CFD Ec 2 2004 PDF

Concrete Frame Design Manual
Eurocode 2-2004 with 8-2004
Concrete Frame
Design Manual
Eurocode 2-2004
with
Eurocode 8-2004
For ETABS 2015
ISO ETA082914M23 Rev. 0
Proudly developed in the United States of America
December 2014
Copyright
Copyright Computers & Structures, Inc., 1978-2014
All rights reserved.
The CSI Logo, SAP2000, ETABS, and SAFE are registered trademarks of
Computers & Structures, Inc. Watch & LearnTM is a trademark of Computers & Structures,
Inc.
The computer programs SAP2000 and ETABS and all associated documentation are
proprietary and copyrighted products. Worldwide rights of ownership rest with Computers
& Structures, Inc. Unlicensed use of these programs or reproduction of documentation in
any form, without prior written authorization from Computers & Structures, Inc., is explicitly prohibited.
No part of this publication may be reproduced or distributed in any form or by any means,
or stored in a database or retrieval system, without the prior explicit written permission of
the publisher.
Further information and copies of this documentation may be obtained from:
Computers & Structures, Inc.
http://www.csiamerica.com/
[email protected] (for general information)
[email protected] (for technical support)
DISCLAIMER
CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE

DEVELOPMENT AND TESTING OF THIS SOFTWARE. HOWEVER, THE USER
ACCEPTS AND UNDERSTANDS THAT NO WARRANTY IS EXPRESSED OR
IMPLIED BY THE DEVELOPERS OR THE DISTRIBUTORS ON THE ACCURACY
OR THE RELIABILITY OF THIS PRODUCT.
THIS PRODUCT IS A PRACTICAL AND POWERFUL TOOL FOR STRUCTURAL
DESIGN. HOWEVER, THE USER MUST EXPLICITLY UNDERSTAND THE BASIC
ASSUMPTIONS OF THE SOFTWARE MODELING, ANALYSIS, AND DESIGN
ALGORITHMS AND COMPENSATE FOR THE ASPECTS THAT ARE NOT
ADDRESSED.
THE INFORMATION PRODUCED BY THE SOFTWARE MUST BE CHECKED BY A
QUALIFIED AND EXPERIENCED ENGINEER. THE ENGINEER MUST
INDEPENDENTLY VERIFY THE RESULTS AND TAKE PROFESSIONAL
RESPONSIBILITY FOR THE INFORMATION THAT IS USED.
Contents
Chapter 1
Chapter 2
Introduction
1.1 Organization
1-2
1.2 Recommended Reading/Practice
1-2
Design Prerequisites
2.1 Design Load Combinations
2-1
2.2 Design and Check Stations
2-3
2.3 Identifying Beams and Columns
2-3
2.4 Design of Beams
2-3
2.5 Design of Columns
2-4
2.6 P-Delta Effects
2-5
2.7 Element Unsupported Lengths
2-5
Concrete Frame Design Eurocode 2-2004

2.8 Choice of Input Units
Chapter 3
Design Process
3.1 Notation
3-1
3.2 Assumptions / Limitations
3-4
3.3 Design Load Combinations
3-5
3.4 Column Design
3-8
3.4.1
3.4.2
3.4.3
3.4.4
Generation of Biaxial Interaction Surface

Calculate Column Capacity Ratio
Design Longitudinal Reinforcement
Design Column Shear Reinforcement
3.5 Beam Design

3.5.1 Design Beam Flexural Reinforcement
3.5.2 Design Beam Shear Reinforcement
3.5.3 Design Beam Torsion Reinforcement
Chapter 4
2-6
3-9
3-12
3-18
3-18
3-22
3-22
3-30
3-33
Seismic Provisions
4.1 Notations
4-2
4.2 Design Preferences
4-3
4.3 Overwrites
4-3
4.4 Supported Framing Types
4-4
4.5 Member Design
4-4
4.5.1 Ductility Class High Moment-Resisting Frames 4-4

4.5.2 Ductility Class Medium Moment-Resisting
Frames
4-19
4.5.3 Ductility Class Low Moment-Resisting Frames 4-23
4.5.4 Special Consideration for Seismic Design
4-23
ii
Contents
Appendix A
Second Order P-Delta Effects
Appendix B
Member Unsupported Lengths and Computation of

-Factors
Appendix C
Concrete Frame Design Preferences
Appendix D
Concrete Frame Overwrites
Appendix E
Error Messages and Warnings
Appendix F
Nationally Determined Parameters (NDPs)
References
iii
Chapter 1
Introduction
The design of concrete frames is seamlessly integrated within the program. Initiation of the design process, along with control of various design parameters, is
accomplished using the Design menu.
Automated design at the object level is available for any one of a number of
user-selected design codes, as long as the structure has first been modeled and
analyzed by the program. Model and analysis data, such as material properties
and member forces, are recovered directly from the model database, and no
additional user input is required if the design defaults are acceptable.
The design is based on a set of user-specified loading combinations. However,
the program provides default load combinations for each design code supported.
If the default load combinations are acceptable, no definition of additional load
combinations is required.
In the design of columns, the program calculates the required longitudinal and
shear reinforcement. However, the user may specify the longitudinal steel, in
which case a column capacity ratio is reported. The column capacity ratio gives
an indication of the load condition with respect to the capacity of the column.
The biaxial column capacity check is based on the generation of consistent
three-dimensional interaction surfaces. It does not use any empirical formulations that extrapolate uniaxial interaction curves to approximate biaxial action.
1-1
Interaction surfaces are generated for user-specified column reinforcing configurations. The column configurations may be rectangular, square, or circular,
with similar reinforcing patterns. The calculation of second order moments,
unsupported lengths, and material partial factors is automated in the algorithm.
Every beam member is designed for flexure, shear, and torsion at output stations
along the beam span.
Input and output data can be presented graphically on the model, in tables, or on
the calculation sheet prepared for each member. For each presentation method,
the data is in a format that allows the engineer to quickly study the stress conditions that exist in the structure and, in the event the member reinforcing is not
adequate, aids the engineer in taking appropriate remedial measures, including
altering the design member without rerunning the entire analysis.
1.1
Organization
This manual is designed to help you quickly become productive with the concrete frame design options of Eurocode 2-2004. Chapter 2 provides detailed
descriptions of the Design Prerequisites used for Eurocode 2-2004. Chapter 3
provides detailed descriptions of the code-specific process used for Eurocode
2-2004. Chapter 4 provides a detailed description of the algorithms related to
seismic provisions in the design/check of structures in accordance with EN
1998-1:2004 Eurocode 8. The appendices provide details on certain topics
referenced in this manual.
1.2
Recommended Reading/Practice
It is strongly recommended that you read this manual and review any applicable
Watch & Learn Series tutorials, which can be found on our web site,
www.csiamerica.com, before attempting to design a concrete frame. Additional
information can be found in the on-line Help facility available from within the
programs main menu.
1-2
Organization
Chapter 2
Design Prerequisites
This chapter provides an overview of the basic assumptions, design preconditions, and some of the design parameters that affect the design of concrete
frames.
In writing this manual it has been assumed that the user has an engineering
background in the general area of structural reinforced concrete design and familiarity with the Eurocode 2-2004 design code and the seismic provisions in the
design/check of structures in accordance with EN 1998-1:2004 Eurocode 8.
2.1
Design Load Combinations

The design load combinations are used for determining the various combinations of the load cases for which the structure needs to be designed/checked. The
load combination factors to be used vary with the selected design code. The load
combination factors are applied to the forces and moments obtained from the
associated load cases and are then summed to obtain the factored design forces
and moments for the load combination.
For multi-valued load combinations involving response spectrum, time history,
moving loads and multi-valued combinations (of type enveloping, square-root
of the sum of the squares or absolute) where any correspondence between interacting quantities is lost, the program automatically produces multiple sub
2-1
combinations using maxima/minima permutations of interacting quantities.

Separate combinations with negative factors for response spectrum cases are not
required because the program automatically takes the minima to be the negative
of the maxima for response spectrum cases and the previously described permutations generate the required sub combinations.
When a design combination involves only a single multi-valued case of time
history or moving load, further options are available. The program has an option
to request that time history combinations produce sub combinations for each
time step of the time history. Also, an option is available to request that moving
load combinations produce sub combinations using maxima and minima of each
design quantity but with corresponding values of interacting quantities.
For normal loading conditions involving static dead load, live load, wind load,
and earthquake load, or dynamic response spectrum earthquake load, the program has built-in default loading combinations for each design code. These are
based on the code recommendations and are documented for each code in the
corresponding manual.
For other loading conditions involving moving load, time history, pattern live
loads, separate consideration of roof live load, snow load, and so on, the user
must define design loading combinations either in lieu of or in addition to the
default design loading combinations.
The default load combinations assume all static load cases declared as dead load
to be additive. Similarly, all cases declared as live load are assumed additive.
However, each static load case declared as wind or earthquake, or response
spectrum cases, is assumed to be non additive with each other and produces
multiple lateral load combinations. Also, wind and static earthquake cases
produce separate loading combinations with the sense (positive or negative)
reversed. If these conditions are not correct, the user must provide the appropriate design combinations.
The default load combinations are included in the design if the user requests
them to be included or if no other user-defined combinations are available for
concrete design. If any default combination is included in design, all default
combinations will automatically be updated by the program any time the design
code is changed or if static or response spectrum load cases are modified.
2-2
Chapter 2 - Design Prerequisites
Live load reduction factors can be applied to the member forces of the live load
case on an element-by-element basis to reduce the contribution of the live load to
the factored loading.
The user is cautioned that if moving load or time history results are not requested
to be recovered in the analysis for some or all of the frame members, the effects
of those loads will be assumed to be zero in any combination that includes them.
2.2
Design and Check Stations

For each load combination, each element is designed or checked at a number of
locations along the length of the element. The locations are based on equally
spaced output stations along the clear length of the element. The number of
output stations in an element is requested by the user before the analysis is
performed. The user can refine the design along the length of an element by
requesting more output stations.
2.3
Identifying Beams and Columns

In the program, all beams and columns are represented as frame elements, but
design of beams and columns requires separate treatment. Identification for a
concrete element is accomplished by specifying the frame section assigned to
the element to be of type beam or column. If any brace member exists in the
frame, the brace member also would be identified as a beam or a column element, depending on the section assigned to the brace member.
2.4
Design of Beams
In the design of concrete beams, in general, the program calculates and reports
the required areas of reinforcing steel for flexure, shear, and torsion based on the
beam moments, shears, load combination factors, and other criteria, which are
described in detail in Chapter 3 and 4 (seismic). The reinforcement requirements
are calculated at a user-defined number of stations along the beam span.
All beams are designed for major direction flexure, shear, and torsion only.
Effects resulting from any axial forces and minor direction bending that may
exist in the beams must be investigated independently by the user.
Design and Check Stations
2-3
In designing the flexural reinforcement for the major moment at a particular

station of a particular beam, the steps involve the determination of the maximum
factored moments and the determination of the reinforcing steel. The beam
section is designed for the maximum positive and maximum negative factored
moment envelopes obtained from all of the load combinations. Negative beam
moments produce top steel. In such cases, the beam is always designed as a
rectangular section. Positive beam moments produce bottom steel. In such cases,
the beam may be designed as a rectangular beam or a T-beam. For the design of
flexural reinforcement, the beam is first designed as a singly reinforced beam. If
the singly reinforced beam is not adequate, the required compression reinforcement is calculated.
In designing the shear reinforcement for a particular beam for a particular set of
loading combinations at a particular station because of beam major shear, the
steps involve the determination of the factored shear force, the determination of
the shear force that can be resisted by concrete, and the determination of any
reinforcement steel required to carry the balance.
2.5
Design of Columns
In the design of the columns, the program calculates the required longitudinal
steel, or if the longitudinal steel is specified, the column stress condition is
reported in terms of a column capacity ratio, which is a factor that gives an
indication of the load condition of the column with respect to the capacity of the
column. The design procedure for the reinforced concrete columns of the
structure involves the following steps:
Generate axial force-biaxial moment interaction surfaces for all of the different concrete section types in the model.
Check the capacity of each column for the factored axial force and bending
moments obtained from each loading combination at each end of the column. This step is also used to calculate the required steel reinforcement (if
none was specified) that will produce a column capacity ratio of 1.0.
The generation of the interaction surface is based on the assumed strain and
stress distributions and other simplifying assumptions. These stress and strain
distributions and the assumptions are documented in Chapter 3.
2-4
Design of Columns
Chapter 2 - Design Prerequisites
The shear reinforcement design procedure for columns is very similar to that for
beams, except that the effect of the axial force on the concrete shear capacity is
considered.
2.6
P-Delta Effects
The program design process requires that the analysis results include P-Delta
effects. For the individual member stability effects, the first order analysis
moments are increased with additional second order moments, as documented in
Chapter 3. As an alternative, the user can turn off the calculation of second order
moments for individual member stability effects. If this calculation is turned off,
the user should apply another method, such as equivalent lateral loading or
P-Delta analysis with vertical members divided into at least two segments, to
capture the member stability effects in addition to the global P-Delta effects.
Users of the program should be aware that the default analysis option is that
P-Delta effects are not included. The user can include P-Delta analysis and set
the maximum number of iterations for the analysis. The default number of
iteration for P-Delta analysis is 1. Further details about P-Delta analysis are
provided in Appendix A of this design manual.
2.7
Element Unsupported Lengths

To account for column slenderness effects, the column unsupported lengths are
required. The two unsupported lengths are l33 and l22. These are the lengths
between support points of the element in the corresponding directions. The
length l33 corresponds to instability about the 3-3 axis (major axis), and l22 corresponds to instability about the 2-2 axis (minor axis).
Normally, the unsupported element length is equal to the length of the element,
i.e., the distance between END-I and END-J of the element. The program,
however, allows users to assign several elements to be treated as a single
member for design. This can be accomplished differently for major and minor
bending, as documented in Appendix B.
The user has options to specify the unsupported lengths of the elements on an
element-by-element basis.
P-Delta Effects
2-5
2.8
Choice of Input Units

Imperial, as well as SI and MKS metric units can be used for input and output.
The codes are based on a specific system of units. The Eurocode 2-2004 design
code is published in Newton-millimeter-second units and all equations and descriptions presented in the Design Process chapter correspond to these units.
However, any system of units can be used to define and design a structure in the
program.
2-6
Choice of Input Units
Chapter 3
Design Process
This chapter provides a detailed description of the code-specific algorithms used

in the design of concrete frames when the Eurocode 2-2004 code has been selected. For simplicity, all equations and descriptions presented in this chapter
correspond to Newton-millimeter-second units unless otherwise noted. It also
should be noted that this section describes the implementation of the CEN Default version of Eurocode 2-2004, without a country specific National Annex.
Where Nationally Determined Parameters [NDPs] are to be considered, this is
highlighted in the respective section by the notation [NDP].
3.1
Notation
The various notations used in this chapter are described herein:
Ac
Area of concrete used to determine shear stress, mm2
Ag
Gross area of concrete, mm2
Ak
Area enclosed by centerlines of connecting walls for torsion, mm2
As
Area of tension reinforcement, mm2
As
Area of compression reinforcement, mm2
3-1
3-2
Asl
Area of longitudinal torsion reinforcement, mm2
At /s
Area of transverse torsion reinforcement (closed stirrups) per unit

length of the member, mm2/mm
Asw /s
Area of shear reinforcement per unit length of the member,

mm2/mm
Ec
Modulus of elasticity of concrete, MPa
Es
Modulus of elasticity of reinforcement, assumed as 200 GPa
Ig
Moment of inertia of gross concrete section about centroidal axis,

neglecting reinforcement, mm4
M01
Smaller factored end moment in a column, N-mm
M02
Larger factored end moment in a column, N-mm
MEd
Design moment, including second order effects to be used in design, N-mm
M0Ed
Equivalent first order end moment (EC2 5.8.8.2), N-mm
M2
Second order moment from the Nominal Curvature method (EC2

5.8.8), N-mm
M22
First order factored moment at a section about 2-axis, N-mm
M33
First order factored moment at a section about 3-axis, N-mm
NB
Buckling load, N
NEd
Factored axial load at a section, N
TEd
Factored torsion at a section, N-mm
VEd
Factored shear force at a section, N
VRd,c
Design shear resistance without shear reinforcement, N
VRd,max
Shear force that can be carried without crushing of the notional

concrete compressive struts, N
Depth of compression block, mm
amax
Maximum allowed depth of compression block, mm
Width of member, mm
Notation
Chapter 3 - Design Process
bf
Effective width of flange (T-beam section), mm
bw
Width of web (T-beam section), mm
Distance from compression face to tension reinforcement, mm
Concrete cover-to-center of reinforcing, mm
ds
Thickness of slab/flange (T-beam section), mm
e2
Deflection due to curvature for the Nominal Curvature method

(EC2 5.8.8), mm
ei
Eccentricity to account for geometric imperfections (EC2 5.2),

mm
emin
Minimum eccentricity (EC2 6.1), mm
fcd
Design concrete compressive strength (EC 3.1.6), MPa
fctm
Mean value of axial tensile strength of concrete, MPa
fyd
Design yield strength of reinforcement (EC2 3.2), MPa
Overall depth of a column section, mm
l0
Member effective length, mm
lu
Member unsupported length, mm
Radius of gyration of column section, mm
tef
Effective wall thickness for torsion, mm
Outer perimeter of cross-section, mm
uk
Outer perimeter of area Ak, mm
Depth to neutral axis, mm
cc
Material coefficient taking account of long-term effects on the

compressive strength (EC2 3.1.6)
ct
Material coefficient taking account of long-term effects on the

tensile strength (EC2 3.1.6)
lcc
Light-weight material coefficient taking account of long-term

effects on the compressive strength (EC2 11.3.5)
Notation
3-3
3.2
lct
Light-weight material coefficient taking account of long-term

effects on the tensile strength (EC2 11.3.5)
Strain in concrete
cu2
Ultimate strain allowed in extreme concrete fiber (0.0035

mm/mm)
Strain in reinforcing steel
Material partial factor for concrete (EC2 2.4.2.4)
Material partial factor for steel (EC2 2.4.2.4)
Factor defining effective height of concrete stress block (EC2

3.1.7)
Factor defining effective strength of concrete stress block (EC2

3.1.7)
Angle between concrete compression strut and member axis

perpendicular to the shear force
Inclination due to geometric imperfections (EC2 5.2), ratio
Basic inclination for geometric imperfections (EC2 5.2), ratio
Assumptions / Limitations
The following general assumptions and limitations exist for the current implementation of Eurocode 2-2004 within the program. Limitations related to
specific parts of the design are discussed in their relevant sections.
3-4
Design of plain or lightly reinforced concrete sections is not handled.
Design of prestressed or post-tensioned sections currently is not handled.
The serviceability limit state currently is not handled.
Design for fire resistance currently is not handled.
By default, the Persistent & Transient design situation (EC2 Table 2.1N) is
considered. Other design situations can be considered and may require
modification of some of the concrete design preference values.
Assumptions / Limitations
3.3
It is assumed that the structure being designed is a building type structure.

Special design requirements for special structure types (such as bridges,
pressure vessels, offshore platforms, liquid-retaining structures, and the
like) currently are not handled.
It is assumed that the load actions are based on Eurocode 1.
The program works with cylinder strength as opposed to cube strength.
The program does not check depth-to-width ratios (EC2 5.3.1) or effective
flange widths for T-beams (EC2 5.3.2). The user needs to consider these
items when defining the sections.
It is assumed that the user will consider the maximum concrete strength
limit, Cmax, specified in the design code (EC2 3.1.2(3)).
It is assumed that the cover distances input by the user satisfy the minimum
cover requirements (EC2 4.4.1.2).
The design value of the modulus of elasticity of steel reinforcement, Es, is

assumed to be 200 GPa (EC2 3.2.7(4)).

The design load combinations are the various combinations of the prescribed
load cases for which the structure is to be checked. The program creates a
number of default design load combinations for a concrete frame design. Users
can add their own design load combinations as well as modify or delete the
program default design load combinations. An unlimited number of design load
combinations can be specified.
To define a design load combination, simply specify one or more load patterns,
each with its own scale factor. The scale factors are applied to the forces and
moments from the load cases to form the design forces and moments for each
design load combination. There is one exception to the preceding. For spectral
analysis modal combinations, any correspondence between the signs of the
moments and axial loads is lost. The program uses eight design load combinations for each such loading combination specified, reversing the sign of axial
loads and moments in major and minor directions.
3-5
As an example, if a structure is subjected to dead load, D, and live load, L, only,

the Eurocode 2-2004 design check would require two design load combinations
only. However, if the structure is subjected to wind, earthquake, or other loads,
numerous additional design load combinations may be required.
The program allows live load reduction factors to be applied to the member
forces of the reducible live load case on a member-by-member basis to reduce
the contribution of the live load to the factored responses.
The design load combinations are the various combinations of the load cases for
which the structure needs to be checked. Eurocode 0-2002 allows load combinations to be defined based on EC0 Eq. 6.10 or the less favorable EC0 Eqs. 6.10a
and 6.10b [NDP].
G , j Gk , j
G , j Gk , j
+ P P + Q ,1Qk ,1 +
j 1
Q ,i 0,i Qk ,i
(EC0 Eq. 6.10)
i >1
+ P P + Q ,1 0,1Qk ,1 +
j 1
Q ,i 0,i Qk ,i
(EC0 Eq. 6.10a)
i >1
j G , j Gk , j
+ P P + Q ,1Qk ,1 +
j 1
Q ,i 0,i Qk ,i
(EC0 Eq. 6.10b)
i >1
Load combinations considering seismic loading are automatically generated

based on EC0 Eq. 6.12b.
k, j
+ P + AEd +
j 1
2,i Qk ,i
(EC0 Eq. 6.12b)
i >1
For this code, if a structure is subjected to dead (D), live (L), wind (W), and
earthquake (E) loads, and considering that wind and earthquake forces are reversible, the following load combinations need to be considered if equation 6.10
is specified for generation of the load combinations (EC0 6.4.3):
3-6
Gj,sup D
(EC0 Eq. 6.10)
Gj,supD + Q,1 L
(EC0 Eq. 6.10)
Gj,inf D Q,1 W
Gj,sup D Q,1 W
(EC0 Eq. 6.10)

(EC0 Eq. 6.10)
Gj,sup D + Q,1 L Q,i 0,i W

Gj,sup D Q,1 W + Q,i 0,i L
D 1.0E
D 1.0E + 2,i L
(EC0 Eq. 6.10)

(EC0 Eq. 6.10)
(EC0 Eq. 6.12b)
If the load combinations are specified to be generated from the maximum of

EC0 Eqs. 6.10a and 6.10b, the following load combinations from both equations
are considered in the program.
Gj,sup D
Gj,sup D
(EC0 Eq. 6.10a)

(EC0 Eq. 6.10b)
Gj,supD + Q,1 0,1 L

Gj,supD + Q,1 L
(EC0 Eq. 6.10a)

(EC0 Eq. 6.10b)
Gj,inf D Q,1 0,1 W

Gj,sup D Q,1 0,1 W
Gj,inf D Q,1 W
Gj,sup D Q,1 W
(EC0 Eq. 6.10a)

(EC0 Eq. 6.10a)
(EC0 Eq. 6.10b)
(EC0 Eq. 6.10b)
Gj,sup D + Q,1 0,1 L Q,i 0,i W

Gj,sup D Q,1 0,1 W + Q,i 0,i L
Gj,sup D + Q,1 L Q,i 0,i W
Gj,sup D Q,1 W + Q,i 0,i L
(EC0 Eq. 6.10a)

(EC0 Eq. 6.10a)
(EC0 Eq. 6.10b)
(EC0 Eq. 6.10b)
D 1.0E
D 1.0E + 2,i L
(EC0 Eq. 6.12b)
For both sets of load combinations, the variable values for the CEN Default
version of the load combinations are defined in the list that follows. Values for
other countries, as determined from their National Annex, are included in
Appendix E.
Gj,sup = 1.35
(EC0 Table A1.2(B))
Gj,inf = 1.00
(EC0 Table A1.2(B))
3-7
Q,1 = 1.5
(EC0 Table A1.2(B))
0,i = 0.7 (live load, assumed not to be storage)
(EC0 Table A1.1)
0,i = 0.6 (wind load)
(EC0 Table A1.1)
= 0.85
2,i = 0.3 (assumed to be office/residential space)
(EC0 Table A1.2(B))

(EC0 Table A1.1)
Depending on the selection made in the design preferences, one of the preceding
two sets of load combinations also makes up the default design load combinations in the program whenever the Eurocode 2-2004 design code is used. The
user should apply other appropriate design load combinations if roof live load is
separately treated, or if other types of loads are present. PLL is the live load
multiplied by the Pattern Live Load Factor. The Pattern Live Load Factor can be
specified in the Preferences.
When using the Eurocode 2-2004 design code, the program design assumes that
a P-Delta analysis has been performed.
3.4
Column Design
The program can be used to check column capacity or to design columns. If the
geometry of the reinforcing bar configuration of the concrete column section has
been defined, the program can check the column capacity. Alternatively, the
program can calculate the amount of reinforcing required to design the column
based on a provided reinforcing bar configuration. The reinforcement requirements are calculated or checked at a user-defined number of output stations
along the column height. The design procedure for reinforced concrete columns
involves the following steps:
3-8
Generate axial force-biaxial moment interaction surfaces for all of the different concrete section types of the model. A typical biaxial interaction diagram is shown in Figure 3-1. For reinforcement to be designed, the
program generates the interaction surfaces for the range of allowable reinforcement from a minimum of 0.2 percent [NDP] to a maximum of 4 percent
[NDP] (EC2 9.5.2).
Column Design
Calculate the capacity ratio or the required reinforcement area for the
factored axial force and biaxial (or uniaxial) bending moments obtained
from each load combination at each output station of the column. The target
capacity ratio is taken as the Utilization Factor Limit when calculating the
required reinforcing area.
Design the column shear reinforcement.
The following four sections describe in detail the algorithms associated with this
process.
3.4.1 Generation of Biaxial Interaction Surfaces

The column capacity interaction volume is numerically described by a series of
discrete points that are generated on the three-dimensional interaction failure
surface. In addition to axial compression and biaxial bending, the formulation
allows for axial tension and biaxial bending considerations. A typical interaction
surface is shown in Figure 3-1.
The coordinates of the points on the failure surface are determined by rotating a
plane of linear strain in three dimensions on the column section, as shown in
Figure 3-2. The linear strain diagram limits the maximum concrete strain, c, at
the extremity of the section to 0.0035 (EC2 Table 3.1).
The formulation is based consistently upon the general principles of ultimate
strength design (EC2 6.1).
The stress in the steel is given by the product of the steel strain and the steel
modulus of elasticity, sEs, and is limited to the yield stress of the steel, fyd (EC2
3.2.7). The area associated with each reinforcing bar is assumed to be placed at
the actual location of the center of the bar, and the algorithm does not assume
any further simplifications with respect to distributing the area of steel over the
cross-section of the column, as shown in Figure 3-2.
The concrete compression stress block is assumed to be rectangular, with an
effective strength of fcd (EC2 3.1.7) and effective height of x, as shown in
Figure 3-3, where is taken as:
= 1.0 for fck 50 MPa
(EC2 Eq. 3.21)
Column Design
3-9
Figure 3-1 A typical column interaction surface
= 1.0 (fck 50)/200 for 50 < fck 90 MPa
(EC2 Eq. 3.22)
and is taken as:

= 0.8 for fck 50 MPa
(EC2 Eq. 3.19)
= 0.8 (fck 50)/400 for 50 < fck 90 MPa
(EC2 Eq. 3.20)
The interaction algorithm provides correction to account for the concrete area
that is displaced by the reinforcement in the compression zone. The depth of the
equivalent rectangular block is further referred to as a, such that:
a=x
(EC2 3.1.7)
where x is the depth of the stress block in compression, as shown in Figure 3-3.
3 - 10
Column Design
Figure 3-2 Idealized strain distribution for generation of interaction surface
The effect of the material partial factors, c and s [NDPs], and the material coefficients, cc, ct, lcc, and lct [NDPs], are included in the generation of the
interaction surface (EC2 3.1.6).
Default values for c, s, cc, ct, lcc, and lct are provided by the program but can
be overwritten using the Preferences.
Column Design
3 - 11
fcd
cu 3
d'
s1
Concrete Section
C s1
C
Cs
s3
Ts 3
s4
Ts 4
Strain Diagram
a = x
Stress Diagram
Figure 3-3 Idealization of stress and strain distribution in a column section
3.4.2 Calculate Column Capacity Ratio

The column capacity ratio is calculated for each design load combination at each
output station of each column. The following steps are involved in calculating
the capacity ratio of a particular column, for a particular design load combination, at a particular location:
3 - 12
Determine the factored first order moments and forces from the load cases
and the specified load combination factors to give Ned, M22, and M33.
Determine the second order moment based on the chosen Second Order
Method [NDP], which can be either Nominal Stiffness (EC2 5.8.7) or
Nominal Curvature (EC2 5.8.8) and can be changed using the Preferences.
There is also a None option if the user wants to explicitly ignore second
order effects within the design calculations. This may be desirable if the
second order effects have been simulated with equivalent loads or if a
P-Delta analysis has been undertaken and each column member is divided
into at least two elements, such that M22 and M33 already account for the
second order effects.
Column Design
Add the second order moments to the first order moments if the column is
determined to be slender (EC2 5.8.3.1). Determine whether the point,
defined by the resulting axial load and biaxial moment set, lies within the
interaction volume.
The following three sections describe in detail the algorithms associated with
this process.
3.4.2.1 Determine Factored Moments and Forces

The loads for a particular design load combination are obtained by applying the
corresponding factors to all of the load cases, giving NEd, M22, and M33. These
first order factored moments are further increased to account for geometric
imperfections (EC2 5.2). The eccentricity to account for geometric imperfections, ei, is defined as:
ei = i l0 2
(EC2 Eq. 5.2)
where l0 is the effective length of the member and i is an inclination, defined as

a ratio as:
i = 0 h m
(EC2 Eq. 5.1)
where m is a reduction factor for the number of members, taken as 1 in the

program for isolated members, h is a reduction factor for length, taken as
2 l , and 0 [NDP] is the basic inclination, defined as a ratio, and can be
overwritten in the Preferences. The resulting geometric imperfection moments,
are calculated as:
Mi2 = ei2 NEd
Mi3 = ei3 NEd
where ei shall be taken greater than or equal to the code specified minimum
eccentricity emin (EC2 6.2). The minimum eccentricity, emin, is defined as:
=
emin h 30 20 mm
(EC2 6.1)
The moment generated because of the geometric imperfection eccentricity, or

the min eccentricity if greater, is considered only in a single direction at a time.
Column Design
3 - 13
3.4.2.2 Second Order Moments

The design algorithm assumes that the moments M22 and M32 are obtained from a
second order elastic (P-) analysis or by applying fictitious, magnified horizontal forces following the recommendations of EC2 Annex H. For more information about P- analysis, refer to Appendix A.
The computed moments are further increased for individual column stability
effects, P- (EC2 5.8.5), by computing a moment magnification factor based on
the Nominal Stiffness method (EC2 5.8.7) or computing a nominal second order
moment based on the Nominal Curvature method (EC2 5.8.8).
3.4.2.2.1 Nominal Stiffness Method

The overall design moment, MEd, based on the Nominal Stiffness method is
computed as:
MEd = M0Ed (factor)
(EC2 Eq. 5.31)
where M0Ed is defined as:

M0Ed = M0e + Mi
M0e = 0.6 M02 + 0.4 M01 0.4 M02
(EC2 Eq. 5.32)
M02 and M01 are the moments at the ends of the column, and M02 is numerically
larger than M01. M O1 M O 2 is positive for single curvature bending and negative
for double curvature bending. The preceding expression of M0e is valid if there is
no transverse load applied between the supports.
The moment magnification factor associated with the major or minor direction
of the column is defined as:
factor = 1 + ( N B N Ed ) 1
(EC2 Eq. 5.28)
The factor depends on the distribution of the first and second order moments
and is defined as:
= 2 c0 ,
3 - 14
Column Design
(EC2 Eq. 5.29)
where c0 is a coefficient that depends on the distribution of the first order moment and is taken equal to 8, which is consistent with a constant first order
moment. The term NB is the buckling load and is computed as:
NB =
2 EI
(l lu ) 2
where l is conservatively taken as 1; however, the program allows the user to

overwrite this value. The unsupported length of the column for the direction of
bending considered is defined as lu. The two unsupported lengths are l22 and l33,
corresponding to instability in the minor and major directions of the object,
respectively, as shown in Figure B-1 in Appendix B. These are the lengths
between the support points of the object in the corresponding directions.
Refer to Appendix B for more information about how the program automatically
determines the unsupported lengths. The program allows the user to overwrite
the unsupported length ratios, which are the ratios of the unsupported lengths for
the major and minor axis bending to the overall member length.
When using the stiffness method, the EI associated with a particular column
direction is considered in the design as:
EI = 0.3EcIg
This value neglects creep effects and may be unconservative if significant creep
effects exist.
The additional moment from the Nominal Stiffness method must be a positive
number. Therefore, NEd must be greater than NB. If NEd is found to be less than or
equal to NB, a failure condition is declared.
3.4.2.2.2 Nominal Curvature Method

The overall design moment, MEd, based on the Nominal Curvature method is
computed as:
MEd = M0Ed + M2
(EC2 Eq. 5.31)
where M0Ed is defined as:

M0Ed = M0e + Mi
Column Design
3 - 15
M0e = 0.6 M02 + 0.4 M01 0.4 M02
(EC2 Eq. 5.32)
M02 and M01 are the moments at the ends of the column, and M02 is numerically
larger than M01. M 01 M 02 is positive for single curvature bending and negative
for double curvature bending. The preceding expression of M0e is valid if no
transverse load is applied between the supports.
The additional second order moment associated with the major or minor direction of the column is defined as:
M2 = NEd e2
(EC2 Eq. 5.33)
where NEd is the design axial force, and e2, the deflection due to the curvature, is
defined as:
e2 = (1 r ) lo2 c
(EC2 5.8.8.2(3))
The effective length, lo, is taken equal to l lu. The factor c depends on the curvature distribution and is taken equal to 8, corresponding to a constant first order
moment. The term l r is the curvature and is defined as:
l r = K r K 1 r0
(EC2 Eq. 5.34)
The correction factor, Kr, depends on the axial load and is taken as 1 by default.
The factor K is also taken as 1, which represents the situation of negligible
creep. Both of these factors can be overwritten on a member-by-member basis.
The term 1 r0 is defined as:
1 r0 = yd ( 0.45d )
(EC2 5.8.8.3(1))
The preceding second order moment calculations are performed for major and
minor directions separately.
The additional second order moment, M2 is ignored when the slenderness, is
less than the limiting slenderness specified by the code.
20 A B C
lim =
n
3 - 16
Column Design
(EC2 5.8.3.1(1))
3.4.2.3 Determine Capacity Ratio

As a measure of the load condition of the column, a capacity ratio is calculated.
The capacity ratio is a factor that gives an indication of the load condition of the
column with respect to the load capacity of the column.
Before entering the interaction diagram to check the column capacity, the second order moments are added to the first order factored loads to obtain NEd,
MEd2, and MEd3. The point (NEd, MEd2, MEd3) is then placed in the interaction space
shown as point L in Figure 3-4. If the point lies within the interaction volume,
the column capacity is adequate. However, if the point lies outside the interaction volume, the column is overloaded.
Figure 3-4 Geometric representation of column capacity ratio
Column Design
3 - 17
This capacity ratio is achieved by plotting the point L and determining the location of point C. Point C is defined as the point where the line OL (if extended
outwards) will intersect the failure surface. This point is determined by
three-dimensional linear interpolation between the points that define the failure
surface, as shown in Figure 3-4. The capacity ratio, CR, is given by the ratio
OL OC .
If OL = OC (or CR = 1), the point lies on the interaction surface and the
column is loaded to capacity.
If OL < OC (or CR < 1), the point lies within the interaction volume and
the column capacity is adequate.
If OL > OC (or CR > 1), the point lies outside the interaction volume and
the column is overloaded.
The maximum of all the values of CR calculated from each design load combination is reported for each check station of the column, along with the controlling NEd, MEd2, and MEd3 set and associated design load combination name.
3.4.3 Design Longitudinal Reinforcement

If the reinforcing area is not defined, the program computes the required reinforcement that will give a column capacity ratio equal to the Utilization Factor
Limit, which is set to 0.95 by default.
3.4.4 Design Column Shear Reinforcement

The shear reinforcement is designed for each design combination in the major
and minor directions of the column. The following steps are involved in designing the shear reinforcing for a particular column, for a particular design load
combination resulting from shear forces in a particular direction:
3 - 18
Determine the design forces acting on the section, NEd and VEd. Note that NEd
is needed for the calculation of VRd,c.
Determine the design shear resistance of the member without shear reinforcement, VRd,c.
Column Design
Determine the maximum design shear force that can be carried without
crushing of the notional concrete compressive struts, VRd,max.
Determine the required shear reinforcement as area per unit length, Asw s.
process.
3.4.4.1 Determine Design Shear Force

In the design of the column shear reinforcement of concrete frames, the forces
for a particular design load combination, namely, the column axial force, NEd,
and the column shear force, VEd, in a particular direction are obtained by factoring the load cases with the corresponding design load combination factors.
3.4.4.2 Determine Design Shear Resistance

Given the design force set NEd and VEd, the shear force that can be carried without
requiring design shear reinforcement, VRd,c, is calculated as:
VRd,c = [CRd,c k (100 l fck)1/3 + k1 cp] bwd
(EC2 Eq. 6.2.a)
with a minimum of:

VRd,c = (vmin + k1 cp) bwd
(EC2 Eq. 6.2.b)
where fck is in MPa, and k, l, and cp are calculated as:
k =1+
l =
200
2.0 (d is in mm)
d
As
0.02
bw d
=
cp N Ed Ac < 0.2 f cd (in MPa)
(EC2 6.2.2(1))
(EC2 6.2.2(1))
(EC2 6.2.2(1))
The effective shear area, Ac, is shown shaded in Figure 3-6. For circular columns, Ac is taken to be equal to the gross area of the section. The factor k1 = 0.15
[NDP] and the values of CRd,c [NDP] and vmin [NDP] are determined as:
Column Design
3 - 19
C Rd ,c = 0.18 c
(EC2 6.2.2(1))
vmin = 0.035 k3/2 fck1/2
(EC2 Eq. 6.3N)
3.4.4.3 Determine Maximum Design Shear Force

To prevent crushing of the concrete compression struts, the design shear force
VEd is limited by the maximum sustainable design shear force, VRd,max. If the design shear force exceeds this limit, a failure condition occurs. The maximum
sustainable shear force is defined as:
VRd ,max = cwbw z v1 f cd ( cot + tan )
d'
DIRECTION
OF SHEAR
FORCE
(EC2 Eq. 6.9)
A cv
RECTANGULAR
d'
DIRECTION
OF SHEAR
FORCE
A cv
SQUARE WITH CIRCULAR REBAR
d'
DIRECTION
OF SHEAR
FORCE
A cv
CIRCULAR
Figure 3-6 Shear stress area, Ac
3 - 20
Column Design
The coefficient cw [NDP] takes account of the state of stress in the compression
chord and is taken equal to 1, which is recommended for non-prestressed
structures. The strength reduction factor for concrete cracked in shear, v1 [NDP],
is defined as:
=
v1 0.6 [1 fck 250 ] (fck is in MPa)
(EC2 Eq. 6.6N)
The inner lever arm distance, z, is approximated as 0.9d. The angle between the
concrete compression strut and the column axis perpendicular to the shear force
is defined as and taken as 45 degrees. EC2 allows to be taken between 21.8
and 45 degrees. The program assumes the conservative value of 45 degrees.
3.4.4.4 Determine Required Shear Reinforcement

If VEd is greater than VRd,c and less than VRd,max, the required shear reinforcement
in the form of stirrups or ties per unit spacing, Asw s , is calculated as:
Asw
VEd
=
s
zf ywd cot
(EC2 Eq. 6.8)
In the preceding expressions, for a rectangular section, bw is the width of the

column, d is the effective depth of the column, and Ac is the effective shear area,
which is equal to bwd. For a circular section, bw is replaced with D, which is the
external diameter of the column, d is replaced with 0.8D, and Ac is replaced with
the gross area D 2 4.
The maximum of all of the calculated Asw s values, obtained from each design
load combination, is reported for the major and minor directions of the column,
along with the controlling combination name.
The column shear reinforcement requirements reported by the program are
based purely on shear strength consideration. Any minimum stirrup requirements to satisfy spacing considerations or transverse reinforcement volumetric
considerations must be investigated independently by the user.
Column Design
3 - 21
3.5
Beam Design
In the design of concrete beams, the program calculates and reports the required
areas of steel for flexure and shear based on the beam moments, shear forces,
torsions, design load combination factors, and other criteria described in the text
that follows. The reinforcement requirements are calculated at a user-defined
number of output stations along the beam span.
All beams are designed for major direction flexure, shear, and torsion only.
Effects resulting from any axial forces and minor direction bending that may
exist in the beams must be investigated independently by the user.
The beam design procedure involves the following steps:
Design flexural reinforcement
Design shear reinforcement
Design torsion reinforcement
3.5.1 Design Beam Flexural Reinforcement

The beam top and bottom flexural reinforcement is designed at output stations
along the beam span. The following steps are involved in designing the flexural
reinforcement for the major moment for a particular beam, at a particular
section:
Determine the maximum factored moments
Determine the required reinforcing steel
3.5.1.1 Determine Factored Moments

In the design of flexural reinforcement of concrete beams, the factored moments
for each design load combination at a particular beam section are obtained by
factoring the corresponding moments for different load cases with the corresponding design load combination factors.
The beam section is then designed for the factored moments obtained from each
of the design load combinations. Positive moments produce bottom steel. In
such cases, the beam may be designed as a rectangular or a T-beam section.
3 - 22
Beam Design
Negative moments produce top steel. In such cases, the beam is always designed
as a rectangular section.
3.5.1.2 Determine Required Flexural Reinforcement

In the flexural reinforcement design process, the program calculates both the
tension and compression reinforcement. Compression reinforcement is added
when the applied design moment exceeds the maximum moment capacity of a
singly reinforced section. The user can avoid the need for compression reinforcement by increasing the effective depth, the width, or the grade of concrete.
The design procedure is based on a simplified rectangular stress block, as shown
in Figure 3-7 (EC2 3.1.7(3)). When the applied moment exceeds the moment
capacity, the area of compression reinforcement is calculated on the assumption
that the additional moment will be carried by compression and additional tension
reinforcement.
The design procedure used by the program for both rectangular and flanged
sections (T-beams) is summarized in the following subsections. It is assumed
that the design ultimate axial force is negligible, hence all beams are designed
ignoring axial force.
cu 3
As
d'
f s
Beam Section
Cs
a = x
As
fcd
Strain Diagram
Ts
Tc
Stress Diagram
Figure 3-7 Rectangular beam design
Beam Design
3 - 23
In designing for a factored negative or positive moment, MEd (i.e., designing top
or bottom steel), the effective strength and depth of the compression block are
given by fcd and x (see Figure 3-7) respectively, where:
= 0.8 for fck 50 MPa,
(EC2 Eq. 3.19)
= 0.8 ( fck 50 ) 400 for 50 < fck 90 MPa,
(EC2 Eq. 3.20)
= 1.0 for fck 50 MPa,
(EC2 Eq. 3.21)
= 1.0 ( fck 50 ) 200 for 50 < fck 90 MPa,
(EC2 Eq. 3.22)
where x is the depth of the neutral axis, is a factor defining the effective height
of the compression zone, and is a factor defining the effective strength.
The limiting value of the ratio of the neutral axis depth at the ultimate limit state
to the effective depth, (x/d)lim, is expressed as a function of the ratio of the redistributed moment to the moment before redistribution, , as follows:
( x d )lim = ( k1 )
k2 for fck 50 MPa
(EC2 Eq. 5.10a)
( x d )lim = ( k3 )
k4 for fck > 50 MPa
(EC2 Eq. 5.10b)
No redistribution is assumed, such that is assumed to be 1. The four factors, k1,

k2, k3, and k4 [NDPs], are defined as:
k1 = 0.44
(EC2 5.5(4))
k2 = 1.25 ( 0.6 + 0.0014 cu 2 )
(EC2 5.5(4))
k3 = 0.54
(EC2 5.5(4))
k4 = 1.25 ( 0.6 + 0.0014 cu 2 )
(EC2 5.5(4))
where the ultimate strain, cu2 [NDP], is determined from EC2 Table 3.1 as:
cu2 = 0.0035 for fck < 50 MPa
(EC2 Table 3.1)
cu2 = 2.6 + 35 ( 90 fck ) 100 for fck 50 MPa

4
3 - 24
Beam Design
(EC2 Table 3.1)
3.5.1.2.1 Rectangular Beam Flexural Reinforcement

For rectangular beams, the normalized moment, m, and the normalized section
capacity as a singly reinforced beam, mlim, are determined as:
m=
M
bd 2 f cd
x x
mlim = 1
d lim 2 d lim
The reinforcing steel area is determined based on whether m is greater than, less
than, or equal to mlim.
If m mlim, a singly reinforced beam will be adequate. Calculate the normalized steel ratio, , and the required area of tension reinforcement, As, as:
1 2m
= 1
f cd bd
f yd
As =
This area of reinforcing steel is to be placed at the bottom if MEd is positive, or

at the top if MEd is negative.
If m > mlim, compression reinforcement is required. Calculate the normalized
steel ratios, ', lim, and , as:
x
lim = = 1
d lim
' =
1 2 m lim
m mlim
1 d d
= lim + '
where d' is the depth to the compression steel, measured from the concrete
compression face.
Beam Design
3 - 25
Calculate the required area of compression and tension reinforcement, As' and
As, as:
f bd
As' = ' cd
f s
f bd
As = cd
f yd
where fs , the stress in the compression steel, is calculated as:
d
fs = Es c 1
fyd
xlim
As is to be placed at the bottom and As' is to be placed at the top if MEd is positive, and As' is to be placed at the bottom and As is to be placed at the top if MEd
is negative.
3.5.1.2.2 T-Beam Flexural Reinforcement

In designing a T-beam, a simplified stress block, as shown in Figure 3-8, is
assumed if the flange is in compression, i.e., if the moment is positive. If the
moment is negative, the flange is in tension, and therefore ignored. In that case, a
simplified stress block, similar to that shown in Figure 3-8, is assumed on the
compression side.
Flanged Beam Under Negative Moment

In designing for a factored negative moment, MEd (i.e., designing top steel), the
calculation of the reinforcing steel area is exactly the same as described for a
rectangular beam, i.e., no specific T-beam data is used.
Flanged Beam Under Positive Moment

In designing for a factored positive moment, MEd, the program analyzes the
section by considering the depth of the stress block. If the depth of the stress
block is less than or equal to the flange thickness, the section is designed as a
3 - 26
Beam Design
rectangular beam with a width bf. If the stress block extends into the web, additional calculation is required.
For T-beams, the normalized moment, m, and the normalized section capacity as
a singly reinforced beam, mlim, are calculated as:
m=
M
b f d 2 f cd
x x
mlim =
1
d lim 2 d lim
Calculate the normalized steel ratios lim and , as:
x
lim =
d lim
= 1 1 2m
Calculate the maximum depth of the concrete compression block, amax, and the
effective depth of the compression block, a, as:
amax = lim d
a = d
The reinforcing steel area is determined based on whether m is greater than, less
than, or equal to mlim. The maximum allowable depth of the rectangular compression block, amax, is given by:
If a hf , the subsequent calculations for As are exactly the same as previously defined for rectangular beam design. However, in this case, the width
of the beam is taken as bf , as shown in Figure 3-8. Compression reinforcement is required if a > amax.
If a > hf , the calculation for As has two parts. The first part is for balancing
the compressive force from the flange, and the second part is for balancing
the compressive force from the web, as shown in Figure 3-8.
Beam Design
3 - 27
The required reinforcing steel area, As2, and corresponding resistive moment, M2, for equilibrating compression in the flange outstands are calculated as:
As 2 =
(b
bw )h f f cd
f yd
hf
M 2 = As 2 f yd d
2
cu 3
hf
bf
d'
As
f s
Cs
a = x
Cf
x
d
As
fcd
fcd
cw
Ts
Tw
Tf
bw
Beam Section
Strain Diagram
Stress Diagram
Figure 3-8 T-beam design
Now calculate the required reinforcing steel area As1 for the rectangular
section of width bw to resist the remaining moment M1 = MEd M2. The
normalized moment, m1 is calculated as:
m1 =
M1
bw d 2 f cd
The reinforcing steel area is determined based on whether m1 is greater than,

less than, or equal to mlim.
3 - 28
Beam Design
If m1 mlim, a singly reinforced beam will be adequate. Calculate the

normalized steel ratio, 1, and the required area of tension reinforcement, As1, as:
1 2m
1 = 1
f bd
As1 = 1 cd
f yd
If m1 > mlim, compression reinforcement is required. Calculate the

normalized steel ratios, ', lim, and , as:
d lim
lim =
m mlim
1 d d
1 = lim +
where d' is the depth to the compression steel, measured from the
concrete compression face.
Calculate the required area of compression and tension reinforcement,
As and As, as:
f bd
As = ' cd
f s
f bd
As1 = 1 cd
f yd
where fs, the stress in the compression steel, is calculated as:
d
fs = Esc 1
fyd
xlim
Beam Design
3 - 29
The total tensile reinforcement is As = As1 + As2, and the total compression
reinforcement is As. As is to be placed at the bottom and As is to be placed at
the top of the section.
3.5.1.3 Minimum and Maximum Tensile Reinforcement

The minimum flexural tensile steel reinforcement, As,min [NDP], required in a
beam section is given as the maximum of the following two values:
As,min = 0.26 ( fctm f yk ) bt d
(EC2 Eq. 9.1N)
As,min = 0.0013bt d
where bt is the mean width of the tension zone, equal to the web width for
T-beams, and fctm is the mean value of axial tensile strength of the concrete,
calculated as:
fctm = 0.30fck(2/3)
for fck 50 MPa
(EC2 Table 3.1)
fctm = 2.12 ln (1 + fcm 10 )
for fck > 50 MPa
(EC2 Table 3.1)
fcm = fck + 8 MPa

The maximum flexural steel reinforcement, As,max [NDP], permitted as either
tension or compression reinforcement is defined as:
As,max = 0.04Ac
(EC2 9.2.1.1(3))
where Ac is the gross cross-sectional area.
3.5.2 Design Beam Shear Reinforcement

The required beam shear reinforcement is calculated for each design load combination at each output station along the beam length. The following assumptions are made for the design of beam shear reinforcement:
3 - 30
The beam section is assumed to be prismatic. The shear capacity is based on

the beam width at the output station and therefore a variation in the width of
the beam is neglected in the calculation of the concrete shear capacity at
each particular output station.
Beam Design
All shear reinforcement is assumed to be perpendicular to the longitudinal

reinforcement. Inclined shear steel is not handled.
The following steps are involved in designing the shear reinforcement for a
particular output station subjected to beam major shear:
Determine the design value of the applied shear force, VEd.
Determine the design shear resistance of the member without shear reinforcement, VRd,c.
Determine the maximum design shear force that can be carried without
crushing of the notional concrete compressive struts, VRd,max.
Determine the required shear reinforcement as area per unit length, Asw s.
process.
3.5.2.1 Determine Design Shear Force

In the design of the beam shear reinforcement, the shear forces and moments for
a particular design load combination at a particular beam section are obtained by
factoring the associated shear forces and moments with the corresponding design load combination factors.
3.5.2.2 Determine Design Shear Resistance

The shear force that can be carried without requiring design shear reinforcement,
VRd,c, is calculated as:
13
VRd,c = CRd ,c k (100l f ck ) + k1cp bwd
(EC2 Eq. 6.2.a)
with a minimum of:

VRd,c = (vmin + k1 cp) bwd
(EC2 Eq. 6.2.b)
where fck is in MPa, and k, l, and cp are calculated as:
Beam Design
3 - 31
k =1+
l =
200
2.0 (d is in mm)
d
As
0.02
bw d
(EC2 6.2.2(1))
(EC2 6.2.2(1))
cp = NEd /Ac < 0.2fcd (in MPa)
(EC2 6.2.2(1))
The effective shear area, Ac (see Figure 3-6), is taken as bwd. The factor k1 = 0.15
[NDP] and the values of CRd,c [NDP] and vmin [NDP] are determined as:
CRd,c = 0.18 c
(EC2 6.2.2(1))
vmin = 0.035 k3/2 fck1/2
(EC2 Eq. 6.3N)
3.5.2.3 Determine Maximum Design Shear Force

To prevent crushing of the concrete compression struts, the design shear force
VEd is limited by the maximum sustainable design shear force, VRd,max. If the design shear force exceeds this limit, a failure condition occurs. The maximum
sustainable shear force is defined as:
VRd,max = cwbw z v1 f cd ( cot + tan )
(EC2 Eq. 6.9)
The coefficient cw [NDP] takes account of the state of stress in the compression
chord and is taken equal to 1, which is recommended for non-prestressed
structures. The strength reduction factor for concrete cracked in shear, v1 [NDP]
is defined as:
v1 = 0.6 [1 fck 250 ] (fck is in MPa)
(EC2 Eq. 6.6N)
The inner lever arm distance, z, is approximated as 0.9d.

The angle between the concrete compression strut and the beam axis perpendicular to the shear force is defined as . If torsion is significant i.e., TEd > Tcr
where Tcr is defined as:
VEd
=
Tcr TRd ,c 1
VRd ,c
3 - 32
Beam Design
(EC2 Eq. 6.31)
and if the load combination include seismic, the value of is taken as 45.
However, for other cases is optimized using the following relationship:
( cot + tan=
) 0.9 cw v1 f cd vEd
where
21.8 45
3.5.2.4 Determine Required Shear Reinforcement

If VEd is greater than VRd,c and less than VRd,max, the required shear reinforcement
in the form of stirrups or ties per unit spacing, Asw s, is calculated as:
Asw
VEd
=
s
zf ywd cot
(EC2 Eq. 6.8)
The computation of is given in preceding section.

The maximum of all the calculated Asw s values, obtained from each design
load combination, is reported for the beam, along with the controlling combination name. The calculated shear reinforcement must be greater than the
minimum reinforcement ratio of:
w,min = 0.08 fck
f yk
(EC2 Eq. 9.5N)
The beam shear reinforcement requirements reported by the program are based
purely on shear strength considerations. Any minimum stirrup requirements to
satisfy spacing and volumetric consideration must be investigated independently
of the program by the user.
3.5.3 Design Beam Torsion Reinforcement

The torsion reinforcement is designed for each design load combination at a
user-defined number of output stations along the beam span. The following steps
are involved in designing the longitudinal and shear reinforcement for a particular station due to beam torsion:
Determine the factored torsion, TEd.

Beam Design
3 - 33
Determine torsion section properties.
Determine the torsional cracking moment.
Determine the reinforcement steel required.
3.5.3.1 Determine Factored Torsion

In the design of torsion reinforcement of any beam, the factored torsions for each
design load combination at a particular design station are obtained by factoring
the corresponding torsion for different load cases with the corresponding design
load combination factors.
3.5.3.2 Determine Torsion Section Properties

For torsion design, special torsion section properties, including Ak, tef, u, uk, and
zi, are calculated. These properties are described as follows (EC2 6.3).
Ak = Area enclosed by centerlines of the connecting walls, where the
centerline is located a distance of tef 2 from the outer surface
tef = Effective wall thickness
u = Outer perimeter of the cross-section
uk = Perimeter of the area Ak
zi = Side length of wall i, defined as the distance between the intersection points of the wall centerlines
For torsion design of T-beam sections, it is assumed that placing torsion reinforcement in the flange area is inefficient. With this assumption, the flange is
ignored for torsion reinforcement calculation. However, the flange is considered
during calculation of the torsion section properties. With this assumption, the
special properties for a Rectangular beam section are given as follows:
A = bh
Ak = (b tef)(h tef)
u = 2b + 2h
uk = 2(b tef) + 2(h tef)
3 - 34
Beam Design
where, the section dimensions b, h, and tef are shown in Figure 3-9. Similarly, the
special section properties for a T-beam section are given as follows:
A =
bw h + ( b f bw ) ds
Ak = (bf tef)(h tef)

u = 2bf + 2h
uk = 2(bf tef) + 2(h tef)
where the section dimensions bf, bw, h, and ds for a T-beam are shown in
Figure 3-9.
c
b 2c
bf
ds
h 2c
h 2c
c
b
bw 2c
bw
Closed Stirrup in
Rectangular Beam
Closed Stirrup in
T-Beam Section
Figure 3-9 Closed stirrup and section dimensions for torsion design
3.5.3.3 Determine Torsional Cracking Moment

The torsion in the section can be ignored with only minimum shear reinforcement (EC2 9.2.1.1) necessary if the following condition is satisfied:
TEd TRd ,c + VEd VRd ,c 1.0
(EC2 Eq. 6.31)
where TRd,c is the torsional cracking moment, determined as:
Beam Design
3 - 35
TRd,c = fctd tef 2Ak

where tef, and fctd, the design tensile strength, are defined as:
tef = A u
(EC2 6.3.2(1))
f ctd =
ct f ctk 0.05 c
(EC2 Eq. 3.16)
where A is the gross cross-section area, u is the outer circumference of the

cross-section, ct [NDP] is a coefficient, taken as 1.0, taking account of longterm effects on the tensile strength, and fctk0.05 is defined as:
fctk0.05 = 0.7fctm
(EC2 Table 3.1)
3.5.3.4 Determine Torsion Reinforcement

If EC2 Eq. 6.31, as previously defined, is satisfied, torsion can be safely ignored
(EC2 6.3.2(5)). In that case, the program reports that no torsion shear reinforcement is required. However, if the equation is not satisfied, it is assumed that
the torsional resistance is provided by closed stirrups, longitudinal bars, and
compression diagonals.
If torsion reinforcement in the form of closed stirrups is required, the shear due
to this torsion, Vt, is first calculated, followed by the required stirrup area, as:
Vt =
2 ( h tef ) ( TEd Tcon ) 2 Ak
where,
V
Tcon= 1 Ed
V
Rd ,c
TRd ,c
(EC2 6.3.2(5))
At
Vt
=
s zf ywd cot
The required longitudinal reinforcement area for torsion is defined as:
=
Asl
3 - 36
Beam Design
TEd
u
cot k
2 Ak
f yd
(EC2 Eq. 6.28)
where is the angle of the compression struts, as previously defined for beam
shear. In the preceding expressions, is taken as 45. The code allows any value
between 21.8 and 45 (EC2 6.2.3(2)), while the program assumes the conservative value of 45.
An upper limit of the combination of VEd and TEd that can be carried by the section without exceeding the capacity of the concrete struts also is checked using
the following equation.
TEd
TRd ,max
VEd
1.0
VRd ,max
(EC2 Eq. 6.29)
where, TRd,max, the design torsional resistance moment is defined as:

TRd,max = 2cw fcd Ak tef sin cos
(EC2 Eq. 6.30)
The value is defined by EC2 Eq. 6.6N. If the combination of VEd and TEd exceeds this limit, a failure message is declared. In that case, the concrete section
should be increased in size.
The maximum of all the calculated Asl and At s values obtained from each design load combination is reported along with the controlling combination names.
The beam torsion reinforcement requirements reported by the program are based
purely on strength considerations. Any minimum stirrup requirements and longitudinal rebar requirements to satisfy spacing considerations must be investigated independently of the program by the user.
Beam Design
3 - 37
Chapter 4
Seismic Provisions
This chapter provides a detailed description of the algorithms related to seismic

provisions in the design/check of structures in accordance with the "EN 19981:2004 Eurocode 8: Design of Structures for Earthquake Resistance" (EC 8
2004). The code option "Eurocode 2-2004" covers these provisions. The
implementation covers load combinations from "Eurocode 2-2004," which is
described in the section "Design Loading Combination" of Chapter 3. The
loading based on "Eurocode 8-2004" has been described in a separate
document entitled "CSI Lateral Load Manual" (CSI 2009).
For referring to pertinent sections of the corresponding code, a unique prefix is
assigned for each code.
Reference to the Eurocode EN 1990:2001 code is identified with the prefix

"EC0."
Reference to the Eurocode EN 1992-1-1:2004 code is identified with the

prefix "EC2."
Reference to the Eurocode EN 1998-1:2004 code is identified with the prefix "EC8."
4-1
4.1
Notations
The following notations are used in this chapter.
4-2
Ash
Total area of horizontal hoops in a beam-column joint, mm2
Asv,i
Total area of column vertical bars between corner bars in one

direction through a joint, mm2
MRb
Sum of design values of moments of resistance of the beams

framing into a joint in the direction of interest, N-mm
MRc
Sum of design values of the moments of resistance of the columns

framing into a joint in the direction of interest, N-mm
Mi,d
End moment of a beam or column for the calculation of its capacity

design shear, N-mm
MRb,i
Design value of beam moment of resistance at end i, N-mm
MRc,i
Design value of column moment of resistance at end i, N-mm
VEd,max
Maximum acting shear force at the end section of a beam from

capacity design calculation, N
VEd,min
Minimum acting shear force at the end section of a beam from

capacity design calculation, N
Cross-section depth, mm
hc
Cross-sectional depth of the column in the direction of interest, mm
hjc
Distance between extreme layers of the column reinforcement in a

beam-column joint, mm
hjw
Distance between beam top and bottom reinforcement, mm
lcl
Clear length of a beam or a column, mm
qo
Basic value of the behavior factor
Prevailing aspect ratio of the walls of the structural design
Notations
Chapter 4 - Seismic Provisions
Multiplier of the horizontal design seismic action at formation of

the first plastic hinge in the system
Multiplier of the horizontal seismic design action at formation of

the global plastic mechanism
Rd
Model uncertainty factor on the design value of resistance in the

estimation of the capacity design action effects, accounting for various sources of overstrength
Ratio, VEd ,min VEd ,max , between the minimum and maximum acting
shear forces at the end section of a beam
4.2
Curvature ductility factor
Displacement ductility factor
Tension reinforcement ratio
Design Preferences
The concrete frame design Preferences are basic assignments that apply to all
of the concrete frame members. The following steel frame design Preferences
are relevant to the special seismic provisions.
Framing Type
Ignore Seismic Code?
4.3
Overwrites
The concrete frame design Overwrites are basic assignments that apply only to
those elements to which they are assigned. The following steel frame design
overwrite is relevant to the special seismic provisions.
Frame Type
Design Preferences
4-3
4.4
Supported Framing Types

The code (Eurocode 8:2004) now recognizes the following types of framing
systems (EC8 5.2.1(4)). With regard to these framing types, the program has
implemented specifications for the types of framing systems listed.
Framing Type
References
DCH MRF (Ductility Class High Moment-Resisting Frame)
EC8 5.5
DCM MRF (Ductility Class Medium Moment-Resisting Frame)
EC8 5.4
DCL MRF (Ductility Class Low Moment-Resisting Frame)
EC8 5.3
Secondary
The program default frame type is Ductility Class High Moment-Resisting Frame
(DCH MRF). However, that default can be changed in the Preference for all
frames or in the Overwrites on a member-by-member basis. If a frame type
Preference is revised in an existing model, the revised frame type does not apply to frames that have already been assigned a frame type through the Overwrites; the revised Preference applies only to new frame members added to the
model after the Preference change and to the old frame members that were not
assigned a frame type though the Overwrites.
4.5
Member Design
This section describes the special requirements for designing a member.
4.5.1
Ductility Class High Moment-Resisting Frames (DCH MRF)

For this framing system
( qo=
4.5u 1 , u 1= 1.1 1.3) (EC8 5.2.2.2(5),
Table 5.1), the following additional requirements are checked or reported (EC8
5.5).
NOTE: The geometrical constraints and material requirements given in EC8
Section 5.5.1 should be checked independently by the user because the program does not perform those checks.
4-4
Supported Framing Types
4.5.1.1
Design Forces
4.5.1.1.1
Beams
The design values of bending moments and axial forces are obtained from the
analysis of the structure for the seismic design situation in accordance with
EC0 section 6.4.3.4, taking into account second order effects in accordance
with EC0 4.4.2.2 and the capacity design requirements of 5.2.3.3(2) (EC8
5.5.2). The design values for shear forces of primary seismic beams and columns are determined in accordance with EC8 5.5.2.1 and EC8 5.5.2.2, respectively.
In primary seismic beams, the design shear forces are determined in accordance with the capacity design rule, on the basis of the equilibrium of the beam
under (a) the transverse load acting on it in the seismic design situation and (b)
end moments Mi,d (with i = 1,2 denoting the end sections of the beam), corresponding to plastic hinge formation for positive and negative directions of
seismic loading. The plastic hinges should be taken to form at the ends of the
beams or (if they form there first) in the vertical elements connected to the
joints into which the beam ends frame (see Figure 4-1) (EC8 5.5.2.1,
5.4.2.2(1)P).
g + 2q
Rd M Rh ,1 ( M Rc M Rb )
Rd M + Rh,2
M Rc
M Rd
M Rc
M Rb > M Rc
lc1
M Rc
M Rb < M Rc
Figure 4-1 Capacity Design Shear Force for beams
The above condition has been implemented as follows (EC8 5.5.2.1,

5.4.2.2(2)P, 5.4.2.2(3)P).
Member Design
4-5

a) At end section i, two values of the acting shear force should be calculated,
i.e. the maximum VEd,max,i and the minimum VEd,min,i corresponding to the
maximum positive and the maximum negative end moments Mi,d that can
develop at ends 1 and 2 of the beam.
max Vi ,d
Rd M Rd
,bi min 1,
Rd ,c
Rd ,b
+
+ M Rd
,bj min 1,
M
M
Rd ,c
Rd ,b
lcl
Rd
min Vi ,d
M
M
+
M Rd
,bi min 1,
M
M
Rd ,c
Rd ,b
+ M Rd
,bj min 1,
lcl
M
M
Rd ,c
Rd ,b
+ Vg + 2 q ,o
+ Vg + 2 q ,o
As the moments and shears on the right-hand side of equations presented

above are positive, the outcome may be positive or negative. If it is positive, the shear at any section will not change the sense of action despite the
cyclic nature of seismic loading; if it is negative, the shear does change
sense. The ratio
min Vi ,d
i =
max Vi ,d
is used in the dimensioning of shear reinforcement of DCH beams as a
measure of reversal of the shear force at end i (similarly at end j).
b) End moments Mi,d is determined as follows:
M i ,d = Rd M Rb ,i min 1,
M
M
Rc
Rb
(EC8 Eq. 5.8)
where
Rd is the factor accounting for possible overstrength because of steel

strain hardening, which in the case of DCH beams is taken as equal to 1.2;
4-6
Member Design
MRb,i is the design value of the beam moment of resistance at end i in the
sense of the seismic bending moment under the considered sense of the
seismic action;
MRc and MRb are the sum of the design values of the moments of resistance of the columns and the sum of the design values of the moments of
resistance of the beams framing into the joint, respectively. The value of
MRc should correspond to the column axial force(s) in the seismic design
situation for the considered sense of the seismic action.
c) At a beam end where the beam is supported indirectly by another beam instead of framing into a vertical member, the beam end moment, Mi,d, may
be taken as equal to the acting moment at the beam end section in a seismic
design situation.
4.5.1.1.2
Columns
In primary seismic columns, the design values of shear forces are determined
in accordance with the capacity design rule, on the basis of the equilibrium of
the column under end moments Mi,d (with i=1.2 denoting the end stations of the
column), corresponding to plastic hinge formation for positive and negative directions of seismic loading. The plastic hinges should be taken to form at the
ends of the beams connected to the joints into which the column end frames, or
(if they form there first) at the ends of the columns (see Figure 4-2).
max VCD ,c
M Rd ,b
Rd M Rd ,c1 min 1,
M
Rd ,c
M Rd ,b
+ M Rd ,c 2 min 1,
i
M Rd ,c
lcl
End moments Mi,d is determined as follows:
M Rb
M i ,d = Rd M Rc ,i min 1,
M
Rc
(EC8 Eq. 5.9)
Member Design
4-7
M Rc
M Rb
M Rb > M Rc
Rd M Rc ,1
1
lc1
Rd ( M Rb M Rc ) M Rc,2
M Rb < M Rc
M Rb
M Rc
Figure 4-2 Capacity Design Shear Force for Columns
where
Rd is the factor accounting for possible overstrength due to steel strain hardening, which in the case of DCH beams is taken as equal to 1.3;
MRc,i is the design value of the column moment of resistance at end i in the
sense of the seismic bending moment under the considered sense of the seismic
action;
4-8
Member Design
MRc and MRb are the sum of the design values of the moments of resistance
of the columns and the sum of the design values of the moments of resistance
of the beams framing into the joint, respectively.
The value of MRc should correspond to the column axial force(s) in the seismic design situation for the considered sense of the seismic action.
4.5.1.2
Design Resistance
The beam and column bending resistance is computed in accordance with EN

1992-1-1:2004 (EC8 5.5.3.1.1(1)P).
The beam shear resistance is computed in accordance with EN 1992-1-1:2004
with the following exceptions (EC8 5.5.3.1.1):
(1) In the critical regions of primary seismic beams, the strut inclination, , in
the truss model is 45.
(2) With regard to the arrangement of shear reinforcement within the critical
region at an end of a primary seismic beam where the beam frames into a
column, the following cases should be distinguished, depending on the
algebraic value of the ratio:
= VEd,min/VEd,max ratio between the minimum and maximum acting

shear forces, as derived in accordance with EC8 section 5.5.2.1(3).
(a) If 0.5, the shear resistance provided by the reinforcement should
be computed in accordance with EN 1992-1-1:2004.
(b) If < 0.5, i.e. when an almost full reversal of shear forces is expected, then:
(i) if VE
max
( 2 + ) f ctd bw d (EC8 Eqn. 5.27)
where fctd is the design value of the concrete tensile strength from
EN 1992-1-1:2004, the same rule as in (a) of this section applies.
(ii) if |VE|max exceeds the limit value in expression (EC8 Eqn. 5.27),
inclined reinforcement should be provided in two directions, either
at 45 to the beam axis or along the two diagonals of the beam in
Member Design
4-9

elevation, and half of |VE|max should be resisted by stirrups and
half by inclined reinforcement.
In such a case, the verification is carried out by means of the condition:
0.5VE max 2 As f yd sin ( EC8 Eqn. 5.28)

where,
As is the area of the inclined reinforcement in one direction, crossing the
potential sliding plane (i.e. the beam end section);
is the angle between the inclined reinforcement and the beam axis
(normally =45 , or tan ( d d ) lb .
NOTE: Inclined stirrups are not designed at this time (EC8 5.5.3.1.2(3)). Only
vertical stirrups are designed for case EC8 5.5.3.1.2(b) for the full shear force.
The column shear resistance is computed in accordance with EN 1992-11:2004, with the following exceptions (EC8 5.5.3.2.1):
In primary seismic columns, the value of the normalized axial force vd should
not exceed 0.55 (EC8 5.5.3.2.1(3)P). Otherwise the program generates a warning message.
vd =
4.5.1.3
N Ed
f cd Ag
(EC8 5.5.3.3(3))
Joint Design
To ensure that the beam-column joint of a Ductility Class High Moment

Resisting Frame (DCH MRF) possesses adequate shear strength, the program
performs a rational analysis of the beam-column panel zone to determine the
shear forces that are generated in the joint. The program then checks this
against design shear strength.
Only joints having a column below the joint are checked. The material properties of the joint are assumed to be the same as those of the column below the
joint.
4 - 10
Member Design
The joint analysis is completed in the major and the minor directions of the
column. The joint design procedure involves the following steps:
Determine the panel zone design shear force, V jhd
Determine the effective area of the joint
Design panel zone shear rebar/stirrup
The algorithms associated with these three steps are described in detail in the
following three sections.
4.5.1.3.1
Determine the Panel Zone Shear Force
Figure 4-3 illustrates the free body stress condition of a typical beam-column
intersection for a column direction, major or minor.
The force V jhd is the horizontal panel zone shear force that is to be calculated.
L
R
The forces that act on the joint are NEd, VC, M Ed
, and M Ed
. The forces NEd and
VC are the design axial force and design shear force, respectively, from the colL
R
and M Ed
are obumn framing into the top of the joint. The moments M Ed
tained from the beams framing into the joint. The program calculates the joint
shear force V jhd by resolving the moments into C and T forces. Noting that TL
= CL and TR = CR,
V jhd = TL + TR VC
The location of C or T forces is determined by the direction of the moment.
The magnitude of C or T forces is conservatively determined using basic principles of ultimate strength theory.
The program resolves the moments and the C and T forces from beams that
frame into the joint in a direction that is not parallel to the major or minor directions of the column along the direction that is being investigated, thereby
contributing force components to the analysis. Also, the program calculates the
C and T for the positive and negative moments, considering the fact that the
concrete cover may be different for the direction of moment.
Member Design
4 - 11

In the design of Ductility Class High Moment Resisting Frames (DCH MRF),
the evaluation of the design shear force is based on the moment capacities
(with a reinforcing steel overstrength factor due to steel strain hardening, Rd,
which in the case of DCH MRF beams is taken as equal to 1.2 (EC8 5.5.2.3
(2)). The C and T force are based on those moment capacities. The program
calculates the column shear force VC from the beam moment capacities, as follows (see Figure 4-3):
VC =
L
R
+ M Ed
M Ed
H
It should be noted that the points of inflection shown on Figure 4-3 are taken as
midway between actual lateral support points for the columns. If no column exists
at the top of the joint, the shear force from the top of the column is taken as zero.
POINT OF
INFLECTION
VEd
COLUMN
ABOVE
COLUMN
HEIGHT
(H)
TOP OF BEAM
PANEL
ZONE
L
M Ed
TL
V jhd
CL
CR
TR
COLUMN
BELOW
R
M Ed
VEd
POINT OF
INFLECTION
ELEVATION
Figure 4-3 Column shear force VC
4 - 12
Member Design
The effects of load reversals, as illustrated in Case 1 and Case 2 of Figure 4-4,
are investigated and the design is based on the maximum of the joint shears
obtained from the two cases.
Figure 4-4 Beam-column joint analysis
Member Design
4 - 13
4.5.1.3.2
Determine the Effective Area of Joint
The joint area that resists the shear forces is assumed always to be rectangular
in plan view. The dimensions of the rectangle correspond to the major and minor dimensions of the column below the joint, except if the beam framing into
the joint is very narrow. The effective width of the joint area to be used in the
calculation is limited as follows:
If b=
min {bc , ( bw + 0.5hc )} ;
c > bw , b j
(EC8 Eqn. 5.34a, 5.5.3.3(2))
If b=
min {bw , ( bc + 0.5hc )} ;
c < bw , b j
(EC8 Eqn. 5.34a, 5.5.3.3(2))
where
bc = cross-sectional dimension of column,
bw = width of web of a beam, and
hc = cross-sectional depth of column in the direction of interest.
The joint area for joint shear along the major and minor directions is calculated
separately (EC8 5.5.3.3).
It should be noted that if the beam frames into the joint eccentrically, the preceding assumptions may not be conservative and the user should investigate
the acceptability of the particular joint.
4.5.1.3.3
Check Panel Zone Shear Force
The panel zone shear force is evaluated by comparing it with the following design shear strengths (EC85.5.3.3(2)).
V jhd
vd
f cd 1 b j h jc for interior joints,
vd
0.8f cd 1 b j h jc for exterior joints,
where,
=
0.6 (1 f ck 250 )
4 - 14
Member Design
(EC8 Eq. 5.33)
h jc is the distance between extreme layers of column reinforcement;
b j is as defined by EC8 equation 5.34a and 5.34 b;

vd is the normalized axial force in the column above the joint; and
f ck is given in MPa.
4.5.1.4
Design Panel Zone Confinement Reinforcing
The panel zone confinement reinforcing (horizontal hoops) is computed as follows (EC85.5.3.3(3)).
=
Ash
V jhd
b
h
j
jc
f b j h jw
ctd
f ctd + vd f cd
f ywd
(EC8 Eqn. 5.35)
where,
Ash is the total area of the horizontal hoops;

V jhd is the horizontal shear force acting on the concrete core of the joint
h jw is the distance between the top and the bottom reinforcement of the
beam;
h jc is the distance between the extreme layers of column reinforcement;
bj
is as defined in EC8 equation 5.34a and 5.34b;
vd
is the normalized design axial force of the column above
( vd = N Ed
Ac f cd )
Member Design
4 - 15

The horizontal hoops should be uniformly distributed within the depth
h jw between the top and bottom bars of the beam. In exterior joints, they should
enclose the ends of beam bars bent toward the joint (EC85.5.3.3(5)).
Additional requirements for horizontal confinement reinforcement in joints of
primary seismic beam with columns as stipulated in EC8 sections 5.5.3.3(7),
5.4.3.3(1) and 5.4.3.2.2(8)-(11) are NOT enforced by program.
4.5.1.5
Beam-Column Flexural Capacity Ratios
The program calculates the ratio of the sum of the beam moment capacities to
the sum of the column moment capacities. For Ductility Class High Moment
Resisting Frames (DCH MRF), at a particular joint for a particular column
direction, major or minor (EC8 5.2.3.3(2)):
1.3M
M
1.0
(EC8 4.4.2.3(4), 5.2.3.3(2))
= Sum of nominal flexural strengths of columns framing into the

joint, evaluated at the faces of the joint. Individual column flexural strength is calculated for the associated factored axial force.
= Sum of nominal flexural strengths of the beams framing into the

joint, evaluated at the faces of the joint.
The capacities are calculated with no reinforcing overstrength factor due to

steel strain hardening. The beam capacities are calculated for reversed situations (Cases 1 and 2) as illustrated in Figure 4-3, and the maximum summation
obtained is used.
The moment capacities of beams that frame into the joint in a direction that is
not parallel to the major or minor direction of the column are resolved along
the direction that is being investigated, and the resolved components are added
to the summation.
The column capacity summation includes the column above and the column
below the joint. For each load combination, the axial force, N Ed , in each of the
4 - 16
Member Design
columns is calculated from the program design load combinations. For each
design load combination, the moment capacity of each column under the influence of the corresponding axial load is then determined separately for the
major and minor directions of the column, using the uniaxial column
interaction diagram; see Figure 4-5. The moment capacities of the two columns
are added to give the capacity summation for the corresponding design load
combination. The maximum capacity summations obtained from all of the
design load combinations is used for the beam-column capacity ratio.
Figure 4-5 Moment capacity MEd at a given axial load NEd
The beam-column capacity ratio is determined for a beam-column joint only

when the following conditions are met:
the frame is a Ductility Class High Moment Resisting Frame (DCH MRF)
when a column exists above the beam-column joint, the column is concrete
all of the beams framing into the column are concrete beams
Member Design
4 - 17
the connecting member design results are available
the load combo involves seismic load
The beam-column flexural capacity ratios (1.3 M b
M )
c
are reported only
for Ductility Class High Moment Resisting Frames involving seismic design
load combinations. If this ratio is greater than 1.0, a warning message is printed in the output.
4.5.1.6
Minimum and Maximum Tensile Reinforcement
The minimum flexural tensile reinforcement ratio in a beam section is limited

to the following minimum value (EC8 5.5.3.1.3(5)):
f
0.5 ctm
min =
f yk
(EC8 5.5.3.1.3(5), 5.4.3.1.2(5))
The maximum flexural tensile reinforcement ratio in a beam section within

plastic hinge is limited to the following maximum values (EC8 5.5.3.1.3(3)):
0.0018 f cd
sy ,d f yd
(EC8 5.5.3.1.3(3), 5.4.3.1.2 (4))
= 2qo 1 if T1 Tc
(EC8 5.2.3.4(3), Eqn. 5.4)
= 1 + ( 2qo 1) Tc T1 if T1 < Tc
(EC8 5.2.3.4(3), Eqn. 5.5)
max = +
where,
However, the preceding limit is NOT enforced in the program. The user must
manually check the preceding limit at potential hinge locations.
The minimum and maximum flexural tensile reinforcement ratio required in a
column section is limited to the following (EC8 5.5.3.2.2(3), 5.4.3.2.2(3)):
The total longitudinal reinforcement ratio, 1 , is limited as follows:
4 - 18
min =
0.01
(EC8 5.4.3.2.2(1))
max =
0.04
(EC8 5.4.3.2.2(1))
Member Design
4.5.2
Ductility Class Medium Moment-Resisting Frames (DCM MRF)

For this framing system
( qo=
3.0u 1 , u 1= 1.1 1.3) (EC8 5.2.2.2(5),
Table 5.1), the additional requirements described in the sections that follow are
checked or reported (EC8 5.5).
NOTE: The geometrical constraints and material requirements given in EC8
Section 5.4.1 should be independently checked by the user because the program dost not perform those checks.
4.5.2.1
Design Forces
4.5.2.1.1
Beams
The design values of bending moments and axial forces are obtained from the
analysis of the structure for the seismic design situation in accordance with EN
1990:2001 section 6.4.3.4, taking into account second order effects in accordance with section 4.4.2.2 and the capacity design requirements of section
5.2.3.3(2) (EC8 5.5.2). The design values of shear forces of primary seismic
beams and columns are determined in accordance with sections 5.4.2.1 and
5.4.2.2, respectively.
In primary seismic beams, the design shear forces are determined in accordance with the capacity design rule, on the basis of the equilibrium of the beam
under: (a) the transverse load acting on it in the seismic design situation and (b)
end moments Mi,d (with i = 1,2, denoting the end sections of the beam), corresponding to plastic hinge formation for positive and negative directions of
seismic loading. The plastic hinges should be taken to form at the ends of the
beams or (if they form there first) in the vertical elements connected to the
joints into which the beam ends frame (see Figure 4-1) (EC8 5.4.2.2(1)P).
The above condition should be implemented as follows (EC8 5.4.2.2(2)P,
5.4.2.2(3)P).
a) At end section i, two values of the acting shear force should be calculated,
i.e. the maximum VEd,max,i and the minimum VEd,min,i corresponding to the
maximum positive and the maximum negative end moments Mi,d that can
develop at ends 1 and 2 of the beam.
Member Design
4 - 19
Rd
max Vi ,d
min Vi ,d
M Rd
,bi min 1,
M
M
Rd ,c
Rd ,b
+
+ M Rd
,bj min 1,
M
M
Rd ,c
Rd ,b
lcl
+
Rd M Rd
,bi min 1,
M
M
Rd ,c
Rd ,b
+ M Rd
,bj min 1,
lcl
M
M
Rd ,c
Rd ,b
+ Vg + 2 q ,o
+ Vg + 2 q ,o
b) End moments Mi,d is determined as follows:
M i ,d = Rd M Rb ,i min 1,
M
M
Rc
Rb
(EC8 Eq. 5.8)
where
Rd is the factor accounting for possible overstrength due to steel strain
hardening, which in the case of DCM beams is taken as equal to 1.0;
MRb,i is the design value of the beam moment of resistance at end i in the
sense of the seismic bending moment under the considered sense of the
seismic action;
MRc and MRb are the sum of the design values of the moments of resistance of the columns and the sum of the design values of the moments of
resistance of the beams framing into the joint, respectively. The value of
MRc should correspond to the column axial force(s) in the seismic design
situation for the considered sense of the seismic action.
c) At a beam end where the beam is supported indirectly by another beam, instead of framing into a vertical member, the beam end moment Mi,d may be
taken as equal to the acting moment at the beam end section in the seismic
design situation.
4 - 20
Member Design
4.5.2.1.2
Columns
In primary seismic columns the design values of shear forces is determined in

accordance with the capacity design rule, on the basis of the equilibrium of the
column under end moments Mi,d (with i = 1,2 denoting the end sections of the
column), corresponding to plastic hinge formation for positive and negative directions of seismic loading. The plastic hinges should be taken to form at the
ends of the beams connected to the joints into which the column end frames, or
(if they form there first) at the ends of the columns (see Figure 4-2).
max VCD ,c
Rd M Rd ,c1 min 1,
M
M
Rd ,b
Rd ,c
+ M Rd ,c 2 min 1,
M
M
Rd ,b
Rd ,c
lcl
End moments Mi,d is determined as follows:
M i ,d = Rd M Rc ,i min 1,
M
M
Rb
Rc
(EC8 Eqn. 5.9)
where
Rd is the factor accounting for possible overstrength due to steel strain hardening, which in the case of DCM beams is taken as equal to 1.1;
MRc,i is the design value of the column moment of resistance at end i in the
sense of the seismic bending moment under the considered sense of the seismic
action;
MRc and MRb are the sum of the design values of the moments of resistance
of the columns and the sum of the design values of the moments of resistance
of the beams framing into the joint, respectively.
The value of MRc should correspond to the column axial force(s) in the seismic design situation for the considered sense of the seismic action.
Member Design
4 - 21
4.5.2.2
Design Resistance
The beam and column bending resistance and beam shear is computed in accordance with EN 1992-1-1:2004 (EC8 5.4.3.1.1(1)P).
The column shear resistance is computed in accordance with EN 1992-11:2004 with the following exception (EC8 5.4.3.2.1):
In primary seismic columns the value of the normalized axial force vd should
not exceed 0.65 (EC8 5.4.3.2.1(3)P). Otherwise, the program generates a warning message.
4.5.2.3
Minimum and Maximum Tensile Reinforcement
The minimum flexural tensile reinforcement ratio in a beam section is limited

to the following minimum value (EC8 5.4.3.1.3(5)):
f
0.5 ctm
min =
f yk
(EC8 5.4.3.1.2(5))
The maximum flexural tensile reinforcement ratio in a beam section within a

plastic hinge is limited to the following maximum values (EC8 5.4.3.1.3(4)):
0.0018 f cd
sy ,d f yd
(EC8 5.4.3.1.2 (4))
= 2qo 1 if T1 Tc
(EC8 5.2.3.4(3))
= 1 + ( 2qo 1) Tc T1 if T1 < Tc
(EC8 5.2.3.4(3))
max = +
where,
However, the preceding limit is NOT enforced in the program. The user must
manually check the preceding limit at the potential hinge locations.
The minimum and maximum flexural tensile reinforcement ratio required in a
column section is limited to the following (EC8 5.5.3.2.2(3), 5.4.3.2.2(3)):
The total longitudinal reinforcement ratio, 1 , is limited as follows:
4 - 22
Member Design
4.5.3
min 0.01
(EC8 5.4.3.2.2(1))
max 0.04
(EC8 5.4.3.2.2(1))
Ductility Class Low Moment-Resisting Frames (DCL MRF)

Seismic design for Ductility Class Low Moment Resisting Frames (DCL MRF)
is completed in accordance with EN 1992-1-1:2004 without any additional requirements other than EC8 section 5.3.2. Reinforcing class B or C in EN 19921-1:2004, Table C.1 is permitted for DCL MRF(EC8 5.3.2). The program does
not perform any special check when DCL MRF is specified.
4.5.4
Special Consideration for Seismic Design

For Special Moment Resisting Concrete Frames (seismic design), the beam design satisfies the following additional conditions (see also Table 4-1):
Table 4-1: Design Criteria

Type of
Check/
Design
Ductility Class Low

Moment Resisting Frames
(DCL MRF)
Ductility Class Medium

(DCM MRF)
Ductility Class High

(DCH MRF)
Column Check (interaction)

Specified Combinations
0.2% < < 4%
1% < < 4%
1% < < 4%
Column Capacity Shear

Rd = 1.1
Column Capacity Shear

Rd = 1.3
Column Design (interaction)
Column Shears
Member Design
4 - 23
Table 4-1: Design Criteria

Type of
Check/
Design
Ductility Class Low

(DCL MRF)
Ductility Class Medium

(DCM MRF)
Ductility Class High

(DCH MRF)
Beam Design Flexure

min
f
ctm
0.26
max
f
yk
0.0013
min
f
0.5 ctm
f yk
f
min 0.5 ctm
f yk
max 0.004
Beam Min. Moment Override Check
No Requirement
1
+
M u ,end M u ,end
2
1
M span max M ,M
max
2
1
+
Mu,end Mu,end
2
{
{
}
}
1
+
+
M span max M ,M
end
4
1
M span max M ,M
2
end
Beam Design Shear

Beam Capacity Shear (Ve)
Rd = 1.0
Beam Capacity Shear (Ve)
Rd = 1.2
Joint Design
No Requirement
No Requirement
Checked for shear
No Requirement
Checked
Beam/Column Capacity Ratio

No Requirement
4 - 24
At any end (support) of the beam, the beam positive moment capacity (i.e.,
associated with the bottom steel) in DCH MRF and DCM MRF would not
be less that 1/2 of the beam negative moment capacity (i.e., associated with
the top steel) at that end (EC8 5.4.3.1.2(4)).
Neither the negative moment capacity nor the positive moment capacity at
any of the sections within the beam in DCH MRF would be less than 1/4 of
the maximum of positive or negative moment capacities of any of the beam
end (support) stations (EC8 5.5.3.1.3(5)).
Member Design
APPENDICES
Appendix A
Second Order P-Delta Effects
Typically, design codes require that second order P-Delta effects be considered
when designing concrete frames. These effects are the global lateral translation
of the frame and the local deformation of members within the frame.
Consider the frame object shown in Figure A-1, which is extracted from a story
level of a larger structure. The overall global translation of this frame object is
indicated by . The local deformation of the member is shown as . The total
second order P-Delta effects on this frame object are those caused by both and
.
The program has an option to consider P-Delta effects in the analysis. When
P-Delta effects are considered in the analysis, the program does a good job of
capturing the effect due to the deformation shown in Figure A-1, but it does
not typically capture the effect of the deformation (unless, in the model, the
frame object is broken into multiple elements over its length).
Consideration of the second order P-Delta effects is generally achieved by
computing the flexural design capacity using a formula similar to that shown in
the following equation.
MCAP =
MCAP =
aMnt + bMlt
where,
Flexural design capacity required

A-1
Figure A-1 The total second order P-delta effects on a

frame element caused by both and
Mnt
Required flexural capacity of the member assuming there is no

joint translation of the frame (i.e., associated with the deformation in Figure A-1)
Mlt
Required flexural capacity of the member as a result of lateral

translation of the frame only (i.e., associated with the deformation in Figure A-1)
Unitless factor multiplying Mnt
Unitless factor multiplying Mlt (assumed equal to 1 by the program;

see the following text)
When the program performs concrete frame design, it assumes that the factor b
is equal to 1 and calculates the factor a. That b = 1 assumes that P-Delta
effects have been considered in the analysis, as previously described. Thus, in
general, when performing concrete frame design in this program, consider
P-Delta effects in the analysis before running the program.
A-2
Appendix A
Appendix B
Member Unsupported Lengths and
Computation of -Factors
The column unsupported lengths are required to account for column slenderness
effects. The program automatically determines the unsupported length
ratios, which are specified as a fraction of the frame object length. Those ratios
times the frame object length give the unbraced lengths for the members. Those
ratios also can be overwritten by the user on a member-by-member
basis, if desired, using the overwrite option.
There are two unsupported lengths to consider. They are l33 and l22, as shown in
Figure B-1. These are the lengths between support points of the member in the
corresponding directions. The length l33 corresponds to instability about the 3-3
axis (major axis), and l22 corresponds to instability about the 2-2 axis (minor
axis).
In determining the values for l22 and l33 of the members, the program recognizes
various aspects of the structure that have an effect on those lengths, such as
member connectivity, diaphragm constraints and support points. The program
automatically locates the member support points and evaluates the corresponding unsupported length.
B-1
It is possible for the unsupported length of a frame object to be evaluated by the

program as greater than the corresponding member length. For example, assume
a column has a beam framing into it in one direction, but not the other, at a floor
level. In that case, the column is assumed to be supported in one direction only at
that story level, and its unsupported length in the other direction will exceed the
story height.
Figure B-1 Axis of bending and unsupported length
B-2
Member Unsupported Lengths and Computation of -Factors
Appendix C
Concrete Frame Design Preferences
The Concrete Frame Design Preferences are basic assignments that apply to all
of the concrete frame members. Table C-1 lists the Concrete Frame Design
Preferences for the Eurocode 2-2004 code Default values are provided for all
preference items. Thus, it is not necessary to specify or change any of the preferences. However, at least review the default values to ensure they are acceptable. Some of the preference items also are available as member specific
overwrite items. The Overwrites are described in Appendix D. Overwritten
values take precedence over the preferences.
Table C-1 Preferences
Possible
Values
Default
Value
Country
CEN Default
United Kingdom
CEN Default
Toggle to choose the country for which the

Nationally Determined Parameters [NDPs]
should be used. The various NDPs and
their associated values for each country are
described in Appendix F.
Combinations
Equation
Eq. 6.10
Max of Eq.
6.10a/6.10b
Eq. 6.10
Toggle to choose which equation is used to

generate automatic load combinations.
Item
Description
C-1
Possible
Values
Default
Value
Second Order
Method
Nominal
Stiffness
Nominal
Curvature
None
Nominal
Curvature
Toggle to choose the method to be used to

calculate isolated member P- effects. If
None is chosen, these effects should be
captured by alternative methods.
Time History
Design
Envelopes,
Step-by-Step
Envelopes
Toggle for design load combinations that

include a time history designed for the
envelope of the time history, or designed
step-by-step for the entire time history. If a
single design load combination has more
than one time history case in it, that design
load combination is designed for the envelopes of the time histories, regardless of
what is specified here.
Number of
Interaction Curves
Multiple of 4
4
24
Number of equally spaced interaction

curves used to create a full 360-degree
interaction surface (this item should be a
multiple of four). We recommend 24 for this
item.
Number of
Interaction
Points
Any odd value

5
11
Number of points used for defining a single

curve in a concrete frame; should be odd.
Consider
Minimum
Eccentricity
No, Yes
Yes
Toggle to specify if minimum eccentricity is

considered in design.
Theta0 (ratio)
>0
0.005
Inclination angle for imperfections.
GammaS (steel)
>0
1.15
Partial safety factor for steel.
GammaC
(concrete)
>0
1.5
Partial safety factor for concrete.
AlphaCC
(compression)
>0
Item
C-2
Appendix C
Description
Material coefficient taking account of longterm effects on the concrete compressive

strength and unfavorable effects from the
load application.
Appendix C Concrete Frame Design Preferences
Possible
Values
Default
Value
AlphaCT
(tension)
>0
Material coefficient taking account of longterm effects on the concrete tensile

strength and unfavorable effects from the
load application.
AlphaLCC (Lightweight compression)
>0
0.85
Light-weight material coefficient taking

account of long-term effects on the concrete compressive strength and unfavorable effects from the load application.
AlphaLCT
(Lightweight
tension)
>0
0.85
Light-weight material coefficient taking

account of long-term effects on the concrete tensile strength and unfavorable
effects from the load application.
Pattern Live
Load Factor
0.75
The live load factor for automatic generation of load combinations involving pattern
live loads and dead loads.
Utilization Factor
Limit
>0
0.95
Stress ratios that are less than or equal to

this value are considered acceptable.
Item
Description
Preferences
C-3
Appendix D
Concrete Frame Overwrites
The concrete frame design overwrites are basic assignments that apply only to
those elements to which they are assigned. Table D-1 lists concrete frame
design overwrites for Eurocode 2-2004. Default values are provided for all
overwrite items. Thus, it is not necessary to specify or change any of the overwrites. However, at least review the default values to ensure they are acceptable.
When changes are made to overwrite items, the program applies the changes
only to the elements to which they are specifically assigned.
Table D-1 Overwrites
Item
Possible
Values
Default
Value
Current
Design
Section
Any defined concrete

section
Analysis
section
The design section for the selected frame

objects.
Element
Type
Sway
Nonsway
From
Reference
Frame type defined as sway (unbraced) or

nonsway (braced).
Live Load
Reduction
Factor
Calculated
The reduced live load factor. A reducible live

load is multiplied by this factor to obtain the
reduced live load for the frame object.
Specifying 0 means the value is program
determined.
Description
D-1
Possible
Values
Default
Value
Unbraced
Length Ratio
(Major)
Calculated
Unbraced length factor for buckling about the

frame object major axis. This item is specified
as a fraction of the frame object length.
Multiplying this factor times the frame object
length gives the unbraced length for the
object. Specifying 0 means the value is
program determined.
Unbraced
Length Ratio
(Minor)
0.60
Unbraced length factor for buckling about the

frame object minor axis. Multiplying this factor
times the frame object length gives the unbraced length for the object. Specifying 0
means the value is program determined. This
factor also is used in determining the length for
lateral-torsional buckling.
Effective
Length Factor
( Major)
>0
Calculated
EC2 does not specify this, but it is included to

allow the user to overwrite the program
determined effective length. Effective length
factor for buckling about the frame object
major axis. This item is specified as a fraction
of the frame object length.
Effective
Length Factor
( Minor)
>0
Calculated
EC2 does not specify this, but it is included to

allow the user to overwrite the program
determined effective length. Effective length
factor for buckling about the frame object
minor axis. This item is specified as a fraction
of the frame object length.
Correction
Factor, Kr
>0
1.0
Correction factor depending on axial load that

is used by the Nominal Curvature method for
computing additional moments.
Creep Factor,
KPhi
>0
1.0
Creep factor that is used by the Nominal

Curvature method for computing additional
moments.
Item
D-2
Appendix D
Description
Appendix E
Error Messages and Warnings
Table E-1 provides a complete list of Concrete Errors messages and Warnings.
Table E-1 Error Messages
Error
Number
Description
Beam concrete compression failure
Reinforcing required exceeds maximum allowed
Shear stress exceeds maximum allowed
Column design moments cannot be calculated
Column factored axial load exceeds Euler Force
Required column concrete area exceeds maximum
Flexural capacity could not be calculated for shear design
Concrete column supports non-concrete beam/column
E-1
Error
Number
E- 2
Description
k L/r > 115 , zeta_ 2 < 0 , eta < 1.0 (GB50010 7.3.10)
10
Column is overstressed for P-M-M
11
Axial compressive capacity for concrete exceeded (TBM 6.4.2)
12
Beam frames into column eccentrically (11.6.3)
13
Torsion exceeds maximum allowed
14
Reinforcing provided is below minimum required
15
Reinforcing provided exceeds maximum allowed
16
Tension reinforcing provided is below minimum required
17
k L/r > 30 (GB 7.3.10)
21
The column is not ductile. Beam/column capacity ratio is not

needed.
22
The load is not seismic. Beam/column capacity ratio is not

needed.
23
There is no beam on top of column. Beam/column capacity ratio

is not needed.
24
At least one beam on top of column is not of concrete.

Beam/column capacity ratio is not calculated.
25
The column on top is not concrete. Beam/column capacity ratio is

not calculated.
26
The station is not at the top of the column. Beam/column capacity

ratio is not needed.
27
The column is not ductile. Joint shear ratio is not needed.
Appendix E
Appendix E Error Messages and Warnings
Error
Number
Description
28
The load is not seismic. Joint shear ratio is not needed.
29
There is no beam on top of column. Joint shear ratio is not

needed.
30
At least one beam on top of column is not concrete. Joint shear

ratio is not calculated.
31
The column on top is not concrete. Joint shear ratio is not needed.
32
The station is not at the top of the column. Joint shear ratio is not
needed.
33
Beam/column capacity ratio exceeds limit.
34
Joint shear ratio exceeds limit.
35
Capacity ratio exceeds limit.
36
All beams around the joint have not been designed.

Beam/column capacity ratio is not calculated.
37
At least one beam around the joint has failed. Beam/column capacity ratio is not calculated.
38
The column above the joint has not been designed. Beam/column
capacity ratio is not calculated.
39
The column above the joint has failed. Beam/column capacity

40
All beams around the joint have not been designed. Joint shear
41
At least one beam around the joint has failed. Joint shear ratio is
not calculated.
42
The column above the joint has not been designed. Joint shear
Appendix E
E- 3
Error
Number
E- 4
Description
43
The column above the joint has failed. Joint shear ratio is not
calculated.
45
Shear stress due to shear force and torsion together exceeds

maximum allowed.
Appendix E
Appendix F
Nationally Determined Parameters (NDPs)
The Comit Europen de Normalisation (CEN) version of Eurocode 2-2004

specifies a set of clauses in the design code, for which Nationally Determined
Parameters (NDPs) are permitted to be adjusted by each member country within
their National Annex. Variations in these parameters between countries are
considered in the program by choosing the desired country in the Preferences.
This appendix lists the NDPs as adopted in the program for the CEN Default
version of the design code. Additional tables are provided that list the NDPs that
differ from the CEN Default values for each country supported in the program.
Table F-1 CEN Default NDPs
NDP
Clause
Value
2.4.2.4(1)
1.5
2.4.2.4(1)
1.15
cc
3.1.6(1)
1.0
ct
3.1.6(2)
1.0
F-1
F- 2
NDP
Clause
Value
max fyk
3.2.2(3)
600MPa
Load Combinations
5.1.3(1)
Combinations from Eq. 6.10
5.2(5)
0.005
k1
5.5(4)
0.44
k2
5.5(4)
1.25(0.6 + 0.0014/cu2)
k3
5.5(4)
0.54
k4
5.5(4)
1.25(0.6 + 0.0014/cu2)
lim
5.8.3.1(1)
20 A B C / n
Second Order Analysis Method
5.8.5(1)
Nominal Curvature
CRd,c
6.2.2(1)
0.18/c
vmin
6.2.2(1)
0.035k3/2fck1/2
k1
6.2.2(1)
0.15
Cot
6.2.3(2)
1 Cot 2.5
6.2.3(3)
0.6 1 ck
250
cw
6.2.3(3)
1.0
Beam As,min
9.2.1.1(1)
Beam As,max
9.2.1.1(3)
Appendix F
0.26
f ctm
bt d 0.0013bt d
f yk
0.04Ac
Appendix F Nationally Determined Parameters (NDPs)

NDP
Clause
Value
Beam w,min
9.2.2(5)
Column As,min
9.5.2(2)
0.10 N Ed
0.002 A c
f yd
Column As,max
9.5.2(3)
0.04Ac
lcc
11.3.5(1)
0.85
lct
11.3.5(2)
0.85
ClRd,c
11.6.1(1)
0.15/c
vl,min
11.6.1(1)
0.30k3/2flck1/2
k1
11.6.1(1)
0.15
11.6.2(1)
0.51(1 flck/250)
NDP
Clause
Value
0,i (wind load)
EC0 Combos
0.5
cc
3.1.6(1)
0.85
k1
5.5(4)
0.4
k2
5.5(4)
0.6 + 0.0014/cu2
k3
5.5(4)
0.4
( 0.08
f ck / f yk
Table F-2 United Kingdom NDPs
Appendix F
F- 3
Table F-2 United Kingdom NDPs

NDP
Clause
Value
k4
5.5(4)
0.6 + 0.0014/cu2
vl,min
11.6.1(1)
0.30k3/2flck1/2
NDP
Clause
Value
Column As,min
9.5.2(2)
0.15 N Ed
0.003 A c
f yd
NDP
Clause
Value
cc
3.1.6(1)
0.85
ct
3.1.6(2)
0.85
lim
5.8.3.1(1)
13(2 rm)Af
k1
6.2.2(1)
0.15 for compression

0.3 for tension
Beam w,min
9.2.2(5)
( 0.1 f ) / f
Column As,min
9.5.2(2)
0.5 N Ed 0.2 Ac fcd
f yd
f yd
Table F-3 Slovenia NDPs
Table F-4 Norway NDPs
ck
yk
but not less than 0.01Ac

Column As,max
F- 4
Appendix F
9.5.2(3)
0.08Ac
Table F-4 Norway NDPs

NDP
Clause
Value
vl,min
11.6.1(1)
0.028k3/2flck1/2
k1
11.6.1(1)
0.15 for compression

0.3 for tension
11.6.2(1)
0.5(1 flck/250)
NDP
Clause
Value
cc
3.1.6(1)
0.85
k1
5.5(4)
0.4
k2
5.5(4)
0.6 + 0.0014/cu2
k3
5.5(4)
0.54
k4
5.5(4)
0.6 + 0.0014/cu2
vlim
5.8.3.1(1)
0.30k3/2flck1/2
NDP
Clause
Value
Beam As,max
9.2.1.1(3)
Unlimited
9.5.2(2)
0.002Ac
Table F-5 Singapore NDPs
Table F-6 Sweden NDPs
Column As,min
Appendix F
F- 5
Table F-6 Sweden NDPs

NDP
Clause
Value
Column As,max
9.5.2(3)
Unlimited
lcc
11.3.5(1)
1.0
lct
11.3.5(2)
1.0
NDP
Clause
Value
cc
3.1.6(1)
0.85
Max fyk
3.2.2(3)
700MPa
Load Combinations
5.1.3(1)
Combinations from Eq. 6.10a/b
k2
5.5(4)
1.10
Beam As,max
9.2.1.1(3)
Unlimited
Column As,max
9.5.2(3)
0.06Ac
NDP
Clause
Value
2.4.2.4(1)
1.45
2.4.2.4(1)
1.20
Max fyk
3.2.2(3)
650MPa
Table F-7 Finland NDPs
Table F-8 Denmark NDPs
F- 6
Appendix F
Table F-8 Denmark NDPs

NDP
Clause
Value
Load Combinations
5.1.3(1)
Combinations from Eq. 6.10a/b
lim
5.8.3.1(1)
5.8.5(1)
Nominal Stiffness
Beam w,min
9.2.2(5)
( 0.063
lcc
11.3.5(1)
1.0
lct
11.3.5(2)
1.0
vl,min
11.6.1(1)
0.03k3/2flck1/2
Clause
Value
3.2.2(3)
500MPa
Ac f cd
N Ed
20
f ck / f yk
Table F-9 Portugal NDPs

NDP
Max fyk
Table F-10 Germany NDPs

NDP
Clause
Value
cc
3.1.6(1)
0.85
ct
3.1.6(2)
0.85
max fyk
3.2.2(3)
500MPa
Appendix F
F- 7
F- 8
NDP
Clause
Value
5.2(5)
0 h 1.0
k1
5.5(4)
0.64
k2
5.5(4)
0.8
k3
5.5(4)
0.72
k4
5.5(4)
0.8
lim
5.8.3.1(1)
5.8.5(1)
Nominal Stiffness
CRd,c
6.2.2(1)
0.15/c
vmin
6.2.2(1)
k1
6.2.2(1)
0.12
Cot
6.2.3(2)
1 Cot 3.0
6.2.3(3)
0.752 where
2 = (1.1-fck/500) 1.0
Beam As,max
9.2.1.1(3)
0.08Ac
Beam w,min
9.2.2(5)
0.16fctm/fyk
Column As,min
9.5.2(2)
0.15|NEd| / fyd
lcc
11.3.5(1)
0.75
Appendix F
25 for n 0.41
16
n for n < 0.41
( 0.0525 c ) k 3 2 f ck1 2 for

( 0.0375 c ) k 3 2 f ck1 2 for
d 600mm
d > 800mm

NDP
Clause
Value
vl,min
11.6.1(1)
k1
11.6.1(1)
0.12
11.6.2(1)
0.751
NDP
Clause
Value
2.4.2.4(1)
1.4
Cot
6.2.3(2)
1 Cot 2.0
Column As,min
9.5.2(2)
0.15|NEd| / fyd 0.003Ac
( 0.0525 c ) k 3 2 flck1 2 for

( 0.0375 c ) k 3 2 flck1 2 for
d 600mm
d > 800mm
Table F-11 Poland NDPs
Table F-12 Ireland NDPs

NDP
Clause
Value
cc
3.1.6(1)
0.85
k1
5.5(4)
0.4
k2
5.5(4)
0.6 + 0.0014/cu2
k3
5.5(4)
0.4
k4
5.5(4)
0.6 + 0.0014/cu2
vl,min
11.6.1(1)
0.028k3/2flck1/2
Appendix F
F- 9
References
EC0, 2001. Eurocode 0: Basis of Structural Design (EN 1990:2000), European

Committee for Standardization, rue de Stassart, 36, B-1050 Brussels.
EC2, 2004. Eurocode 2: Design of Concrete Structures Part 1-1: General Rules
and Rules for Buildings (EN 1992-1-1), European Committee for Standardization, rue de Stassart, 36, B-1050 Brussels.
EC8, 2004. Eurocode 8: Design of structures for earthquake resistance Part 1:
General rules, seismic actions and rules for buildings (EN 1998-1:2004),
European Committee for Standardization, rue de Stassart, 36, B-1050
Brussels.
CSI, 2008. CSI Analysis Reference Manual, Computers and Structures, Inc.,
Berkeley, California.
CSI, 2009. CSI Lateral Load Manual. Computers and Structures, Inc., 1995
University Avenue, Berkeley, California, 94704.
References - i

CFD Ec 2 2004 PDF

Uploaded by

Copyright:

Available Formats

CFD Ec 2 2004 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CFD Ec 2 2004 PDF

Uploaded by

Copyright:

Available Formats

Concrete Frame Design Manual

Eurocode 2-2004 with 8-2004

ISO ETA082914M23 Rev. 0

Proudly developed in the United States of America

CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE

1.2 Recommended Reading/Practice

2.2 Design and Check Stations

2.3 Identifying Beams and Columns

2.4 Design of Beams

2.5 Design of Columns

2.6 P-Delta Effects

2.7 Element Unsupported Lengths

Concrete Frame Design Eurocode 2-2004

3.2 Assumptions / Limitations

3.3 Design Load Combinations

3.4 Column Design

Generation of Biaxial Interaction Surface

3.5 Beam Design

4.2 Design Preferences

4.4 Supported Framing Types

4.5 Member Design

4.5.1 Ductility Class High Moment-Resisting Frames 4-4

Second Order P-Delta Effects

Member Unsupported Lengths and Computation of

Concrete Frame Design Preferences

Concrete Frame Overwrites

Error Messages and Warnings

Nationally Determined Parameters (NDPs)

Concrete Frame Design Eurocode 2-2004

Design Load Combinations

Concrete Frame Design Eurocode 2-2004

combinations using maxima/minima permutations of interacting quantities.

Design Load Combinations

Chapter 2 - Design Prerequisites

Design and Check Stations

Identifying Beams and Columns

Design and Check Stations

Concrete Frame Design Eurocode 2-2004

In designing the flexural reinforcement for the major moment at a particular

Chapter 2 - Design Prerequisites

Element Unsupported Lengths

Concrete Frame Design Eurocode 2-2004

Choice of Input Units

Choice of Input Units

This chapter provides a detailed description of the code-specific algorithms used

Area of concrete used to determine shear stress, mm2

Gross area of concrete, mm2

Area enclosed by centerlines of connecting walls for torsion, mm2

Area of tension reinforcement, mm2

Area of compression reinforcement, mm2

Concrete Frame Design Eurocode 2-2004

Area of longitudinal torsion reinforcement, mm2

Area of transverse torsion reinforcement (closed stirrups) per unit

Area of shear reinforcement per unit length of the member,

Modulus of elasticity of concrete, MPa

Modulus of elasticity of reinforcement, assumed as 200 GPa

Moment of inertia of gross concrete section about centroidal axis,

Smaller factored end moment in a column, N-mm

Larger factored end moment in a column, N-mm