1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

1999-2000 ACCESSORIES & EQUIPMENT

Power Windows - Trucks

DESCRIPTION & OPERATION

Depending on model, system components vary. System components may consist of a power main relay, body
control ECU, integration relay or instrument ECU. See WIRING DIAGRAMS . All models have power
window switches and power window motors for each door. With ignition switch in ON position, battery voltage
is supplied through power main relay or body control ECU to power window switches. Power window switch
supplies power and ground for power window motors. 4Runner also has a power window switch and lock
switch for tailgate door.
Driver's power window switch offers one-touch operation of driver's window. Driver's power window switch
also includes a lock-out feature to prevent passengers from operating any other power window switches.

ADJUSTMENTS
ADJUSTING METHOD FOR JAM PROTECTION
NOTE:

Use this procedure when power window motor has been replaced or when
power window motor has been run while removed from vehicle.

To adjust limit switch to OFF position, connect motor to harness connector and operate power window motor in
UP direction for 4-5 seconds. This sets limit switch to full UP position (OFF).

TROUBLE SHOOTING
NOTE:

Trouble shooting available for Land Cruiser and RAV4 models only. For
connector views for trouble shooting diagnostic steps, see CONNECTOR
VIEWS .

WINDOW REVERSES WHEN OPERATED IN AUTO UP MODE (DRIVER'S WINDOW ONLY)

If window reverses when window is being raised in AUTO UP mode, check door glass run, window regulator,
window motor or window guide for sign of damage or misalignment. Resistance in window glass movement
causes window to reverse direction. Check power window motor limit switch for proper adjustment. See
ADJUSTING METHOD FOR JAM PROTECTION under ADJUSTMENTS. If all mechanical checks are
okay, replace driver's power window master switch with a known-good unit and retest.
AUTO REVERSE INOPERATIVE WITH OBSTRUCTION IN WINDOW
NOTE:

This test diagnoses inoperative AUTO REVERSE operation (jam function) when
foreign object restricts window up operation. AUTO REVERSE mode will not
operate when window is within .157" (4 mm) of fully open position.

Microsoft
Sunday, November 22, 2009 10:59:39
10:59:35 AM

Page 1

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

1. Ensure all power window modes function normally (i.e., UP, DOWN, AUTO UP, AUTO DOWN and
key OFF). If all modes function normally, go to next step. If all modes do not function normally, perform
appropriate symptom test.
2. AUTO REVERSE should operate when there is resistance to power window motor while raising window.
If window opening is greater than 7.874" (200 mm) when window glass travel is obstructed, window will
automatically lower 1.969" (50 mm) and stop. If window opening is 7.874" (200 mm) or less when
window glass travel is obstructed, window will automatically lower until opening is 7.874" (200 mm) and
stop. If operation is as specified, system is okay at this time. If operation is not as specified, go to next
step.
3. Check power window motor limit switches for proper adjustment. See ADJUSTING METHOD FOR
JAM PROTECTION under ADJUSTMENTS. Ensure power window motor is installed correctly. If
motor is installed correctly and AUTO REVERSE still does not operate as specified, replace power
window master switch or power window control switch.
ONE-TOUCH POWER WINDOW IS INOPERATIVE
NOTE:

When a fault for one-touch mode in driver's power window master switch
occurs, AUTO light on power window master switch will output a flash code.
After 30 seconds, AUTO light will stop flashing and will stay on. If ignition
switch is turned to OFF position during flash mode, flashing will stop.

1. Turn ignition switch to ON position and toggle power window master switch to UP or DOWN position
for driver's side window only. Ensure power window master switch AUTO light begins to flash fault
code. See Fig. 1 . For Fault Code 1, go to next step. For Fault Code 2 or 3, go to step 3 . If AUTO light
does not stay illuminated after 30 seconds, or flashes stop after ignition switch is turned to OFF position,
replace power window master switch.
2. Fault Code 1 occurs when there is an error in power window motor limit switch. Remove power window
master switch from door panel, with connector attached. Measure voltage by backprobing between power
window master switch connector terminals No. 1 and 5. Voltage should change from zero volts when
window is fully closed, to 10-14 volts while window is opening. If voltage is not as specified, go to next
step. If voltage is as specified, replace power window master switch. If AUTO UP and AUTO DOWN
does not work after power window master switch is replaced, replace power window motor.
3. Disconnect power window master switch and driver's power window motor from harness connectors.
Check continuity between appropriate power window master switch terminals and driver's power window
motor terminals. See ONE-TOUCH POWER WINDOW TESTS table. If continuity is present at all
measurements, go to next step. If continuity is not present at any measurement, repair open circuit in
affected wire.
ONE-TOUCH POWER WINDOW TESTS
Model
Check Between Master Switch Terminal
No. & (Driver's Window Motor Terminal
No.)
Land Cruiser
(1) 1 & (4)
Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 2

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

(2) 7 & (3)

(2) 5 & (5)

RAV4 (2-Door)
(1) 4 & (4)
(1) 1 & (3)
(1) 10 & (5)

RAV4 (4-Door)
(1) 1 & (1)
(2) 7 & (3)
(2) 5 & (5)
(1) See Fig. 5 and Fig. 7 .
(2) See Fig. 5 and Fig. 6 .

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 3

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 4

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 1: Identifying AUTO Light Flash Codes

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. With master switch and driver's window motor disconnected, check for continuity between master switch
harness 14-pin connector terminals No. 1, 5 and 7 on Land Cruiser and RAV4 4-door or terminals No. 1,
4 and 10 on RAV4 2-door. For correct terminal to connector location, see appropriate wiring diagram
under WIRING DIAGRAMS . If continuity is not present, go to next step. If continuity is present, repair
short between affected wires.
5. With master switch and driver's window motor disconnected, check continuity between driver's power
window motor harness connector terminals No. 3, 4, 5 and ground. If continuity is not present, go to next
step. If continuity is present, repair short to ground in affected wire.
6. Connect harness connectors to master switch and driver's power window motor. Ensure AUTO UP and
AUTO DOWN function operates correctly. If AUTO UP and AUTO DOWN function still does not
operate correctly, replace power window motor.

COMPONENT TESTS
POWER WINDOW SWITCH CONTINUITY TEST (DRIVER'S SWITCH)
Using an ohmmeter, check continuity between specified terminals with driver's power window switch in
specified position. See appropriate DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST table.
See Fig. 6 -Fig. 9 . Continuity should be present, except at those terminals specified by a footnote. If continuity
is not as specified, replace power window switch. If continuity is as specified, switch is okay.
DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (LAND CRUISER)
(1) Terminals No.

Application & Switch Position

Driver's Switch
Locked & Unlocked
UP
OFF
DOWN
Passenger's Switch
Locked
UP
OFF
DOWN
Unlocked
UP
OFF
DOWN
Left Rear Switch
Locked
UP

1 & 3; 2, 4 & 5
1, 2, 4 & 5
1, 4 & 5; 2 & 3

7 & 10
7&8
8 & 10
4, 5, 8; 7 & 10
4, 5, 7 & 8
4, 5, 7; 8 & 10

9 & 10

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 5

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

OFF
DOWN
Unlocked
UP
OFF
DOWN
Right Rear Switch
Locked
UP
OFF
DOWN
Unlocked
UP
OFF
DOWN
(1) See Fig. 7 .

9 & 11
10 & 11
4, 5 & 11; 9 & 10
4, 5, 9 & 11
4, 5 & 9; 7, 10 & 11

10 & 13
13 & 14
10 & 14
4, 5 & 14; 10 & 13
4, 5, 13 & 14
4, 5 & 13; 10 & 14

DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (RAV4)

(1) Terminals No.

Application & Switch Position

2-Door
Driver's Switch
Locked & Unlocked
UP
OFF
DOWN
Passenger's Switch
Locked
UP
OFF
DOWN
Unlocked
UP
OFF
DOWN
4-Door
Driver's Switch
Locked & Unlocked
UP
OFF
DOWN

3 & 5; 4 & 6
3, 4 & 5
3 & 4; 5 & 6

12 & 13
12 & 14
13 & 14
3 & 14; 12 & 13
3, 12 & 14
3 & 12; 13 & 14

1 & 3; 2, 4 & 5
1, 2, 4 & 5
2 & 3; 1, 4 & 5

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 6

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Passenger's Switch
Locked
UP
7 & 10
OFF
7&8
DOWN
8 & 10
Unlocked
UP
4, 5 & 8; 7 & 10
OFF
4, 5, 7 & 8
DOWN
4, 5 & 7; 8 & 10
Left Rear Switch
Locked
UP
9 & 10
OFF
9 & 11
DOWN
10 & 11
Unlocked
UP
4, 5 & 11; 9 & 10
OFF
4, 5, 9 & 10
DOWN
4, 5 & 9; 10 & 11
Right Rear Switch
Locked
UP
10 & 13
OFF
13 & 14
DOWN
10 & 14
Unlocked
UP
4, 5 & 14; 10 & 13
OFF
4, 5, 13 & 14
DOWN
4, 5 & 13; 10 & 14
(1) For RAV4 (2-door) master switch terminal locations, see Fig. 6 . For RAV4 (4-door) master switch
terminal locations, see Fig. 7 .
DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (SIENNA & TUNDRA)
(1) Terminals No.

Application & Switch Position

Driver's Switch
Locked & Unlocked
UP
OFF
DOWN
Passenger's Switch
Locked
UP

1 & 4; 3 & 9
1, 3 & 4
1 & 3; 4 & 9

8&9

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 7

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

OFF
DOWN
Unlocked
UP
OFF
DOWN
(1) See Fig. 9 .

8 & 10
9 & 10
1 & 10; 8 & 9
1, 8 & 10
1 & 8; 9 & 10

DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (TACOMA)

(1) Terminals No.

Application & Switch Position

Driver's Switch
Locked & Unlocked
UP
OFF
DOWN
Passenger's Switch
Locked
UP
OFF
DOWN
Unlocked
UP
OFF
DOWN
(1) See Fig. 9 .

3 & 9; 4 & 6
3, 4 & 6
3 & 6; 4 & 9

9 & 10
7 & 10
7&9
6 & 7; 9 & 10
6, 7 & 10
6 & 10; 7 & 9

DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (4RUNNER)

(1) Terminals No.

Application & Switch Position

Driver's Switch
Locked & Unlocked
UP
DOWN
Left Rear Switch
Locked
UP

2&4
1&4

DOWN

(2) 11 & 4
(2) 9 & 4

Unlocked
UP
DOWN

11 & 4
9&4

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 8

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Right Rear Switch

Locked
UP

(2) 14 & 4
(2) 13 & 4

DOWN
Unlocked
UP
DOWN
(1) See Fig. 7 .

14 & 4
13 & 4

(2) Continuity does not exist at these terminals.

POWER WINDOW SWITCH CONTINUITY TEST (PASSENGER'S & REAR SWITCHES)

Using an ohmmeter, check continuity between specified terminals with power window switch in specified
position. See POWER WINDOW SWITCH CONTINUITY TEST (PASSENGER'S & REAR) table. See
Fig. 10 Fig. 11 or Fig. 12 . If continuity does not exist at specified terminals, replace appropriate power window
switch.
POWER WINDOW SWITCH CONTINUITY TEST (PASSENGER'S & REAR)
(1) Terminals No.

Application & Switch Position

Land Cruiser
Passenger's & Rear Switch
UP
OFF
DOWN
Rear Quarter Panel Window Switch
CLOSE
OFF
OPEN
Illumination Circuit
RAV4
Front Switch
UP
OFF
DOWN
Rear Switch
UP
OFF
DOWN
Sienna
Front Switch

1 & 2; 3 & 4
1 & 2; 3 & 5
1 & 4; 3 & 5
3 & 6; 4 & 5
None
3 & 4; 5 & 6
1&2

1 & 2; 3 & 4
1 & 2; 3 & 5
1 & 4; 3 & 5
1 & 2; 3 & 4
1 & 2; 4 & 5
2 & 3; 4 & 5

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 9

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

UP
OFF
DOWN
Rear Quarter Panel Window Switch
CLOSE
OFF
OPEN
Illumination Circuit
Tacoma & Tundra
UP
OFF
DOWN
4Runner
UP
DOWN
(1) See Fig. 10 , Fig. 11 orFig. 12 .

1 & 2; 3 & 4
1 & 2; 3 & 5
1 & 4; 3 & 5
3 & 7; 8 & 9
6 & 7; 8 & 9
3 & 8; 6 & 7
1&5
1 & 2; 3 & 4
1 & 2; 3 & 5
1 & 4; 3 & 5
6 & 12
1 & 12

POWER WINDOW MASTER SWITCH VOLTAGE TEST

Land Cruiser & RAV4

1. Remove master switch and disconnect 14-pin connector. Connect jumper wire between 12-volt battery
positive terminal and master switch terminals No. 3 and 10. Connect another jumper between battery
negative terminal and master switch terminals No. 4 and 5.
2. Measure voltage by backprobing between specified terminals with driver's power window switch in
specified position. See POWER WINDOW MASTER SWITCH VOLTAGE TEST (LAND
CRUISER & RAV4) table. Voltage should be 10-14 volts. If voltage is not as specified, replace power
window switch. If voltage is as specified, switch is okay.
POWER WINDOW MASTER SWITCH VOLTAGE TEST (LAND CRUISER & RAV4)
(1) Terminals No.
Application & Switch Position
Driver's Switch (Lock & Unlock)
UP
DOWN
Passenger's Switch (Locked & Unlocked)
UP
DOWN
Left Rear Switch (Locked & Unlocked)
UP
DOWN
Right Rear Switch (Locked & Unlocked)
UP

1&2
1&2
7&8
7&8
9 & 11
9 & 11
13 & 14

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 10

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

DOWN
(1) For terminal location, see Fig. 7 .

13 & 14

4Runner

1. Remove master switch and disconnect 14-pin connector. Connect jumper wire between 12-volt battery
positive terminal and master switch terminals No. 3 and 10. Connect another jumper between battery
negative terminal and master switch terminal No. 4.
2. Measure voltage by backprobing between specified terminals with driver's power window switch in
specified position. See POWER WINDOW MASTER SWITCH VOLTAGE TEST (4RUNNER)
table. Voltage should be 10-14 volts. If voltage is not as specified, replace power window switch. If
voltage is as specified, switch is okay.
POWER WINDOW MASTER SWITCH VOLTAGE TEST (4RUNNER)
Application & Switch Position
Driver's Switch (Locked & Unlocked)
UP
DOWN
Passenger's Switch (Locked & Unlocked)
UP
DOWN
Left Rear Switch (Locked & Unlocked)
UP
DOWN
Right Rear Switch (Locked & Unlocked)
UP
DOWN
(1) For terminal location, see Fig. 7 .

(1) Terminals No.

1&2
1&2
7&8
7&8
9 & 11
9 & 11
13 & 14
13 & 14

POWER WINDOW SWITCH CONTINUITY TEST (BACK DOOR/TAILGATE)

4Runner

Using an ohmmeter, check continuity between specified terminals with back door/tailgate power window switch
in specified position. See POWER WINDOW SWITCH CONTINUITY TEST (4RUNNER - BACK
DOOR/TAILGATE) table. See Fig. 13 . If continuity does not exist at specified terminals, replace appropriate
power window switch.
POWER WINDOW SWITCH CONTINUITY TEST (4RUNNER - BACK DOOR/TAILGATE)
(1) Terminals No.

Application & Position

UP
OFF

2&6
None

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 11

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

DOWN
Switch Illumination
UP, OFF & DOWN
(1) See Fig. 13 .

1&6
5&8

POWER MAIN RELAY

NOTE:

Land Cruiser uses an instrument ECU and a power main relay. Sienna, Tacoma,
Tundra and RAV4 use an integration relay and a power main relay. 4Runner
uses a body ECU and power main relay.

Land Cruiser, RAV4, Sienna, Tacoma, Tundra & 4Runner

1. Remove power main relay. On RAV4, Sienna, Tundra and 4Runner, relay is located in junction block No.
1 at left side of instrument panel. On Land Cruiser and Tacoma, relay is located behind left kick panel.
On all models, using an ohmmeter, check continuity between power main relay terminals No. 1 and 2.
See Fig. 2 or Fig. 3 . If continuity is present, go to next step. If continuity is not present, replace relay.
2. Connect jumper wire from 12-volt battery positive terminal to relay terminal No. 1. Connect another
jumper from battery negative terminal and relay terminal No. 2. Continuity should then be present at relay
terminals No. 3 and 5. If continuity is not present, replace power main relay.

Fig. 2: Power Main Relay Terminals (Land Cruiser & RAV4)

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 12

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 3: Power Main Relay Terminals (Sienna, Tacoma, Tundra & 4Runner)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
POWER WINDOW MOTOR CIRCUIT BREAKER TEST (DRIVER'S)
Land Cruiser, RAV4 & 4Runner

1. Slightly lower driver's side window glass. Disconnect 14-pin connector from power window master
switch. Connect jumper wire from 12-volt battery positive terminal to master switch harness connector
terminal No. 1. See Fig. 7 . Connect another jumper wire from battery negative terminal to master switch
harness connector terminal No. 2. Window should raise to fully closed position. If window operates
correctly, go to next step. If window does not operate correctly, see POWER WINDOW MOTOR
TEST .
2. Continue to apply voltage until there is an audible click from power window motor circuit breaker (within
4-40 seconds). Reverse polarity and ensure window begins to descend within about 60 seconds. If
operation is not as specified, replace power window motor. If operation is as specified, power window
motor circuit breaker is okay.
Sienna, Tacoma & Tundra

1. Slightly lower driver's side window glass. Disconnect 10-pin connector from power window master
switch. Connect jumper wire from 12-volt battery positive terminal to master switch harness connector
terminal No. 3. See Fig. 9 . Connect another jumper wire from battery negative terminal to master switch
harness connector terminal No. 4. Window should raise to fully closed position. If window operates
correctly, go to next step. If window does not operate correctly, see POWER WINDOW MOTOR
TEST .
2. Continue to apply voltage until there is an audible click from power window motor circuit breaker (within
4-40 seconds). Reverse polarity and ensure window begins to descend within about 60 seconds. If
operation is not as specified, replace rear power window motor. If operation is as specified, rear power
Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 13

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

window motor circuit breaker is okay.

POWER WINDOW MOTOR CIRCUIT BREAKER TEST (PASSENGER'S & REAR)
Sienna, Tundra, Land Cruiser, RAV4 & 4Runner (Rear Only)

1. Slightly lower window glass. Disconnect 5-pin connector from power window switch. Connect jumper
wire from 12-volt battery positive terminal to power window switch harness connector terminal No. 3.
See Fig. 7 . Connect another jumper wire from battery negative terminal to power window switch harness
connector terminal No. 1. Window should raise to fully closed position. If window operates correctly, go
to next step. If window does not operate correctly, see POWER WINDOW MOTOR TEST .
2. Continue to apply voltage until there is an audible click from power window motor circuit breaker (within
4-40 seconds). Reverse polarity and ensure window begins to descend within about 60 seconds. If
operation is not as specified, replace power window motor. If operation is as specified, power window
motor circuit breaker is okay.
4Runner (Passenger Only)

1. Slightly lower window glass. Disconnect 12-pin connector from power window switch. Connect jumper
wire from 12-volt battery positive terminal to power window switch harness connector terminal No. 6.
See Fig. 8 . Connect another jumper wire from battery negative terminal to power window switch harness
connector terminal No. 1. Window should raise to fully closed position. If window operates correctly, go
to next step. If window does not operate correctly, see POWER WINDOW MOTOR TEST .
2. Continue to apply voltage until there is an audible click from power window motor circuit breaker (within
4-40 seconds). Reverse polarity and ensure window begins to descend within about 60 seconds. If
operation is not as specified, replace power window motor. If operation is as specified, power window
motor circuit breaker is okay.
POWER WINDOW MOTOR TEST
Driver's Window Motor (Land Cruiser & RAV4)

Using a 12-volt battery, connect positive battery lead to power window motor terminal No. 1. See Fig. 5 .
Connect negative battery lead to power window motor connector terminal No. 4. Motor should operate. Reverse
battery leads. Motor should operate in opposite direction. If motor does not test as specified, replace motor.
Rear Quarter Window Motors (Land Cruiser)

Connect jumper wire between 12-volt battery positive terminal to power window motor terminal No. 1 (on left
side window), No. 2 (on right side window). See Fig. 4 . Connect negative battery lead to other power window
motor connector terminal. Window link should move to OPEN position. When battery jumper is removed,
window link should move to CLOSED position. If motor does not operate as specified, replace motor.
All Other Window Motors

Using a 12-volt battery, connect positive battery lead to either power window motor terminal. Connect negative
battery lead to other power window motor connector terminal. Motor should operate. Reverse battery leads.
Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 14

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Motor should operate in opposite direction. If motor does not test as specified, replace motor.
POWER WINDOW LOCK SWITCH
Tailgate Door (4Runner)

Switch Continuity Test

Disconnect power window lock switch Black 10-pin connector, located on left side of instrument panel.
Using an ohmmeter, check continuity between terminals No. 7 (White/Black wire) and No. 10
(Blue/White wire) with lock switch in UNLOCK position. See Fig. 13 . Continuity should be present.
With lock switch in LOCK position, continuity should not be present. If continuity is not as specified,
replace switch.
Switch Illumination Circuit Test
Check continuity between power window lock switch terminals No. 2 (Green wire) and No. 3
(Green/White wire). Continuity should be present with power window lock switch in LOCK or UNLOCK
position. If continuity is not as specified, replace power window lock switch.
POWER WINDOW LIMIT SWITCH
Tailgate Door (4Runner)

Disconnect power window limit switch 2-pin connector, located on left side of tailgate door, behind trim panel.
Using an ohmmeter, check continuity between terminals No. 1 (Red/Blue wire) and No. 2 (White/Black wire)
with switch in ON position. Continuity should exist. With switch in OFF position, continuity should not exist. If
continuity is not as specified, replace switch.

CONNECTOR VIEWS
Use the following connector views for diagnostic pin point tests in TROUBLE SHOOTING , COMPONENT
TESTS and CIRCUIT TESTS . See Fig. 4 -Fig. 13 .

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 15

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 4: Identifying Rear Quarter Power Window Motor Terminals (Land Cruiser)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 16

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 5: Identifying Driver's Power Window Motor Terminals (Land Cruiser & RAV4)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 17

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 6: Identifying Driver's Power Window Master Switch 7-Pin Connector Terminals (Land Cruiser,
RAV4 (4-Door) & 4Runner)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 7: Identifying Driver's Power Window Master Switch 14-Pin Connector Terminals (Land Cruiser,
RAV4 & 4Runner)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 18

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 8: Identifying Passenger's Power Window Switch Connector Terminals (4Runner)

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 9: Identifying Driver's Power Window Master Switch Connector Terminals (Sienna, Tacoma &
Tundra)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 19

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 10: Identifying Rear Quarter Power Window Switch Connector Terminals (Land Cruiser)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 11: Identifying Rear Quarter Power Window Switch Connector Terminals (Sienna)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 20

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 12: Identifying Passenger & Rear Power Window Switch Connector Terminals (Land Cruiser,
RAV4, Sienna, Tacoma, Tundra & 4Runner)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 13: Identifying Back Door/Tailgate Power Window Switch Connector Terminals (4Runner)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

CIRCUIT TESTS
INTEGRATION RELAY CIRCUIT TEST
Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 21

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

NOTE:

Diagnostic procedures for integration relay circuit is not available.

POWER WINDOW MASTER SWITCH ILLUMINATION TEST

Land Cruiser & RAV4 (4-Door)

Disconnect power window master switch 14-pin connector. Connect jumper wire from 12-volt battery positive
terminal to master switch connector terminals No. 3 and 10. Connect another jumper wire from negative battery
terminal to master switch connector terminal No. 4. Ensure all switch lights illuminate. If operation is not as
specified, replace power window master switch.
RAV4 (2-Door)

Disconnect power window master switch 14-pin connector. Connect jumper wire from 12-volt battery positive
terminal to master switch connector terminals No. 6 and 13. Connect another jumper wire from negative battery
terminal to master switch connector terminal No. 3. Ensure all switch lights illuminate. If operation is not as
specified, replace power window master switch.
Sienna

Disconnect power window master switch 14-pin connector. Place window lock switch in UNLOCK position.
Connect jumper wire from 12-volt battery positive terminal to master switch connector terminal No. 9. Connect
another jumper wire from negative battery terminal to master switch connector terminal No. 1. Ensure all switch
lights illuminate. Place window lock switch in LOCK position and ensure passenger power window switches do
not illuminate. If operation is not as specified, replace power window master switch.
POWER WINDOW SWITCH POWER SUPPLY TEST
NOTE:

Testing for Land Cruiser, RAV4 and Tacoma is not available.

Sienna, Tundra & 4Runner

Disconnect power window switch connector. Measure battery voltage between appropriate power window
switch harness connector terminal and ground. See POWER WINDOW SWITCH POWER SUPPLY TEST
table. With ignition switch in ON position, voltage should be 10-14 volts. If voltage is not as specified, repair
open in affected circuit.
POWER WINDOW SWITCH POWER SUPPLY TEST
Application & Switch
Sienna

Condition

Terminal No.

Power Window Master Switch (1)

(2) Ignition Switch In ACC Or LOCK Position

Ignition Switch In ON Position

Rear Quarter Power Window Switch (3)

(2) Ignition Switch In ACC Or LOCK Position

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 22

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Ignition Switch In ON Position

Tundra
Driver Power Window Master Switch (1)
(2) Ignition Switch In ACC Or LOCK Position

Ignition Switch In ON Position

Passenger Power Window Switch (4)

(2) Ignition Switch In ACC Or LOCK Position

Ignition Switch In ON Position

4Runner
Driver Power Window Master Switch (5)
(2) Ignition Switch In ACC Or LOCK Position

10

Ignition Switch In ON Position

Constant

10
3

Passenger Power Window Switch (6)

Constant
(1) For switch terminal location, see Fig. 9 .

(2) Voltage will be present for up to 45 seconds after ignition switch is turned to OFF position, or until

driver or passenger door is opened.

(3) For switch terminal location, see Fig. 11 .
(4) For switch terminal location, see Fig. 12 .
(5) For switch terminal location, see Fig. 7 .
(6) For switch terminal location, see Fig. 8 .

POWER WINDOW SWITCH GROUND TEST

NOTE:

Testing for Land Cruiser, Tacoma and RAV4 is not available.

Disconnect power window switch connector. Check for continuity between appropriate power window switch
harness connector terminal and ground. See POWER WINDOW SWITCH GROUND TEST table.
Continuity should be present at all times. If continuity is not present, repair open in ground circuit.
POWER WINDOW SWITCH GROUND TEST
Application & Switch
Sienna

Terminals No.

Driver Power Window Master Switch (1)

Rear Quarter Power Window Switch (2)

Tundra

6&9

Driver Power Window Master Switch (1)

Microsoft
Sunday, November 22, 2009 10:59:35 AM

Page 23

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

4Runner
Driver Power Window Master Switch (3)

Passenger Power Window Switch (4)

(1) For switch terminal location, see Fig. 9 .

12

(2) For switch terminal location, see Fig. 11 .

(3) For switch terminal location, see Fig. 7 .
(4) For switch terminal location, see Fig. 8 .

POWER WINDOW SYSTEM CURRENT TEST

NOTE:

System circuit breaker opens 4-40 seconds after window operation stops.
Ensure circuit test is performed before circuit breaker operates.

Land Cruiser, 4Runner & RAV4 (4-Door)

1. Disconnect driver's power window switch connector. Connect positive lead of ammeter to driver's power
window switch harness connector terminal No. 1. See Fig. 7 .
2. Connect ammeter negative lead to negative terminal of 12-volt battery. Connect jumper wire from
positive battery terminal to driver's power window switch harness connector terminal No. 2.
3. As driver's window is lowered, current should be about 7 amps. When window reaches fully opened
position, current should increase to about 14.5 amps or more. If current is as specified, replace driver's
power window master switch. If current is not as specified, check and repair appropriate circuit.
RAV4 (2-Door)

1. Disconnect driver's power window switch connector. Connect positive lead of ammeter to driver's power
window switch harness connector terminal No. 4. See Fig. 7 .
2. Connect ammeter negative lead to negative terminal of 12-volt battery. Connect jumper wire from
positive battery terminal to driver's power window switch harness connector terminal No. 5.
3. As driver's window is lowered, current should be about 7 amps. When window reaches fully opened
position, current should increase to about 14.5 amps or more. If current is as specified, replace driver's
power window switch. If current is not as specified, check and repair appropriate circuit.
Sienna & Tundra

1. Disconnect driver's power window switch connector. Connect positive lead of ammeter to driver's power
window switch harness connector terminal No. 3. See Fig. 9 .
2. Connect ammeter negative lead to negative terminal of 12-volt battery. Connect jumper wire from
positive battery terminal to driver's power window switch harness connector terminal No. 4.
3. As driver's window is lowered, current should be about 7 amps. When window reaches fully opened
position, current should increase to about 14.5 amps or more. If current is as specified, replace driver's
power window switch. If current is not as specified, check and repair appropriate circuit.
Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 24

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Tacoma

1. Disconnect driver's power window switch connector. Connect positive lead of ammeter to driver's power
window switch harness connector terminal No. 4. See Fig. 9 .
2. Connect ammeter negative lead to negative terminal of 12-volt battery. Turn ignition switch to ON
position. Connect a jumper wire from positive battery terminal to driver's power window switch harness
connector terminal No. 9.
3. As driver's window is lowered, current should be about 7 amps. When window reaches fully opened
position, current should increase to about 14.5 amps or more. If current is as specified, replace driver's
power window switch. If current is not as specified, check and repair appropriate circuit.

REMOVAL & INSTALLATION

POWER WINDOW MOTOR
Removal & Installation

Remove door trim panel and waterproof shield. Remove glass retaining bolts and glass. Remove window
regulator bolts, and remove window regulator/power window motor assembly. Remove power window motor
retaining screws, and remove motor from window regulator. To install, reverse removal procedure. Tighten
window regulator motor retaining bolts or nuts to 44 INCH lbs. (5 N.m). Apply multipurpose grease to window
regulator rollers.
POWER WINDOW SWITCH
Removal & Installation

Disconnect negative battery cable. Using a small flat blade screwdriver, pry and lift power window switch from
door panel. Disconnect power window switch connector(s) and remove switch. To install, reverse removal
procedure.

WIRING DIAGRAMS

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 25

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 26

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 14: Power Window System Wiring Diagram (2000 Tundra)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 27

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 28

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 15: Power Window System Wiring Diagram (Land Cruiser)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 29

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 30

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 16: Power Window System Wiring Diagram (RAV4 - 2-Door)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 31

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 32

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 17: Power Window System Wiring Diagram (RAV4 - 4-Door)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 33

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 34

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 18: Power Window System Wiring Diagram (Sienna)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 35

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 36

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 19: Power Window System Wiring Diagram (Tacoma)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 37

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 38

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 20: Power Window System Wiring Diagram (4Runner)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 39

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 40

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 21: Tailgate Power Window System Wiring Diagram (4Runner)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 41

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 42

2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4

1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks

Fig. 22: Rear Quarter Power Window System Wiring Diagram (Land Cruiser)

Microsoft
Sunday, November 22, 2009 10:59:36 AM

Page 43

2005 Mitchell Repair Information Company, LLC.