
removal of the primary SRM.
If the fiber optic cable breaks, then there isn't a switchover.
If the SRM loses power or is removed, then there is a switchover.
119
Event description
Meaning
Transition to Lonely
A communication module doesn't see any other devices on its network. This usually means
that the network cable of the module is disconnected or broken. The event log shows
Transition to Not Lonely when you reconnect the cable.
Unknown Event
The SRM configuration tool doesn't have a description for the event.
WCT time change (> 1 second)
The clock of the SRM changed. This happens when you:

use the SRM configuration tool to set the clock.
connect the SRM to another SRM that is already primary. The SRM synchronizes its
clock to that of the primary SRM.
Export the SRM Event Log
Purpose
To export specific events from the SRM event log to a CSV or TXT file
When
look at the event log in spreadsheet software such as Microsoft
Excel.
send the event log to someone else.
Before You Begin

The SRM configuration tool lets you export events from both the
primary and the secondary chassis at the same time.
120
IMPORTANT
When you send event logs to Rockwell Automation:

send events from both the primary and secondary chassis.
include all events from the latest event to the last event
when you knew that the chassis were in a good state.
Actions
Action
Details

primary chassis.

chassis.
2. Go to the event log.
Click Event Log.
Action
121
Details
3. Select the events that you want to export. A. Click the first event that you want to export from the primary chassis.
B. Press and hold the [Shift] key and then click the last event that you want to export from
the primary chassis.
C. Repeat steps 3A and 3B for the secondary chassis.
4. Export your selection.
A. Choose Export Selection.
B. Click the Browse button and choose a location and

name for the export file.
C. Choose CSV (Comma-Separated Value).
D. Select the Include Extended Information check box.
E. Choose Export.
122
Manually Synchronize the

Chassis
After a switchover, you may have to manually synchronize the chassis

because either:
the Auto-Synchronization option is not set to Always or
the chassis failed to synchronize.
To manually synchronize the chassis:
1. Display RSLinx software.
2. From the Communications menu, choose RSWho.
3. Expand the network until you see the 1757-SRM module in the
primary chassis.
Workstation
+
AB_KTC-x, ControlNet
n, 1756-CNB/D/E
Backplane, 1756-Ax
xx, 1756 module, 1757-SRM
4. Right-click the 1757-SRM module and select

Module Configuration.
5. Click Synchronization.
6. Choose Synchronize Secondary and then choose Yes to confirm.

7. Choose OK.
123
8. In the primary chassis, what do the CNB modules display?

Front panel
If you see
Which means
PwQg
Primary with Synchronizing

(Qualifying) Secondary
Synchronization is in progress.
Primary with Synchronized

(Qualified) Secondary
The secondary chassis is synchronized.
Primary with Disqualified

Secondary
The secondary chassis is NOT synchronized.
Look here.
PwQS
PwDS
Then
Continue waiting. It may take several minutes
to synchronize the secondary chassis.
Skip the remaining steps in this section.
Go to step 9.
43130
9. Cycle power to the secondary chassis.

10. If the CNB module in the primary chassis fails to display PwQS,
see Troubleshoot a Failure to Synchronize on page 108.
Optimize Communication
If it takes too long to synchronize the secondary chassis or update

your HMI, there may not be enough controller time for unscheduled
communication. In general, unscheduled communication is any type
of communication that you do not configure through the I/O
configuration folder of the controller:
This type of communication
Is
Update I/O data (not including block-transfers)
Scheduled communication
Produce or consume tags

Communicate with programming devices (for
example, RSLogix 5000 software)
Unscheduled communication
Communicate with HMI devices

Execute Message (MSG) instructions, including
block-transfers
Respond to messages from other controllers
Synchronize the secondary controller of a redundant
system
Reestablish and monitor I/O connections, such as Removal
and Insertion Under Power conditions; this does not
include normal I/O updates that occur during the execution
of logic.
Bridge communications from the serial port of the
controller to other ControlLogix devices via the
ControlLogix backplane
124
To speed up unscheduled communication:

If an RSLogix 5000 project contains
Then
See Page
Only a continuous task and no other tasks

(This is the default task configuration.)
Choose a Greater System Overhead Time

Slice
124
More than one task (for example, at least 1

periodic task)
Make All Your Tasks Periodic
126
Choose a Greater System Overhead Time Slice

The system overhead time slice specifies the percentage of time
(excluding the time for periodic tasks) that the controller devotes to
unscheduled communication. The controller performs unscheduled
communication for up to 1 ms at a time and then resumes the
continuous task.
The following table shows the ratio between the continuous task and
unscheduled communication at various system overhead time slices:
At this time slice The continuous task
runs for
And unscheduled
communication occurs
for up to
10%
9 ms
1 ms
20%
4 ms
1 ms
33%
2 ms
1 ms
50%
1 ms
1 ms
At a system overhead time slice of 20 % (default), unscheduled

communication occurs every 4 ms of continuous task time for 1 ms.
Legend:
Task executes.
Task is interrupted (suspended).
1 ms
1 ms
1 ms
1 ms
1 ms
Unscheduled
communication
4 ms
Continuous task
4 ms
4 ms
4 ms
4 ms
125
If you increase the system overhead time slice to 33 %, unscheduled

communication occurs every 2 ms of continuous task time for 1 ms.
1 ms
1 ms
1 ms
1 ms
1 ms
1 ms
1 ms
1 ms
Unscheduled
communication
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
Continuous task
Enter a System Overhead Time Slice

To change the system overhead time slice:
1.
1. On the Online toolbar, click controller properties button.

2. Click Advanced.
2.
3.
3. Type or select a value for the system overhead time slice.

4. Choose
126
Make All Your Tasks Periodic

Action
Details
1. If you have more than one task, make

them all periodic tasks.
If the controller contains only a periodic task or tasks, the system overhead time slice value
has no effect. Unscheduled communication happens whenever a periodic task is not
running.
Example
Suppose your task takes 50 ms to execute and you configure its period to 80 ms. In that
case, the controller has 30 ms out of every 80 ms for unscheduled communication.
50 ms
50 ms
50 ms
periodic task
30 ms
30 ms
30 ms
unscheduled communication
2. Follow these guidelines to set the

periods of the tasks.
If you have multiple tasks, make sure that:

1. The execution time of a highest priority task is significantly less than its period.
2. The total execution time of all your tasks is significantly less than the period of the
lowest priority tasks.
This generally leaves enough time for unscheduled communication.
For example, in this configuration of tasks:
Task
Priority
Execution time
Rate
higher
20 ms
80 ms
lower
30 ms
100 ms
total execution time:
50 ms
1. The execution time of the highest priority task (Task 1) is significantly less than its
period (20 ms is less than 80 ms).
2. The total execution time of all tasks is significantly less than the period of the lowest
priority task (50 ms is less than 100 ms).
3. Tune the periods of the tasks.
Adjust the periods of the tasks as needed to get the best trade-off between executing your
logic and servicing unscheduled communication.
4. Look for overlaps.
Look at the Monitor tab of the properties of the task to see if overlaps are happening. An
overlap happens if the period of a task is less than its scan time. If you see overlaps,
increase the period of the task.
Check the Allocation of

Unused Memory
127
The controller reserves a specific amount of its unused memory for

tags and the rest for logic. Depending on how you configure the
memory usage, you might not have memory for the required
operation.
To display this dialog box:

1. Choose Edit Controller Properties.
2. On the Redundancy tab, choose the Advanced button.
If
Then
Important
OPC communications error or fail
Make sure the slider is not all the way to Tags.
You are unable to create tags while online
Make sure the slider is not all the way to Logic.
You are able to change this setting only

while:
You are unable to perform online edits
offline.
online in program mode.
Adjust CNB Usage
For each CNB module in a redundant chassis, keep CPU usage to less
than 75 percent.
Each redundant CNB module needs enough additional
processing time for redundancy operations.
At peak operations such as synchronization, redundancy uses an
additional 8 percent (approximately) of the CPU of the CNB
module.
A total CPU usage that is higher than 75 percent may prevent a
secondary chassis from synchronizing after a switchover.
To reduce the CPU usage of a module, take any of the following
actions:
Change the network update time (NUT) of the ControlNet
network (Typically, increase the NUT to reduce the CPU usage
of a CNB module.)
Increase the requested packet interval (RPI) of your connections.
Reduce the number of connections to (through) the CNB.
Reduce the number of MSG instructions.
Add another CNB module to each redundant chassis.
128
To obtain status information about a CNB module:

use RSLinx software.
look at the four-character display.
send a message to the CNB module.
Use RSLinx Software

2. Expand a network until the CNB module appears.
3. Right-click the module and choose Module Statistics.
4. Click Connection Manager.
Number of connections
used
CPU usage
42903
Look at the Four-Character Display

42797
The four-character display on the front of the 1756-CNB/D/E or

1756-CNBR/D/E module, shows the following information:
129
For this information about a

CNB module
Display
Where
Address of the module
A#xx
xx is the node address of the module.
Percent of CPU usage
%Cxx
xx is the percent of CPU usage. The range for the display is 00 - 99%.
Number of open connections
nCxx
xx is the number of open connections that the module is using.
Number of unconnected client

buffers
Ucxx
xx is the number of unconnected client buffers that the module is using. You see this
number only if the module is using 80% of its buffers or more. The module stops showing
the number if the number drops below 50%.
Number of unconnected server

buffers
Usxx
xx is the number of unconnected server buffers that the module is using. You see this
number only if the module is using 80% of its buffers or more. The module stops showing
the number if the number drops below 50%.
State of the modules keeper

function
Kpxx
xx is the state of the modules keeper function:

If xx is Then the module is
Ai
Active network keeper with either:

invalid keeper information
or
keeper signature that does not match the keeper signature of the network.
Av
Active network keeper with:

valid keeper information.
keeper signature that defines the keeper signature of the network.
Ii
Inactive network keeper with either:

invalid keeper information
or
keeper signature that does not match the keeper signature of the network.
Iv
Oi
Inactive network keeper with valid keeper information that matches the
keeper signature of the network.
Powering up with invalid keeper information
or
offline with invalid keeper information.
Ov
Powering up with valid keeper information that may or may not match the
keeper signature of the network
or
offline with valid keeper information that may or may not match the
keeper signature of the network.
Number of times that the

bandwidth of the module was
exceeded
Bxnn
nn is the number of times that the bandwidth of the module was exceeded (bandwidth
exceeded error) since the module was turned off or reset. You see this number only if the
number is more than zero.
130
Send a Message to the CNB Module

To use a Message (MSG) instruction to learn the CPU usage of a
CNB module, configure the MSG instruction as follows:
On this tab
For this
Type or select
Configuration
Message Type
CIP Generic
Service Type
Custom
Service Code
4f
Class
a1
Instance
Attribute
Source Element
Tag that uses a user-defined data type:

Members of the data type
Communication
Tag value
Name
Data type
offset
DINT
size_returned
INT
Source Length
Destination
INT tag in which to store the CPU usage of the CNB module
(0 - 99%.)
Path
1, slot_number
where:
slot_number is the slot number of the CNB module.
Change CNB modules from

Series D to Series E
131
Complete the following procedure to replace 1756-CNB/D or

1756-CNBR/D module(s) with series E modules.
IMPORTANT
Use this procedure only if your redundancy system is already at

revision 15.
Replace CNB modules with CNB modules and CNBR modules with
CNBR modules. Otherwise your chassis wont synchronize.
Finish this procedure once you start it.
Each module must be the same series as its partner in the other
redundant chassis. If you replace a module with a different series,
you must replace the partner module with the same series.
Before You Begin

This procedure is easier to complete if you first update the firmware
of your 1756-CNB/D or 1756-CNBR/D module(s).
If the CNB modules are
And you
Revision 11.1 or later

Not revision 11.1 or later
Then
Go to Actions and start the procedure. You dont need to update the
firmware of the modules.
Have a nonredundant
chassis with an open slot
1. Add the revision 11 EDS files for the CNB modules, if you havent
already done so.
2. Put one of the CNB modules into the open slot of the nonredundant
chassis.
3. Use ControlFlash software and update the firmware of the CNB module.
4. Remove the CNB module.
5. Repeat steps 1 thru 4 for the rest of the CNB modules.
6. Go to Actions and start the procedure.
Dont have a nonredundant

chassis with an open slot
Go to Actions and start the procedure. Youll have to use the secondary
chassis to update the modules.
132
Actions
Action
Details
1. Add the latest EDS files.
Add the revision 11 EDS files for the 1756-CNB and 1756-CNBR modules, if you havent
already done so,
2. Prepare the RSLogix 5000 project.
A. Start the RSLogix 5000 software and go online with the primary controller.
B. For each CNB/D/E or CNBR/D/E module in the local chassis, set the electronic keying
to compatible keying or disable keying and apply the changes.
C. Save the project.

primary chassis.

chassis.
Action
Details
4. Disqualify the secondary chassis,
133
B. Set Auto-Synchronization to Never.
C. Choose Apply and then Yes.

D. Click Synchronization.
E. Choose Disqualify Secondary and then Yes.
The secondary chassis

is disqualified.
F. Choose OK.
5. Did you already update the firmware of
the series E modules?
Did you already update the firmware of the series E modules?

Yes Go to step 7.
No Continue with step 6.
134
Action
Details
6. Update the firmware of the series E

modules.
A. Remove the 1757-SRM module from the secondary chassis.

B. Set the address of each series E module to the address of its corresponding series D
module plus one.
C. Replace each series D module with the corresponding series E module.
Important: Make sure you connect the correct ControlNet tap to each module.
D. Use ControlFlash software and update the firmware of each series E module.
E. Remove the series E modules from the secondary chassis and set their addresses to
match the original series D modules.
F. Repeat steps B thru E for the second set of series E modules.
G. Put the secondary SRM back into the secondary chassis.
H. Put one set of series E modules into the secondary chassis.
Important: Make sure that you use the correct address, slot, and ControlNet tap for
each module.
I. Go to step 8.
7. Replace the CNB modules in the

secondary chassis.
Replace the CNB modules in the secondary chassis with series E modules. As you replace
the modules:
make sure that you set each module to the same address as the module that its
replacing.
make sure that you connect the correct ControlNet tap. To avoid connecting the wrong
tap, replace the modules one at a time and reconnect the ControlNet tap.
Action
Details
8. Update the keeper signatures of the CNB

modules.
A. Start RSNetWorx for ControlNet and open the network configuration file.
135
B. Go online with the network. You dont have to browse the entire network.
C. Select Network > Keeper Status.
D. Select the node number of the secondary CNB and click Update Keeper.
E. Verify that the keeper signature has been updated.
F. Repeat steps D and E for the other CNB modules in the secondary chassis.
G. Click Close.
136
Action
Details
9. Reset the secondary CNB modules.
A. Cycle power to the secondary chassis.

B. On the Synchronization Status tab of the configuration tool, verify that the modules
show full compatibility.
10. Synchronize the secondary chassis.
B. Choose Synchronize Secondary and then Yes.

C. Wait for the chassis to synchronize.
The chassis are synchronized.

11. Initiate a switchover.
Choose Initiate Switchover and Yes.

12. Replace the CNB modules in the new
secondary chassis.
Repeat steps 7 thru 9 for the CNB modules in the new secondary chassis.
Action
Details
13. Synchronize the chassis.
A. Go to the SRM configuration tool for the primary chassis.
137
B. On the Configuration tab, change the Auto-Synchronization option to Always.
C. Choose Apply and Yes.

14. In the RSLogix 5000 project, change the
revision of the new local CNB modules to
revision 11.
Store or Load a Project

Using Nonvolatile Memory
Nonvolatile memory lets you keep a copy of your project on the

controller.
Term
Description
Nonvolatile memory
Memory of the controller that retains its contents while the

controller is without power or a battery.
Store
To copy a project to the nonvolatile memory of the controller.

This overwrites any project that is currently in the nonvolatile
memory.
Load
To copy a project from nonvolatile memory to the user memory

(RAM) of the controller. This overwrites any project that is
currently in the controller.
138
In a redundant system, store or load a project only while the

secondary chassis is disqualified.
Action
Details
Store a Project
Important: If your computer is online with the controller over a ControlNet network, check the
CPU usage of the CNB module. The CPU usage module must be less than about 75% for the store
to work.
1. Put the primary controller in program mode (program or remote program).
2. Open the Module Configuration properties for one of the 1757-SRM modules.
3. Set the Auto-Synchronization option to Conditional.
4. Disqualify the secondary chassis.
5. Store the project that is in the primary controller.
For step-by-step procedures on how to store a project, see Logix5000 Controllers Common
Procedures, publication 1756-PM001.
Important: Do not go back online to the primary controller until you complete the rest of the
steps in this procedure.
6. Go online to the secondary controller and store the project.
7. Return to the Module Configuration properties for one of the 1757-SRM modules.
8. Synchronize the controllers.
9. Set the Auto-Synchronization option to the desired option.
Load a ProjectUser Initiated

2. Go online to the primary controller.
3. In the primary controller, load the project.
For step-by-step procedures on how to store a project, see Logix5000 Controllers Common
Procedures, publication 1756-PM001.
4. Synchronize the controllers.
Load a ProjectOn Power Up
This Load Image option works the same as in a nonredundant system.

The controller loads the project on power up.
The controller loads the project before it activates the redundancy feature.
Load a ProjectOn Corrupt Memory
This Load Image option works the same as in a nonredundant system.

The controller loads the project when the memory is empty or corrupt.
The controller loads the project before it activates the redundancy feature.
Store a Project to
Nonvolatile Memory While
a Process Is Running
139
Complete the following procedure to store an updated project and

firmware to the nonvolatile memory of the controller. This procedure
lets you store a project while the process is running.
IMPORTANT
Use this procedure only with a 1756-L6x controller. Do not use

the nonvolatile memory of a 1756-L55M2x controller if youve
updated it to revision 15. Otherwise the controller will have an
unrecoverable fault (solid red OK light) and clear the project
from its memory.
Action
Details
1. Make sure the chassis are synchronized.
Synchronize the chassis if they arent already synchronized.
A. Open the SRM configuration tool for the primary chassis.

B. Set the Auto-Synchronization option to Never.
C. Disqualify the secondary chassis.
3. Store the secondary controllers project.
A. Go online to the secondary controller

B. Store the project to the nonvolatile memory of the secondary controller.
For step-by-step procedures on how to store a project, see Logix5000 Controllers
Common Procedures, publication 1756-PM001.
Important: Do not go back online to the secondary controller until you complete the
rest of the steps in this procedure.
A. Go to the SRM configuration tool.

B. Synchronize the chassis.
C. Initiate a switchover.
5. Store the new secondary controllers

project.
A. Go online to the new secondary controller

B. Store the project to the nonvolatile memory of the secondary controller.
For step-by-step procedures on how to store a project, see Logix5000 Controllers
Common Procedures, publication 1756-PM001.
Important: Do not go back online to the secondary controller until you complete this
procedure.

B. Set the Auto-Synchronization option to the desired option.
C. Synchronize the chassis.
140
Update a Module
Complete the following procedure to upgrade the revision of your

redundant modules. This procedure minimizes the time your process
is down during an upgrade.
IMPORTANT
Dont connect your computer to the network access port on a

CNB module in the primary chassis. Youll lose access to the
network when you turn off power to the chassis.
Action
Details
1. Upload and save the project.
A. Do you have an up-to-date copy of the project for the controller stored offline?
Yes Go to step 2.
No Continue with step B.
B. Upload the project in the primary controller.
C. Save the project.

secondary chassis.

chassis.
Action
Details
141
C. Choose Apply and then Yes to confirm.

E. Choose Disqualify Secondary and then Yes to confirm.

4. Upgrade the required firmware of the
secondary chassis.
See the ControlLogix Controller and Memory Board Installation Instructions, publication
1756-IN101.
5. Make the secondary controller the new

primary controller.
A. Start RSLogix 5000 software.

B. Download the project to the secondary controller.
C. When it is safe to stop the system, change the primary controller to Program Mode.
D. Turn off power to the primary chassis.
E. Go to the 1757-SRM properties of the secondary chassis.
F. Choose Become Primary.
142
Action
Details
6. Clear the fault of the new primary

controller.
A. In RSLogix 5000 software, go online to the new primary controller.

B. The controller is faulted. When a disqualified secondary controller becomes a primary
controller, the controller experiences a major fault.
C. From the Communications menu, choose Clear Faults.
D. To start control of the process, from the Communications menu, choose Run Mode.
7. Upgrade the other redundant chassis.
A. Turn on power to the other redundant chassis.

B. Upgrade the required firmware of the chassis.
8. Change the Auto-Synchronization Option

to ALWAYS.

B. On the Configuration tab, change the Auto-Synchronization option to Always.
C. Choose OK.
Update a System That Is

Already at Revision 13
Complete the following procedure to update the firmware of a

redundant chassis without shutting down the process:
IMPORTANT
Use this procedure only if your system is already at revision 13.

Do not use this procedure if:
your system is at revision 11 or earlier.
your system isnt operating yet.
During this procedure, you wont be able to use RSLogix 5000
software to change the mode of the controller. Use the keyswitch on
the front of the controller to change its mode.
Leave RSNetWorx for ControlNet software closed or offline
throughout this procedure. Otherwise, youll see errors in the
RSNetWorx software during the update process.
During this procedure:
Do not make any changes to the RSLogix 5000 project other than
the ones called out in this procedure.
Make sure no one else makes changes to the project.
Action
Details
1. Update the software
A. Go to the tool tray of your computer and shutdown RSLinx software.
143
B. Update the following software:

1. 1757-SRM System Redundancy Module Configuration tool
2. RSLogix 5000 software
3. RSLinx software
4. RSNetWorx software
5. ControlFLASH firmware update kit.
If youre planning to uninstall version 13 of your RSLogix 5000 software, wait until youve
completed and validated your update.
2. Add the latest EDS files.
Start Programs Rockwell Software RSLinx Tools EDS Hardware Installation

Tool
3. Put the keyswitches in the REM position.
Put the keyswitch of each redundant controller to the REM position. Otherwise you wont
be able to update the system.

primary chassis.

chassis.
144
Action
Details
C. Choose Apply and then Yes.

E. Choose Disqualify Secondary and then Yes.
The secondary chassis is

disqualified.
F. Choose OK.
6. Update the SRM module in the secondary
chassis.
A. Start the ControlFLASH firmware update tool.

B. Update the 1757-SRM module in the secondary chassis.
B. Choose Synchronize Secondary and then Yes.
The chassis are synchronized.
Action
145
Details
A. Choose Initiate Switchover and Yes.

B. Wait for the system to switchover.
The other chassis is now the

primary chassis.
9. Update the modules in the new
secondary chassis.
Use the ControlFLASH firmware update tool to update the modules in the new secondary
chassis.
10. Prepare the RSLogix 5000 project for the

update.
A. Start RSLogix 5000 software and go online to the primary controller.

B. Set the watchdog time for each task to this value or more:
Minimum watchdog time = (2 * maximum_scan_time) + 150 ms
where:
Maximum_scan_time is the maximum scan time for the entire task when the
secondary controller is synchronized.
C. Cancel or assemble any test edits.
D. Remove all SFC forces from the project.
E. Make sure that you dont need to make any changes to:
I/O Forces Once you start this procedure, you wont be able to disable or
enable I/O forces until you update both chassis.
I/O configuration
You can make those changes again when the update is done and both chassis
synchronize.
F. Save the project.
146
Action
Details
11. Change the project revisions.
A. Go offline.
B. Click the Controller Properties button.

C. Change the controller to the newer revision.
Example: Change the controller from revision 13 to revision 15.

D. Change the Revision of each local communication module to match what its revision
will be after you update its firmware.
Example: Suppose you plan to update the firmware of each CNB/D module in the
redundant chassis to revision 7.12. In that case, open the properties for each CNB/D
module in the chassis and set the revision to 7.12.
If you cant select the new revision, then change the electronic keying to either
compatible keying or disable keying.
147
Action
Details
12. Download the project to the secondary

controller.
Important: If I/O forces are enabled in the offline project, the software asks if you want to
enable the forces in the controller. Even if you choose No, I/O forces stay enabled in the
primary controller and become enabled in this controller after you switchover.
A. Use RSLogix 5000 software to download the project to the controller in the secondary
chassis. The secondary chassis has the higher network address of the redundant pair.
B. Go offline.
Important: Stay offline until you finish this procedure.
13. Lock the system for update.
Important: Do not abort a system lock. Otherwise, youll clear the project from the
B. Click System Update.
C. Choose Lock For Update and Yes.

D. Wait for the system to lock. It takes longer than a normal synchronization.
The system is locked.
148
Action
Details
14. Initiate a Locked Switchover.
A. Choose Initiate Locked Switchover and Yes.

B. Wait for the system to switchover. A locked switchover takes about as long as a
normal switchover.
The other chassis is now the

primary chassis.
15. Update the other redundant chassis.
Use the ControlFLASH firmware update tool to update the rest of the modules in the new
secondary chassis. Youve already updated the SRM module in this chassis.
A. Go to the SRM configuration tool for the primary chassis.

B. On the Configuration tab, change the Auto-Synchronization Option to ALWAYS.
C. Choose Apply and Yes.
The chassis synchronize.
D. Change the Date and Time in the SRM module.

E. Choose OK.
Appendix
Set Up EtherNet/IP Communication Across

Subnets
Purpose of This Chapter
To keep HMIs and messages pointing to the primary chassis when IP

swapping is not in use
Use this chapter when:

you want to use alias topics instead of IP swapping.
your primary and secondary chassis are on different EtherNet/IP
subnets.
If both redundant chassis are on
Then
Different subnets
You must point your HMIs and messages to

the new primary chassis after a switchover.
Use this appendix to show you how.
Router
Switch
Switch
Primary
chassis
Secondary
chassis
Same subnet
Switch
Primary
chassis
Secondary
chassis
Stop. Use IP swapping instead. This lets you

use the same IP address regardless of
which chassis is primary.
See Chapter 2.
When primary and secondary chassis are on different EtherNet/IP

subnets, they keep their IP addresses during a switchover. This means
that your and other controllers must be able to switch between the IP
address of each redundant chassis.
149
This chapter provides the following information:

Topic
Page
Keep an HMI Communicating with the Primary Chassis
150
Keep a Message Going to the Primary Chassis
156
150
Set Up EtherNet/IP Communication Across Subnets
Keep an HMI
Communicating with the
Primary Chassis
If youre not using IP swapping, your HMIs must direct their

communication to the new primary chassis after a switchover.
ControlLogix Redundancy Alias Topic Switcher software can most
easily do this. Look for this software on the CD along with your
firmware.
IMPORTANT
To use the ControlLogix Redundancy Alias Topic Switcher

software, your computer needs an activation file for RSLinx
software. The activation file lets you perform DDE/OPC
communication.
The ControlLogix Redundancy Alias Topic Switcher software works

with RSLinx alias topics. Together they keep your HMI communicating
with the primary controller after a switchover.
HMI tags In your HMI project, each tag references an
alias topic in RSLinx software. This lets RSLinx software
redirect communications to the appropriate chassis.
Xxxx Xx
012345
Alias topic In RSLinx software, an alias topic

represents a flexible communication path to one of
several controllers (topics).
In a ControlLogix redundancy system, the alias topic
points to the topic for the primary controller.
RSLinx
software
When a switchover occurs, the alias topic points to

the topic for the new primary controller.
Alias Topic
Topic for Chassis A
L E
5 N
5 B
Chassis A
Topic for Chassis B
L E
5 N
5 B
Chassis B
ControlLogix Redundancy Alias Topic Switcher software

Automatically reads a value in RSLinx software to
determine which controller is primary. It then commands
the alias topic to switch to the topic for that controller.
Topic In RSLinx software, a topic represents a

specific path to a controller. Since each ENBT
and EWEB module uses a unique IP address,
create a topic for the controller in each
redundant chassis.
151
To keep an HMI communicating with the primary chassis:

install the ControlLogix Redundancy Alias Topic Switcher
Software.
configure a Driver to Communicate with the Primary and
Secondary EtherNet/IP Modules.
create a DDE/OPC topic for each controller.
create an alias topic.
set up the alias topic switcher.
address the alias topic in the HMI project.
Install the ControlLogix Redundancy Alias Topic Switcher

Software
The ControlLogix Redundancy Alias Topic Switcher software
maintains communication between your HMI project and the primary
controller after a switchover.
To install the Alias Topic Switcher software, use the ControlLogix
Redundancy Alias Topic Switcher.Exe file. The file is located on the
same CD as the firmware for your redundancy system.
The Alias Topic Switcher software runs as a service. It starts
automatically when you start your computer and shows up in the tool
tray of your desktop.
ControlLogix Redundancy Alias

Topic Switcher
152
Configure a Driver to Communicate with the Primary and

Secondary EtherNet/IP Modules
2. Click
3. Select Ethernet devices and choose
4. Accept the default name.

5. Type the IP address of each ENBT or EWEB module.
To add another IP address, choose
6. Choose
7. Click
and then
.
Driver that you just added
Modules in the redundant chassis
153
Create a DDE/OPC Topic for Each Controller
1. Browse to the controller in Chassis A.

2. Right-click the controller and choose Configure New
DDE/OPC Topic.
3. Rename the topic to indicate that this is Chassis A.

4. Choose
update topic.)
and then
(Yes
5. Create a topic for the controller in Chassis B.
154
Create an Alias Topic

1. In RSLinx software, choose DDE/OPC
Alias Topic Configuration.
2. Type a name for the alias topic that will communicate with this pair of redundant controllers
3. Add the topic for each redundant controller to

the Aliased Topics list.
To add a topic, select the topic and choose
4. Select (check) the Switch on command check

box. Clear (uncheck) the remaining check boxes.
This lets the ControlLogix Redundancy Alias
Topic Switcher software control which topic the
alias topic uses for communication.
5. Choose
and then
155
Set Up the Alias Topic Switcher

IMPORTANT
If you start the Alias Topic Switcher software without access to

an RSLinx activation file (for example, without a version of
RSLinx which supports OPC), the following error occurs:
0x80040112
(The text for the message depends on your operating system.)
1. In the system tray, right-click the Redundancy Switch icon and choose Open Alias Topic Switching Tool.
2. In the Redundancy Alias Topic Switching Tool window, choose
3. Type the topic names:

a. Alias topic
b. Topic for the controller in Chassis A
Topic that the alias topic is currently using
156
Address the Alias Topic in the HMI Project
When you create tags for your HMI project, use the alias topic in the address of the tag.
Keep a Message Going to

the Primary Chassis
If youre not using IP swapping, any controller that sends a message

to a redundant chassis has to point to the new primary chassis after a
switchover.
L E
x N
B
T
IP Address A
L
5
5
M
IP Address B
L E
5 N
5 B
E
N
B
T
Chassis A
Primary
Chassis B
Switchover
Primary
In this procedure, use CIP Generic messages to determine which

chassis is primary. Then send a Message (MSG) instruction to the
primary controller.
L E
x N
B
MSG
Type - CIP Generic
L
5
5
M
157
E
N
B
T
Chassis A
MSG
Type - CIP Generic
L E
5 N
5 B
Chassis B
To keep a Message (MSG) instruction going to the new primary

chassis after a switchover:
create a periodic trigger for the messages.

obtain the redundancy state of chassis A.
obtain the redundancy state of chassis B.
determine which chassis is primary.
send the message to the appropriate controller.
Create a Periodic Trigger for the Messages

Free-running timer that triggers the execution of MSG instructions. The timer runs for 2 seconds (2000 ms) and then resets
and starts timing again. Every 2 seconds, Timer_RedundancyMSGs.DN = 1 for a single scan. The MSG instructions use this
bit as one of their conditions for execution.
Tag Name
Description
Alias For
Timer_RedundancyMSGs
Periodic trigger for the

execution of MSG
instructions. Triggers MSGs
every 2s.
Data Type
TIMER
158
Get the Redundancy State of Chassis A

If Timer_RedundancyMSGs.DN = 1 (2 seconds are up so execute the MSG instruction again)
And ChasA_GetRedundState_FromENBT.EN = 0 (The MSG instruction is not currently enabled.)
Then
Execute a MSG instruction that gets the redundancy state of Chassis A from the ENBT module in Chassis A. Store the
value in ChasA_RedundancyState (data type = DINT).
Tag Name
Description
Alias For
Periodic trigger for the execution of MSG

instructions. Triggers MSGs every 2s.
TIMER
ChasA_GetRedundState_FromENBT
Message instruction that gets the redundancy state

of Chassis A
MESSAGE
ChasA_RedundancyState
Redundancy state of the Chassis A:
DINT
2 = PwQS
3 = PwDS
4 = PwNS
MSG parameter
Value
Message Type
CIP Generic
Service Type
Get Attribute Single
Service Code
Class
c0
Instance
Attribute
Source Element
Data Type
MSG parameter
159
Value
Source Length
Destination
Path
(Communication tab)
Specify the 1756-ENBT module in Chassis A. Use either of the

following methods:
Add the module to the I/O configuration of the controller. Then
use the Browse button on the Communication tab to identify
the module.
Type the path using port numbers and addresses.
Get the Redundancy State of Chassis B

If Timer_RedundancyMSGs.DN = 1 (2 seconds are up so execute the MSG instruction again)
And ChasB_GetRedundState_FromENBT.EN = 0 (The MSG instruction is not currently enabled.)
Then
Execute a MSG instruction that gets the redundancy state of Chassis B from the ENBT module in Chassis B. Store the
value in ChasB_RedundancyState (data type = DINT).
Tag Name
Description
Alias For
Data Type
Periodic trigger for the execution of MSG

instructions. Triggers MSGs every 2s.
TIMER
ChasB_GetRedundState_FromENBT
Message instruction that gets the redundancy state

of Chassis B
MESSAGE
ChasB_RedundancyState
Redundancy state of the Chassis B:
DINT
2 = PwQS
3 = PwDS
4 = PwNS
160
MSG parameter
Value
Message Type
CIP Generic
Service Type
Get Attribute Single
Service Code
Class
c0
Instance
Attribute
Source Element
Source Length
Destination
Path
(Communication tab)
Specify the 1756-ENBT module in Chassis B. Use either of the

following methods:
Add the module to the I/O configuration of the controller. Then
use the Browse button on the Communication tab to identify
the module.
Type the path using port numbers and addresses.
161
Determine Which Chassis is Primary

If ChasA_RedundancyState = 2, 3, or 4 then
ChasA_IsPrimary = 1. (Chassis A is the primary chassis.)
If ChasB_RedundancyState = 2, 3, or 4 then
ChasB_IsPrimary = 1. (Chassis B is the primary chassis.)
Tag Name
Description
Redundancy state of the Chassis A:
Alias For
Data Type
DINT
2 = PwQS
3 = PwDS
4 = PwNS
Redundancy state of the Chassis B
DINT
2 = PwQS
3 = PwDS
4 = PwNS
162
Tag Name
Description
Alias For
Data Type
ChasA_IsPrimary
If set (1), then Chassis A is the primary chassis.
IsPrimary.0
BOOL
ChasB_IsPrimary
If set (1), then Chassis B is the primary chassis.
IsPrimary.1
BOOL
IsPrimary
Each bit represents the primary status for an

individual chassis within a redundant chassis pair.
1 = primary.
0 = not primary.
A single DINT tag for all the chassis uses less
memory than a unique tag for each chassis.
Send the Message to the Appropriate Controller

If Timer_RedundancyMSGs.DN = 1 (2 seconds are up.)
And ChasA_IsPrimary = 1. (Chassis A is the primary chassis.)
And ChasA_MSG.EN = 0 (The message is not currently enabled.)
Then
Execute the MSG instruction for the controller in Chassis A.
DINT
163
If Timer_RedundancyMSGs.DN = 1 (2 seconds are up.)

And ChasB_IsPrimary = 1. (Chassis B is the primary chassis.)
And ChasB_MSG.EN = 0 (The message is not currently enabled.)
Then
Execute the MSG instruction for the controller in Chassis B.
Tag Name
Description
Alias For
Data Type
ChasA_IsPrimary
If set (1), then Chassis A is the primary chassis.
IsPrimary.0
BOOL
ChasA_MSG
Message instruction that transfers data between this

controller and the controller in redundant Chassis A
ChasB_IsPrimary
If set (1), then Chassis B is the primary chassis.
ChasB_MSG
Message instruction that transfers data between this

controller and the controller in redundant Chassis B
MESSAGE
IsPrimary.1
BOOL
MESSAGE
164
Notes:
Appendix
Convert an Existing System to Redundancy
Introduction
If you are adding redundancy to an existing system, follow these

guidelines:
Changing the node number of a CNB module may affect
messages, tags, or listen-only connections in other devices.
Choose node numbers that have the least impact on existing
communications.
An existing system that contains local I/O modules still requires
two additional chassis.
A redundant system can use only I/O that is in a remote
chassis (for example, not in the same chassis as the
controller).
We recommend that you move the existing 1756-L55Mxx
controller from the original chassis and place it in a redundant
chassis.
Change any event tasks to periodic tasks. You cant use event
tasks in a ControlLogix redundancy system.
Convert Local Modules to

Remote Modules
If you are converting an existing system to a redundant system:

And the system
Then
Contained only I/O modules that

were not in the same chassis as
the controller
Do not change the I/O configuration of the controller.
Contained local I/O modules
Use the procedures in this section to convert the

configuration of local modules to remote modules.
To convert a local module to a remote module:

reconfigure the local I/O modules.
replace local I/O tags.
replace any aliases to local I/O tags.
165
166
Reconfigure the Local I/O Modules

1. If you have not already done so, add the CNB module of the
remote chassis to the I/O configuration of the controller. See the
ControlLogix System User Manual, publication 1756-UM001.
I/O Configuration
[x] 1756-xxx name_of_local_module
Cut local I/O modules from here.
[x] 1756-CNB/x name_of_local_CNB

z [x] 1756-CNB/x name_of_remote_CNB
Paste the I/O modules

here.
2. In the controller organizer, cut the modules from the local I/O
configuration and paste them into the remote CNB module. Cut
and paste the following modules:
I/O
1756-DHRIO
1756-DNB
1756-ENET or -ENB
1756-MVI
Replace Local I/O Tags

1. Open a routine. If a routine is already open, click within the
routine to activate the window.
2. Press the Ctrl + H keys.
167
4
5
6
42804
3. Type Local.
4. Type the name of the CNB module that is in the remote chassis.
5. Select All Routines.
6. Choose Find Within >>.
42805
7. Select Ladder Diagram.

8. Check Instruction Operands.
9. Choose Replace All.
The Search Results tab displays the changes to the logic.
168
10. Choose Close.

The following example shows the results of replacing Local with
chassis_c.
Replacing "Local" with "chassis_c"...
EXAMPLE
Searching through MainProgram - MainRoutine...

Replaced: Rung 0, XIC, Operand 0: XIC(Local:16:I.Data.0)
Replaced: Rung 0, OTE, Operand 0: OTE(Local:2:O.Data.0)
Replaced: Rung 8, OTE, Operand 0: OTE(Local:15:O.CommandRegister.Run)
Complete - 7 occurrence(s) found, 7 occurrence(s) replaced.
Replace Any Aliases to Local I/O Tags

Are any tags aliases for I/O devices that were previously in a local
chassis?
If
Then
Yes
Go to step 1.
No
Skip this procedure.
1. From the Logic menu, choose Edit Tags.

2. Press the Ctrl + H keys (replace).
169
4
5
6
42815
3. Type Local.
4. Type the name of the CNB module that is in the remote chassis.
5. Select All Tags.
6. Choose Find Within >>.
42815
7. Check Alias.
8. Choose Replace All.
9. Choose Close.
170
Notes:
Appendix
Attributes of the Redundancy Object
Use the redundancy object to learn about the status of your

redundancy system.
Get this attribute
Data
type
GSV/SSV
Description
Redundancy status of the

entire chassis
ChassisRedundancy
State
INT
GSV
If
Then
16#1
Power up or undetermined
16#2
Primary with synchronized secondary
16#3
Primary with disqualified secondary
16#4
Primary with no secondary
If
Then
16#8
Synchronized secondary
16#9
Disqualified secondary with primary
16#E
No partner
If
Then
16#1
Power up or undetermined
16#2
Primary with synchronized secondary
16#3
Primary with disqualified secondary
16#4
Primary with no secondary
16#6
Primary with synchronizing secondary
If
Then
16#7
Synchronizing secondary
16#8
Synchronized secondary
16#9
Disqualified secondary with primary
16#E
No partner
If
Then
Undetermined
No compatible partner
Fully compatible partner
Redundancy state of the

partner chassis
Redundancy status of the

controller
Redundancy state of the

partner
Results of the compatibility

checks with the partner
controller
171
PartnerChassis
RedundancyState
ModuleRedundancy
State
PartnerModule
RedundancyState
INT
INT
INT
CompatibilityResults INT
GSV
GSV
GSV
GSV
172
Get this attribute
Data GSV/SSV
type
Description
Status of the
synchronization
(qualification) process
Qualification
InProgress
INT
If
Then
-1
Synchronization (qualification) is not in progress.
Unsupported
1 - 99
For modules that can measure their completion

percentage, the percent of synchronization
(qualification) that is complete.
50
For modules that cannot measure their completion

percentage, synchronization (qualification) is in
progress.
100
Synchronization (qualification) is complete.
If
Then
One of the following:
Keyswitch settings of the

controller and its partner
match or do not match
KeyswitchAlarm
DINT
GSV
GSV
The keyswitches match.

No partner is present.
Position of the keyswitch of
the partner
Status of the minor faults of

the partner (if the
ModuleRedundancyState
indicates that a partner is
present)
PartnerKeyswitch
PartnerMinorFaults
DINT
DINT
GSV
GSV
Keyswitches do not match
If
Then the keyswitch is in
Unknown
RUN
PROG
REM
This
bit
Means this minor fault
Problem with an instruction (program)
Periodic task overlap (watchdog)
Problem with the serial port
10
Low battery
Get this attribute
Data
type
GSV/SSV
Description
Mode of the partner
PartnerMode
DINT
GSV
If
Then
16#0
Power up
16#1
Program
16#2
Run
16#3
Test
16#4
Faulted
16#5
Run-to-program
16#6
Test-to-program
16#7
Program-to-run
16#8
Test-to-run
16#9
Run-to-test
16#A
Program-to-test
16#B
Into faulted
16#C
Faulted-to-program
If
Then
Unknown
Chassis A
Chassis B
In a pair of redundant
chassis, identification of a
specific chassis without
regard to the state of the
chassis.
PhysicalChassisID
INT
GSV
173
174
Get this attribute
Data GSV/SSV
type
Slot number of the

1757-SRM module in this
chassis
SRMSlotNumber
INT
GSV
DINT
GSV
Size of the last crossload LastDataTransfer

Size of the last crossload Size
if you had a secondary
chassis
Description
This attribute gives the size of data that was or would have
been crossloaded in the last scan.
Yes This gives number of DINTs that was crossloaded in
the last scan.
No This gives number of DINTs that would have been
crossloaded in the last scan.
Size of the biggest

crossload
MaxDataTransfer
Size
Size of the biggest

crossload if you had a
secondary chassis
DINT
GSV
SSV
This attribute gives the biggest size of the LastDataTransfer

Size attribute.
To reset this value, use an SSV instruction with a Source
value of 0.
Yes This gives biggest number of DINTs that was
crossloaded.
No This gives biggest number of DINTs that would have
been crossloaded.
Appendix
If You Have Series B ControlNet Bridge

Modules
About This Appendix
This appendix describes several situations that could happen if you

use series B of a ControlNet Bridge module:
Topic
Page
Communication Loss If You Bridge Through a Series B ControlNet Bridge Module 175
Communication Could Stop If You Use a Series B ControlNet Bridge Module
177
Communication Loss if You Situation

Bridge Through a Series B
could temporarily lose communication with a remote chassis if
ControlNet Bridge Module You
you use both these modules in the remote chassis:
1756-CNB/B or 1756-CNBR/B module
1756-DHRIO module that is connected to a remote I/O network.
175
176
If You Have Series B ControlNet Bridge Modules
L C
5 N
5 B
M
x
S
R
M

Remote chassis
C
N
B/
B
Other modules
D
H
R
I
O
Remote I/O
IMPORTANT
On the first switchover after you download a project to the controller, you may
temporarily lose communications with these devices
The loss of communication happens on the first switchover after you

download the project to the redundant controller.
You lose communication with the remote chassis and any
devices to which you were bridging via the chassis, such as the
remote I/O modules.
During the communication loss, the I/O modules go to their
configured state for a communication fault.
The communication loss is temporary. Communications restore
themselves.
Prevention
To prevent this situation, use series D ControlNet Bridge modules.
177
Communication Could Stop Situation

If You Use a Series B
communication on a ControlNet network could stop if the lowest
ControlNet Bridge Module All
node is a 1756-CNB/B or 1756-CNBR/B module. This happens if you
unplug or break the tap of the module while it is turned on.
Corrective Action
If
Then
Tap of a series B ControlNet Bridge module

becomes unplugged or broken.
1. Turn off the power to the module.

2. Replace the tap.
3. Turn on the power to the module.
Communication on the network stops

because of an unplugged or broken tap.
Cycle power to each primary controller on

the network.
Prevention
To prevent this situation, use series D ControlNet Bridge modules.
178
Restriction
Description
Communication Loss When Bridging

Through a Series B ControlNet Bridge
Module
You could temporarily lose communication with a remote chassis if you use both these modules in
the chassis:
1756-DHRIO module that is connected to a remote I/O network.
L C
5 N
5 B
M
x
S
R
M

Remote chassis
C
N
B
/
B
D
H
R
I
O
Other modules
Remote I/O
IMPORTANT
On the first switchover after you download a project to the controller, you may
temporarily lose communications with these devices
The loss of communication occurs on the first switchover after you download the project to the
redundant controller.
You lose communication with the remote chassis and any devices to which you were bridging
via the chassis, such as the remote I/O modules.
During the communication loss, the I/O modules go to their configured state for a
communication fault.
The communication loss is temporary. Communications restore themselves.
To prevent this situation, use 1756-CNB/D/E or 1756-CNBR/D/E modules.
Restriction
Description
If the Lowest Node Is a 1756-CNB/B

or -CNBR/B Module, Removing a Tap
or Breaking a Cable Could Stop All
Communications over the Network
If the lowest node on a ControlNet network is a 1756-CNB/B or 1756-CNBR/B module, all

communications over the network could stop if:
179
a tap to the 1756-CNB/B or -CNBR/B module is disconnected or breaks and then is replaced
while power is still applied to the 1756-CNB/B or -CNBR/B module
If a tap to a 1756-CNB/B or -CNBR/B module becomes disconnected or broken, take these actions:
1. Turn off the power to the 1756-CNB/B or -CNBR/B module.
2. Replace the tap.
If a communication failure occurs because of a disconnected or broken tap, cycle power to each
primary controller on the network.
To prevent this situation, use a 1756-CNB/D/E or -CNBR/D/E module as your lowest node on the
network.
180
Notes:
Appendix
Proper Use of an
EtherNet/IP Network
For EtherNet/IP communication and messaging, keep the following

restrictions in mind:
IMPORTANT
In a redundant system, use an EtherNet/IP network only for

HMI/workstation communication and messaging.
Do not use an EtherNet/IP network for:
communication with I/O modules.
communication between devices via produced/consumed
tags.
Restriction
Details
Dont use ControlLogix5564 controllers.
You cant use this revision with 1756-L64 controllers.
Dont use 1756-CN2 modules in a redundant

chassis.
You cant use this revision with 1756-CN2 ControlNet bridge modules in a redundant
chassis.
Dont use equipment phases.
This revision wont let you download a project that has equipment phases or create
equipment phases online.
Dont use this revision to update a

revision 11 or earlier system.
Use this revision only if your redundant chassis are already updated to revision 13 or arent
in operation yet
Dont use the nonvolatile memory of a

ControlLogix5555 controller.
Dont use the nonvolatile memory of a 1756-L55M2x controller. This includes storing a
project to nonvolatile memory and loading it from nonvolatile memory. Otherwise the
controller will have an unrecoverable fault (solid red OK light) and clear the project from its
memory.
Lgx00068091
181
182
Restriction
Details
Always keep the controller unlocked.
Make sure the controller stays unlocked.
Dont lock the controller.
A redundancy system automatically unlocks a locked controller during a switchover. But

the workstation that locked the controller doesnt show the change. The workstation
continues to show that the controller is locked even though it isnt. Once the controller is
unlocked, multiple workstations can edit the project in the controller.
Lgx00067869
Revision 2.6 or later of the SRM
configuration tool doesnt work with revision
11 or earlier systems.
Revision 2.6 or later of the 1757-SRM System Redundancy Module Configuration tool
doesnt work with revision 11 or earlier redundancy systems. You can cause the 1757-SRM
module to fault.
Use revision 2.6 or later of the configuration tool only with revision 13 or later
ControlLogix redundancy systems.
RSLinx software version 2.43 or later automatically installs version 2.6 or later of
the configuration tool.
To connect to a revision 11 or earlier redundancy system, uninstall the
configuration tool and install a compatible version. Use version 2.5 of the
configuration tool for revision 11 redundancy systems.
Make sure your ENBT modules are catalog
revision E01 or later.
To use a 1756-ENBT module in a redundant controller chassis, make sure its catalog
revision is E01 or later. Otherwise, the secondary chassis wont synchronize with the
primary chassis.
ControlLogix
Ethernet/IP 10/100
CAT. NO./SERIES
CAT. REV.
1756-ENBT
E01
To find the catalog revision of a module,

look at the label on the side of the
module or box.
Catalog revision
Example: Use a catalog revision, such as E01, E02, or F01.
Restriction
Details
For a series B controller with 1.7 firmware,

use a nonredundant chassis to update it the
first time.
Example
183
You just took the controller out of its box. Its label shows that it is a series B controller
with 1.7 firmware, as in the following example:.
1.7
F/W REV.
LOGIX 5563
PROCESSOR UNIT
CATALOG / SERIES
CATALOG REV.
1.7
PART NO.
1756-L63 B
In this case:
1. Put the controller in a nonredundant chassis.
2. Update the controller.
3. Put the controller in the redundant chassis.
Otherwise, the controller will have a an unrecoverable fault.
After you update it the first time, you can update it in the redundant chassis from then on.
Nonexample
The controller is already running in your system. You want to update it to a later revision.
In this case, leave it where it is and update it there.
Give an SRM module several minutes or
more to update.
It takes several minutes to update a 1757-SRM module and the module resets itself at
least 4 times. An SRM module with 3.37 or earlier firmware may become inoperative if
you interrupt the update process.
Wait until you see this box

turn green and say Update
complete.
If the update fails, leave the power on and try again. The update failed if you see:
Update Status window turn red and say the update failed.
OK LED on the SRM module is red flashing and the 4-character display is blank.
Wait at least 45 seconds after the redundant
chassis are disqualified before you try to
synchronize them
If your secondary chassis becomes disqualified or you manually disqualify it, do these
actions before you try to synchronize the chassis:
Make sure the synchronization status of the primary modules is full compatibility.
Wait at least 45 seconds before you give the command to synchronize the
secondary chassis.
184
Restriction
Details
If you unplug the fiber optic cable between

the SRM modules, wait until they stabilize
before you reconnect it
If you unplug the fiber optic cable between the 1757-SRM modules, check the
synchronization status of the secondary SRM module before you reconnect the cable. Wait
until its status is secondary with no partner. You can reconnect the cable once the module
is in that state. Otherwise, the secondary SRM could fault with EA91 error.
Index
Numerics
1756-ENBT module
See ENBT module
1756-EWEB module
EWEB module
1756-HYD02 20
1756-L60M03SE 21
1756-M02AE 21
1756-M02AS 21
1756-M03SE 21
1756-M08SE 21
1756-M16SE 21
1757-SRC cable
lengths 32
1757-SRM module
See SRM module
A
auto-synchronization 65
B
BSL instruction 85
BSR instruction 85
C
change
CNB modules from series D to series E
131
chassis
assign a chassis as primary 15
install 47
clock
SRM module 61, 94
CNB module
4 character display 128
addresses during a switchover 19
connection 37
install 48
requirements 22, 31
statistics 127
usage 127
CNB modules
changing from series D to series E 131
communication
optimize 123
compatible software versions
redundant system 26
configure
controller 72
EtherNet/IP module 52
I/O 74
SRM module 55
connection 37
consumed tag
configure 74
controller
configure 72
connection 37
download project 98
install 48
nonvolatile memory 137
periodic task 126
program scan time 77, 79
project 69
requirements 22, 31
synchronize 53, 122
system overhead time slice 124
watchdog time 102
ControlLogix5555 controller 22
ControlNet network
assign addresses 37
general lay-out 30
guidelines 37
keeper signature 100, 110
redundant media 35
schedule 98
conversion
to redundant system 165
corrected anomalies
redundancy revision 15.56 27
crossload 16, 18
estimate time for 77
D
data
crossload 18
integrity 85
DeviceNet network
design 21, 33
disqualified
overview 16
troubleshoot 106
download 98
E
edit
edit online 18, 69
186
Index
edit session in progress

troubleshoot 111
ENBT module
configure 52
requirements 23
enhancements
redundancy revision 15.56 26
estimate program scan time 77
EtherNet/IP network
alias topics 149
configure modules 52
design 21, 33, 40
guidelines 40
IP swapping 20
module requirements 23
proper use 181
without IP swapping 149
event log
export 119
interpret 113
event task 20
EWEB module
configure 52
requirements 23
export
event log 119
F
FFU instruction 85
finalize
online edits 71
firmware
update 53, 140
firmware combinations
redundant system 14
G
Get System Value instruction 90, 171
GSV instruction 90, 171
H
HMI
configure tags 76
design guidelines 30, 34
optimize communication 123
switch between topics 149
I
I/O
configure 74
convert local to remote 165
placement 21, 33, 51
redundant power supplies 36
import
event log 119
inhibit a task 20
install
system components 45
IP address
assign 52
IP swapping 40
manage without IP swapping 149
what happens during a switchover 20
IP swapping
overview 20
K
keeper signature
check 100
update 110
L
load
project from nonvolatile memory 137
M
message
configure 76
instruction 76
send to SRM module 94
Microsoft Excel
import event log 119
motion 20
MSG instruction 76
N
NAP 16
network access port
restrictions 16
network update time
guidelines 37
nonvolatile memory
load a project 137
store a project 137
Index
O
online edits
during a switchover 18
finalize 71
plan for 69
operator interface
design guidelines 34
P
PanelView terminal
design guidelines 30, 34
periodic task 126
power supplies
redundant 36
primary chassis
assign a chassis as primary 15
produced tag
configure 74
program
finalize online edits 71
number of 79
program scan time
estimate crossload time 77
minimize 79
overview 18
project
create and maintain 69
download 98
edit online 18
load 137
store 137
project storage
storing while process is running 139
proper use
EtherNet/IP network 181
Q
qualify. See synchronize
R
REDUNDANCY object 171
redundancy revision 15.56
corrected anomalies 27
enhancements 26
redundant system
compatible software versions 26
firmware combinations 14
restrictions 181
remote I/O network
187
design 21, 33
requested packet interval 74
restrictions
redundant system 181
revision 13
updating system 142
RIO network
design 21, 33
S
scan time
See program scan time, task scan time
schedule a ControlNet network 98
secondary chassis
troubleshoot 106
SRM configuration tool
find the revision 57
open 55
SRM module
auto-synchronization 65
configure 55
enable program control 66
export event log 119
install 48
interpret event log 113
program control 66
send message to 94
set the clock 61, 94
synchronization status 63
synchronize controllers 122
status
of my redundancy system 90
store
project to nonvolatile memory 137
project to nonvolatile memory while
process is running 139
switchover
causes 15
data integrity 85
diagnose cause 106
run code after 91
test 63
trigger with MSG instruction 94
troubleshoot 106
what happens to network addresses 19,
20
what happens to online edits 18
synchronize
controllers 122
diagnose failure 106
overview 16
status 63
188
Index
synchronize controllers 53
system information
get 90, 171
system overhead time slice 124
T
task
event 20
inhibit 20
number of 126
watchdog time 102
test
switchover 63
test edits
finalize 71
what happens during a switchover 18, 69
troubleshoot
switchover 106
U
update
system that is already at revision 13 142
update firmware 53, 140
W
watchdong time 102
workstation
connect to a NAP 16
How Are We Doing?

Your comments on our technical publications will help us serve you better in the future.
Thank you for taking the time to provide us feedback.
You can complete this form and mail it back to us, visit us online at www.ab.com/manuals, or
email us at [email protected]
Pub. Title/ ControlLogix Redundancy System
Type
Cat. No.
1756-CNB/D, 1756-CNBR/D, 1756-ENBT, 1756-EWEB, Pub. No. 1756-UM523F-EN-P Pub. Date September 2006 Part No. 953030-15
1756-L55, 1756-L55M12, 1756-L55M13, 1756-L55M14,
1756-L55M16, 1756-L55M22, 1756-L55M23,
1756-L55M24, 1756-L61, 1756-L62, 1756-L63,
1757-SRM
Please complete the sections below. Where applicable, rank the feature (1=needs improvement, 2=satisfactory, and 3=outstanding).
Overall Usefulness
Completeness
(all necessary information
is provided)
Technical Accuracy
(all provided information
is correct)
How can we make this publication more useful for you?
Clarity
1
(all provided information is
easy to understand)
Other Comments
Can we add more information to help you?

procedure/step
illustration
feature
example
guideline
other
explanation
definition
Can we be more accurate?

text
illustration
How can we make things clearer?
You can add additional comments on the back of this form.
Location/Phone
Your Name
Your Title/Function
Would you like us to contact you regarding your comments?

___No, there is no need to contact me
___Yes, please call me
___Yes, please email me at __________________________
___Yes, please contact me via ________________________
Return this form to:
Allen-Bradley Marketing Communications, 1 Allen-Bradley Dr., Mayfield Hts., OH 44124-9705

Phone: 440-646-3176 Fax: 440-646-3525 Email: [email protected]
Publication ICCG-5.21- January 2001
PN 955107-82
PLEASE FASTEN HERE (DO NOT STAPLE)
PLEASE FOLD HERE
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL

FIRST-CLASS MAIL PERMIT NO. 18235 CLEVELAND OH
POSTAGE WILL BE PAID BY THE ADDRESSEE
1 ALLEN-BRADLEY DR
MAYFIELD HEIGHTS OH 44124-9705
PLEASE REMOVE
Other Comments
Rockwell Automation
Support
Rockwell Automation provides technical information on the web to assist you

in using our products. At http://support.rockwellautomation.com, you can
find technical manuals, a knowledge base of FAQs, technical and application
notes, sample code and links to software service packs, and a MySupport
feature that you can customize to make the best use of these tools.
For an additional level of technical phone support for installation,
configuration and troubleshooting, we offer TechConnect Support programs.
For more information, contact your local distributor or Rockwell Automation
representative, or visit http://support.rockwellautomation.com.
Installation Assistance
If you experience a problem with a hardware module within the first 24
hours of installation, please review the information that's contained in this
manual. You can also contact a special Customer Support number for initial
help in getting your module up and running:
United States
1.440.646.3223
Monday Friday, 8am 5pm EST
Outside United
States
Please contact your local Rockwell Automation representative for any

technical support issues.
New Product Satisfaction Return

Rockwell tests all of our products to ensure that they are fully operational
when shipped from the manufacturing facility. However, if your product is
not functioning and needs to be returned:
United States
Contact your distributor. You must provide a Customer Support case

number (see phone number above to obtain one) to your distributor in
order to complete the return process.
Outside United
States
Please contact your local Rockwell Automation representative for

return procedure.
Back Cover
Publication 1756-UM523F-EN-P - September 2006 2

Supersedes Publication 1756-UM523E-EN-P - May 2005
PN 953030-15
Copyright 2006 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

Redundancy PDF

Uploaded by

Copyright:

Available Formats

Redundancy PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Redundancy PDF

Uploaded by

Copyright:

Available Formats

ControlLogix

Important User Information

Solid state equipment has operational characteristics differing from those of

Identifies information about practices or circumstances that can cause

Identifies information that is critical for successful application and

Labels may be located on or inside the equipment, for example, a drive

Labels may be located on or inside the equipment, for example, a drive

This release of this document contains new and updated information.

The document contains the following changes:

Series E information for 1756-CNB and -CNBR modules

Redundant System Firmware Combinations

Compatible Software Versions

Enhancements in Revision 15.56

Corrected Anomalies in Revision 15.56

Restrictions and Known Anomalies

Update a System That Is Already at Revision 13

Store a Project to Nonvolatile Memory While Process Is Running

Change CNB Modules from Series D to Series E

Publication 1756-UM523F-EN-P - September 2006

Publication 1756-UM523F-EN-P - September 2006

Whats in This Chapter? . . . . . . . . . . . . . . . . . . . . . . . . . . . .

How to Use This Chapter . . . . . . . . . . . . . . . . . . . . . . .

When to Use This Chapter. . . . . . . . . . . . . . . . . . . . . . . . . . 45

Publication 1756-UM523F-EN-P - September 2006

How to Use This Chapter . . . . . . . . . . . . . . . . . .

Change the Program Control Option

When to Use This Chapter. . . . . . . . . . . . . . . . . . . . . . .

Publication 1756-UM523F-EN-P - September 2006

Before You Begin . . . . . . . . . . . . . . . . . . . .

When to Use This Chapter. . . . . . . . . . . . . . . . . . .

Publication 1756-UM523F-EN-P - September 2006

Use RSLinx Software . . . . . . . . . . . . . . . . . . . .

Purpose of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Publication 1756-UM523F-EN-P - September 2006

About This Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

Publication 1756-UM523F-EN-P - September 2006

Proper Use of an EtherNet/IP Network . . . . . . . . . . . . . . . 181

Purpose of this Manual

This manual guides the design, development, and implementation of a

Who Should Use this

This manual is intended for those in the following professions who

When to Use This Manual

Use this manual throughout the lifecycle of a redundancy system. The

How to Use this Manual

The actual name of an item that you Right-click User-Defined

Right-click on the item that is named

Information that you must supply

You must identify the specific program in

Press the Enter key.

Enclosed in brackets A keyboard key.

Publication 1756-UM523F-EN-P - September 2006

This table lists ControlLogix products and documentation that may be

ControlLogix ControlNet Bridge Module Installation Instructions

ControlLogix ControlNet Interface Module Release Notes

ControlLogix ControlNet Bridge Module, Series E Installation Instructions

ControlLogix ControlNet Bridge Module, Series E Release Notes

1756 10/100Mbps EtherNet/IP Bridge, Twisted Pair Media Release Notes

1756-ENBT ControlLogix EtherNet/IP Product Profile

ControlLogix EtherNet/IP Bridge Module Installation Instructions