How to compute tonnage requirements:
1.
General - When pressure per square inch is known:
psi x area of work/2000 = 2 tons of ram force required
Example: Where it is known that 100 psi is needed to do a job on a 5" x 8" wide piece.
100 x 5" x 8"/2000 = 2 tons
2.
Press Fit - To determine the force required to press fit two round pieces together such as a
shaft pressed into a bushing, use the following formula:
F = D x x L x I x P/2
Where:
F = force required in tons
D = diameter of the part to be pressed in inches
L = length of part to be pressed in inches (Note: the length of the interference fit only.)
I = interference in inches (usually .002" to .006")
P = pressure factor (See table below).
Diameter
(inches)
Pressure
Factor
Diameter
(inches)
Pressure
Factor
Diameter
(inches)
Pressure
Factor
Diameter
(inches)
Pressure
Factor
500
156
91
64
395
143
86
61
325
132
82
59
276
123
78
57
240
115
75
55
212
108
72
189
101
69
171
96
66
Example: A steel shaft 2" in diameter pressed into a hole 3" long. The interference fit between
the two diameters is .006".
2" x 3.14 x 3" x .006" x (240/2) = 13.56 tons
3.
Punching - A quick guide to determine tonnage requirements for punching steel is:
Diameter x thickness x 80 = tons (where 80 is constant for steel. Use 65 for brass.)
Example: A 3" hole in .250" stock: 3" x .250" x 80 = 60 tons
For noncircular holes, instead of the diameter, use 1/3 of the total length of cut.
Example: A rectangular hole 4" x 6" in .250" stock: (4" + 6" + 4" + 6"/3) x .250" x 80 = 133.3
tons
4.
Deep Drawing - Deep-drawing calculations can be complex. The press, dies, material, radius,
and part shape all have bearing. For drawing round shells, the following formula is a simple
guide:
C x T x Ts = tons
Where:
C = circumference of the finished part; T = material thickness in inches; and
Ts = tensile strength of the material.
Example: To draw a 5" diameter cup of .040" stock with a tensile strength of 46,000 psi would
require the following tonnage:
(5 x 3.1416) x .040 x (46000/2000) = 14.44 tons
A 20-ton press would be recommended
5.
Straightening - The pressure required to straighten a piece of metal depends on its shape.
Below is an approximate formula with a further definition for different shapes.
Where F is the ram force in tons; 6 is a constant; U is ultimate strength of the material in psi; Z
is the section modulus (see below); and L is the distance between the straightening blocks in
inches.
Example: A 2" diameter shaft, 18" between the blocks, 100,000 psi ultimate strength.
How to determine strokes per minute for a hydraulic press
The number of strokes per minute for a hydraulic press is determined by calculating a separate
time for each phase of the ram stroke. The rapid advance time is calculated, then the pressing
time, (the work stroke); then, if there is no dwell time, the rapid return.
The basic formula for determining the length of time in seconds for each phase of the stroke:
Example: a hydraulic press with a 600 IPM rapid advance, 60 IPM pressing speed, and 600 IPM
rapid return. The work requires a 3" advance, 1" work stroke, and 4" rapid return.
60 2.199 = 27 cycles per minute.
* Electrical actuation and valve shift time varies depending on the type of hydraulic circuit. One half
second is a reasonable average figure.
1. These formulae are intended as guidelines only. Please consult a qualified manufacturing engineer for
recommendations concerning your specific requirements.
2. Based on steel shaft and cast iron bushing (with OD/ID > 2).
