Scribd Logo
Upload

Welcome to Scribd!

  • 161 views

    010 - AR200 Product Data Sheet 2012 04 01

    Uploaded by

    Baihaki St
    AR200 steel plate is an abrasion-resistant steel intended for moderate wear applications like cement mixer drums and conveyor chutes. It has a hardness of 200HBW. It is available in cut-to-length or discrete plate sizes from 0.188 to 1.250 inches thick, 72 to 103 inches wide, and 96 to 1,020 inches long. AR200 can be welded, cold formed, and cut but requires preheating and removal of hardened surface areas. It is suitable for applications requiring wear resistance but not structural integrity.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    010 - AR200 Product Data Sheet 2012 04 01

    Uploaded by

    Baihaki St
    161 views2 pages
    AR200 steel plate is an abrasion-resistant steel intended for moderate wear applications like cement mixer drums and conveyor chutes. It has a hardness of 200HBW. It is available in cut-to-length or discrete plate sizes from 0.188 to 1.250 inches thick, 72 to 103 inches wide, and 96 to 1,020 inches long. AR200 can be welded, cold formed, and cut but requires preheating and removal of hardened surface areas. It is suitable for applications requiring wear resistance but not structural integrity.

    Original Description:

    010_AR200 Product Data Sheet 2012 04 0

    Original Title

    010_AR200 Product Data Sheet 2012 04 01

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    AR200 steel plate is an abrasion-resistant steel intended for moderate wear applications like cement mixer drums and conveyor chutes. It has a hardness of 200HBW. It is available in cut-to-length or discrete plate sizes from 0.188 to 1.250 inches thick, 72 to 103 inches wide, and 96 to 1,020 inches long. AR200 can be welded, cold formed, and cut but requires preheating and removal of hardened surface areas. It is suitable for applications requiring wear resistance but not structural integrity.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    161 views2 pages

    010 - AR200 Product Data Sheet 2012 04 01

    Uploaded by

    Baihaki St
    AR200 steel plate is an abrasion-resistant steel intended for moderate wear applications like cement mixer drums and conveyor chutes. It has a hardness of 200HBW. It is available in cut-to-length or discrete plate sizes from 0.188 to 1.250 inches thick, 72 to 103 inches wide, and 96 to 1,020 inches long. AR200 can be welded, cold formed, and cut but requires preheating and removal of hardened surface areas. It is suitable for applications requiring wear resistance but not structural integrity.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ABRASION-RESISTANT PLATE

    Product Data Sheet 2012 04 01


    Page |1

    AR200
    Abrasion-Resistant Steel Plate
    General Product Description
    AR200 steel plate is a carbon-manganese steel plate product with nominal hardness of
    200HBW, intended for moderate wear applications. AR200 is available as cut-to-length or
    discrete as-rolled plate. AR200 is not intended for structural applications.

    Applications
    Typical applications for AR200 steel plate include cement mixer drums and fins, bulk material
    handling chute liners, skirtboard liners, and screw conveyers.

    Dimensions: The following AR200 plate sizes are available.


    Product Type
    Cut-to-Length Plate

    Discrete Plate

    Thickness, in [mm]
    0.188 0.500
    [4.8 12.7]
    0.188 to < 0.250
    [4.8 to < 6.4]
    0.250 1.250
    [6.4 31.8]

    Width, in [mm]
    72 96
    [1,830 - 2,438]
    72 96
    [1,830 - 2,438]
    72 103
    [1,830 - 2,616]

    Length, in [mm]
    96 720
    [2,438 18,288]
    240 1,020
    [6,096 25,908]
    240 1,020
    [6,096 25,908]

    Mechanical Properties
    AR200 has a nominal hardness of 200 HBW and is generally produced to a specified chemical
    composition only. Applications requiring specific mechanical properties should be inquired.

    Chemical Composition (typical ladle analysis, Wt. %)


    C
    0.35

    Mn
    1.20

    P
    0.012

    S
    0.005

    Si
    0.25

    CEV
    0.60

    CET
    0.50

    Testing
    Brinell hardness (HBW) is tested according to ASTM A370, on a milled or ground surface 0.020
    to 0.118 (0.5 - 3.0 mm) below the plate surface.

    Tolerances
    Thickness, width, and length tolerances are in accordance to ASTM A6. ASTM A6 half-standard
    flatness tolerance is available for discrete plate greater than or equal to 0.375 (9.5 mm) thick
    and for cut-to-length plate.

    www.ssab.com

    ABRASION-RESISTANT PLATE

    Product Data Sheet 2012 04 01


    Page |2

    Fabrication and Other Recommendations


    Cutting
    AR200 steel plate can be gas cut satisfactorily. The hardened, heat-affected zones adjacent to
    the cut surfaces should be removed before any subsequent forming or welding operation.

    Weldability
    AR200 is weldable by conventional electric arc welding processes, using low-hydrogen
    consumables and appropriate welding practices. The following recommendations should be
    considered.
    Welding Process

    Thickness

    Shielded Metal Arc (SMAW)


    Gas Metal Arc (GMAW)
    Submerged Arc Weld (SAW)
    Flux Cored Arc Welding (FCAW)

    Up to
    1.25
    Up to
    1.25
    Up to
    1.25
    Up to
    1.25

    Preheat / Interpass
    Temperature
    o
    o
    300 F (150 C)
    o
    o
    400 F (200 C)
    o
    o
    300 F (150 C)
    o
    o
    400 F (200 C)
    o
    o
    300 F (150 C)
    o
    o
    400 F (200 C)
    o
    o
    300 F (150 C)
    o
    o
    400 F (200 C)

    Consumables
    AWS E10018 or
    E9018
    AWS ER90S-X with
    %V < 0.05%
    AWS F9X-EXXX
    AWS E9XT-X

    When matching consumables are not required, lower strength electrodes (ER70, E7XT, E7X or
    E7018) are recommended. Slow-cooling after welding and a post-weld heat treatment at
    1100F (595C) are suggested to minimize cold cracking. The electrodes for shielded metal arc
    welding must be properly stored and dried; the welding flux must be properly dried for
    submerged arc welding.

    Formability
    AR200 may be employed in moderate cold forming applications. Proper edge preparation (i.e.
    removal of hardened heat-affected zones adjacent to the cut surfaces) is essential to minimize
    the potential for cracking. Cold forming should be performed at a minimum temperature of 68F
    (20C). Minimum recommended punch radius, R, and die width opening, W, as a function of
    bending orientation is provided in the following table.

    Thickness
    in [mm]
    0.1875 0.250
    [4.8 6.4]
    >0.250 0.500
    [>6.4 12.7]
    >0.500 1.25
    [>12.7 31.8]

    Bend axis perpendicular


    to rolling direction
    Min. Punch
    Die width W
    Radius, R

    Bend axis parallel


    to rolling direction
    Min. Punch
    Die width W
    Radius, R

    3t

    10t

    4.5t

    12t

    4t

    11t

    6t

    15t

    8t

    20t

    10t

    22t

    Sales Contacts
    For sales information, please call 877-294-3858 (Southern USA & Mexico), 800-340-5566
    (Western and Central USA), 800-383-9031 (North Central USA), and 888-576-8530 (Northeast
    USA & Canada) or consult www.ssab.com.
    www.ssab.com

    You might also like